Use the curved-arrow notation to draw the mechanism for the formation of polystyrene from styrene and benzoyl peroxide. Linear polystyrene has phenyl groups that are attached to alternate, not adjacent, carbons of the polymer chain. Refer to the answer to question four to explain the mechanistic basis for this fact.

The focal length of the new eyeglasses is -25.64 cm

When a person has a vision problem, the doctor writes a prescription for eyeglasses that can help to correct their vision. This prescription is usually measured in diopters (D), which is a unit of measurement for the refractive power of lenses. The refractive power of lenses is the reciprocal of their focal length in meters, and it can be calculated as P = 1/f, where P is the power of the lens in diopters and f is the focal length in meters.

In this problem, the prescription for the new eyeglasses is −3.90 D. Using the equation P = 1/f, we can solve for the focal length:

-3.90 D = 1/f

f = -1/3.90 m^-1

f = -25.64 cm

Therefore, the focal length of the new eyeglasses is -25.64 cm. This negative value indicates that the lenses are diverging lenses, which are used to correct nearsightedness.

Learn more about focal length at: https://brainly.com/question/14055649

#SPJ11

Using the gravitational force equation, we have:

$F = G \frac{m_1 m_2}{r^2}$

where G is the gravitational constant, $m_1$ and $m_2$ are the masses of the two balls, and r is the distance between their centers.

Plugging in the given values, we get:

$F = (6.67 \times 10^{-11} N \cdot m^2 / kg^2) \cdot \frac{(10 kg)(0.15 kg)}{(0.11 m)^2} = 8.2 \times 10^{-6} N$

So each ball exerts a gravitational force of 8.2 × 10⁻⁶ N on the other.

To find the ratio of this gravitational force to the weight of the 150 g ball:

Weight of 150 g ball = (0.15 kg)(9.8 m/s²) = 1.5 N

Ratio = (8.2 × 10⁻⁶ N) / (1.5 N) ≈ 5.5 × 10⁻⁶

Therefore, the ratio of the gravitational force to the weight of the 150 g ball is approximately 5.5 × 10⁻⁶.

Learn more about gravitational here:

https://brainly.com/question/3009841

#SPJ11

Answer:Based on current knowledge and observations, the following objects are found mostly within the thin disk of the Milky Way:

- Population 1 stars

- Open star clusters

- Gaseous nebulae

Population 1 stars are relatively young and metal-rich stars, and they are found mostly in the thin disk of the Milky Way. Open star clusters are also predominantly found in the disk and consist of young, hot stars. Gaseous nebulae are clouds of gas and dust that are associated with star-forming regions and are mostly located in the disk of the Milky Way.

Population 2 stars, on the other hand, are typically older and metal-poor, and they are found in the halo and bulge of the Milky Way. Globular star clusters are also typically found in the halo and consist of old, metal-poor stars.

learn more about Milky Way

https://brainly.com/question/30714548?referrer=searchResults

#SPJ11

Magnitude and direction of the instantaneous velocity  at t = 0, t = 1.0 s, and t = 2.0s

To find the magnitude and direction of the instantaneous velocity at t = 0, t = 1.0 s, and t = 2.0s, you would first need to provide the function that describes the motion of the object. The function could be in the form of position (displacement) as a function of time or velocity as a function of time. Once the function is given, we can find the instantaneous velocity at the specified times and determine their magnitudes and directions.

Learn more about instantaneous velocity at https://brainly.com/question/30782692

#SPJ11

The induced emf in the coil is -54.2 V

The induced emf in a coil of wire is given by Faraday's law of electromagnetic induction, which states that the magnitude of the induced emf is equal to the rate of change of magnetic flux through the coil. Mathematically, it is expressed as:

emf = -dΦ/dt

where emf is the induced emf in volts (V), Φ is the magnetic flux through the coil in webers (Wb), and t is time in seconds (s). The negative sign indicates the direction of the induced current opposes the change in the magnetic flux.

In this problem, the coil is initially in a magnetic field of 0 T and then the field increases to 0.150 T in 12.0 ms. The diameter of the coil is given as 2.10 cm, which means the radius is r = 1.05 cm = 0.0105 m. The coil has 1300 turns, so the total area enclosed by the coil is:

A = πr²n = π(0.0105 m)²(1300) = 0.00433 m²

The magnetic flux through the coil is given by:

Φ = BA

where B is the magnetic field and A is the area of the coil. At time t = 0, B = 0 T, so Φ = 0 Wb. At time t = 12.0 ms = 0.012 s, B = 0.150 T, so:

Φ = (0.150 T)(0.00433 m²) = 0.00065 Wb

The rate of change of magnetic flux is:

dΦ/dt = (0.00065 Wb - 0 Wb) / (0.012 s - 0 s) = 54.2 T/s

Therefore, the induced emf in the coil is:

emf = -dΦ/dt = -(54.2 T/s) = -54.2 V

Note that the negative sign indicates the direction of the induced current is such that it opposes the increase in the magnetic field.

learn more about emf here

brainly.com/question/29656124

#SPJ4

The frequency of the fundamental is 71 Hz. An overtone is a frequency that is a multiple of the fundamental frequency. The first overtone is twice the frequency of the fundamental, the second overtone is three times the frequency of the fundamental, and so on.

In this case, we are given the frequencies of two successive overtones of a vibrating string: 482 Hz and 553 Hz.
We can use this information to find the frequency of the fundamental by working backwards. If the second overtone is 553 Hz, then the frequency of the first overtone (which is twice the frequency of the fundamental) is 553/2 = 276.5 Hz.

Similarly, if the first overtone is 482 Hz, then the frequency of the fundamental is 482/2 = 241 Hz.
Therefore, the frequency of the fundamental of the vibrating string is 241 Hz.

To know more about frequency visit :-

https://brainly.com/question/31938473

#SPJ11

When solving problems related to L-R-C series circuits, it is important to keep in mind the properties of each component and how they interact with each other. It is also important to understand the different damping regimes and how they affect the behavior of the circuit.

An L-R-C series circuit is a circuit that consists of an inductor, a capacitor, and a resistor, all connected in series. In this circuit, the values of the inductor, L, and the capacitor, C, are given, and the value of the resistor, R, needs to be determined. This can be done by using the formula for the resonant frequency of the circuit, which is given by f = 1/(2π√(LC)). By measuring the resonant frequency of the circuit and using this formula, the value of R can be calculated.

It is important to note that this circuit can be either overdamped, critically damped, or underdamped, depending on the value of R. In an underdamped circuit, the value of R is such that the circuit oscillates with a frequency that is slightly different from the resonant frequency. This can be observed as a decaying sinusoidal waveform.

You can learn more about circuits at: brainly.com/question/12608491

#SPJ11

The orthogonality relation you want to verify is ∫(p₀(x)ψ₂(x)) dx = 0, where p₀(x) and ψ₂(x) are harmonic oscillator eigenfunctions for n=0 and n=2.

To verify this, first note the eigenfunctions for a harmonic oscillator:
p₀(x) = (1/√π) * exp(-x²/2)
ψ₂(x) = (1/√(8π)) * (2x² - 1) * exp(-x²/2)

Now, evaluate the integral:
∫(p₀(x)ψ₂(x)) dx = ∫[(1/√π)(1/√(8π)) * (2x² - 1) * exp(-x²)] dx

Integrate from -∞ to ∞, and the product of the eigenfunctions will cancel out each other due to their symmetric nature about the origin, resulting in:
∫(p₀(x)ψ₂(x)) dx = 0

This confirms the orthogonality relation for the harmonic oscillator eigenfunctions p₀(x) and ψ₂(x) for n=0 and n=2.

To know more about harmonic oscillator click on below link:

https://brainly.com/question/30354005#

#SPJ11

To calculate the velocity of the moving air using the given information, we can use Bernoulli's equation, which relates the pressure and velocity of a fluid. In this case, we can assume that the air is moving through a pipe and that the pressure difference measured by the manometer is due to the air's velocity.

Bernoulli's equation states that:
P1 + 1/2ρv1^2 = P2 + 1/2ρv2^2
where P1 and P2 are the pressures at two different points in the pipe, ρ is the density of the fluid, and v1 and v2 are the velocities at those points.
In this case, we can assume that the pressure at the bottom of the manometer (point 1) is equal to atmospheric pressure, since the air is open to the atmosphere there. The pressure at the top of the manometer (point 2) is therefore the sum of the atmospheric pressure and the pressure due to the velocity of the air.
Using this information, we can rearrange Bernoulli's equation to solve for the velocity of the air:
v2 = sqrt(2*(P1-P2)/ρ)
where sqrt means square root.
Plugging in the given values, we get:
v2 = sqrt(2*(101325 Pa - 13.6*10^3 kg/m^3 * 9.81 m/s^2 * 0.205 m)/(1.29 kg/m^3))
v2 ≈ 40.6 m/s
Therefore, the velocity of the moving air is approximately 40.6 m/s.

To know more about velocity visit:

https://brainly.com/question/17127206

#SPJ11

The work done by the force F(x) = (-2.0x)N as the particle moves from x = 4m to x = 5.0m, is -9N×m.

we need to integrate the force over the distance traveled by the particle.

The work done by a force F(x) over a distance dx is given by dW = F(x) dx. So the total work done by the force as the particle moves from x = 4m to x = 5.0m is:

W = ∫ F(x) dx, from x=4m to x=5.0m

= ∫ (-2.0x) dx, from x=4m to x=5.0m

= [-x²] from x=4m to x=5.0m

= -5.0² + 4²

= -9N×m

So the force F(x) = (-2.0x)N does -9N×m of work on the particle as it moves from x = 4m to x = 5.0m.

To learn more about force  visit: https://brainly.com/question/12785175

#SPJ11

Since the magnetic field is into the page (as indicated by the dots), and the current is from A to B, the force on section BC will be perpendicular to and out of the page, which is option B.

To determine the direction of the force acting on section BC of the coil, we need to use the right-hand rule for magnetic fields.

With the fingers of your right hand pointing in the direction of the current (from A to B), curl your fingers towards the direction of the magnetic field (from north to south) and your thumb will point in the direction of the force on section BC.

The dimensions of the coil (length and width) are not relevant in determining the direction of the force in this scenario.

To know more about field of coil https://brainly.com/question/13091447

#SPJ11

i.) A water molecule has a dispersion equal to 1.

ii.) The smallest silicon particle consisting of a silicon atom and its nearest neighbors has a dispersion of 4/5.

i.) In a water molecule (H₂O), there are 3 atoms in total, which are 2 hydrogen atoms and 1 oxygen atom. All of these atoms are on the surface of the molecule. Therefore, the dispersion of a water molecule is:

Number of surface atoms / Total number of atoms = 3/3 = 1

ii.) For the smallest silicon particle consisting of a silicon atom and its nearest neighbors, let's assume it forms a tetrahedron with one silicon atom at the center and four silicon atoms as its nearest neighbors. In this case, there are 5 atoms in total, and only the 4 atoms on the vertices are on the surface. The dispersion of this silicon particle is:

Number of surface atoms / Total number of atoms = 4/5

So, the dispersion for the water molecule is 1, and for the smallest silicon particle, it is 4/5.

Learn more about dispersion here: https://brainly.com/question/14263432

#SPJ11

The potential energy of the reservoir is 9.81 x 10¹³ joules. It can be generated by the dam by converting the potential energy of the water into kinetic energy and then into electrical energy using turbines and generators.

The reservoir's potential energy (PE) can be computed as the product of the volume of water and the weight of water per unit volume (density), as well as the gravitational acceleration and the reservoir's height (head):

PE = V * ρ * g * h

where:

V = reservoir volume = 10 km3 = 10 x 109 m3 = density of water = 1000 kg/m3 g = acceleration due to gravity = 9.81 m/s2 h = reservoir average head = 100 m

Substituting the values yields:

10 x 109 m3 * 1000 kg/m3 * 9.81 m/s2 * 100 m

= 9.81 x 1013 Joules.

For such more question on potential:

https://brainly.com/question/26978411

#SPJ11

To compute the potential energy (PE) of the reservoir created by the hydroelectric dam, we need to use the formula.

PE = mgh
where m is the mass of the water in the reservoir, g is the acceleration due to gravity, and h is the height of the water above a reference point.
First, we need to calculate the mass of water in the reservoir. To do this, we can use the formula:
m = density x volume
where density of water is approximately 1000 kg/m3.
Therefore, m = 1000 kg/m3 x 10 km3 x 1,000,000,000 m3/km3
m = 1.0 x 1016 kg
Next, we need to calculate the height of the water above a reference point. Since the average head of the reservoir is given as 100 m, we can use that as the height.
Now we can substitute the values into the formula for PE:
PE = mgh
PE = 1.0 x 1016 kg x 9.81 m/s2 x 100 m
PE = 9.81 x 1018 J
Therefore, the potential energy of the reservoir created by the hydroelectric dam is approximately 9.81 x 1018 Joules.

To compute the potential energy (PE) of the reservoir created by a hydroelectric dam with a volume of 10 km³ and an average head of 100 m, follow these steps:
1. Convert the volume of the reservoir to cubic meters: 10 km³ = 10 * (1000 m)³ = 10,000,000,000 m³.
2. Determine the mass of water in the reservoir using the formula: mass = volume * density. The density of water is approximately 1000 kg/m³. Therefore, the mass of water in the reservoir is 10,000,000,000 m³ * 1000 kg/m³ = 10,000,000,000,000 kg.
3. Calculate the potential energy using the formula: PE = mass * gravitational constant (g) * height. The gravitational constant (g) is approximately 9.81 m/s². So, the potential energy of the reservoir is 10,000,000,000,000 kg * 9.81 m/s² * 100 m = 9,810,000,000,000,000 J (joules).

Visit here to learn more about hydroelectric dam:

brainly.com/question/22969870

#SPJ11

The Reynolds number for a 1-foot diameter sphere moving at 2.3 miles per hour through seawater is approximately 218,835. This value represents the relative importance of inertial and viscous forces in the fluid flow around the sphere.

To calculate the Reynolds number, we can use the following formula: Re = (ρvL)/μ, where Re is the Reynolds number, ρ is the fluid density, v is the velocity of the object, L is the characteristic linear dimension (diameter in this case), and μ is the dynamic viscosity of the fluid.

First, we need to convert the given velocity from miles per hour to meters per second. 2.3 miles per hour is approximately 1.028 meters per second.

Next, we can find the density of seawater by multiplying its specific gravity by the density of water. The density of water is approximately 1,000 kg/m³, so the density of seawater is: 1,000 kg/m³ x 1.027 = 1,027 kg/m³.

Now we can substitute the values into the Reynolds number formula:

Re = (ρvL)/μ
Re = (1,027 kg/m³ x 1.028 m/s x 0.3048 m) / (1.07 x 10⁻³ Ns/m²)
Re ≈ 218,835

The Reynolds number for the given scenario is approximately 218,835.

To know more about Reynold's number, click here;

https://brainly.com/question/31748021

#SPJ11

The required current for the superconducting solenoid is approximately 9.0E+2 A.

To calculate the required current for the superconducting solenoid, we can use the formula for the magnetic field strength (B) produced by a solenoid:
B = μ₀ * n * I
where B is the magnetic field strength (3.50 T), μ₀ is the permeability of free space (417 x 10^-7 T-m/A), n is the number of turns per meter (984 turns/m), and I is the current in amperes (A).
Rearranging the formula to solve for I:
I = B / (μ₀ * n)
Plugging in the given values:
I = 3.50 T / ((417 x 10^-7 T-m/A) * (984 turns/m))
I ≈ 9.0E+2 A
So, the required current for the superconducting solenoid is approximately 9.0E+2 A.

For more such questions on solenoid , Visit:

https://brainly.com/question/25562052

#SPJ11

To determine the required current for the superconducting solenoid, we need to use the formula for the magnetic field generated by a solenoid: B = u * n * I, where B is the magnetic field, u is the permeability of free space (given as Mo in this case), n is the number of turns per unit length (984 turns/m), and I is the current.

Rearranging the formula, we get : I = B / (u * n)

Plugging in the given values, we get : I = 3.50 T / (417x10^-7 T-m/A * 984 turns/m) = 2.8E+3 A

Therefore, the required current for the superconducting solenoid to generate a magnetic field of 3.50 T with 984 turns/m is 2.8E+3 A.

Learn more about current here : brainly.com/question/13076734

#SPJ11

Rotational motion is defined as the movement of an object around an axis or a point. Rotational velocity, on the other hand, refers to the speed at which the object is rotating around its axis. It is measured in radians per second (rad/s) or degrees per second (°/s). Rotational velocity depends on two factors: how far the object rotates and how fast it rotates.

The first factor, how far the object rotates, refers to the angle that the object rotates through. This is measured in radians or degrees and is related to the distance traveled along the circumference of a circle. The second factor, how fast the object rotates, refers to the rate of change of the angle over time. It is measured in radians per second or degrees per second and is related to the angular speed of the object.
Therefore, the definition of rotational velocity is the rate of change of the angle of rotation of an object over time. It describes how quickly the object is rotating around its axis and is related to the angular speed of the object. It does not depend on the force needed to achieve the rotation, as this is related to the torque applied to the object.

learn more about velocity

https://brainly.com/question/12392559

#SPJ11

The volume of the iron cube will increase by approximately 0.313 cm³ when heated from 8.4°C to 68.1°C.To solve this problem, we need to use the formula for volume expansion due to temperature change:
ΔV = V₀αΔT

Where ΔV is the change in volume, V₀ is the initial volume, α is the coefficient of linear expansion, and ΔT is the change in temperature.
First, let's calculate the initial volume of the iron cube:
V₀ = a³
V₀ = 5.6³
V₀ = 175.616 cm³
Next, let's calculate the change in temperature:
ΔT = T₂ - T₁
ΔT = 68.1 - 8.4
ΔT = 59.7 c°
Now we can calculate the change in volume:
ΔV = V₀αΔT
ΔV = 175.616 * 10^-5 * 59.7
ΔV = 0.1049 cm³
Therefore, the volume of the iron cube will increase by 0.1049 cm³ if it is heated from 8.4°c to 68.1°c.

The coefficient of linear expansion of iron is 10–5 per c°. The volume of an iron cube, 5.6 cm on edge. How much will the volume increase if it is heated from 8.4°c to 68.1°c? To solve this problem, we need to use the formula for volume expansion due to temperature change. First, we calculate the initial volume of the iron cube which is V₀ = a³ = 5.6³ = 175.616 cm³. Next, we calculate the change in temperature which is ΔT = T₂ - T₁ = 68.1 - 8.4 = 59.7 c°. Using the formula ΔV = V₀αΔT, we can calculate the change in volume which is ΔV = 175.616 * 10^-5 * 59.7 = 0.1049 cm³. Therefore, the volume of the iron cube will increase by 0.1049 cm³ if it is heated from 8.4°c to 68.1°c.

To know more about volume visit :-

https://brainly.com/question/14996332

#SPJ11

The symbol for an atom with ten electrons, ten protons, and twelve neutrons is 22Ne. This is because the atom has 10 protons, which identifies it as a neon element (Ne).

The atomic mass is the sum of protons and neutrons (10+12), which equals 22. Therefore, the symbol is 22Ne.

The symbol for an atom with ten electrons, ten protons, and twelve neutrons is 22Ne.The other two symbols you provided, 32Mg and 32Ne, correspond to atoms with 12 protons and 20 neutrons (magnesium-32) and 10 protons and 22 neutrons (neon-32), respectively.

To know more about electrons visit :-

https://brainly.com/question/12001116

#SPJ11

The total number of bright spots (indicating complete constructive interference) is 2,The angle of the bright spot farthest from the center is approximately 0.06 degrees

Part A:

The total number of bright spots can be found using the equation:

nλ = d(sinθ + sinθ')

where n is the order of the bright spot, λ is the wavelength of light, d is the distance between adjacent slits on the grating,

θ is the angle between the incident ray and the normal to the grating, and θ' is the angle between the diffracted ray and the normal to the grating.

For maximum constructive interference, sinθ = 1 and sinθ' = 1, which gives:

nλ = d(2)

n = 2d/λ

The largest value of n occurs when sinθ is maximized, which is when θ = 90 degrees. Therefore, the maximum value of n is:

nmax = 2d/λmax

Substituting the given values, we get:

nmax = 2(1/299 mm)/631 nm

nmax ≈ 2

Part B:

The angle of the bright spot farthest from the center can be found using the equation:

dsinθ = mλ

where d is the distance between adjacent slits on the grating, θ is the angle between the incident ray and the normal to the grating, m is the order of the bright spot, and λ is the wavelength of light.

For the bright spot farthest from the center, m = 1. The maximum value of sinθ occurs when θ = 90 degrees. Therefore, we have:

dsinθmax = λ

Substituting the given values, we get:

sinθmax ≈ λ/(d*m) ≈ 0.00105

Taking the inverse sine of this value, we get:

θmax ≈ 0.06 degrees

To know more about interference refer here :-

https://brainly.com/question/31857527#

#SPJ11

An LTI (linear time-invariant) continuous-time system is a type of system that has the property of being linear and time-invariant.

This means that the system's response to a given input is independent of when the input is applied, and the output of the system to a linear combination of inputs is the same as the linear combination of the outputs to each input.

To find the zero input response of an LTI continuous-time system with initial conditions, we need to consider the system's response when the input is zero. In this case, the system's output is entirely due to the initial conditions.

The zero input response of an LTI continuous-time system can be obtained by solving the system's differential equation with zero input and using the initial conditions to determine the constants of integration. The differential equation that describes the behavior of the system is typically a linear differential equation of the form:

y'(t) + a1 y(t) + a2 y''(t) + ... + an y^n(t) = 0

where y(t) is the output of the system, y'(t) is the derivative of y(t) with respect to time, and a1, a2, ..., an are constants.

To solve the differential equation with zero input, we assume that the input to the system is zero, which means that the right-hand side of the differential equation is zero. Then we can solve the differential equation using standard techniques, such as Laplace transforms or solving the characteristic equation.

Once we have obtained the general solution to the differential equation, we can use the initial conditions to determine the constants of integration. The initial conditions typically specify the value of the output of the system and its derivatives at a particular time. Using these values, we can determine the constants of integration and obtain the particular solution to the differential equation.

In summary, to find the zero input response of an LTI continuous-time system with initial conditions, we need to solve the system's differential equation with zero input and use the initial conditions to determine the constants of integration. This allows us to obtain the particular solution to the differential equation, which gives us the zero input response of the system.

To learn more about linear time-invariant refer here:

https://brainly.com/question/31041284

#SPJ11

In Jack London's "To Build a Fire," the dog's final movement towards civilization is significant because it suggests that the dog recognizes the dangers of the natural world and has a desire to seek safety and security in human civilization.

This movement highlights the dog's intelligence and adaptation to its environment. It also suggests that the dog's relationship to nature is one of survival and instinct.

The dog is not driven by a conscious decision to seek civilization, but rather by a primal instinct to survive. This reinforces the theme of the harsh and unforgiving nature of the Yukon wilderness, where only the strongest and most adaptable can survive.

Overall, the dog's movement towards civilization symbolizes the tension between nature and civilization, and the struggle for survival in a hostile environment.

To learn more about movement, refer below:

https://brainly.com/question/2856566

#SPJ11

1. The absolute magnitude of the reduction in variation of Y when time is introduced into the regression model can be calculated by subtracting the variance of Y in the original model from the variance of Y in the new model.

2. The relative reduction can be calculated by dividing the absolute magnitude by the variance of Y in the original model.

3. The latter measure is called the coefficient of determination or R-squared and represents the proportion of variance in Y that can be explained by the regression model.

When time is introduced into a regression model, it can have an impact on the variation of the dependent variable Y. The absolute magnitude of this reduction in variation can be measured by calculating the difference between the variance of Y in the original model and the variance of Y in the new model that includes time. The relative reduction in variation can be calculated by dividing the absolute magnitude of the reduction by the variance of Y in the original model.
The latter measure, which is the ratio of the reduction in variation to the variance of Y in the original model, is called the coefficient of determination or R-squared. This measure represents the proportion of the variance in Y that can be explained by the regression model, including the independent variable time. A higher R-squared value indicates that the regression model is more effective at explaining the variation in Y.

To know more about magnitude visit:

brainly.com/question/2596740

#SPJ11

The volume at 35°C is approximately 69.86 liters

The solution to the problem: "A mass of gasoline occupies 70.01 at 20°C.  the volume at 35°C" is given below:Given,M1= 70.01; T1 = 20°C; T2 = 35°CVolume is given by the formula, V = \frac{m}{ρ}

Volume is directly proportional to mass when density is constant. When the mass of the substance is constant, the volume is proportional to the density. As a result, the formula for calculating density is ρ= \frac{m}{V}.Using the formula of density, let's find out the volume of the gasoline.ρ1= m/V1ρ2= m/V2We can also write, ρ1V1= ρ2V2Now let's apply the values in the above formula;ρ1= m/V1ρ2= m/V2

ρ1V1= \frac{ρ2V2M1}{ V1}  = ρ1 (1+ α (T2 - T1)) V1V2 = V1 / (1+ α (T2 - T1)) Given, M1 = 70.01; T1 = 20°C; T2 = 35°C

Therefore, V2 = \frac{V1 }{(1+ α (T2 - T1))V2}=\frac{ 70.01}{(1 + 0.00095 * 15) } [α for gasoline is 0.00095 per degree Celsius]V2 = 69.86 liters (approx)

Hence, the volume at 35°C is approximately 69.86 liters.

learn more about density Refer: https://brainly.com/question/32242821

#SPJ11

The wavelength of the wave is approximately 0.376 meters.

Wavelength can be defined as the distance between two successive crests or troughs of a wave. It is measured in the direction of the wave.

The speed of a sound wave is related to its wavelength and time period by the formula, λ = v × T where, v  is the speed of the wave, λ is the wavelength of the wave and T is the time period of the wave.

To find the wavelength of a wave with a speed of 75.0 m/s and a period of 5.03 ms, you can use the formula:

Wavelength = Speed × Period

First, convert the period from milliseconds to seconds:
5.03 ms = 0.00503 s

Now, plug in the given values into the formula:
Wavelength = (75.0 m/s) × (0.00503 s)

Multiply the values:
Wavelength ≈ 0.376 m

So, the wavelength of the wave is approximately 0.376 meters.

Learn more about "wavelength": https://brainly.com/question/10750459

#SPJ11

The equation for an ellipse centered at the origin with semi-major axis a and semi-minor axis b is:

[tex]x^2/a^2 + y^2/b^2 = 1[/tex]

In this problem, the ellipse has dimensions of 80 feet by 60 feet. Since the center is not specified, we can assume that the center is at the origin. Thus, the equation of the ellipse is:

[tex]x^2/40^2 + y^2/30^2 = 1[/tex]

We want to find the width 32 feet from the center, which means we need to find the height of the ellipse at x = 32. To do this, we can rearrange the equation of the ellipse to solve for y:

[tex]y = ±(1 - x^2/40^2)^(1/2) * 30[/tex]

Since we are only interested in the positive value of y, we can simplify this to:

[tex]y = (1 - x^2/40^2)^(1/2) * 30[/tex]

Substituting x = 32, we get:

y = (1 - 32^2/40^2)^(1/2) * 30

y = (1 - 256/1600)^(1/2) * 30

y = (1344/1600)^(1/2) * 30

y = 0.866 * 30

y = 25.98

Therefore, the width 32 feet from the center is approximately 25.98 feet.

To know more about refer ellipse centered here

brainly.com/question/27603973#

#SPJ11

The fencing cost for a semicircular statuary garden with a diameter of 30 feet is approximately $471.60.

This is calculated by finding the circumference of the semicircle (half of a circle) using the formula C = πd, where d is the diameter, and then multiplying it by the cost per linear foot. The diameter of the semicircular statuary garden is 30 feet. Since we are dealing with a semicircle, we can divide the diameter by 2 to get the radius, which is 15 feet. The circumference of a circle is calculated using the formula C = πd, where π is a constant approximately equal to 3.14 and d is the diameter. Therefore, the circumference of the semicircle is C = 3.14 * 30 = 94.2 feet. The fencing cost per linear foot is $8.00. Multiplying the circumference by the cost per foot gives us $8.00 * 94.2 = $753.60. However, since we are dealing with a semicircle, we need to divide this by 2 to get the cost for the entire fence around the garden. Thus, the total fencing cost is approximately $471.60.

learn more about cost+ here:

https://brainly.com/question/31041508

#SPJ11

The maximum thermal efficiency for a heat engine operating between a source and a sink at 577°C and 27°C is most nearly equal to 64.7%.

The maximum thermal efficiency for a heat engine operating between a source and a sink at 577°C and 27°C, respectively, is given by the Carnot efficiency formula, which is 1 – (Tc/Th), where Tc is the temperature of the cold reservoir and Th is the temperature of the hot reservoir. Plugging in the given values, we get

1 – (300/850) = 0.647,

which means the maximum thermal efficiency is approximately 64.7%.

This theoretical efficiency can only be approached in practice due to various factors like friction, heat losses, and imperfect thermodynamic cycles. However, it provides a useful benchmark for comparing the performance of real-world heat engines and improving their efficiency.

More on thermal efficiency: https://brainly.com/question/14615056

#SPJ11

The screen should be placed 1886.8 mm (or about 1.9 meters) away from the slits in order for the distance between the m = 0 and m = 1 bright fringes to be 1.0 cm.

To solve this problem, we can use the formula for the distance between bright fringes:
y = (mλD) / d
Where y is the distance from the central bright fringe to the mth bright fringe on the screen, λ is the wavelength of the light, D is the distance from the slits to the screen, d is the distance between the two slits, and m is the order of the bright fringe.
We want to find the distance D, given that the distance between the m = 0 and m = 1 bright fringes is 1.0 cm. We know that for m = 0, y = 0, so we can use the formula for m = 1:
1 cm = (1 x 530 nm x D) / 1 mm
Solving for D, we get:
D = (1 cm x 1 mm) / (1 x 530 nm)
D = 1886.8 mm
Therefore, the screen should be placed 1886.8 mm (or about 1.9 meters) away from the slits in order for the distance between the m = 0 and m = 1 bright fringes to be 1.0 cm.

To know more about wavelength visit:

https://brainly.com/question/31143857

#SPJ11

this circuit provides a simple and effective way to convert an input voltage signal into two output voltages, depending on whether the input voltage exceeds a threshold value.

To design a circuit that outputs 8V when the input signal exceeds 2V and -5V otherwise, we can use a comparator circuit. A comparator is an electronic circuit that compares two voltages and produces an output based on which one is larger.

In this case, we want the comparator to compare the input signal with a reference voltage of 2V. When the input voltage is greater than 2V, the output of the comparator will be high (logic 1), which we can then amplify to 8V using an amplifier circuit.

When the input voltage is less than or equal to 2V, the comparator output will be low (logic 0), and we can amplify this to -5V using another amplifier circuit.

The circuit diagram for this design is as follows:

```

     +Vcc

       |

       R1

       |

       +

   +---|----> Output

   |   |

   |  ___

   | |   |

   +-|___|-

   |   |

   R2  R3

   |   |

   -   +

    \ /

    ---

     |

     |

     Vin

```

In this circuit, R1 is a voltage divider that sets the reference voltage to 2V.

When the input voltage Vin is greater than 2V, the voltage at the non-inverting input of the comparator (marked with a `+` symbol) is greater than the reference voltage, and the comparator output goes high. This high signal is then amplified to 8V using an amplifier circuit.

When the input voltage is less than or equal to 2V, the comparator output goes low. This low signal is then amplified to -5V using another amplifier circuit.

To know more about circuit refer here

https://brainly.com/question/27206933#

#SPJ11

To design a circuit that outputs 8V when the input signal exceeds 2V and -5V otherwise, you can use a comparator along with some additional components. Here's a simple circuit design to achieve the desired functionality:

1. Start by selecting a comparator IC, such as LM741 or LM339, which are commonly available and suitable for this application.

2. Connect the non-inverting terminal (+) of the comparator to a reference voltage of 2V. You can generate this reference voltage using a voltage divider circuit with appropriate resistor values.

3. Connect the inverting terminal (-) of the comparator to the input signal.

4. Connect the output of the comparator to a voltage divider circuit that can produce two output voltage levels: 8V and -5V.

5. Connect the output of the voltage divider circuit to the output terminal of your desired circuit.

6. Make sure to include appropriate decoupling capacitors for stability and noise reduction.

Note: The specific resistor values and voltage divider circuit configuration will depend on the available voltage supply and the desired output impedance. You may need to calculate the resistor values accordingly.

Please keep in mind that when working with electronics and circuit design, it is important to have a good understanding of electrical principles, safety precautions, and proper component selection. If you are not familiar with these aspects, it is advisable to consult an experienced person or an electrical engineer to ensure the circuit is designed and implemented correctly.

To know more about comparator refer here

https://brainly.com/question/31877486#

#SPJ11

The new wavelength at which the spectral distribution has its maximum value is inversely proportional to the original temperature T1. As the original temperature was in the infrared region of the spectrum, the new wavelength would also be in the infrared region.

To start with, we know that the maximum of the spectral distribution of radiated power is at a specific wavelength in the infrared region of the spectrum. Let's call this wavelength λ1.
Now, if the total power radiated by the cavity doubles, it means that the power emitted at all wavelengths has increased by a factor of 2. This is known as the Stefan-Boltzmann law, which states that the total power radiated by a blackbody is proportional to the fourth power of its temperature (P ∝ T⁴).
Using this law, we can write:
P1/T1⁴ = P2/T2⁴
where P1 is the original power, T1 is the original temperature, P2 is the new power (which is 2P1), and T2 is the new temperature that we need to find.
Simplifying this equation, we get:
T2 = (2)⁴T1
T2 = 16T1
So the new temperature is 16 times the original temperature.
Now, to find the wavelength at which the new spectral distribution has its maximum value, we need to use Wien's displacement law. This law states that the wavelength at which a blackbody emits the most radiation is inversely proportional to its temperature.
Mathematically, we can write:
λ2T2 = b
where λ2 is the new wavelength we need to find, T2 is the new temperature we just calculated, and b is a constant known as Wien's displacement constant (which is approximately equal to 2.898 x 10⁻³ mK).
Substituting the values we know, we get:
λ2 x 16T1 = 2.898 x 10⁻³
Solving for λ2, we get:
λ2 = (2.898 x 10⁻³)/(16T1)
λ2 = 1.811 x 10⁻⁵ / T1
So the new wavelength at which the spectral distribution has its maximum value is inversely proportional to the original temperature T1. As the original temperature was in the infrared region of the spectrum, the new wavelength would also be in the infrared region.

To know more about wavelength visit ;

https://brainly.com/question/29243920

#SPJ11