Answer:
Neutrons released during a fission reaction cause other nuclei to split
Answer:
B: Neutrons released during a fission reaction cause other nuclei to split
Explanation:
Find the hydroxide concentration of a LiOH soultion that has a pOH of 8.65.
[OH] = _____ (round to 2 decimal places)
Answer: i need help
Explanation:
¿Cómo se llama el grupo IIA de la tabla periódica?
Answer:
los metales alcalinotérreos: berilio (Be), magnesio (Mg), calcio (Ca), estroncio (Sr), bario (Ba) y radio (Ra).
o simplemente llamado grupo 2A
Explanation:
The total pressure of two unknown gases is 5 kPa. The partial pressure of one of the gases is 2.345 kPa, what is the partial pressure of the other gas?
Answer:
[tex]p_2=2.655kPa[/tex]
Explanation:
Hello there!
In this case, according to the Dalton's law, which states that the total pressure is equal the sum of the pressures of the gases in the mixture, we write the following for this system:
[tex]P_T=p_1+p_2[/tex]
Thus, we solve for the partial pressure of the gas #2 as shown below:
[tex]p_2=P_T-p_1\\\\p_2=5kPa-2.345kPa\\\\p_2=2.655kPa[/tex]
Best regards!
Which form of emission is commonly not written in nuclear equations because they do not affect charges, atomic numbers, or mass numbers?
alpha particle
beta particle
gamma ray
Answer: It is Gamma ray
Answer:
C. gamma ray
(Photo for proof at the bottom.)
Explanation:
A gamma ray is a type of radiation that occurs when an unstable nucleus emits a photon, the smallest unit of light. A photon has no mass or charge. Atomic and mass numbers are written based on the mass of the atom. But since no mass is lost when a photon is emitted, writing the emission of it isn't necessary.
Here's a photo of Edge, good luck.
Blank O2 + blank Mg arrow blank MgO
Select the coefficients that balance the equation:
MgO *
A) 1,1,1
B) 1,2,2
C) 2,3,4
D) 1,4, 2
Answer:
its a
Explanation:
a
3. 7moles of Ba(NO3)2 is dissolved in 75kg of distilled water.
What is the boiling point of this solution? Hint: Find molality first.
Answer:
100.14°C
Explanation:
The boling point elevation is a colligative property that describes the increasing in boiling point of a solution regard to the boiling point of the pure solvent. The equation is:
ΔT = Kf*m*i
Where ΔT is boiling point elevation
Kf is boiling point elevation (0.51°C/m for water)
m is molality of the solution (7moles Ba(NO3)2 / 75kg = 0.09333m
i is Van't Hoff factor = 3 for Ba(NO3)2 (Because its dissolution produce 3 ions = Ba²⁺ and 2 NO₃⁻
Replacing:
ΔT = 0.51°C/m*0.09333m*3
ΔT = 0.14°C is the boiling point elevation
As the boiling point of water is 100°C, the boiling point of the solution is:
100°C + 0.14°C =
100.14°C
Hi can someone who know the answers tell me what it is and pls don't send me a link also don't send me the wrong answers if you don't know it's ok :)
Answer:
you diba ikaw ang nagpamalimali diba no
Alex built a model to show how light bends when placed into water. To do this, Alex filled a fish tank up with water, and shined a green laser through the water. The angle he shined the laser into the fish tank is the line above the water, and the angle that the light bent is seen below the water. What is a limitation of this model? The model cannot show how light bends. The model is unable to use different colors of light The model cannot calculate the speed of light The model is not 3 dimensional
Answer:
The model cannot show how light bends.
Explanation:
4. A blue light is shined on objects X and Y. Object X appears to be blue, and object Y appears to
be black. Which of the following is correct?
A. Object X absorbs blue light, and object Y reflects blue light.
B. Object X reflects blue light, and object Y absorbs blue light.
C. Object X must be black, and object Y must be blue.
D. Object X must be blue, and object Y must be black.
A blue light is shined on objects X and Y. Object X appears to be blue, and object Y appears to be black when Object X reflects blue light, and object Y absorbs blue light. Hence option B is correct.
What is light ?Visible light spectrum is nothing but the range of wavelength of radiation from 4000 angstrom to 7000 angstrom(Violet to Red). light is a energy packet. Every Photon having different wavelength travels with same velocity c (velocity of light). When we focus numbers of colors from visible spectrum to a point, that point appears as a white light. hence white light is composed of numbers of Colors in it.
When we pass white light through a prism, as white light enters in the prism all the colors having different wavelength travels with different velocity in the prism due to that there is separation of colors from the white light. Therefore we get different colors of white light in the prism this phenomenon is know as dispersion of light.
Light can be reflected, absorbed, transmitted diffracted and scattered etc.
α + β + ν = 1 where α, β, ν are coefficient of absorption, reflection and transmission.
When any object appears to be black it means that radiation has been absorbed by that body, it has high absorption coefficient. and when a body appears to be colored, it means that object has reflected the particular color, it having high reflection coefficient.
Hence option B is correct.
To know more about light :
https://brainly.com/question/15200315
#SPJ2.
How would you find the density of a can of soda pop?
A. Find the mass of the can of soda pop and then multiply by the number of cubic centimeters in the can
B. Find the mass of the can of soda pop and then divide by the number of cubic centimeters in the can
C. Convert a gallon into cubic centimeters and then divide by the mass of the can of soda pop
D. Convert a gallon into cubic centimeters and then subtract the mass of the can of soda pop
Answer:
it's A.
Explanation:
have uh good day ma :)))))))
Brakes are to a car as
to a nuclear-fission chain reaction.
A. fuel rods are
B. proliferation is
C. free neutrons are
D. control rods are
Answer:
D. control rods are
I hope dis helps :3
Brakers are to a car as control rods are to a nuclear-fission chain reaction. The correct option is D.
What is a nuclear-fission chain?A chain reaction occurs when neutrons generated during fission cause subsequent fission in at least one more nucleus.
This nucleus creates neutrons, and the cycle continues.
The process can be either controlled (nuclear power) or uncontrolled (nuclear weapons) (nuclear weapons).
Thus, the correct option is D. control rods are.
Learn more about nuclear-fission chain
https://brainly.com/question/24297620
in calorimetry, energy is measured through heat transfer from one substance to another. Which of the following is NOT a method of heat transfer?
Answer:
Explanationconvection
:
In calorimetry, energy is measured through heat transfer from one substance to another. Convection is not the method of heat transfer.
What is a calorimeter?A calorimeter is a device used to measure the amount of heat involved in a chemical or physical process.
For example, when an exothermic reaction occurs in solution in a calorimeter, the heat produced by the reaction is absorbed by the solution, which increases its temperature.
One technique we can use to measure the amount of heat involved in a chemical or physical process is known as calorimetry.
Calorimetry is used to measure amounts of heat transferred to or from a substance.
To do so, the heat is exchanged with a calibrated object (calorimeter).
Heat loss due to conduction is prevented by placing the calorimeter box in a well-lagged vessel using wool or cork material.
Heat loss due to convection is prevented by placing a lid on the box.
Heat loss due to radiation is minimized by polishing the box in order to smoothen it.
Learn more about calorimeter here:
https://brainly.com/question/16662844
#SPJ2
Calcula cuantos mililitros de oxigeno se necesitan para quemar 3.5 ml de C₆H₆ a CNTP, la reacción sin balancear es la siguiente: C₆H₆ + O₂ → CO₂ + H₂O
Answer:
[tex]26.25mL \ O_2[/tex]
Explanation:
¡Hola!
En este caso, dado que se nos da reacción de combustión del benceno, primero debemos balancearla como se muestra a continuación:
C₆H₆ + ¹⁵/₂ O₂ → 6CO₂ + 3H₂O
Vemos que hay una relación molar entre el benceno y oxígeno de 1:¹⁵/₂, por lo que la relación de volúmenes es:
[tex]3.5 mL\ C_6H_6*\frac{15/2\ mL\ O_2}{1mL\ C_6H_6} \\\\=26.25mL \ O_2[/tex]
¡Saludos!
What will the change in temperature be when 90 J are applied to 15 g of gold. (Cgold = 0.126 J/gºC)
Round your answer to the nearest whole number.
°C
E
3
4
5
Next
O
I 17
Answer:
48 °C
Explanation:
q = 90J
m = 15 g
C = 0.126 J/gºC
q = mct
90 = (15)(0.126)t
t = 47.62 °C = 48 °C
Answer:
Explanation:
Formula
E = m * c * Δt
Δt is what you seek.
Givens
E = 90 joules
m = 15 grams
c = 0.126
Solution
90 = 15 * 0.126 * Δt Divide by 15
90/15 = 15/15 * 0.126 * Δt
6 = 0.126 * Δt Divide by 0.126
6/0.126 = Δt
47.619 = Δt
Δt = 48 oC
In steps 3 and 4 of the citric acid cycle, successive oxidations produce ________ as a waste product and the four-carbon carrier ________. In steps 3 and 4 of the citric acid cycle, successive oxidations produce ________ as a waste product and the four-carbon carrier ________. CO2; malate CO2; succinyl-SCoA ADP; oxaloacetate ADP; succinyl-SCoA CO2; oxaloacetate
Answer:
CO2; succinyl-SCoA
Explanation:
Citric acid cycle, also called Krebs cycle is the second stage of aerobic cellular respiration, which occurs in the mitochondrion. The kreb's cycle is made up of 7 distinct steps, with each involving series of enzymatic reactions.
According to this question, step 3 and 4 of the citric acid cycle involves an oxidation and decarboxylation reaction to produce 2 molecules of carbon dioxide (CO2) and a 4-carbon compound called succinyl group. A coenzyme A binds to the succinyl group to form succinyl-SCoA.
What would be the volume, in liters measured at STP, of 9.75 moles of carbon monoxide?
I
What is one service humans receive from the environment AND one-way humans disrupt ecosystems? (These need to be related!)
Answer:
Land-use change: Humans may destroy natural landscapes as they mine resources and urbanize areas. This is detrimental, as it displaces residing species, reducing available habitats and food sources. ... This can negatively effect an ecosystem because the introduced species may outcompete native organisms and displace them.
Explanation:
why dil. sulphuric acid cannot be used instead of dil.hcl in lab preparation of carbon dioxide gas?
Answer:
Because Sulphuric acid(H2SO4) is one of the substance which have a very high vigourous reaction if mix with chemicals thats why we take the same sulphuric acid but having lighter effects known to be as Dil.Sulphuric And so it is generally use for precaution while during experimentations Thats why we use it.
Hope it helps
Potassium hydroxide is partially soluble as shown by the
following reaction:
KOH(s) K+ (aq) + OH(aq)
What is the poH of a 3.32 x 10-5 M KOH solution?
pOH =
Your answer should be rounded to three significant figures. Do not Include
units in your answer.
Answer: 4.48 or 4.47
For many purposes, we can treat propane (C3H8) as an ideal gas at temperatures above its boiling point of -24C Suppose the temperature of a sample of propane gas is lowered from 14.0c to -1.0c and at the same time the pressure is changed.
If the initial pressure was0.75 kPa and the volume decreased by55.0% what is the final pressure? Round your answer to the correct number of significant digits.
it's 75 k bro thats the answer
- How much power does it take to lift a
1,000 N load 10 m in 20 s?
Answer:
"500 Joule/sec" is the right answer.
Explanation:
The given values are:
Force,
F = 1000 N
Velocity,
s = 10 m
Time,
t = 20 s
Now,
The power will be:
= [tex]\frac{Force\times Velocity}{Time}[/tex]
On putting the values, we get
= [tex]\frac{1000\times 10}{20}[/tex]
= [tex]\frac{10000}{20}[/tex]
= [tex]500 \ Joule/sec[/tex]
How do gas particles respond to an increase in volume?
When the volume of a gas is increased, the gas particles respond by spreading out and occupying a larger space. This results in a decrease in the density of the gas and a decrease in the frequency of collisions between the gas particles.
How do gas particles respond to an increase in volume?As the gas particles spread out, the pressure exerted by the gas decreases.
This is because the pressure of a gas is directly proportional to the number of collisions per unit area of the container walls. When the volume increases, the same number of gas particles are distributed over a larger area, reducing the frequency of collisions and thus decreasing the pressure.
In summary, an increase in volume causes gas particles to spread out, resulting in a decrease in density and a decrease in pressure.
Learn more about volume at
https://brainly.com/question/14197390
#SPJ6
moles of H2O are needed to exactly react with 2.0 moles of Ca
Answer:
4
Explanation:
so first write the balance equation
Ca+2H2O---->Ca(OH)2 + H2
then use molar ratio of H2O and Ca
which is 2:1 so if there are 2 moles of ca there will be 4 moles as you times it by 2. like this
Ca:H2O
1:2
2:4
Hope this helps u understand:)
How many iron atoms are in Fe2O3?
Answer:
2 iron atoms in Fe2O3
1. If 80.0 ml of 3.00 M HCl is used to make a 100. ml of dilute acid, what is the molarity
of new dilute HCl solution?
We are given:
M1 = 3 Molar V1 = 80 mL
M2 = x Molar V2 = 100 mL
Finding the molarity:
We know that:
M₁V₁ = M₂V₂
where V can be in any units
(3)(80) = (x)(100)
x = 240/100 [dividing both sides by 100]
x = 2.4 Molar
NO LINKS OR FILES
Using Ohm's Law and Watt's Law. write the formula to find each measurement
Wattage (Watts)
Resistance (Ohms)
Voltage (Volts)
and/or
Current (Amps)
and/or
Explanation:
Mathematically, Ohm's law is given by :
V = IR
Where
V is voltage
I is current
R is resistance
The electric power of an electrical appliance is given by:
P = VI
Wattage = VI
Resistance, [tex]R=\dfrac{V}{I}[/tex]
Current, [tex]I=\dfrac{V}{R}[/tex]
Hence, this is the required solution.
what is the mass of 0.200 mol of calcium
This unbalanced equation represents a chemical reaction:
Pb(NO3)2 + Nal NaNO3 + PbI2
What is the coefficient for Nal once the equation is balanced?
Α. 1
B. 2
C. 3
D. 4
Answer:
2
Explanation:
Pb(NO3)2 + 2NaI 2NaNO3 + PbI2
To see the coefficients of NaI in the given reaction we need to balance the reaction first. The coefficient for Nal once the equation is balanced is 2. the correct option is option B.
What is balanced equation?Balanced equation is the one where the number of atoms of each species is same on reactant and product side. In balanced equation mass can neither be created nor be destroyed.
The unbalanced equation is
[tex]\rm Pb(NO_{3})_{2}+ Nal\rightarrow NaNO_{3} + PbI_{2}[/tex]
The atoms of Pb on reactant and product side is 1 so Pb is balanced.
The atoms of N is 2 on reactant and 1 on product side so balance it as
[tex]\rm Pb(NO_{3})_{2}+ Nal\rightarrow 2 NaNO_{3} + PbI_{2}[/tex]
The atoms of O is 6 on reactant and 6 on product side so it is balanced
The atoms of I is 1 on reactant and 2 on product side so balance it as
[tex]\rm Pb(NO_{3})_{2}+2 Nal\rightarrow 2NaNO_{3} + PbI_{2}[/tex]
The atoms of Na on reactant and product side is 2 so Na is balanced.
Now all the elements are balanced
Therefore, the coefficient for Nal once the equation is balanced is 2. the correct option is option B.
Learn more about the balanced equations, here:
https://brainly.com/question/7181548
#SPJ2
Four satellites are in orbit around the Earth. The heights of their four orbits
are identical. The masses of the four satellites are given in the table. For
which satellite is the gravitational pull of Earth the strongest?
List and describe the four layers of the Earth.
Answer:
Crust- thinest layer; the part we live on
Mantle- just beneath the crust; consists of magma
Outer Core- liquid metal; super hot; thickest layer (i think)
Inner Core- solid metal; SUPER compressed; hottest layer