When the source is moving away from the observer the velocity of the source is added to the speed of light. This increases the value of the denominator, decreasing the value of the observed frequency. Frequency corresponds to pitch or tone; a lower observed frequency will result in a lower observed pitch.
1.An elevator is ascending with constant speed of 10 m/s. A boy in the elevator throws a ball upward at 20 m/ a from a height of 2 m above the elevator floor when the elevator floor when the elevator is 28 m above the ground.
a. What's the maximum height?
b. How long does it take for the ball to return to the elevator floor?
(a) The maximum height reached by the ball from the ground level is 75.87m
(b) The time taken for the ball to return to the elevator floor is 2.21 s
The given parameters include:
constant velocity of the elevator, u₁ = 10 m/sinitial velocity of the ball, u₂ = 20 m/sheight of the boy above the elevator floor, h₁ = 2 mheight of the elevator above the ground, h₂ = 28 mTo calculate:
(a) the maximum height of the projectile
total initial velocity of the projectile = 10 m/s + 20 m/s = 30 m/s (since the elevator is ascending at a constant speed)
at maximum height the final velocity of the projectile (ball), v = 0
Apply the following kinematic equation to determine the maximum height of the projectile.
[tex]v^2 = u^2 + 2(-g)h_3\\\\where;\\\\g \ is \ the \ acceleration \ due \ to\ gravity = 9.81 \ m/s^2\\\\h_3 \ is \ maximum \ height \ reached \ by \ the \ ball \ from \ the \ point \ of \ projection\\\\0 = u^2 -2gh_3\\\\2gh_3 = u^2 \\\\h_3 = \frac{u^2}{2g} \\\\h_3 = \frac{(30)^2}{2\times 9.81} \\\\h_3 = 45.87 \ m[/tex]
The maximum height reached by the ball from the ground level (h) = height of the elevator from the ground level + height of he boy above the elevator + maximum height reached by elevator from the point of projection
h = h₁ + h₂ + h₃
h = 28 m + 2 m + 45.87 m
h = 75.87 m
(b) The time taken for the ball to return to the elevator floor
Final height of the ball above the elevator floor = 2 m + 45.87 m = 47.87 m
Apply the following kinematic equation to determine the time to return to the elevator floor.
[tex]h = vt + \frac{1}{2} gt^2\\\\where;\\\\v \ is \ the \ initial \ velocity \ of \ the \ ball \ at \ the \ maximum \ height = 0\\\\h = \frac{1}{2} gt^2\\\\gt^2 = 2h\\\\t^2 = \frac{2h}{g} \\\\t = \sqrt{\frac{2h}{g}} \\\\t = \sqrt{\frac{2\times 47.87}{9.81}} \\\\t = 2.21 \ s[/tex]
To learn more about projectile calculations please visit: https://brainly.com/question/14083704
To get an idea of the order of magnitude of inductance, calculate the self-inductance in henries for a solenoid with 1500 loops of wire wound on a rod 13 cm long with radius 2 cm
Answer:
The self-inductance in henries for the solenoid is 0.0274 H.
Explanation:
Given;
number of turns, N = 1500 turns
length of the solenoid, L = 13 cm = 0.13 m
radius of the wire, r = 2 cm = 0.02 m
The self-inductance in henries for a solenoid is given by;
[tex]L = \frac{\mu_oN^2A}{l}[/tex]
where;
[tex]\mu_o[/tex] is permeability of free space = [tex]4\pi*10^{-7} \ H/m[/tex]
A is the area of the solenoid = πr² = π(0.02)² = 0.00126 m²
[tex]L = \frac{4\pi *10^{-7}(1500)^2*(0.00126)}{0.13} \\\\L = 0.0274 \ H[/tex]
Therefore, the self-inductance in henries for the solenoid is 0.0274 H.
How wide is the central diffraction peak on a screen 2.20 mm behind a 0.0328-mmmm-wide slit illuminated by 588-nmnm light?
Answer:
[tex]y = 0.0394 \ m[/tex]
Explanation:
From the question we are told that
The distance of the screen is [tex]D = 2.20 \ m[/tex]
The distance of separation of the slit is [tex]d = 0.0328 \ mm = 0.0328*10^{-3} \ m[/tex]
The wavelength of light is [tex]\lambda = 588 \ nm = 588 *10^{-9} \ m[/tex]
Generally the condition for constructive interference is
[tex]dsin\theta = n * \lambda[/tex]
=> [tex]\theta = sin^{-1} [ \frac{ n * \lambda }{d } ][/tex]
here n = 1 because we are considering the central diffraction peak
=> [tex]\theta = sin^{-1} [ \frac{ 1 * 588*10^{-9} }{0.0328*10^{-3} } ][/tex]
=> [tex]\theta = 1.0274 ^o[/tex]
Generally the width of central diffraction peak on a screen is mathematically evaluated as
[tex]y = D tan (\theta )[/tex]
substituting values
[tex]y = 2.20 * tan (1.0274)[/tex]
[tex]y = 0.0394 \ m[/tex]
What is the need for satellite communication elaborate
The high frequency radio waves used for telecommunications links travel by line of sight and so are obstructed by the curve of the Earth. The purpose of communications satellites is to relay the signal around the curve of the Earth allowing communication between widely separated geographical points.
Explanation:
hope it helps!!
why is nut-cracker 2nd class lever?
2nd class leaver refers to such leaver in which load lies between effort and fulcrum.In a nut cracker too load is in between effort and fulcrum.Thus, nut cracker is a 2nd class leaver.......
In the direction perpendicular to the drift velocity, there is a magnetic force on the electrons that must be cancelled out by an electric force. What is the magnitude of the electric field that produces this force
Answer:
E = VdB
Explanation:
This is because canceling the electric and magnetic force means
q.vd. B= we
E= Vd. B
Please help wil give brainiest & 40p.
Answer:
This is the answer
Explanation:
You can find the ans in the photo I attached.
In Young's experiment a mixture of orange light (611 nm) and blue light (471 nm) shines on the double slit. The centers of the first-order bright blue fringes lie at the outer edges of a screen that is located 0.497 m away from the slits. However, the first-order bright orange fringes fall off the screen. By how much and in what direction (toward or away from the slits) should the screen be moved, so that the centers of the first-order bright orange fringes just appear on the screen
Answer:
0.5639m
Explanation:
For a young double slit experiment the expression below gives the angular separation for m dark fringe having slit width d and wavelength λ
=sin⁻¹(mλ/d)
mλ /d =y/L
for the first order,
y= mλL/d
For ratio separation y₀/yD=1 and d= 1
y₀/yD= [mλ ₀L₀/d]/[mλD.LD./d]
1=λ ₀L₀/λD.LD.
λD.LD= λ ₀L₀
L₀= λD.LD/ λ ₀..............(1)
Then substitute the given values into (1) we have
L₀=471 *0.497/611
= 0.3831m
Distance by which the screen has to be moved towards the slit is
LD- Lo
0.947-0.3831= 0.5639m
2. The vector sums of and the Ark witar must se rue our the directions and maintedes at an Bit CB? What meast le tue about the directions and magnitudes and it cor
Check attached photo
Check attached photo
The physics of wind instruments is based on the concept of standing waves. When the player blows into the mouthpiece, the column of air inside the instrument vibrates, and standing waves are produced. Although the acoustics of wind instruments is complicated, a simple description in terms of open and closed tubes can help in understanding the physical phenomena related to these instruments. For example, a flute can be described as an open-open pipe because a flutist covers the mouthpiece of the flute only partially. Meanwhile, a clarinet can be described as an open-closed pipe because the mouthpiece of the clarinet is almost completely closed by the reed.
1. Consider a pipe of length 80.0 cm open at both ends. What is the lowest frequency f of the sound wave produced when you blow into the pipe?
2. A hole is now drilled through the side of the pipe and air is blown again into the pipe through the same opening. The fundamental frequency of the sound wave generated in the pipe is now:______.
a. the same as before.
b. lower than before.
c. higher than before.
3. If you take the original pipe in Part A and drill a hole at a position half the length of the pipe, what is the fundamental frequency of the sound that can be produced in the pipe?
4. What frequencies, in terms of the fundamental frequency of the original pipe in Part A, can you create when blowing air into the pipe that has a hole halfway down its length?
4-1. Recall from the discussion in Part B that the standing wave produced in the pipe must have an antinode near the hole. Thus only the harmonics that have an antinode halfway down the pipe will still be present.
A. Only the odd multiples of the fundamental frequency.
B. Only the even multiples of the fundamental frequency.
C. All integer multiples of the fundamental frequency.
E. What length of open-closed pipe would you need to achieve the same fundamental frequency as the open pipe discussed in Part A?
A. Half the length of the open-open pipe.
B. Twice the length of the open-open pipe.
C. One-fourth the length of the open-open pipe.
D. Four times the length of the open-open pipe.
E. The same as the length of the open-open pipe.
F. What is the frequency of the first possible harmonic after the fundamental frequency in the open-closed pipe described in Part E?
F-1. Recall that possible frequencies of standing waves that can be generated in an open-closed pipe include only odd harmonics. Then the first possible harmonic after the fundamental frequency is the third
harmonic.
Answer:
1) f = 214 Hz , 2) answer is c , 3) f = 428 Hz , 4) f₂ = 428 Hz , f₃ = 643Hz
Explanation:
1) A tube with both ends open, the standing wave has a maximum amplitude and a node in its center, therefore
L = λ / 2
λ = 2L
λ = 2 0.8
λ = 1.6 m
wavelength and frequency are related to the speed of sound (v = 343 m / s)
v =λ f
f = v / λ
f = 343 / 1.6
f = 214 Hz
2) In this case the air comes out through the open hole, so we can assume that the length of the tube is reduced
λ' = 2 L ’
as L ’<L₀
λ' <λ₀
f = v / λ'
f' > fo
the correct answer is c
3) in this case the length is L = 0.40 m
λ = 2 0.4 = 0.8 m
f = 343 / 0.8
f = 428 Hz
4) the different harmonics are described by the expression
λ = 2L / n n = 1, 2, 3
λ₂ = L
f₂ = 343 / 0.8
f₂ = 428 Hz
λ₃ = 2 0.8 / 3
λ₃ = 0.533 m
f₃ = 343 / 0.533
f₃ = 643 Hz
4,1) as we have two maximums at the ends, all integer multiples are present
the answer is C
E) the length of an open pipe created that has a wavelength of lam = 1.6 m is requested
in this pipe there is a maximum in the open part and a node in the closed part, so the expression
L = λ / 4
L = 1.6 / 4
L = 0.4 m
the answer is C
F) in this type of pipe the general expression is
λ = 4L / n n = 1, 3, 5 (2n + 1)
therefore only odd values can produce standing waves
λ₃ = 4L / 3
λ₃ = 4 0.4 / 3
λ₃ = 0.533
f₃ = 343 / 0.533
f₃ = 643 Hz
A goldfish bowl is spherical, 8.0 cm in radius. A goldfish is swimming 3.0 cm from the wall of the bowl. Where does the fish appear to be to an observer outside? The index of refraction of water is 1.33. Neglect the effect of the glass wall of the bowl.
Answer:
41.5 cm to the left of the observer
Explanation:
See attached file
By what factor is the intensity of sound at a rock concert louder than that of a whisper when the two intensity levels are 120 dB and 20 dB respectively
Answer:
The intensity of sound at rock concert is 10¹⁰ greater than that of a whisper.
Explanation:
The intensity of sound is given by;
[tex]I(dB) = 10Log(\frac{I}{I_o} )[/tex]
where;
I is the intensity of the sound
I₀ is the threshold of sound intensity = 1 x 10⁻¹² W/m²
The intensity of sound at a rock concert
[tex]120 = 10Log(\frac{I}{1*10^{-12}} )\\\\12 = Log(\frac{I}{1*10^{-12}} )\\\\\frac{I}{1*10^{-12}} = 10^{12}\\\\I = 1*10^{-12} *10^{12}\\\\I = 1*10^0\\\\I =1 \ W/m^2[/tex]
The intensity of sound of a whisper
[tex]20 = 10Log(\frac{I}{1*10^{-12}} )\\\\2 = Log(\frac{I}{1*10^{-12}} )\\\\\frac{I}{1*10^{-12}} = 10^{2}\\\\I = 1*10^{-12} *10^{2}\\\\I = 1*10^{-10}\\\\I =10^{-10} \ W/m^2[/tex]
Thus, the intensity of sound at rock concert is 10¹⁰ greater than that of a whisper.
You are trying to push a 14 kg canoe across a beach to get it to a lake. Initially, the canoe is at rest, and you exert a force over a distance of 5 m until it has a speed of 2.1 m/s.
a. How much work was done on the canoe?
b. The coefficient of kinetic friction between the canoe and the beach is 0.2. How much work was done by friction on the canoe?
c. How much work did you perform on the canoe?
d. What force did you apply to the canoe?
Answer:
I hope this is correct!
Explanation:
a) work = (force)(displacement)
We know that d = 5m, now we just need to find the force
We need to calculate the acceleration first using a = v^2 - u^2 / 2d
final velocity (v) = 2.1 m/s , initial velocity (u) = 0 m/s , displacement (d) = 5m
a = 2.1^2 - 0^2 / 2(5)
= 0.441 m/s^2
Now we can find force using f = ma
f = (14kg)(0.441m/s^2)
= 6.174 newtons
Finally, you can calculate work now that you have force!
work = (6.174n)(5m)
= 30.87 J (you may need to round sig figs!)
b) Work done by friction = (coefficient of kinetic friction)(mg)(v)
m = 14kg, g = 9.8, coefficient of friction = 0.2
force due to friction = (0.2)(14kg x 9.8)(2.1)
= 57.624 J (again you may need to round to sig figs)
c) Work you perform = total work in direction of motion + work done by friction
total work = 30.87 J, work done by friction = 57.624 J
Work you perform = 30.84 + 57.624
= 88.464 J
d) Force you applied = work you performed / distance
work you performed = 88.464 / 5 m
= 17.6929 N (again you may need to round to sig figs)
Hope this helps ya! Best of luck <3
If the distance from your eye's lens to the retina is shorter than for a normal eye, you will struggle to see objects that are
Answer:
far away
Explanation:
There are different types of eye defect ranging from short sightedness, longsighted, astigmatism, presbyopia etc.
If someone is only able to see close ranged object clearly but not far distant object, then such person is suffering from short sightedness or myopia. This occurs when the light rays entering the eye does not converge on the retina. Instead of converging on the retina, the light ray is formed on a point in front of the retina. This causes the distance from the eye's lens to the retina shorter compared to that of a normal eye. This eye defect is usually corrected using concave lens in order to diverge the rays thereby allowing it to focus on the retina.
Hence, if the distance from your eye's lens to the retina is shorter than for a normal eye, you will struggle to see objects that are far away (at a far distant).
You spaceship has a snazzy lounge called Ten-Forward that needs a new spacecouch. Sadly the couch you bought is too long and won't fit into your car when it is stationary. The couch has a length Lc = 14.0 m and mass m = 49 kg, and your shuttlecraft has a length of L = 9.0 m How fast would you need to run, in terms of the speed of light c, in order to get the couch to fit inside the length of the shuttlecraft?
Answer:
v = speed
c = speed of light
using the equation
L = Lc Sqrt( 1 - (v/c)2)
9 = 14 Sqrt( 1 - (v/c)2)
v/c = 0.765
v = 0.765 c
An undiscovered planet, many light-years from Earth, has one moon, which has a nearly circular periodic orbit. If the distance from the center of the moon to the surface of the planet is 2.165×105 km and the planet has a radius of 4175 km and a mass of 6.70×1022 kg , how long (in days) does it take the moon to make one revolution around the planet? The gravitational constant is 6.67×10−11N·m2/kg2 .
Answer:
364days
Explanation:
Pls see attached file
Explanation:
The moon will take 112.7 days to make one revolution around the planet.
What is Kepler's third law?The period of the satellite around any planet only depends upon the distance between the planet's center and satellite and also depends upon the planet's mass.
Given, the distance from the moon's center to the planet's surface,
h = 2.165 × 10⁵ km,
The radius of the planet, r = 4175 km
The mass of the planet = 6.70 × 10²² kg
The total distance between the moon's center to the planet's center:
a = r +h = 2.165 × 10⁵ + 4175
a = 216500 + 4175
a = 220675
a = 2.26750 × 10⁸ m
The period of the planet can be calculated as:
[tex]T =2\pi \sqrt{\frac{a^3}{Gm} }[/tex]
[tex]T =2\3\times 3.14 \sqrt{\frac{(2.20675 \times 10^8)^3}{(6.67\times 10^{-11}).(6.70\times 10^{22})} }[/tex]
T = 9738253.26 s
T = 112.7 days
Learn more about Kepler's law, here:
https://brainly.com/question/1608361
#SPJ5
The near point (the smallest distance at which an object can be seen clearly) and the far point (the largest distance at which an object can be seen clearly) are measured for six different people.
Near Point(cm) Far Point(cm)
Avishka 40 [infinity]
Berenice 30 300
Chadwick 25 500
Danya 25 [infinity]
Edouard 80 200
Francesca 50 [infinity]
Of the farsighted people, rank them by the power of the lens needed to correct their hyperopic vision. Rank these from largest to smallest power required.
1. Berenice
2. Avishka
3. Francesca
4. Edouard
Answer:
1. Berenice = 0.67 D
2. Avishka = 1.50 D
3. Francesca = 2.00 D
4. Edouard = 2.75 D
Explanation:
The farsighted people are those with near point greater than 25 cm.
They include Avishka, Berenice, Edouard and Francisca.
A converging lens is needed to correct farsightedness, or hyperopia, therefore, the focal length, f, is positive. The image formed is virtual and on the same side of the lens. Thus the image distance is negative
From the lens formula, 1/f = 1/v 1/u; but v is negative
Therefore, 1/f = 1/u - 1/v
But, power of a lens = 1/f in meters.
Therefore, P = 1/u - 1/v
For Avishka, u = 25 cm or 0.25 m, v = 0.4 m
P = 1/ 0.25 - 1/0.4 = 1.5 D
For Berenice, u = 0.25 m, v = 0.3 m
P = 1/0.25 - 1/0.30 =0.7 D
For Edouard, u = 0.25 m, v = 0.80 m
P = 1/0.25 - 1/0.80 =2.75 D
For Francesca, u = 0.25 m, v = 0.50 m
P = 1/0.25 - 1/0.5 = 2.0 D
When The farsighted people are those with a near point greater than 25cm.
Berenice is = 0.67 D
Avishka is = 1.50 D
Francesca is = 2.00 D
Edouard is = 2.75 D
What is Hyperopic Vision?
When The farsighted people are those with a near point greater than 25 cm. Then, They include Avishka, Berenice, Edouard, and also Francisca.
Also, A converging lens is needed to correct farsightedness, or hyperopia, thus, When the focal length, f, is positive. Also, The image formed is virtual and also on the same side of the lens. hence the image distance is negative.
Also, From the lens formula, 1/f = 1/v 1/u; but v is negative
Thus, 1/f = 1/u - 1/v
But, when the power of a lens = 1/f in meters.
Thus, P = 1/u - 1/v
For Avishka, u = 25 cm or 0.25 m, v = 0.4 m
After that, P = 1/ 0.25 - 1/0.4 = 1.5 D
Then, For Berenice, u = 0.25 m, v = 0.3 m
Now, P = 1/0.25 - 1/0.30 =0.7 D
For Edouard, u = 0.25 m, v is = 0.80 m
Then, P = 1/0.25 - 1/0.80 is =2.75 D
Now, For Francesca, u = 0.25 m, v is = 0.50 m
Therefore, P = 1/0.25 - 1/0.5 = 2.0 D
Find more information about Hyperopic Vision here:
https://brainly.com/question/25676535
A collector that has better efficiency in cold weather is the:
flat-plate collector due to reduced heat loss
evacuated tube collector due to its larger size
flat-plate collector due to the dark-colored coating
O evacuated tube collector due to reduced heat loss
Question 23 (1 point) Saved
One of the following is not found in Thermosyphon systems
o
Answer:
D. evacuated tube collector due to reduced heat loss
Explanation:
Evacuated tube collectors has vacuum which reduces the loss of heat and increase the efficiency of the collector. It has a major application in solar collector, and converts solar energy to heat energy. It can also be used for heating of a definite volume of water majorly for domestic purpose.
During cold weather, the conservation and efficient use of heat is required. Therefore, evacuated tube collector is preferred so as to reduce heat loss and ensure the maximum use of heat energy.
Consider two parallel wires where the magnitude of the left currentis 2 I0(io) and that of the right current is I0(io). Point A is midway between the wires,and B is an equal distance on the other side of the wires.
The ratio ofthe magnitude of the magnetic field at point A to that at point Bis________
Answer:
Explanation:
At the point midway between wires
magnetic field due to wire having current 2I₀
= 10⁻⁷ x 2 x2I₀ / r where 2r is the distance between wires .
magnetic field due to wire having current I₀
= 10⁻⁷ x 4 I₀ / r
magnetic field due to wire having current I₀
= 10⁻⁷ x 2I₀ / r
= 10⁻⁷ x 2 I₀ / r where 2r is the distance between wires .
these fields are in opposite direction as direction of current is same in both .
net magnetic field = (4 - 2 )x 10⁻⁷ x I₀ / r
= 2 x 10⁻⁷ x I₀ / r
At point A net magnetic field = 2 x 10⁻⁷ x I₀ / r
At point B , we shall calculate magnetic field
magnetic field due to nearer wire having current 2 I₀ = 10⁻⁷ x 4 I₀ / r
magnetic field due to wire far away = 10⁻⁷ x 2 I₀ / 3r
These magnetic fields act in the same direction so they will add up
net magnetic field = [ (4 I₀ / r) + (2 I₀ / 3r) ] x 10⁻⁷
= (14 I₀ / 3r ) x 10⁻⁷
Magnetic field at point B = (14 I₀ / 3r ) x 10⁻⁷
Ratio of field at A and B
= 3 / 7 . Ans
The ratio of the magnitude of the magnetic field at point A to point B is :
3 / 7
Given data :
Magnitude of the left current is 2I₀
Magnitude of the right current is I₀
First step : Determine the magnetic field at point A
The magnetic field due to the left current ( 2I₀ )
10⁻⁷ * 2 * 2I₀ / r ( 2r = distance between wires )
The magnetic field due to the right current ( I₀ )
10⁻⁷ * 2 I₀ / r
From the expressions above the magnetic fields are in opposite direction
∴ Net magnetic field = (4 - 2 )* 10⁻⁷ * I₀ / r = 2 * 10⁻⁷ * I₀ / r
Hence The magnetic field at point A = 2 * 10⁻⁷ * I₀ / r
Next step : determine the magnetic field at point B
Magnetic field due to the closest wire to point B ( i.e.2I₀ ) = 10⁻⁷ * 4 I₀ / r
Magnetic field due to the wire away from point A = 10⁻⁷ * 2 I₀ / 3r
Since the fields acts in the same directions
The net magnetic field = (4 I₀ / r) + (2 I₀ / 3r) ] * 10⁻⁷ = ( 14 I₀ / 3r ) * 10⁻⁷
Hence The magnetic field at point A = ( 14 I₀ / 3r ) * 10⁻⁷
Therefore the ratio of the magnitude of the magnetic field at point A to point B = 3/ 7
Hence we can conclude that the ratio of the magnitude of the magnetic field at point A to point B = 3 / 7
Learn more : https://brainly.com/question/22403676
how can you relazie a perfect balck body in pratice
Given that two vectors A = 5i-7j-3k, B = -4i+4j-8k find A×B
[tex]\textbf{A}×\textbf{B}= 68\hat{\textbf{i}} + 52\hat{\textbf{j}} - 8\hat{\textbf{k}}[/tex]
Explanation:
Given:
[tex]\textbf{A} = 5\hat{\textbf{i}} - 7\hat{\textbf{j}} - 3\hat{\textbf{k}}[/tex]
[tex]\textbf{B} = -4\hat{\textbf{i}} + 4\hat{\textbf{j}} - 8\hat{\textbf{k}}[/tex]
The cross product [tex]\textbf{A}×\textbf{B}[/tex] is given by
[tex]\textbf{A}×\textbf{B} = \left|\begin{array}{ccc}\hat{\textbf{i}} & \hat{\textbf{j}} & \hat{\textbf{k}} \\\:\:5 & -7 & -3 \\ -4 & \:\:4 & -8 \\ \end{array}\right|[/tex]
[tex]= \left|\begin{array}{cc}-7 & -3\\\:4 & -8\\ \end{array}\right|\:\hat{\textbf{i}}\:+\:\left|\begin{array}{cc}-3 & \:\:5\\-8 & -4\\ \end{array}\right|\:\hat{\textbf{j}}\:+\: \left|\begin{array}{cc}\:\:5 & -7\\-4 & \:\:4\\ \end{array}\right|\:\hat{\textbf{k}}[/tex]
[tex]= 68\hat{\textbf{i}} + 52\hat{\textbf{j}} - 8\hat{\textbf{k}}[/tex]
A single-turn current loop carrying a 4.00 A current, is in the shape of a right-angle triangle with sides of 50.0 cm, 120 cm, and 130 cm. The loop is in a uniform magnetic field of magnitude 75.0 mT whose direction is parallel to the current in the 130 cm side of the loop. What is the magnitude of the magnetic force on the
Given that,
Current = 4 A
Sides of triangle = 50.0 cm, 120 cm and 130 cm
Magnetic field = 75.0 mT
Distance = 130 cm
We need to calculate the angle α
Using cosine law
[tex]120^2=130^2+50^2-2\times130\times50\cos\alpha[/tex]
[tex]\cos\alpha=\dfrac{120^2-130^2-50^2}{2\times130\times50}[/tex]
[tex]\alpha=\cos^{-1}(0.3846)[/tex]
[tex]\alpha=67.38^{\circ}[/tex]
We need to calculate the angle β
Using cosine law
[tex]50^2=130^2+120^2-2\times130\times120\cos\beta[/tex]
[tex]\cos\beta=\dfrac{50^2-130^2-120^2}{2\times130\times120}[/tex]
[tex]\beta=\cos^{-1}(0.923)[/tex]
[tex]\beta=22.63^{\circ}[/tex]
We need to calculate the force on 130 cm side
Using formula of force
[tex]F_{130}=ILB\sin\theta[/tex]
[tex]F_{130}=4\times130\times10^{-2}\times75\times10^{-3}\sin0[/tex]
[tex]F_{130}=0[/tex]
We need to calculate the force on 120 cm side
Using formula of force
[tex]F_{120}=ILB\sin\beta[/tex]
[tex]F_{120}=4\times120\times10^{-2}\times75\times10^{-3}\sin22.63[/tex]
[tex]F_{120}=0.1385\ N[/tex]
The direction of force is out of page.
We need to calculate the force on 50 cm side
Using formula of force
[tex]F_{50}=ILB\sin\alpha[/tex]
[tex]F_{50}=4\times50\times10^{-2}\times75\times10^{-3}\sin67.38[/tex]
[tex]F_{50}=0.1385\ N[/tex]
The direction of force is into page.
Hence, The magnitude of the magnetic force on each of the three sides of the loop are 0 N, 0.1385 N and 0.1385 N.
a. The magnitude of the magnetic force on the 130 cm side is 0 Newton.
b. The magnitude of the magnetic force on the 120 cm side is 0.1385 Newton.
c. The magnitude of the magnetic force on the 50 cm side is 0.1385 Newton.
Given the following data:
Current = 4.00 Amperes.Magnetic field strength = 75.0 mT = [tex]7.5 \times 20^{-3}\;T[/tex]Length = 130 cm to m = 1.3 mHypotenuse = 130 cmOpposite side = 120 cmAdjacent side = 50 cmLet us assume the current is flowing in a counterclockwise direction in the right-angle triangle.
First of all, we would determine the angles by using cosine rule:
[tex]C^2=A^2 +B^2 - 2ABCos\alpha \\\\120^2=130^2 +50^2 - 2(130)(50)Cos\alpha\\\\14400 = 16900 + 2500 -13000Cos\alpha\\\\13000Cos\alpha=19400-14400 \\\\Cos\alpha=\frac{5000}{13000} \\\\\alpha = Cos^{-1}(0.3846)\\\\\alpha =67.38^\circ[/tex]
[tex]C^2=A^2 +B^2 - 2ABCos\beta \\\\50^2=120^2 +130^2 - 2(120)(130)Cos\beta \\\\2500 = 14400 + 16900 -31200Cos\beta\\\\31200Cos\alpha=31300-2500 \\\\Cos\beta=\frac{28800}{31200} \\\\\beta = Cos^{-1}(0.9231)\\\\\beta =22.62^\circ[/tex]
a. To the determine the magnitude of the magnetic force on the 130 cm side:
Mathematically, the force acting on a current in a magnetic field is given by the formula:
[tex]F = BILsin\theta[/tex]
Where:
B is the magnetic field strength.I is the current flowing through a conductor.L is the length of conductor.[tex]\theta[/tex] is the angle between a conductor and the magnetic field.Substituting the given parameters into the formula, we have;
[tex]F_{130}=7.5 \times 20^{-3}\times 4 \times 1.3 \times sin(0)\\\\F_{130}=7.5 \times 20^{-3}\times 4 \times 1.3 \times0\\\\F_{130}=0\;Newton[/tex]
b. To the determine the magnitude of the magnetic force on the 120 cm side:
[tex]F_{120}=BILsin\beta[/tex]
[tex]F_{120}=7.5 \times 20^{-3}\times 4 \times 1.2 \times sin(22.62)\\\\F_{120}=7.5 \times 20^{-3}\times 4 \times 1.2 \times0.3846\\\\F_{120}=0.1385\;Newton[/tex]
c. To the determine the magnitude of the magnetic force on the 50 cm side:
[tex]F_{50}=BILsin\alpha[/tex]
[tex]F_{50}=7.5 \times 20^{-3}\times 4 \times 0.5 \times sin(67.38)\\\\F_{50}=7.5 \times 20^{-3}\times 4 \times 1.2 \times0.9231\\\\F_{50}=0.1385\;Newton[/tex]
Read more: https://brainly.com/question/13754413
A wire of 0.50m length is suspended by a pair of flexible leads in a uniform magnetic field of magnitude 0.98T. The vurrent in the wire is 2.0A in the direction shown. What is the mass of the wire if the current and the magnetic field are sufficient to remove the tension in the supporting leads?
Answer:
0.1 kg or 100 g
Explanation:
The length of the wire = 0.5 m
the field magnitude = 0.98 T
the current through the wire = 2.0 A
magnetic force due to a wire carrying current is
F = [tex]IlB[/tex]
where
F is the force
[tex]I[/tex] is the current = 2 A
[tex]l[/tex] is the length of the wire
B is the magnetic field strength
Substituting, we have
F = 2 x 0.5 x 0.98 = 0.98 N
This force balances the weight of the mass
weight = mg
where m is the mass of the wire
g is acceleration due to gravity = 9.81 m/s^2
therefore, weight = m x 9.81 = 9.81m
equating this weight with the force, we have
0.98 = 9.81m
m = 0.98/9.81 = 0.099 kg ≅ 0.1 kg or 100 g
Answer:
100 g
Explanation:
find the velocity of the object for all relevent times find the position of the object for all relevent times a softball is popped up vertically velocity of 32 m/s
Answer:
whats the formula
Explanation:
Rod cells in the retina of the eye detect light using a photopigment called rhodopsin. 1.8 eV is the lowest photon energy that can trigger a response in rhodopsin. Part A What is the maximum wavelength of electromagnetic radiation that can cause a transition
Answer:
The maximum wavelength of the e-m wave is 6.9 x 10^-7 m
Explanation:
Energy required to trigger a response = 1.8 eV
we convert to energy in Joules.
1 eV = 1.602 x 10^-19 J
1.8 eV = [tex]x[/tex] J
[tex]x[/tex] = 1.8 x 1.602 x 10^-19 = 2.88 x 10^-19 J
The energy of an electromagnetic wave is gotten as
E = hf
where
h is the Planck's constant = 6.63 x 10^-34 J-s
and f is the frequency of the wave.
substituting values, we have
2.88 x 10^-19 = 6.63 x 10^-34 x f
f = (2.88 x 10^-19)/(6.63 x 10^-34)
f = 4.34 x 10^14 Hz
We know that the frequency of an e-m wave is given as
f = c/λ
where
c is the speed of light = 3 x 10^8 m/s
λ is the wavelength of the e-m wave
From this we can say that
λ = c/f
λ = (3 x 10^8)/(4.34 x 10^14)
λ = 6.9 x 10^-7 m
How long will it take a spacecraft travelling at 99% the speed of light (gamma = 7) to reach
the star Sirius which is 8.6 light-years away according to people on Earth ? How long will it
take according to the crew of the ship?
Answer:
The time taken is [tex]t = 2.739 *10^{8} \ s[/tex]
Explanation:
From the question we are told that
The speed of the spacecraft is [tex]v = 0.99c[/tex]
where c is the speed of light with value [tex]c = 3.0*10^{8} \ m/s[/tex]
=> [tex]v = 0.99 * 3.0 *10^{8 } = 2.97*10^{8}\ m/s[/tex]
The distance of Sirius is [tex]d = 8.6 \ light-years = 8.6 * 9.461*10^{15}= 8.135*10^{16} \ m[/tex]
Generally the time taken is mathematically represented as
[tex]t = \frac{d}{v}[/tex]
substituting values
[tex]t = \frac{8.136 *10^{16}}{2.97 *10^{8}}[/tex]
[tex]t = 2.739 *10^{8} \ s[/tex]
Two long straight wires carry currents perpendicular to the xy plane. One carries a current of 50 A and passes through the point x = 5.0 cm on the x axis. The second wire has a current of 80 A and passes through the point y = 4.0 cm on the y axis. What is the magnitude of the resulting magnetic field at the origin?
Answer:
450 x10^-6 T
Explanation:
We know that the magnetic of each wire is derived from
ByB= uoi/2pir
Thus B1= 4 x 3.14 x 10^-7 x50/( 2 x 3.142x 0.05)
= 0.2 x 10^ -3T
B2=
4 x 3.14 x 10^-7 x80/( 2 x 3.142x 0.04)
= 0.4 x 10^ -3T
So
(Bnet)² = (Bx)² + ( By)²
= (0.2² + 0.4²)mT
= 450 x10^-6T
The magnitude of magnetic field at the origin is required.
The magnitude of resulting magnetic field at origin is [tex]447.2\ \mu\text{T}[/tex]
x = Location at x axis = 5 cm
y = Location at y axis = 4 cm
[tex]I_x[/tex] = Current at the x axis point = 50 A
[tex]I_y[/tex] = Current at the y axis point = 80 A
[tex]\mu_0[/tex] = Vacuum permeability = [tex]4\pi\times 10^{-7}\ \text{H/m}[/tex]
Magnitude of the magnetic field is given by
[tex]B=\dfrac{\mu_0I}{2\pi r}[/tex]
Finding the net magnetic field using the Pythagoras theorem
[tex]B^2=B_x^2+B_y^2\\\Rightarrow B^2=\left(\dfrac{\mu_0I_x}{2\pi x}\right)^2+\left(\dfrac{\mu_0I_y}{2\pi y}\right)^2\\\Rightarrow B=\dfrac{\mu_0}{2\pi}\sqrt{\left(\dfrac{I_x}{x}\right)^2+\left(\dfrac{I_y}{y}\right)^2}\\\Rightarrow B=\dfrac{4\pi\times 10^{-7}}{2\pi}\sqrt{\left(\dfrac{50}{0.05}\right)^2+\left(\dfrac{80}{0.04}\right)^2}\\\Rightarrow B=0.0004472=447.2\ \mu\text{T}[/tex]
The magnitude of resulting magnetic field at origin is [tex]447.2\ \mu\text{T}[/tex]
Learn more:
https://brainly.com/question/14573987?referrer=searchResults
A particle moves along line segments from the origin to the points (1, 0, 0), (1, 5, 1), (0, 5, 1), and back to the origin under the influence of the force field. F(x, y, z)= z^2i + 4xyj + 5y^2kFind the work done.
Answer:
0 J
Explanation:
Since work done W = ∫F.dr and F(x, y, z)= z²i + 4xyj + 5y²k and dr = dxi + dyj + dzk
F.dr = (z²i + 4xyj + 5y²k).(dxi + dyj + dzk) = z²dx + 4xydy + 5y²dz
W = ∫F.dr = ∫z²dx + 4xydy + 5y²dz = z²x + 2xy² + 5y²z
We now evaluate the work done for the different regions
W₁ = work done from (0,0,0) to (1,0,0)
W₁ = {z²x + 2xy² + 5y²z}₀₀₀¹⁰⁰ = 0²(1) + 2(1)(0)² + 5(0)²(0) - [(0)²(0) + 2(0)(0)² + 5(0)²(0)] = 0 - 0 = 0 J
W₂ = work done from (1,0,0) to (1,5,1)
W₂ = {z²x + 2xy² + 5y²z}₁₀₀¹⁵¹ = (1)²(1) + 2(1)(5)² + 5(5)²(1) - [0²(1) + 2(1)(0)² + 5(0)²(0)] = 1 + 50 + 125 - 0 = 176 J
W₃ = work done from (1,5,1) to (0,5,1)
W₃ = {z²x + 2xy² + 5y²z}₁₅₁⁰⁵¹ = 1²(0) + 2(0)(5)² + 5(5)²(1) - [(1)²(1) + 2(1)(5)² + 5(5)²(1)] = 125 - (1 + 50 + 125) = 125 - 176 = -51 J
W₄ = work done from (0,5,1) to (0,0,0)
W₄ = {z²x + 2xy² + 5y²z}₁₅₁⁰⁰⁰ = (0)²(0) + 2(0)(0)² + 5(0)²(0) - [1²(0) + 2(0)(5)² + 5(5)²(1)] = 0 - 125 = -125 J
The total work done W is thus
W = W₁ + W₂ + W₃ + W₄
W = 0 J + 176 J - 51 J - 125 J
W = 176 J - 176 J
W = 0 J
The total work done equals 0 J
A steel bridge is 1000 m long at -20°C in winter. What is the change in length when the temperature rises to 40°C in summer? The average coefficient of linear expansion of this steel is 11 × 10-6 C-1.
Answer:
ΔL = 0.66 m
Explanation:
The change in length on an object due to rise in temperature is given by the following equation of linear thermal expansion:
ΔL = αLΔT
where,
ΔL = Change in Length of the bridge = ?
α = Coefficient of linear thermal expansion = 11 x 10⁻⁶ °C⁻¹
L = Original Length of the Bridge = 1000 m
ΔT = Change in Temperature = Final Temperature - Initial Temperature
ΔT = 40°C - (-20°C) = 60°C
Therefore,
ΔL = (11 x 10⁻⁶ °C⁻¹)(1000 m)(60°C)
ΔL = 0.66 m
the plane of a 5.0 cm by 8.0 cm rectangular loop wire is parallel to a 0.19 t magnetic field. if the loop carries a current of 6.2 amps, what is the magnitude of the torque on the loop