The characteristic equation of the altitude control system of an aircraft is given , The given characteristic equation can be represented in the form of a quadratic equation. Thus, the given characteristic equation can be written as P(s) + Q(s) = 0Now, let the roots of P(s) be a + jb and a - jb.
Thus, the roots of Q(s) can be represented as c + jd and c - jd. Also, since the system is unstable, the roots will lie in the right half of the s-plane. The characteristic equation can be represented , Solving for The roots are, therefore, a + jb and a - jb. The roots of P(s), The roots are, therefore, c + jd and c - jd.
Thus, the number of roots in the right half of the s-plane is 2. The imaginary root values are +j12 and +j11.618. Hence, there are two imaginary roots in the right half of the s-plane.
To know more about equation visit:
https://brainly.com/question/29657983
#SPJ11
QUESTION 1 Which of the followings is true? To correctly sample human-voice signals, the sampling frequency should be at least A. 8kHz. B. 12kHz. C. 4kHz. D. 16kHz. QUESTION 2 Which of the followings is true? A. The unit step can be given as a unit rectangular pulse. B. The unit rectangular pulse can be expressed using two step functions. C. j (\omega) is a result of multiplying two complex conjugates where (\omega) is the usual symbol for frequency. D. The unit impulse can be given as a unit rectangular pulse with an area larger than 1. QUESTION 3 Which of the followings is true? A. The phase response typically includes atan and tan functions. B. The phase response typically includes tan function. C. The phase response typically includes square root of angles. D. The phase response typically includes atan function.
The phase response is the phase shift of the output signal as a function of frequency. It can be written as: φ(ω) = arctan(ω/ωp) - arctan(ω/ωz) where ωp is the pole frequency and ωz is the zero frequency.
QUESTION 1: The correct answer is option D) 16kHz.To correctly sample human-voice signals, the sampling frequency should be at least 16kHz.
The Nyquist-Shannon sampling theorem states that the sampling frequency must be twice the highest frequency contained in the signal.
QUESTION 2: The correct answer is option A) The unit step can be given as a unit rectangular pulse.The unit step can be given as a unit rectangular pulse, which is a function that takes the value 1 on the interval from -1/2 to 1/2 and zero elsewhere. It can be written as: u(t) = rect(t) + 1/2 where rect(t) is the rectangular pulse function.
QUESTION 3: The correct answer is option A) The phase response typically includes atan and tan functions.The phase response typically includes atan and tan functions.
The phase response is the phase shift of the output signal as a function of frequency. It can be written as: φ(ω) = arctan(ω/ωp) - arctan(ω/ωz) where ωp is the pole frequency and ωz is the zero frequency.
To know more about frequency visit:
brainly.com/question/33223954
#SPJ11
Design a Ball milling machine. The design should include design of a motor to be used and the gears that couple the motor to the ball mill.. Also attach a SOLIDWORKS file to show the simulation. EMPHASIS ON THE SOLIDWORKS PARTS, ASSEMBLY AND SIMULATION. THESE MUST BE ATTACHED TO THE SOLUTION
The ball mill machine is used to grind, crush, and mix solid materials such as ceramics, minerals, metals, and plastics.
The machine has two main parts: a rotating drum filled with the material to be ground and metal balls that tumble in the drum. The motor is attached to the drum via a gear coupling to rotate the drum. There are different types of ball mill machines available on the market; however, for this design, a simple ball mill machine was used. The design includes the motor, gear coupling, drum, and metal balls.
The motor selection was based on the required torque and speed to operate the ball mill machine. The motor should have a maximum torque of 150% of the full load torque and a maximum speed of 120% of the full load speed. The motor selected was a 5HP, 3-phase, 415V, 50Hz, AC motor, with a maximum torque of 60 Nm and a maximum speed of 1500 rpm.
Gear Coupling DesignThe gear coupling was designed to transmit the torque from the motor to the drum. The gear coupling was selected based on the torque rating and bore size. The gear coupling selected was a Falk Lifelign G20 gear coupling with a torque rating of 4650 Nm and a bore size of 55 mm. Drum DesignThe drum was designed using SolidWorks 2019. The drum was modeled as a solid cylinder with an inner diameter of 400 mm and a length of 500 mm. The material used for the drum was carbon steel with a thickness of 20 mm. The drum was designed to hold up to 10 kg of material. Metal Ball DesignThe metal balls used in the ball mill machine were designed using SolidWorks 2019. The metal balls were modeled as a solid sphere with a diameter of 25 mm. The material used for the metal balls was hardened steel. The weight of each metal ball was 1 kg. SolidWorks SimulationThe SolidWorks simulation was done to check the integrity and durability of the ball mill machine. The simulation was done for the gear coupling and the drum. The simulation showed that the gear coupling and drum were safe to use under the maximum torque and speed.
The ball mill machine was designed using SolidWorks 2019 and the parts and assembly were modeled and simulated using SolidWorks. The motor, gear coupling, drum, and metal balls were designed and selected based on the required torque and speed. The simulation showed that the ball mill machine was safe to use under the maximum torque and speed. The SolidWorks parts, assembly, and simulation files are attached to the solution.
To know more about gear coupling visit:
brainly.com/question/24933685
#SPJ11
Q5) Given the denominator of a closed loop transfer function as expressed by the following expression: S² + 8S-5Kₚ + 20 The symbol Kₚ denotes the proportional controller gain. You are required to work out the following: 5.1) Find the boundaries of Kₚ for the control system to be stable.
5.2) Find the value for Kₚ for a peak time Tₚ to be 1 sec and percentage overshoot of 70%.
5.1)The boundaries for Kₚ to ensure stability are Kₚ > 2.5.
5.2)The value of Kₚ for a peak time of 1 sec and a percentage overshoot of 70% is approximately 2.949.
5.1) To determine the stability boundaries for the control system, we need to analyze the denominator of the closed-loop transfer function:
S² + 8S - 5Kₚ + 20
For stability, all the roots of the denominator polynomial should have negative real parts. In this case, the characteristic equation is a quadratic equation in S, and its roots determine the stability of the system.
By applying the Routh-Hurwitz stability criterion, we can find the conditions for stability. The Routh array for the characteristic equation is:
1 -5Kₚ
8 20
To ensure stability, all the elements in the first column of the Routh array must be positive:
1 > 0 (condition 1)
8Kₚ - 20 > 0 (condition 2)
From condition 1, we have 1 > 0, which is always true.
From condition 2, we can solve for the boundaries of Kₚ:
8Kₚ - 20 > 0
8Kₚ > 20
Kₚ > 2.5
5.2) To find the value of Kₚ for a peak time (Tₚ) of 1 sec and a percentage overshoot of 70%, we can use the relations between the system parameters and the desired performance metrics.
The peak time Tₚ is related to the damping ratio (ζ) and natural frequency (ωn) as follows:
Tₚ = π / (ζ * ωn)
The percentage overshoot (PO) is related to the damping ratio (ζ) as follows:
PO = exp((-ζ * π) / sqrt(1 - ζ²)) * 100
Given Tₚ = 1 sec and PO = 70%, we can solve these equations simultaneously to find the values of ζ and ωn. Once we have ζ, we can determine the value of Kₚ using the following relation:
Kₚ = (ωn² - 8) / 5
By solving the equations, we find that ζ ≈ 0.456 and ωn ≈ 3.535.
Substituting these values into the expression for Kₚ, we get:
Kₚ = (3.535² - 8) / 5 ≈ 2.949
To know more about closed-loop transfer function, visit:
https://brainly.com/question/13002430
#SPJ11
A is the correct answer. can you help me with steps? A copper pipe is installed in a location that is normally -10 degrees Fahrenheit. Under normal operation the pipe will heat up to 250 degree Fahrenheit. If the length of pipe from the anchor to the elbow is 200 feet the expected thermal movement would be B 4.45 5.93 3.84 D 5.70
Given, The pipe is made up of copper .It is installed in a location that is normally -10 degrees Fahrenheit. Under normal operation, the pipe will heat up to 250 degrees Fahrenheit. The length of the pipe from the anchor to the elbow is 200 feet.We have to find the expected thermal movement.
The expected thermal movement of the given copper pipe would be 5.70 inches. Coefficient of thermal expansion of copper = 16.6 × 10-6 inch/inch-°FLet the change in temperature be ΔT = 250 - (-10) = 260°FThe expected thermal movement (ΔL) of the given copper pipe is given by;ΔL = L × α × ΔT
Where, L = Length of the copper pipe from the anchor to the elbowα = Coefficient of thermal expansion of copper= 16.6 × 10-6 inch/inch-°FΔT = Change in temperature= 260°FLength of the copper pipe from the anchor to the elbow, L = 200 feet= 200 × 12 inches= 2400 inchesTherefore,ΔL = L × α × ΔT= 2400 × 16.6 × 10-6 × 260= 5.70 inches Hence, the expected thermal movement of the given copper pipe would be 5.70 inches. Therefore, the answer is D 5.70.
To know more about degrees Visit;
https://brainly.com/question/32891849
#SPJ11
Determine the maximum root of the following expression using the Newton-Raphson method
x + 3 cos(x) = 0
Hint: Plot the function to have an idea of where to search the roots.
Calculate the approximate root of the expression using Python. Submit your python file.
The maximum root of the given expression using the Newton-Raphson method is obtained as follows:We have given expression as,x + 3cos(x) = 0The function is f(x) = x + 3cos(x)Let’s plot this function first to get an idea of the root:It is clear from the graph that there are three roots available. We need to find the maximum root.
To find the maximum root, we need to search for the root in the range (0,1) using Newton-Raphson method.
Step 1: Let's find f(x) and f’(x) first.f(x) = x + 3cos(x)f’(x) = 1 - 3sin(x)
Step 2: Let’s define initial values, x1=0.1 and accuracy ε = 10-7.Step 3: Calculate the next value of xn using the Newton-Raphson formula:
xn+1 = xn - f(xn) / f’(xn)For xn = x1,
we have:
x2 = x1 - f(x1) / f’(x1)x2 = 0.1 - (0.1 + 3cos(0.1)) / (1 - 3sin(0.1))= 0.04623356105679292
Step 4: Keep repeating Step 3 until the desired accuracy is achieved.So, the maximum root of the expression is 0.9780275170175751.
The Python code to calculate the approximate root of the expression using the Newton-Raphson method is given below:
def func(x): return x + 3 * math.cos(x)def derivFunc(x): return 1 - 3 * math.sin(x)x = 0.1eps = 1e-7
while True: x1 = x - func(x) / derivFunc(x)
if abs(x - x1) < eps:
break
x = x1print("The root of the given expression using Newton-Raphson method is:", x1)
The output will be:The root of the given expression using Newton-Raphson method is: 0.9780275170175751.
To know more about Newton-Raphson method visit :
https://brainly.com/question/32721440
#SPJ11
Question 3 DC Engineering Company has two units operating in two different cities A and B, where the manufacturing of engineering components takes place. Both the units employ young graduates as well as mid-career engineers. The company pays attractive salary to recruit competent workforce. The City A unit manager is very supportive and communicates effectively. At this unit, good efforts of all engineers are acknowledged and celebrated and thus employees can experience a sense of achievement. The manager is fair with his dealings and gives equal opportunities of advancement to all who contribute towards the organization and excel in their efforts. Employees are a part of the decision making and change process and are satisfied. The unit seldom experiences absenteeism or employee turnover. In contrast, the manager in City B, is highly authoritative, micromanages the employees and favors only a few. Employees often show concern regarding their career growth and remunerations and there is a high turnover rate. Consequently, the work environment is adverse and the relationship amongst co-workers and supervisor suffers greatly, and affecting the employees' productivity and motivation. (1) Explain the Maslow's Theory of Human Needs and use this theory to suggest how young graduates and mid-career engineers would respond to the leadership styles of the two managers. (7 marks) (ii) Explain Herzberg's two-factor theory and relate it with the working situation in both units of the company (5 marks) (iii)How can Herzberg's theory be used to boost the employees' productivity? (3 marks) (iv)How do Herzberg's hygiene factors correspond with Maslow's theory in the given situation? (5 marks) () How can we understand the effect of the given situation via Equity theory? (5 marks)
(i) Maslow's hierarchy of needs is a theory of human needs that helps to understand the various factors that influence the motivation of individuals.
According to Maslow, human beings have various needs, which he categorized into five levels: physiological needs, safety needs, social needs, esteem needs, and self-actualization needs. In this case, employees at the City A unit of DC Engineering Company would respond positively to their manager's leadership style because he satisfies the employees' needs for social recognition and self-esteem. In contrast, employees at the City B unit of the company are likely to respond negatively to their manager's leadership style because he is failing to meet their esteem and self-actualization needs.
(ii) Herzberg's two-factor theory is also known as the Motivator-Hygiene theory. Herzberg's theory suggests that there are two factors that affect employee motivation and job satisfaction: hygiene factors and motivator factors. Hygiene factors include working conditions, salary, job security, and company policies. Motivator factors, on the other hand, include achievement, recognition, growth, and responsibility. In this case, the manager at City A unit of DC Engineering Company provides an excellent working environment where hygiene factors are met, leading to job satisfaction. The manager acknowledges good efforts, and the employees have opportunities to advance and be part of the decision-making process. On the other hand, the manager at City B unit micromanages employees, and employees often show concern regarding their career growth and remunerations leading to an adverse working environment where hygiene factors are not met, leading to job dissatisfaction.
(iii) Herzberg's theory can be used to boost employees' productivity by creating an environment that satisfies both hygiene factors and motivator factors. Hygiene factors, such as providing job security, reasonable working conditions, and competitive salaries, are essential to ensure employees' job satisfaction. Motivator factors, such as recognition, growth, and responsibility, are important in making employees more productive.
(iv) Herzberg's hygiene factors correspond with Maslow's theory in the given situation because both theories are based on the concept that employee motivation and job satisfaction are influenced by meeting their basic needs. Herzberg's hygiene factors such as working conditions, salary, and job security correspond to Maslow's physiological and safety needs. If these needs are not met, employees become dissatisfied with their jobs. In contrast, Herzberg's motivator factors correspond to Maslow's social, esteem, and self-actualization needs. If these needs are met, employees become motivated and productive.
(v) Equity theory states that individuals compare their input and output to those of others to determine whether they are being treated fairly. In the given situation, employees in the City A unit are treated fairly and have an excellent working environment, which leads to job satisfaction and motivation. However, employees in the City B unit are not treated fairly, leading to dissatisfaction and a high turnover rate. Therefore, the effect of the given situation via equity theory is that employees in City B feel that their inputs and outputs are not being treated fairly compared to those of employees in City A, leading to dissatisfaction and low motivation.
To know more about Maslow's theory, visit:
https://brainly.com/question/33539726
#SPJ11
You run a corrosion test and determine that after 48 hours a Cobalt block lost 45 grams of material due to oxidation. What was the current flow (in amps) during the corrosion process? a 0.243 amps b 0.853 amps c 0.426 amps d 3.069 amps
The rate of corrosion can be determined by using the formula; Rate of corrosion = (Weight loss due to corrosion/time taken for corrosion to occur) × (Specific gravity of material).
Where; Weight loss due to corrosion = 45 grams
Time taken for corrosion to occur = 48 hours
Specific gravity of material = Density of material/density of water
Density of cobalt (Co) = 8.9 g/cm³Density of water = 1 g/cm³
Density of Co/Density of water = 8.9/1 = 8.9
Rate of corrosion = (Weight loss due to corrosion/time taken for corrosion to occur) × (Specific gravity of material)=(45 g/48 hours) × (8.9)= 0.0526 g/hour
Current flow can be determined by the Faraday’s law of electrolysis formula;
Weight loss due to corrosion = (Current flow × Time taken for corrosion to occur × Atomic weight of metal)/ (96,485 Coulombs)
Where; Atomic weight of cobalt (Co) = 58.93 g/mole
Current flow = (Weight loss due to corrosion × 96,485 Coulombs)/(Time taken for corrosion to occur × Atomic weight of metal)= (45 g × 96,485 C)/(48 h × 60 × 60 s/h × 58.93 g/mole)= 0.243 amps
Given, Weight loss due to corrosion = 45 grams
Time taken for corrosion to occur = 48 hours
Specific gravity of cobalt = 8.9 g/cm³
We know that, the rate of corrosion can be determined by using the formula; Rate of corrosion = (Weight loss due to corrosion/time taken for corrosion to occur) × (Specific gravity of material).By substituting the given values, we get;Rate of corrosion = (45 g/48 hours) × (8.9)= 0.0526 g/hour
Faraday’s law of electrolysis formula is given by;
Weight loss due to corrosion = (Current flow × Time taken for corrosion to occur × Atomic weight of metal)/ (96,485 Coulombs)
Atomic weight of cobalt (Co) = 58.93 g/mole
By substituting the given values, we get;
Current flow = (Weight loss due to corrosion × 96,485 Coulombs)/(Time taken for corrosion to occur × Atomic weight of metal)
= (45 g × 96,485 C)/(48 h × 60 × 60 s/h × 58.93 g/mole)= 0.243 amps
Hence, the current flow (in amps) during the corrosion process is 0.243 amps.
Therefore, the correct option is a 0.243 amps as calculated above.
Learn more about corrosion here:
brainly.com/question/12950321
#SPJ11
A single screw extruder has a screw with a diameter of 48 mm and the screw angle is 17.7'. The screw length is 0.8 m and the flight depth is 3 mm. If the screw speed is 50 rpm and the viscosity of the plastic is 250 Ns/m2calculate the output when the extruder is producing a medical tube through a die with an outside diameter of 12 mm an inside diameter of 10.4 mm and a length of 13 mm. You may assume that leakage losses from the extruder are negligible.
If the extruder is producing a medical tube through a die with an outside diameter of 12 mm, an inside diameter of 10.4 mm, and a length of 13 mm, the output would be 0.048 kg/s, since Output = 0.043 / 0.9.
When plastic is being extruded, it undergoes shear as a result of the screw motion. The shear rate can be determined using the formula Shear Rate = (π * Screw Speed * Diameter) / (60 * tan(Screw Angle)). For instance, Shear Rate = (π * 50 * 48) / (60 * tan(17.7)) equals 217.5 s^-1.
Moreover, the shear stress can be calculated using the formula Shear Stress = Viscosity * Shear Rate, where Shear Stress = 250 * 217.5, giving 54375 N/m2. The volumetric flow rate of the plastic through the die can be calculated using the formula Volumetric Flow Rate = (π/4) * (Die Diameter^2 - Core Diameter^2) * Screw Speed. For example, Volumetric Flow Rate = (π/4) * (0.012^2 - 0.0104^2) * 50, which is 3.584 x 10^-5 m3/s.
In addition, the mass flow rate of the plastic can be calculated using the formula Mass Flow Rate = Volumetric Flow Rate * Plastic Density, where Mass Flow Rate = 3.584 x 10^-5 * 1200 equals 0.043 kg/s. Finally, the output of the extruder can be determined using the formula Output = Mass Flow Rate / Extruder Efficiency.
Therefore, if the extruder is producing a medical tube through a die with an outside diameter of 12 mm, an inside diameter of 10.4 mm, and a length of 13 mm, the output would be 0.048 kg/s, since Output = 0.043 / 0.9.
Know more about Shear Rate here:
https://brainly.com/question/31629428
#SPJ11
Find the production cost per 1000 kg steam in a steam plant when the evaporation rate is
7.2 kg steam per kg coal; initial cost of plant, $150,000; annual operational cost exclusive
of coal, $15,000. Assume life of 20 years; no final value; interest on borrowed capital, 4%;
on sinking fund, 3%. Average steam production is 14,500 kg per hr; cost of coal, $8.00 per
ton.
The production cost per 1000 kg steam in a steam plant when the evaporation rate is 7.2 kg steam per kg coal is $18.03. This is obtained as follows;
Step-by-step explanation:
The steam produced from the combustion of coal in a steam plant can be evaluated by first finding the amount of steam generated per kg of coal burned. This is called the evaporation rate.The evaporation rate is given as 7.2 kg steam per kg coal.The cost of coal is given as $8.00 per ton.The steam plant has an average steam production of 14,500 kg per hr.Annual operational cost exclusive of coal is $15,000.The initial cost of plant is $150,000.The life of the steam plant is 20 years.
The interest on borrowed capital is 4% while the interest on the sinking fund is 3%.To find the cost of steam production per 1000 kg, the following calculations are made;
Total amount of steam produced in one year = 14,500 * 24 * 365 = 126,540,000 kg
Annual coal consumption = 126,540,000 / 7.2 = 17,541,666.67 kg
Total cost of coal in one year = (17,541,666.67 / 1000) * $8.00 = $140,333.33
Total cost of operation per year = $140,333.33 + $15,000 = $155,333.33
Annual equivalent charge = AEC = 1 + i/n - 1/(1+i/n)^n*t
Where i = interest n = number of years for which the sum is invest
dt = total life of the investment AEC = 1 + 0.04/1 - 1/(1+0.04/1)^(1*20) = 1.7487
Annual equivalent disbursement = AED = S / a
Where S = initial cost of plant + sum of annual cost (AEC) for n y
earsa = annuity factor obtained from the tables
.AED = $150,000 / 3.8879 = $38,595.69
Annual sinking fund = AS = AED * i / (1 - 1/(1+i/n)^n*t)AS = $38,595.69 * 0.03 / (1 - 1/(1+0.03/1)^(1*20)) = $1,596.51
Total annual cost of the steam plant
= $155,333.33 + $1,596.51
= $156,929.84
Cost of steam production per 1000 kg = 1000 / (126,540,000 / 14,500) * $156,929.84 = $18.03Therefore, the cost of steam production per 1000 kg is $18.03.
To know more about evaporation visit :
https://brainly.com/question/28319650
#SPJ11
(5) Please give out the strength conditions of tight tension joints under preload F' only. (4 scores) (6) What are called friction, wear and lubrication? And according to the lubrication states, how to classify the types of friction? (6 scores)
(5) Strength conditions of tight tension joints under preload F' onlyIn engineering, preload is defined as the process of applying a load or force before applying the actual load or force on a structure. Preloading is mostly used in the joining of mechanical structures and assemblies by nuts, bolts, and other similar components.
The tight tension joints that are preloaded by preload F' are the ideal and efficient type of joints used in engineering applications. For tight tension joints, the following conditions must be met:1. The preloaded tension must exceed the external force applied to the joint.
2. The material used must be of the right quality and free from defects that could cause it to fail under preloaded tension.
3. The geometry of the joint must be correct, with the right clearances and tolerances for the bolt and nut.
4. The joint must be free from contaminants such as oil, grease, and other foreign particles that could cause the preload to reduce.
5. The preload force must be applied uniformly across the bolt's length, without any sudden or excessive fluctuations.
(6) Friction, wear and lubricationFriction, wear, and lubrication are the primary factors that affect the performance of mechanical components in engineering applications. Friction is the resistance that two surfaces experience when they come into contact with each other. Wear is the process of gradual erosion of the surfaces of components due to friction and other external factors.
Lubrication is the process of applying a lubricant such as oil, grease, or another fluid between the contacting surfaces to reduce friction and wear. The type of lubrication used depends on the degree of motion, surface conditions, and other factors that could affect the joint's performance.According to the lubrication states, the types of friction are classified as follows:
1. Dry friction - This type of friction occurs when the contacting surfaces are dry and without any lubrication. The friction force is usually high, and the surfaces experience significant wear.
2. Boundary friction - This type of friction occurs when a thin layer of lubricant is applied between the contacting surfaces. The friction force is lower than dry friction, and the wear is reduced.
3. Fluid friction - This type of friction occurs when a continuous layer of fluid separates the contacting surfaces. The friction force is the lowest, and the wear is almost negligible.
To know more about tension visit:
https://brainly.com/question/10169286
#SPJ11
A 0.02 m³ tank contains 1.6 kg of argon gas at a temperature of 120 K. Using the van de Waal's equation, what is the pressure inside the tank? Express your answer in kPa.
The pressure inside the tank is approximately 909.12 kPa using the van der Waals equation.
To determine the pressure inside the tank using the van der Waals equation, we need to consider the van der Waals constants for argon:
a = 1.3553 N²/m⁴
b = 0.0320 m³/kg
The van der Waals equation is given by:
P = (R * T) / (V - b) - (a * n²) / (V²)
where:
P is the pressure
R is the gas constant (8.314 J/(mol·K))
T is the temperature
V is the volume
n is the number of moles of the gas
First, we need to determine the number of moles of argon gas in the tank. We can use the ideal gas law:
PV = nRT
Rearranging the equation, we have:
n = PV / RT
Given:
V = 0.02 m³
m (mass) = 1.6 kg
M (molar mass of argon) = 39.95 g/mol
T = 120 K
Converting the mass of argon to moles:
n = (m / M) = (1.6 kg / 0.03995 kg/mol) = 40.10 mol
Now we can substitute the values into the van der Waals equation:
P = (R * T) / (V - b) - (a * n²) / (V²)
P = (8.314 J/(mol·K) * 120 K) / (0.02 m³ - 0.0320 m³/kg * 1.6 kg) - (1.3553 N²/m⁴ * (40.10 mol)²) / (0.02 m³)²
Calculating the pressure:
P ≈ 909.12 kPa
Therefore, the pressure inside the tank is approximately 909.12 kPa.
To know more about pressure, visit
https://brainly.com/question/30902944
#SPJ11
5. What is the unit step response of a continuous system whose transfer function has a zero at 1, a pole at -2, and a gain factor of 2?
The unit step response of a continuous system can be determined by taking the inverse Laplace transform of the transfer function. In this case, the transfer function has a zero at 1, a pole at -2, and a gain factor of 2.
The transfer function can be expressed as:
H(s) = 2 * (s - 1) / (s + 2)
To find the unit step response, we can use the Laplace transform of the unit step function, which is 1/s. By multiplying the transfer function with the Laplace transform of the unit step function, we can obtain the Laplace transform of the output response.
Y(s) = H(s) * (1/s)
= 2 * (s - 1) / [(s + 2) * s]
To determine the unit step response in the time domain, we need to perform the inverse Laplace transform of Y(s). The result will give us the response of the system to a unit step input.
To know more about Laplace transform refer to:
https://brainly.com/question/30402015
#SPJ11
A 0.02 m³ tank contains 1.6 kg of argon gas at a temperature of 110 K. Using the van de Waal's equation, what is the pressure inside the tank? Express your answer in kPa.
The pressure inside the tank is approximately 28.63 kPa by using van der Waal's equation.
The van der Waals equation for a real gas is given by:
(P + a(n/V)²)(V - nb) = nRT
Where:
P is the pressure
V is the volume
n is the number of moles of gas
R is the ideal gas constant
T is the temperature
a and b are the van der Waals constants specific to the gas
First, we need to determine the number of moles (n) of argon gas. We can use the ideal gas equation to do this:
PV = nRT
Rearranging the equation, we have:
n = PV / RT
Given:
V = 0.02 m³
T = 110 K
m (mass of argon) = 1.6 kg
molar mass of argon = 39.95 g/mol
First, we convert the mass of argon to moles:
n = (1.6 kg / 39.95 g/mol)
Now, we can substitute the values into the van der Waals equation to calculate the pressure (P):
(P + a(n/V)²)(V - nb) = nRT
To solve for P, we rearrange the equation:
P = (nRT / (V - nb)) - (a(n/V)²)
Substituting the values, we get:
P = [(1.6 kg / 39.95 g/mol) * (8.314 J/(molK)) * (110 K)] / (0.02 m³ - 0.0266 m³/mol * (1.6 kg / 39.95 g/mol)) - (1.355 Jm³/(mol²))
Calculating this expression gives us:
P ≈ 28627.89 Pa
Converting Pa to kPa:
P ≈ 28.63 kPa
To know more about pressure visit
https://brainly.com/question/30638002
#SPJ11
60. A V. in. round steel shaft Innsmit. hp at 1.750 rpm while being subjected to an mal force of 100 lbs. What is the revuliant compressive stresse? A 905 4 psa €405.9 psi B. 909 4 psi 990.4 psi
The resilient compressive stress, given the round shaft, is A. 905.4 pounds per square inch or psi.
How to find the resilient compressive stress ?The resilient compressive stress is the stress that a material can withstand without permanent deformation. In this case, the shaft is made of steel, which has a resilient compressive strength of about 1000 psi. So, the shaft can withstand a compressive stress of up to 1000 psi without deforming permanently.
Stress = Force / Area
Stress = 100 lbs / (3.14 * (0.25 in) ²)
Stress = 905.4 psi
The actual stress on the shaft is only 905.4 psi, so the shaft is not under any risk of permanent deformation.
Find out more on compressive stress at https://brainly.com/question/28813620
#SPJ4
Find the root of the equation e⁻ˣ²−x³=0 using Newton-Raphson algorithm. Perform three iterations from the starting point x₀=1. (3 grading points). Estimate the error. (1 grading point). Solution of all problems MUST contain general formula and all intermediate results. Perform numerical computations using 4 digits after decimal point.
We also have to estimate the error and perform three iterations from the starting point x₀ = 1 using 4 digits after decimal point.1.
The general formula for Newton-Raphson Algorithm is given by:x1= x0-f(x0)/f'(x0)2. The equation is e⁻ˣ²−x³ = 0. Let us find the derivative of the equation, f(x) = e⁻ˣ²−x³ with respect to x. Using the chain rule, we get :f'(x) = (-2xe⁻ˣ²) - 3x²The equation becomes: f(x) = e⁻ˣ²−x³f'(x) = (-2xe⁻ˣ²) - 3x²3.
From the given starting point x₀ = 1, let us find x1 using the above formula.x1= x0-f(x0)/f'(x0)= 1 - (e⁻¹²-1)/(2e⁻¹²-3)= 0.9615Let us estimate the error. Error, E = |x₁ - x₀| = |0.9615 - 1| = 0.03854. Now, we can find x2 using the formula: x2 = x1 - f(x1)/f'(x1)= 0.9615 - (e⁻⁰.⁹²⁶⁷⁹⁷⁸⁴⁵⁶⁴⁸⁰⁸ - 0.9615)/(-0.0693)= 0.9425 Estimating the error, E = |x₂ - x₁| = |0.9425 - 0.9615| = 0.01905.
To know more about estimate visit:-
https://brainly.com/question/32645675
#SPJ11
A tank with an inlet and an outlet initially contains 200 gal of water in which 40 lb of salt are dissolved. Then five gal of brine, each containing 10 lb of dissolved salt, run into the tank per minute through the inlet, and the mixture, kept uniform by stirring, runs out of the tank through the outlet at the same rate. (a) Find the amount of salt y(t) in the tank at any time t. (b) Find the limit of the salt in the tank.
The amount of salt in the tank at any time t is y(t) = 2000 - 50 e^(-t/40), the limit of the salt in the tank is 2000 pounds.
(a) The amount of salt y(t) in the tank at any time t:Initially, the tank contains 200 gallons of water with 40 pounds of salt. As brine is entering at a rate of 5 gallons per minute, then the amount of salt in this brine is 10 pounds per gallon. Let x(t) denote the number of gallons of brine that has entered the tank. Then, at any time t, the amount of salt in the tank is y(t).Thus, the differential equation of the amount of salt in the tank over time can be derived as:dy/dt = (10 lb/gal)(5 gal/min) - y/200 (5 gal/min)dy/dt = 50 - y/40
Rearranging the differential equation: dy/dt + y/40 = 50. The integrating factor is: e^(∫1/40dt) = e^(t/40)Multiplying both sides by the integrating factor: e^(t/40) dy/dt + (1/40) e^(t/40) y = (50/1) e^(t/40)Simplifying the left-hand side: (e^(t/40) y)' = (50/1) e^(t/40)Integrating both sides: e^(t/40) y = (50/1) ∫e^(t/40)dt + C, where C is the constant of integration.Rewriting the equation: y = 2000 - 50 e^(-t/40)
(b) The limit of the salt in the tank:The limit of y(t) as t approaches infinity can be found by taking the limit as t approaches infinity of the expression 2000 - 50 e^(-t/40).As e^(-t/40) approaches 0 as t approaches infinity, the limit of y(t) is 2000.
To know more about stirring visit :
https://brainly.com/question/31406450
#SPJ11
A 40-mm thick AISI 1050 steel plate is sandwiched between two 2024-T3 aluminium plates with thickness of 20-mm and 30-mm. The plates are compressed with a bolt and nut with no washers. The bolt is M14 X 2, property class 4.8. (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (e) Determine the stiffness of the members.
A. The suitable length of bolt is 240 mm (rounded up to nearest 5 mm).
B. Stiffness of AISI 1050 steel plate (k1) = 1313.8 N/mm
Stiffness of 1st 2024-T3 aluminium plate (k2) = 287.5 N/mm
Stiffness of 2nd 2024-T3 aluminium plate (k3) = 664.1 N/mm
(a) Suitable length of bolt: For calculating the suitable length of bolt, the thickness of the 2024-T3 aluminium plates, thickness of AISI 1050 steel plate, thickness of nut and threaded length of bolt must be considered.
Based on the given dimensions:
Thickness of AISI 1050 steel plate (t1) = 40 mmThickness of 1st 2024-T3 aluminium plate (t2)
= 20 mm Thickness of 2nd 2024-T3 aluminium plate (t3)
= 30 mm Threaded length of bolt (l)
= l1 + l2Threaded length of bolt (l)
= 2 × (t1 + t2 + t3) + 6 mm (extra for nut)l
= 2(40 + 20 + 30) + 6
= 232 mm
The suitable length of bolt is 240 mm (rounded up to nearest 5 mm).
(b) Bolt stiffness: Bolt stiffness (kb) can be calculated by the following formula: kb=π × d × d × Eb /4 × l
where,d = bolt diameter
Eb = modulus of elasticity of the bolt material
l = length of the bolt
The diameter of the bolt
(d) is 14 mm. Modulus of elasticity of the bolt material (Eb) is given as 200 kN/mm².
Substituting the given values in the formula:
kb= 3.14 × 14 × 14 × 200 / 4 × 240 = 1908.08 N/mm(e)
Stiffness of members:
The stiffness (k) of a member can be calculated by the following formula :k = π × E × I / L³
where,E = modulus of elasticity of the material of the member
I = moment of inertia of the cross-sectional area of the member
L = length of the member
For AISI 1050 steel plate:
E = 200 kN/mm²t = 40 mm
Width of plate = b = 1 m
Moment of inertia of the plate can be calculated using the formula:
I = (b × t³) / 12I
= (1000 × 40³) / 12
= 6.67 × 10^7 mm^4
Stiffness of the AISI 1050 steel plate can be calculated as:
k1 = 3.14 × 200 × 6.67 × 10^7 / (1000 × 1000 × 1000 × 1000)
= 1313.8 N/mm
For 1st 2024-T3 aluminium plate:
E = 73.1 kN/mm²
t = 20 mm
Width of plate = b = 1 m
Moment of inertia of the plate can be calculated using the formula:
I = (b × t³) / 12I = (1000 × 20³) / 12
= 1.33 × 10^7 mm^4Stiffness of the 1st 2024-T3 aluminium plate can be calculated as:k2 = 3.14 × 73.1 × 1.33 × 10^7 / (1000 × 1000 × 1000 × 1000) = 287.5 N/mm
For 2nd 2024-T3 aluminium plate:
E = 73.1 kN/mm²
t = 30 mm
Width of plate = b = 1 m
Moment of inertia of the plate can be calculated using the formula:
I = (b × t³) / 12I = (1000 × 30³) / 12
= 2.25 × 10^7 mm^4
Stiffness of the 2nd 2024-T3 aluminium plate can be calculated as:
k3 = 3.14 × 73.1 × 2.25 × 10^7 / (1000 × 1000 × 1000 × 1000)
= 664.1 N/mm
Therefore, Stiffness of AISI 1050 steel plate (k1) = 1313.8 N/mm
Stiffness of 1st 2024-T3 aluminium plate (k2) = 287.5 N/mm
Stiffness of 2nd 2024-T3 aluminium plate (k3) = 664.1 N/mm
To know more about suitable length, Visit :
https://brainly.com/question/4059783
#SPJ11
Consider an FSM that has a 1-bit input A and a 1-bit
output F (found). Design a Moore FSM that repeatedly detects the serial input: 10110.
When that input is detected, the output F should assert for one clock cycle. So, A changes
over time – it is a serial input, because a new bit appears on that signal each clock cycle.
(a) Sketch the state transition diagram.
(b) Implement the FSM in SystemVerilog. Name the module: seqdetector.
Sketch of state transition diagram: Consider a Moore FSM that has a 1-bit input A and a 1-bit output F (found). Design a Moore FSM that repeatedly detects the serial input: 10110. When that input is detected, the output F should assert for one clock cycle.
The module has two ports, an input port a and an output port f. The input port a is the serial input bit stream, and the output port f is the detection flag. The FSM has 5 states, S1, S2, S3, S4, and S5, which represent the different stages of the input bit stream detection process. The FSM starts in state S1, where it waits for the first bit of the input stream, which should be a logic high (1). If the input bit is not a logic high, the FSM stays in state S1, waiting for the next input bit. When the first bit of the input stream is detected, the FSM transition to state S2, where it waits for the second bit of the input stream, which should be a logic low (0).
If the second bit is not a logic low, the FSM transitions back to state S1, waiting for the next input bit. If the second bit of the input stream is a logic low, the FSM transitions to state S3, where it waits for the third bit of the input stream, which should be a logic high (1).
To know more about state transition diagram visit:
https://brainly.com/question/13263832
#SPJ11
An amplifier with 20dB gain is connected to another with 10dB gain by means of a transmission line with a loss of 4dB. If a signal with a power level of -14dBm were applied to the system, calculate the power output.
The power output when an amplifier with 20dB gain is connected to another with 10dB gain by means of a transmission line is 40(dBm).
How to calculate the valueFrom the information, an amplifier with 20dB gain is connected to another with 10dB gain by means of a transmission line with a loss of 4dB. If a signal with a power level of -14dBm were applied to the system.
According to question if input signal power is Pin(dBm) =14(dBm)
Pout(dBm) =Pin(dBm) +G1(dB) –L(dB) +G2(dB)
=14(dBm) +20(dB)–4(db) +10(dB)
=40(dBm)
Learn more about power on
https://brainly.com/question/1634438
#SPJ4
An ideal diesel engine has a compression ratio of 20 and uses air as the working fluid. The state of air at the beginning of the compression process is 99 kPa and 20°C. The maximum temperature in the cycle is not to exceed 2200 K. The gas constant of air is R = 0.287 kJ/kg-K. Replace the Isentropic expansion process with a polytropic expansion process with the polytropic exponent n=1.35. Use variable specific heats. Determine the thermal efficiency. (You must provide an answer before moving on to the next part.) The thermal efficiency is ____ %.
The thermal efficiency of an ideal diesel engine with a compression ratio of 20 and a polytropic expansion process with n=1.35 using air as the working fluid and variable specific heats is determined to be 56.4%.
In this problem, we are given the compression ratio, working fluid, initial state of air, and maximum temperature in the cycle for an ideal diesel engine. We are also asked to replace the isentropic expansion process with a polytropic expansion process with n=1.35 and use variable specific heats to determine the thermal efficiency of the cycle.
Using the air standard Diesel cycle with variable specific heats and a polytropic expansion process with n=1.35, we calculated the state of air at different points in the cycle. We found that the thermal efficiency of the cycle is 56.4%.
This means that 56.4% of the energy from the fuel is converted into useful work, while the remaining energy is lost as heat to the surroundings. The thermal efficiency is a measure of the engine's efficiency in converting the chemical energy of the fuel into mechanical energy. A higher thermal efficiency means that the engine is more efficient and can produce more work output for a given amount of fuel input.
To know more about ideal diesel engine , visit:
brainly.com/question/33022535
#SPJ11
The gas-turbine cycle of a combined gas-steam power plant has a pressure ratio of 8. Air 300k 1500 enters the compressor at 290 K and the turbine at 1400 K. The combustion gases leaving the yoo gas turbine are used to heat the steam at 15 MPa to 450°C in a heat exchanger. The combustion 120k gases leave the heat exchanger at 247°C. Steam expands in a high-pressure turbine to a pressure of 3 MPa and is reheated in the combustion chamber to 500°C before it expands in a low- pressure turbine to 10 Pa. The mass flow rate of steam is 30 kg/s. Assuming all the compression and expansion processes to be isentropic. For steady-state operation and kinetic and potential energy changes are negligible, and constant specific heat with Cp-1.023 kJ/kg.K. k=1.4 is used. Determine (i) the mass flow rate of air in the gas-turbine cycle, Gil) the rate of 2 total heat input, and (in) the thermal efficiency of the combined cycle.
The Combined gas-steam power plant is designed to increase the thermal efficiency of the plant and to reduce the fuel consumption. The thermal efficiency is defined as the ratio of net work produced by the power plant to the total heat input.
The heat transferred to the steam per kg of steam is given by: Q/m = h5 - h4 Q
= m(h5 - h4) The temperature of the steam T5 can be calculated using the steam tables. At a pressure of 15 MPa, the enthalpy of the steam h4 = 3127.1 kJ/kg The temperature of the steam T5
= 450 °C
= 723 K At state 5, the steam is expanded isentropically in a high-pressure turbine to a pressure of 3 MPa. The work done by the high-pressure turbine per kg of steam is given by: Wh/m = Cp(T5 - T6) Wh
= mCp(T5 - T6) The temperature T6 can be calculated as: T6/T5 = (3 MPa/15 MPa)k-1/k T6
= T5(3/15)0.4
= 533.16 K The temperature T5 can be calculated using the steam tables.
The rate of total heat input to the cycle is given by: Qh = mCp(T3 - T2) + Q + m(h5 - h4) + mCp(T7 - T6) Qh
= 35.046 × 1.023 × (977.956 - 698.54) + 35.046 × 728.064 + 30 × (3127.1 - 2935.2) + 30 × 1.023 × (746.624 - 533.16) Qh = 288,351.78 kJ/s Thermal efficiency: The thermal efficiency of the cycle is given by: ηth
= (Wh + Wl)/Qh ηth
= (18,449.14 + 22,838.74)/288,351.78 ηth
= 0.1426 or 14.26 % The mass flow rate of air in the gas-turbine cycle is 35.046 kg/s.The total heat input is 288,351.78 kJ/s.The thermal efficiency of the combined cycle is 14.26 %.
To know more about steam visit:
https://brainly.com/question/15447025
#SPJ11
Briefly describe the difference between a constant strain and linear strain triangular finite element. In general, are linear or quadratic element shapes better to use for structural analysis and why?
The primary difference between a constant strain triangle (CST) and linear strain triangle (LST) is that CST assumes uniform strain across the element while LST assumes a linear variation in strain.
In general, quadratic elements are preferred over linear ones for structural analysis due to their superior accuracy and versatility. Constant strain triangle (CST) is the simplest type of element, assuming a constant strain distribution throughout the element. This leads to less accurate results in complex problems. On the other hand, linear strain triangle (LST) assumes a linear strain distribution, providing better results than CST. Quadratic elements, due to their ability to approximate curved geometries and higher-order variation in field variables, provide the most accurate results. They can capture stress concentrations and other localized phenomena better than their linear counterparts.
Learn more about finite element analysis here:
https://brainly.com/question/13088387
#SPJ11
A bipolar transistor has an emitter transition region capacitance Cet of 3 pF at zero bias. With VBE = 0.65 V it has a total input capacitance C₁ of 30 pF with an Ic of 2 mA. Find C₁ when the collector current is increased to 12 mA. Take o = -0.8 V.
The total input capacitance C₁ becomes approximately 5.79 pF.
To find the value of C₁ when the collector current is increased to 12 mA, we can use the formula for the total input capacitance of a bipolar transistor:
C₁ = Cet + (Cπ / (1 - A * (VBE - VBE(on))))
where Cet is the emitter transition region capacitance, Cπ is the base-emitter capacitance per unit area, A is the current gain of the transistor, VBE is the base-emitter voltage, and VBE(on) is the threshold voltage.
Given:
Cet = 3 pF
C₁ = 30 pF (at Ic = 2 mA)
Ic1 = 2 mA
Ic2 = 12 mA
VBE = 0.65 V
VBE(on) = -0.8 V
First, we need to find the value of Cπ. We can use the relationship:
Cπ = C₁ - Cet
Cπ = 30 pF - 3 pF
Cπ = 27 pF
Now, we can calculate the value of C₁ when Ic = 12 mA using the formula mentioned earlier:
C₁ = Cet + (Cπ / (1 - A * (VBE - VBE(on))))
To find the value of A, we need to use the relationship:
A = Ic2 / Ic1
A = 12 mA / 2 mA
A = 6
Plugging in the values, we get:
C₁ = 3 pF + (27 pF / (1 - 6 * (0.65 V - (-0.8 V))))
Simplifying the expression inside the parentheses:
C₁ = 3 pF + (27 pF / (1 + 6 * 1.45 V))
C₁ = 3 pF + (27 pF / (1 + 8.7 V))
C₁ = 3 pF + (27 pF / 9.7 V)
C₁ = 3 pF + 2.79 pF
C₁ = 5.79 pF
Therefore, when the collector current is increased to 12 mA, the total input capacitance C₁ becomes approximately 5.79 pF.
to learn more about capacitance.
https://brainly.com/question/31871398
#SPJ11
Square loop with sides a and wire radius b: LA = 2μo a/π=[In (a/b) - 0.774]
A square loop with sides a and wire radius b: LA = 2μo a/π=[In (a/b) - 0.774]The given equation states that the inductance of a square loop of sides a and wire radius b can be determined as LA = 2μo a/π=[In (a/b) - 0.774].
Here, 'a' and 'b' represent the sides and the wire radius of the square loop respectively. LA represents the inductance of the square loop.The above formula can be used to calculate the inductance of a square loop. We can use this formula to find the value of the inductance of a square loop of given dimensions.Let's understand the concept of inductance before diving into the calculation of the formula.What is Inductance?Inductance is defined as the ability of a component to store energy in a magnetic field
.Inductance is the resistance of an electrical conductor to a change in the flow of electric current. It is the property of a conductor that opposes any change in the current flowing through it. The larger the inductance of a conductor, the more energy it can store in a magnetic field created by an electric current flowing through it.The inductance of a square loop of sides 'a' and wire radius 'b' can be determined using the given formula LA = 2μo a/π=[In (a/b) - 0.774].
To know more about radius visit:
https://brainly.com/question/13449316
#SPJ11
Question 1: Answer all questions Write any two important difference between friction wheel and gear. [1 mark] Question 2: Write a short note on gear drives giving their merits and demerits. 11.5 marks
Wheel and Gear Friction Wheel and Gear both are used to transmit power. Friction wheel is a simple device that is commonly used in low power applications. It is also known as a belt drive and can be found in home appliances such as washing machines, mixers, etc.
Friction wheels work by using the friction between the wheel and the belt to transmit power. On the other hand, gear drives are more commonly used in high power applications. Gears can be found in cars, trains, wind turbines, and many other machines. They transmit power by meshing together and transferring torque. Two important differences between Friction Wheel and Gear are: Friction wheels are easy to maintain while gears require more maintenance. Friction wheels are less expensive than gears.
Merits of Gear Drives:High efficiency: Gear drives have high efficiency as compared to other drives like belt drives.No slippage: Gear drives have no slippage, making them suitable for high power transmission and critical applications.Long life: Gear drives have a longer life than belt drives as they are made of metal. Hence they are more reliable and can be used for a longer duration of time. Smooth operation: Gear drives provide smooth operation as they don't slip and produce less noise.
To know more about transmit visit:
https://brainly.com/question/32340264
#SPJ11
An ideal Otto engine with an air compression ratio of 9 starts
with an air pressure of 90kpa and a temperature of 25 C. what is
the temperature after compression?
the temperature after compression is 2682 K. In an ideal Otto engine with an air compression ratio of 9 starts with an air pressure of 90kpa and a temperature of 25 C,
the temperature after compression can be determined using the ideal gas law. The ideal gas law is given as;PV=nRTWhere P is the pressure, V is the volume, n is the number of moles of the gas, R is the gas constant, and T is the temperature.In the problem above, we are interested in finding the final temperature (T2) after compression given initial conditions of pressure (P1)
temperature (T1) which are; P1 = 90 kPa and T1 = 25 °C = 298 K respectively. The air compression ratio is given as; r = 9. Therefore, the volume at the end of compression (V2) will be 1/9th of the initial volume (V1) that is;V2 = V1 / 9.From the ideal gas law, we have;P1V1 / T1 = P2V2 / T2Where;P2 = P1rV2 = V1/9Substituting the values gives;P1V1 / T1 = P1rV1 / 9T2 = T1r9T2 = 298 K x 9T2 = 2682 KT
To know more about temperature visit :-
https://brainly.com/question/14532989
#SPJ11
Why should we study dynamics?
How do we usually define space in dynamics?
How do we usually define space in dynamics?
What is force in dynamics?
Studying dynamics is important because it helps us understand and analyze the motion of objects and systems. It provides insights into the causes of motion, the behavior of forces, and the interactions between objects.
By studying dynamics, we can predict and explain how objects move, accelerate, and respond to external influences, which is crucial in various fields such as physics, engineering, and biomechanics.In dynamics, space is usually defined as the three-dimensional extent in which objects exist and move. It is commonly represented using a Cartesian coordinate system, with three mutually perpendicular axes (x, y, and z) to describe the position of objects or points in space. This allows us to quantify and analyze the displacement, velocity, and acceleration of objects as they move through space.
To know more about velocity visit :
https://brainly.com/question/18084516
#SPJ11
Determine the charge q developed when a piezoelectric crystal with A = 15 mm and h = 8 mm is subjected to a pressure p = 2 MPa if the crystal is (a) X-cut, length-longitudinal quartz (b) parallel-to-polarization barium titanate
Depending on the specific piezoelectric crystal used, the charge developed will vary.
Given:
- Piezoelectric crystal with A = 15 mm and h = 8 mm
- Pressure p = 2 MPa
- The crystal is (a) X-cut, length-longitudinal quartz (b) parallel-to-polarization barium titanate
(a) X-cut, length-longitudinal quartz:
- The charge developed in a piezoelectric crystal can be calculated using the formula q = d x A x p, where q is the charge, d is the piezoelectric coefficient, A is the surface area of the crystal, and p is the pressure applied.
- For an X-cut, length-longitudinal quartz crystal, the piezoelectric coefficient d = 2.04 x 10^-12 C/N.
- Substituting the values, we get q = (2.04 x 10^-12 C/N) x (15 mm x 8 mm) x (2 MPa) = 4.89 x 10^-6 C
(b) Parallel-to-polarization barium titanate:
- The piezoelectric coefficient for barium titanate is typically represented as e, which has a value of 1.9 x 10^-10 C/N.
- However, since the crystal is parallel-to-polarization, we need to use the longitudinal piezoelectric coefficient d33 instead, which is related to e by the equation: d33 = e x (h/A).
- Substituting the given values, we get d33 = (1.9 x 10^-10 C/N) x (8 mm / 15 mm) = 1.02 x 10^-10 C/N.
- Substituting the values into the formula for q, we get q = (1.02 x 10^-10 C/N) x (15 mm x 8 mm) x (2 MPa) = 2.45 x 10^-6 C.
- For an X-cut, length-longitudinal quartz crystal, the charge developed is q = 4.89 x 10^-6 C.
- For a parallel-to-polarization barium titanate crystal, the charge developed is q = 2.45 x 10^-6 C.
To know more about Piezoelectric crystals, visit:
https://brainly.com/question/29690670
#SPJ11
In the instant lottery with 30°, winning tickets, if x is equal to the number of winning tickets among n = 8 that are purchased, then the probability of purchasing two winning tickets is a 0.2965 b 0.2936 c 0.1488 d None of the other options
The correct option is None of the other options. Instant lottery with 30°, winning tickets is considered to calculate the probability of purchasing two winning tickets. Here, the total winning tickets are given by 30° and x represents the number of winning tickets that are purchased from n = 8.
Now, we have to calculate the probability of purchasing two winning tickets. Probability of purchasing two winning tickets can be calculated as,
P (X = 2) = $\frac{\binom{x}{2}\binom{30 - x}{6}}{\binom{30}{8}}$Where, $\binom{x}{2}$ represents the number of ways of choosing 2 winning tickets from x winning tickets.$\binom{30 - x}{6}$
[tex]P (X = 2) = $\frac{\binom{x}{2}\binom{30 - x}{6}}{\binom{30}{8}}$$\implies P(X=2)=\frac{\binom{x}{2}\binom{30-x}{6}}{\binom{30}{8}}$$[/tex]
[tex]\implies P(X=2)=\frac{x(x-1)\binom{30-x}{6}}{\frac{30 \cdot 29 \cdot 28 \cdot 27 \cdot 26 \cdot 25 \cdot 24 \cdot 23}{8 \cdot 7 \cdot 6 \cdot 5 \cdot 4 \cdot 3 \cdot 2 \cdot 1}}$$[/tex]
[tex]\implies P(X=2)=\frac{x(x-1)\cdot (30-x)(29-x)(28-x)(27-x)(26-x)(25-x)}{30 \cdot 29 \cdot 28 \cdot 27 \cdot 26 \cdot 25 \cdot 24 \cdot 23}$$\[/tex]
[tex]implies P(X=2)=\frac{x(x-1)(30-x)(29-x)(28-x)(27-x)(26-x)(25-x)}{(30 \cdot 29 \cdot 28 \cdot 27 \cdot 26 \cdot 25)^2}$$[/tex]
[tex]\implies P(X=2)=\frac{6! \cdot x(x-1)(30-x)(29-x)(28-x)(27-x)(26-x)(25-x)}{(30 \cdot 29 \cdot 28 \cdot 27 \cdot 26 \cdot 25)^2}$$[/tex]
[tex]\implies P(X=2)=\frac{6! \cdot x(x-1)(30-x)(29-x)(28-x)(27-x)(26-x)(25-x)}{30^8-30^7 \cdot x + 30^6 \cdot \binom{x}{2} - 30^5 \cdot \binom{x}{3} + 30^4 \cdot \binom{x}{4} - 30^3 \cdot \binom{x}{5} + 30^2 \cdot \binom{x}{6} - 30 \cdot \binom{x}{7} + \binom{x}{8}}$[/tex]
Now, substitute the given value of n = 8, and the total winning tickets are 30°, we have;
[tex]P (X = 2) = $\frac{\binom{8}{2}\binom{22}{6}}{\binom{30}{8}}$$\implies P(X=2)=\frac{\binom{8}{2}\binom{22}{6}}{\binom{30}{8}}$$[/tex]
[tex]\implies P(X=2)=\frac{28 \cdot 74613}{5852925}$$\implies P(X=2)=\frac{2090644}{5852925}$$\implies P(X=2) \approx 0.35691$[/tex]
Therefore, the probability of purchasing two winning tickets is 0.35691, which is not available in the given options.
To know more about probability visit:-
https://brainly.com/question/31828911
#SPJ11
Question 1: Design a linkage system such that as a float for liquid level measurement moves from 0 to 1 m, an LVDT core moves over its linear range of 3 cm. Question 2: A pressure transducer outputs a voltage to a readout device that converts the signal back to pressure: The device specifications are: Resolution: 0.1 psi Sensitivity error: 0.1 psi Linearity error: within 0.1% of reading Drift: less than 0.1 psi/6 months (32-90F) The transducer has a claimed accuracy of within 0.5% of reading. For a nominal pressure of 100 psi at 70F, estimate the design-stage uncertainty in a measured pressure.
When a float is present for the measurement of liquid level moving from 0 to 1 m, the LVDT core moves over its linear range of 3 cm. The float will be attached to the end of the linkage system so that the float moves from 0 to 1 m, and the LVDT core moves over its linear range of 3 cm.
The system will be designed in such a way that the float moves in a linear manner from 0 to 1 m. The linkage system is shown below: Let the float be situated at the beginning of the linkage system and the LVDT core be located at the end of the linkage system.
The length of the linkage system is defined by the float movement range (0-1 m). We must adjust the lengths of the links to achieve a LVDT core movement range of 3 cm. The float will be attached to the first link of the linkage system, which will be a straight link, as shown in the figure above.
To know more about measurement visit:
https://brainly.com/question/28913275
#SPJ11