Answer:
pOH = 6.73
Explanation:
First, calculate pH = -log[H+] = -log(5.4 x 10^-8) = 7.27
pOH + pH = 14, so pOH = 14 - 7.27 = 6.73
When electrons lost a blank ion is formed
When electrons are gained a blank ion is formed
Answer:
I love it
Explanation:
☁️ Answer ☁️
annyeonghaseyo!
Your answer is:
When electrons are lost, a positively charged ion is formed. When electrons are gained, a negatively charged ion is formed. (I like the car)
Hope it helps.
Have a nice day noona/hyung!~ ￣▽￣❤️
What are resistors? please help
Answer:Resistor Basics
Resistors are electronic components which have a specific, never-changing electrical resistance. The resistor's resistance limits the flow of electrons through a circuit.
They are passive components, meaning they only consume power (and can't generate it). Resistors are usually added to circuits where they complement active components like op-amps, microcontrollers, and other integrated circuits. Commonly resistors are used to limit current, divide voltages, and pull-up I/O lines.
Resistor units
The electrical resistance of a resistor is measured in ohms. The symbol for an ohm is the greek capital-omega: Ω. The (somewhat roundabout) definition of 1Ω is the resistance between two points where 1 volt (1V) of applied potential energy will push 1 ampere (1A) of current.
As SI units go, larger or smaller values of ohms can be matched with a prefix like kilo-, mega-, or giga-, to make large values easier to read. It's very common to see resistors in the kilohm (kΩ) and megaohm (MΩ) range (much less common to see miliohm (mΩ) resistors). For example, a 4,700Ω resistor is equivalent to a 4.7kΩ resistor, and a 5,600,000Ω resistor can be written as 5,600kΩ or (more commonly as) 5.6MΩ.
Schematic symbol
All resistors have two terminals, one connection on each end of the resistor. When modeled on a schematic, a resistor will show up as one of these two symbols:
Resistor schematic symbols
Two common resistor schematic symbols. R1 is an American-style 1kΩ resistor, and R2 is an international-style 47kΩ resistor.
The terminals of the resistor are each of the lines extending from the squiggle (or rectangle). Those are what connect to the rest of the circuit.
The resistor circuit symbols are usually enhanced with both a resistance value and a name. The value, displayed in ohms, is obviously critical for both evaluating and actually constructing the circuit. The name of the resistor is usually an R preceding a number. Each resistor in a circuit should have a unique name/number. For example, here's a few resistors in action on a 555 timer circuit:
Answer: resistor is
Explanation:
A resistor controls the flow of the electrical current within a circuit. Resistors are made from materials like copper or carbon, which make it difficult for the electrical charges to flow through a circuit. The most common type of resistor is a carbon resistor, which is a general purpose resistor, best suited for lower-powered circuits.
Which particles make up most of the mass of an atom?
i think Neuterons i am right
Answer:
I do not know srry
Explanation:
what is phase change?
Explanation:
In chemistry, thermodynamics, and many other related fields, phase transitions (or phase changes) are the physical processes of transition between the basic states of matter: solid, liquid, and gas, as well as plasma in rare cases.
Answer:
In chemistry, thermodynamics, and many other related fields, phase transitions are the physical processes of transition between the basic states of matter: solid, liquid, and gas, as well as plasma in rare cases. A phase of a thermodynamic system and the states of matter have uniform physical properties.
Explanation:
Which of the following describes wind direction?
Wind direction is reported by the direction from which it originates. For example, a north or northerly wind blows from the north to the south. Wind direction is usually reported in cardinal (or compass) direction, or in degrees.
How do we know if molecules have kinetic energy?
Analyzing models compare an atom’s structure to a ladder. Identify one way in which ladder is not a good model from the atom.
Answer:
Climbing a ladder assumes that you would touch/use each step only once. Electrons will take one layer that is empty first, and previous layers or "steps" will continue being filled with additional electrons only when every other layer is occupied by, at least, one electron.
Explanation:
A good analogy is what passengers in a bus do. Everyone tries to sit alone first and only when every pair of seats has a person already seated, people will use them as well, sitting next to each other.
2.
You take a gas at 3 atm and increase the temperature from 120 K to 240 K. What is the final pressure?
A
6 atm
B
Not enough information
C
3 atm
D
1.5 atm
Answer:
A. 6atm
Explanation:
Using pressure law equation:
P1/T1 = P2/T2
Where;
P1 = initial pressure (atm)
T1 = initial temperature (K)
P2 = final pressure (atm)
T2 = final temperature (K)
According to this question;
P1 = 3 atm
P2 = ?
T1 = 120K
T2 = 240K
Using P1/T1 = P2/T2
3/120 = P2/240
Cross multiply
240 × 3 = P2 × 120
720 = 120P2
P2 = 720/120
P2 = 6atm
list the factor on which Ka of a weak acid depends
In what way is heat transferred to the tubes? (Hint “touching’”)
Please help
I will give you Brainliest
Answer:
in heat transfer, as the fluid flows along the tube, the wall layers are heated or cooled. temp. variation occurs in the wall layers.
good luck :)
i hope this helps
have a great day !!
In the electrolysis of molten lead bromide, what is the product at the anode?
Answer:
it is the second one. Lead
Gas in a balloon occupies 3.3 liters. What volume will it occupy if the pressure is changed from 100 kPa to 90.0 kPa, if the temperature is held constant?
Answer:
3.7 L
Explanation:
Initial volume (V₁) = 3.3 L
Initial pressure (P₁) = 100 KPa
Final pressure (P₂) = 90 KPa
Final volume (V₂) =?
The final volume of the gas can be obtained by using the Boyle's law equation as follow:
P₁V₁ = P₂V₂
100 × 3.3 = 90 × V₂
330 = 90 × V₂
Divide both side by 90
V₂ = 330 / 90
V₂ = 3.7 L
Thus, the final volume of the gas is 3.7 L
determine the velocity of a cart traveling at 135cm in 5.5s.
Answer: 0.245 m/s
Explanation:
So velocity = d/t or distance over time in this case m/s or meters per second. But BE CAREFUL you must remember to convert cm to m always so 135 cm= 1.35m and 1.35m/5.5s= 0.245m/s
Why does nobody fking answer my questions.
How did stromatolites contribute oxygen to the early atmosphere?
through methane degradation
through photolysis
by weathering of rocks
through photosynthesis
Answer:
by wearing of rocks
Explanation:
earths gravity your welcome
Answer:
weathering of rocks is the answer to your question
The number of ions produced when a substance dissolves is always equal to the number of Adams in a chemical formula. What is incorrect about following statement?
how many significant figures are in the measurement 12.4 kg
What causes lava to not instantly melt ice sheets when it is poured onto it?
Answer:
Dry ice
Explanation:
Answer:
The lava doesn't melt through ice because the steam ice sits on top of a blanket of steam rather than on top of the ice itself. This means the friction between the lava and the ice is very low.
Explanation:
A woman uses 330 Joules of energy to push a box across the floor in 33 seconds. What is her power output in Watts?
Answer:
10 watts
Explanation:
Power = Work / Time
Power = 330 J / 33 s
Power = 10 watts
Question 7 of 10
The Sun has a diameter of about 865,000 miles.
Suppose you were making a scale model of the
solar system with a scale of 1 inch:1,000 miles.
How wide would the Sun be in your model?
A. 865,000 inches
B. 865 inches
C. 86.5 inches
O D. 8.65 inches
Answer:
you have to decide 865,000 with 1000 and the answer is 865
Students report that the sky in their area has mostly cirrus clouds. What are most likely the weather conditions in the area?
rainy weather
dark, overcast (blocking the sunlight)
stormy weather
fair, pleasant weather
What element is in group 4 and period 3
How many copies of DNA do haploid cells have
Answer:
2 lol
Explanation:
- A compound contains 4.56g. of Pb, 2.3g Cl, and 3.1g 0. What is the percent
composition for each element?
please show work
1. The chemical formula of caffeine is C8H10N4O2. Determine the percent composition of the molecule.
Show work please
Answer:
we find the mass for each element in one mole by multiplying the number of atoms in one molecule with the atomic mass
mC=8Ac=8*12=96g
mH=10AH=10*1=10g
mN=4AN=4*14=56g
mO=2AO=2*16=32g
by adding the masses together we find the molar mass of the molecule
M=mC+nH+mN+mO=96+10+56+32=194g/mole
we apply the rule of threes to find the percentage of each element
194g..96gC..10gH...56gN....32gO
100g....a...........b...........c.............d
a=(100*96)/194=49.48%C
b=(100*10)/194=5.19%H
c=(100*56)/194=28.85%N
d=(100*32)/194=16.48%O
Explanation:
In a chemical reaction between copper metal and silver nitrate, 12.7 g of copper(II) and 64.5 g of silver nitrate react, and 38.1 g of Silver is produced. 21) Predict the products and write the balanced equation and include the physical state of each. 22) What type of chemical reaction is this? 23) Which is the limiting reactant? You must include the work for this to receive full credit. 24) What mass of excess is used up, and what mass is left over? 25) Calculate the percent yield.
Answer:What should you do if you realize during research that your original theory is wrong
Explanation:
Why does a DNA fingerprint require millions of copies of each DNA fragment
Answer:
Because it can identify a person.
A DNA fingerprint is a piece of DNA so distinct that it can prove a person's identity. These distinct areas can take on many different forms, but each form is unique to any one individual.
PCR allows the amplification of a single copy of DNA into millions of copies. However this technique requires that the DNA of interest already be of a known sequence in order to design primers that will specifically hybridize to the target DNA.
It is important as:
It's used as evidence in courts, to identify bodies, track down blood relatives, and to look for cures for disease.
Learn more:
brainly.com/question/13695548
An object was measured by a worker as 35.6 cm long, however, the manufacturer specifications list the length of the object at 35.0 cm. What is the percent error in the workers measurement?
complete the bolded items in each box below
Show the bolded items and the boxes.
Am I doing this right?
What is [OH-] of a solution
with a pH of 4.0?
Answer in M
What kind of reaction is 2H202 → 2H20 + O2?
O A. Decomposition
O B. Single-replacement
C. Double-replacement
O D. Synthesis
Answer:
this reaction is so the answer should be A