Transmission lines that join two Balancing Authority Areas are known as

Answers

Answer 1
Tie Line A circuit connecting two Balancing Authority Areas. Tie Line Bias A mode of Automatic Generation Control that allows the Balancing Authority to 1.)

Related Questions

An eyewash station needs to be located no more than 10 seconds or less than 55 feet away from a work area.

Answers

However, some of the requirements include that eyewash stations be located no more than 10 seconds (or about 55 feet) from hazardous work areas. The station should be located on the same level as the hazard, have a clear path for travel, be installed in a well-lit area, and be marked with a visible safety sign

Answer: True is correct

A third-degree burn may look charred and black or dry and white.

Explanation:

In an intrinsic semiconductor, the number of free electrons is equal to what?​

Answers

Answer:

The number of holes.

Explanation:

A semiconductor can be defined as a crystalline solid substance that has its conductivity lying between that of a metal and an insulator, due to the effects of temperature or an addition of an impurity. Semiconductors are classified into two main categories;

1. Extrinsic semiconductor.

2. Intrinsic semiconductor.

An intrinsic semiconductor is a crystalline solid substance that is in its purest form and having no impurities added to it. Examples of intrinsic semiconductor are Germanium and Silicon.

In an intrinsic semiconductor, the number of free electrons is equal to  the number of holes. Also, in an intrinsic semiconductor the number of holes and free electrons is directly proportional to the temperature; as the temperature increases, the number of holes and free electrons increases and vice-versa.

In an intrinsic semiconductor, each free electrons (valence electrons) produces a covalent bond.

i need solution for this question please
Select the right answer ​

Answers

Explanation:

the 7th one answer is beacause mercury is bad at sharing electrons

the 8th one's answer is Rhodium

Answer:

1.E aluminum

2.E all

3. Either d or e leaning to e

A standard carbon resistor has a gold band to indicate + 5% tolerance. If its resistance is 3,500 , what are the upper and lower limits for its resistance? OA . 3495 - 3505 2 OB. 3300 Q - 3600 0 OC. 3325 N - 3675 OD 3450 - 35500​

Answers

Answer:

  C.  3325 Ω - 3675 Ω

Explanation:

5% of 3500 Ω is ...

  0.05 × 3500 = 175

The lower limit is this amount less than the nominal value:

  3500 -175 = 3325

The upper limit is the nominal value plus the tolerance:

  3500 +175 = 3675

The lower and upper limits are 3325 Ω and 3675 Ω, respectively.

Most hazardous waste can be disposed of in a landfill. A) TrueB) False

Answers

Answer:

This one is false

Explanation:

I just took a test on it..

Most hazardous waste can be disposed of in a landfill. Thus, the above statement is true. Thus, option (A) is correct.

What is the meaning of hazardous waste?

A hazardous waste is a waste that has characteristics that make it unsafe or allow it to negatively impact the environment or human health.

Wastes classified as hazardous have characteristics that make them unsafe or potentially damaging to the environment or human health. Liquid, solid, confined gas, and sludge are all examples of hazardous wastes.

Any source that could potentially cause injury, damage, or unfavorable health impacts to someone or something is a hazard.

The majority of hazardous garbage can be dumped in landfills. So, the aforementioned claim is accurate. Therefore, it can be concluded that option (A) is correct.

Learn more about hazardous waste here:

https://brainly.com/question/17210736

#SPJ2

What is the transfer of energy from one object to another?

Answers

Answer:

Kinetic Energy

Explanation:

Energy is transferred from one object to another when a reaction occurs. Energy can be transferred from one object to another as heat, light, and motion.

A company that produces footballs uses a proprietary mixture of ideal gases to inflate their footballs. If the temperature of 230 grams [g] of gas mixture in a 15-liter [L] tank is maintained at 465 degrees Rankine [°R] and the tank is pressurized to 135 pound-force per square inch [psi], what is the molecular weight of the gas mixture in units of grams per mole

Answers

Answer:

The molecular weight of the gas mixture is 35.38 g/mol.

Explanation:

The molecular weight of the gas can be found using the following equation:

[tex] M = \frac{m}{n} [/tex]

Where:

m: is the mass = 230 g

n: is the number of moles

First, we need to find the number of moles using Ideal Gas Law:

[tex] PV = nRT [/tex]

Where:

P: is the pressure = 135 psi

V: is the volume = 15 L

R: is the gas constant = 0.082 L*atm/(K*mol)

T: is the temperature = 465 °R (K = R*5/9)

[tex]n = \frac{PV}{RT} = \frac{135 psi*\frac{1 atm}{14.6959 psi}*15 L}{0.082 L*atm/(K*mol)*465*(5/9) K} = 6.50 moles[/tex]                

Finally, the molecular weight of the gas is:

[tex] M = \frac{m}{n} = \frac{230 g}{6.50 moles} = 35.38 g/mol [/tex]

Therefore, the molecular weight of the gas mixture is 35.38 g/mol.

I hope it helps you!

A boiler is designed to work at 14bar and evaporate 8 kg/s of water. The inlet water to the boiler has a temperature of 400C and at exit the steam is 0.95 dry. The flow velocity at inlet is 10 m/s and at exit 5 m/s and the exit is % m above the elevation at entrance. Determine the quantity of heat required. What is the significance of changes in kinetic and potential energy on the result.

Answers

Answer:

Explanation: 2 is thy answer

The easiest way to reduce your exposure to dangerous fumes is to keep your head out of a fume plume, making sure that you're breathing the cleanest air possible.

Answers

Answer:

keep your head out of a fume plume

Explanation:

According to the guidelines and precaution procedures of OSHA, an acronym for Occupational Safety and Health Administration in the United States of America stated that The easiest way for an individual to reduce his or her exposure to dangerous fumes is to ensure that such person keeps his or her head out of a fume plume.

Hence, in this situation, the correct answer is "keep your head out of a fume plume"

Which one is NOT a benefit of Shine? 1. Less production downtime 2.Happier employees 3. Improved quality 4. Inventory reduction 5. Customer satisfaction

Answers

Answer:

Inventory reduction

Explanation:

Shine is a term that deals with the general cleaning and overall maintenance of the workplace. It is used as a part of an organizational theme involving five steps which are often referred to as 5S and it is basically defined as the mainstay of the visual workplace. They are Sort, Set in order, Shine, Standardize, and Sustain.

Hence, in this situation, considering the option that is not a benefit of Shine the correct answer is "Inventory reduction." This is because Shine is not about reducing the inventory levels. It is Sort and Set-in-Order will help reduce inventory.

The answer choice which is NOT a benefit of Shine is:

D. Inventory reduction

According to the given question, we are asked to show the answer choice which is not a direct benefit of Shine and how Shine is used to increase productivity in an office space.

Shine is a term which is used to refer to the general cleanliness of an office space and is a part of organization which is used to improve quality, make the employees happier, and have a less production downtime, etc

As a result of this, we can see that inventory reduction is not a benefit of Shine.

Therefore, the correct answer is option D

Read more here:

https://brainly.com/question/22061432

Key length is designed to provide desired factor of safety
a. True
b. False

Answers

Answer: true

Explanation:

A key is a machine element that us used to connect the element of a rotating machine to a shaft. It should be noted that the key hinders the relative rotation that may take place between the two parts.

Key length is designed to provide desired factor of safety. It should also be noted that the factor of safety shouldn't be much and the key length is typically limited to the hub length.

Which of the following was an effect of world war 2 on agricultural industry

Answers

Answer:

Option C..Farmers saught new technology to help with the workload

hope this helped you

please mark as the brainliest (ㆁωㆁ)

You are an engineer working in a auto crash test lab. Some members of your team have raised objections against the use of cadavers in the crashes. No reliable data exists that shows that cadavers produces more accurate data, but many coworkers argue that common suggest they do. Others claim that the use of cadavers as mere instruments for our well-being disrespects those individuals, who have not consented to use their bodies for this purpose. The question of whether to continue to use cadavers in the lab is what kind of issue?

Answers

Answer: Application.

Explanation:

The question on wether to contine the use of cadavers in the lab for test is being centered around its application. Cadaver which is same as a corpse or dead body is used in crash site during automobil test in lab, some of this cadavers are been disrespected with their applications in the automobile industries because many didn’t consent to be used in those experiments or test.

What allows negative feedback to control a system

Answers

Answer:

Negative feedback control of the amplifier is achieved by applying a small part of the output voltage signal at Vout back to the inverting ( – ) input terminal via the feedback resistor

Answer:

The system has parts that sense the amount of output

Explanation:

Apex cirtified

Five kg of water is contained in a piston–cylinder assembly, initially at 5 bar and 240°C. The water is slowly heated at constant pressure to a final state. The heat transfer for the process is 2660 kJ and kinetic and potential energy effects are negligible. Determine the final volume, in m3, and the work for the process, in kJ.

Answers

Answer:

Explanation: that’s the answer! 46kg

A mechanical system comprises three subsystems in series with reliabilities of 98, 96, and 94 percent. What is the overall reliability of the system?

Answers

Answer:

The overall reliability of the system is 88%

Explanation:

When solving for the reliability of a complex machine, that is a machine that has more than one component, the reliability of the machine is the products of all individual components.

Given the

reliabilities of 98%,

96%, and

94%

Converting to decimals we have

98/100= 0.98

96/100= 0.96

94/100= 0.94

The product of all reliability is

0.98* 0.96 0.94= 0.88

now converting back to percent we have

0.88*100= 88%

Is microwave man made

Answers

Yes a microwave is man made

Answer:

yes..?

Explanation:

I mean humans made it? the wave length that microwaves use is not man made, but using that wave length, microwaves were made by man

4. Which of these is NOT a power wrench?
OA. Impact
OB. Air ratchet
OC. Breaker bar
OD. Air hammer

Answers

Answer:

it's C

Explanation:

hopefully that helps you

The Breaker bar is not a power wrench, the power wrench are impact, air ratchet, and air hammer option (C) is correct.

What is a power wrench?

To swiftly tighten or loosen nuts, use a power or impact wrench. They are essentially tiny, portable electric or pneumatic motors with high-speed socket wrench rotation.

As we know,

An impact wrench also referred to as an impactor, impact gun, air wrench, air gun, rattle gun, torque gun, or windy gun, is a type of socket wrench power tool that uses a rotating mass to store energy before abruptly releasing it into the output shaft to produce high torque output with little user effort.

Thus, the Breaker bar is not a power wrench, the power wrench are impact, air ratchet, and air hammer option (C) is correct.

Learn more about the power wrench here:

https://brainly.com/question/10186385

#SPJ2

what type of diagrams can you create using a compass, a T-square, a triangle, and a protractor?

Answers

Answer:

15

Explanation:

A compass may be used to create circles, arcs, bisect lines, angle bisectors, and locate midpoints. By using a compass, a protector is also drawn.

What is the compass?

A compass, or more correctly, a pair of compasses, is a tool for technical drawing that may be used to draw arcs or circles. It can also be used as dividers to indicate distances, particularly on maps.

A compass, or more correctly, a pair of compasses, is a tool for technical drawing that may be used to draw arcs or circles. It may also be used as dividers to indicate distances, particularly on maps. Compasses can be used for navigation, mathematics, and other things.

Therefore, a protector is sketched using a compass.

Learn more about the compass, refer to:

https://brainly.com/question/28136911

#SPJ2

You have a piece of film paper that is 3 in x 5 in. You fix it inside the back of a pinhole camera with a focal length of 5.5 in. You want to use it to take a picture of your team’s mascot – a giant guinea pig that just barely fits in a 4 ft. tall cube. The picture will be taken directly in front, from a stool that places the aperture 2 ft. above the ground. You have to determine how far away the camera must be from your mascot to get a good portrait that fills up the whole film paper, without cutting any part of him off. How far apart should the camera and the mascot be to take the portrait? Show your work.

Answers

Answer:

In order to take a portrait, the distance of the mascot from the camera should be approximately 7.33 feet

Explanation:

The size of the film paper = 3 in. × 5 in.

The focal length of the camera = 5.5 in.

The height and width of the guinea pig = 4 ft.

The height of the aperture above the ground = 2 ft.

Therefore, we have;

Magnification = Height of image/(Height of object)

Withe the 3 in. wide film, we have;

Magnification = 3 in./(4 ft.) = 3 in./(48 in.) = 0.0625

Magnification = Length of camera/(Distance of object from pin hole)  

∴ Length of camera/(Distance of object from pin hole) = 0.0625

Length of camera = Focal length of the camera = 5.5 in.

Therefore;

5.5 in./(Distance of object from pin hole) = 0.0625

Distance of object from pin hole = 5.5/0.0625 = 88 inches = 7.33 ft

Therefore, the camera should be approximately 7.33 ft. from the mascot to take a portrait.

In this exercise we have to use the magnification knowledge to calculate the distance that the photograph should be taken, thus we have to:

Distance of the mascot from the camera should be approximately 7.33 feet

To calculate the best distance to take the photo, we have that some information must be taken into account such as:

Size of the film paper: [tex](3)*(5) in[/tex] Focal length of the camera: [tex]5.5 in[/tex] Height and width of the guinea pig: [tex]4 ft[/tex] Height of the aperture above the ground: [tex]2 ft[/tex]

Therefore, we have that the formula of magnification is:

[tex]Magnification = Height \ of \ image/(Height \ of \ object)[/tex]

With the 3 in wide film, we have;

[tex]Magnification = 3 in/(4 ft) \\= 3 in/(48 in) = 0.0625 in[/tex]

Rewriting the magnification formula as:

[tex]Magnification = Length \ of \ camera/(Distance \ of \ object \ from \ pin \ hole)[/tex]  

Substituting the values ​​already known we have the equation will be matched as:

[tex]Length\ of \ camera/(Distance\ of\ object \ from \ pin \ hole) = 0.0625\\Length \ of \ camera = Focal \ length \ of \ the \ camera = 5.5 in.[/tex]

Therefore;

[tex]5.5 /(Distance \ of \ object\ from \ pin\ hole) = 0.0625 in\\Distance \ of \ object\ from \ pin \ hole = 5.5/0.0625\\ = 88 inches = 7.33 ft[/tex]

See more about distance at brainly.com/question/989117

A 5000-ft long X-65 pipeline is laid down on seabed with two PLETS (One at each end). The pipe OD=7-in with 0.5-in wall thickness. The pipeline was laid at environmental temperature of 40 °F (As- laid temperature). When pipeline is put into operation, the oil flow was produced at 140 °F. If the thermal expansion coefficient of the pipe material is 6.5*10-/°F and its modulus of elasticity is 30,000 ksi, determine the compressive load applied by the pipeline on a PLET due to its thermal expansion. Assume no temperature change and no seabed friction along the pipeline span.

Answers

Answer: 199.1 kip

Explanation:

Given that

Outer diameter is Do = 7 in

Inner diameter Di = ( Do - ( 2×0.5)) = 6 in

Length = 5000 ft = 60000 in

Now change in length of the pipe due to temperature difference

SL = L∝ΔT

= 60000 × 6.5×10^-6(140-40)

SL = 39 in

Also

sL = PL/AE

A = cross sectional area of pipe = π/4(Do^2 - Di^2)

so

P = SL×A×E / L

= (39 × π/4(7^2 - 6^2)×30000) / 60000

= 199.1 kip

compressive load applied by the pipeline on a PLET due to its thermal expansion is 199.1 kip

. Fume is the product of consumables, base metals, and coatings on metals during arc welding processes (during all cutting, brazing, and welding). A) TrueB) False

Answers

Answer:

True

Explanation:

This is true. Welding fumes are a combination of metallic oxides, silicates and also fluorides. the formation of these films are a result of a metal being exposed to heat above its boiling point and a condensation of its vapours into good fine particles. such films are made up of particles from the material that one is welding and also particles from electrode.

Six forces act on a beam that forms part of a building's

frame. The vector sum of the forces is zero. The magnitudes

|FB| = Fel 20 kN, Fc = 16 kN, and (Fpl = 9 kN.

Determine the magnitudes of FA and FG.

Answers

Answer:

FA = 13 kN FG = 15.3 kN

Explanation:

write each force in terms of magnitude and directions  

Fx = F sin Ф

Fy = F cos Ф

where Ф is to be measured from x axis.

∑F at y = o

FAy + FBy + FCy + FDy + FEy + FGy = 0

∑F at x = o

FAx + FBx + FCx + FDx + FEx + FGx = 0

Let  

FA = FA sin (110)   +   FA cos (110)

FB = 20 sin (270)  +  20 cos (270)

FC = 16 sin (140)    +  16 cos (140)

FD = 9 sin (40)       +  9 cos (40)

FE = 20 sin (270)    +  20 cos (270)

FG = FG sin (50)     +  FG cos (50)

add x and y forces:

FAx + FBx + FCx + FDx + FEx + FGx = 0

FAy + FBy + FCy + FDy + FEy + FGy = 0

FA sin (110)  + 0  + 16 sin (140)  + 9 sin (40)  + 0   + FG sin (50) = 0

FA cos (110) - 20 + 16 cos (140) + 9 cos (40) - 20 + FG cos (50 = 0

FA sin (110)  + 0  + 10.285  + 5.785  + 0   + FG sin (50) = 0

FA cos (110) - 20 - 12.257 + 6.894 - 20 + FG cos (50) = 0

FA sin (110)  + 16.070 + FG sin (50) = 0        

FA cos (110) - 45.363 + FG cos (50) = 0

solving for FA, and FG

FA = 13 kN

FG = 15.3 kN

From the given information, we can say that the sum of the upward forces is equivalent to the sum of the downward forces.

From the diagram, equating the component of the upward forces and the downward forces, we have:

[tex]\mathbf{-F_a sin 70 +F_c sin 40+F_d sin 40 + F_g sin50= F_b+F_e}[/tex] --- (1)

Also, the sum of the horizontal positive x-axis as well as the horizontal negative x-axis can be computed as:

[tex]\mathbf{F_g cos 50 +F_d cos 40 = F_c cos 40 +F_a cos 70 --- (2)}[/tex]

If:

[tex]F_B = F_E = 20 \ kN \\ \\ F_c = 16 \ kN \\ \\ F_D= 9\ kN[/tex]

Then, from equation (1), we can have the following:

[tex]\mathbf{F_a sin 70 + 16 sin 40 + 9 sin40 + F_gsin 50 = (20 + 20 )kN}[/tex]

collecting like terms;

[tex]\mathbf{F_a sin 70 + F_gsin 50 = 40 - 16 sin 40 - 9 sin40 }[/tex]

[tex]\mathbf{F_a sin 70 + F_gsin 50 =23.93}[/tex] --- (3)

From equation (2);

[tex]\mathbf{F_g cos 50 + 9cos 40 = 16 cos 40 + F_a cos 70}[/tex]

collecting like terms:

[tex]\mathbf{F_g cos 50 -F_a cos 70 =16cos 40 -9cos 40}[/tex]

[tex]\mathbf{-F_a cos 70 +F_g cos 50 =5.36 ----- (let \ this \ be \ equation (4))}[/tex]

Suppose we equate (3) and (4) together using the elimination method;

[tex]\mathbf{F_a sin 70 + F_gsin 50 =23.93}[/tex] --- (3)

[tex]\mathbf{-F_a cos 70 +F_g cos 50 =5.36 --- (4)}[/tex]

Let's multiply (3) with ( cos 70 ) and (4) with (sin 70);

Then, we have:

[tex]\mathbf{F_a sin 70 cos 70 + F_gsin 50 cos 70 =23.93 cos 70}[/tex]

[tex]\mathbf{-F_a cos 70 sin 70 +F_g cos 50 sin 70 =5.36 sin 70}[/tex]

Adding both previous equations together, we have:

[tex]\mathbf{F_a sin 70 cos 70 + F_gsin 50 cos 70 =23.93 cos 70}[/tex]

[tex]\mathbf{-F_a cos 70 sin 70 +F_g cos 50 sin 70 =5.36 sin 70}[/tex]

                                                                                                           

[tex]\mathbf{(0 + F_g(sin 50 cos 70 + sin70 cos50) = 23.93 cos 70 + 5.36 sin 70)}[/tex]

                                                                                                           

[tex]\mathbf{( F_g(0.262 + 0.604)) =(8.19 + 5.04)}[/tex]

[tex]\mathbf{( F_g(0.866)) =(13.23)}[/tex]

[tex]\mathbf{ F_g =\dfrac{(13.23)}{(0.866)}}[/tex]

[tex]\mathbf{ F_g =15.28 \ N}[/tex]

Replacing the value of [tex]\mathbf{F_g}[/tex] into equation (3), to solve for [tex]\mathbf{F_a}[/tex], we have:

[tex]\mathbf{F_a sin 70 + F_gsin 50 =23.93}[/tex]

[tex]\mathbf{F_a sin 70 + 15.28sin 50 =23.93} \\ \\ \mathbf{F_a sin 70 +11.71 =23.93} \\ \\ \mathbf{F_a sin 70 =23.93-11.71 } \\ \\ \mathbf{F_a sin 70 =12.22 } \\ \\ \mathbf{F_a =\dfrac{12.22 }{sin 70}} \\ \\[/tex]

[tex]\mathbf{F_a =13.01 \ N}[/tex]

Therefore, we can conclude that the magnitudes of [tex]\mathbf{F_a}[/tex] and [tex]\mathbf{F_g}[/tex] are 13.0 N and 15.28 N respectively.

Learn more about vectors here:

https://brainly.com/question/13322477?referrer=searchResults

Block B has a mass of 27g and a density of 0.9 g/mL. What is the volume of block B? Will it float in water? (density of water is 1.0 g/mL) Don't forget the units.

Answers

d = m/v
m = 27g
d = 0.9 g/mL

v = m/d
v = 27/0.9
v = 30 mL

volume is 30 mL

Steam enters a two-stage adiabatic turbine at 8 MPa and 5008C. It expands in the first stage to a state of 2 MPa and 3508C. Steam is then reheated at constant pressure to a temperature of 5008C before it is routed to the second stage, where it exits at 30 kPa and a quality of 97 percent. The work output of the turbine is 5 MW. Assuming the surroundings to be at 258C, determine the reversible power output and the rate of exergy destruction within this turbine.

Answers

Answer:

1) The exergy of destruction is approximately 456.93 kW

2) The reversible power output is approximately 5456.93 kW

Explanation:

1) The given parameters are;

P₁ = 8 MPa

T₁ = 500°C

From which we have;

s₁ = 6.727 kJ/(kg·K)

h₁ = 3399 kJ/kg

P₂ = 2 MPa

T₂ = 350°C

From which we have;

s₂ = 6.958 kJ/(kg·K)

h₂ = 3138 kJ/kg

P₃ = 2 MPa

T₃ = 500°C

From which we have;

s₃ = 7.434 kJ/(kg·K)

h₃ = 3468 kJ/kg

P₄ = 30 KPa

T₄ = 69.09 C (saturation temperature)

From which we have;

h₄ = [tex]h_{f4}[/tex] + x₄×[tex]h_{fg}[/tex] = 289.229 + 0.97*2335.32 = 2554.49 kJ/kg

s₄ =  [tex]s_{f4}[/tex] + x₄×[tex]s_{fg}[/tex] = 0.94394 + 0.97*6.8235 ≈ 7.563 kJ/(kg·K)

The exergy of destruction, [tex]\dot X_{dest}[/tex], is given as follows;

[tex]\dot X_{dest}[/tex] = T₀ × [tex]\dot S_{gen}[/tex] = T₀ × [tex]\dot m[/tex] × (s₄ + s₂ - s₁ - s₃)

[tex]\dot X_{dest}[/tex] = T₀ × [tex]\dot W[/tex]×(s₄ + s₂ - s₁ - s₃)/(h₁ + h₃ - h₂ - h₄)

∴ [tex]\dot X_{dest}[/tex] = 298.15 × 5000 × (7.563 + 6.958 - 6.727 - 7.434)/(3399 + 3468 - 3138  - 2554.49) ≈ 456.93 kW

The exergy of destruction ≈ 456.93 kW

2) The reversible power output, [tex]\dot W_{rev}[/tex] = [tex]\dot W_{}[/tex] + [tex]\dot X_{dest}[/tex] ≈ 5000 + 456.93 kW = 5456.93 kW

The reversible power output ≈ 5456.93 kW.

An input voltage of 9.2 V is to be converted into its digital counterpart using an analog-to digital converter. The voltage range is 0 to 16 V. The ADC has 4-bit capacity. Determine: (a) What are the number of quantization levels, resolution, and the maximum quantization error of this ADC

Answers

Answer:

ask someone u fool hhhhhhhh

This ball is technology too! It can be
rolled, kicked, or thrown. Is that a need
or a want?

Answers

That is an example of a want because you don't need the ball.

Want..................

What is the capacity of the machine in batches?

Answers

28 batches per day and the setup time is five minutes

Milton has been tracking the migrating patterns of whales in the northwest Atlantic Ocean for five years. He knows where and when to find them as well as how quickly they move. Which qualification makes Milton successful in his research?

Answers

Answer:

knowledge of animal behavior and anatomy

Explanation:

the qualification that will make Milton successful in his research is a knowledge of animal behaviour and also their anatomy. the knowledge of whales behaviour has opened his eyes into their world so he knows to a great deal about them. it is through his knowledge of the behaviour of whales that he's able to get used to their migrating patterns to know where and when to find them. Also, through the body anatomy of whales he knows what their movement is like.

Answer:

knowledge of animal behavior and anatomy

An analog baseband audio signal with a bandwidth of 4kHz is transmitted through a transmission channel with additive white noise. The channel is assumed to be distortionless, and the power spectral density of white noise, No/2 is 10 WHz. An RC low-pass filter with a 3-dB bandwidth of 8 kHz is used at the receiver to limit the output noise power. Calculate the output noise power.

Answers

Answer:

2k20

Explanation:

4k ✈

Other Questions
how are adding and subtracting two rational numbers with different signs related to adding and subtracting two integers with different signs. find the value of a2+y when x=4 and y=3 Explain any obstacles Sophocles faced, such as character flaws, conflicts with other people or with society, prejudice, mental or physical illness, etc. (live) How long have youhere?(marry) Thaw Zin just got to Nwe Nwe.(want) What do you reallyme to do?(go) If she feels very sick, she to the doctorat once.(cheer) The crowed(anger) His decisionas he entered the stadium.some classmates already. Write about the Altamira cave art. What are some of the interesting details? If you push a book 1.5 m across a table using a constant force of 10.0 N, how much work do youdo on the book? When should a person consider drinking a sports drink during exercise? what number gives a result of -5 when 8 is subtracted from the quotent of the number and 6 how many members does each state get in the senate help me with this qustion Whats the value of k? What was the difference in British colonization and that of France and Spain Read the sentence.We saw shiny, new tire rims on his car.Choose the correct part of speech for the underlined wordadjectiveadverbnounverb SHOW YOUR WORK!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!An experiment was conducted to find the mass of one mole of carbon atoms. The results of the experiment showed that a mole of carbon atoms had a mass of 15.78 g. The accepted value of a mole of carbon atoms is 16.00 grams. What is the percent error in this experiment? Which recurring theme topic applies to this passage?A)alienationB)good vs. evilC)the hero's journeyD)the American Dream A standard working day is 8 hours. If you were to work 125% of a normal day, how many total hours would you work? 1.54x10-1 L / 2.36x 10-45 solve this in scientific notation A is a 3 times 3 matrix with three pivot positions. (a) Does the equation Ax = 0 have a nontrivial solution? (b) Does the equation Ax = b have at least one solution for every possible b? (a) Does the equation Ax = 0 have a nontrivial solution? No Yes (b) Does the equation Ax = b have at least one solution for every possible b? No Yes What type of sentence is we went out to eat because we had no electricity .) x) x) X