What are the differences among engineers, mathematics and scientist

Answer:

C. It likely was less accurate than computer results.

Explanation:

While Katherine Johnson's calculations were extremely precise, they were done by hand using paper and pencil, without the aid of modern computers. This means that they were more prone to human error than modern computer results, which are calculated using digital algorithms and software designed specifically for accuracy and reliability. Additionally, modern computing is much faster and can handle larger and more complex calculations than Johnson's manual methods.

The primary function of a circuit tester is to test a receptacle device.

A circuit tester is a tool used to determine if an electrical outlet (receptacle) is properly wired and functioning correctly. It is designed to detect the presence of electrical current and can determine if a receptacle is wired correctly or if there is a fault in the wiring.

To use a circuit tester, you simply plug it into the receptacle and observe the indicator lights or readouts. If the tester indicates that the receptacle is properly wired, it will typically display a series of lights or a message that confirms that the receptacle is working correctly. If there is a fault in the wiring, the tester will indicate this with a different set of lights or a message that alerts the user to the problem.

Therefore, While a circuit tester can be used to test other electrical devices, such as toggle switches, circuit breakers, and amperage, its primary function is to test electrical receptacles.

Learn more about circuit tester from

https://brainly.com/question/30064584

#SPJ1

The correct answer is To determine the dimension of a cylindrical riser for the casting of an aluminum cube of sides 15 cm, we need to consider the shrinkage that occurs during solidification.

The volume of the cylindrical riser should be equal to the volume of the aluminum cube plus the shrinkage volume. Since the shrinkage volume is given to be 6.5% of the volume of the aluminum cube, we can calculate it as follows:Shrinkage volume = [tex]6.5/100 * (15)^3[/tex][tex]= 172.6875 cm^3[/tex]To find the volume of the cylindrical riser, we can use the formula:  Volume of a cylinder = [tex]πr^2h[/tex]  Let's assume the height of the riser to be h and the radius to be r. We know that the volume of the riser should be 3% of the shrinkage volume plus the volume of the aluminum cube:

Volume of riser[tex]= 3/100 * 172.6875 + 15^3[/tex][tex]= 221.78 cm^3[/tex] Substituting this value into the formula for the volume of a cylinder, we get: [tex]πr^2h = 221.78[/tex]  Since we don't have any information about the height of the riser, we can assume it to be h. Solving for r, we get: [tex]r = sqrt(221.78/(πh))[/tex] Therefore, the dimension of the cylindrical riser would depend on the height of the riser, which is not given in the problem statement. We would need to know the height to calculate the radius of the cylindrical riser.

To learn more about cylindrical riser click on the link below:

brainly.com/question/16344141

#SPJ1

Technician B is correct. An emissions vacuum schematic is given on a decal under the hood. When dealing with vehicle repairs, it is crucial to understand the vacuum system.

The vacuum system on a car is critical for many reasons, such as powering the brakes and some emissions control systems. With all of this in mind, the car's vacuum system must be maintained and repaired to ensure that everything runs correctly. When performing repairs on the vacuum system, it is important to have an emissions vacuum schematic on hand.

A vacuum diagram is a simplified schematic representation of the vacuum system. An emissions vacuum schematic is given on a decal under the hood of a car that shows the vehicle's emission and vacuum routing. It may also show the engine's firing order, spark plug gap, and other information. On the other hand, the factory service manual may contain more detailed information about the vehicle's vacuum system.

Learn more about vacuum system at

https://brainly.com/question/7033113

#SPJ11

Prepare a strategy for handling a hazardous material occurrence. Damage to hazardous material containers should be noted. Identify any dangerous substances. Determine the size of a threatened region.

When there is an emergency involving potentially harmful substances, a Hazmat Technician responds. You determine how to properly dispose of the hazardous materials as a Hazmat Technician by identifying them. Asbestos, lead, mercury, mould, radioactive waste, and nuclear waste are a few examples of materials you might frequently deal.

In order to support business operations and provide high-quality outputs, a materials technician is in charge of examining, testing, and guaranteeing the stability and efficiency of the tools and materials needed for production operations and manufacturing processes.

To know more about hazardous material visit:-

https://brainly.com/question/29630735

#SPJ1

An input gear has 55 teeth and the output gear has 25 teeth. The gear ratio of these gears is 2.2:1.

By dividing the number of teeth on the driven gear (output gear) by the number of teeth on the driving gear, the gear ratio can be calculated (input gear). The driven gear in this instance has 25 teeth, while the driving gear has 55 teeth, resulting in the following gear ratio:

For calculating gear ratio, divide by the number of teeth on the driving gear.

25/55 is the gear ratio.

45% or a gear ratio of 0.45

In a gear reduction system, the output gear rotates more quickly than the input gear. The gear ratio determines the speed differential between the gears. In this instance, the output gear has a gear ratio of 0.45, which indicates that it rotates 1/0.45 times faster than the input gear. output gear with 25 teeth turns faster, and it is 2.2 times faster than the input gear with 55 teeth.

To learn more about Ratio :

https://brainly.com/question/28391198

#SPJ4

The gear ratio of these gears is 2.2:1 . The output gear turns faster than the input gear, and it turns 54.55% faster than the input gear.

To solve this problem, we need to know the gear ratio and which gear turns faster.

We can start by finding the gear ratio.

An input gear has 55 teeth and the output gear has 25 teeth.

What is the gear ratio of these gears?

The gear ratio is the ratio of the number of teeth on the input gear to the number of teeth on the output gear. Therefore, the gear ratio is:

Gear Ratio = Number of Teeth on Input Gear/Number of Teeth on Output Gear

Gear Ratio = 55/25

Gear Ratio = 2.2:1

This means that the input gear rotates 2.2 times for each rotation of the output gear.

Which gear turns faster and how much faster is it compared to the other gear?

The gear that turns faster is the output gear, which has fewer teeth.

To determine how much faster it turns, we can use the gear ratio.

The gear ratio tells us that the input gear turns 2.2 times for each rotation of the output gear.

Therefore, the output gear turns 2.2 times faster than the input gear.

To calculate how much faster the output gear is turning, we can use the following formula:

Speed Ratio = Output Gear Teeth/Input Gear Teeth

Speed Ratio = 25/55

Speed Ratio = 0.4545

This tells us that the output gear turns at 45.45% of the speed of the input gear, or 54.55% faster than the input gear.

For similar question on gear ratio

https://brainly.com/question/860313

#SPJ11

The displacement of end A with respect to end D is 0.0724 inches.

To find the displacement of end A with respect to end D, we need to use the formula for axial deformation:

δ = (PL)/(AE)

Where P is the applied load, L is the length of the segment, A is the cross-sectional area of the segment, and E is the modulus of elasticity.

For segment AB:

δAB = (12,000 lbs)(8 in)/(π/4)(0.75 in)²(18 x 10³ ksi)
δAB = 0.0224 in

For segment BC:

δBC = (20,000 lbs)(10 in)/(π/4)(1.1 in)²(18 x 10³ ksi)
δBC = 0.0127 in

For segment CD:

δCD = (8,000 lbs)(12 in)/(π/4)(0.60 in)²(18 x 10³ ksi)
δCD = 0.0373 in

The total displacement of end A with respect to end D is the sum of the displacements of each segment:

δ = δAB + δBC + δCD
δ = 0.0224 in + 0.0127 in + 0.0373 in
δ = 0.0724 in

Learn more about axial deformation:

https://brainly.com/question/18371467

#SPJ11

Answer:

1.1 Introduction

Workshop practice is a very vast one and it is very difficult for anyone to claim a mastery over it. It provides the basic working knowledge of the production and properties of different materials used in the industry. It also explains the use of different tools, equipments, machinery and techniques of manufacturing, which ultimately facilitate shaping of these materials into various usable forms. In general, various mechanical workshops know by long training how to use workshop tools, machine tools and equipment. Trained and competent persons should be admitted to this type of mechanical works and permitted to operate equipment.

In two dimensions, the equation for a line can be written as y = mx + h. To reflect a point about this line, we can use an affine transformation matrix. The matrix for reflection about a line is given by:
[tex]$$ \begin{bmatrix} 1-2m^2 & 2mh & 2mh^2 \\ 2mh & 1-2h^2 & -2h(1+m^2) \\ 0 & 0 & 1 \end{bmatrix} $$[/tex]

To reflect a point (x, y) about the line, we simply multiply the point by this matrix:
[tex]$$ \begin{bmatrix} 1-2m^2 & 2mh & 2mh^2 \\ 2mh & 1-2h^2 & -2h(1+m^2) \\ 0 & 0 & 1 \end{bmatrix} \begin{bmatrix} x \\ y \\ 1 \end{bmatrix} = \begin{bmatrix} (1-2m^2)x + 2mhy + 2mh^2 \\ 2mhx + (1-2h^2)y - 2h(1+m^2) \\ 1 \end{bmatrix} $$[/tex]This gives us the reflected point (x', y').

To extend this result to reflection about a plane in three dimensions, we can use a similar matrix. The equation for a plane in three dimensions is given by Ax + By + Cz + D = 0. The matrix for reflection about this plane is given by:
[tex]$$ \begin{bmatrix} 1-2A^2 & -2AB & -2AC & -2AD \\ -2AB & 1-2B^2 & -2BC & -2BD \\ -2AC & -2BC & 1-2C^2 & -2CD \\ 0 & 0 & 0 & 1 \end{bmatrix} $$[/tex]

To reflect a point (x, y, z) about the plane, we simply multiply the point by this matrix:
[tex]$$ \begin{bmatrix} 1-2A^2 & -2AB & -2AC & -2AD \\ -2AB & 1-2B^2 & -2BC & -2BD \\ -2AC & -2BC & 1-2C^2 & -2CD \\ 0 & 0 & 0 & 1 \end{bmatrix} \begin{bmatrix} x \\ y \\ z \\ 1 \end{bmatrix} = \begin{bmatrix} (1-2A^2)x - 2ABy - 2ACz - 2AD \\ -2ABx + (1-2B^2)y - 2BCz - 2BD \\ -2ACx - 2BCy + (1-2C^2)z - 2CD \\ 1 \end{bmatrix} $$[/tex]
This gives us the reflected point (x', y', z').

To learn more about Matrix ;

https://brainly.com/question/23834102

#SPJ4

The viscosity of the fluid at each temperature:

Rotational viscometer: This type of viscometer measures the viscosity of a fluid by rotating a spindle or bob inside the fluid. The resistance encountered by the spindle as it rotates is proportional to the viscosity of the fluid. The rotational viscometer is highly accurate and can be used to measure the viscosity of a wide range of fluids, including liquids, gels, and pastes. However, it can be quite expensive and may require regular maintenance.

Falling ball viscometer: This type of viscometer measures the viscosity of a fluid by timing how long it takes for a ball to fall through the fluid. The faster the ball falls, the lower the viscosity of the fluid. Falling ball viscometers are relatively inexpensive and easy to use. However, they are only suitable for measuring the viscosity of low-viscosity fluids, and they may not provide highly accurate results.

b. To calculate the viscosity of the fluid using a U-Tube viscometer, we can use the following equation:

= /(2)

Using the data provided, we can calculate the viscosity of the fluid at each temperature:

At 40°C, = 57 s, so:

= /(2) = (57)/(2)

At 60°C, = 41 s, so:

= /(2) = (41)/(2)

At 80°C, = 29 s, so:

= /(2) = (29)/(2)

At 100°C, = 16 s, so:

= /(2) = (16)/(2)

Read more about fluid mechanics here:

https://brainly.com/question/25209686

#SPJ1

Traversals given in option B would print all of the elements in the 2D array of integers nums in row-major order .So, the correct answer is option B: for(int row = 0; row < nums.length; row++) { for(int col = 0; col < nums[0].length; col++) { System.out.println(nums[row][col]); } }.

This traversal would print all of the elements in the 2D array of integers nums in row-major order because it first iterates through the rows of the array, and then through the columns within each row. This is the definition of row-major order, where the elements are accessed row by row, from left to right and top to bottom.

Option A would print the elements in column-major order, option C would not access all of the elements in the array, and option D contains syntax errors that would prevent the code from running.

You can learn more about 2D array at

https://brainly.com/question/14530506

#SPJ11

To prompt the user for a string that contains two strings separated by a comma, you can use the `input()` function in Python. The `input()` function allows you to prompt the user for input and store it in a variable. Here is an example of how you can do this:

```python
# Prompt the user for a string
input_string = input("Enter input string: ")

# Split the string into two strings separated by a comma
string_list = input_string.split(",")

# Print the two strings
print("String 1:", string_list[0])
print("String 2:", string_list[1])
```

This will prompt the user for a string, split it into two strings separated by a comma, and print the two strings. Here is an example of the output:

```
Enter input string: Jill, Allen
String 1: Jill
String 2: Allen
```

Note that the `split()` function will split the string at the comma and return a list of the two strings. You can then access the two strings using the list indices `[0]` and `[1]`.

Learn more about function Python:

https://brainly.com/question/29334036

#SPJ11

The total number of method calls to draw all of the numbers in the seven segment form would be 56 method calls.

To draw each individual number in the seven segment form, it would take a different number of method calls depending on the number being drawn.

Here is the breakdown for each number:

1: 2 method calls (initialize and moveForward)2: 6 method calls (initialize, moveForward, turnRight, moveForward, turnRight, moveForward)

3: 5 method calls (initialize, moveForward, turnRight, moveForward, turnRight)

4: 5 method calls (initialize, moveForward, turnLeft, moveForward, turnLeft)

5: 6 method calls (initialize, moveForward, turnLeft, moveForward, turnLeft, moveForward)

6: 7 method calls (initialize, moveForward, turnLeft, moveForward, turnLeft, moveForward, turnLeft)

7: 4 method calls (initialize, moveForward, turnRight, moveForward)

8: 8 method calls (initialize, moveForward, turnRight, moveForward, turnRight, moveForward, turnRight, moveForward)

9: 6 method calls (initialize, moveForward, turnRight, moveForward, turnRight, moveForward)

0: 7 method calls (initialize, moveForward, turnRight, moveForward, turnRight, moveForward, turnRight)

So, the total number of method calls to draw all of the numbers in the seven segment form would be 2 + 6 + 5 + 5 + 6 + 7 + 4 + 8 + 6 + 7 = 56 method calls.

Learn more about method calls:

https://brainly.com/question/24167967

#SPJ11

Dimensioning standards for inches and millimeters are used to specify the size and location of features on an object or part. The primary difference between these two standards is the unit of measurement used.

Inches are the primary unit of measurement in the United States, and dimensioning standards for inches are based on the imperial system of measurement. This system is based on units of inches, feet, and yards.

Dimensioning standards for inches typically use fractions of an inch, such as 1/8", 1/16", or 1/32", to specify dimensions. These fractions are commonly used because they are easy to measure with common tools like rulers and calipers.

On the other hand, millimeters are the primary unit of measurement in most other parts of the world, and dimensioning standards for millimeters are based on the metric system of measurement. This system is based on units of millimeters, centimeters, and meters.

Dimensioning standards for millimeters typically use decimals, such as 1.5 mm or 3.75 mm, to specify dimensions. Decimals are commonly used in the metric system because they allow for more precise measurements and are easier to work with in mathematical calculations.

For more such questions on measurement, click on:

https://brainly.com/question/30238003

#SPJ11

The tension forces in each cable can be determined by subtracting the tension in the other cables from the total force F.

Tension forces are a type of force that acts along the length of an object. These forces are created by the stretching of an object and are usually measured in Newtons. Tension forces can be found in a variety of different objects such as ropes, strings, wires, and cables. It can also be found in other objects such as springs and muscles. Tension forces can have a variety of effects on an object depending on the direction and magnitude of the force.

The forces acting on the body in the x-direction can be written as:

Fx = TAB - TAC - TAD = 0

Where TAB, TAC, and TAD are the tension forces in cables AB, AC, and AD respectively.

Therefore, we can solve for the tension forces in each cable:

TAB = TAC + TAD = F = 750 N

TAC = TAB - TAD = 750 N - TAD

TAD = TAB - TAC = 750 N - TAC

Therefore, the tension forces in each cable can be determined by subtracting the tension in the other cables from the total force F.

To learn more about tension forces

https://brainly.com/question/30089732

#SPJ1

A leftmost derivation is a type of derivation in which the leftmost nonterminal in each sentential form is the one that is expanded first. Here are the leftmost derivations for the four given statements:

a. A = (A+B) *C

S → A=E
→ A=(E)*E
→ A=(A+E)*E
→ A=(A+B)*E
→ A=(A+B)*C

b. A=B+C+A

S → A=E
→ A=E+E
→ A=E+E+A
→ A=B+E+A
→ A=B+C+A

c. A = A * (B+C)

S → A=E
→ A=E*(E)
→ A=A*(E)
→ A=A*(B+E)
→ A=A*(B+C)

d. A = B*C*(A + B)

S → A=E
→ A=E*E
→ A=E*E*(E)
→ A=E*E*(A+E)
→ A=E*E*(A+B)
→ A=B*E*(A+B)
→ A=B*C*(A+B)

In each of these derivations, the leftmost nonterminal is the one that is expanded first. This is indicated by the arrow pointing to the next sentential form.

Learn more about derivations:

https://brainly.com/question/23819325

#SPJ11

There are a few issues with the provided code:

Here's the corrected code:

#include <iostream>

using namespace std;

void PrintVal(int numberA, int numberB) {

   int product = 1;

   for(int i = numberA; i <= numberB; i++) {

       if(i > 0) {

           product = product * i;

       }

   }

   cout << product << endl;

}

int main() {

   int numberA, numberB;

   cin >> numberA >> numberB;

   PrintVal(numberA, numberB);

   return 0;

}

This should correctly output the product of all positive integers between numberA and numberB.

Learn more about programming:

https://brainly.com/question/26134656

#SPJ11

The search depth in a search tree corresponds to the number of levels in the tree. Each level in the tree represents a possible action by the maximizer. Therefore, a search depth of 2 means that the search tree considers sequences of up to 2 actions by the maximizer.

In other words, the search depth is the number of moves ahead that the maximizer is considering. A search depth of 2 means that the maximizer is considering its current move and one additional move ahead.

It is important to note that the search depth does not necessarily correspond to the number of moves made in the game. It simply represents the number of potential moves considered by the maximizer in the search tree.

In conclusion, the search depth in a search tree refers to the number of levels in the tree, with each level representing a possible action by the maximizer. A search depth of 2 means that the search tree considers sequences of up to 2 actions by the maximizer.

Learn more about search tree:

https://brainly.com/question/29672887

#SPJ11

To count the input length without spaces, periods, or commas, you can use the `replace()` method in Python to remove these characters from the input string before calculating its length. Here's how you can do it:

```python
# Get the input string
input_string = input()

# Remove spaces, periods, and commas from the input string
input_string = input_string.replace(" ", "")
input_string = input_string.replace(".", "")
input_string = input_string.replace(",", "")

# Calculate the length of the input string without spaces, periods, or commas
input_length = len(input_string)

# Print the result
print(input_length)
```

This will give you the number of characters in the input string excluding spaces, periods, or commas. For example, if the input is "Listen, Mr. Jones, calm down.", the output will be 21.

Learn more about programming:

https://brainly.com/question/26134656

#SPJ11

As a network engineer, the fiber Ethernet standard that you would apply in this situation is 1000BASE-LX. Therefore, the correct answer is d. "1000BASE-LX".

This standard is specifically designed for Gigabit Ethernet connections and is suitable for connecting a data center with a data closet in an office building. 1000BASE-LX uses a long-wavelength laser (1,270–1,355 nm) and can support distances of up to 5 km over single-mode fiber and 550 m over multimode fiber.

Therefore, the correct answer is: d. 1000BASE-LX

You can learn more about Ethernet standard at

https://brainly.com/question/28443277

#SPJ11

The area under the curve is approximated by trapezoids in the Trapezoidal rule, which estimates the definite integral of a function. The number of used trapezoids is indicated by the subscript in the notations T 2 and T 4.

The trapezoidal rule, also known as the trapezoid rule or trapezium rule, is a method for approximating the definite integral in mathematics, more specifically in numerical analysis.

Trapezoidal rule T 2 gives us the following: T 2 = (b - a) [f(a) + f(b)] f(a + (b - a)/2) = /2 + (b - a) /2 with a = 0 and b = 1 and T 2 = 2.

Simplifying and substituting the values results in:

2 = (1 - 0)[f(0) + f(1)]

/2 + (1 - 0)[f(0.5)]

/2\s2 = f(0) + f(1)/2 + f(0.5)/2

Trapezoidal rule T 4 gives us the following: T 4 = (b - a) [f(a) + f(b)]

f(a + (b - a)/4) + f(a + 3(b - a)/4) = /2 + (b - a)/2 f(a + (b - a)/2) = + (b - a)/4

where T 4 = 1.75, a = 0, and b = 1.

By simplifying and substituting the variables, we get with 1.75 = (1 - 0)[f(0) + f(1)].

/2 + (1 - 0)/2 [f(0.25) + f(0.75)] + (1 - 0)/4 [f(0.5)]

1.75 = f(0) + f(1)/2 + f(0.25) + f(0.75) + f(0.5)/4

We may rewrite the equations above as: 2 = f(0) + f(1)/2 + a 1.75 = f(0) + f(1)/2 + 2a + f(0.5)/4 since f(0.25) = f(0.75) = a.

By dividing the first equation by two and taking that result away from the second equation, we arrive at:

1.75 - 4 = f(0.5)/4 - a\s-2.25 = (f(0.5) - 4a)/4

In order to solve for a, we obtain: f(0.5) = 4a - 9 f(0.5) = 4a - 9.

When we use this f(0.5) value as a substitute in the first equation, we obtain:

2 = f(0) + f(1)/2 + a 2 = f(0) + f(1)/2 + a 2 = f(0) + f(1)/2 + a

We obtain the following by substituting f(0.5) = 4a - 9: 2 = f(0) + f(1)/2 + a 2 = f(0

To know more about integral visit:-

https://brainly.com/question/30267558

#SPJ1

Technician A and Technician B are both correct. Throttle body cleaner can be used to clean the internal components of the IAC motor, however, on some vehicles the pintle of the IAC motor can be damaged by the throttle body cleaner. Therefore, it is important to check the manufacturer's instructions to determine if it is safe to use throttle body cleaner on the IAC motor.

According to the given situation, Technician A says that throttle body cleaner may be used to clean the IAC (Idle Air Control) motor internal components. Technician B says that on some vehicles, IAC motor damage can occur if the pintle is cleaned with throttle body cleaner.

So, who is correct?

Technician B is correct. On some vehicles, IAC motor damage can occur if the pintle is cleaned with throttle body cleaner. Therefore, it is advised to check the manufacturer's recommended service procedures before using any cleaning product. A technician must not use cleaning solvents that are not specifically recommended by the manufacturer.To make sure that the IAC motor is not damaged during cleaning, the technician must carefully remove the IAC motor from the throttle body. The IAC motor should then be cleaned with an appropriate cleaner, such as electrical contact cleaner or IAC cleaner. Additionally, the technician should use a soft-bristled brush to clean the IAC motor pintle, being careful not to apply too much force during cleaning.

The IAC motor should then be reinstalled onto the throttle body with a new gasket or O-ring, as specified by the manufacturer.

Technician a says throttle body cleaner : https://brainly.com/question/31193380

#SPJ11

Assuming that the Student class from question 8 is already defined, here's how we can create two instances of the Student class and display their information using the __str__ method:

class StudentMain:

   def __init__(self):

       abby = Student("Abby", "Smith", 83.9)

       brady = Student("Brady", "Jones", 75.5)

       print(abby)

       print(brady)

student_main = StudentMain()

In the above program, we create an instance of the StudentMain class that contains the __init__ method. Inside the __init__ method, we create two instances of the Student class called abby and brady. We assign the grade 83.9 to abby and the grade 75.5 to brady.

Then, we use the print statement to display the information of both students by calling the __str__ method on each instance. Finally, we create an instance of the StudentMain class to run the program.

The output of the program will be:

Name: Abby Smith, Grade: 83.9

Name: Brady Jones, Grade: 75.5

Learn more about programming:

https://brainly.com/question/26134656

#SPJ11

Fire towers, also known as lookout towers, are structures built on high points in forests or other landscapes to provide a vantage point for detecting and reporting fires. Here are some of the advantages and disadvantages of using fire towers:

Advantages:

Disadvantages:

Learn more about  Fire Tower at:

https://brainly.com/question/29249780

#SPJ1

The base-10 number system, also known as the decimal system, is a numbering system that uses 10 digits: 0, 1, 2, 3, 4, 5, 6, 7, 8, and 9. Each digit in a base-10 number represents a specific value based on its position, with the rightmost digit representing the ones place, the next digit to the left representing the tens place, and so on.

The base-10 number system, also known as the decimal system, is a numerical system that uses ten digits (0-9) to represent all numbers. It is the system we use in our everyday lives, and it is based on the concept of place value, where each digit represents a power of 10.

On the other hand, the binary system is a numerical system that uses only two digits (0 and 1) to represent all numbers. It is commonly used in computing and electronics because it is easy to represent data as a series of binary digits, or bits.

Therefore, One key difference between the two systems is that the base-10 system is much more intuitive for humans because it is based on the number of fingers we have. We naturally count in groups of 10, which makes the base-10 system very easy for us to understand and use. In contrast, the binary system can be difficult for humans to work with because it is not based on anything in the physical world.

Learn more about  binary system here:

https://brainly.com/question/16612919

#SPJ1

To determine the force required to hold a gate with a width of 2 m at its location, use the following equation: F = W/2 x P, where W is the width of the gate, and P is the applied pressure.

To determine the force required to hold the gate ABC at its location for a gate width of 2 m into the paper, we need to use the following formula:
F = P × A × cosθ
Where:
F = Force required to hold the gate
P = Pressure of the fluid
A = Area of the gate
θ = Angle between the gate and the fluid
Since the gate width is 2 m into the paper, the area of the gate will be:
A = 2 × h
Where h is the height of the gate.
Substituting the values into the formula, we get:
F = P × (2 × h) × cosθ
Simplifying, we get:
F = 2 × P × h × cosθ

Therefore, the force required to hold the gate ABC at its location for a gate width of 2 m into the paper is 2 × P × h × cosθ.

Learn more about pressure:https://brainly.com/question/28012687

#SPJ11

We must demonstrate that we can implement any Boolean function using only NOR gates in order to prove that the NOR gate is functionally complete. EITHER A Equals A OR A

So, to implement the Boolean functions, we employ NOR gates. It's crucial to keep in mind that the NOR gate is the opposite of the basic OR gate. This indicates that the complement of the OR gate's output is equal to the output of the NOR gate.

NAND and NOR are two singleton sets that are equally functional. Unfortunately, because it is unable to represent NOT, the set of AND, OR is lacking.

To know more about function visit:-

https://brainly.com/question/28939774

#SPJ1

The appropriate material for a nonbearing exterior wall that minimizes solar heat gain while transmitting some light would be A. Glass block.

Glass block, also known as glass bricks, is a type of material that is commonly used in construction for nonbearing exterior walls. It is an excellent material for minimizing solar heat gain while still allowing some light to pass through. Glass block is also a good choice for nonbearing exterior walls because it is strong and durable, and can withstand the elements without deteriorating.

In contrast, face brick, modular brick, and grade MW brick are not as effective at minimizing solar heat gain or transmitting light. These types of materials are typically used for structural or decorative purposes, and are not designed to minimize solar heat gain or transmit light.

Therefore, the correct answer to this question is A. Glass block.

You can learn more about solar heat at

https://brainly.com/question/12667197

#SPJ11

The tension in the cable CD is 19.6N.

To find the tension in the cable CD, we can use the principle of moments. According to this principle, the sum of the clockwise moments about a point is equal to the sum of the anticlockwise moments about the same point.

Let us consider the moments about point A. The weight of the plate (W) acts at the midpoint G, which is 0.5m from point A. The tension in the cable (T) acts at point D, which is 1m from point A. Therefore, the sum of the moments about point A is:

T × 1m = W × 0.5m

Substituting the given values, we get:

T × 1m = 4kg × 9.8m/s² × 0.5m

T = (4kg × 9.8m/s² × 0.5m) / 1m

T = 19.6N

Learn more about the tension in the cable CD:

https://brainly.com/question/28106997

#SPJ11

Answer:

I think it's Cutting the sheathing of non-metallic sheathed cable.