The heat transfer rate per unit area in a thermal circuit is equivalent to what quantity in an electric circuit? A. voltage B. current C. resistance D. inductance

Answers

Answer 1

Answer:

A. voltage

Explanation:

The rate of heat transfer per unit area in a thermal circuit is equivalent to the voltage in an electrical circuit.

This is because, within an electrical circuit the voltage is supplied by a generator, which can be batteries, batteries, or others. The moment the electrical voltage acts within a circuit, it will consist of the gradient of electrical potential between two points, which will cause the electrons to move from the point with the highest concentration to the point with the lowest concentration (similar to the transfer of heat from the thermal circuit) generating the electric current.


Related Questions

A company that produces footballs uses a proprietary mixture of ideal gases to inflate their footballs. If the temperature of 230 grams [g] of gas mixture in a 15-liter [L] tank is maintained at 465 degrees Rankine [°R] and the tank is pressurized to 135 pound-force per square inch [psi], what is the molecular weight of the gas mixture in units of grams per mole

Answers

Answer:

The molecular weight of the gas mixture is 35.38 g/mol.

Explanation:

The molecular weight of the gas can be found using the following equation:

[tex] M = \frac{m}{n} [/tex]

Where:

m: is the mass = 230 g

n: is the number of moles

First, we need to find the number of moles using Ideal Gas Law:

[tex] PV = nRT [/tex]

Where:

P: is the pressure = 135 psi

V: is the volume = 15 L

R: is the gas constant = 0.082 L*atm/(K*mol)

T: is the temperature = 465 °R (K = R*5/9)

[tex]n = \frac{PV}{RT} = \frac{135 psi*\frac{1 atm}{14.6959 psi}*15 L}{0.082 L*atm/(K*mol)*465*(5/9) K} = 6.50 moles[/tex]                

Finally, the molecular weight of the gas is:

[tex] M = \frac{m}{n} = \frac{230 g}{6.50 moles} = 35.38 g/mol [/tex]

Therefore, the molecular weight of the gas mixture is 35.38 g/mol.

I hope it helps you!

What are the main causes of injuries when using forklifts?

Answers

The forklift overturning is a very common way of getting injured from a forklift. Overturning the forklift means it tips over onto it's side due to the operator turning it too fast.

Two wooden members of uniform rectangular cross section are joined using a simple glued scarf splice. The maximum allowable shearing stress and maximum allowable normal stress in the glued splice is 50 MPa and 100 MPa, respectively. The cross-section area of the glued member is 400 mm2. (a) What should the value of the angle  be to achieve maximum load Fmax? (b) What is the magnitude of the maximum load Fmax?

Answers

Answer:

a). α =  26.57  

b). Maximum load is 50 .kN

Explanation:

a).

The normal force is given by

N = σ A cosec β

where, σ is the normal stress

            A is the cross sectional area

Similarly, shear force is given by

S= τ A cosec β

where, τ is the shearing stress

Now from the figure,

tan β = S/N

        = τ/σ

Therefore, [tex]$\beta = \tan^{-1}(2)$[/tex]  = 63.43

α = 90 - β = 26.57

b).

The normal force is given by

[tex]$N=(100\times 10^6)(400\times 10^{-6}) \text{ cosec}\ 63.43$[/tex]

[tex]$N=44.78\times 10^3$[/tex] N

We have

[tex]$\Sigma F_y=0$[/tex]

∴ N - F sin β = 0

⇒ F = N / sin β

      = [tex]$\frac{44.72\times 10^3}{\sin(63.43)} = 50\times 10^3 N$[/tex]

Similarly,

The shear force is given by

S = τ A cosec β

  = [tex]$(50\times 10^6)(400\times 10^{-6}) \text{ cosec}\ 63.43 = 22.36\times 10^3 N$[/tex]

[tex]$\Sigma F_x=0$[/tex]

∴ S - F cos β = 0

⇒ F = S / cos β

[tex]$\frac{22.36\times 10^3}{\cos(63.43)} = 49.99\times 10^3 N$[/tex]

Therefore, force is 50 kN.

parallel circuits???

Answers

PLEASE GIVE BRAINLIST

A parallel circuit has two or more paths for current to flow through. Voltage is the same across each component of the parallel circuit. The sum of the currents through each path is equal to the total current that flows from the source.

HOPE THIS HELPED

What is the period if the clock frequency is 3.5 GHz?

Answers

Answer:

Period = 0.2857 nanoseconds

Explanation:

We are told that frequency = 3.5 GHz

This is simply 3.5 × 10^(9) Hz

Now, from wave equations, Period is given by the formula;

Period = 1/frequency

Thus;

Period = 1/(3.5 × 10^(9))

Period = 0.2857 × 10^(-9) seconds

From conversions, we can simplify the answer.

1 second = 10^(-9) nanoseconds

Thus, 0.2857 × 10^(-9) seconds = 0.2857 × 10^(-9) × 10^(-9) nanoseconds = 0.2857 nanoseconds

12. You need to be at the lift controls whenever the lift is in motion A) True B)False

Answers

the answer to that would be a) true

A tensile test uses a test specimen that has a gage length of 50 mm and an area = 206 mm2. During the test, the specimen yields under a load of 97,944 N. The corresponding gage length = 50.2 mm - this is at the 0.2 percent yield point. The maximum load of 162,699 N is reached at a gage length = 63 mm. If fracture occurs at a gage length of 71 mm, determine the percent elongation in % - enter your answer as a whole number, not as a fraction.

Answers

Answer:

The percent elongation in the length of the specimen is 42%

Explanation:

Given that:

The gage length of the original test specimen  [tex]L_o[/tex] = 50 mm

The final gage length [tex]L_f[/tex] = 71 mm

The area = 206 mm²

maximum load  =  162,699 N

To determine the percent elongation in %, we use the formula:

[tex]\%EL = \dfrac{L_f-L_o}{L_o}\times 100[/tex]

[tex]\%EL = \dfrac{71 \ mm-50 \ mm}{50 \ mm}\times 100[/tex]

[tex]\%EL = \dfrac{21 mm}{50 \ mm}\times 100[/tex]

[tex]\%EL = 0.42 \times 100[/tex]

[tex]\mathbf{\%EL = 42 \%}[/tex]

The percent elongation in the length of the specimen is 42%

How can you safely lift and support a vehicle

Answers

Answer:

Place the jack under the part of the vehicle that it should contact when raised. If you're using jack stands, place them near the jack. If you place your jack incorrectly, you can injure your car. To find the proper place to position the jack for your particular vehicle, check your owner's manual.

A picture of a ____ is the label pictogram on a chemical that warms of a product's acute toxicity

Answers

Answer:skull and crossbones

Explanation:

Help me for this question

Answers

The answer is definitely c, your correct:) I hope you have a good day!!

- The four leading causes of death in the
construction industry include electrical
incidents, struck-by incidents, caught-in or
caught-between incidents, and
a. vehicular incidents
b. falls
C. radiation exposure
d. chemical burns

Answers

My best guess is b but I honestly don’t know

for high-volume production runs, machining parts from solid material might not be the best choice of manufacturing operations because

Answers

Answer:

There are actually multiple types of processes a manufacturer uses, and those can be grouped into four main categories: casting and molding, machining, joining, and shearing and forming.

Explanation:

how do you make coke for steel?

Answers

Can you be a bit more specific plz and that will let me identify the answer

Which statement demonstrates the most scientific observation?

Answers

Where are the statements to choose from

__________ use cleaning solutions that eventually become spent and must be disposed of properly


a sump pits
b car washers
c part washers
d tire cleaners

Answers

Answer:Part washers

Explanation:

I did it..

The only option that uses cleaning solutions that become spent and must be disposed properly is;

Option C; Parts Washers

To answer this question, let us examine each option;

Option A; Sump Pits; These are basins at the lowest part of specific areas designed to allow all water collected in that basin area to drain into it. This has no business with cleaning solution.

Option B; Car washers; These are like machine dryers used to clean the exterior and interior parts of motor vehicles.

Option C; Part Washers; These are mechanical devices that are designed for cleaning to remove debris, grime, oil dirt, paint, and other substances that could potentially cause contamination from parts in order to get them ready for assembling, packaging, or even coating. They are basically used to clean parts to get them ready for functional use.

Option D; Tire cleaner is just used to clean tire but is not something that becomes spent and should be disposed properly as it is more like a liquid.

The only correct option is Option C.

Read more at; https://brainly.com/question/25024807

Solve the compound inequality. 3x − 4 > 5 or 1 − 2x ≥ 7

Answers

x ≤ −3 or x > 3
inequality form

Wheel grinders need be equipped with an

Answers

Answer:

wheel guard

Explanation:

to protect our hands and reduce spark

Explain how engineering and science-related?

Answers

Answer:

While scientists study how nature works, engineers create new things, such as products, websites, environments, and experiences. Because engineers and scientists have different objectives, they follow different processes in their work.

Explanation:

1. Looking at the case study provided under the Companion Material section, what is the main problem that is addressed in this case study? Maintenance workers painted over the pipes. Engineers lost all of their work because of the flood. The water pipes broke and flooded the space center. There was no paperwork for the maintenance work done on the pipes.

Answers

Incomplete question. However, I provided information that could assist you in identifying the main problem or issue addressed in any case study.

Explanation:

First, note that a case study is simply a learning aid that allows one to learn from a real-life scenario.

To determine the main problems of a case study one needs to:

Read the case as many times as possible to become familiar with the message been expressed. For example, by highlighting or underlining the most important facts it can help you to discover the main problem or issue. Check for any facts provided in the case study, by so doing you can identify the most important problems.

Thus, by taking these few steps you may be able to determine the main problem in that case study.

What are materials engineers trying to discover when they study different materials? Whether or not materials corrode and oxidize how materials perform and deteriorate if certain materials have been used in the past and at which historical ages which metals conduct heat

Answers

Answer:

Material engineers study various materials to discover the reason and cause of its existence, the chemical properties, how long it has been there, and how it impacts human life.

Explanation:

Material engineer is an engineering discipline that focuses to improve human life by studying the environment and the various elements or materials it holds.

It uses the power of pure science to test and analysis its findings, documents its features and exposes them to the world. Materials like metals and other elemental forms were all tested by these engineers to determine its history and chemical and biological use.

Answer:

how materials perform and deteriorate

Explanation:

What are the common approximations made in the analysis of heat exchangers?

Answers

Answer: making sure that they are up to date

Explanation:

The displacement volume of an internal combustion engine is 3 liters. The processes within each cylinder of the engine are modeled as an air-standard Diesel cycle with a cutoff ratio of 2.5. The state of the air at the beginning of compression is fixed by P1=95kPa, T1=22oC, and V1 = 3.17 liters.
Determine the net work per cycle, in kJ, the power developed by the engine, in kW, and the thermal efficiency, if the cycle is executed 1000 times per min.

Answers

Answer:

1) The power developed by the engine is 14705.7739 kW

2) The thermal efficiency is approximately 61.5%

Explanation:

The given parameters are;

P₁ = 95 kPa

T₁ = 22°C

V₁ = 3.17 liters

The cutoff ratio = 2.5

Displacement volume = 3 liters

The number of times the cycle is executed per minute = 1000 times per minute

We have;

The displacement volume = V₁ - V₂ = 3 l

V₁ = 3.17 l

V₂ = 3 - 3.17 = 0.17 l

Compression ratio = V₁/V₂ = 3.17/0.17 ≈ 18.65

P₂/P₁ = P₂/(95 kPa) =  (V₁/V₂)^(k) = 18.65^1.4

P₂ = (95×18.65^(1.4)) ≈ 5710.5 kPa

T₂/T₁ = (V₁/V₂)^(k - 1)

T₂/(295 K)= (18.65)^(1.4 - 1)

T₂ = 295 * (18.65)^(1.4 - 1) = 950.81 K

The cutoff ratio = V₃/V₂ = 2.5

T₃ = T₂ × V₃/V₂  = 2.5 * 950.81 K = 2377.025 K

[tex]Q_{in}[/tex] = [tex]C_p[/tex]×(T₃ - T₂) = 1.006 × (2377.025 - 950.81) = 1,434.77 kJ/kg

T₄ = T₃ × (V₃/V₄)^(k-1) =

Therefore,

[tex]T_4 = T_3 \times \left (\dfrac{r_c}{r} \right )^{k - 1} = 2377.025 \times \left( \dfrac{2.5}{18.65} \right )^{1.4 - 1} \approx 1064 \ K[/tex]

T₄ ≈ 1064 K

[tex]Q_{out}[/tex] = [tex]-C_v \times (T_4 - T_1)[/tex]

[tex]C_v = C_p/k = 1.006/1.4 \approx 0.7186 \ kJ/kg[/tex]

∴ [tex]Q_{out}[/tex] = 0.7186×(1064 - 295) = 552.6034 kJ/kg

1) The net work = [tex]Q_{in}[/tex] - [tex]Q_{out}[/tex] = 1,434.77 kJ/kg - 552.6034 kJ/kg ≈ 882.17 kJ/kg

The number of cycle per minute = 1000 rpm

The number of cycle per minute = 1000 rpm/60 = 16.67 cycles per second

The power developed by the engine = The number of cycles per second × The net work of the engine

Therefore;

The power developed by the engine = 16.67 cycles/second  × 882.17 kJ/kg

The power developed by the engine = 14705.7739 kW

2) Efficiency, [tex]\eta _{th}[/tex], is given as follows;

[tex]\eta _{th} = \dfrac{Q_{in}-Q_{out}}{Q_{in}} \times 100 = 1 - \dfrac{Q_{out}}{Q_{in}} \times 100= 1 - \dfrac{552.6034}{1434.77}\times 100 \approx 61.5\%[/tex]

Therefore, the thermal efficiency ≈ 61.5%.

While out on the International Space Station, an engineer was able to gather a sample of a new type of unidentified rock. What knowledge will the engineer use to predict the potential of this new material?

Answers

Answer:

The engineer will conduct a variety of tests, including chemical, mechanical, electrical, and physical examinations, to determine the potential of the new material.

Explanation:

They will need to test the material, this will also help to determine its malleability.

Hope this helps!

To create an effective study schedule, a student must
guess the amount of time needed for studying.
O write down all activities and commitments.
O allow the same amount of time each day for studying.
O budget periods of time to study daily, even if it is interrupted.

Answers

Answer:

B) write down all activities and commitments.

Explanation:

also i found the answer on quizlet hope this works:))

Answer:

write down all activities and commitments.

Explanation:

i had got the same question on my unit test and it was the answer it was right

Which items are NOT found on a
door?*
5 points
Cladding
Moulding
Weatherstrip
Check Strap
Striker
All of the above
None of the above

Answers

Answer:

None of the above cause thats what i put

What is a specialized accreditation? A. evaluation of the quality of instruction B. evaluation of a particular program C. evaluation of students studying in an organization D. evaluation of recreational facilities in an organization

Answers

Answer:

B. evaluation of a particular program

Explanation:

Before students enrol into any given discipline, they should first ensure that their program of choice is well accredited. In a specific program, specialized accreditation has the function of telling would be students if the program meets up with academic standards in the field

Accreditation is a way of assessing faculty and curriculum quality of schools to make sure that they are up to academic standards and are also preparing students to future success in the field.

The production process of rods from machine "A" yields specimen with the following specs. Mean: µ(LA)=20.00mm, STD: s(LA)=0.50mm. You need to purchase new machine to increase the production capacity and accuracy together. If the new machine "B" will produce half of the total rods, what is the STD, s(LB), that needs to achieve the total STD, s(LT)=0.4mm? Assume Corr(A,B)=0.4

Answers

Answer: the standard deviation STD of machine B is s (Lb) = 0.4557

Explanation:

from the given data, machine A and machine B produce half of the rods

Lt = 0.5La + 0.5Lb

so

s² (Lt) = 0.5²s²(La) + 0.5²s²(Lb) + 0.5²(2)Cov (La, Lb)

but Cov (La, Lb) = Corr(La, Lb) s(La) s(Lb) = 0.4s (La) s(Lb)

so we substitute

s²(Lt) = 0.25s² (La) + 0.25s² (Lb) + 0.4s (La) s(Lb)

0.4² = 0.25 (0.5²) + 0.25s² (Lb) + (0.5)0.4(0.5) s(Lb)

0.64 = 0.25 + s²(Lb) + 0.4s(Lb)

s²(Lb) + 0.4s(Lb) - 0.39 = 0

s(Lb) = { -0.4 ± √(0.16 + (4*0.39)) } / 2

s (Lb) = 0.4557

therefore the standard deviation STD of machine B is s (Lb) = 0.4557

A sign that has a white background with a
green panel with white lettering is a
a. general information sign
b. safety instruction sign
c. caution sign
d. danger sign

Answers

Answer:

A

Explanation:

general information sign

safety is orange

caution is yellow

danger is red

I got u you are going to pass your class easy

You are designing an airplane to carry liquid cargo that will slosh and move side to side in its container. This could make the plane unstable. What type of airfoil would you use for the wing? Why. Answer in a full sentence or more

Answers

I wold use a flat bottom airfoil because I feel I will mack it mor stabilizes than others

Use the diagram to determine total resistance. (Round the FINAL answer to one decimal place.) Note: Use the rated voltage and wattage to determine resistance. Note: Ra and Rb represent the resistance of the wire. The 120 volts of the motor and lamps is their rated voltage and not the actual voltage. I know the answer is 22.7 Ohms. I get very close, but I am not 100%.. I need to be 100%. If you can also: with the same diagram I need the total current as well! Thank you very much.

Answers

Answer:

22.6622 Ω ≈ 22.7 Ω5.29516 A ≈ 5.3 A

Explanation:

For an electric motor, 1 hp = 746 W, so 1/2 hp = 373 W. Then the total wattage of the load is ...

  Pl = 373 +100 +100 +75 = 648 W

The equivalent resistance is ...

  R = V^2/P = (120 V)^2/(648 W) = 22 2/9 Ω

Adding the wiring resistance, we get a circuit resistance of ...

  22.2222 +0.22 +0.22 = 22.6622 Ω . . . . total circuit resistance

Then the circuit current is ...

  120 V/(22.6622 Ω) ≈ 5.29516 A

Circuit resistance is about 22.7 Ω; circuit current is about 5.3 A.

_____

Exact values are 5099/225 ohms and 27000/5099 amps. Of course, these assume the motor and lamps are purely resistive, which they are not.

Other Questions
Identify next three numbers in this sequence: 2, 6, 3, 9, 6, 18, 15 What attracted immigrants and rural people to the cities? (35 points) Hey please help quickly. :( Question 4Point P is presently located at the origin. Move P, and observe how the rotated images change. Be sure that neither the images nor the preimageoverlap. Record the distances of the vertices of the preimage AABC from P. Do the same for the other images. Round all of your answers to thehundredths place.Thanks so much Suppose we want a 99% confidence interval for the average amount spent on books by freshmen in their first year at college. The amount spent has a normal distribution with standard deviation $34. (a) How large should the sample be to guarantee the margin of error will be no more than $3?(b) If we wanted a smaller margin of error, we would need a sample. (Enter: ''LARGER'', ''SMALLER'' or ''SAME SIZE'', without the quotes.) How are ratios, rates, and unit rates used to solve problems? What does the word 'pungent" mean? IIt's a noun referring to the area of town where immigrants from one nation live t's an adjective meaning something that has an intensely heavy smell. It's a verb meaning to act out in a sudden and emotional outburst. It's an adverb meaning to do something elegantly or with great class. Solve the following system of equations using the elimination method. 2x + 4y = 10 2x + y = 15 I am one of the regions of Texas. I have several natural features that are not in any other region. My region receives the least amount of precipitation(rainfall). I am also the smallest region in Texas. What region am 1? Which of the following groups would create the largest empire in theMiddle East prior to Alexander the Great? PersiansIsraelitesChaldeansAssyrians Please Help Me quick How does the author of "Ethnic Hash", Patricia J. Williams, use rhetoric (effective or persuasive writing) to advance her point of view? *1 pointA. Williams begins with a playful tone but concludes with a cynical one that portrays disdain toward her convoluted ethnic identity.B. Williams uses irony throughout the article to communicate her feeling of displacement from the ethnic identity of the rest of the culture.C. Williams employs a humorous and often sarcastic tone to communicate the complexity of representing her composite ethnic identity in a single dish.D. Williams includes personal stories and vivid imagery to communicate her desire for an ethnic identity that both simplifies her heritage and disproves stereotypes Which of the following correctly uses absolute value to show the distance between -50 and 12? A: |-50 - 12| = |-62| = -62 units B: |-50 + 12| = |-38| = 38 units C: |-50 + 12| = |-38| = -38 units D: |-50 - 12| = |-62| = 62 units Service Costs are part of maintaining your car. It's that time again. You will need an oil change costing $45, four new tires costing $89.95 each, and 2 new windshield wipers costing $7.95 each. What is the total cost of your service cost? when was the first civil WAR? QUESTION 3Why did the Johnson Reed Act use the Census of 1890 as its basis for determining immigration quotas by nation?A. The authors of the act were trying to ignore the demands of the Immigration Restriction League.B. 1892 was before large numbers of immigrants from Italy, Russia, and central and eastern Europe came to the US.C. The Johnson Reed Act prohibited the immigration of Chinese, and no Chinese had come to the United States before 1890.D. 1890 was the most recent census available when the act was passed in 1924. it can be easier to learn medical terminology if student first study what 3. [W] Consider the following data from NASA about the density of the sun. When you are 10% of the way out from the center of the sun (use x = 0.1), the density is approximately 82.9619 g/cm3 . When you are 20% of the way out of the sun, the density is approximately 38.7504 g/cm3 . When you are 70% of the way out of the sun, the density is approximately 1.7819 g/cm3 . When you are 80% of the way out of the sun, the density is approximately 1.9824 g/cm3 . When you are 90% of the way out of the sun, the density is approximately 0.7859 g/cm3 . We want to use this data to find a quartic (4th degree) interpolating polynomial for the density of the sun throughout. y = Ax4 + Bx3 + Cx2 + Dx + E (a) Set up this problem as a system of linear equations. (b) Find the quartic polynomial that goes through these data points. (c) Use this polynomial to approximate the density 50% of the way out of the sun. What did the Supreme Court decision in the slaughterhouse cases do for the American businesses?A) it allowed food industries to work in citiesB) it opened companies to more shareholdersC) it removed rules from food industriesD) it showed that they have rightsthe first one to answer will be named brainliest Maggie is converting 10,560 feet to miles by using StartFraction 10,560 feet Over 1 EndFraction times StartFraction 1 mile Over 5,280 feet EndFraction. What should be Maggies answer?Her answer should be One-half mile because there are 5,280 feet in a mile.Her answer should be One-half mile because there are 10,560 feet in a mile.Her answer should be 2 miles because there are 5,280 feet in a mile.Her answer should be 2 miles because there are 10,560 feet in a mile. chole is baking cookies to sell in boxes of 12 cookies.if she bakes 122 cookies,calculate the number she can fill and the number of cookies that will be left over.explain your answer