Answer:
Radioactivity means: the emission of ionizing radiation or particles caused by the spontaneous disintegration of atomic nuclei.
Explanation: I hope this helps! :)
Answer:
sending out harmful radiation caused when the nuclei (=central parts) of atoms are broken up.
In which image below is the angle of refraction the greatest?
Answer:
Explanation:
Angle of refraction is the angle made by refracted ray with the normal at the point of incidence . In this figure , refracted ray has been shown by line having arrow-head . Normal has been shown by broken line .
We observe that in figure D , angle made by refracted ray with normal is greatest . So figure D is the answer.
The image where the angle of refraction is the greatest is the image D
What is the angle of refraction?The angle of refraction is the angle that the refracted ray made with the x-axis.
The higher the angle between the refracted ray and the x-axis, the higher the angle of refraction and vice versa.
From the given diagram, we can see that the image where the angle of refraction is the greatest is the image D
Learn more on angle of refraction here: https://brainly.com/question/15838784
6. A total of 135 J of work is done on a gaseous refrigerant as it undergoes compression. If
the internal energy of the gas increases by 114 J during the process, what is the total amount
of energy transferred as heat? Has energy been added to or removed from the refrigerant as
heat?
Answer:
Eh = 21 [J]
Removed as heat.
Explanation:
This is a case of energy conservation, we have to take into account the energies that go in and out of the system. In this case, 135 [J] of energy are entered in the form of work of the compressor to the chamber where the refrigerant is compressed, now of these 135 [J] 114 [J] were used as internal energy, this internal energy is used to increase the pressure and temperature of the refrigerant.
In this way the rest of the energy of the 135 [J] was lost in the form of heat to determine this loss of energy, we simply perform the arithmetic subtraction.
Eh = 135 - 114 = 21 [J]
Eh = 21 [J]
What is the form of energy that our eyes can detect?
A. Sound Energy
B. Chemical Energy
C. Light Energy
D. Thermal Energy
Answer: C. Light energy.
Explanation:
if 8000cm3 of liquid drains off an hour glass in one hour, what is the flow rate of water from the clock
Answer:
8000cm³/hr
Explanation:
Given parameters:
Volume of the liquid draining off per hour = 8000cm³
Time taken to drain off = 1hr
Unknown:
Flow rate = ?
Solution:
Flow rate is the volume of fluid that passes per unit of time.
Flow rate = [tex]\frac{volume of fluid}{time taken}[/tex]
Flow rate = [tex]\frac{8000cm^{3} }{1hr}[/tex]
Flow rate = 8000cm³/hr
What effect will the following have on the inertia of a body if
(i) the force acting on it is increased.
(ii) the mass of the body is reduced.
Explanation:
Inertia is the tendency of a body to remain at rest or to do nothing.
It is the resistance to any change in position of body.
When the force on a body increases, the inertia reduces
When the mass is reduced the inertia reduces
According to newton's first law or the law of inertia "an object will remain in its state of rest or of uniform motion unless if it is acted upon by an external force".
Finding the area of a trapezoid on a velocity versus time graph will tell you
the ——————
of an object.
A. displacement
B. acceleration
C. velocity
D. distance
1.A runner has a displacement of 20 meters in 5 seconds, what is his velocity
during this time?
Answer:
The required velocity of runner is 4m/s.
A baseball bat is a lever. Which of the following explains how a baseball bat differs from a lever like a pry bar?
Complete question is;
A baseball bat is a lever. Which of the following explains how a baseball bat differs from a lever like a pry bar?
A) In a baseball bat, effort force is smaller and is applied over a large distance, while the resistance force is smaller and is applied over a long distance.
B) In a baseball bat, effort force is smaller and is applied over a large distance, while the resistance force is smaller and is applied over a short distance.
C) In a baseball bat, effort force is larger and is applied over a short distance, while the resistance force is smaller and is applied over a long distance.
D) In a baseball bat, effort force is larger and is applied over a short distance, while the resistance force is smaller and is applied over a short distance.
Answer:
C) In a baseball bat, effort force is larger and is applied over a short distance, while the resistance force is smaller and is applied over a long distance.
Explanation:
The correct answer is option C. This is because unlike in a pry bar, the effort force when swinging a baseball bat is larger and it is applied over a short distance; and in return the resisting force is smaller and it's applied over a long distance.
15 POINTS URGENT DUE IN 5 MINUTES :(
please don’t troll.
A. A woman hiked on a trail up a mountainShe slowed down as it became more steep. She stopped at the top to take in the view below. Then she continued on the trail and walked down the other side of the mountain.
B. A truck driver left a warehouse and drove on a highway at a constant speed before he stopped for lunch. To make up for lost time, he drove faster when he got back on the highway. He unloaded his haul and drove quickly back to the warehouse.
C. A woman drove her car up steep bill and stopped at a red lightWhen the light turned green she continued to drive up the rest of the hill until she reached the gas station. She stopped to buy gas and then drove down the other side of the hill towards her office.
D. A man ran in a race and accelerated steadily for the first hour. He then continued briefly at a constant pace while he had the lead. When other runners began to catch up he accelerated againHe then continued at a constant high speed. He became overtired and slowed down until he had to completely stop running.
Answer:
D now go to ur good life :)
Explanation:
Answer:
blah
Explanation:
blah
A car accelerates from 20 m/s to 80 m/s in 5 seconds. What is the
average acceleration of the car?
a 20 m/s2
b 12 m/s2
C 4 m/
d 16 m/s2
Answer:
12m/s2
Explanation:
:D (just a smiley, not answer d)
I need help asappp!!! Help b trcrcrhhvvcc
Answer:
the answer is c. hope this help you out
Students in a science class were provided with this image and asked to identify which color of light would refract the most if white light was passed through a prism?which student below identified the correct color of light with the proper justification?
The identification of the correct color of the light with the proper justification would be by student 4: violet, because it has the highest frequency, therefore the correct answer is option D.
What is Wavelength?It can be understood in terms of the distance between any two similar successive points across any wave for example wavelength can be calculated by measuring the distance between any two successive crests.
As given in the problem, students in a science class were provided with this image and asked to identify which color of light would refract the most if white light was passed through a prism.
Student 4 would correctly identify and justify violet as the appropriate hue of the light since it has the greatest frequency, making option D the right response.
To learn more about wavelength from here, refer to the link;
brainly.com/question/7143261
#SPJ2
What, exactly, is moving across the medium?
Answer:
So waves are everywhere. But what makes a wave a wave? What characteristics, properties, or behaviors are shared by the phenomena that we typically characterize as being a wave? How can waves be described in a manner that allows us to understand their basic nature and qualities?
A wave can be described as a disturbance that travels through a medium from one location to another location. Consider a slinky wave as an example of a wave. When the slinky is stretched from end to end and is held at rest, it assumes a natural position known as the equilibrium or rest position. The coils of the slinky naturally assume this position, spaced equally far apart. To introduce a wave into the slinky, the first particle is displaced or moved from its equilibrium or rest position. The particle might be moved upwards or downwards, forwards or backwards; but once moved, it is returned to its original equilibrium or rest position. The act of moving the first coil of the slinky in a given direction and then returning it to its equilibrium position creates a disturbance in the slinky. We can then observe this disturbance moving through the slinky from one end to the other. If the first coil of the slinky is given a single back-and-forth vibration, then we call the observed motion of the disturbance through the slinky a slinky pulse. A pulse is a single disturbance moving through a medium from one location to another location. However, if the first coil of the slinky is continuously and periodically vibrated in a back-and-forth manner, we would observe a repeating disturbance moving within the slinky that endures over some prolonged period of time. The repeating and periodic disturbance that moves through a medium from one location to another is referred to as a wave.
Hope That Helps!!
Explanation:
A subway car moves at a constant speed of 10 m/s over a period of 10 s. What is the instantaneous speed halfway through this motion
Answer: 10 m/s
We're told the speed is constant, so it's not changing throughout the time period given to us. So throughout the entire interval, the speed is 10 m/s.
would someone just answer this now?
Answer:
x=36.5 m
Explanation:
Rectangular Components of a Vector
A vector can be expressed as an ordered pair (x,y) where x is the x-coordinate, and y is the y-coordinate of a rectangular system.
It can also be given as a magnitude-angle pair (r,θ) where θ is measured from the positive x-axis. It's also known as polar coordinates.
The conversion from polar to rectangular coordinates is:
[tex]x=r\cos \theta[/tex]
[tex]y=r\sin\theta[/tex]
We are given the vector as a magnitude r=47.3 m and at an angle θ=39.4°. The x-component of the vector is:
[tex]x=47.3\cos (39.4^\circ)[/tex]
Using a scientific calculator to find the trigonometric function:
[tex]x=47.3\cdot 0.7716[/tex]
x=36.5 m
whats the net force
Answer:
13n pushing left
Explanation:
1563 - 1550
Diffraction occurs when waves _______ around the edge of a barrier?
Answer:
travels
Explanation:
hope this helps and have a blessed day
A pumpkin is thrown horizontally off of a building at a speed of 2.5 m/s and travels a horizontal distance of 12 m before hitting the ground.
What was the initial height of the pumpkin?
What was the final vertical velocity of the pumpkin?
Answer:
-47.04
Explanation:
Divide 12 m by 2.5 m/s which equals 4.8s
And then use 4.8s to multiply it with -9.8
4.8(-9.8)= -47.04 m/s
Hope this helped!! :)
The initial height of the pumpkin is 23.52m and the final vertical velocity of the pumpkin is 47.04 m/s.
Laws of motion:Initial horizontal speed, u = 2.5 m/s
horizontal distance covered , d = 12m
So the time taken is:
t = d/u
t = 12/2.5 s
t = 4.8s
Now, the initial vertical speed, v = 0
So the vertical distance traveled by the pumpkin will be equal to the initial height of the pumpkin:
s = vt + ¹/₂gt²
s = 0.5 × 9.8 × 4.8 m
s = 23.52m
Final vertical velocity:
v' = v + gt
v' = 9.8 × 4.8 m/s
v' = 47.04 m/s
Learn more about laws of motion:
https://brainly.com/question/26083484?referrer=searchResults
A runner is training and runs past meter mark 65 and starts a stopwatch. After the runner passes meter mark 15 the stopwatch stops at 8 seconds. What was the runners velocity?
Question 5 options:
-6.25 m/s
6.25 m/s
8.13 m/s
-1.88 m/s
Answer:
-6.25 m/s
Explanation:
i took the quiz
A student hangs the south pole of a bar magnet near the north pole of
another hanging bar magnet. What do the magnets do?
A. They move away from each other.
B. They move away from each other, then toward each other.
C. They move toward each other.
O D. They do not move.
When the south pole of a bar magnet is near the north pole of another bar magnet, they move toward each other. Therefore, option (C) is correct.
What is a magnet?A magnet can be described as a substance that creates a magnetic field and this magnetic field is the reason for the considerable properties of a magnet. The magnetic force pulls ferromagnetic materials, such as iron, cobalt, etc., and attracts or repels other magnetic substances.
A permanent magnet is composed of a material that is magnetized and produces its own magnetic field such material can be magnetized, and strongly attracted towards a magnet, is known as ferromagnetic, and contain the elements iron, and cobalt.
Each bar magnet possesses a set of North and South poles within them. The south pole of one magnet brings closer to the north pole of another magnet they attract each other and move toward each other.
Learn more about the magnet, here:
brainly.com/question/2841288
#SPJ5
A group of athletes are trying to turn a large wheel and axle to move a stone. What can they do to move the wheel with less effort?
What will happen if we increase the friction on a roller coaster?
A. The speed of the roller coaster will increase.
B. The speed of the roller coaster will decrease
C. The speed of the roller coaster will remain constant.
D. The roller coaster will fly away
Answer: B. The speed will decrease.
Explanation:
When you ride a roller coaster, the wheels rub/scrape the rails, creating heat as a result of friction. And friction will slow you down. So increasing the friction on a roller coaster would slow it down.
Answer:
B
Explanation:
Friction opposes motion therefore reducing motion
Is a ball a wheel and axle if so how do you calculate the Mechanical Advantage of the ball? If not what kind of simple machine is a ball?
which change to a circuit is most likely to increase it electrical power
A: increase it's current and increase it's voltage
B: decrease it's current and increase it's voltage
C: decrease it's current and decrease it's voltage
D: increase it's current and decrease it's voltage
Answer:
A................
Explanation:
Hope this helps you
A. increase it's current and increase it's voltage
Explanation:
Why do we use insulators if they prevent the flow of electricity?
Answer:
letterman is shooting the kids
We use insulators to avoid being electrocuted. electricians use rubber gloves to avoid shock. Cables are insolated with rubber so you can hold them without getting shocked even if it is plugged in.
with what force will the a car hit a tree if the car has a mass of 3,000 kg and a acceleration of 2m/s^2
Answer:
The answer is 6000 NExplanation:
The force acting on an object given it's mass and acceleration can be found by using the formula
force = mass × acceleration
From the question we have
force = 3000 × 2
We have the final answer as
6000 NHope this helps you
10. A golf ball is propelled with an initial velocity of 60
meters per second at 37° above the horizontal. The
horizontal component of the golf ball's initial veloc-
ity is
the horizontal component of the golf ball's initial velocity is 47.92 m/s.
The given parameters;
initial velocity of the golf, v = 60 m/s
angle of projection of the golf, Ф = 37°
The horizontal component of the golf ball's initial velocity is calculated as follows;
[tex]v_0_x = v\times cos(\theta)\\\\[/tex]
[tex]v_0_x[/tex] = 60 m/s x cos (37)
[tex]v_0_x[/tex] = 60 m/s x 0.7986
[tex]v_0_x[/tex] = 47.92 m/s
Thus, the horizontal component of the golf ball's initial velocity is 47.92 m/s.
Learn more here: https://brainly.com/question/14304606
5. Describe the trip from your home to school using the words
position, distance, displacement, and speed.
My commute to school is a constant distance, but the time it takes to get there fluctuates owing to traffic.
What is displacement?If an object moves with respect to a reference frame, such as when a passenger travels to the back of an airliner or a professor moves to the right with respect to a whiteboard, the item's position changes.
This change in location is described as displacement.
My commute to school is a constant distance, but the time it takes to get there fluctuates owing to traffic,
The initial and the final position of the commute is the same, but the displacement varies with the route which affects my car's speed and where it is in line at stop lights.
Learn more about displacement here, refer to the link;
https://brainly.com/question/10919017
#SPJ2
How do you measure the wavelength of wave?
Explanation:
by finding the distance between two successful crest
Answer:
the wavelength can be measured as the distance from crest to crest or from trough to trough , the wavelength of a wave can be measured as the distance from a point on a wave to the corresponding point on the next cycle of the wave.
Explanation:
What is the difference between physical & chemical changes?
Slate whether each is an example of a Physleat (P) or Chemteal (C) property
1. Arock's density
2. boiling point of Gatorade
3. ability of an old car to rust
4. red color of a pe apple
S ability of wood to ignite
8. bitler taste of a lemon
7. melting point of wax
8. hardness of marble
9. Luster (shininess) of gold
boiling point Gatoride