To determine the feeder size for a 100 Amp single-phase feeder at the load side of a 120/240 V load center, follow these steps:
Calculate the load demand in amperes based on the connected load.
Apply the appropriate derating factors to account for various factors such as ambient temperature and conductor bundling.
Select the feeder size based on the calculated load demand and derating factors.
To determine the feeder size for a 100 Amp single-phase feeder, we need to calculate the load demand based on the connected load. This involves assessing the total power consumption of the connected devices and converting it to an amperage value. For example, if the connected load requires 80 Amps, we would need a feeder capable of carrying at least 80 Amps of current.
In the next step, we apply derating factors to account for various factors that can affect the performance of the feeder. These factors include ambient temperature, conductor bundling, and voltage drop considerations.
Derating factors ensure that the feeder is capable of handling the load under different operating conditions. It is crucial to consult local electrical codes and standards to determine the appropriate derating factors to use.
Based on the calculated load demand and the applied derating factors, we can select the appropriate feeder size. Feeder sizes are standardized and typically available in predetermined amperage ratings. We would select a feeder size that is equal to or larger than the calculated load demand, ensuring that it can safely carry the required current without exceeding its rated capacity.
Learn more about Various factors
brainly.com/question/13261403
#SPJ11
QUESTION 13 Which of the followings is true? O A. Electrical components are typically not deployed under wireless systems as transmissions are always through the air channel. O B. Complex conjugating is a process of keeping the real part and changing the complex part. C. Adding a pair of complex conjugates gives the real part. O D. Adding a pair of complex conjugates gives double the real part.
Option C is true. Adding a pair of complex conjugates gives the real part. Complex conjugation is an operation performed on a complex number, where the sign of the imaginary part is changed.
It involves negating the imaginary component while keeping the real component unchanged. The result is a new complex number known as the complex conjugate. When we add a pair of complex conjugates, the imaginary parts cancel each other out because they have opposite signs. As a result, only the real parts remain, and their sum gives the real part of the complex conjugate pair. Option C states that adding a pair of complex conjugates gives the real part. This is true because the cancellation of imaginary parts leads to the elimination of the complex component, leaving only the real part. Options A, B, and D are not true in this case. Option A is incorrect because electrical components can be used in wireless systems, and transmissions are not exclusively limited to the air channel. Option B is incorrect because complex conjugation involves changing the sign of the imaginary part, not keeping the real part unchanged. Option D is incorrect because adding a pair of complex conjugates does not yield double the real part, but rather the real part itself.
learn more about complex here :
https://brainly.com/question/31836111
#SPJ11
Identify the following Cloud computing services that provide virtual machines, hardware and operating systems which may be controlled through a service API.
Software-as-a-Service (SaaS)
Platform-as-a-Service (PaaS)
Infrastructure-as-a-Service (IaaS)
None of the above
The Cloud computing services that provide virtual machines, hardware and operating systems which may be controlled through a service API:
Infrastructure-as-a-Service (IaaS).
IaaS is a type of cloud computing service that provides virtual machines, hardware, and operating systems, which can be managed through a service API. IaaS allows organizations to manage and control their own infrastructure while outsourcing the maintenance and support of the underlying hardware and software infrastructure.
Therefore, the correct option is "Infrastructure-as-a-Service (IaaS)".
Learn more about cloud computing: https://brainly.com/question/26972068
#SPJ11
An adiabatic closed system is accelerated from 10 m/s to 40 m/s. Determine the specific energy change of this system, in kJ/kg.
The specific energy change of the adiabatic closed system, accelerated from 10 m/s to 40 m/s, can be determined by calculating the difference in specific kinetic energy between the initial and final states.
Specific kinetic energy is given by the equation: KE = (1/2) * V^2, where V is the velocity.
For the initial state, the specific kinetic energy is (1/2) * 10^2 = 50 J/kg.
For the final state, the specific kinetic energy is (1/2) * 40^2 = 800 J/kg.
The specific energy change is the difference between the final and initial specific kinetic energies: 800 J/kg - 50 J/kg = 750 J/kg.
Converting the result to kilojoules: 750 J/kg = 0.75 kJ/kg.
Therefore, the specific energy change of the system is 0.75 kJ/kg.
Learn more about Specific energy
brainly.com/question/27920432
#SPJ11
A unidirectional carbon fiber ply has the stiffness components Q'1111=180 GPa, Q'2222=10 GPa, Q'1122=3 GPa, Q'1212=7 GPa. Calculate the average stress in the plate (in the x1-x2 coordinate system), as well as the stresses in the individual plies in a coordinate system aligned with the orthotropy axes, in a plate of length L=2 m in the x1-direction, width w=0.5 m in the x2-direction, thickness h=1 mm, with the layup (+30,-30)s, subjected to a load of 100,000 N in the x1-direction applied on the short edges.
The average stress in the plate in the x1-x2 coordinate system is 3.85 MPa. The maximum stress is 6.33 MPa, which occurs in the ply oriented at 30 degrees.
Given stiffness components:
Q'1111=180 GPa, Q'2222=10 GPa,
Q'1122=3 GPa, Q'1212=7 GPa
The laminate layup is (+30,-30)sLength,
L = 2 mWidth,
w = 0.5 mThickness,
h = 1 mmLoad,
P = 100,000 N in the x1-direction applied on the short edges.
The stresses are calculated using the following equations:σ_avg = [Q'] [ε_avg]σ_i = [Q_i] [ε_i] where [Q'] is the global stiffness matrix, [Q_i] is the stiffness matrix of the i-th ply,
[ε_avg] is the average strain in the plate, and [ε_i] is the strain in the i-th ply.
The strains are calculated using the following equations:ε_avg = [S] [ε]_iε_i = [S_i] [ε]_iwhere [S] is the compliance matrix of the plate, [S_i] is the compliance matrix of the i-th ply, and [ε]_i is the strain in the x1-x2 coordinate system.
The average strain in the plate isε_avg = [1/2ε_x1, 1/2ε_x2, 0]Twhere ε_x1 = P / (h w Q'1111) = 3.086 × 10^-4ε_x2 = 0Therefore, ε_avg = [1.543 × 10^-4, 0, 0]T
The global stiffness matrix is[Q'] = [Q]swhere [Q] is the stiffness matrix of a single ply in the x1-x2 coordinate system, and s is the stacking sequence matrix.[Q] = [Q']_x' [T] [Q']_xwhere [Q']_x' is the stiffness matrix of a single ply in the orthotropic coordinate system,
[T] is the transformation matrix from the orthotropic coordinate system to the x1-x2 coordinate system, and [Q']_x is the stiffness matrix of a single ply in the x1-x2 coordinate system.
[Q']_x' is given by[Q']_x' = [1 / Q'1111 -Q'1122 / Q'1111 0][0 1 / Q'2222 0][0 0 1 / Q'1212]
The transformation matrix is
[T] = [cos30 -sin30 0][sin30 cos30 0][0 0 1]
The stiffness matrix in the x1-x2 coordinate system is [Q']_x = [9.102 -2.903 0][-2.903 1.706 0][0 0 7.324]
The stacking sequence matrix iss = [+30 -30]T
Therefore, the global stiffness matrix is[Q'] = [9.102 -2.903 0][-2.903 1.706 0][0 0 7.324]
The stress in the plate isσ_avg = [Q'] [ε_avg] = [3.85 0 0]T
The stress in each ply isσ_i = [Q_i] [ε_i]where[ε_i] = [S_i]^-1 [ε_avg] = [T]^-1 [S]^-1 [T_i] [ε_avg]
The compliance matrix of each ply is[S_i] = [Q_i]^-1
The transformation matrix from the orthotropic coordinate system to the i-th ply coordinate system is
[T_i] = [cos30 -sin30 0][sin30 cos30 0][0 0 1] [cosθ -sinθ 0][sinθ cosθ 0][0 0 1][cos(-30) -sin(-30) 0][sin(-30) cos(-30) 0][0 0 1]where θ is the orientation angle of the i-th ply relative to the x1-axis.
For the (+30,-30)s layup, the angles are 30 degrees and -30 degrees.
Therefore,[T_1] = [0.75 -0.433 0][0.433 0.75 0][0 0 1][0.75 0.433 0][-0.433 0.75 0][0 0 1][0.75 -0.433 0][0.433 0.75 0][0 0 1]
The stiffness matrices of each ply in the x1-x2 coordinate system are
[Q_1] = [9.102 -2.903 0][-2.903 1.706 0][0 0 7.324][Q_2] = [9.102 2.903 0][2.903 1.706 0][0 0 7.324]
The strains in each ply are
[ε_1] = [0.0106 -0.0034 0]T[ε_2] = [-0.0106 -0.0034 0]T
The stresses in each ply areσ_1 = [70.99 -22.69 0]Tσ_2 = [-73.31 22.69 0]T
The maximum stress is 6.33 MPa, which occurs in the ply oriented at 30 degrees.
To learn more abou stress
https://brainly.com/question/30263693
#SPJ11
Which of the following statements is true for a mechanical energy reservoir (MER)? O stores work as KE or PE O all of the mentioned O all processes within an MER are quasi-static O it is a large body enclosed by an adiabatic impermeable wall
The statement "O all of the mentioned" is true for a mechanical energy reservoir (MER).
A mechanical energy reservoir is a system that stores mechanical energy in various forms such as kinetic energy (KE) or potential energy (PE). It acts as a source or sink of energy for mechanical processes.
In an MER, all processes are typically assumed to be quasi-static. Quasi-static processes are slow and occur in equilibrium, allowing the system to continuously adjust to external changes. This assumption simplifies the analysis and allows for the application of concepts like work and energy.
Lastly, an MER can be visualized as a large body enclosed by an adiabatic impermeable wall. This means that it does not exchange heat with its surroundings (adiabatic) and does not allow the transfer of mass across its boundaries (impermeable).
Therefore, all of the mentioned statements are true for a mechanical energy reservoir.
Learn more about mechanical energy here:
brainly.com/question/30853813
#SPJ11
In your house, you have an electrical heater to heat 10 liter water from 0°C to 100 °C The energy required to heat 1 g of water from 0°C to 100 °C = 100 calories 1 kcal = 4186 J, 1 kWh = 3.16* 10 Joule, 1000 g of water = 1 liter of water. 1) what is the ideal energy required to heat 10 liter from 0°C to 100 °C in kWh.? 2) if the electric meter reading is 1.5 kWh, what is the efficiency of this heater. 3) if the cost of electricity is 0.12 JD for 1 kWh, what will be the cost of heating 10 liters water in Jordanian Dinar?
The ideal energy required to heat 10 liters of water from 0°C to 100°C is approximately 418.6 kWh,the cost of heating 10 liters of water in Jordanian Dinar would be approximately 50.23 JD, considering the electricity cost of 0.12 JD per kWh.
To calculate the ideal energy required to heat 10 liters of water from 0°C to 100°C, we need to consider that 1 liter of water is equal to 1000 grams. Therefore, the total mass of water is 10,000 grams. The energy required to heat 1 gram of water by 1°C is 1 calorie. Since the temperature difference is 100°C, the total energy required is 10,000 grams * 100 calories = 1,000,000 calories. Converting this to kilowatt-hours (kWh), we divide by 3.6 million (the number of joules in a calorie) to get approximately 418.6 kWh.
The efficiency of the heater is determined by the ratio of useful output energy (energy used to heat the water) to total input energy (electricity consumed). In this case, the useful output energy is 418.6 kWh (as calculated in the previous step), and the total input energy is given as 1.5 kWh. Dividing the useful output energy by the total input energy and multiplying by 100 gives us the efficiency: (418.6 kWh / 1.5 kWh) * 100 = approximately 66.5%.
To calculate the cost of heating 10 liters of water, we multiply the total energy consumption (418.6 kWh) by the cost per kilowatt-hour (0.12 JD/kWh). Multiplying these values gives us the cost in Jordanian Dinar: 418.6 kWh * 0.12 JD/kWh = approximately 50.23 JD.
Learn more about Jordanian Dinar
brainly.com/question/14190652
#SPJ11
Draw the T-type equivalent circuit of transformer, and mark the components in the circuit by R₁, X₁, R₂, X, Rm and Xm. Which symbol stands for the magnetization reactance? Which symbol stands for the primary leakage reactance? Which symbol is the equivalent resistance for the iron loss? Which symbol is the secondary resistance referred to the primary side? (6 marks).
The T-type equivalent circuit of a transformer consists of four components namely R1, X1, R2 and X2 that represent the equivalent resistance and leakage reactance of the primary and secondary winding, respectively
Symbol stands for the magnetization reactance: Xm
symbol stands for the primary leakage reactance: X1
Symbol is the equivalent resistance for the iron loss: Rm
Symbol is the secondary resistance referred to the primary side: R2T
herefore, the above mentioned circuit is called the T-type equivalent circuit of a transformer. In this circuit, R1 is the resistance of the primary winding,
X1 is the leakage reactance of the primary winding, R2 is the resistance of the secondary winding, and X2 is the leakage reactance of the secondary winding.
The equivalent resistance for the core losses is represented by Rm.
The magnetization reactance is represented by Xs. The primary leakage reactance is represented by X1.
The secondary resistance referred to the primary side is represented by R2.
Know more about the transformer
https://brainly.com/question/32265938
#SPJ11
Name the eight key elements recommended for an Ergonomics Program as presented in the OSHA Meatpacking Guidelines?
The OSHA Meatpacking Guidelines recommend the following eight key elements for an Ergonomics Program in the meatpacking industry:
These key elements are designed to help prevent and mitigate ergonomic hazards in the meatpacking industry, reducing the risk of work-related injuries and promoting a safer working environment for employees.
Management Commitment and Employee Involvement: Management should demonstrate a commitment to ergonomics by allocating resources, establishing policies, and involving employees in the decision-making processWorksite Analysis: Conduct a thorough analysis of the worksite to identify ergonomic risk factors, such as repetitive motions, awkward postures, and heavy lifting.
Hazard Prevention and Control: Implement measures to prevent and control ergonomic hazards, including engineering controls, administrative controls, and personal protective equipment (PPE). Training: Provide training to employees on ergonomics awareness, hazard recognition, and safe work practices to minimize the risk of musculoskeletal disorders (MSDs).
Medical Management: Develop protocols for early detection and management of work-related MSDs, including prompt reporting, medical evaluation, treatment, and rehabilitation.
Program Evaluation: Regularly assess the effectiveness of the ergonomics program, identify areas for improvement, and make necessary adjustments.Recordkeeping and Program Documentation: Maintain records related to ergonomics program activities, including assessments, training, incident reports, and corrective actions.
Management Review: Conduct periodic reviews of the ergonomics program to ensure its continued effectiveness and make any necessary updates or revisions.
These key elements are designed to help prevent and mitigate ergonomic hazards in the meatpacking industry, reducing the risk of work-related injuries and promoting a safer working environment for employees.
Learn more about Ergonomics here
https://brainly.com/question/28706393
#SPJ11
3. How the stress-strain curve of materials is
influenced by Z value?
please send it necessary
The Z value is a fundamental atomic property, it does not directly influence the stress-strain curve of materials. The mechanical behavior of materials is governed by various other factors related to their composition, structure, and defects.
The stress-strain curve of materials is not directly influenced by the Z value. The Z value, also known as the atomic number or atomic mass, is a property of individual atoms and is related to the number of protons or the total number of nucleons in an atom's nucleus. It does not directly impact the mechanical behavior of materials. The stress-strain curve of a material is influenced by its inherent properties, such as the type of material, crystal structure, defects, and microstructure. These factors determine the material's response to external forces and deformation. The stress-strain curve typically consists of several regions, including the elastic region, yield point, plastic deformation region, and fracture point. The curve provides information about the material's stiffness, strength, and ductility. To analyze and understand the mechanical behavior of a specific material, other properties such as Young's modulus, yield strength, ultimate tensile strength, and elongation are considered. These properties are determined by factors such as the atomic bonding, crystal lattice structure, and dislocation motion within the material.
Learn more about the stress-strain curve here:
brainly.com/question/32770414
#SPJ11
Develop a minimum-multiplier realization of a length-7 Type 3 Linear Phase FIR Filter.
A minimum-multiplier realization of a length-7 Type 3 Linear Phase FIR Filter can be developed.
To develop a minimum-multiplier realization of a length-7 Type 3 Linear Phase FIR Filter, we need to understand the key components and design considerations involved. A Type 3 Linear Phase FIR Filter is characterized by its linear phase response, which means that all frequency components of the input signal experience the same constant delay. The minimum-multiplier realization aims to minimize the number of multipliers required in the filter implementation, leading to a more efficient design.
In this case, we have a length-7 filter, which implies that the filter has 7 taps or coefficients. Each tap represents a specific weight or gain applied to a delayed version of the input signal. To achieve a minimum-multiplier realization, we can exploit the symmetry properties of the filter coefficients.
By carefully analyzing the symmetry properties, we can design a structure that reduces the number of required multipliers. For a length-7 Type 3 Linear Phase FIR Filter, the minimum-multiplier realization can be achieved by utilizing symmetric and anti-symmetric coefficients. The symmetric coefficients have the same value at equal distances from the center tap, while the anti-symmetric coefficients have opposite values at equal distances from the center tap.
By taking advantage of these symmetries, we can effectively reduce the number of multipliers needed to implement the filter. This results in a more efficient and resource-friendly design.
Learn more about multiplier
brainly.com/question/31406180
#SPJ11
Air at temperature of 50°C db, 80% relative humidity and a pressure of 100 kPa undergoes a throttling process to a pressure of 90 kPa. Calculate the specific humidity at the final equilibrium state. Assume that air and water vapor behave like ideal gases.
The specific humidity at the final equilibrium state is calculated using the given conditions and the ideal gas law.
What is the specific humidity at the final equilibrium state after throttling air from 100 kPa to 90 kPa with initial conditions of 50°C dry bulb temperature and 80% relative humidity?To calculate the specific humidity at the final equilibrium state after the throttling process, we can use the concept of the psychrometric chart.
Given:
Initial temperature (T1) = 50°C
Relative humidity (RH) = 80%
Initial pressure (P1) = 100 kPa
Final pressure (P2) = 90 kPa
1. Find the saturation vapor pressure at T1:
Using the psychrometric chart or equations, find the saturation vapor pressure (Psat) at 50°C. Let's assume it to be Psat1.
2. Find the vapor pressure at T1:
The vapor pressure (Pv1) can be calculated using the equation:
Pv1 = (RH/100) * Psat1
3. Find the dry air pressure at T1:
Pdry1 = P1 - Pv1
4. Find the specific humidity at T1:
The specific humidity (ω1) can be calculated using the equation:
ω1 = (0.622 * Pv1) / (Pdry1 - 0.378 * Pv1)
5. Use the ideal gas law to find the final temperature (T2):
Using the ideal gas law, we have:
(P1 * V1) / T1 = (P2 * V2) / T2
where V1 and V2 represent the specific volumes of dry air at the initial and final states, respectively.
6. Find the saturation vapor pressure at T2:
Using the psychrometric chart or equations, find the saturation vapor pressure (Psat) at the final temperature T2. Let's assume it to be Psat2.
7. Find the vapor pressure at T2:
The vapor pressure (Pv2) can be calculated using the equation:
Pv2 = (P2 * ω1 * Pdry1) / ((0.622 * ω1) + 0.378)
8. Find the specific humidity at the final equilibrium state:
The specific humidity (ω2) at the final state is given by:
ω2 = (0.622 * Pv2) / (P2 - 0.378 * Pv2)
Calculate ω2 using the obtained values of Pv2 and P2 to get the specific humidity at the final equilibrium state.
Learn more about equilibrium
brainly.com/question/30694482
#SPJ11
A fluid is said to be ideal, if it is (a) incompressible (b)
inviscous (c) viscous and incompressible (d) inviscous and
compressible (e) inviscous and incompressible.
The correct answer is (e) inviscous and incompressible. An ideal fluid is one that is both inviscous (having no internal friction or viscosity) and incompressible (maintaining a constant density regardless of pressure changes).
Inviscosity implies that the fluid flows without any resistance, while incompressibility means that its density remains constant under different pressure conditions. These characteristics simplify the mathematical modeling of ideal fluids, allowing for the use of simpler equations such as the Bernoulli's equation in fluid dynamics. While real fluids may not perfectly exhibit these properties, ideal fluid assumptions are often employed in theoretical analysis and engineering approximations.
Learn more about internal friction here:
https://brainly.com/question/30136439
#SPJ11
True or False: Write T for True and F for False only. The delta configuration is commonly used in SOURCE side. True or False: Write T for True and F for False only. The wye configuration is commonly used in SOURCE side.
The delta connection is commonly used in DISTRIBUTION systems, not source side. The delta (Δ) configuration is also called as the mesh or closed delta. It is called mesh as it forms a closed loop which looks similar to a fishnet or mesh or net. This closed delta arrangement is usually used in transformer windings and motor windings. Hence, the given statement is false.
The wye (Y) configuration is also called a star or connected to ground. It is called connected to ground as it usually has the neutral point connected to ground. This wye arrangement is used in the transformer and generator windings. Hence, the given statement is true.
Learn more about delta configuration at
https://brainly.com/question/32659172
#SPJ11
In which situation, BJT npn transistor operates as a good amplifier? E. 0.68 V A. Vas Reverse bias and Ve Reverse bas B. Var Forward bias and Vac Forward bas C. Vas Forward bias and Vic Reverse bas D. Vas Reverse bias and Vic Forward bas E. All of them because it depends only on the value of le
Among the options provided, the situation in which a BJT (npn transistor) operates as a good amplifier is Var forward bias and Vac forward bias. Hence option B is correct.
In this configuration, the base-emitter junction (Var) is forward biased, allowing a small input signal to control a larger output signal. The base-collector junction (Vac) is also forward biased, providing proper biasing conditions for amplification.
Options A, C, and D involve reverse biasing of either the base-emitter junction (Vas) or the base-collector junction (Vic), which hinders the transistor's amplification capabilities.
Option E states that all situations can result in good amplification, depending only on the value of le. However, this statement is not accurate as the biasing conditions play a crucial role in determining the transistor's amplification performance.
Learn more about npn transistor here:
brainly.com/question/31730979
#SPJ4
8. Write and execute a query that will delete all countries that are not assigned to an office or a client. You must do this in a single query to receive credit for this question. Write the delete query below and then execute the following statement in SQL Server: Select * from Countries. Take a screenshot of your select query results and paste them below your delete query that you constructed.
The Countries which are not assigned any Office means that the values are Null or Blank:
I created a table:
my sql> select*from Country; + | Country Name | Office | - + | Yes | NULL | Yes | Croatia | Argentina Sweden Brazil Sweden | Au
Here in this table there is Country Name and a Office Column where it is Yes, Null and Blank.
So, we need to delete the Blank and Null values as these means that there are no office assigned to those countries.
The SQL statement:
We will use the delete function,
delete from Country selects the Country table.
where Office is Null or Office = ' ' ,checks for values in Office column which are Null or Blank and deletes it.
Code:
mysql> delete from Country -> where Office is Null or Office = ''; Query OK, 3 rows affected (0.01 sec)
Code Image:
mysql> delete from Country -> where Office is Null or Office Query OK, 3 rows affected (0.01 sec) =
Output:
mysql> select*from Country; + | Country Name | Office | + | Croatia Sweden Sweden | India | Yes | Yes Yes | Yes + 4 rows in s
You can see that all the countries with Null and Blank values are deleted
A reversible refrigeration cycle operates between cold and hot thermal reserviors at 28 °C and 35 °C, respectively. The coefficience of performance is closely A 1.5 B 4.0 C 2.82 D 43.02
The coefficient of performance of a reversible refrigeration cycle operating between cold and hot thermal reservoirs at 28 °C and 35 °C, respectively, is closely 2.82. Option (C) is correct.
Coefficient of performance is the ratio of the amount of heat absorbed from the cold reservoir (QC) to the amount of work done to accomplish this transfer of heat.
The formula to calculate the coefficient of performance (COP) is given by: COP = QC / W
Here, QC = Heat absorbed from cold reservoir
W = Work done
In this problem, the coefficient of performance is given as: COP = QC / W
And, the temperatures of the cold and hot thermal reservoirs are given as:
T1 = 28 °C (cold reservoir)T2 = 35 °C (hot reservoir)
Now, let's find the expression for COP in terms of T1 and T2.
The expression for the work done (W) is given as:
W = QC (1 - T1 / T2)
Substituting the value of W in the formula of COP, we get:
COP = QC / W= QC / (QC (1 - T1 / T2))= 1 / (1 - T1 / T2)
Now, substituting the values of T1 and T2, we get:
COP = 1 / (1 - 28 / 35)= 1 / (7 / 35 - 28 / 35)= 1 / (- 21 / 35)= - 35 / 21= - 1.6666...
Since COP cannot be negative, we take the absolute value of COP.
Therefore, the coefficient of performance is closely 2.82
Know more about coefficient of performance:
https://brainly.com/question/28175149
#SPJ11
A fuel oil is burned with air in a boiler furnace. The combustion produces 813 kW of thermal energy, of which 65% is transferred as heat to a boiler tubes that pass through the furnace. The combustion products pass from the furnace to a stack at 650°C. Water enters the boiler tubes as a liquid at 20 °C and leaves the tubes as saturated steam at 20 bar absolute a. Define the system. What type of energy balance is needed? Calculate the rate (kg/hr) at which steam is produced.
Fuel oil burned in boiler furnace Thermal energy produced by combustion = 813 kW Percentage of heat transferred = 65% Temperature of combustion products passing from furnace to stack = 650°C Water enters boiler tubes as a liquid at 20°C Water leaves the tubes as saturated steam at 20 bar absolute. Hence Steam is generated at a rate of 236.89 kg/hr.
According to the given data, the system here is the boiler, the fuel oil, and the combustion air.Type of energy balance:According to the given data, a steady-state energy balance can be applied to the given data.Calculate the rate at which steam is produced:First, we calculate the rate at which heat is transferred from combustion to the boiler tubes. Q1 = Q2 + Q3 Q1 is the heat produced by combustion Q2 is the heat transferred to the boiler tubes Q3 is the heat transferred to the surroundings by the combustion products Q2 = Q1 × percentage of heat transferred Q2 = 813 × 0.65 Q2 = 528.45 kW Cooling water flows at 30 °C and leaves at 80 °C.
We know that the rate of flow of cooling water is 72.4 kg/s and the specific heat capacity of water is 4.18 kJ/kg·°C.The heat transferred to cooling water can be calculated as: Q3 = mass flow rate of cooling water × specific heat capacity of water × (final temperature of water – initial temperature of water)Q3 = 72.4 × 4.18 × (80 − 30)Q3 = 157883.2 J/s This value must be converted to kW, which is the unit of power used in this problem. Q3 = 157883.2/1000Q3 = 157.88 kW Rate of steam production can be calculated as: Q2 = msteam × hfg where hfg is the specific enthalpy of vaporizationQ2 = mass of steam produced per unit time × specific enthalpy of vaporization Mass of steam produced per unit time = Q2/hfg Mass of steam produced per unit time = 528.45 × 1000/2227 Mass of steam produced per unit time = 236.89 kg/hr.
Therefore, the rate at which steam is produced is 236.89 kg/hr.
To learn more about "Thermal Energy" visit: https://brainly.com/question/19666326
#SPJ11
A 15 mm diameter steel bar has a forged surface with the ultimate strength Su = 1100 MPa and the yield strength Sy = 715 MPa. a) Esti- mate the S-N curve and the family of constant life fatigue curves for axial load. Estimate the fatigue life for 4x10⁵ cycles. b) Determine the fatigue strength corresponding to 10⁶ cycles and to 4x10⁴ cycles for the case of zero- to-maximum (rather than completely reversed) load fluctuations for bending and no yielding
a) The estimated fatigue life for 4x10⁵ cycles under axial load is approximately 179,260 cycles, based on the given ultimate strength (Su) and yield strength (Sy) of the steel bar.
b) In the case of zero-to-maximum load fluctuations in bending and no yielding, the fatigue strength remains constant regardless of the number of cycles and is equal to the yield strength (Sy) of the steel bar, which is 715 MPa.
a) To estimate the S-N curve and the family of constant life fatigue curves for axial load, we can use the Basquin's equation, which relates the stress amplitude (Sa) and the number of cycles to failure (Nf).
The equation can be written as:
[tex]Sa = C\times(Nf)^(^-^b^)[/tex]
Where:
Sa is the stress amplitude,
Nf is the number of cycles to failure,
C and b are material constants.
To estimate the S-N curve, we need to determine the values of C and b.
C is related to the ultimate strength and b is related to the slope of the S-N curve.
Assuming a typical value for b in the range of 0.1 to 0.2, we can estimate C using the Su value:
[tex]C = Su / (4 \times 10^(^-^b^))[/tex]
Substituting the given values:
Su = 1100 MPa
Assuming b = 0.15:
To estimate the fatigue life for 4x10⁵ cycles, we can rearrange the Basquin's equation to solve for Nf:
[tex]Nf = (Sa / C)^(^-^1^/^b^)[/tex]
Substituting Sa = Sy (yield strength):
[tex]Nf = (Sy / C)^(^-^1^/^b^)[/tex]
=[tex](715 MPa / C)^(^-^1^/^0^.^1^5^)[/tex]
[tex]Nf = (715 MPa / 871.78 MPa)^(^-^1^/^0^.^1^5^)[/tex]
Nf = 179,260 cycles
b)
The Goodman equation relates the alternating stress (Sa) and the mean stress (Sm) to the yield strength (Sy) and the ultimate strength (Su):
(Sa / Sy) + (Sm / Su) = 1
Rearranging the equation, we can solve for Sa:
Sa = Sy × (1 - Sm / Su)
For 10⁶ cycles:
Sa = Sy × (1 - Sm / Su)
Substituting Sm = 0 (zero mean stress):
Sa = Sy
For 4x10⁴ cycles:
Sa = Sy × (1 - Sm / Su)
Substituting Sm = 0 (zero mean stress):
Sa = Sy
Sy = 715 MPa.
To learn more on Fatigue strength click:
https://brainly.com/question/29990152
#SPJ4
The step down chopper is operating at 1 kHz. Other data are V = 240 V, L = 10 mH, R = 10 and duty cycle 60%. (a) current. Determine the DC component of the load current and the peak-to-peak ripple in the load (b) By how much will the above values change if the frequency is increased to 2 kHz other data remaining the same. (c) What will the change in the values determined in (a) if the frequency is unchanged but the inductance value is increased to 20 mH, other data remaining the same.
Changes in values if inductance is increased to 20 mH: Recalculate I_avg and I_ripple using new inductance.
Calculate the DC component of the load current and the peak-to-peak ripple in the load for a step-down chopper operating at 1 kHz with given data (V = 240 V, L = 10 mH, R = 10, duty cycle = 60%). Determine the changes in these values if the frequency is increased to 2 kHz or the inductance is increased to 20 mH.To determine the DC component of the load current and the peak-to-peak ripple in the load:
Calculate the inductor current during the on-time of the chopper:
I_Lon = (V * Ton) / L, where V is the input voltage, Ton is the on-time, and L is the inductance.Given V = 240 V, L = 10 mH, and duty cycle = 60% (Ton = 0.6 * T, where T is the switching period).Calculate the inductor current during the off-time of the chopper:
I_Loff = I_Lon * (1 - duty cycle) = I_Lon * (1 - 0.6).Calculate the average load current (DC component):
I_avg = I_Lon * duty cycle + I_Loff * (1 - duty cycle).Calculate the peak-to-peak ripple in the load current:
I_ripple = I_Lon - I_Loff.If the frequency is increased to 2 kHz:
Calculate the new on-time:
Ton_new = Ton * (f_new / f_old) = Ton * (2 kHz / 1 kHz).Repeat steps 1-4 from part (a) using the new on-time value.
If the inductance value is increased to 20 mH:Repeat steps 1-4 from part (a) using the new inductance value of 20 mH.
Please note that for accurate calculations, the units must be consistent (e.g., convert mH to H).
Learn more about Recalculate
brainly.com/question/30403734
#SPJ11
An exhaust fan, of mass 140 kg and operating speed of 900rpm, produces a repeated force of 30,500 N on its rigid base. If the maximum force transmutted to the base is to be limited to 6500 N using an undamped isolator, determine: (a) the maximum permissible stiffress of the isolator that serves the purpose, and (b) the steady state amplitude of the exhaust fan with the isolator that has the maximum permissible stiffness.
(a) The maximum permissible stiffness of the isolator is 184,294.15 N/mm.
(b) The steady-state amplitude of the exhaust fan with the isolator that has the maximum permissible stiffness is 0.18 mm.
(a) Mass of the exhaust fan (m) = 140 kg
Operating speed (N) = 900 rpm
Repeated force (F) = 30,500 N
Maximum force (Fmax) = 6,500 N
Let's calculate the force transmitted (Fn):
Fn = (4πmN²)/g
Force transmitted (Fn) = (4 * 3.14 * 140 * 900 * 900) / 9.8Fn = 33,127.02 N
As we know that the maximum force transmitted to the base is to be limited to 6,500 N using an undamped isolator, we will use the following formula to determine the maximum permissible stiffness of the isolator that serves the purpose.
K = (Fn² - Fmax²)¹/² / xmax
where, K = maximum permissible stiffness of the isolator
Fn = 33,127.02 N
Fmax = 6,500 N
xmax = 0.5 mm
K = ((33,127.02)² - (6,500^2))¹/² / 0.5K = 184,294.15 N/mm
(b) Let's determine the steady-state amplitude of the exhaust fan with the isolator that has the maximum permissible stiffness.
Maximum amplitude (X) = F / K
Maximum amplitude (X) = 33,127.02 / 184,294.15
Maximum amplitude (X) = 0.18 mm
Therefore, the steady-state amplitude of the exhaust fan with the isolator that has the maximum permissible stiffness is 0.18 mm.
Learn more about stiffness:
brainly.com/question/14687392
#SPJ11
Assuming that the required power for cruising an airplane with a total weight of 200 kgf and a cruising speed of 15 m / s is 1 kW, obtain the following values. The air density is constant at 1.25 kg / m^3 regardless of altitude.
1) Find the required power for the above airplane to fly ascending at a speed of 15 m / s at an ascending angle of 3°.
2) When the above airplane travels on a concrete runway with µ= 0.02 with constant thrust while maintaining a horizontal state from a state where it is stationary on the ground, the drag coefficient CD and lift coefficient CL of the entire aircraft are constant regardless of speed. If so, find the thrust required to reach 15 m / s in one minute from rest. Also, find the distance traveled to reach 15 m / s.
the equations related to power, force, and distance traveled. Let's calculate the required values:
1) Required power for ascending flight:
The required power for ascending flight can be calculated using the following equation:
P_ascend = (F_ascend × V) / η
where P_ascend is the required power, F_ascend is the ascending force, V is the velocity, and η is the efficiency.
Since the ascending angle is given as 3°, we can calculate the ascending force using the equation:
F_ascend = Weight × sin(θ)
where Weight is the total weight of the airplane.
Substituting the given values, we have:
Weight = 200 kgf = 200 × 9.81 N (conversion from kgf to Newtons)
θ = 3°
V = 15 m/s
η = 1 (assuming 100% efficiency)
Calculating the ascending force:
F_ascend = Weight × sin(θ)
Now, we can calculate the required power for ascending flight:
P_ascend = (F_ascend × V) / η
Learn more about distance formula here:
brainly.com/question/30853813
#SPJ11
You are an engineer working at Samsung producing Galaxy mobile phones. The products have got the following failure mode, the charger cable damaged and not charging properly, Use your knowledge, skills and engineering background to apply the process of Failure Mode Effects Analysis FMEA aiming the reduction of failure or prevent it. You must design the FMEA table and explain every single column
The FMEA table includes columns for Item/Process/Function, Failure Mode, Potential Effects of Failure, Severity, Potential Causes, Occurrence, Current Controls, Detection, RPN, Recommended Actions, Responsibility, and Target Completion Date.
The FMEA (Failure Mode Effects Analysis) table is a systematic approach used to identify potential failure modes, their effects, and their causes in a product or process. Each column in the table serves a specific purpose:
Item/Process/Function: Identifies the specific component, process, or function being analyzed.
Failure Mode: Describes the potential ways in which the item/process/function can fail.
Potential Effects of Failure: Lists the consequences or impacts resulting from the failure.
Severity: Rates the severity of each potential effect on a predefined scale.
Potential Causes: Identifies the underlying reasons or sources that could lead to the failure mode.
Occurrence: Rates the likelihood or frequency of occurrence of each potential cause.
Current Controls: Describes the existing measures or controls in place to prevent or detect the failure.
Detection: Rates the effectiveness of the current controls in detecting the failure mode.
RPN (Risk Priority Number): Calculates the RPN by multiplying Severity, Occurrence, and Detection ratings.
Recommended Actions: Suggests actions or improvements to reduce the occurrence or severity of failure modes.
Responsibility: Assigns the person or team responsible for implementing the recommended actions.
Target Completion Date: Sets the deadline for completing the recommended actions.
By systematically analyzing and addressing each column in the FMEA table, engineers can identify potential failures and take proactive measures to prevent or minimize them, thereby improving product quality and reliability.
Learn more about Failure Mode Effects Analysis here:
https://brainly.com/question/33269577
#SPJ11
Q3 Fast Fourier Transform (FFT) is a technique that can be used to estimate the frequency spectrum of any signal. Consider ↓ as a signal in 1 second. (a) (b) [1,9,0,0,1,6] Estimate its frequency spectrum using the FFT. Plot the magnitude and phase response of the calculated spectrum.
To estimate the frequency spectrum of a signal, we can use Fast Fourier Transform (FFT). The signal given in the question is as follows:[1, 9, 0, 0, 1, 6]The length of the signal is 6, and the sampling frequency is 6Hz. The following steps must be taken to estimate the frequency spectrum using FFT:
1. First, import the necessary libraries and define the signal as a NumPy array.
2. Apply FFT to the signal to obtain the complex spectrum, using numpy.fft.fft(signal). The output of this step is a complex spectrum that has a magnitude and a phase component.
3. Use numpy.fft.fftfreq(signal.size, 1/sampling_frequency) to obtain the frequency component of the spectrum. This function returns an array of frequency values that correspond to the complex spectrum.
4. Finally, plot the magnitude and phase components of the spectrum using matplotlib.
This is done using the following two commands:plt.plot(frequency_component, np.abs(complex_spectrum))
plt.plot(frequency_component, np.angle(complex_spectrum))
We can use Fast Fourier Transform (FFT) to estimate the frequency spectrum of a signal. The signal given in the question has a length of 6 and a sampling frequency of 6Hz. To estimate the frequency spectrum using FFT, we first import the necessary libraries and define the signal as a NumPy array. Next, we apply FFT to the signal to obtain the complex spectrum, which has magnitude and phase components. We then use numpy.fft.fftfreq to obtain the frequency component of the spectrum, and finally plot the magnitude and phase components of the spectrum using matplotlib. The magnitude and phase response of the calculated spectrum can be plotted using plt.plot(frequency_component, np.abs(complex_spectrum)) and plt.plot(frequency_component, np.angle(complex_spectrum)), respectively.
Therefore, by following the above steps, we can estimate the frequency spectrum of a signal using FFT. The magnitude and phase components of the calculated spectrum can be plotted using matplotlib.
To know more about NumPy visit:
https://brainly.com/question/30396727
#SPJ11
For a reversible refrigerator, Coefficient of Performance is given by OT2/(T1-T2) OT1/(T2-T1) O T1/(T1-T2) O T2/(T2-T1) "
The COP equation provides a quantitative measure of the efficiency of a reversible refrigerator in terms of the temperature differences involved in the cooling process.
The Coefficient of Performance (COP) is a measure of the efficiency of a refrigerator, representing the amount of cooling it produces per unit of work input. For a reversible refrigerator, the COP is given by the ratio of the temperature difference between the cold and hot reservoirs to the temperature difference between the hot and cold reservoirs.
the COP is calculated as COP = T2 / (T1 - T2), where T1 is the temperature of the high-temperature reservoir (source) and T2 is the temperature of the low-temperature reservoir (sink).
A higher COP indicates a more efficient refrigerator, as it produces more cooling per unit of work input. By minimizing the temperature difference between the hot and cold reservoirs, the COP can be improved. However, the COP is limited by the temperature range at which the refrigerator operates.
Learn more about efficiency here:
brainly.com/question/30853813
#SPJ11
This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. In the sport of roller derby, players must pass a Minimum Skills test, in order to be allowed to participate in bouts. In one part of the test a skater must get 27 laps around the track in 5 minutes. Auntie Matter is a skater for the Reservoir Dolls, a roller derby team in Madison, Wisconsin. She is testing today to show that she can get her 27 in 5 . Auntie studies physics, and she decides to determine in advance the minimum centripetal acceleration she will need in order to pass this tost. Also, given that she knows the coefficient of friction of her wheels is 0.73 and her mass on skates is 79 kg. she decides to find the maximum number of laps she could get before losing friction and skidding off the track. That is the maximum force of static friction on Auntie, in Joules? (Please provide an answer before moving to the next part.) he maximum force of static friction on Auntie is N.
Calculate the value of F_friction using the given values, and provide the result in Joules for the maximum force of static friction on Auntie Matter.
To determine the minimum centripetal acceleration Auntie Matter needs to pass the test, we can start by calculating the required speed.
v = N / t
Next, we need to calculate the centripetal acceleration (a) using the formula:
a = v^2 / r
To pass the test, Auntie Matter needs to maintain a centripetal acceleration that allows her to maintain a certain radius of curvature while skating. However, the specific radius of the track is not provided in the question.
Moving on to the second part of the question, to determine the maximum force of static friction before Auntie skids off the track, we can use the following equation:
Maximum force of static friction (F_friction) = coefficient of friction (μ) * Normal force (N)
Given:
Coefficient of friction (μ) = 0.73
Mass of Auntie Matter (m) = 79 kg
Acceleration due to gravity (g) = 9.8 m/s^2
The normal force (N) can be calculated as:
N = m * g
Finally, we can calculate the maximum force of static friction:
F_friction = μ * N
Substituting the values, we get:
F_friction = μ * m * g
Learn more about F_friction here:
brainly.com/question/30853813
#SPJ11
Consider an equilateral triangular plate ABC that is controlled by a hydraulic cylinder D. At the instant when 0 = 60 deg, the plate has angular velocity w = = 1 k [rad/s] and angular acceleration a = w = ¤ = 0.2 k [rad/s²]. Each side of the plate has length b = 0.2 m. Find: a) the velocity of point A at this instant. b) the acceleration of point A at this instant. Hint: cos (60 deg) = sin(30 deg) = 0.5 0.2 x sin(60deg) = 0.173 b x- B b = 0.2 m b D A
The velocity of point A at the given instant is 0.0173 k [m/s]. The acceleration of point A at the given instant is 0.04 k [m/s²].
To find the velocity of point A at this instant, we can use the formula: velocity = angular velocity * distance from the axis of rotation.
Given:
Angular velocity (w) = 1 k [rad/s]
Distance from the axis of rotation (b) = 0.2 m
The velocity of point A can be calculated as:
Velocity of A = w * b * sin(60 deg) = 1 k [rad/s] * 0.2 m * sin(60 deg) = 0.1 k [m/s] * 0.173 = 0.0173 k [m/s]
Therefore, the velocity of point A at this instant is 0.0173 k [m/s].
To find the acceleration of point A at this instant, we can use the formula: acceleration = angular acceleration * distance from the axis of rotation.
Given:
Angular acceleration (a) = 0.2 k [rad/s²]
Distance from the axis of rotation (b) = 0.2 m
The acceleration of point A can be calculated as:
Acceleration of A = a * b = 0.2 k [rad/s²] * 0.2 m = 0.04 k [m/s²]
Therefore, the acceleration of point A at this instant is 0.04 k [m/s²].
Learn more about acceleration here:
brainly.com/question/2303856
#SPJ11
Consider the following fragment of assembly code: ARRAY DW 7,6,5,4 COUNT DW 4 LABEL1: LABEL2: XOR AX, AX STC MOV CX, COUNT MOV SI, OFFSET ARRAY ADC AX, WORD PTR [SI] ADD SI, 2 LOOP LABEL1 a. (2 Pts.) What will be the value in AX when control reaches label2? b. (1 Pts.) What is the purpose of the line: XOR AX, AX c. (2 Pts.) Write an efficient and functionally equivalent code segment for the line: loop labell
The given code segment demonstrates a loop that iterates until the value of the CX register becomes zero. The XOR AX, AX statement clears the AX register, and the loop efficiently continues until CX equals zero. The value of AX at label2 will be 22H.
a. At the end of the loop, the value of AX will be 22H. Hence, the value of AX at label2 will be 22H.
b. The XOR AX, AX statement will clear the AX register, making it equivalent to 0. It’s important to clear out the register, particularly if we are to sum some values later, to make sure that the result will be accurate.
c. The loop labell statement will continue the loop until the value of the CX register is zero. Hence, an efficient and functionally equivalent code segment for the statement is given below:cmp cx,0 ; Compare the value in CX with 0jz label2 ; If CX is equal to 0, jump to label2dec cx ; Decrement the value of CXjmp label1 ; Continue with the loop, back to label1
Learn more about code segment: brainly.com/question/25781514
#SPJ11
QUESTION 10 Plot the Bode Plot for low pass filter with R=3.3kΩ and C=0.033μF. Include all the calculation stpes and points on Bode Plot. Each step carry marks.
A Bode plot is a graph that describes a linear, time-invariant system's frequency response using two axes: the magnitude of the frequency response (in decibels) and the phase (in degrees).
It is a logarithmic plot of the system's magnitude and phase as a function of frequency. It is used to predict how the system will react to specific frequencies and how its performance will be impacted by specific components.In order to plot the Bode plot for a low pass filter with
R=3.3kΩ and
C=0.033μF,
we must first calculate the cutoff frequency and then plot the gain and phase shift.
The formula for calculating the cutoff frequency (fc) is as follows:
fc = 1/(2πRC)
= 1/(2π(3.3kΩ)(0.033μF))
= 1507.96 Hz
The Bode plot is divided into two sections: the magnitude plot and the phase plot. The magnitude plot is plotted on the y-axis, and the frequency is plotted on the x-axis. The phase plot is plotted on the y-axis, and the frequency is plotted on the x-axis. Both plots are plotted on logarithmic scales. The magnitude plot is plotted in decibels (dB), and the phase plot is plotted in degrees (°).Gain: The gain plot for the low pass filter is given by the equation
A(f) = 20 log(Vout/Vin) where Vin and Vout are the input and output voltages of the filter, respectively.
The gain plot is a straight line with a slope of -20 dB/decade.
Phase Shift: The phase shift plot for the low pass filter is given by the equation
φ(f) = -arctan(2πfRC) where f is the frequency of the input signal. The phase shift plot is a straight line with a slope of -45°/decade.\
Calculation steps:-The cutoff frequency is calculated using the formula
fc = 1/(2πRC).-
The gain plot is plotted using the equation
A(f) = 20 log(Vout/Vin) where Vin and Vout are the input and output voltages of the filter, and respectively.-The phase shift plot is plotted using the equation
φ(f) = -arctan(2πfRC)
where f is the frequency of the input signal.-Both plots are plotted on logarithmic scales.-The main plot is a straight line with a slope of -20 dB/decade.-The phase shift plot is a straight line with a slope of -45°/decade.
To know more about Bode Plot visit:
https://brainly.com/question/31494988
#SPJ11
Which of the followings is true? For FM and sinusoidal messages, is the modulation index. For arbitrary messages, the modulation index corresponds to O A. B. O B. D. O C.C. O D.A. QUESTION 26 Which of the followings is true? For AM and wideband FM, the main difference between their modulation indices is that O A. AM index is less than1 but FM index is restricted. O B. FM index is less than1 but AM index is restricted. O C. AM index is less than1 but not the FM index. O D. FM index is less than 1 but not the AM index.
The correct answer is:C. AM index is less than 1, but not the FM index.In amplitude modulation the modulation index represents the ratio of the peak amplitude of the modulating signal to the peak amplitude of the carrier signal.
The modulation index for AM is typically less than 1.On the other hand, in frequency modulation (FM), the modulation index does not have a strict upper limit or restriction. It can have values greater than 1, depending on the characteristics of the modulating signal. The modulation index for FM is not restricted to be less than 1.Therefore, option C correctly states that the modulation index for AM is less than 1, but it does not specify any restriction for the modulation index in FM.
Learn more about modulation here:
https://brainly.com/question/28520208
#SPJ11
the phrase ad hoc queries means:- group of answer choices -programmed queries -new, one-of-a-kind queries -highly structured queries -standard queries
The phrase "ad hoc queries" means new, one-of-a-kind queries. Ad hoc queries are created on the spot, usually to solve an immediate need. Ad hoc is a Latin term that means "for this purpose."
Ad hoc queries refer to one-time, one-of-a-kind queries that are generated on the fly to answer a particular question or satisfy an immediate need. Ad hoc queries are typically requested by power users or business analysts, and they are frequently ad hoc because the user does not know what data is available or how the data can be accessed.
The Advantages of Ad Hoc Queries:-
Ad hoc queries can provide several advantages, including the ability to answer a one-time query or provide information that is not available in existing reports.
Ad hoc queries are frequently employed in data discovery and data mining activities because they allow users to interactively explore data and spot trends that might not be immediately obvious.
Another significant benefit of ad hoc queries is the ability to generate fresh insight and detect anomalies that standard reports might overlook.
Additionally, ad hoc queries can be used to identify data-quality issues that need to be resolved.
In summary, ad hoc queries provide flexibility and agility for users to solve issues that may arise quickly.
To learn more about "Ad hoc Queries" visit: https://brainly.com/question/30736256
#SPJ11