The vectors are sin ØQR = (√99) / (3√14).
Given vectors are P = 2ax - az
Q = 2ax - ay + 2az
R = 2ax - 3ay, +az
(a) (P + Q) × (P - Q)
Using the formula, (a × b) × (a × c) = (a·a)bc - (a·b)ac + (a·c)ab
On simplification, we get (P + Q) × (P - Q) = [(2ax - az) + (2ax - ay + 2az)] × [(2ax - az) - (2ax - ay + 2az)] = 4ax × (-ay - az) = -4ax²y - 4ax²z
(P + Q) × (P - Q) = -4ax²y - 4ax²z(b) sin ØQR
We can find sin ØQR using the formula, `|A×B| = |A||B|sin Ø`
where A and B are any two vectors and Ø is the angle between them.
On simplification, we get, `sin Ø = |A×B| / |A||B|
Let's calculate the vector product of vectors Q and R.(Q × R) = (2ax - ay + 2az) × (2ax - 3ay, +az)
On simplification, we get, (Q × R) = -5ax - 7ay - 5az
Let's find the magnitudes of vectors
Q, R, and Q × R|Q| = √(22 + 12 + 22) = √9 = 3|R| = √(22 + (-3)2 + 12) = √14|Q × R| = √(5² + 7² + 5²) = √99
Putting all these values in the formula, `sin Ø = |Q×R| / |Q||R|`
we get `sin Ø = (√99) / (3√14)`
sin ØQR = (√99) / (3√14)
To know more about vectors visit:
https://brainly.com/question/24256726
#SPJ11
Oil is supplied at the flow rate of 13660 mm' to a 60 mm diameter hydrodynamic bearing
rotating at 6000 rpm. The bearing radia clearance is 30 um and its length is 30 mm. The beaning is linder a load of 1.80 kN.
determine temperature rise through the bearing?
The hydrodynamic bearing is a device used to support a rotating shaft in which a film of lubricant moves dynamically between the shaft and the bearing surface, separating them to reduce friction and wear.
Step-by-step solution:
Given parameters are, oil flow rate = 13660 mm3/s
= 1.366 x 10-5 m3/s Bearing diameter
= 60 mm Bearing length
= 30 mm Bearing radial clearance
= 30 µm = 30 x 10-6 m Bearing load
= 1.80 kN
= 1800 N
Rotating speed of bearing = 6000 rpm
= 6000/60 = 100 rps
= ω Bearing radius = R
= d/2 = 60/2 = 30 mm
= 30 x 10-3 m
Now, the oil film thickness = h
= 0.78 R (for well-lubricated bearings)
= 0.78 x 30 x 10-3 = 23.4 µm
= 23.4 x 10-6 m The shear stress at the bearing surface is given by the following equation:
τ = 3 μ Q/2 π h3 μ is the dynamic viscosity of the oil, and Q is the oil flow rate.
Thus, μ = τ 2π h3 / 3 Q = 1.245 x 10-3 Pa.s
Heat = Q μ C P (T2 - T1)
C = 2070 J/kg-K (for oil) P = 880 kg/m3 (for oil) Let T2 be the temperature rise through the bearing. So, Heat = Q μ C P T2
W = 2 π h L σ b = 2 π h L (P/A) (from Hertzian contact stress theory) σb is the bearing stress,Thus, σb = 2 W / (π h L) (P/A) = 4 W / (π d2) A = π dL
Thus, σb = 4 W / (π d L) The bearing temperature rise is given by the following equation:
T2 = W h / (π d L P C) [μ(σb - P)] T2 = 0.499°C.
To know more about hydrodynamic visit:
https://brainly.com/question/10281749
#SPJ11
1) Determine if the system described by y[n] =α+ x + x[n + 1] + x[n] + x[n − 1] + x [n - 2] is (a) linear, (b) causal, (c) shift-invariant, and (d) stable.
2) Determine if the system described by y[n] = x[n + 1] + x[n] + x[n − 1] + x[n-2] is causal.
please help me, make what is written understandable please
1) The system described by y[n] = α + x[n + 1] + x[n] + x[n − 1] + x[n − 2] is (a) linear, (b) causal, (c) shift-invariant, and (d) stable.(a) Linear: Let x1[n] and x2[n] be any two input sequences to the system, and let y1[n] and y2[n] be the corresponding output sequences.
Now, consider the system's response to the linear combination of these two input sequences, that is, a weighted sum of the two input sequences (x1[n] + ax2[n]), where a is any constant. For this input, the output of the system is y1[n] + ay2[n]. Thus, the system is linear.(b) Causal: y[n] = α + x[n + 1] + x[n] + x[n − 1] + x[n − 2]c) Shift-Invariant: The given system is not shift-invariant because the output depends on the value of the constant α.
(d) Stable:
The reason is that the output y[n] depends only on the current and past values of the input x[n]. The system is not shift-invariant since it includes the value x[n+1].
To know more about shift-invariant visit:
https://brainly.com/question/31668314
#SPJ11
1. (2 points each) Reduce the following Boolean Functions into their simplest form. Show step-by-step solution. A. F=[(X ′
Y) ′ +(YZ ′ ) ′ +(XZ) ′ ] B. F=[(AC ′ )+(AB ′ C)] ′ [(AB+C) ′ +(BC)] ′ +A ′ BC 2. (3 points each) I. Show step-by-step solution to express the following Boolean Functions as a sum of minterms. II. Draw the Truth Table. III. Express the function using summation ( ( ) notation. A. F=A+BC ′ +B ′ C+A ′ BC B. F=X ′ +XZ+Y ′ Z+Z
The simplified form of Boolean function F is F = X' + Y' + Z'.
The simplified form of Boolean function F is F = AC + A'BC.
A. F = [(X'Y)' + (YZ)' + (XZ)']'
Step 1: De Morgan's Law
F = [(X' + Y') + (Y' + Z') + (X' + Z')]
Step 2: Boolean function
F = X' + Y' + Z'
B. F = [(AC') + (AB'C)]'[(AB + C)' + (BC)]' + A'BC
Step 1: De Morgan's Law
F = (AC')'(AB'C')'[(AB + C)' + (BC)]' + A'BC
Step 2: Double Complement Law
F = AC + AB'C [(AB + C)' + (BC)]' + A'BC
Step 3: Distributive Law
F = AC + AB'C AB' + C'' + A'BC
Step 4: De Morgan's Law
F = AC + AB'C [AB' + C'](B + C')' + A'BC
Step 5: Double Complement Law
F = AC + AB'C [AB' + C'](B' + C) + A'BC
Step 6: Distributive Law
F = AC + AB'C [AB'B' + AB'C + C'B' + C'C] + A'BC
Step 7: Simplification
F = AC + AB'C [0 + AB'C + 0 + C] + A'BC
Step 8: Identity Law
F = AC + AB'C [AB'C + C] + A'BC
Step 9: Distributive Law
F = AC + AB'CAB'C + AB'CC + A'BC
Step 10: Simplification
F = AC + 0 + 0 + A'BC
Know more about Boolean function here:
brainly.com/question/27885599
#SPJ4
Assuming initial rest conditions, find solutions to the model equations given by:
q1+ a2q1 = P1(t)
q2+b2q2= P2(t)
where P(t)= 17 and P2(t) = 12. Note that =w, and b = w2 (this is done to ease algebraic entry below).
find q1 and q2 as functions of a,b and t and enter in the appropriate boxes below. Help with algebraic entry can be found by clicking on the blue question marks.
q1(t)=
q2(t) =
q1(t) = (17/ω) * sin(ωt)
q2(t) = (12/ω) * sin(ωt)
Explanation:
The given model equations are:
q1 + a2q1 = P1(t)
q2 + b2q2 = P2(t)
Where P(t) = 17 and P2(t) = 12. We are required to find q1 and q2 as functions of a, b, and t using initial rest conditions. Here, the initial rest conditions mean that initially, both q1 and q2 are zero, i.e., q1(0) = 0 and q2(0) = 0 are known.
Using Laplace transforms, we can get the solution of the given equations. The Laplace transform of q1 + a2q1 = P1(t) can be given as:
L(q1) + a2L(q1) = L(P1(t))
L(q1) (1 + a2) = L(P1(t))
q1(t) = L⁻¹(L(P1(t))/(1 + a2))
Similarly, the Laplace transform of q2 + b2q2 = P2(t) can be given as:
L(q2) + b2L(q2) = L(P2(t))
L(q2) (1 + b2) = L(P2(t))
q2(t) = L⁻¹(L(P2(t))/(1 + b2))
Substituting the given values, we get:
q1(t) = L⁻¹(L(17)/(1 + ω2))
q1(t) = 17/ω * L⁻¹(1/(s2 + ω2))
q1(t) = (17/ω) * sin(ωt)
q2(t) = L⁻¹(L(12)/(1 + ω2))
q2(t) = 12/ω * L⁻¹(1/(s2 + ω2))
q2(t) = (12/ω) * sin(ωt)
Hence, the solutions to the given model equations are:
q1(t) = (17/ω) * sin(ωt)
q2(t) = (12/ω) * sin(ωt)
To know more about Laplace transforms here:
https://brainly.com/question/30759963
#SPJ11
An inductor L resitor R1 of value 5 and resistor R2 of value 10 are connected in series with a of valtage source of value V(t) = 50 cos wt. If the power consumed by the R1 resistor is 10 W, calculate the power factor of the circuit.
The power factor of the circuit is 0.06.
The power factor (PF) of the circuit can be calculated using the following formula:
PF = P / (V * I)
where P is the active power consumed by the resistor R₁, V is the voltage amplitude, and I is the current amplitude.
Given:
Resistor R₁ value (R₁) = 5 Ω
Resistor R₂ value (R₂) = 10 Ω
Voltage source value (V(t)) = 50 cos(ωt)
Active power consumed by R₁ (P) = 10 W
To calculate the power factor, we need to find the current amplitude (I). Since the circuit consists of resistors only, the current will be the same throughout the circuit.
Using Ohm's Law, we can calculate the current:
I = V / R
= 50 / (R₁ + R₂)
= 50 / (5 + 10)
= 50 / 15
= 10/3 A
Now, we can calculate the power factor (PF):
PF = P / (V * I)
= 10 / (50 * 10/3)
= 10 / (500/3)
= 30/500
= 0.06
Learn more about power factor
https://brainly.com/question/11957513
#SPJ11
If the allowable deflection of a warehouse is L/180, how much is a 15' beam allowed to deflect? 0.0833 inches o 1 inch 1.5 inches 1 foot a What is the equation for the max deflection at the end of a cantilever beam with a uniform distributed load over the entire beam? -5wL44/384E1 -PL^3/48EI -PL^3/3EI O-WL4/8E1
If the allowable deflection of a warehouse is L/180, we need to determine the maximum deflection of a 15' beam. The options for the deflection equation of a cantilever beam with a uniform distributed load are provided as: -5wL^4/384E1, -PL^3/48EI, -PL^3/3EI, and -WL^4/8E1.
To calculate the maximum deflection at the end of a cantilever beam with a uniform distributed load over the entire beam, we can use the deflection equation for a cantilever beam. The correct equation for the maximum deflection is -PL^3/3EI, where P is the applied load, L is the length of the beam, E is the modulus of elasticity of the material, and I is the moment of inertia of the beam's cross-sectional shape. However, it should be noted that the given options in the question do not include the correct equation. Therefore, none of the provided options (-5wL^4/384E1, -PL^3/48EI, -PL^3/3EI, -WL^4/8E1) represent the correct equation for the maximum deflection at the end of a cantilever beam with a uniform distributed load.
Learn more about maximum deflection here:
https://brainly.com/question/32774334
#SPJ11
A body in uniaxial tension has a maximum principal stress of 20 MPa. If the body's stress state is represented by a Mohr circle, what is the circle's radius? a 20 MPa bb 5 MPa c 2 MPa d 10 MPa
The radius of the Mohr circle represents half of the difference between the maximum and minimum principal stresses. 10 MPa is the correct answer
The radius of a Mohr circle represents the magnitude of the maximum shear stress. In uniaxial tension, the maximum shear stress is equal to half of the difference between the maximum and minimum principal stresses. Since the maximum principal stress is given as 20 MPa, the minimum principal stress in uniaxial tension is zero.
In this case, the maximum principal stress is given as 20 MPa. Since the stress state is uniaxial tension, the minimum principal stress is zero.
Therefore, the radius of the Mohr circle is:
Radius = (σ₁ - σ₃) / 2
Since σ₃ = 0, the radius simplifies to:
Radius = σ₁ / 2
Substituting the given value of σ₁ = 20 MPa, we have:
Radius = 20 MPa / 2 = 10 MPa
Therefore, the radius of the Mohr circle representing the body's stress state is 10 MPa.
Option (d) 10 MPa is the correct answer.
To know more about Mohr circle visit:
https://brainly.com/question/31642831
#SPJ11
The problem consists in determining the mechanical behaviour of a galvanized ordinary steel intended for the automobile body. For this, we have a rectangular test piece of this steel (length l0 = 50 mm, width b = 10 mm and thickness a = 1.5 mm). For an elongation of 0.001 mm, the load detected by the force sensors is 5450 N.
a. Calculate the initial cross section of the specimen.
b. Deduce the maximum tensile force if its ultimate tensile strength is UTS = 650 MPa
c. What should be the section at fracture Sf for a cylindrical test specimen, of the same material, with the same initial section as the rectangular test piece. Due to the necking coefficient, the reduction of its initial diameter is 10%
a.The initial cross-sectional area (A0) of the specimen is 500 mm²
b. The maximum tensile force is 3,25,000 N
c. The section at fracture Sf for a cylindrical test specimen is:6.43 mm²
a. Calculation of initial cross-section of the specimen:
Let’s calculate the initial cross-sectional area (A0) of the specimen by using the formula given below:
A0= l0 x bA0 = 50 mm x 10 mm= 500 mm²
b. Deduction of the maximum tensile force:
Let’s calculate the maximum tensile force using the formula given below:
F = σUTS x A0
F = 650 MPa x 500 mm²
F = 3,25,000 N
C. Calculation of the section at fracture Sf for a cylindrical test specimen:
Let’s calculate the section at fracture Sf using the formula given below:
Sf = (10% of initial diameter)² x π/4
Let’s find the initial diameter of the cylindrical test specimen by using the cross-sectional area formula:
A0 = π/4 × (initial diameter)²
500 mm² = 0.785 × (initial diameter)²
initial diameter = √(500 mm² ÷ 0.785)
initial diameter = 28.49 mm
Therefore, the 10% reduction of the initial diameter of the cylindrical test specimen is 2.85 mm.
Thus, the section at fracture Sf for a cylindrical test specimen is:
Sf = (2.85 mm)² x π/4Sf = 6.43 mm²
Learn more about tensile force at
https://brainly.com/question/13464062
#SPJ11
If a double-line-to-line fault occurs across "b" and "c" to ground, and Ea = 200 V20⁰, Zs = 0.06 2+j 0.15 , Zn = 0 and Z₁ = 0.05 2+j 0.2 02, find: a) the sequence current la1 then find lao and laz b) fault current If c) the sequence voltages Vai, Vaz and Vao d) sketch the sequence network for the line-to-line fault.
A line-to-line-to-ground fault is a type of fault in which a short circuit occurs between any two phases (line-to-line) as well as the earth or ground. As a result, the fault current increases, and the system's voltage decreases.
The line-to-line fault can be transformed into sequence network components, which will help to solve for fault current, voltage, and sequence current. For a three-phase system, the sequence network is shown below. Sequence network of a three-phase system. The fault current can be obtained by using the following formula; [tex]If =\frac{E_a}{Z_s + Z_1}[/tex][tex]Z_
s = 0.06 + j 0.15[/tex][tex]Z_1
= 0.05 + j 0.202[/tex][tex]If
=\frac{E_a}{Z_s + Z_1}[/tex][tex]
If =\frac{200}{0.06 + j 0.15+ 0.05 + j 0.202}[/tex][tex]
If =\frac{200}{0.11 + j 0.352}[/tex][tex
]If = 413.22∠72.5°[/tex]a)
Sequence current la1Sequence current formula is given below;[tex]I_{a1} = If[/tex][tex]I_{a1}
= 413.22∠72.5°[/tex] For la0, la0 is equal to (2/3) If, and la2 is equal to (1/3)
Sketch the sequence network for the line-to-line fault. The sequence network for the line-to-line fault is as shown below. Sequence network for line-to-line fault.
To know more about circuit visit:
https://brainly.com/question/12608516
#SPJ11
(a) A digger must be able to lift vertically loads up to 800 kg with a speed of 0.5 m/s. If the main hydraulic cylinder has a bore diameter of 5 cm, calculate the required oil flow rate, in m/s. (5 marks) (b) Calculate the required hydraulic pressure. (5 marks) (c) If the pump efficiency is 85%, calculate the hydraulic power and electrical power of the electric motor driving the pump. (5 marks) (d) If the digger is used to pull rather than lift, explain why it would not be able to develop the same equivalent load of 800 kg. (5 marks)
a) The formula to calculate the required oil flow rate isQ= A × VWhere Q is the flow rate, A is the cross-sectional area, and V is the velocity. In this problem, the bore diameter is given as 5 cm, which means that the radius, r = 2.5 cm = 0.025 m. Therefore, the cross-sectional area of the hydraulic cylinder is A = πr².Q = A × V= π × 0.025² × 0.5= 0.00098 m³/sb) The formula to calculate the required hydraulic pressure isP= F / Awhere P is the pressure, F is the force, and A is the area. In this problem, the maximum load that the digger can lift vertically is given as 800 kg, which means that the force, F = 800 × 9.81 = 7848 N. Therefore, the area, A = πr² = π × 0.025² = 0.00196 m².P = F / A= 7848 / 0.00196= 4 × 10⁶ Pa (4 MPa)c) The hydraulic power is given by the formulaP = Q × P = 0.00098 × 4 × 10⁶= 3920 WThe electrical power of the electric motor driving the pump is given by the formulaP = η × PeWhere η is the efficiency of the pump, and Pe is the electrical power input to the motor. In this problem, the efficiency of the pump is given as 85%. Therefore,P = 0.85 × Pe=> Pe = P / 0.85= 4600 W (approximately)d) If the digger is used to pull rather than lift, it would not be able to develop the same equivalent load of 800 kg because when the digger is lifting, it is working against gravity, which provides a constant opposing force. However, when the digger is pulling, the opposing force is friction, which is not a constant and can vary depending on the surface conditions. Therefore, the digger may not be able to develop the same equivalent load of 800 kg when pulling.
What will happen to the reactance of a capacitor when the frequency is reduced by 25 %? Select the correct response. O 33% more O 33% less O 25% less O 25% more
The correct response is 25% less Explanation: The reactance of a capacitor decreases as the frequency of the AC signal passing through it decreases.
When the frequency is reduced by 25%, the reactance of the capacitor will decrease by 25%.The reactance of a capacitor is given by the [tex]formula:Xc = 1 / (2 * pi * f * C)[/tex]whereXc is the reactance of the capacitor, pi is a mathematical constant equal to approximately 3.14, f is the frequency of the AC signal, and C is the capacitance of the capacitor.
From the above formula, we can see that the reactance is inversely proportional to the frequency. This means that as the frequency decreases, the reactance increases and vice versa.he reactance of the capacitor will decrease by 25%. This is because the reduced frequency results in a larger capacitive reactance value, making the overall reactance value smaller.
To know more about frequency visit:
https://brainly.com/question/29739263
#SPJ11
A building services engineer is designing an energy recovery system for a hospital at Kowloon Tong to recover the heat from the exhaust air to pre-heat the fresh air for energy saving. Suggest a suitable type of heat recovery system (runaround coil or thermal wheel) to be used for this hospital. Give justification on the selection.
A window type air-conditioning unit and an electric air heater are used for a jewellery shop at Wan Chai for year-round space air-conditioning purpose. Propose, with reasons, a suitable type of air-conditioning equipment to replace the existing installation in order to reduce the annual energy consumption.
1. Hospital in Kowloon Tong: A thermal wheel heat recovery system efficiently recovers both sensible and latent heat from the exhaust air to pre-heat fresh air, promoting energy savings and a healthier indoor environment in the hospital.
2. Jewellery Shop in Wan Chai: Replacing the existing setup, a Variable Refrigerant Flow (VRF) system offers energy efficiency, zoning flexibility, and the capability to provide heating and cooling, reducing annual energy consumption for year-round air conditioning in the jewellery shop.
1. Hospital in Kowloon Tong:
A thermal wheel heat recovery system would be suitable for the hospital to recover heat from the exhaust air and pre-heat the fresh air. A thermal wheel consists of a rotating heat exchanger with a wheel-like structure coated with a sorbent material. The wheel rotates between the exhaust and supply air streams, transferring both sensible and latent heat. This system is justified for the following reasons:
- Efficiency: Thermal wheels are highly efficient in transferring heat, making them suitable for applications where both sensible and latent heat recovery is desired. In a hospital setting, where the exhaust air may contain moisture and contaminants, the thermal wheel can effectively recover both heat and moisture.
- Energy Saving: By pre-heating the fresh air with the recovered heat, the thermal wheel reduces the load on the heating system, resulting in energy savings. It helps to maintain a comfortable and healthy indoor environment while minimizing the energy consumption for conditioning the fresh air.
2. Jewellery Shop in Wan Chai:
To reduce the annual energy consumption of the jewellery shop's air-conditioning system, a suitable replacement for the window type air-conditioning unit and electric air heater would be a Variable Refrigerant Flow (VRF) system. This choice is justified for the following reasons:
- Energy Efficiency: VRF systems use advanced inverter-driven compressors and variable-speed fans to adjust the cooling and heating capacity according to the actual demand. This ensures precise temperature control and minimizes energy wastage by avoiding frequent on/off cycles.
- Flexibility and Zoning: VRF systems allow for individual control of multiple indoor units, enabling zoning within the space. This feature is particularly beneficial for the jewellery shop, where different areas may have varying cooling or heating requirements. Zoning helps optimize energy usage by providing conditioned air only where needed.
- Heating and Cooling Capability: VRF systems provide both heating and cooling capabilities, eliminating the need for separate electric air heaters. By utilizing the heat pump function of the VRF system, the shop can efficiently heat the space during colder months without relying solely on electric resistance heating.
Overall, the VRF system offers improved energy efficiency, zoning flexibility, and the ability to provide both heating and cooling, making it a suitable choice to replace the existing air-conditioning setup in the jewellery shop, resulting in reduced annual energy consumption.
To learn more about latent heat Click Here: brainly.com/question/23976436
#SPJ11
5. A connecting rod of length I= 12 has a mass m₃= 0.02. Its mass moment of inertia is 0.62. Its CG is located 0.4/ from the crank pin, point A. A crank of length r = 3.5 has a mass m₂= 0.06. Its mass moment of inertia about its pivot is 0.3. Its CG is at 0.3r from the main pin, O₂. The piston mass=0.012. The linkage is running at a constant 2000rpm and crank position is 45°. a. Exactly balance the crank and recalculate the inertia force
b. Overbalance the crank with approximately two-thirds of the mass at the wrist pin placed at radius -r on the crank and recalculate the inertia force.
c. Compare these results to those for the unbalanced crank.
When exactly balancing the crank of a given linkage system, the inertia force is reduced to zero. However, when overbalancing the crank by placing approximately two-thirds of the mass at the wrist pin, the inertia force is increased. Comparing these results to the unbalanced crank shows the effect of balancing on the inertia force.
When exactly balancing the crank, the inertia force is eliminated. This means that there is no net force acting on the system due to the reciprocating masses. By carefully adjusting the mass distribution, the system can be made to run smoothly without experiencing any significant vibration or unbalanced forces. On the other hand, when overbalancing the crank by placing additional mass at the wrist pin, the inertia force is increased. The added mass at the wrist pin creates an imbalance, resulting in a net force acting on the system. This increased inertia force can lead to additional vibrations and unbalanced forces during the operation of the linkage system. Comparing these results to the unbalanced crank allows us to see the impact of balancing on the inertia force. Exactly balancing the crank eliminates the inertia force, resulting in a smoother operation. However, overbalancing the crank introduces an increased inertia force, which can negatively affect the performance and stability of the linkage system. Balancing techniques are crucial in minimizing vibrations and unbalanced forces, thereby optimizing the operation of mechanical systems.
Learn more about inertia force here:
https://brainly.com/question/30337839
#SPJ11
A single acting reciprocating pump has cylinder diameter of 200 mm and stroke length 300 m. The suction pipe is 100 mm diameter with 8 m long. The punp draws water 4 m below the cylinder axis. If the speed of the pump is 30 rpm. Find the pressure head on the piston at the beginning, middle and end of the suction stroke Notes: 1) The friction factor =0.01 and the atmospheric pressure head is 10.3 m of water. 2) The general pistion head equation is given by: Hpiston=Hatm+Zz-ha-hus
The pressure head on the piston at the beginning, middle, and end of the suction stroke is 438.5 m, 438.5 m, and 418.2 m, respectively.
Diameter of cylinder = 200 mm
Stroke length = 300 mm
Suction Pipe Diameter = 100 mm
Length of Suction Pipe = 8 m
Height from the cylinder axis to water level = 4 m
Speed of the pump = 30 rpm
Friction factor = 0.01
Atmospheric pressure head = 10.3 m of water
The general piston head equation is given by:
Hpiston = Hatm + Zz - ha - hus, where Hpiston = pressure head on the piston
Hatm = atmospheric pressure headZz = height of pump above sea level
ha = head loss in the suction pipeline
hus = suction lift
To calculate the pressure head on the piston at the beginning, middle, and end of the suction stroke, we will have to calculate different parameters using the given data as follows:
First, we will calculate the suction head as follows: suction head (Hus) = height from water level to center line of suction pipe+ friction loss in the suction pipe at suction lift= (4 + 1000*(0.01)*(8)/100)*1000/9.81= 41.5 m
Next, we will calculate the delivery head (Hd) as follows:
delivery head (Hd) = height from water level to the centerline of the cylinder - suction head (Hus)= (0 - 4)*1000/9.81= -407.7 m
We will now calculate the head loss due to the suction pipe using the Darcy Weisbach equation, which is given as follows:
H loss = (f x l x v²) / (2 x g x d)
where, f = friction factor
l = length of the pipe
v = velocity of flow in the piped = diameter of the pipe
g = acceleration due to gravity
Substituting the given values, we get:
H loss = (0.01 x 8 x (Q / A)²) / (2 x 9.81 x 0.1)= 0.000815 Q²
where, A is the cross-sectional area of the pipe, which is calculated as follows:
A = (π x d²) / 4= (π x 0.1²) / 4= 0.00785 m²We will now calculate the volumetric flow rate (Q) as follows:
Q = π x d² / 4 x v= π x 0.1² / 4 x (30 / 60) x (10⁻³)= 0.0002618 m³/s
Therefore, H loss = 0.000815 x (0.0002618)²= 0.000000005 m
We will now calculate the pressure head on the piston at the beginning, middle, and end of the suction stroke using the given formula Hpiston = Hatm + Zz - ha - hus as follows:
At the beginning of the suction stroke:
Hpiston (beginning) = 10.3 + 0 - (-407.7) - 41.5= 438.5 m
At the middle of the suction stroke:
Hpiston (middle) = 10.3 + 0 - (-407.7) - 20.75= 438.5 m
At the end of the suction stroke:Hpiston (end) = 10.3 + 0 - (-407.7) - 0= 418.2 m
Therefore, the pressure head on the piston at the beginning, middle, and end of the suction stroke is 438.5 m, 438.5 m, and 418.2 m, respectively.
To know more about suction visit:
https://brainly.com/question/28335109
#SPJ11
What are the criteria to say if the pump is a good choice?
It is essential to select the best value for money pump for the given application.
The criteria to determine whether a pump is a good choice are as follows:Performance criteria: The pump must be capable of meeting the performance criteria specified for the given application. Performance criteria may include, for example, flow rate, pressure, suction head, and temperature.
Manufacturers provide performance curves that show how these parameters are related to each other and how they vary with pump speed and impeller diameter.Reliability: The pump must be dependable and able to operate without interruption for long periods of time. To avoid unscheduled downtime and maintenance, it should be built to last and have a design that is resistant to wear and tear.
Maintenance: The pump must be easy to maintain, with replaceable parts that can be easily replaced on site, and with a service network that is easily accessible. Life cycle costs are often determined by maintenance costs, and the ease of maintenance may affect these costs.Materials of Construction: The materials of construction for a pump's wetted parts must be compatible with the liquid being pumped. Corrosion, erosion, and cavitation can cause significant damage to pumps and can be avoided by using appropriate materials of construction. Therefore, it is important to select the right materials of construction for the given application.
Cost: The pump must be cost-effective and be available at a reasonable price. Life cycle costs, including purchase price, installation, maintenance, and energy consumption, should be considered while determining the overall cost of the pump. Furthermore, there are different pumps available for different price points and applications. It is essential to select the best value for money pump for the given application.
Learn more about flow rate :
https://brainly.com/question/19863408
#SPJ11
In the following, there are two sets of G-codes where both of the cutters start at the origin of the workpiece coordinate system. Sketch two graphs for the tool paths and write down the coordinates of the end points for each code block.
(Set A) N10 G90 G17
N20 G00 X60 Y20 F950 S717 M03
N30 G01 X120 Y20 F350 M08
N40 G03 X120 Y60 10 J20
N50 G01 X120 Y20
N60 G01 X80 Y20
N70 G00 XO YO F950
N80 M02
(Set B) N10 G91 G17
N20 G00 X60 Y20 F950 S717 M03
N30 G01 X60 YO F350 M08
N40 G02 XO Y40 10 J20
N50 G01 X-40 YO
N60 G01 XO Y-40
N70 G00 X-80 Y-20 F950
N80 M02
Main Answer:
The tool path for Set A starts at the origin, moves to (60, 20), then follows a curved path to (120, 60), and finally returns to (120, 20). The tool path for Set B also starts at the origin, moves to (60, 20), then follows a circular path to (-40, 0), and returns to (-80, -20).
Explanation:
In Set A, the G-code commands specify that the tool should move in absolute coordinates (G90) and use the XY plane (G17). After setting these parameters, the tool rapidly moves to (60, 20) with a high feedrate (F950) and starts rotating clockwise at a speed of 717 RPM (S717) (M03). It then moves in a straight line to (120, 20) at a slower feedrate (F350) while turning the spindle on (M08). From there, it follows a clockwise circular path with a radius of 10 units and a center at (120, 60) (G03 X120 Y60 10 J20). After completing the circular path, it moves back to (120, 20) (G01 X120 Y20), then to (80, 20) (G01 X80 Y20). Finally, it rapidly moves back to the origin (G00 XO YO F950) and stops the spindle (M02).
In Set B, the G-code commands specify incremental coordinates (G91) and the XY plane (G17). The tool starts by moving rapidly to (60, 20) (G00 X60 Y20 F950) and turning the spindle on (M03). It then moves in a straight line to (60, 0) (G01 X60 YO), where the Y-coordinate remains the same. After that, it follows a counterclockwise circular path with a radius of 10 units and a center at (0, 40) (G02 XO Y40 10 J20). It then moves back to the origin (G01 X-40 YO) and finally to (-80, -20) (G00 X-80 Y-20 F950). The spindle is stopped (M02) to complete the tool path.
Learn more about G-code programming and CNC tool paths to gain a deeper understanding of how these codes control the movement of machine tools in manufacturing processes. #SPJ11
Set A: The tool path starts at the origin and moves to (60, 20) in a rapid traverse, then follows a linear path to (120, 20) before executing a clockwise arc to (120, 60). It then moves linearly to (120, 20) and (80, 20) before returning to the origin.
Set B: The tool path starts at the origin and moves to (60, 20) in a rapid traverse, then follows a linear path to (60, 0) before executing a clockwise arc to (0, 40). It then moves linearly to the origin and (-40, 0) before returning to (-80, -20).
Set A: The tool path in Set A starts at the origin and moves to (60, 20) in a rapid traverse. Then, it follows a linear path to (120, 20) at a feed rate of 350 units per minute. Next, it executes a clockwise arc from (120, 20) to (120, 60) with a radius of 10 units and a center at (120, 40). After that, it moves linearly to (120, 20) and then to (80, 20). Finally, it returns to the origin in a rapid traverse.
Set B: The tool path in Set B also starts at the origin and moves to (60, 20) in a rapid traverse. Then, it follows a linear path to (60, 0) at a feed rate of 350 units per minute. Next, it executes a clockwise arc from (60, 0) to (0, 40) with a radius of 10 units and a center at (20, 20). After that, it moves linearly to the origin and then to (-40, 0). Finally, it returns to (-80, -20) in a rapid traverse.
In Set A, the end points of the tool path are: (60, 20), (120, 20), (120, 60), (120, 20), and (80, 20). In Set B, the end points of the tool path are: (60, 20), (60, 0), (0, 40), (0, 0), (-40, 0), and (-80, -20).
Learn more about tool paths visit
brainly.com/question/30839962
#SPJ11
(a) Articulate the principles of solid-waste separation.
(b) Traditional anaerobic landfills pose many major environmental and health concerns because they produce toxic leachate and contain high concentrations of organic compounds and pathogens. Semi-aerobic landfills are designed to overcome the challenges associated with the traditional anaerobic landfills, briefly discuss the concept of semi-aerobic landfills.
Semi-aerobic landfills combine anaerobic and aerobic processes to enhance waste decomposition, minimize leachate production, and reduce environmental and health concerns associated with traditional anaerobic landfills.
(a) The principles of solid-waste separation involve the systematic sorting and segregation of different types of waste materials to facilitate proper disposal, recycling, and resource recovery. The key principles are:
1. Source Separation: Waste should be separated at its point of origin into categories such as recyclables, organic waste, and non-recyclables.
2. Segregation: Different waste streams should be kept separate to prevent contamination and optimize recycling potential.
3. Recyclability: Materials that can be recycled should be identified and separated for further processing and recycling.
4. Hazardous Waste Management: Hazardous materials should be separated and disposed of separately to prevent harm to the environment and human health.
5. Education and Awareness: Public education programs are essential to promote waste separation and recycling practices among individuals and communities.
(b) Semi-aerobic landfills are designed to address the issues associated with traditional anaerobic landfills. They employ a combination of aerobic and anaerobic processes to enhance waste degradation and minimize environmental and health risks. In a semi-aerobic landfill, waste is compacted and covered with layers of soil or other materials to reduce oxygen availability, promoting anaerobic decomposition. However, the landfill is periodically aerated by introducing air or oxygen to facilitate aerobic breakdown of organic matter.
This semi-aerobic environment promotes the growth of aerobic microorganisms, which accelerate waste decomposition and reduce the production of toxic leachate. The controlled aeration also helps to mitigate odor generation and reduce the release of greenhouse gases. Overall, semi-aerobic landfills aim to provide better waste degradation, lower environmental impact, and improved management of organic compounds and pathogens.
LEARN MORE ABOUT landfills here: brainly.com/question/31565051
#SPJ11
1 kmol/s of methane (CH4, MW = 16 kg/kmol) is burned in 20% excess air (fuel and air starting at 25°C), allowing for complete combustion and conversion of all of the methane. The water produced is in the vapor state. a) In the space below, write the balanced reaction for this system, including all species present. b) How much heat is released by this combustion reaction, in kJ per kmol of methane burned? c) If the reactor is adiabatic, what is the exiting temperature (K) of the product gas mixture? You may assume cp = 4Ru for all gases.
The heat released by the combustion of 1 kmol of methane is approximately -802.2 kJ, and the exiting temperature of the product gas mixture, in an adiabatic reactor, is approximately 0.69°C.
a) The balanced reaction for the combustion of methane with excess air is:
CH4 + 2(O2 + 3.76N2) -> CO2 + 2H2O + 7.52N2
b) To calculate the heat released by the combustion reaction, we can use the heat of formation values for each compound involved. The heat released can be calculated as follows:
Heat released = (ΣΔHf(products)) - (ΣΔHf(reactants))
ΔHf refers to the heat of formation.
Given the heat of formation values:
ΔHf(CH4) = -74.9 kJ/mol
ΔHf(CO2) = -393.5 kJ/mol
ΔHf(H2O) = -241.8 kJ/mol
ΔHf(N2) = 0 kJ/mol
ΔHf(O2) = 0 kJ/mol
Calculating the heat released:
Heat released = [1 * ΔHf(CO2) + 2 * ΔHf(H2O) + 7.52 * ΔHf(N2)] - [1 * ΔHf(CH4) + 2 * (0.2 * ΔHf(O2) + 0.2 * 3.76 * ΔHf(N2))]
Heat released = [1 * -393.5 kJ/mol + 2 * -241.8 kJ/mol + 7.52 * 0 kJ/mol] - [1 * -74.9 kJ/mol + 2 * (0.2 * 0 kJ/mol + 0.2 * 3.76 * 0 kJ/mol)]
Heat released ≈ -802.2 kJ/mol
Therefore, the heat released by the combustion reaction is approximately -802.2 kJ per kmol of methane burned.
c) Since the reactor is adiabatic, there is no heat exchange with the surroundings. Therefore, the heat released by the combustion reaction is equal to the change in enthalpy of the product gas mixture.
Using the equation:
ΔH = Cp * ΔT
where ΔH is the change in enthalpy, Cp is the heat capacity at constant pressure, and ΔT is the change in temperature, we can rearrange the equation to solve for ΔT:
ΔT = ΔH / Cp
Given that Cp = 4Ru for all gases, where Ru is the gas constant (8.314 J/(mol·K)), we can substitute the values:
ΔT = (-802.2 kJ/mol) / (4 * 8.314 J/(mol·K))
ΔT ≈ -24.31 K
The exiting temperature of the product gas mixture is the initial temperature (25°C) minus the change in temperature:
Exiting temperature = 25°C - 24.31 K
Exiting temperature ≈ 0.69°C (rounded to two decimal places)
Therefore, if the reactor is adiabatic, the exiting temperature of the product gas mixture is approximately 0.69°C.
Learn more about combustion
brainly.com/question/31123826
#SPJ11
As the viscosity of fluids increases the boundary layer
thickness does what? Remains the same? Increases? Decreases?
Explain your reasoning and show any relevant mathematical
expressions.
As the viscosity of fluids increases, the boundary layer thickness increases. This can be explained by the fundamental principles of fluid dynamics, particularly the concept of boundary layer formation.
In fluid flow over a solid surface, a boundary layer is formed due to the presence of viscosity. The boundary layer is a thin region near the surface where the velocity of the fluid is influenced by the shear forces between adjacent layers of fluid. The thickness of the boundary layer is a measure of the extent of this influence.
Mathematically, the boundary layer thickness (δ) can be approximated using the Blasius solution for laminar boundary layers as:
δ ≈ 5.0 * (ν * x / U)^(1/2)
where:
δ = boundary layer thickness
ν = kinematic viscosity of the fluid
x = distance from the leading edge of the surface
U = free stream velocity
From the equation, it is evident that the boundary layer thickness (δ) is directly proportional to the square root of the kinematic viscosity (ν) of the fluid. As the viscosity increases, the boundary layer thickness also increases.
This behavior can be understood by considering that a higher viscosity fluid resists the shearing motion between adjacent layers of fluid more strongly, leading to a thicker boundary layer. The increased viscosity results in slower velocity gradients and a slower transition from the no-slip condition at the surface to the free stream velocity.
Therefore, as the viscosity of fluids increases, the boundary layer thickness increases.
To know more about viscosity, click here:
https://brainly.com/question/30640823
#SPJ11
please solve in 45'minutes , i will give you three likes
A plate (length l, height h, thickness d (z-coordinate) is in a frame without friction and stress.
Neglect the weight of the plate.
Given: l, h, d, q0, E, v=0.3 (Poisson's ratio)
Calculate the change in thickness delta d in m^-6.
Calculate the change in height delta h in m^-6.
Calculate the Normal stress in x and y.
The change in thickness is delta[tex]d ≈ 1.54 · 10^(-6) m^-6.[/tex]
The change in height is delta h = 0.Given:Length of the plate: l
Height of the plate: h
Thickness of the plate: d
Poisson's ratio: v = 0.3
Young's modulus: E
Stress:[tex]σ_xy[/tex]
Normal stress: [tex]σ_x, σ_y[/tex]
Shear stress:[tex]τ_xy[/tex]
Solution:
Area of the plate = A = l · h
Thickness of the plate: d
Shear strain:[tex]γ_xy = q_0 / G[/tex], where G is the shear modulus.
We can find G as follows:
G = E / 2(1 + v)
= E / (1 + v)
= 2E / (2 + 2v)
Shear modulus:
G= E / (1 + v)
= 2E / (2 + 2v)
Shear stress:
[tex]τ_xy= G · γ_xy[/tex]
[tex]= (2E / (2 + 2v)) · (q_0 / G)[/tex]
[tex]= q_0 · (2E / (2 + 2v)) / G[/tex]
[tex]= q_0 · (2 / (1 + v))[/tex]
[tex]= q_0 · (2 / 1.3)[/tex]
[tex]= 1.54 · q_0[/tex]
[tex]Stress:σ_xy[/tex]
[tex]= -v / (1 - v^2) · (σ_x + σ_y)δ_h[/tex]
[tex]= 0δ_d[/tex]
[tex]= τ_xy / (A · E)[/tex]
[tex]= (1.54 · q_0) / (l · h · E)σ_x[/tex]
[tex]= σ_y[/tex]
[tex]= σ_0[/tex]
[tex]= q_0 / 2[/tex]
Normal stress:
[tex]σ_x = -v / (1 - v^2) · (σ_y - σ_0)σ_y[/tex]
[tex]= -v / (1 - v^2) · (σ_x - σ_0)[/tex]
Change in thickness:
[tex]δ_d= τ_xy / (A · E)[/tex]
[tex]= (1.54 · q_0) / (l · h · E)[/tex]
[tex]= (1.54 · 9.8 · 10^6) / (2.6 · 10^(-4) · 2.2 · 10^(-4) · 206 · 10^9)[/tex]
[tex]≈ 1.54 · 10^(-6) m^-6[/tex]
Change in height:δ[tex]_h[/tex]= 0
Normal stress:
[tex]σ_x= σ_y= σ_0 = q_0 / 2 = 4.9 · 10^6 Pa[/tex]
Answer: The change in thickness is delta
d ≈ [tex]1.54 · 10^(-6) m^-6.[/tex]
The change in height is delta h = 0
To know more about stress visit:
https://brainly.com/question/31366817
#SPJ11
What is an Optiz classification system? In a couple of sentences or bullet points explain what it is and how it is used to classify parts For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac) BIUS Paragraph V Arial 10pt 111 A V V I %6
The Otiz classification system is used to classify the parts in a computer system. The computer system consists of many different parts, each of which performs a specific function.
To organize and classify these parts, the Otiz classification system was developed. The system is used to classify the parts based on their function, type, and location. It is a hierarchical system that divides the computer system into several levels, each of which is further subdivided into smaller parts. The system is used to simplify the process of organizing and categorizing parts in a computer system, making it easier to understand and work with. In summary, the Otiz classification system is a system used to classify the parts of a computer system based on their function, type, and location, and it is used to simplify the process of organizing and categorizing parts.
To know more about classification visit:
brainly.com/question/645379
#SPJ11
3. (a) Find the partial differential equation by eliminating the arbitrary function from z = xfi(x + bt) + f2(x + bt). (b) Form the partial differential equation by eliminating the arbitrary constants a and b from z = z = blog[ey1), 1-X
The purpose of eliminating arbitrary functions is to obtain a simplified form of the equation that relates the variables involved, allowing for easier analysis and solution of the partial differential equation.
What is the purpose of eliminating arbitrary functions and constants in partial differential equations?In the given problem, we are asked to eliminate the arbitrary function and arbitrary constants from two different equations.
(a) To eliminate the arbitrary function from the equation z = xfi(x + bt) + f2(x + bt), we need to differentiate the equation with respect to x and t separately. By eliminating the derivatives of the arbitrary function, we can obtain the partial differential equation.
(b) To eliminate the arbitrary constants a and b from the equation z = blog[ey1), 1-X, we need to differentiate the equation with respect to x and y separately. By equating the derivatives and solving the resulting equations, we can eliminate the arbitrary constants and obtain the partial differential equation.
Overall, the goal of these problems is to manipulate the given equations in order to remove any arbitrary functions or constants, and obtain a partial differential equation that relates the variables involved.
Learn more about eliminating arbitrary functions
brainly.com/question/31772977
#SPJ11
List out the methods to improve the efficiency of the Rankine cycle
The Rankine cycle is an ideal cycle that includes a heat engine which is used to convert heat into work. This cycle is used to drive a steam turbine.
The efficiency of the Rankine cycle is affected by a variety of factors, including the quality of the boiler, the temperature of the working fluid, and the efficiency of the turbine. Here are some methods that can be used to improve the efficiency of the Rankine cycle:
1. Superheating the Steam: Superheating the steam increases the temperature and pressure of the steam that is leaving the boiler, which increases the work done by the turbine. This results in an increase in the overall efficiency of the Rankine cycle.2. Regenerative Feed Heating: Regenerative feed heating involves heating the feed water before it enters the boiler using the waste heat from the turbine exhaust. This reduces the amount of heat that is lost from the cycle and increases its overall efficiency.
To know more about work visit:
brainly.com/question/31349436
#SPJ11
What is specific enthalpy of vaporization of liquid-vapor mixture at 6 bar? At 6 bar, hg = 2756.8 kJ/kg, hf = 670.56 kJ/kg
The specific enthalpy of vaporization of the liquid-vapor mixture at 6 bar is approximately 2086.24 kJ/kg.
What is the specific enthalpy of vaporization of the liquid-vapor mixture at 6 bar?The specific enthalpy of vaporization (Δh) of a liquid-vapor mixture at 6 bar can be calculated by subtracting the specific enthalpy of the liquid phase (hf) from the specific enthalpy of the vapor phase (hg).
Given:
hg = 2756.8 kJ/kg
hf = 670.56 kJ/kg
Δh = hg - hf
Δh = 2756.8 kJ/kg - 670.56 kJ/kg
Δh ≈ 2086.24 kJ/kg
Therefore, the specific enthalpy of vaporization of the liquid-vapor mixture at 6 bar is approximately 2086.24 kJ/kg.
Learn more about vapor mixture
brainly.com/question/30652627
#SPJ11
The mechanical ventilation system of a workshop may cause a nuisance to nearby
residents. The fan adopted in the ventilation system is the lowest sound power output
available from the market. Suggest a noise treatment method to minimize the nuisance
and state the considerations in your selection.
The noise treatment method to minimize the nuisance in the ventilation system is to install an Acoustic Lagging. The Acoustic Lagging is an effective solution for the problem of sound pollution in mechanical installations.
The best noise treatment method for the workshop mechanical ventilation system. The selection of a noise treatment method requires a few considerations such as the reduction of noise to a safe level, whether the method is affordable, the effectiveness of the method and, if it is suitable for the specific environment.
The following are the considerations in the selection of noise treatment methods, Effectiveness, Ensure that the chosen method reduces noise levels to more than 100 DB without fail and effectively, especially in environments with significant noise levels.
To know more about treatment visit:
https://brainly.com/question/31799002
#SPJ11
The chemical reaction of the fuel with air gives rise to different compounds according to with the amount of air used. Determine the coefficients of the reactants and products of combustion*, as well as the fuel-air reaction for 100% and 130% air.
Fuel is C15H4
The given fuel is C15H4. The combustion reaction of a hydrocarbon fuel can be represented as:[tex]`CxHy + (x + y/4)O2 → xCO2 + y/2 H2O`[/tex]Where x and y are the coefficients of the fuel hydrocarbon's carbon and hydrogen atoms, respectively.
We first need to find the stoichiometric air-fuel ratio, which is the amount of air needed for complete combustion of the fuel with no excess oxygen left over. It is calculated by dividing the amount of air required to supply just enough oxygen to the fuel by the amount of air actually supplied.
The stoichiometric air-fuel ratio is given by the following equation:`AFR = (mass of air/mass of fuel) = (mass of oxygen/mass of fuel)/(mass of oxygen/mass of air)`The mass of air required to completely burn one unit of fuel is given by the following equation the stoichiometric air-fuel ratio can be calculated.
To know more about combustion visit:
https://brainly.com/question/31123826
#SPJ11
Identify the incorrect code by line number only. Do not rewrite the code (i.e. if line 3 was incorrect the answer would be: 3). There is only one error. I/ This code snippet is from a program that implements a 4×3 key scanned I/ keypad interface. A periodic timer interrupt is used to poll the keypad. 1.static inline void DRIVE_ROW_HIGH()\{ 2. RO=1; 3. R1=1; 4. R2=0 : 5.)
The incorrect line in the code snippet is line 4, where a colon (:) is used instead of a semicolon (;) to terminate the statement.
The code snippet implements a keypad interface using a periodic timer interrupt. The interrupt is a mechanism that suspends the normal program flow at regular intervals to poll the keypad for input.
By utilizing a timer interrupt, the program can periodically check the state of the keypad and handle key presses accordingly.
This approach allows for efficient and responsive keypad scanning, ensuring that user input is detected promptly. The interrupt-driven design improves the overall user experience by enabling real-time interaction with the keypad interface.
Learn more about code snippet here:
https://brainly.com/question/30471072
#SPJ4
Question 1. Write the full set of Maxwell's equations in differential form with a brief explanation for the case of: (iii) a steady current flow in a homogeneous conductor of conductivity o, with no impressed electric field;
Maxwell's equations are as follows:
[tex]$$∇⋅D=ρ$$[/tex]
Here, D is the electric flux density, and ρ is the electric charge density.
[tex]$$∇⋅B=0$$[/tex]
Here, B is the magnetic field.[tex]$$∇×E=-∂B/∂t$$[/tex]
Here, E is the electric field and ∂B/∂t is the rate of change of the magnetic field with respect to time.
[tex]$$∇×H=J$$[/tex]
Here, H is the magnetic field intensity, and J is the electric current density. When the electric current is steady, it does not change with time, and hence, ∂B/∂t = 0. Hence, the fourth Maxwell equation for the case of steady current flow in a homogeneous conductor of conductivity o, with no impressed electric field is:
[tex]$$∇×H=J$$[/tex]
Where H is the magnetic field intensity and J is the electric current density. The conductivity of the conductor is given by o.The steady flow of electric current produces a magnetic field around the conductor. The magnetic field produced is proportional to the current and is given by the Biot-Savart law.
To know more about keyword visit:
https://brainly.com/question/30764718
#SPJ11
Design a domestic no - frost freezer with the following design requirements. Cooling capacity 300 W at -18 deg C. • Volume of Freezer: 300 L Single Door Operating temperature outside : 32 deg C Refrigerant type : R -134a
To design a domestic no-frost freezer with the given requirements, including a cooling capacity of 300 W at -18°C, a volume of 300 L, an operating temperature outside of 32°C, and the use of R-134a as the refrigerant.
To design a domestic no-frost freezer, several considerations need to be taken into account. The cooling capacity of 300 W at -18°C ensures that the freezer can maintain the desired temperature inside. The volume of 300 L provides sufficient space for storing frozen goods. To achieve efficient cooling, the freezer should be equipped with appropriate insulation to minimize heat transfer from the outside. The selection of R-134a as the refrigerant ensures effective heat transfer and cooling performance. The freezer should have a single door with a proper sealing mechanism to prevent air leakage and maintain temperature stability.
Learn more about domestic no-frost freezer here:
https://brainly.com/question/31936174
#SPJ11
7. A gas turbine operates with the following parameters:
i) Atmospheric pressure 1.02 bar
ii) Atmospheric temperature 19°C
iii) Compressor output 7.2 bar
iv) Compressor isentropic efficiency 87%
v) Maximum temperature 1250°C
vi) Air expands in two stages in series back to atmospheric pressure
vii) External load 105 kW
viii) Isentropic efficiency for both stages is 91%
(X) Yca = 1.4 x) Ycu = 1.333
xi) R=0.287 kJ/kg K
Calculate the following:
a) Temperature (actual) T₂
b) Temperature (ideal) T4
c) Inter-stage pressure of the turbines.
d) Temperature (actual) T5 e) Mass flow of air. f) Heat input to combustion chamber.
g) Thermal efficiency.
Atmospheric pressure = 1.02 bar Atmospheric temperature = 19°C Compressor output = 7.2 bar Compressor isentropic efficiency = 87%Maximum temperature = 1250°C
Temperature (actual) T₂ Given that, atmospheric pressure, p1 = 1.02 bar Compressor output, p2 = 7.2 barIsen tropic efficiency of compressor, ηc = 87%Using the formula for isentropic compression,T2s / T1 = (p2 / p1)^(γ - 1)T2s = T1 (p2 / p1)^(γ - 1)T2s = 292.15 K (7.2 / 1.02)^(1.4 - 1)T2s = 659.2 K Using the actual efficiency,T2a / T1 = (p2 / p1)^((γ - 1) / ηc)T2a = T1 (p2 / p1)^((γ - 1) / ηc)T2a = 292.15 K (7.2 / 1.02)^((1.4 - 1) / 0.87)T2a = 602.2 K Therefore, temperature (actual), T₂ = T2a = 602.2 K b) Temperature (ideal) T4Given that maximum temperature, T3 = 1250 K Isentropic efficiency for both stages, ηT = 91%Using the formula for isentropic expansion,T4s / T3 = (p4 / p3)^((γ - 1) / γ)T4s = T3 (p4 / p3)^((γ - 1) / γ)T4s = 1250 (1 / 7.2)^((1.4 - 1) / 1.4)T4s = 585.8 K
To know more about Compressor visit:-
https://brainly.com/question/32087758
#SPJ11