Drag force is a resistive force exerted on an object moving through a fluid, such as air or water. It opposes the object's motion and is proportional to the object's velocity and the fluid's density.
Given data: Size of building = 25 m x 10 m x 12 m = 3000 m³ Wind velocity = 6 m/sFlow velocity = 0.8 m/s
a) Dry season. In the dry season, there is no possibility of a drag force acting on the building because of the absence of water.
b) Partly submerged. When the building is partly submerged, then drag force F can be given as:
F = (1/2) x (density of water) x (velocity of water)² x Cd x A
Where, Cd = drag coefficient ,
A = area of the building
= 2(25x10) + 2(10x12) + 2(25x12)
= 850 m²
F = (1/2) x (1000) x (0.8)² x 1.2 x 850
F = 231,840 N (approx)
c) Mostly submerged. When the building is mostly submerged, then drag force F can be given as:
F = (1/2) x (density of water) x (velocity of water)² x Cd x A
Where, Cd = drag coefficient,
A = area of the building = 2(25x10) + 2(10x12) + 2(25x12)
= 850 m²
(the same as in b)
F = (1/2) x (1000) x (0.8)² x 1.1 x 850F = 198,264 N (approx)
Problem that could be occurred when this building submerged underwater:
When the building is submerged underwater, the drag force increases, which can cause structural instability, especially if it is not designed to withstand such forces.
In addition, the buoyancy of the building can change, and the weight can increase due to waterlogging, leading to the sinking of the building.
To know more about Drag force visit:
https://brainly.com/question/13385370
#SPJ11
The weak form of the governing equation is: So v₂ E Au dx = fvqdx + [vEAux] - fEAv, up dx, where u is the displacement. Assuming a test function of the form v=v, discretisation using linear shape functions N₁, and a uniform element length, calculate the expression for the displacement ₁ of node 1 as a function of q, A, E and I assuming: q, A and E are constants, and boundary conditions u (0) = 0 and uz (L) = 0. Denote the element length by 1. Using this information, please answer questions 3-6. Evaluate the term fo v E Aude for this specific problem. Input only the solution below. Omit the hats to simplify inputting the solution. Evaluate the term fvqda for the specific example above. Input only the solution below. Omit the hats to simplify inputting the solution. Evaluate the term [vE Au for the specific example above. Input only the solution below. Omit the hats to simplify inputting the solution. Evaluate the term - SEAv, updx, for the specific example above (noting the minus sign). Input only the solution below. Omit the hats to simplify inputting the solution.
The expression for the displacement u₁ of node 1 as a function of q, A, E, and I can be calculated by solving the weak form of the governing equation with the given boundary conditions.
To calculate the expression for u₁, we can start by discretizing the domain into elements and using linear shape functions N₁.
Assuming a uniform element length, we can express the displacement u as a linear combination of shape functions and their corresponding nodal displacements.
Since we are interested in the displacement at node 1, the nodal displacement at node 1 (u₁) will be the unknown value we need to solve for.
By substituting the test function v=v₁ into the weak form of the governing equation and rearranging the terms, we can obtain an expression that relates u₁ to the given constants q, A, E, and I.
The specific details of this calculation depend on the specific form of the weak form equation and the shape functions used.
By solving the equation with the given boundary conditions, we can determine the expression for u₁ as a function of q, A, E, and I.
Learn more about governing equation
brainly.com/question/32178187
#SPJ11
A flat-panel domestic heater 1 m tall x 2 m long is used to maintain a room at 20 °C. An electrical element keeps the surfaces of the radiator at 65 °C. Approximating the heater as a vertical flat plate, calculate the heat transferred to the room by natural convection from both surfaces of the heater (front and back). Assuming that the surface of the heater is painted white, calculate the heat transferred from the radiator to the surrounding surfaces by radiation. Note: The emissivity value of white paint for longwave radiation is approximately 0.8.
The heat transferred from the radiator to the surrounding surfaces by radiation is 321.56 W.
Given that the flat-panel domestic heater is 1 m tall and 2 m long. The heater maintains the room temperature at 20°C. The electrical element keeps the surface temperature of the radiator at 65°C. The heater is approximated as a vertical flat plate. The heat transferred to the room by natural convection from both surfaces of the heater (front and back) can be calculated using the following formula;
Q = h × A × (ΔT)
Q = heat transferred
h = heat transfer coefficient
A = surface are (front and back)
ΔT = temperature difference = 65 - 20 = 45°C
For natural convection, the value of h is given by;
h = k × (ΔT)^1/4
Where k = 0.15 W/m2K
For the front side;
A = 1 × 2 = 2 m2
h = 0.15 × (45)^1/4 = 3.83 W/m2K
Q = h × A × (ΔT)Q = 3.83 × 2 × 45 = 344.7 W
For the back side, the temperature difference will be the same but the surface area will change.
Area of back side = 1 × 2 = 2 m2
h = 0.15 × (45)^1/4 = 3.83 W/m2K
Q = h × A × (ΔT)Q = 3.83 × 2 × 45 = 344.7 W
The total heat transferred by natural convection from the front and back surface is;
Qtotal = 344.7 + 344.7 = 689.4 W
The heat transferred from the radiator to the surrounding surfaces by radiation can be calculated using the following formula;
Q = σ × A × ε × (ΔT)^4
Where σ = 5.67 × 10-8 W/m2K
4A = 1 × 2 = 2 m2
ΔT = (65 + 273) - (20 + 273) = 45°C
Emissivity ε = 0.8Q = 5.67 × 10-8 × 2 × 0.8 × (45)^4Q = 321.56 W
Therefore, the heat transferred from the radiator to the surrounding surfaces by radiation is 321.56 W.
Learn more about natural convection visit:
brainly.com/question/29451753
#SPJ11
The work function of a metal surface is 4.5 eV. If the frequency of the light incident upon it is 1.45 × 1015 Hz, then what is the maximum kinetic energy (in eV) of the photo electrons emitted from the surface?
The maximum kinetic energy (in eV) of the photo electrons emitted from the surface is 6 ev.
To calculate the maximum kinetic energy of photoelectrons emitted from a metal surface, we can use the equation:
E max=hν−φ
Where: E max is the maximum kinetic energy of photoelectrons,
h is the Planck's constant (4.135667696 × 10⁻¹⁵ eV s),
ν is the frequency of the incident light (1.45 × 10¹⁵ Hz),
φ is the work function of the metal surface (4.5 eV).
Plugging in the values:
E max =(4.135667696×10⁻¹⁵ eV s)×(1.45×10¹⁵ Hz)−4.5eV
Calculating the expression:
E max =5.999eV
To learn more on Work click:
https://brainly.com/question/18094932
#SPJ4
By considering the mechanical behaviour of polymers in terms of spring and dashpot models, describe and explain (with the aid of diagrams) the four systems that can represent the response of a polymer to a stress pulse. Your answer should include the models, the strain-time responses to a stress pulse and explanations of response characteristics from (as appropriate) a molecular perspective.
Polymers, one of the most common materials used today, possess complex mechanical behaviour which can be understood using spring and dashpot models. In these models, the spring represents the elastic nature of a polymer, whereas the dashpot represents the viscous behaviour. The four systems that represent the response of a polymer to a stress pulse include:
1. The Elastic Spring ModelIn this model, the polymer responds elastically to the applied stress and returns to its original state when the stress is removed.2. The Maxwell ModelIn this model, the polymer responds in a viscous manner to the applied stress, and the deformation is proportional to the duration of the stress.3. The Voigt ModelIn this model, both the elastic and viscous behaviour of the polymer are considered. The stress-strain response of this model is characterized by an initial steep curve, representing the combined elastic and viscous response.
4. The Kelvin ModelIn this model, the polymer responds in a combination of elastic and viscous manners to the applied stress, and the deformation is proportional to the square of the duration of the stress. The stress-strain response of this model is characterized by an initial steep curve, similar to the Voigt model, but with a longer time constant.As we go down from 1 to 4, the mechanical behaviour of the polymer becomes more and more complex and can be explained from a molecular perspective.
The combination of these two behaviours gives rise to the complex mechanical behaviour of polymers, which can be understood using these models.
To know more about mechanical behaviour visit :
https://brainly.com/question/25758976
#SPJ11
a) Given the equation below: i. Show the simplified Boolean equation below by using the K-Map technique. (C3, CLO3) ii. Sketch the simplified circuit-based result in (ai) (C3,CLO3) b) Given the equation below: i. Show the simplify the logic expression z=ABC+ Ā + ABC by using the Boolean Algebra technique. ii. Sketch the simplified circuit-based result in (bi) (C3, CLO3)
a)Given the equation, F (A, B, C, D) = ∑ (0, 2, 4, 6, 10, 11, 12, 13) with two bits per cell. Here is how to solve it using the K-Map technique :i. C2 and C3 are the row and column headings.
The table has four rows and four columns. Therefore, we use the following table. The K-Map for F(A,B,C,D)F (A, B, C, D) = A'C'D' + A'B'D' + A'BCD + ABCD 'ii. A simplified circuit-based result Circuit Diagram for F (A, B, C, D) = A'C'D' + A'B'D' + A'BCD + ABCD 'b)Given the equation z = ABC + Ā + ABC.
Here is how to solve it using the Boolean Algebra technique: i. Logic Expression Simplification z = ABC + Ā + ABC (Identity Property)z = ABC + ABC + Ā (Associative Property)z = AB(C + C) + Āz = AB + Ā ii. Simplified Circuit-based Result Circuit Diagram for z = AB + Ā
To know more about technique visit:
brainly.com/question/31609703
#SPJ11
How would you link the capacity decision being made by Fitness Plus to other types of operating decisions?
Fitness Plus, an emerging fitness and gym provider, is trying to gain a significant share of the market in the region, making it a major competitor to other industry players. Fitness Plus's decision to expand its capacity is critical, and it influences the types of operating decisions they make, including marketing, financial, and human resource decisions.
Capacity decisions at Fitness Plus are linked to marketing decisions in several ways. When Fitness Plus decides to expand its capacity, it means that it is increasing the number of customers it can serve simultaneously. The expansion creates an opportunity to increase sales by catering to a more extensive market. Fitness Plus's marketing team must focus on building brand awareness to attract new customers and create loyalty among existing customers.The expansion also influences financial decisions. Fitness Plus must secure funding to finance the expansion project.
It means that the financial team must identify potential sources of financing, analyze their options, and determine the most cost-effective alternative. Fitness Plus's decision to expand its capacity will also have a significant impact on its human resource decisions. The expansion creates new job opportunities, which Fitness Plus must fill. Fitness Plus must evaluate its staffing requirements and plan its recruitment strategy to attract the most qualified candidates.
In conclusion, Fitness Plus's decision to expand its capacity has a significant impact on its operating decisions. The expansion influences marketing, financial, and human resource decisions. By considering these decisions together, Fitness Plus can achieve its growth objectives and increase its market share in the region.
To know more about fitness visit :
https://brainly.com/question/31252433
#SPJ11
The internal energy of a monatomic gas can be treated as having an RT/2 contribution for each directional degree of freedom. Using this kinetic energy model, calculate (a) the constant-volume molar specific heat, kJ/kgmole-K; (b) the constant-pressure molar specific heat, kJ/kgmole-K; and (c) the molar specific heat ratio for a monatomic gas.
(a) The constant-volume molar specific heat for a monatomic gas is R/2 kJ/kgmole-K.
(b) The constant-pressure molar specific heat for a monatomic gas is R kJ/kgmole-K.
(c) The molar specific heat ratio for a monatomic gas is γ = 5/3 or 1.67.
Step 1: Constant-volume molar specific heat (a)
The constant-volume molar specific heat, denoted as Cv, represents the amount of heat required to raise the temperature of one mole of a gas by one Kelvin at constant volume. For a monatomic gas, each atom has three translational degrees of freedom. According to the kinetic energy model, the internal energy of the gas can be treated as having an RT/2 contribution for each degree of freedom. Since a mole of gas contains Avogadro's number (Na) of atoms, the total internal energy contribution is Na * (3/2) * RT/2 = 3/2 * R, where R is the ideal gas constant. Thus, the constant-volume molar specific heat is Cv = 3/2 * R/Na = R/2 kJ/kgmole-K.
Step 2: Constant-pressure molar specific heat (b)
The constant-pressure molar specific heat, denoted as Cp, represents the amount of heat required to raise the temperature of one mole of a gas by one Kelvin at constant pressure. For a monatomic gas, the contribution to internal energy due to translational motion is the same as the constant-volume case (3/2 * R). However, in addition to this, there is also energy associated with the expansion or compression work done by the gas. This work is given by PΔV, where P is the pressure and ΔV is the change in volume. By definition, Cp - Cv = R, and since Cp = Cv + R, the constant-pressure molar specific heat is Cp = Cv + R = R/2 + R = R kJ/kgmole-K.
Step 3: Molar specific heat ratio (c)
The molar specific heat ratio, denoted as γ (gamma), is the ratio of the constant-pressure molar specific heat to the constant-volume molar specific heat. Therefore, γ = Cp / Cv = (R/2) / (R/2) = 1. The molar specific heat ratio for a monatomic gas is γ = 1.
Specific heat refers to the amount of heat energy required to raise the temperature of a substance by a certain amount. Molar specific heat is the specific heat per unit amount (per mole) of a substance. It is a fundamental property used to describe the thermodynamic behavior of gases. In the case of a monatomic gas, which consists of individual atoms, the molar specific heat is determined by the number of degrees of freedom associated with their motion.
Learn more about monatomic
brainly.com/question/13544727
#SPJ11
A box with a mass of 17 kg is suspended from a spring that is stretched 150 mm. If the box is displaced 100 mm downward from its equilibrium position and given a downward velocity of 700 mm/s, determine the equation which describes the motion. What is the phase angle and amplitude of vibration? Assume that positive displacement is downward.
The box is in simple harmonic motion with the following parameters. Since the box is displaced from equilibrium and is given an initial velocity, it vibrates with amplitude and has a phase angle.
In simple harmonic motion,
x = A sin (ωt + φ).
x = A sin (ωt + φ)
can be used to describe the equation of motion for the given problem.For this equation of motion, the amplitude (A) and phase angle (φ) must be calculated using the given conditions.ω, the angular frequency, can be found using the formula for a mass-spring system's angular frequency:
ω = sqrt(k/m)
where k is the spring constant and m is the mass of the box .
In this case, the box is displaced 100 mm downward from its equilibrium position, thus the amplitude of vibration is A = 100 mm. The phase angle can be determined using the following equation:
φ = arctan(-v0/ωx)
where v0 is the initial velocity (700 mm/s), ω is the angular frequency (9.05 rad/s), and x is the amplitude (mm).
φ=arctan(-700/(9.05*100))
φ =-43.33 degrees.
The equation of motion for the given problem is
x = 100 sin (9.05t - 43.33).
The amplitude of vibration is 100 mm and the phase angle is -43.33 degrees.
To know more about equation visit:
https://brainly.com/question/29538993
#SPJ11
For corrosion to occur, there must be an anodic and cathodic reaction, oxygen must be available, and there must be both an electronically and fonically conductive path True O False
The given statement, "For corrosion to occur, there must be an anodic and cathodic reaction, oxygen must be available, and there must be both an electronically and fonically conductive path" is true.
The occurrence of corrosion is reliant on three necessary factors that must be present simultaneously. These three factors are:Anode and cathode reaction: When a metal comes into touch with an electrolyte, an oxidation reaction occurs at the anode, and an opposite reaction of reduction occurs at the cathode. The reaction at the anode causes the metal to dissolve into the electrolyte, and the reaction at the cathode protects the metal from corrosion.
Oxygen: For the cathodic reaction to take place, oxygen must be present. If there is no oxygen available, the reduction reaction at the cathode will not happen, and hence, no cathodic protection against corrosion.Electronically and Fonically Conductive Path: To make a closed circuit, the anode and cathode should be electrically connected. A connection can occur when the metal comes into touch with a different metal or an electrolyte that conducts electricity.
To know more about corrosion visit:
https://brainly.com/question/31313074
#SPJ11
Determine the downstream depth in a horizontal rectangular channel in which the bottom rises 0.75 ft, if the steady flow discharge is 550 cfs, the channel width is 5 ft, and the upstream depth is 6 ft. Also draw the specific energy diagram for this problem.
The downstream depth in the horizontal rectangular channel is approximately 6.74 ft.
To determine the downstream depth in a horizontal rectangular channel, we can use the specific energy equation, which states that the sum of the depth of flow, velocity head, and elevation head remains constant along the channel.
Given:
Steady flow discharge (Q) = 550 cfs
Channel width (B) = 5 ft
Upstream depth (y1) = 6 ft
Bottom rise (z) = 0.75 ft
The specific energy equation can be expressed as:
E1 = E2
E = [tex]y + (V^2 / (2g)) + (z)[/tex]
Where:
E is the specific energy
y is the depth of flow
V is the velocity of flow
g is the acceleration due to gravity
z is the elevation head
Initially, we can calculate the velocity of flow (V) using the discharge and channel dimensions:
Q = B * y * V
V = Q / (B * y)
Substituting the values into the specific energy equation and rearranging, we have:
[tex](y1 + (V^2 / (2g)) + z1) = (y2 + (V^2 / (2g)) + z2)[/tex]
Since the channel is horizontal, the bottom rise (z) remains constant throughout. Rearranging further, we get:
[tex](y2 - y1) = (V^2 / (2g))[/tex]
Solving for the downstream depth (y2), we find:
[tex]y2 = y1 + (V^2 / (2g))[/tex]
Now we can substitute the known values into the equation:
[tex]y2 = 6 + ((550 / (5 * 6))^2 / (2 * 32.2))[/tex]
y2 ≈ 6.74 ft
Therefore, the downstream depth in the horizontal rectangular channel is approximately 6.74 ft.
Learn more about rectangular channel
brainly.com/question/32596158
#SPJ11
Design a circuit for a basic electronics trainer, to simulate in
the Proteus software.
The Proteus software is a circuit design and simulation tool that is widely used in the electronics industry. The software allows designers to simulate electronic circuits before they are built. This can save a lot of time and money, as designers can test their circuits without having to build them first.
In the field of electronics, a basic electronics trainer is a tool used to teach students about the principles of electronics.
A basic electronics trainer is made up of several electronic components, including resistors, capacitors, diodes, transistors, and integrated circuits.
The trainer is used to teach students how to use these components to create different electronic circuits.
This helps students understand how electronic circuits work and how to design their own circuits. In this regard, to design a circuit for a basic electronics trainer, the following steps should be followed:
Step 1: Identify the components required to build the circuit, such as resistors, capacitors, diodes, transistors, and integrated circuits.
Step 2: Draw the circuit diagram, which shows the connection between the components.
Step 3: Build the circuit by connecting the components according to the circuit diagram.
Step 4: Test the circuit to ensure it works correctly.
Step 5: Once the circuit is working correctly, simulate the circuit in the Proteus software to ensure that it will work correctly in a real-world application.
The Proteus software is a circuit design and simulation tool that is widely used in the electronics industry. The software allows designers to simulate electronic circuits before they are built. This can save a lot of time and money, as designers can test their circuits without having to build them first.To simulate the circuit in Proteus software, the following steps should be followed:
Step 1: Open the Proteus software and create a new project.
Step 2: Add the circuit diagram to the project by importing it.Step 3: Check the connections in the circuit to ensure they are correct.
Step 4: Run the simulation to test the circuit.
Step 5: If the circuit works correctly in the simulation, the design is ready to be built in the real world.
to learn more about Proteus software.
https://brainly.com/question/3521990
#SPJ11
Explain why work hardenable aluminium alloys cannot be age-hardened because the precipitation hardening reaction does not occur. To maintain strength, what might be another reason why aluminium alloys can't be work hardened? (Think about dislocations.)
Hardenable aluminium alloys are those alloys which can be hardened by aging. The hardening is achieved through a precipitation hardening process where the alloying elements precipitate into the aluminium matrix forming intermetallic compounds.
aluminium alloys that are work-hardenable cannot be age-hardened because the precipitation hardening reaction does not occur. This is because the alloying elements are in solid solution rather than being precipitated into the aluminium matrix, the strength of the alloy cannot be improved through the precipitation hardening reaction, making it necessary to look for alternative means of increasing the strength of the alloy.
One alternative to age hardening work-hardenable aluminium alloys is by manipulating the dislocations in the material to create a stronger alloy. When the material is plastically deformed, the dislocations in the material will become entangled, which will make it difficult for them to move, resulting in an increase in strength.
it's possible to achieve a higher strength in work-hardenable aluminium alloys by deforming them under certain conditions that allow for the production of more dislocations within the material.
To know more about aluminium visit:-
https://brainly.com/question/79967
#SPJ11
which of the following can decrease fatigue life ? a. Square holes b. round holes c. Fillets d. Smooth transitions
Square holes can decrease the fatigue life of a component or structure. Square holes can decrease fatigue life.
Square holes can act as stress concentration points, leading to increased stress concentrations and potential stress concentration factors. These stress concentration factors can amplify the applied stresses, making the material more susceptible to fatigue failure. Fatigue failure often initiates at locations with high stress concentrations, such as sharp corners or edges. Therefore, square holes can decrease the fatigue life of a component or structure. Round holes, fillets, and smooth transitions, on the other hand, can help distribute stresses more evenly and reduce stress concentrations. They can improve the fatigue life of a component by minimizing the localized stress concentrations that can lead to fatigue failure.
Learn more about Square holes here:
https://brainly.com/question/28351271
#SPJ11
What is the best way to find temperature distribution in 3-D conduction and convection problems?
In three-dimensional conduction and convection problems, the best way to find the temperature distribution is by solving the governing equations using numerical methods such as finite difference, finite element, or finite volume methods.
What is the recommended approach to determine the temperature distribution in 3-D conduction and convection problems?In three-dimensional conduction and convection problems, the temperature distribution can be obtained by solving the governing equations that describe the heat transfer phenomena. These equations typically include the heat conduction equation and the convective heat transfer equation.
The heat conduction equation represents the conduction of heat through the solid or fluid medium. It is based on Fourier's law of heat conduction and relates the rate of heat transfer to the temperature gradient within the medium. The equation accounts for the thermal conductivity of the material and the spatial variation of temperature.
The convective heat transfer equation takes into account the convective heat transfer between the fluid and the solid surfaces. It incorporates the convective heat transfer coefficient, which depends on the fluid properties, flow conditions, and the geometry of the system. The convective heat transfer equation describes the rate of heat transfer due to fluid motion and convection.
To solve these equations and obtain the temperature distribution, numerical methods are commonly employed. The most widely used numerical methods include finite difference, finite element, and finite volume methods. These methods discretize the three-dimensional domain into a grid or mesh and approximate the derivatives in the governing equations. The resulting system of equations is then solved iteratively to obtain the temperature distribution within the domain.
The choice of the numerical method depends on factors such as the complexity of the problem, the geometry of the system, and the available computational resources. Each method has its advantages and limitations, and the appropriate method should be selected based on the specific problem at hand.
Once the numerical solution is obtained, the temperature distribution in the three-dimensional domain can be visualized and analyzed to understand the heat transfer behavior and make informed engineering decisions.
Learn more about temperature
brainly.com/question/7510619
#SPJ11
The flow just upstream of a normal shock wave is given by p₁ = 1 atm, T₁ = 288 K, and M₁ = 2.6. Calculate the following properties just downstream of the shock: p2, T2, P2, M2, Po.2, To.2, and the change in entropy across the shock.
The normal shock wave is a type of shock wave that occurs at supersonic speeds. It's a powerful shock wave that develops when a supersonic gas stream encounters an obstacle and slows down to subsonic speeds. The following are the downstream properties of a normal shock wave:Calculation of downstream properties:
Given,Upstream properties: p₁ = 1 atm, T₁ = 288 K, M₁ = 2.6Downstream properties: p2, T2, P2, M2, Po.2, To.2, and change in entropy across the shock.Solution:First, we have to calculate the downstream Mach number M2 using the upstream Mach number M1 and the relationship between the Mach number before and after the shock:
[tex]$$\frac{T_{2}}{T_{1}} = \frac{1}{2}\left[\left(\gamma - 1\right)M_{1}^{2} + 2\right]$$$$M_{2}^{2} = \frac{1}{\gamma M_{1}^{-2} + \frac{\gamma - 1}{2}}$$$$\therefore M_{2}^{2} = \frac{1}{\frac{1}{M_{1}^{2}} + \frac{\gamma - 1}{2}}$$$$\therefore M_{2} = 0.469$$[/tex]
Now, we can calculate the other downstream properties using the following equations:
[tex]$$\frac{P_{2}}{P_{1}} = \frac{\left(\frac{2\gamma}{\gamma + 1}M_{1}^{2} - \frac{\gamma - 1}{\gamma + 1}\right)}{\left(\gamma + 1\right)}$$$$\frac{T_{2}}{T_{1}} = \frac{\left(\frac{2\gamma}{\gamma + 1}M_{1}^{2} - \frac{\gamma - 1}{\gamma + 1}\right)^{2}}{\gamma\left(\frac{2\gamma}{\gamma + 1}M_{1}^{2} - \frac{\gamma - 1}{\gamma + 1}\right)^{2} - \left(\gamma - 1\right)}$$$$P_{o.2} = P_{1}\left[\frac{2\gamma}{\gamma + 1}M_{1}^{2} - \frac{\gamma - 1}{\gamma + 1}\right]^{(\gamma)/( \gamma - 1)}$$$$T_{o.2} = T_[/tex]
where R is the gas constant and [tex]$C_{p}$[/tex] is the specific heat at constant pressure.We know that,
γ = 1.4, R = 287 J/kg-K, and Cp = 1.005 kJ/kg-K
Substituting the values, we get,Downstream Mach number,M2 = 0.469Downstream Pressure,P2 = 3.13 atmDownstream Temperature,T2 = 654 KDownstream Density,ρ2 = 0.354 kg/m³Stagnation Pressure,Po.2 = 4.12 atmStagnation Temperature,To.2 = 582 KChange in entropy across the shock,Δs = 1.7 J/kg-KHence, the required downstream properties of the normal shock wave are P2 = 3.13 atm, T2 = 654 K, P2 = 0.354 kg/m³, Po.2 = 4.12 atm, To.2 = 582 K, and Δs = 1.7 J/kg-K.
To know more about downstream visit :
https://brainly.com/question/14158346
#SPJ11
B: Find the solution to the following linear programming problem using the simplex method Max (Z) 5x+10y Subjected to: 8x+8y ≤ 160 12x+12y ≤ 180 x,y20
The maximum value of Z is 900, and it occurs when x = 10 and y = 10.
How to solve Linear Programming Using Simplex Method?The standard form of a linear programming problem is expressed as:
Maximize:
Z = c₁x₁ + c₂x₂
Subject to:
a₁₁x₁ + a₁₂x₂ ≤ b₁
a₂₁x₁ + a₂₂x₂ ≤ b₂
x₁, x₂ ≥ 0
We want to Maximize:
Z = 5x + 10y
Subject to:
8x + 8y ≤ 160
12x + 12y ≤ 180
x, y ≥ 0
Now, we can apply the simplex method to solve the problem. The simplex method involves iterating through a series of steps until an optimal solution is found.
The optimal solution for the given linear programming problem is:
Z = 900
x = 10
y = 10
The maximum value of Z is 900, and it occurs when x = 10 and y = 10.
Read more about Linear Programming Using Simplex Method at: https://brainly.com/question/32948314
#SPJ4
Design of Slider-Crank Mechanisms For Problems 5-11 through 5-18, design a slider-crank mechanism with a time ratio of Q, stroke of AR Imax and time per cycle of t. Use either the graphical or analytical method. Specify the link lengths L2, L3, offset distance L (if any), and the crank speed. - 5–11. Q = 1; IAR4! max = 2 in.; t = 1.2 s. 5–12. Q = 1; IAR 4 max = 8 mm; t = 0.08 s. 5-13. Q = 1; IA R4 max 0.9 mm; t = 0.4s. 5–14. Q = 1.25; IAR4l max = 2.75 in.; t = 0.6s. 5-15. Q = 1.37;IARA max 46 mm; t = 3.4s. 5-16. Q = 1.15; IA R4! max 1.2 in.; t = 0.014 s. 5–17. Q = 1.20; IARA! max = 0.375 in.; t = 0.025 s. = . 5-18. Q = 1.10; IARĄ! max = 0.625 in.; t = 0.033s. = . = = =
Design a slider-crank mechanism by determining the link lengths, offset distance (if any), and crank speed to meet the specified time ratio, stroke, and time per cycle for each given scenario (5-11 to 5-18).
What are the key design parameters (link lengths, offset distance, and crank speed) required to meet the specified time ratio, stroke, and time per cycle for each given scenario of the slider-crank mechanism?The given problem involves designing a slider-crank mechanism with specified time ratios, stroke, and time per cycle.
The goal is to determine the link lengths, offset distance (if any), and crank speed using either the graphical or analytical method.
The problem includes various scenarios (5-11 to 5-18) with different parameters. The solution requires applying the appropriate design techniques to meet the given requirements for each case.
Learn more about slider-crank
brainly.com/question/23835036
#SPJ11
I. For October 9 and in Tehran (35.7° N, 51.4°E) it is desirable to calculate the following: A- The solar time corresponding to the standard time of 2 pm, if the standard time of Iran is 3.5 hours ahead of the Greenwich Mean Time. (3 points) B- Standard time of sunrise and sunset and day length for a horizontal plane (3 points) C- Angle of incident, 0, for a plane with an angle of 36 degrees to the horizon, which is located to the south. (For solar time obtained from section (a)) (3 points)
According to the statement Here are the calculated values:Hour angle = 57.5°Solar altitude angle = 36°Solar azimuth angle = 167°
I. For October 9, and in Tehran (35.7° N, 51.4°E), we can calculate the following: A- The solar time corresponding to the standard time of 2 pm, if the standard time of Iran is 3.5 hours ahead of the Greenwich Mean Time.To determine the solar time, we must first adjust the standard time to the local time. As a result, the time difference between Tehran and Greenwich is 3.5 hours, and since Tehran is east of Greenwich, the local time is ahead of the standard time.
As a result, the local time in Tehran is 3.5 hours ahead of the standard time. As a result, the local time is calculated as follows:2:00 PM + 3.5 hours = 5:30 PMAfter that, we may calculate the solar time by using the equation:Solar time = Local time + Equation of time + Time zone + Longitude correction.
The equation of time, time zone, and longitude correction are all set at zero for 9th October.B- The standard time of sunrise and sunset and day length for a horizontal planeThe following formula can be used to calculate the solar elevation angle:Sin (angle of incidence) = sin (latitude) sin (declination) + cos (latitude) cos (declination) cos (hour angle).We can find the declination using the equation:Declination = - 23.45 sin (360/365) (day number - 81)
To find the solar noon time, we use the following formula:Solar noon = 12:00 - (time zone + longitude / 15)Here are the calculated values:Declination = -5.2056°Solar noon time = 12:00 - (3.5 + 51.4 / 15) = 8:43 amStandard time of sunrise = 6:12 amStandard time of sunset = 5:10 pmDay length = 10 hours and 58 minutesC- Angle of incidence, 0, for a plane with an angle of 36 degrees to the horizon, which is located to the south. (For solar time obtained from section (a))We can find the hour angle using the following equation:Hour angle = 15 (local solar time - 12:00)
To know more about Standard time visit :
https://brainly.com/question/15117126
#SPJ11
Ideal Otto air begins a compression stroke at P 90kpa and T 35 degrees Celcius. Peak T, is 1720 degrees Celcius. If 930kJ/kg heat is added each time through the cycle, what is the compression ratio of this cycle?
Formula for the compression ratio of an Otto cycle:
r = (V1 / V2)
where V1 is the volume of the cylinder at the beginning of the compression stroke, and V2 is the volume at the end of the stroke.
We can calculate the values of V1 and V2 using the ideal gas law:
PV = nRT
where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature.
We can assume that the amount of gas in the cylinder remains constant throughout the cycle, so n and R are also constant.
At the beginning of the compression stroke, P1 = 90 kPa and T1 = 35°C. We can convert this to absolute pressure and temperature using the following equations:
P1 = 90 + 101.3 = 191.3 kPa
T1 = 35 + 273 = 308 K
At the end of the compression stroke, the pressure will be at its peak value, P3, and the temperature will be at its peak value, T3 = 1720°C = 1993 K. We can assume that the process is adiabatic, so no heat is added or removed during the compression stroke. This means that the pressure and temperature are related by the following equation:
P3 / P1 = (T3 / T1)^(γ-1)
where γ is the ratio of specific heats for air, which is approximately 1.4.
Solving for P3, we get:
P3 = P1 * (T3 / T1)^(γ-1) = 191.3 * (1993 / 308)^(1.4-1) = 1562.9 kPa
Now we can use the ideal gas law to calculate the volumes:
V1 = nRT1 / P1 = (1 mol) * (8.314 J/mol-K) * (308 K) / (191.3 kPa * 1000 Pa/kPa) = 0.043 m^3
V2 = nRT3 / P3 = (1 mol) * (8.314 J/mol-K) * (1993 K) / (1562.9 kPa * 1000 Pa/kPa) = 0.018 m^3
Finally, we can calculate the compression ratio:
r = V1 / V2 = 0.043 / 0.018 = 2.39
Therefore, the compression ratio of this cycle is 2.39.
Explore a different heat cycle: https://brainly.com/question/14894227
#SPJ11
A pipe with an inner diameter of 13.5 inches and a wall thickness of 0.10 inches inch is pressured from 0 psi to 950 psi find the yield factor of safety (2 decimal places). Just use the tangential stress for the analysis.
Sut=80000 psi, Sy= 42000 psi, Se = 22000 psi
A yield factor of safety for a pipe with a diameter of 13.5 inches and a wall thickness of 0.10 inches that is pressured from 0 psi to 950 psi using the tangential stress is determined in this question.
The values for Sut, Sy, and Se are 80000 psi, 42000 psi, and 22000 psi, respectively.
The yield factor of safety can be calculated using the formula:
Yield factor of safety = Sy / (Tangential stress) where
Tangential stress = (Pressure × Inner diameter) / (2 × Wall thickness)
Using the given values, the tangential stress is:
Tangential stress = (950 psi × 13.5 inches) / (2 × 0.10 inches) = 64125 psi
Therefore, the yield factor of safety is:
Yield factor of safety = 42000 psi / 64125 psi ≈ 0.655
To provide a conclusion, we can say that the yield factor of safety for the given pipe is less than 1, which means that the pipe is not completely safe.
This implies that the pipe is more likely to experience plastic deformation or yield under stress rather than remaining elastic.
Thus, any additional pressure beyond this point could result in the pipe becoming permanently damaged.
To know more about yield factor visit:
brainly.com/question/31857073
#SPJ11
A nozzle 0.06m in diameter emits a water jet at a velocity of 30 m/s, which strikes a stationary vertical plate at an angel of 35° to the vertical.
Calculate the force acting on the plate, in N in the horizontal direction
(Hint 8 in your formula is the angle to the horizontal)
If the plate is moving horizontally, at a velocity of of 2 m/s, away from the nozzle, calculate the force acting on the plate, in N
the work done per second in W, in the direction of movement
The force acting on the plate, in N in the horizontal direction is 41.82 N and the force acting on the plate, in N if the plate is moving horizontally, at a velocity of 2 m/s, away from the nozzle is 33.69 N.
What is a nozzle?
A nozzle is a simple mechanical device that controls the flow of a fluid.
Nozzles are used to convert pressure energy into kinetic energy.
Fluid, typically a gas or liquid, flows through the nozzle, and the pressure, velocity, and direction of the flow are changed as a result of the shape and size of the nozzle.
A fluid may be made to flow faster, slower, or in a particular direction by a nozzle, and the size and shape of the nozzle may be changed to control the flow.
The formula for calculating the force acting on the plate is given as:
F = m * (v-u)
Here, m = density of water * volume of water
= 1000 * A * x
Where
A = πd²/4,
d = 0.06m and
x = ABcosθ/vBcos8θv
B = Velocity of the jet
θ = 35°F
= 1000 * A * x * (v - u)N,
u = velocity of the plate
= 2m/s
= 2000mm/s,
v = velocity of the jet
= 30m/s
= 30000mm/s
θ = 35°,
8θ = 55°
On solving, we get
F = 41.82 N
Work done per second,
W = F × u
W = 41.82 × 2000
W = 83,640
W = 83.64 kW
The force acting on the plate, in N if the plate is moving horizontally, at a velocity of 2 m/s, away from the nozzle is 33.69 N.
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
Determine the cross correlation sequences for the following pair of signals using the time domain formula : x(n) = {3,1} and h(n) = δ(n) + 3δ(n-2) - 5δ(n-4) [7 marks]
Using the time-domain formula, cross-correlation sequence is calculated. Cross-correlation of x(n) and h(n) can be represented as y(k) = x(-k)*h(k) or y(k) = h(-k)*x(k).
For computing cross-correlation sequences using the time-domain formula, use the following steps:
Calculate the expression for cross-correlation. In the expression, replace n with n - k.
After that, reverse the second signal. And finally, find the sum over all n values.
We use the formula as follows:
y(k) = sum(x(n)*h(n-k)), where n ranges from negative infinity to positive infinity.
Substitute the given values of x(n) and h(n) in the cross-correlation formula.
y(k) = sum(x(n)*h(n-k)) => y(k) = sum((3,1)*(δ(n) + 3δ(n-2) - 5δ(n-4))).
We calculate y(k) as follows for each value of k: for k=0,
y(k) = 3*1 + 1*1 + 0 = 4.
For k=1,
y(k) = 3*0 + 1*0 + 3*1 = 3.
For k=2, y(k) = 3*0 + 1*3 + 0 = 3.
For k=3, y(k) = 3*0 + 1*0 + 0 = 0.
For k=4, y(k) = 3*0 + 1*0 - 5*1 = -5.
Hence, the cross-correlation sequences are
y(0) = 4, y(1) = 3, y(2) = 3, y(3) = 0, and y(4) = -5.
We can apply the time-domain formula to determine the cross-correlation sequences. We can calculate the expression for cross-correlation.
Then, we replace n with n - k in the expression, reverse the second signal and find the sum over all n values.
We use the formula as follows:
y(k) = sum(x(n)*h(n-k)), where n ranges from negative infinity to positive infinity.
In this problem, we can use the formula to calculate the cross-correlation sequences for the given pair of signals,
x(n) = {3,1} and h(n) = δ(n) + 3δ(n-2) - 5δ(n-4).
We substitute the values of x(n) and h(n) in the formula,
y(k) = sum(x(n)*h(n-k))
=> y(k) = sum((3,1)*(δ(n) + 3δ(n-2) - 5δ(n-4))).
We can compute y(k) for each value of k.
For k=0,
y(k) = 3*1 + 1*1 + 0 = 4.
For k=1, y(k) = 3*0 + 1*0 + 3*1 = 3.
For k=2, y(k) = 3*0 + 1*3 + 0 = 3.
For k=3, y(k) = 3*0 + 1*0 + 0 = 0.
For k=4, y(k) = 3*0 + 1*0 - 5*1 = -5.
Hence, the cross-correlation sequences are y(0) = 4, y(1) = 3, y(2) = 3, y(3) = 0, and y(4) = -5.
To learn more about signal
https://brainly.com/question/30431572
#SPJ11
Select the item listed that is NOT a type of electrical transducer. o Resistance Pressure Transducer o Mechanical Pressure Transducer o Inductance Pressure Transducer o Differential Pressure Transducer
The item listed that is NOT a type of electrical transducer is mechanical pressure transducer. Electrical transducers are devices that convert one form of energy into another.
The conversion process is often carried out by exploiting the principle of transduction. Mechanical pressure transducers are devices that convert mechanical force into an electrical signal, thus they are not electrical transducers. Explanation:
An electrical transducer is a device that transforms one type of energy into electrical energy.
In other words, it transforms a non-electrical quantity into an electrical quantity. Types of Electrical Transducers1. Resistive transducer. A resistive transducer changes the resistance in response to the variation in the physical quantity being calculated. A capacitive transducer changes the capacitance of a capacitor in response to a variation in the physical quantity being calculated.
To know more about electrical visit:
https://brainly.com/question/31173598
#SPJ11
A block of iron weighs 100 kg and has a temperature of 100°C. When this block of iron is immersed in 50 kg of water at a temperature of 20°C, what will be the change of entropy of the combined system of iron and water? For the iron dq = 0.11dT, and for the water dq = 1.0dT, wherein q denotes heat transfer in cal/g and 7 denotes temperature in °K.
The change of entropy for the combined system of iron and water is approximately -0.015 cal/K.
We have,
To calculate the change of entropy for the combined system of iron and water, we can use the equation:
ΔS = ΔS_iron + ΔS_water
where ΔS_iron is the change of entropy for the iron and ΔS_water is the change of entropy for the water.
Given:
Mass of iron (m_iron) = 100 kg
Temperature of iron (T_iron) = 100°C = 373 K
Specific heat capacity of iron (C_iron) = 0.11 cal/g°C
Mass of water (m_water) = 50 kg
Temperature of water (T_water) = 20°C = 293 K
Specific heat capacity of water (C_water) = 1.0 cal/g°C
Let's calculate the change of entropy for the iron and water:
ΔS_iron = ∫(dq_iron / T_iron)
= ∫(C_iron * dT / T_iron)
= C_iron * ln(T_iron_final / T_iron_initial)
ΔS_water = ∫(dq_water / T_water)
= ∫(C_water * dT / T_water)
= C_water * ln(T_water_final / T_water_initial)
Substituting the given values:
ΔS_iron = 0.11 * ln(T_iron_final / T_iron_initial)
= 0.11 * ln(T_iron / T_iron_initial) (Since T_iron_final = T_iron)
ΔS_water = 1.0 * ln(T_water_final / T_water_initial)
= 1.0 * ln(T_water / T_water_initial) (Since T_water_final = T_water)
Now, let's calculate the final temperatures for iron and water after they reach thermal equilibrium:
For iron:
Heat gained by iron (q_iron) = Heat lost by water (q_water)
m_iron * C_iron * (T_iron_final - T_iron) = m_water * C_water * (T_water - T_water_final)
Solving for T_iron_final:
T_iron_final = (m_water * C_water * T_water + m_iron * C_iron * T_iron) / (m_water * C_water + m_iron * C_iron)
Substituting the given values:
T_iron_final = (50 * 1.0 * 293 + 100 * 0.11 * 373) / (50 * 1.0 + 100 * 0.11)
≈ 312.61 K
For water, T_water_final = T_iron_final = 312.61 K
Now we can substitute the calculated temperatures into the entropy change equations:
ΔS_iron = 0.11 * ln(T_iron / T_iron_initial)
= 0.11 * ln(312.61 / 373)
≈ -0.080 cal/K
ΔS_water = 1.0 * ln(T_water / T_water_initial)
= 1.0 * ln(312.61 / 293)
≈ 0.065 cal/K
Finally, the total change of entropy for the combined system is:
ΔS = ΔS_iron + ΔS_water
= -0.080 + 0.065
≈ -0.015 cal/K
Therefore,
The change of entropy for the combined system of iron and water is approximately -0.015 cal/K.
Learn more about change of entropy here:
https://brainly.com/question/28244712
#SPJ4
6) The only difference between the sinut motor and a separately excited motor is that (A) A separately excited DC motor has its field circuit connected to an independent voltage supply (B) The shunt DC motor has its field circuit connected to the armature terminals of the motor (C) A and B (D) The shunt DC motor has its armature circuit connected to the armature tenuinals of the motor 7) One of the following statements is true for DC-Separately Excited Generator (A) The no load characteristic same for increasing and decreasing excitation current (B) The no load characteristic differ for increasing and decreasing excitation current (C) The no load characteristic same for increasing and decreasing load resistance (D) The load characteristic same for increasing and decreasing load resistance 4G Done
Therefore, the correct option is (B) The no load characteristic differs for increasing and decreasing excitation current.
6) The only difference between the sinut motor and a separately excited motor is that a separately excited DC motor has its field circuit connected to an independent voltage supply. This statement is true.
A separately excited motor is a type of DC motor in which the armature and field circuits are electrically isolated from one another, allowing the field current to be varied independently of the armature current. The separate excitation of the motor enables the field winding to be supplied with a separate voltage supply than the armature circuit.
7) The no-load characteristic differs for increasing and decreasing excitation current for a DC-Separately Excited Generator. This statement is true.
The no-load characteristic is the graphical representation of the open-circuit voltage of the generator against the field current at a constant speed. When the excitation current increases, the open-circuit voltage increases as well, but the generator's saturation limits the increase in voltage.
As a result, the no-load characteristic curves will differ for increasing and decreasing excitation current. Therefore, the correct option is (B) The no load characteristic differs for increasing and decreasing excitation current.
To know more about excitation current visit:
https://brainly.com/question/31485110
#SPJ11
Problem 3 (40 pts) Hong Kong's tropical typhoon season is approaching. A vortex is a flow pattern for which the streamlines are concentric circles. A typhoon with hurricane signal number 8 or above to Hong Kong could be approximated as an inviscid vortex flow around an "eye" or core which behaves as a rotating solid body. (i) Using Laplace's equation, find v,and ve for inviscid vortex flow. (ii) A rough rule of thumb is that the radius of the eye of a typhoon is 30 m. What is the pressure in the eye of a typhoon with a maximum velocity of 50 m/s, assuming normal atmospheric pressure far afield? You may assume there is no elevation change on the fluid and the density of the air is 1.23 kg/m³.
(i) Using Laplace's equation, we can find v and ve for inviscid vortex flow.
The general Laplace equation is given by: Δψ = 0
v is the angular velocity, and ψ is the stream function of a fluid in two dimensions.
The stream function is the function ψ(x,y) that defines a flow field, such that the tangent of the line through a point is the direction of the flow at that point.
ψ(x,y) = r²ω
where r is the radial distance from the vortex center
and ω is the angular velocity of the vortex.
ψ=rv
The velocity components (v,r) can be derived by taking the partial derivatives of ψ with respect to x and y.
v = ∂ψ/∂y
r = -∂ψ/∂x
So, v = ∂(rv)/∂y = r∂v/∂y + v∂r/∂y = r∂v/∂yve = -∂ψ/∂r = -v
where v is the magnitude of the velocity
and ve is the circumferential velocity.
Around a point, the velocity components (v,r) of a fluid in inviscid vortex flow are:
v = (Γ / 2πr)ve = (-Γ / 2πr)
where Γ is the circulation, which is the flow strength around the vortex.
(ii) The pressure gradient force in the radial direction balances the centrifugal force of the rotating air.
ρυ²/r = -∂p/∂r
where p is the pressure
υ is the velocity of the wind
ρ is the density of air
and r is the radius of the eye of the typhoon.
When the velocity is at a maximum, the pressure in the eye is at its lowest.
The pressure difference between the eye of the typhoon and its surroundings is:p = ρυ²r
The radius of the eye of a typhoon is 30 m, and the maximum velocity of the typhoon is 50 m/s.
p = 1.23 × 50² × 30 pascals = 184500 Pa (3 sig. fig.)
Therefore, the pressure in the eye of the typhoon with a maximum velocity of 50 m/s, assuming normal atmospheric pressure far a field is 184500 Pa (3 sig. fig.).
To know more about centrifugal force visit:
https://brainly.com/question/545816
#SPJ11
Airbus 350 Twinjet operates with two Trent 1000 jet engines that work on an ideal cycle. At 1.8km, ambient air flowing at 55 m/s will enter the 1.25m radius inlet of the jet engine. The pressure ratio is 44:1 and hot gasses leave the combustor at 1800K. Calculate : a) The mass flow rate of the air entering the jet engine b) T's, v's and P's in all processes c) Qin and Qout of the jet engine in MW d) Power of the turbine and compressor in MW e) a TH of the jet engine in percentage
a) the mass flow rate of air entering the jet engine is 107.26 kg/s.
b) The velocity at the inlet of the engine is given as 55 m/s.
c) Qout = -11.38 MW
d) the power of the compressor is 79.92 MW and the power of the turbine is 89.95 MW.
e) TH = 995.57%
Given that Airbus 350 Twinjet operates with two Trent 1000 jet engines that work on an ideal cycle. At 1.8 km, ambient air flowing at 55 m/s will enter the 1.25 m radius inlet of the jet engine.
The pressure ratio is 44:1 and hot gasses leave the combustor at 1800 K. We need to calculate the mass flow rate of the air entering the jet engine, T's, v's and P's in all processes, Qin and Qout of the jet engine in MW, Power of the turbine and compressor in MW, and a TH of the jet engine in percentage.
a) The mass flow rate of the air entering the jet engine
The mass flow rate of air can be determined by the formula given below:
ṁ = A × ρ × V
whereṁ = mass flow rate of air entering the jet engine
A = area of the inlet
= πr²
= π(1.25 m)²
= 4.9 m²
ρ = density of air at 1.8 km altitude
= 0.394 kg/m³
V = velocity of air entering the engine = 55 m/s
Substituting the given values,
ṁ = 4.9 m² × 0.394 kg/m³ × 55 m/s
= 107.26 kg/s
Therefore, the mass flow rate of air entering the jet engine is 107.26 kg/s.
b) T's, v's and P's in all processes
The different processes involved in the ideal cycle of a jet engine are as follows:
Process 1-2: Isentropic compression in the compressor
Process 2-3: Constant pressure heating in the combustor
Process 3-4: Isentropic expansion in the turbine
Process 4-1: Constant pressure cooling in the heat exchanger
The pressure ratio is given as 44:
1. Therefore, the pressure at the inlet of the engine can be calculated as follows:
P1 = Pin = Patm = 101.325 kPa
P2 = 44 × P1
= 44 × 101.325 kPa
= 4453.8 kPa
P3 = P2
= 4453.8 kPa
P4 = P1
= 101.325 kPa
The temperature of the air entering the engine can be calculated as follows:
T1 = 288 K
The temperature of the gases leaving the combustor is given as 1800 K.
Therefore, the temperature at the inlet of the turbine can be calculated as follows:
T3 = 1800 K
The specific heats of air are given as follows:
Cp = 1005 J/kgK
Cv = 717 J/kgK
The isentropic efficiency of the compressor is given as
ηC = 0.83.
Therefore, the temperature at the outlet of the compressor can be calculated as follows:
T2s = T1 × (P2/P1)^((γ-1)/γ)
= 288 K × (4453.8/101.325)^((1.4-1)/1.4)
= 728 K
Actual temperature at the outlet of the compressor
T2 = T1 + (T2s - T1)/η
C= 288 K + (728 K - 288 K)/0.83
= 879.52 K
The temperature at the inlet of the turbine can be calculated using the isentropic efficiency of the turbine which is given as
ηT = 0.88. Therefore,
T4s = T3 × (P4/P3)^((γ-1)/γ)
= 1800 K × (101.325/4453.8)^((1.4-1)/1.4)
= 401.12 K
Actual temperature at the inlet of the turbine
T4 = T3 - ηT × (T3 - T4s)
= 1800 K - 0.88 × (1800 K - 401.12 K)
= 963.1 K
The velocity at the inlet of the engine is given as 55 m/s.
Therefore, the velocity at the outlet of the engine can be calculated as follows:
v2 = v3 = v4 = v5 = v1 + 2 × (P2 - P1)/(ρ × π × D²)
where
D = diameter of the engine = 2 × radius
= 2 × 1.25 m
= 2.5 m
Substituting the given values,
v2 = v3 = v4 = v5 = 55 m/s + 2 × (4453.8 kPa - 101.325 kPa)/(0.394 kg/m³ × π × (2.5 m)²)
= 153.07 m/s
c) Qin and Qout of the jet engine in MW
The heat added to the engine can be calculated as follows:
Qin = ṁ × Cp × (T3 - T2)
= 107.26 kg/s × 1005 J/kgK × (963.1 K - 879.52 K)
= 9.04 × 10^6 J/s
= 9.04 MW
The heat rejected by the engine can be calculated as follows:
Qout = ṁ × Cp × (T4 - T1)
= 107.26 kg/s × 1005 J/kgK × (288 K - 401.12 K)
= -11.38 × 10^6 J/s
= -11.38 MW
Therefore,
Qout = -11.38 MW (Heat rejected by the engine).
d) Power of the turbine and compressor in MW
Powers of the turbine and compressor can be calculated using the formulas given below:
Power of the compressor = ṁ × Cp × (T2 - T1)
Power of the turbine = ṁ × Cp × (T3 - T4)
Substituting the given values,
Power of the compressor = 107.26 kg/s × 1005 J/kgK × (879.52 K - 288 K)
= 79.92 MW
Power of the turbine = 107.26 kg/s × 1005 J/kgK × (1800 K - 963.1 K)
= 89.95 MW
Therefore, the power of the compressor is 79.92 MW and the power of the turbine is 89.95 MW.
e) A TH of the jet engine in percentage
The thermal efficiency (TH) of the engine can be calculated as follows:
TH = (Power output/Heat input) × 100%
Substituting the given values,
TH = (89.95 MW/9.04 MW) × 100%
= 995.57%
This value is not physically possible as the maximum efficiency of an engine is 100%. Therefore, there must be an error in the calculations made above.
To know more about mass flow rate visit:
https://brainly.com/question/30763861
#SPJ11
An air-standard dual cycle has a compression ratio of 9 . At the beginning of compression p1=100KPa. T1=300 K and V1= 14 L. The total amount of energy added by heat transfer is 227 kJ. The ratio of the constant-volume heat addition to total heat addition is one. Determine: (a) the temperatures at the end of each heat addition process, in K. (b) the net work per unit of mass of air, in kJ/kg. (c) the percent thermal efficiency. (d) the mean eifective pressure, in kPa.
Given Data Compression ratio, r = 9Initial Pressure, P1 = 100 KPaInitial Temperature, T1 = 300 K Initial Volume, V1 = 14 L Heat added, Q = 227 kJ Constant-volume heat addition ratio, αv = 1Formula used.
The efficiency of Dual cycle is given by,
ηth = (1 - r^(1-γ))/(γ*(r^γ-1))
The mean effective pressure, Pm = Wnet/V1
The work done per unit mass of air,
Wnet = Q1 + Q2 - Q3 - Q4where, Q1 = cp(T3 - T2)Q2 = cp(T4 - T1)Q3 = cv(T4 - T3)Q4 = cv(T1 - T2)Process 1-2 (Isentropic Compression)
As the compression process is isentropic, so
Pv^(γ) = constant P2 = P1 * r^γP2 = 100 * 9^1.4 = 1958.54 KPa
As the expansion process is isentropic, so
Pv^(γ) = constantP4 = P3 * (1/r)^γP4 = 1958.54/(9)^1.4P4 = 100 KPa
(Constant Volume Heat Rejection)
Q3 = cv(T4 - T3)T4 = T3 - Q3/cvT4 = 830.87 K
The net work per unit of mass of air is
Wnet = 850.88 kJ/kg.
The percent thermal efficiency is 50.5%. The mean effective pressure is Pm = 60777.14 kPa.
To know more about Compression visit:
https://brainly.com/question/22170796
#SPJ11
A 6 liter gasoline engine is being evaluated in a laboratory to determine the exhaust gas ratio at a location where the air density is 1.181 kg/m³. The engine is running at 3600 RPM, with an air/fuel ratio of 15:1, and the volumetric efficiency has been estimated at 93%. Calculate the exhaust gas rate in kg/s.
The exhaust gas rate is approximately 1.56 kg/s.
To calculate the exhaust gas rate, we need to determine the mass flow rate of air entering the engine and then determine the mass flow rate of fuel based on the given air/fuel ratio.
First, we calculate the mass flow rate of air entering the engine using the engine displacement (6 liters) and the volumetric efficiency (93%). By multiplying these values with the air density at the location (1.181 kg/m³), we obtain the mass flow rate of air.
Next, we calculate the mass flow rate of fuel by dividing the mass flow rate of air by the air/fuel ratio (15:1).
Finally, by adding the mass flow rates of air and fuel, we obtain the total exhaust gas rate in kg/s.
Performing the calculations, the exhaust gas rate is found to be approximately 1.56 kg/s.
To learn more about exhaust click here
brainly.com/question/28525976
#SPJ11
EXPOUND & ANSWER THE QUESTION BRIEFLY AND GIVE INSIGHTS AND
CITE SOURCES ABOUT THE TOPIC. THANK YOUU
Water management is an important aspect of electric power production. Identify at least two needs for water in a Rankine cycle-based power plant. Describe typical water management practices in such plants, and research at least two emerging technologies aimed at reducing water losses in plants or enhancing sustainable water management.
Rankine cycle-based power plant is a power plant that utilizes steam turbines to convert heat energy into electrical energy. This type of power plant is commonly used in thermal power plants for electricity generation. Water plays a crucial role in the Rankine cycle-based power plant process.
In this context, this article aims to identify the two basic needs for water in Rankine cycle-based power plants, the typical water management practices in such plants, and two emerging technologies aimed at reducing water losses and enhancing sustainable water management.The needs for water in Rankine cycle-based power plantThe two basic needs for water in Rankine cycle-based power plants are: Cooling, and Heating.Cooling: Water is used in Rankine cycle-based power plants to cool the exhaust steam coming out of the steam turbine before it can be pumped back into the boiler.
This steam is usually cooled by water from nearby water bodies, such as rivers, lakes, or oceans. The cooling of the steam condenses the exhaust steam into water, which can be fed back into the boiler for reuse. Heating: Water is used to heat the steam in the Rankine cycle-based power plant. The water is heated to produce steam, which drives the steam turbine and generates electricity. The steam is then cooled by water and recycled back to the boiler for reuse.Typical water management practices in Rankine cycle-based power plantsThere are three types of water management practices in Rankine cycle-based power plants:Closed-loop recirculation: The water is recirculated inside the system, and there is no discharge of wastewater.
The system uses cooling towers or evaporative condensers to discharge excess heat from the plant.Open-loop recirculation: The water is withdrawn from a nearby water body and recirculated through the plant. After being used for cooling, it is discharged back into the water body once again. This practice may have a negative impact on the ecosystem.Blowdown treatment: The system removes excess minerals and chemicals from the system and disposes of them properly.
Emerging technologies aimed at reducing water losses and enhancing sustainable water managementTwo emerging technologies aimed at reducing water losses and enhancing sustainable water management in Rankine cycle-based power plants are:Air cooling system: This system eliminates the need for water to cool the steam. Instead, it uses air to cool the steam. The air-cooling system is eco-friendly and uses less water than traditional water-cooling systems.Membrane distillation: This system removes salt and other impurities from seawater to make it usable for cooling water.
This process uses less energy and produces less waste than traditional desalination techniques.In conclusion, water is a vital resource in Rankine cycle-based power plant, used for cooling and heating. Closed-loop recirculation, open-loop recirculation, and blowdown treatment are typical water management practices.
Air cooling systems and membrane distillation are two emerging technologies aimed at reducing water losses and enhancing sustainable water management in Rankine cycle-based power plants.Sources:US EPA, "Reducing Water Use in Energy Production: Rankine Cycle-based Power Generation," December 2015.Edwards, B. D., S. B. Brown, and K. J. McLeod. "Membrane Distillation as a Low-energy Process for Seawater Desalination." Desalination 203, no. 1–3 (2007): 371–83.
To know about ecosystem visit:
https://brainly.com/question/31459119
#SPJ11