Answer:
Environmental science and protection technicians both use laboratory equipment, such as microscopes, to analyze samples collected in the field. Environmental science and protection technicians also monitor the environment and investigate sources of pollution and contamination, including those affecting public health.
Hope this was helpful ;)
answer is a and b jjjjxjxjxjxjx xxxjxjxj
Describe the role of C-S-H in providing strength for cement. Discuss which compounds produce C-S-H and why balancing the amounts of those compounds is important.
Answer:
Following are the solution to this question:
Explanation:
Whenever a chemical reaction occurs between water and cement the heat is released, and a [tex]CaOSiO_2H_2O[/tex] (C-S-H gel) gel constructs gel is also recognized as "tobermorite gel."
This one gel acts like a pack of gum and also has a cement quality, that holds its particles intact and therefore contributes to the overall compression mix. An increase in supply explicitly causes the movement in the outcome of power. C3S and C2S are both the compounds of Bouge that produce hydration C-S-H gel.
It mixture must be balanced as [tex]Ca(OH)_2[/tex] with C-S-H gel also is given as a byproduct. It [tex]Ca(OH)_2[/tex] , that cause sudden with sulphate and form [tex]CaSO_4[/tex] , is an unacceptable substance. Sulfate attack or later deterioration of its cement is caused by this [tex]CaSO_4[/tex] .
All C3S and C2S generate various amounts of C-S-H gel so, the required strength can be maintained without compromising on real term durability.
A wet electrode can cause arc blow ?
Answer:
yes it can
Explanation:
List the three main phases of photo interpretation in photogrammetry
Answer:
Stages of Interpretation and Mapping
Selection of photographs. Whenever possible, all photographs of a site or small area should be assessed for fitness of purpose. ...
Control points. A good spread of control points on a photograph is vital to establish the exact location or size of features. ...
Transformation.
Explanation:
35 points and brainiest. A, B, C, D
Which of the following identifies what carbide-tipped bits, lines on machine bolts, and lock washers all have in common?
A. All are very expensive items.
B. All are very recent inventions.
C. All are rather outdated inventions.
D. All provide an added level of strength.
Answer:c
Explanation:
simple Brayton cycle using air as the working fluid has a pressure ratio of 10. The minimum and maximum temperatures in the cycle are 295 and 1240 K. Assuming an isentropic efficiency of 83 percent for the compressor and 87 percent for the turbine, determine (a) the air temperature at the turbine exit, (b) the net work output, and (c) the thermal efficiency.
Answer:
a) 764.45K
b) 210.48 kJ/kg
c) 30.14%
Explanation:
pressure ratio = 10
minimum temperature = 295 k
maximum temperature = 1240 k
isentropic efficiency for compressor = 83%
Isentropic efficiency for turbine = 87%
a) Air temperature at turbine exit
we can achieve this by interpolating for enthalpy
h4 = 783.05 kJ/kg ( calculated in the background ) at state 4 using Table A-17 for Ideal gas properties of air
T4 ( temperature at Turbine exit ) = 760 + ( 780 - 760 ) [tex](\frac{783.05-778.18}{800.13-778.18} )[/tex] = 764.45K
b) The net work output
first we determine the actual work input to compressor
Wc = h2 - h1 ( calculated values )
= 626.57 - 295.17 = 331.4 kJ/kg
next determine the actual work done by Turbine
Wt = h3 - h4 ( calculated values )
= 1324.93 - 783.05 = 541.88 kJ/kg
finally determine the network output of the cycle
Wnet = Wt - Wc
= 541.88 - 331.4 = 210.48 kJ/kg
c) determine thermal efficiency
лth = Wnet / qin ------ ( 1 )
where ; qin = h3 - h2
equation 1 becomes
лth = Wnet / ( h3 - h2 )
= 210.48 / ( 1324.93 - 626.57 )
= 0.3014 = 30.14%
Determine the force in members FD and DB of the frame. Also, find the horizontal and vertical components of reaction the pin at C exerts on member ABC and member EDC.
Answer:
A.
Explanation:
What simple changes would you make to a basic PID controller if you expected the sensors to be very noisy and the target to change by large steps?
Answer:
tuning the value of Ki termincreasing/changing the Kp termExplanation:
The simple change that would be made to a basic PID controller to prevent it from been noisy is tuning the value of Ki term while
The simple change that would be made to a PID controller if you want to change the target by large steps is increasing/changing the Kp term associated with the PID controller