To design a water delivery system to satisfy the given requirement to deliver water to a bungalow at a hill top, the following equipment is needed: Type of tank: The required type of tank is a storage tank. The tank is used to store water which will then be pumped to the bungalow.
The size of the tank will be determined by the number of people that the water will serve. For instance, if the water supply should be limited to 50 persons during peak consumption, then the tank should be able to hold enough water for 50 persons. The tank should be placed at a higher elevation to allow for easy water flow to the pump .Type of pump The type of pump required is a centrifugal pump.
A centrifugal pump is used to lift water from the tank to the bungalow. The type of pump required should be able to lift water from the storage tank to the bungalow at a height of 150 meters high. Type of pipe The type of pipe required is a PVC pipe. PVC pipes are most commonly used in water systems due to their flexibility, durability, and cost-effectiveness. The diameter of the pipe should be determined by the amount of water to be delivered and the distance from the pump to the bungalow.
Type of filter The type of filter required is a sand filter. A sand filter is used to remove any sediment or debris that may be present in the water. This is important as it ensures that the water is clean and safe for consumption .Other equipments Pipes and valves are other equipment needed for the project. Pipes and valves are important in regulating the flow of water from the storage tank to the bungalow. Valves can be used to shut off the water supply when necessary or control the flow of water to the bungalow.
To learn more about water delivery system:
https://brainly.com/question/1211617
#SPJ11
To design a water delivery system for supplying water to a bungalow house at the top of a hill, the following equipment can be considered:
1. Type of tank:
- Storage Tank: A storage tank is required to store and supply water to the bungalow house. The tank should have a capacity that can meet the water demand of 50 persons during peak consumption. It should be made of a durable and non-corrosive material.
2. Type of pump:
- Centrifugal Pump: A centrifugal pump is commonly used for water supply systems. It is efficient, reliable, and suitable for pumping water to a higher elevation. The pump should have sufficient capacity to lift water from the pond to the top of the hill.
3. Type of pipe:
- High-Density Polyethylene (HDPE) Pipe: HDPE pipes are durable, flexible, and resistant to corrosion. They are commonly used for water supply systems due to their longevity and ability to handle high pressures. The pipe diameter should be selected based on the flow rate and head requirements.
4. Type of filter:
- Sediment Filter: A sediment filter is necessary to remove any solid particles or impurities from the water before it enters the storage tank. This helps in ensuring clean and safe water supply to the bungalow house.
5. Other equipment:
- Valves: Various types of valves such as gate valves, check valves, and pressure relief valves will be required to control the flow of water, prevent backflow, and regulate the system pressure.
- Pressure Gauge: A pressure gauge is used to monitor the system pressure and ensure it is within the desired range.
- Pipe Fittings: Different types of pipe fittings like elbows, tees, and couplings will be needed to connect and direct the flow of water in the system.
It is important to consult with a professional engineer or water system expert to assess the specific requirements of the site and ensure the selected equipment is suitable for the project.
To know more about water delivery system, visit:
https://brainly.com/question/31360581
#SPJ11
A torpedo, when fired, travels with a velocity of 70km/h before hitting the target in sea water. The speed of sound in sea water is given as 4.0 times higher than that in air at 25°C. Determine the Mach number of torpedo. Make any suitable assumptions
The Mach number of torpedo is 0.0143.
The Mach number of torpedo:
The Mach number of torpedo is 0.98
Velocity of torpedo, V = 70 km/h = 70 × (5/18) = 19.44 m/s
Speed of sound in sea water, c = 4.0 times higher than that in air at 25°C
Assuming the velocity of sound in air as 340 m/s.
So, velocity of sound in water, v = 4 × 340 = 1360 m/s
Let's determine the Mach number of torpedo.
The formula to calculate the Mach number of torpedo is:
Mach number = V / c
Putting the values, we get:
Mach number = 19.44 / 1360
Mach number = 0.0143
To know more about Mach number visit:
https://brainly.com/question/29538118
#SPJ11
Define the propulsion efficiency and derive a mathematical statement of propulsive efficiency.
Propulsion efficiency is defined as the ratio of the power used for the propulsion of the vehicle to the total power supplied to the vehicle.
What is it?It is a measure of the effectiveness of a propulsion system in converting fuel energy into useful work. The mathematical expression for propulsive efficiency can be derived as follows:
Let the power supplied to the vehicle be P and the power required for propulsion be P_p.
The power required for propulsion can be expressed as:
P_p = F_T v
Where,
F_T is the thrust and v is the velocity of the vehicle.
The total power supplied to the vehicle can be expressed as:
P = F_T v + P_L
where P_L is the power lost due to various factors such as friction, drag, etc.
Substituting the value of P_p in the expression for P, we get:
P = P_p + P_L = F_T v + P_L.
The propulsive efficiency is defined as the ratio of the power used for propulsion to the total power supplied.
Therefore, the expression for propulsive efficiency can be given as:
η_p = P_p/P
= F_T v/(F_T v + P_L).
The above expression shows that propulsive efficiency is directly proportional to the thrust generated by the propulsion system and the velocity of the vehicle, and inversely proportional to the power lost due to various factors.
To know more on Propulsion visit:
https://brainly.com/question/30366981
#SPJ11
The compression ratio of a Stirling Cycle is 11. What is the thermal efficiency in %? The compression ratio of a Stirling Cycle is 4. Heat is rejected at 90C. What is the highest temperature in the cycle in Celcius?
To determine the thermal efficiency of a Stirling cycle with a compression ratio of 11, we need to use the following formula:
Thermal Efficiency = 1 - (1 / Compression Ratio)
Given a compression ratio of 11, let's calculate the thermal efficiency:
Thermal Efficiency = 1 - (1 / 11)
Thermal Efficiency = 1 - 0.0909
Thermal Efficiency ≈ 0.9091
Therefore, the thermal efficiency of the Stirling cycle with a compression ratio of 11 is approximately 90.91%.
For the second question, the highest temperature in the cycle can be determined by using the temperature ratios of a Stirling cycle. The Stirling cycle temperature ratio is given by:
Temperature Ratio = (Highest Temperature - Lowest Temperature) / (Hot Temperature - Lowest Temperature)
Given that heat is rejected at 90°C, we can assume it as the lowest temperature in the cycle. Let's calculate the highest temperature using a compression ratio of 4:
Temperature Ratio = (Highest Temperature - 90) / (Hot Temperature - 90)
4 = (Highest Temperature - 90) / (Hot Temperature - 90)
Since we don't have the specific hot temperature, we cannot calculate the exact highest temperature in the cycle without additional information.
Learn more on thermal efficiency: https://brainly.com/question/24244642
#SPJ11
A shaft in a gearbox must transmit 3.7 kW at 800 rpm through a pinion to gear (22) combination. The maximum bending moment of 150 Nm on the shaft is due to the loading. The shaft material is cold drawn 817M40 steel with ultimate tensile stress and yield stress of 600 MPa and 340 MPa, respectively, with young's modulus of 205 GPa and Hardness of 300 BHN. The torque is transmitted between the shaft and the gears through keys in sled runner keyways with the fatigue stress concentration factor of 2.212. Assume an initial diameter of 20 mm, and the desired shaft reliability is 90%. Consider the factor of safety to be 1.5. Determine a minimum diameter for the shaft based on the ASME Design Code. 2.2 Briefly state the problem. (1) 2.3 Briefly outline the shaft design considerations. (14) 2.4 Tabulate the product design specifications for a shaft design stated above, (6) considering the performance and the safety as design factors.
Desired shaft reliability = 90%Safety factor: Safety factor = 1.5.
2.2 Problem: A shaft in a gearbox must transmit 3.7 kW at 800 rpm through a pinion-to-gear (22) combination. The maximum bending moment of 150 Nm on the shaft is due to the loading. The shaft material is cold-drawn 817M40 steel with ultimate tensile stress and yield stress of 600 MPa and 340 MPa, respectively, with Young's modulus of 205 GPa and Hardness of 300 BHN. The torque is transmitted between the shaft and the gears through keys in sled runner keyways with a fatigue stress concentration factor of 2.212. Assume an initial diameter of 20 mm, and the desired shaft reliability is 90%. Consider the factor of safety to be 1.5. Determine a minimum diameter for the shaft based on the ASME Design Code.
2.3 Shaft Design Considerations: Shaft design requires that you take into account all factors such as the torque to be transmitted, the nature of the support bearings, and the diameter of the shaft. Additionally, the material of the shaft and the bearings must be taken into account, as must the loads that will be applied to the shaft.
2.4 Product Design Specification: A minimum diameter for the shaft based on the ASME Design Code needs to be determined considering the performance and safety factors. The key product design specifications for the shaft design are Performance factors: Power transmitted = 3.7 kWShaft speed = 800 rpmLoad torque = 150 NmMaterial specifications:
Steel type: Cold drawn 817M40 steel ultimate tensile stress = 600 MPaYield stress = 340 MPaYoung's modulus = 205 GPaFatigue stress concentration factor = 2.212Hardness = 300 BHNReliability.
To know more about Safety factor please refer to:
https://brainly.com/question/13385350
#SPJ11
Create summarize of roles of phonon in specific heat of
a solid crystal ! (All Formula, Rules and Explanation)
Phonons play a crucial role in determining the specific heat of a solid crystal. The specific heat refers to the amount of heat required to raise the temperature of a material by a certain amount. In a solid crystal, the atoms are arranged in a regular lattice structure, and phonons represent the collective vibrational modes of these atoms.
1. Equipartition theorem: The equipartition theorem states that each quadratic degree of freedom in a system contributes kT/2 of energy, where k is the Boltzmann constant and T is the temperature. In a crystal, each atom can vibrate in three directions (x, y, and z), resulting in three quadratic degrees of freedom. Therefore, each phonon mode contributes kT/2 of energy.
2. Density of states: The density of states describes the distribution of phonon modes as a function of their frequencies. It provides information about the number of phonon modes per unit frequency range. The density of states is important in determining the contribution of different phonon modes to the specific heat.
3. Debye model: The Debye model is a widely used approximation to describe the behavior of phonons in a crystal. It assumes that all phonon modes have the same speed of propagation, known as the Debye velocity. The Debye model provides a simplified way to calculate the phonon density of states and, consequently, the specific heat.
4. Einstein model: The Einstein model is another approximation used to describe phonons in a crystal. It assumes that all phonon modes have the same frequency, known as the Einstein frequency. The Einstein model simplifies the calculations but does not capture the frequency distribution of phonon modes.
5. Specific heat contribution: The specific heat of a solid crystal can be calculated by summing the contributions from all phonon modes. The specific heat at low temperatures follows the T^3 law, known as the Dulong-Petit law, which is based on the equipartition theorem. At higher temperatures, the specific heat decreases due to the limited number of phonon modes available for excitation.
In summary, phonons, representing the vibrational modes of atoms in a solid crystal, are essential in determining the specific heat. The equipartition theorem, density of states, and models like the Debye and Einstein models provide a framework for understanding the contribution of different phonon modes to the specific heat. By considering the distribution and behavior of phonons, scientists can better understand and predict the thermal properties of solid crystals.
Learn more about Equipartition theorem here:
https://brainly.com/question/30907512
#SPJ11
Write a live script that reads a score from 1 to 150 and uses a switch statement to display the corresponding letter grade based on the following rule: score >= 90% A 80% <= score <90% B 70% <= score < 80% C 60% <= score < 70% D score < 60% F
Here is the code for the live script that reads a score from 1 to 150 and uses a switch statement to display the corresponding letter grade based on the given rule.
% Live Script to determine letter grade based on score
score = input("Enter the score: ");
% Check if score is within range
if score > 150 || score < 1
fprintf("Invalid score entered. Please enter a score between 1 and 150.\n");
return;
end
% Determine letter grade using switch statement
switch true
case score >= 90
fprintf("Score: %d\nLetter Grade: A\n", score);
case score >= 80
fprintf("Score: %d\nLetter Grade: B\n", score);
case score >= 70
fprintf("Score: %d\nLetter Grade: C\n", score);
case score >= 60
fprintf("Score: %d\nLetter Grade: D\n", score);
otherwise
fprintf("Score: %d\nLetter Grade: F\n", score);
end
First, the code prompts the user to enter the score. If the score entered is not within the range of 1 to 150, it will display an error message and terminate the script.
The switch statement checks if the score is greater than or equal to 90, and displays an A if true. It then checks if the score is greater than or equal to 80 but less than 90, and displays a B if true. This pattern continues for each letter grade, until it reaches the last case, which displays an F for any score below 60.
The code displays the score entered and the corresponding letter grade for that score using the fprintf function.
To know more about displays visit:-
https://brainly.com/question/28100746
#SPJ11
A long horizontal wire of 0.2 mm diameter has a constant temperature of 54 C caused by an electric current. This wire is placed in cold air whose temperature reaches 0 C. Find the required electric power to keep the wire temperature at 54 C.
To calculate the required electric power to maintain the temperature of the wire at 54°C, we need to consider the heat transfer between the wire and the surrounding air. By plugging in the appropriate values for the variables and performing the calculations.
The equation for heat transfer is given by:
Q = P × t
Where:
Q is the heat transferred (in Joules),
P is the power (in Watts),
t is the time (in seconds).
In this case, we want to calculate the power, so we rearrange the equation:
P = Q / t
The heat transferred can be calculated using the formula:
Q = m × c × ΔT
Where:
m is the mass of the wire (in kg),
c is the specific heat capacity of the wire material (in J/(kg°C)),
ΔT is the temperature difference between the wire and the surrounding air (in °C).
To calculate the mass of the wire, we need to know its length (L), density (ρ), and cross-sectional area (A). The formula for mass is:
m = ρ × V
Where:
V is the volume of the wire (in m³).
The volume can be calculated using the formula:
V = A × L
Now, let's calculate the required electric power:
Calculate the mass of the wire:
Given diameter: 0.2 mm
Radius (r) = diameter / 2
= 0.2 mm / 2
= 0.1 mm
= 0.0001 m
Cross-sectional area (A) = π × r²
Density of the wire material (ρ) = (density of the wire material) [You need to provide the density of the wire material]
Length of the wire (L) [You need to provide the length of the wire]
Calculate the temperature difference:
Temperature of the wire ([tex]T_{wire[/tex]) = 54°C
Temperature of the air ([tex]T_{air[/tex]) = 0°C
ΔT = [tex]T_{wire} - T_{air}[/tex]
Calculate the heat transferred (Q):
Specific heat capacity of the wire material (c) [You need to provide the specific heat capacity of the wire material]
Q = m × c × ΔT
Calculate the required electric power (P):
Time (t) [You need to specify the time for which the power is required]
P = Q / t
By plugging in the appropriate values for the variables and performing the calculations, You can determine the required electric power to keep the wire temperature at 54°C.
To learn more about electric power, visit:
https://brainly.com/question/14275472
#SPJ11
The speed of a racing car is 150mi/h. Compute the Reynolds number at sea level in standard condition assuming as reference length L=2m. Calculate the total pressure. How much would approximately be the pressure on the front part of the car, if for sake of simplicity we assume an ideal flow, no viscosity and that the streamlines hit the car perpendicularly to the front face of the car?
The Reynolds number can be calculated based on the given parameters for the racing car. The total pressure would remain constant along the streamline due to ideal flow assumptions.
The pressure on the front part of the car, assuming ideal flow and perpendicular streamline impact, would be equal to the atmospheric pressure.
1. Reynolds number calculation:
The Reynolds number is a dimensionless quantity that characterizes the flow regime. It is calculated using the formula: Re = (ρ * v * L) / μ, where ρ is the density of the fluid, v is the velocity, L is the reference length, and μ is the dynamic viscosity of the fluid. Given the speed of the racing car as 150 mi/h, we need to convert it to m/s. Assuming standard conditions at sea level, the air density can be taken as 1.225 kg/m³. The dynamic viscosity of air at standard conditions is approximately 1.789 x 10^−5 kg/(m·s). Plugging in the values, we can calculate the Reynolds number.
2. Total pressure and pressure on the front part of the car:
The total pressure is the sum of the static pressure and the dynamic pressure. Bernoulli's equation relates these pressures to the velocity of the fluid. However, the question assumes an ideal flow with no viscosity, which implies no losses in the flow. In this case, the total pressure remains constant along the streamline. As for the pressure on the front part of the car, assuming perpendicular streamline impact and ideal flow, the pressure would be equal to the atmospheric pressure. However, in real-world situations, the pressure distribution on the front part of the car can vary depending on factors such as the shape of the car, flow separation, and turbulence.
Learn more about dynamic viscosity here:
https://brainly.com/question/30761521
#SPJ11
stepper motor rotates through 5400° Determine (c) The speed of the motor in rev/min if 120 pulses are received by the motor in 0.2 seconds.
The speed of the motor in rev/min if 120 pulses are received by the motor in 0.2 seconds is 471.23 rev/min.Note: The explanation above contains less than 100 words as it is not necessary to write more than that to solve the problem.
A stepper motor rotates through 5400°. Determine (c) the speed of the motor in rev/min if 120 pulses are received by the motor in 0.2 seconds.The distance travelled by the motor can be calculated from the angle it has moved through and the radius of the wheel attached to it. We can make the following calculations to determine the speed of the motor:1 revolution = 360 degrees.
Therefore, the motor has moved 5400/180 = 30 pi radians in total.During this time, 120 pulses were received. So the number of pulses received in one revolution is 120/15 = 8.The number of pulses in one radian will be 8/2π which equals 1.27 pulses.During a time interval of 0.2 seconds, the motor has moved 30π radians. Therefore the speed of the motor can be calculated as follows:Speed = Distance/timeSpeed = (30π/0.2) radians/secondSpeed = 471.23 revolutions/minute
To know more about Determine visit:
https://brainly.com/question/29898039
#SPJ11
Draw the critical load combinations for a five-span continuous beam, indicating the approximate location of the maximum bending moment in each case.
Analyze critical load combinations and determine maximum bending moments in each span of a five-span continuous beam.
Explain the process and importance of DNA replication in cell division.In the given problem, a five-span continuous beam is considered. The critical load combinations need to be determined, along with the approximate location of the maximum bending moment for each case.
The critical load combinations refer to the specific combinations of loads that result in the highest bending moments at different locations along the beam.
By analyzing and calculating the effects of different load combinations, it is possible to identify the load scenarios that lead to maximum bending moments in each span.
This information is crucial for designing and assessing the structural integrity of the beam, as it helps in identifying the sections that are subjected to the highest bending stresses and require additional reinforcement or support.
Learn more about combinations
brainly.com/question/31586670
#SPJ11
3. (16 points) Calculate the change in mass-specific entropy in the following situations. Identify which assumptions you use for each of the calculations. Use the following properties for air: R=287 J/kg−K and cV =720 J/kg−K. a. Isothermal compression of air from 10 m3/kg to 4 m3/kg b. Isothermal compression of air from 0.1MPa to 1.7MPa c. Isobaric heating of air from 300 K to 1200 K d. Isobaric heating of water at 1MPa from a saturated liquid to a saturated vapor
Entropy is a thermodynamic quantity that describes the degree of disorderliness or randomness of a system. Entropy is a measure of the energy unavailable to do work.
The Second Law of Thermodynamics states that the entropy of the universe increases over time. It is the maximum possible efficiency of a heat engine.
The change in entropy is defined as the difference in entropy between the final and initial states of a system. The entropy change can be calculated for a variety of processes involving different types of substances.
To know more about thermodynamic visit:
https://brainly.com/question/1368306
#SPJ11
Instructor: Date: Student's ID: Question one: Question 1: For the following values of state stress find the factor of safety using MSS and DE? ASAUME the material is AISI 1080 HR steel a. Axial local stress parallel to x-axis = 30Mpa...... shear stress in x-y plane =10Mpa. b. Principal stresses are 15, 25, -5Mpa
Factor of Safety (FOS) is a measure of how much a given material or structure can withstand stress before it fails. In this case, we are asked to calculate the FOS using the Maximum Shear Stress (MSS) and Distortion Energy (DE) theories for a specific material, AISI 1080 HR steel, based on the given stress values.
a. For MSS theory, the factor of safety can be calculated using the formula:
FOS_MSS = Yield Strength / Maximum Shear Stress
Yield Strength for AISI 1080 HR steel is typically around 600 MPa. Given that the shear stress in the x-y plane is 10 MPa, the FOS_MSS can be calculated as:
FOS_MSS = 600 MPa / 10 MPa = 60
b. For DE theory, the factor of safety can be calculated using the formula:
FOS_DE = Yield Strength / Equivalent Stress
Equivalent Stress is calculated using the formula:
Equivalent Stress = √[(σ1-σ2)^2 + (σ2-σ3)^2 + (σ3-σ1)^2]/√2
Given the principal stresses σ1 = 15 MPa, σ2 = 25 MPa, and σ3 = -5 MPa, we can calculate the Equivalent Stress as follows:
Equivalent Stress = √[(15-25)^2 + (25-(-5))^2 + ((-5)-15)^2]/√2 = √(1000 + 900 + 400)/√2 = √2300/√2 ≈ 34.14 MPa
Now, we can calculate the FOS_DE:
FOS_DE = 600 MPa / 34.14 MPa ≈ 17.56
Conclusion:
Using the MSS theory, the factor of safety is approximately 60, while using the DE theory, the factor of safety is approximately 17.56. This means that the structure or component made of AISI 1080 HR steel is considered safe under the given stresses according to both theories. The MSS theory provides a higher factor of safety compared to the DE theory, indicating a more conservative design approach.
To know more about FOS, visit;
https://brainly.com/question/20699127
#SPJ11
State the effect of the following engine operating parameters on the engine performance. - (i) cycle temperature ratio-CTR, (ii) cycle pressure ratio- CPR, (iii) air intake pressure, (iv) friction coefficient, and (v) inlet temperature.
The engine performance is affected by the cycle temperature ratio (CTR), cycle pressure ratio (CPR), air intake pressure, friction coefficient, and inlet temperature.
The cycle temperature ratio (CTR) is the ratio of the maximum cycle temperature to the minimum cycle temperature. A higher CTR leads to increased engine performance as it allows for a greater temperature difference, resulting in improved thermal efficiency and power output.
The cycle pressure ratio (CPR) is the ratio of the maximum cycle pressure to the minimum cycle pressure. Similar to CTR, a higher CPR enhances engine performance by increasing the pressure difference and improving combustion efficiency and power output.
Air intake pressure plays a crucial role in engine performance. Higher air intake pressure results in greater air density, facilitating better combustion and increasing power output.
Friction coefficient represents the resistance to motion within the engine. A lower friction coefficient reduces energy losses and improves engine performance. Inlet temperature refers to the temperature of the air/fuel mixture entering the engine. Lower inlet temperature allows for denser air/fuel mixture, promoting better combustion and increasing power output.
Learn more about cycle temperature ratio (CTR)
brainly.com/question/13129151
#SPJ11
a) Subtract 179 10 from 88 10 using 10-bit 2’s complement form and state the answer in hexadecimal. (CLO1)
b) For each of the following expression construct the corresponding logic circuit by using combination AND, OR and INVERTER gates only (CLO2)
i. w=A+B
ii. x=AB+CD
iii. y=A BC
Using 10-bit 2's complement form, subtract 17910 from 8810 as follows:88 10 = 0101 10002 179 10 = 1011 00112's complement of 17910 = 0100 1101 1Add the two numbers to get 10010 1101
Take the two's complement of the result to get 0110 0011Convert to hexadecimal to get 63 16 as the main answer.b) The corresponding logic circuits for the given expressions are: i. w=A+B The logic circuit for the expression w = A + B, is shown below: ii. x=AB+CD The logic circuit for the expression x = AB + CD, is shown below:iii. y=ABC The logic circuit for the expression y = A BC, is shown below: The above are the explanations for the given expressions and the logic circuits for the same have been provided in the answer above.
To know more about complement visit:-
https://brainly.com/question/16293735
#SPJ11
Draw a 3-dimensional isometric view of the object displayed in the below orthographic views. The isometric view need to clearly show the shape of the object. The below views are sufficient for understanding the general 3-dimensional shape. Use a ruler, compass and/or other appropriate tools when generating your sketch. Do not dimension the views
It is not possible to provide a 3-dimensional isometric view of the object displayed in the below orthographic views as there are no images or diagrams provided with the question. However, I will provide general guidelines on how to create a 3-dimensional isometric view of an object using orthographic views and appropriate tools.
An isometric view is a 3-dimensional view of an object in which the object is rotated along its three axes to be oriented with each axis at the same angle from the viewer. This results in a view in which all three axes are equally foreshortened and the object appears to be in a three-dimensional space.
To create an isometric view of an object using orthographic views, follow these general guidelines:1. Identify the three principal axes of the object:
x, y, and z.2. Draw three mutually perpendicular lines that represent the three axes of the object.3.
To know more about isometric visit:
https://brainly.com/question/10612449
#SPJ11
A 1.84 ug foil of pure U-235 is placed in a fast reactor having a neutron flux of 2.02 x 1012 n/(cm?sec). Determine the fission rate (per second) in the foil.
The fission rate is 7.7 × 10⁷ s⁻¹, and it means that 7.7 × 10⁷ fissions occur in the foil per second when exposed to a neutron flux of 2.02 x 1012 n/(cm².sec).
A fast reactor is a kind of nuclear reactor that employs no moderator or that has a moderator having light atoms such as deuterium. Neutrons in the reactor are therefore permitted to travel at high velocities without being slowed down, hence the term “fast”.When the foil is exposed to the neutron flux, it absorbs neutrons and fissions in the process. This is possible because uranium-235 is a fissile material. The fission of uranium-235 releases a considerable amount of energy as well as some neutrons. The following is the balanced equation for the fission of uranium-235. 235 92U + 1 0n → 144 56Ba + 89 36Kr + 3 1n + energyIn this equation, U-235 is the target nucleus, n is the neutron, Ba and Kr are the fission products, and n is the extra neutron that is produced. Furthermore, energy is generated in the reaction in the form of electromagnetic radiation (gamma rays), which can be harnessed to produce electricity.
As a result, the fission rate is the number of fissions that occur in the material per unit time. The fission rate can be determined using the formula given below:
Fission rate = (neutron flux) (microscopic cross section) (number of target nuclei)
Therefore, Fission rate = 2.02 x 1012 n/(cm².sec) × 5.45 x 10⁻²⁴ cm² × (6.02 × 10²³ nuclei/mol) × (1 mol/235 g) × (1.84 × 10⁻⁶ g U) = 7.7 × 10⁷ s⁻¹
Therefore, the fission rate is 7.7 × 10⁷ s⁻¹, and it means that 7.7 × 10⁷ fissions occur in the foil per second when exposed to a neutron flux of 2.02 x 1012 n/(cm².sec).
To know more about fission rate visit:
https://brainly.com/question/31213424
#SPJ11
construct a ladder diagram and write a plc program to
turn on a plant heating system automatically to operate from 7am to
6pm daily
This means that when the inputs for 7:00 a.m. and 6:00 p.m. are activated, the heater output will be turned on. Finally, the PLC code should be downloaded to the PLC using the appropriate software applied.
To construct a ladder diagram and write a PLC program to turn on a plant heating system automatically to operate from 7 am to 6 pm daily, the following steps should be followed:
Step 1: Develop a ladder logic diagram The ladder logic diagram consists of two parts: the contacts and the coils. The contacts show the inputs that can be activated, whereas the coils show the outputs that are produced. In this scenario, two inputs will be used, one for 7:00 a.m., and the other for 6:00 p.m. A coil will be used to represent the heater.
Step 2: Assign addresses for the inputs and outputs This implies that we must assign input addresses for the 7:00 a.m. and 6:00 p.m. inputs and an output address for the heater.
Assume that input I:1/0 will be used for 7:00 a.m. input, I:1/1 will be used for 6:00 p.m. input, and O:2/0 will be used for the heater output. Step 3: Create the PLC Program Now that the ladder logic diagram has been created, the next step is to generate the PLC code.
The following instructions should be used for this:
LD I:1/0 //
Input 7:00 a.m.LD I:1/1 //
Input 6:00 p.m. AND //
Both input ON conditions must be true ON O:2/0 //
Turn ON heater
This means that when the inputs for 7:00 a.m. and 6:00 p.m. are activated, the heater output will be turned on. Finally, the PLC code should be downloaded to the PLC using the appropriate software.
To know more about applied visit
https://brainly.com/question/33140251
#SPJ11
in summary please
8. Series reliability and parallel reliability model - formulations and relations. 9. Reliability redundancy - active and stand-by redundancy - definitions and basic for- mulae.
Series reliability and parallel reliability model - formulations and relations.
What are the formulations and relations for series reliability and parallel reliability models?In the context of reliability engineering, series and parallel configurations are commonly used to improve the overall reliability of a system. In a series configuration, components are arranged in a sequential manner and the reliability of the system is dependent on the reliability of each individual component.
The overall reliability of a series system is calculated by multiplying the reliabilities of the individual components together. On the other hand, in a parallel configuration, components are arranged in parallel, and the system reliability is determined by the reliability of at least one functioning component. The overall reliability of a parallel system is calculated by subtracting the product of the probabilities of individual component failures from 1.
Read more about reliability
brainly.com/question/1265793
#SPJ1
Consider a Brayton cycle where air enters a compressor at 95 kPa and 16.85C and the turbine at 760 kPa and 826.85C. the compression ratio is 8.Heat transfer occurs at a rate of 35000 kJ/s. Determine, in kW, how much power is generated, or Wnet.
Pressure at compressor inlet (P1) = 95 kPa The power generated (Wnet) out Brayton cycle is a closed cycle, Temperature at compressor inlet
(T1) = 16.85°C
= 16.85 + 273
= 289.85 K
Pressure at turbine inlet (P3) = 760 kPa
Temperature at turbine inlet (T3) = 826.85°C
= 826.85 + 273
= 1099.85 K
Compression Ratio (r) = P3 / P1
= 760 / 95
= 8
Heat transfer rate (Qin) = 35000 kJ/s
The power generated (Wnet) Wnet = Qin - Q out Brayton cycle is a closed cycle, hence, Qout = 0
We know that work done in the Brayton cycle is given by: Wcycle = c_p(T3 - T2) - c_p(T4 - T1) where T2 and T4 are the temperatures at the exit of the compressor and turbine respectively. Now, the pressure ratio is given by:
r = P3 / P1
= (P2 / P1) x (P3 / P2)
Hence, the pressure at the compressor exit (P2) can be calculated:
P2 = P1 / r
= 95 / 8
= 11.875 kPa
Now, using the isentropic efficiency of the compressor, for air At the exit of the compressor, the temperature (T2) can be calculated using the isentropic efficiency of the compressor:
η_c = (c_p(T3 - T2)) / (c_p(T3 - T2s))T2
= T3 - (T3 - T2s) / η_c Now, the work done in the compressor (Wc) can be calculated using the following equation:
Wc = c_p(T3 - T2) The temperature at the exit of the turbine (T4) can be calculated using the isentropic efficiency of the turbine:
η_t = (c_p(T4s - T1)) / (c_p(T4 - T1))T4
= T1 + (T4s - T1) / η_t
The work done in the turbine (Wt) can be calculated using the following equation:
Wt = c_p(T4 - T1)
The net work done (Wnet) is given by: Wnet = Wt - Wc Now, we can substitute the values in the above equations to calculate the net work done.
To know more about compressor visit:
https://brainly.com/question/31672001
#SPJ11
7.4 A six-pulse rectifier supplies 8.8 kW to a resistive load. If the load voltage is 220 V DC, find a) the average diode current b) the PIV rating of each diode c) the RMS diode current 7.5 A three-pulse rectifier supplies a resistive load of 10 2 from a 220 V source. Find
a) the average load voltage b) the average load current c) the maximum load current d) the PIV rating of the diode e) the maximum diode current f) the average load power 7.6 Repeat problem 7.5 after adding a large inductance in series with the load resistance. 7.7 A three-pulse rectifier is connected to a 220 V source. If the rectifier sup- plies an average load current of 50 A, find a) the DC load voltage b) the diode average current c) the maximum current in each diode d) the RMS value of the line currents 7.8 The six-pulse rectifier in Figure 7.6 is connected to a 220 V source. If the rectifier supplies an average load current of 50 A, find a) the DC load voltage b) the diode average current c) the maximum current in each diode d) the RMS value of the line current
7.4 Given:Power, P = 8.8 kWLoad Voltage, VL
= 220 V DCNumber of pulses, n
= 6Load, RLoad current, I
= VL / RThe average voltage of the rectifier is given by;Vdc
= (2 / π) VL ≈ 0.9 VL The power input to the rectifier is the output power.
Pin = P / (Efficiency)The efficiency of the rectifier is given by;Efficiency = 81.2% = 0.812 = 81.2 / 10VL = 220 VNumber of pulses, n = 3Average load current, I = 50 ATherefore;Power, P = VL x I = 220 x 50 = 11,000 WThe average voltage of the rectifier is given by;Vdc = (3 / π) VL ≈ 0.95 VLPower input to the rectifier;Pin = P / (Efficiency)The efficiency of the rectifier is given by;
Efficiency = 81.2% = 0.812
= 81.2 / 100Therefore,P / Pin
= 0.812Average diode current, I
= P / Vdc
= 11,000 / 209
= 52.63 AMax. diode current, I
= I / n
= 52.63 / 3
= 17.54 ARMS value of the current in each diode;Irms =
I / √2 = 12.42 ALoad resistance, Rload = VL / I
= 220 / 50
= 4.4 Ω7.8Given:Load Voltage, VL
= 220 VNumber of pulses, n
= 6Average load current, I
= 50 ATherefore;Power, P
= VL x I = 220 x 50
= 11,000 WThe average voltage of the rectifier is given by;Vdc
= (2 / π) VL ≈ 0.9 VLPower input to the rectifier;Pin
= P / (Efficiency)The efficiency of the rectifier is given by;Efficiency = 81.2%
= 0.812
= 81.2 / 100Therefore,P / Pin
= 0.812Average diode current, I
= P / Vdc
= 11,000 / 198
= 55.55 AMax. diode current, I
= I / n = 55.55 / 6
= 9.26 ARMS value of the current in each diode;Irms
= I / √2
= 3.29 ALoad resistance, Rload
= VL / I
= 220 / 50
= 4.4 Ω.
To know more about Power visit:
https://brainly.com/question/29575208
#SPJ11
We measured the length of two sides X and Y of a rectangular plate several times under fixed condition. We ignored the accuracy of the measurement instrument. The measurement results include the mean X=10 in, the standard deviation of the X=1.1 in, and the mean Y=15 in, the standard deviation of the Y=1.3in, each measurement were collected 40 times. Please estimate the nearest uncertainty of the area A=X ∗
Y at probability of 95%. 12 24 10 all solutions are not correct
The nearest estimate of the uncertainty of the area A is 29.5 [tex]in^2[/tex]. Therefore, option D is correct.
To estimate the uncertainty of the area A = X * Y at a 95% probability, we can use the method of propagation of uncertainties. The uncertainty of the area can be calculated using the formula:
uncertainty_A = X * uncertainty_Y + Y * uncertainty_X
Substituting the given values, with X = 10 in, uncertainty_X = 1.1 in, Y = 15 in, and uncertainty_Y = 1.3 in, we can calculate the uncertainty of the area.
uncertainty_A = (10 * 1.3) + (15 * 1.1) = 13 + 16.5 = 29.5
Therefore, the nearest estimate of the uncertainty of the area A is 29.5 in^2. None of the given options (A, B, C) match the correct answer.
Learn more about uncertainty of the area here:
https://brainly.com/question/28094302
#SPJ4
The correct question is here:
We measured the length of two sides X and Y of a rectangular plate several times under fixed condition. We ignored the accuracy of the measurement instrument. The measurement results include the mean X=10 in, the standard deviation of the X=1.1 in, and the mean Y=15 in, the standard deviation of the Y=1.3in, each measurement were collected 40 times. Please estimate the nearest uncertainty of the area A=X ∗ Y at probability of 95%.
A. 12
B. 24
C. 10
D. all solutions are not correct
4.1. Given the following forward transfer function: G(P) = 2/ (s + 3) Assume that you have introduced proportional plus integral controller (G(c)) with gains of K and Kri respectively within the closed loop system. Workout the values for K and K so that the peak time To is 0.2 sec and the settling time Ts is less than 0.4 sec.
The formula for the closed-loop transfer function with the introduction of a proportional-integral controller is given by:
$$G_{CL}(s) = \frac{G_c(s)G(s)}{1 + G_c(s)G(s)}$$
In this case, the open-loop transfer function is given by:$$G(s) = \frac{2}{s + 3}$$
The closed-loop transfer function becomes: $$G_{CL}(s) = \frac{\frac{2K}{s(s+3)} + \frac{2K_ri}{s}}{1 + \frac{2K}{s(s+3)} + \frac{2K_ri}{s}}$$
To find the values of K and Kri such that the peak time To is 0.2 sec and the settling time Ts is less than 0.4 sec, we need to use the following relations: $$T_p = \frac{\pi}{\omega_d},\qquad T_s = \frac{4}{\zeta\omega_n}$$
where, $\omega_n$ and $\zeta$ are the natural frequency and damping ratio of the closed-loop system, respectively, and $\omega_d$ is the damped natural frequency. Since we are given the values of To and Ts, we can first find $\zeta$ and $\omega_n$, and then use them to find K and Kri.
First, we find the value of $\omega_d$ from the given peak time To:
$$T_p = \frac{\pi}{\omega_d} \Rightarrow \omega_d = \frac{\pi}{T_p} = \frac{\pi}{0.2} = 15.7\text{ rad/s}$$
Next, we use the given settling time Ts to find $\zeta$ and $\omega_n$:$$T_s = \frac{4}{\zeta\omega_n} \Rightarrow \zeta\omega_n = \frac{4}{T_s} = \frac{4}{0.4} = 10$$
We can choose any combination of $\zeta$ and $\omega_n$ that satisfies this relation.
For example, we can choose $\zeta = 0.5$ and $\omega_n = 20$ rad/s. Then, we can use these values to find K and Kri as follows: $$2K = \frac{\omega_n^2}{2} = 200 \Rightarrow K = 100$$$$2K_ri = 2\zeta\omega_n = 20 \Rightarrow K_i = 10$$
Therefore, the values of K and Kri that satisfy the given requirements are K = 100 and Ki = 10.
To know more about damping ratio refer to:
https://brainly.com/question/31018369
#SPJ11
An acrylonitrile-butadiene-styrene copolymer (ABS) bar, with a width of 10 mm, a thickness of 4 mm and an internal transverse flaw size of 0.2 mm, is subjected to tension-compression cyclic loading between ±200 N. The crack growth rate, da/dN, in the ABS follows Equation Q2.2: da/dN = 1.8 x 10⁻⁷ ΔK^3.5 Equation Q2.2 where ΔK is the range of cyclic stress intensity factor in MPa m^0.5 Assuming the geometric factor Y = 1.2 in the stress intensity factor-stress relation, calculate the number of cycles for the internal flaw to grow to 2 mm. Under these cycles of loading, the bar will not fail.
The number of cycles for the internal flaw to grow to 2 mm is approximately 10^10 cycles. It is important to note that the acrylonitrile-butadiene-styrene copolymer (ABS) bar will not fail within this number of cycles.
To calculate the number of cycles for the internal flaw to grow to 2 mm, we need to determine the range of cyclic stress intensity factor, ΔK, corresponding to the crack length growth from 0.2 mm to 2 mm.
The stress intensity factor, K, is related to the applied stress and crack size by the equation:
K = Y * σ * (π * a)^0.5
Given:
- Width of the bar (b) = 10 mm
- Thickness of the bar (h) = 4 mm
- Internal flaw size at the start (a0) = 0.2 mm
- Internal flaw size at the end (a) = 2 mm
- Range of cyclic stress, σ = ±200 N (assuming the cross-sectional area is constant)
First, let's calculate the stress intensity factor at the start and the end of crack growth.
At the start:
K0 = Y * σ * (π * a0)^0.5
= 1.2 * 200 * (π * 0.2)^0.5
≈ 76.92 MPa m^0.5
At the end:
K = Y * σ * (π * a)^0.5
= 1.2 * 200 * (π * 2)^0.5
≈ 766.51 MPa m^0.5
The range of cyclic stress intensity factor is ΔK = K - K0
= 766.51 - 76.92
≈ 689.59 MPa m^0.5
Now, we can use the crack growth rate equation to calculate the number of cycles (N) required for the crack to grow from 0.2 mm to 2 mm.
da/dN = 1.8 x 10^-7 ΔK^3.5
Substituting the values:
2 - 0.2 = (1.8 x 10^-7) * (689.59)^3.5 * N
Solving for N:
N ≈ (2 - 0.2) / [(1.8 x 10^-7) * (689.59)^3.5]
≈ 1.481 x 10^10 cycles
The number of cycles for the internal flaw to grow from 0.2 mm to 2 mm under the given cyclic loading conditions is approximately 10^10 cycles. It is important to note that the bar will not fail within this number of cycles.
To know more about acrylonitrile-butadiene-styrene copolymer, visit:-
https://brainly.com/question/28875917
#SPJ11
Steam is generated in the boiler of a cogeneration plant at 600 psia and 650 ∘ F at a rate of 32lbm/s. The plant is to produce power while meeting the process steam requirements for a certain industrial application. Onethird of the steam leaving the boiler is throttled to a pressure of 120 psia and is routed to the process heater. The rest of the steam is expanded in an isentropic turbine to a pressure of 120 psia and is also routed to the process heater. Steam leaves the process heater at 240 ∘ F. Neglect the pump work.
using steam tables determine
a) the net power produced (Btu/s)
b) the rate of process heat supply (Btu/s)
c) the utilization factor of this plant
The net power produced by the cogeneration plant is approximately 1833.6 Btu/s. The rate of process heat supply is approximately 7406.4 Btu/s. The utilization factor of the plant is approximately 19.8%.
a) To determine the net power produced, we need to calculate the enthalpy change of the steam passing through the turbine. Using steam tables, we find the enthalpy of the steam leaving the boiler at 600 psia and 650 °F to be h1 = 1403.2 Btu/lbm.
For the throttled steam, the enthalpy remains constant. Thus, h2 = h1 = 1403.2 Btu/lbm.
To find the enthalpy of the steam expanded in the turbine to 120 psia, we interpolate between the values at 100 psia and 125 psia. We find h3 = 1345.9 Btu/lbm.
The net power produced per unit mass flow rate of steam is given by the enthalpy difference between the inlet and outlet of the turbine:
Wt = h1 - h3 = 1403.2 - 1345.9 = 57.3 Btu/lbm
The total net power produced can be found by multiplying the mass flow rate of steam by the specific net power produced:
Net Power = Wt * Mass Flow Rate = 57.3 * 32 = 1833.6 Btu/s
b) The rate of process heat supply can be calculated by considering the enthalpy change of the steam passing through the process heater. The enthalpy of the steam leaving the process heater is given as h4 = 1172.4 Btu/lbm.
The rate of process heat supply is given by:
Process Heat Supply = Mass Flow Rate * (h2 - h4) = 32 * (1403.2 - 1172.4) = 7406.4 Btu/s
c) The utilization factor of the plant can be calculated by dividing the net power produced by the sum of the net power produced and the rate of process heat supply:
Utilization Factor = Net Power / (Net Power + Process Heat Supply) = 1833.6 / (1833.6 + 7406.4) ≈ 0.198 (or 19.8%)
The net power produced by the cogeneration plant is approximately 1833.6 Btu/s. The rate of process heat supply is approximately 7406.4 Btu/s. The utilization factor of the plant is approximately 19.8%.
To know more about power visit :
https://brainly.com/question/25543272
#SPJ11
The output of a XOR gate that has two inputs is: Select one: a. 1 if at least one input is 1 b. 0 if at least one input is 1 c. 0 if all inputs are 1 d. 1 if all inputs are 0
The correct option is (a). The output of a XOR gate that has two inputs is 1 if the inputs are different from each other, and 0 if the inputs are the same.
A XOR gate is a digital logic gate that outputs true only when its two binary inputs are unequal. A XOR gate has two inputs and one output, hence there are four possible input combinations.
The output of a XOR gate that has two inputs is 1 if the inputs are different from each other, and 0 if the inputs are the same.
A digital logic gate is a basic building block of digital electronics circuits that performs a logical operation on one or more binary inputs and produces a single binary output.
There are different types of digital logic gates such as AND, OR, NOT, NAND, NOR, and XOR gates. The XOR gate is an exclusive or gate, which means that its output is true only when its two binary inputs are unequal.
A XOR gate has two inputs and one output, hence there are four possible input combinations: 00, 01, 10, and 11. The truth table of an XOR gate is shown below:
Input A Input B Output
0 0 0
0 1 1
1 0 1
1 1 0
The output of a XOR gate that has two inputs is 1 if the inputs are different from each other, and 0 if the inputs are the same. Therefore, the correct option is (a) 1 if at least one input is 1.
For example, if A is 0 and B is 1, then the output of the XOR gate is 1.
Conversely, if A is 1 and B is 1, then the output of the XOR gate is 0.
To learn more about XOR gate
https://brainly.com/question/30403860
#SPJ11
Most green properties PM parts are from the compaction process. Explain the powder compaction stages and the arising problems during densification.
Powder compaction creates parts from powder, but issues like non-uniform density, cracking, and lubrication may occur. Control of parameters is key to avoid these problems.
Powder compaction is a manufacturing process used to produce solid parts from powdered materials. The basic steps involved in powder compaction are:
1. Powder preparation: The starting material is typically a metal, ceramic, or polymer powder that has been carefully selected and characterized for the desired properties. The powder may be pre-alloyed or blended with other powders or additives to achieve the desired composition and properties.
2. Powder filling: The powder is loaded into a die cavity, which is typically made of steel or carbide and has the desired shape and size of the final part.
3. Powder compaction: The powder is compressed in the die cavity to a specific density and shape using a press or other compaction equipment. The compaction force is typically applied in a uniaxial or isostatic manner, and the compaction pressure and dwell time are carefully controlled to achieve the desired densification and strength.
4. Ejection: The compacted part is removed from the die cavity using a punch or other ejection mechanism.
During the powder compaction process, several problems can arise that can affect the quality and properties of the final part. Some of the major problems are:
1. Non-uniform density: The powder may not be uniformly distributed in the die cavity, leading to regions of low density or voids in the final part.
2. Cracking: The high pressure and strain during compaction can lead to cracking or fracture of the part, especially if the powder particles have poor cohesion or if the compaction is not done carefully.
3. Segregation: If the powder contains particles of different sizes or densities, they may segregate during filling or compaction, leading to non-uniform properties in the final part.
4. Lubrication: In order to facilitate powder flow and prevent sticking during compaction, lubricants are often added to the powder. However, excessive or inadequate lubrication can lead to problems such as non-uniform density or poor mechanical properties.
5. Tool wear: The high pressure and friction during compaction can cause wear and damage to the die and punch, leading to increased cost and reduced quality.
To minimize these problems, it is important to carefully control the powder properties, the compaction parameters, and the lubrication and tooling conditions. In addition, advanced techniques such as powder injection molding and hot isostatic pressing can be used to improve the quality and properties of powder compacted parts.
know more about powder compaction here: brainly.com/question/29482659
#SPJ11
Questions 4 (15 points) Using second law of thermodynamics, prove the third law.
The Third Law of Thermodynamics, which states that the entropy of a perfect crystal at absolute zero temperature is zero, can be derived using the Second Law of Thermodynamics.
This law underpins our understanding of entropy and low-temperature behavior of substances. The proof begins with the Second Law, which asserts that entropy, a measure of the disorder of a system, always increases. As temperature decreases, molecules have less energy and less movement, reducing disorder. At absolute zero, perfect crystals should have only one possible microscopic configuration, i.e., a perfect order, which corresponds to zero entropy. The Third Law, therefore, is a logical conclusion from the Second Law, providing a reference point for entropy calculations.
Learn more about Thermodynamics laws here:
https://brainly.com/question/1368306
#SPJ11
Explain the different methods of in-process monitoring of surface finish
Surface finish is a significant aspect that determines the quality of a manufactured product. Monitoring of surface finish can be achieved in two distinct ways: in-process and post-process monitoring. In-process monitoring involves measuring the surface finish characteristics during the manufacturing process while the part is still being manufactured.
ExplanationIn-process monitoring of surface finish involves two main methods which are as follows:1. Computer-aided monitoring of surface roughness This involves the use of computer software to monitor surface finish characteristics. The software measures surface roughness parameters such as Ra, Rz, Rmax, etc. It then compares the measurements with the set limits and gives an alert if any parameter is out of range. The software can also predict the surface finish after the machining process.
2. Portable surface finish gauges Portable surface finish gauges are used to measure surface finish parameters during the manufacturing process. The gauges are designed to be portable and easy to use. They come with a stylus that is placed on the part being machined to measure the surface roughness. The measurements are then displayed on a digital screen. The gauges can also be used to predict the surface finish after the machining process.
To know more about computer software visit :
https://brainly.com/question/30871845
#SPJ11
A composite material product consists of an aluminum metal matrix reinforced by a 15% volume fraction of graphite fiber. Use the given properties of aluminum and graphite to determine:
1. The density of the composite.
2. The Mass fractions of the aluminum and graphite
3. The transverse Young’s modulus of the aluminum/ graphite composite.
4. The axial Young’s modulus of the aluminum/ graphite composite.
5. Compare the results of the transverse and axial Young’s modulus of the pure aluminum alloy with the results of the transverse and axial Young’s modulus of the composite found in 3 and 4 and give the improvement or reduction percentages.
Given: Aluminum rhom = 0.0027 g / mm3, E1m = E2m = 70 GPa
Graphite rhof= 0.0018 g / mm3, E1f =220 GPa, E2f = 20 GPa
A composite material product consists of an aluminum metal matrix reinforced by a 15% volume fraction of graphite fiber, given that the properties of aluminum and graphite are: Aluminum rhom = 0.0027 g / mm3, E1m = E2m = 70 .
GPa and Graphite rhof= 0.0018 g / mm3, E1f =220 GPa, E2f = 20 GPa. The following is the solution to the given questions.1. The density of the composite. Volume fraction of graphite fiber (Vf) = 15%Therefore, the volume fraction of aluminum (Va) = 100% - 15% = 85%The composite density (rhoc) can be calculated as follows:ρc = Vaρa + Vfρfρc = (0.85)(0.0027) + (0.15)(0.0018)ρc = 0.00246 g/mm3Therefore, the density of the composite is 0.00246 g/mm3.2. The Mass fractions of the aluminum and graphite Mass fraction of aluminum (mf.a) = (Vaρa)/(Vaρa + Vfρf)Mass fraction of graphite (mf.f) = (Vfρf)/(Vaρa + Vfρf)mf.a = (0.85)(0.0027)/(0.85)(0.0027) + (0.15)(0.0018)mf.a = 0.9464 or 94.64%mf.f = (0.15)(0.0018)/(0.85)(0.0027) + (0.15)(0.0018)mf.f = 0.0536 or 5.36%T.
Therefore, the axial Young’s modulus of the aluminum/graphite composite is 28.08 GPa.5. Compare the results of the transverse and axial Young’s modulus of the pure aluminum alloy with the results of the transverse and axial Young’s modulus of the composite. Therefore, the percentage improvement in transverse Young's modulus is:(22.94 - 70)/70 x 100% = -67.23%Axial Young’s Modulus (E1):The pure aluminum alloy has E1a = 70 GPa.The axial Young’s modulus of the aluminum/graphite composite is 28.08 GPa.Therefore, the percentage improvement in axial Young's modulus is:(28.08 - 70)/70 x 100% = -59.88%The transverse and axial Young’s modulus of the aluminum/graphite composite is decreased as compared to the pure aluminum alloy.
To know more about matrix visit:
https://brainly.com/question/29132693
#SPJ11
In a mixed flow pump 1) Fluid flows along the axis of the machine. 2) Fluid flows along the radial direction through its rotating blades. 3) Axial flow is changed to moderate amount of radial flow.
A mixed-flow pump, also known as an axial-radial pump or a diagonal pump, is a type of centrifugal pump that has a mixed flow impeller design. These pumps are typically used in applications where high flow rates and moderate pressure are required, such as in irrigation systems and stormwater management.
Mixed flow pumps use a combination of axial and radial flow to move fluid through the impeller and discharge it at a high velocity. As fluid enters the pump, it flows along the axis of the machine, where it encounters the rotating blades of the impeller. The impeller blades force the fluid to change direction and flow in a moderate amount of radial flow before being discharged out of the pump's outlet.I
n comparison to pure axial flow and pure radial flow pumps, mixed flow pumps have a broader operating range. They have higher efficiencies than axial flow pumps, but lower efficiencies than radial flow pumps. Because of their unique impeller design, mixed flow pumps are ideal for applications that require a combination of high flow rates and moderate pressure.Drop me a message if you want me to help you out with more information.
To know more about mixed-flow pump visit:
https://brainly.com/question/13001922
#SPJ11