suppose that the frequency f of the current in an ac circuit goes to zero (which means that the current becomes a direct current). which circuit element would not permit charge to flow in the circuit?

Answers

Answer 1

A capacitor, because it has the greatest reactance at frequency f = 0 Hz.

A capacitor is a device that stores electrical energy in an electric field through the accumulation of electrical charges on two nearby surfaces insulated from each other. It has two terminals and is a passive electrical component. Charges flow through the capacitor when it is supplied with electricity, but this flow is blocked by the insulation between the metal plates. Since the capacitor's electrode plates are separated by an insulator (air or dielectric), no direct current can flow unless the insulator decays. In other words, a capacitor blocks direct current. When we connect a capacitor across an AC power source, it starts charging and discharging continuously due to the continuous change in the supply voltage. Capacitors do not store charge. Capacitors actually store a charge imbalance.

To learn more about capacitors click here https://brainly.com/question/17176550

#SPJ4


Related Questions

a .50 kilogram puck is sliding on a horizontal shuffle board court is slowed to rest by a frictional force of 1.2 newtons what is the coeffivent of kinetic friction betweej the puck and the surface of the shuffle board court

Answers

The puck's kinetic friction coefficient only with shuffleboard court's surface is 0.24.

How does kinetic friction work?

It is known as a force that exists between moving surfaces as kinetic friction. A force that operates in the opposing direction to the motion of a body on the surface is felt. The percentage of kinetic friction of the two materials will determine the size of the force.

Briefing:

Given  ,The mass of puck is, m = 0.50 kg.

The magnitude of frictional force is, f = 1.2 N.

The force which tends to oppose the motion between an object and the surface is known as frictional force. And its value is,

F= μ × mg

here,   is the coefficient of kinetic friction between the puck and the surface of the shuffleboard court.

Solving as ,

1.2 = u × 0.50 × 9.8

 μ =  [tex]\frac{1.2}{0.50 . 9.8}[/tex]

 μ = 0.24

Thus, we can conclude that the coefficient of kinetic friction between the puck and the surface of the shuffleboard court is 0.24.

To know more about  kinetic friction visit:

https://brainly.com/question/23295976

#SPJ4

the role of the mouth in sound the prodution of sound during speech or singing is a complicated process lets concentrate on the mouth a typcal depth for the huamn mouth is about 8 cm although this number can vary. (Check it against your own mouth.) We can model the mouth as an organ pipe that is open at the back of the throat. What are the wavelengths and frequencies of the first four harmonics you can produce if your mouth is (a) open, (b) closed? Use .v=354 m/s

Answers

When open mouth the wavelengths and the frequencies of the first four harmonics you can produce are 0.16 m and 2,212.5 Hz, 0.08 m and 4,425 Hz,  0.053 m and 6,637.5 Hz, 0.04 m and 8,850 Hz.

When closed mouth the wavelengths and the frequencies of the first four harmonics you can produce are 0.32 m and 1,106.25 Hz, 0.1067 m and 3,318.75 Hz, 0.064 m and 5,531.25 Hz, 0.0457 m and 7,743.75 Hz.

If we open our mouth it will create a tube that opens at both ends.

The wavelength
[tex]\lambda = \frac{2L}{n}[/tex]
L = the length of a tube (m) = 8 cm = 0.08 m
λ = the wavelength (m)
n = 1, 2, 3, 4, 5, ...The frequency
f = v ÷ λ
v = the speed of the sound (m/s)
f = the frequency (Hz)

For the first harmonic

[tex]\lambda_1 = \frac{2L}{1}[/tex]
λ₁ = 2 × 0.08 = 0.16 mf₁ = v ÷ λ₁ = 354 ÷ 0.16
f₁ = 2,212.5 Hz

For the second harmonic

[tex]\lambda_2 = \frac{2L}{2}[/tex]
λ₂ = 0.08 mf₂ = v₂ ÷ λ₂ = 354 ÷ 0.08
f₂ = 4,425 Hz

For the third harmonic

[tex]\lambda_3 = \frac{2L}{3}[/tex]
λ₃ = 2 × 0.08 m ÷ 3
λ₃ = 0.053 mf₃ = v₃ ÷ λ₃ = 354 ÷ 0.053
f₃ = 6,637.5 Hz

For the fourth harmonic

[tex]\lambda_4 = \frac{2L}{4}[/tex]
λ₄ = 0.08 m ÷ 2
λ₄ = 0.04 mf₄ = v₄ ÷ λ₄ = 354 ÷ 0.04
f₄ = 8,850 Hz

If we closed our mouth it will create a tube that one end opens and the other end closed.

The wavelength
[tex]\lambda = \frac{4L}{2n-1}[/tex]
n = 1, 2, 3, 4, ...The frequency
f = v ÷ λ

For the first harmonic

[tex]\lambda_1 = \frac{4L}{1}[/tex]
λ₁ = 4 × 0.08 = 0.32 mf₁ = v ÷ λ₁ = 354 ÷ 0.32
f₁ = 1,106.25 Hz

For the second harmonic

[tex]\lambda_2 = \frac{4L}{3}[/tex]
λ₂ = 4 × 0.08 m ÷ 3
λ₂ = 0.1067 mf₂ = v₂ ÷ λ₂ = 354 ÷ 0.1067
f₂ = 3,318.75 Hz

For the third harmonic

[tex]\lambda_3 = \frac{4L}{5}[/tex]
λ₃ = 4 × 0.08 m ÷ 5
λ₃ = 0.064 mf₃ = v₃ ÷ λ₃ = 354 ÷ 0.064
f₃ = 5,531.25 Hz

For the fourth harmonic

[tex]\lambda_4 = \frac{4L}{7}[/tex]
λ₄ = 4 × 0.08 m ÷ 7
λ₄ = 0.0457 mf₄ = v₄ ÷ λ₄ = 354 ÷ 0.0457
f₄ = 7,743.75 Hz

Learn more about frequency in a tube here: https://brainly.com/question/29491212

#SPJ4

did a large terrestrial planet ever form in the region of the asteroid belt? (a) no, because there was never enough mass there. (b) no, because jupiter prevented one from accreting. (c) yes, but it was shattered by a giant impact.

Answers

The large terrestrial planet never formed in the region of the asteroid belt because there was never enough mass there. Thus, option (a) is the answer.

Rocky planetesimals survived in the asteroid belt between Mars and Jupiter because they did not accrete into a planet. Jupiter's gravity, through the influence of orbital resonances, stirred up asteroid orbits and thereby prevented their accretion into a planet.

Jupiter's gravity is so strong, that it makes asteroid orbits within the Kirkwood gaps unstable. It's these gaps that prevented a single planetary body from forming in that region. So, because of Jupiter, asteroids formed into families of debris, rather than a single planetary body.

To know more about Asteroid Belt:

https://brainly.com/question/13155353

#SPJ4

two wires have the same length, but the second has twice the diameter of the first. find the resistance of the second wire if the resistance of the first is 4ω.

Answers

2ω is the resistance of the second wire if the resistance of the first is 4ω if two wires have the same length, but the second has twice the diameter of the first.

R= 4ω.

R = ρl/A

2d=r

R2=2ω

Resistance is the capacity of a conductor to obstruct the passage of an electric current through it. It is controlled by the interaction of the applied voltage and the electric current passing through it.

Conductors have very little resistance, whereas insulators have a significant amount of resistance. The resistance increases as the current flow decreases. Resistance is influenced by the properties and dimensions of the material (area of cross section)

To know more about  resistance visit : brainly.com/question/14547003

#SPJ4

a student runs an experiment in which a block of known mass is moving across a horizontal table in an xy-coordinatexy-coordinate plane. as the block reaches the origin of the coordinate system, the block explodes into two pieces of masses m1m1 and m2m2. during the experiment, the velocity of the block 1.01.0 second before the explosion and the velocity of the two pieces 1.01.0 second after the explosion are measured using a motion sensor. conservation of momentum is applied using the masses of the two pieces. however, when the velocity of the piece of mass m2m2 is calculated, the measured value is 10% less than the calculated value. which of the following statements best explains the difference in the calculated and measured velocity?

Answers

Question is incomplete the complete question is:

A student runs an experiment in which a block of known mass is moving across a horizontal table in an xy-coordinate plane. As the block reaches the origin of the coordinate system, the block explodes into two pieces of masses m1 and m2. During the experiment, the velocity of the block 1.0 second before the explosion and the velocity of the two pieces 1.0 second after the explosion are measured using a motion sensor. Conservation of momentum is applied using the masses of the two pieces. However, when the velocity of the piece of mass m2 is calculated, the measured value is 10% less than the calculated value. Which of the following statements best explains the difference in the calculated and measured velocity?

A) As the block is moving across the table, friction will affect the block’s motion and thus could account for the difference.

B) It is possible that a small amount of the original block was lost during the explosion.

C) When the student did the calculation, the student assumed that the explosion occurred just as the block reached the origin. The difference in velocity could be due to the explosion occurring either just before or just after the origin.

D) The explosion created a force that affected the experiment.

E) Conservation of momentum is not the correct equation to apply to the explosion, since the two pieces apply forces to each other.

The correct explanation will be as the block is moving across the table, friction will affect the block’s motion and thus could account for the difference.

What is friction?

Moving things lose energy and slow down due to the friction force that resists their motion. A fluid, like air or water, exerts a frictional force on moving objects when they travel through it. A fluid's frictional force is referred to as a drag force.

Effect of friction on motion?

An opposing force to the relative motion of two objects is friction. You will be researching kinetic friction for this assignment (also called sliding friction). Kinetic friction is the process by which some of the kinetic energy of motion between two objects is transformed into heat. The same thing happens when two objects are sliding past one another-for example, when you push a box across the floor.

To know more about Friction visit:

https://brainly.com/question/28356847

#SPJ4

the left end of a long glass rod 9.00 cmcm in diameter, with an index of refraction 1.56, is ground and polished to a convex hemispherical surface with a radius of 4.50 cmcm . an object in the form of an arrow 1.49 mmmm tall, at right angles to the axis of the rod, is located on the axis 23.0 cmcm to the left of the vertex of the convex surface.Find the position and height of the image of the arrow formed by paraxial rays incident on the convex surface. Is the image erect or inverted?

Answers

S' = 14.77 cm height of image = 0.577 mm is the computed response. It is inverted because magnification is negative.

Where radius (R) is positive because it is facing the same direction as the refracted light, and index of refraction (n1) = 1 for air and index of refraction for glass (n2) = 1.60, object distance from vertex to spherical surface (s) is 24 cm, or 0.24 meters, and image distance from vertex to spherical surface (s') is 4 cm, or 0.04 meters.

Height of object = y = 1.5 mm = 0.0015 m Height of image = y'

For a spherical reflecting surface, the object-image formula is:

According to the magnifying formula:

It is inverted because magnification is negative.

Learn more about refraction here-

https://brainly.com/question/14760207

#SPJ4

True or False. When light passes from one medium to another the speed stays constat

Answers

When light passes from one medium to another the speed of the light changes. Therefore, the given statement is false.

What is refraction?

Refraction takes place when the light travels from one medium to another medium it changes its speed. Refraction can be defined as the redirection of light as it passes from one medium to another.

The redirection of the light ray causes by the change in the speed of the wave or by a change in the medium. Refraction of light can be observed for sound waves and water also experiences refraction.

Refraction of light obeys Snell's law, according to which the ratio of the sines of the angle of incidence and angle of refraction must be equal to the ratio of the refractive indices of the two media.

[tex]{\displaystyle {\frac{Sin \theta_1}{Sin \theta_2} =\frac{n_2}{n_1}[/tex]

Learn more about refraction, here:

brainly.com/question/14760207

#SPJ1

a skydiver leaps from a plane and accelerates toward the surface of the earth. earth’s acceleration toward the skydiver is:

Answers

Skydiver's acceleration is substantially greater than Earth's acceleration in its direction.

What is acceleration?

The rate at which velocity, measured in terms of speed and direction, changes over time is known as acceleration. Anything is said to have been accelerated when it goes faster or slower in a straight line.

You fall, your descent to the ground quickening. Until the drag from her falling speed due to wind resistance equals the acceleration induced by gravity, this acceleration will continue. Because air resistance, sometimes referred to as drag force, is typically far lower than the normal force of a body, he should continue to accelerate downward. When these forces are balanced, she will attain "terminal velocity," at which point she will cease gaining speed.

He will continue to descend until he opens his chute at the same pace, although the acceleration he experiences at first is due to gravity.

To know more about acceleration use link below:

https://brainly.com/question/16710160

#SPJ4

what is the wavelength of the electromagnetic wave produced by your cell phone, if the frequency of that wave is 900 mhzmhz ? express your answer with the appropriate units.

Answers

The wavelength of the electromagnetic wave is 0.33m

The study of electromagnetic radiation is known as electrodynamics, and electromagnetic radiation itself, or EM, is a physical phenomenon connected to the idea of electrodynamics. The properties of superposition apply to electric and magnetic fields as well. A field produced by a specific particle or a time-varying magnetic or electric field, then, contributes to the other fields that are present in the same space due to other causes. In addition, all magnetic and electric field vectors combine together using the vector addition formula because they are vector fields. For instance, in optics, two or more coherent light waves may interact and, through destructive or constructive interference, produce a resultant irradiance that is different from the sum of the component irradiances of the individual light waves.

Frequency = 900 x 10⁶Hz

[tex]Frequency=speed/wavelength[/tex]

[tex]Wavelength=speed/frequency[/tex]

=3 x 10⁸/900 x 10⁶

=0.33m

To study about coherent light -

https://brainly.com/question/9964433

#SPJ4

a wheel 0.800 m in diameter rotates with an angular acceleration of 4.40 rad/s2. if the wheel’s initial angular velocity is 2.10 rad/s, what is its angular velocity after 11.4 s?

Answers

The angular velocity after 11.4s is 52.56 rad/s

[tex]w_{f}=w_{0}+at[/tex]

Given:[tex]w_{0}=2.10,a=4.40,t=11.4[/tex]

[tex]w_{f}=2.10+4.40*11.4\\w_{f}=52.56[/tex]

What is angular velocity?
Angular velocity
is a vector quantity and is described as the rate of change of angular displacement which specifies the angular speed or rotational speed of an object and the axis about which the object is rotating.

What are angular velocity and acceleration?
Angular velocity is the rate of change of angular displacement and angular acceleration is the rate of change of angular velocity.

Are angular velocity and momentum the same?
While linear momentum is P = MV, where M is mass and V is velocity, angular momentum L = Iw, where I is rotational inertia and w (we use w instead of small Omega, the conventional symbol) is angular velocity. Angular velocity is just the angle the mass rotates in an interval of time. w has the units of radians/second.

Thus, the angular velocity is 52.56 rad/s

To know more about angular velocity:
https://brainly.com/question/20432894
#SPJ4

According to the one-year calendar model based on the Big Bang theory, life on the planet began in __________.
December
August
January
September

Answers

According to the one-year calendar model based on the Big Bang theory, life on the planet began in August.

About Big Bang Theory

The Big Bang theory is the most recent conjecture for the creation of the universe. The big explosion that occurred 13.7 billion years ago is believed to be the beginning of the journey of the entire universe.

The big bang theory describes the creation of the universe as an expansion of matter which then exploded like a giant balloon that is constantly being filled with air. The remnants of these explosions then each became the seeds for the formation of galaxies, solar systems, and the various objects that fill them.

Revealed, Dark Energy in the Universe in Cosmology

Cosmologists and physicists call the universe currently expanding as a result of the Big Bang explosion. Even the speed of its expansion is believed to continue to increase.

Scientists have also found predicted thermal signatures from the Big Bang, the cosmic microwave radiation that enveloped the universe. In the thermal traces there are no objects older than 13.7 billion years, indicating that the universe was born around that time (the time of the Big Bang phenomenon).

The traditional Big Bang theory holds that the universe began from a singularity, or point of infinite density and temperature whose properties are difficult for the human mind to comprehend.

But the theory does not accurately describe anything obvious, because the singularity idea is based on Einstein's general theory of relativity.

Learn more about big bang theory at https://brainly.com/question/17209127.

#SPJ4

according to this graph, the minimum size of an object that could cause a mass extinction is a little less than _____

Answers

According to this graph, the minimum size of an object that could cause a mass extinction is a little less than  10 km.

Answer is in the graph, min size of object that could cause a mass exinction is a little less than 10 km.

When a significant portion of biodiversity, such as separate species of bacteria, fungi, plants, mammals, birds, reptiles, amphibians, fish, or invertebrates, goes out during a brief period of geological time, this is referred to as a mass extinction. Impacts from comets and asteroids, extensive volcanism, climate changes,bacteria,abrupt shifts in the topography and ocean currents, or a combination of these elements may be the cause of mass extinction events. At least 75 percent of all species become extinct during major extinctions, which typically last three million years. Some experts think that, if things continue as they are, we may be able to remove that number within a few centuries.

Learn more about mass extinction here:

https://brainly.com/question/10297522

#SPJ4

A friend asks you how much pressure is in your car tires. You know that the tire manufacturer recommends 30 psi, but it’s been a while since you’ve checked. You can’t find a tire gauge in the car, but you just finished taking physics and so you tell your friend, "I don’t know, but I can figure it out." From the owner’s manual you find that the car’s mass is 1700 kg . It It seems reasonable to assume that each tire supports one-fourth of the weight. Using a ruler, you find that the tires are 16 cm wide and the flattened bottom segment of the tire is 15 cm long. Your observation of the tire tread pattern suggests that two-thirds of this segment is in actual contact with the road.
What answer—in psi—will you give your friend?

Answers

To calculate the pressure in the car tires, we can use the equation $P = \frac{F}{A}$, where $P$ is the pressure, $F$ is the force acting on the area, and $A$ is the area over which the force is applied. In this case, the force acting on the tire is the weight of the car, and the area is the portion of the tire that is in contact with the road.

First, we need to calculate the weight of the car. The weight of the car is given by the equation $W = mg$, where $m$ is the mass of the car and $g$ is the acceleration due to gravity. We are given that the mass of the car is 1700 kg, so the weight is $W = 1700 \text{ kg} \times 9.8 \text{ m/s}^2 = 16786 \text{ N}$.

Next, we need to calculate the force acting on each tire. Since the weight of the car is distributed evenly among the four tires, each tire supports one-fourth of the total weight, or $F = \frac{1}{4} \times 16786 \text{ N} = 4196.5 \text{ N}$.

Now we need to calculate the area of the tire that is in contact with the road. The width of the tire is 16 cm, and we are given that two-thirds of the flattened bottom segment is in contact with the road.

This means that the length of the segment in contact with the road is $\frac{2}{3} \times 15 \text{ cm} = 10 \text{ cm}$. The area of the tire in contact with the road is therefore $A = 16 \text{ cm} \times 10 \text{ cm} = 160 \text{ cm}^2$.

Finally, we can use the equation $P = \frac{F}{A}$ to calculate the pressure in the tires. Plugging in the values for the force and the area, we get

$$P = \frac{F}{A} = \frac{4196.5 \text{ N}}{160 \text{ cm}^2} = 26.2 \text{ Pa}$$

Since 1 psi is equivalent to 6894.757 Pa, the pressure in the tires is approximately

Learn more about pressure in the tires:
https://brainly.com/question/29404730

#SPJ4

52 Points HELP
An arrow leaves a bow at an anitial velocity of 47.74m/s. 0.5 seconds after leaving the bow. When the arrow reaches the target its final velocity is 68.58m/s, 5 seconds later. what is the acceleration of the arrow

Answers

27.5 m/s. If the average force exerted on the arrow by the bow was increased 3 times and the arrow was accelerated over the same distance

what magnitude of current is required to produce 1.4 kg of sodium metal in one hour? express your answer in amperes to two significant figures.

Answers

Magnitude of current required is 1630 amp.

Current can be defined as the rate of flow of charge.

Since Faraday represents the magnitude of electric charge per mole of the electron

Mass can be given as:

mass = molar mass * faradays used/faradays needed

1 faraday = 1C/96500

Na + (aq) + e- -> Na(s) : one electron is transferred so faradays needed to produce 23.0g Na is 1

1.4kg*1000 = 1400g

1400g = 23.0g/mol * Fu/1f

Fu (faradays used) = Coulombs/96500 (faraday constant)

Fu = 60.9f=Q/96500

Q = 96500*60.9= 5.88*10^6

As we know that, Q = I*t

5.88*106= I*3600s(1h=60min=3600s)

I=1630amps

The current required to produce 1.4 kg of sodium metal in one hour is 1630 amperes.

To know more about current,

https://brainly.com/question/14981710

#SPJ4

suppose identical amounts of heat transfer into different masses of mercury and water, causing identical changes in temperature. what is the ratio of the mass of mercury to water?

Answers

Assume that similar quantities of heat are transferred into various masses or mercury and water, resulting in equivalent temperature variations. Mercury's mass is 0.033 times that of water.

What makes Mercury so unique?

Of such eight moons of jupiter, Mercury is the smallest and one that is closest to the Sun. Mercury completes three spins of its axis for each of the two circuits it makes around the Sun, so takes around 96 Earth days. This rotation is exclusive to the solar system and is gravitationally locked.

Briefing :

According to the statement we have Mass of mercury = M(Hg), and

Mass of Water = M(H₂O)

M(cu) / M(H₂O) , heat transfer and mass are related as we have the formula : Q=mcΔT

according to the formula we have , Q(Hg) = M(Hg) C(Hg)ΔT(Hg)...........(1)

for water ,  Q(H₂O)= M(H₂O) C(H₂O)ΔT(H₂O)..............................(2)

therefore dividing by specific heat in the temperature = C T from both sides .

we Get :      [tex]\frac{ Q(Hg)}{CT} =[/tex][tex]\frac{ M(Hg) C(Hg)ΔT(Hg)}{CT}[/tex] , [tex]\frac{Q(H2O) }{CT} =[/tex] [tex]\frac{C(H2O) Δ TH2O}{CT}[/tex]

∴ Q(Hg)=[tex]\frac{Q(Hg)}{Q(Hg)ΔT(Hg)}[/tex]  ,    Q(H₂O)= [tex]\frac{ Q(H2O)}{C(H2O)ΔTH2O)}[/tex]

      by solving we get = Q(Hg)/C(Hg)ΔT(Hg)/Q(H₂O) / C(H₂O)ΔT(H₂O)

= Q(Hg)/C(Hg)ΔT(Hg) × C(H₂O)ΔT(H₂O)/Q(H₂O)

= [tex]\frac{C(H2O)}{C(Hg)}[/tex]= M(Hg)/M(H₂O)

specific heat of water = 4184 J/kg

and specific heat of mercury = 139 J/kg

therefore we get 4184/139 = 0.033 ans or  3:100 in ratio

To know more about Mercury visit :

https://brainly.com/question/594092

#SPJ4

if an astronaut knocks a wrench off the outside of the space shuttle (while in space) while she is doing a repair job, the wrench will continue moving in the same direction. which of newton's laws of motion will the wrench demonstrate?

Answers

The Newton's first law is demonstrated over here.

If the wrench is thrown then that wrench will keep on moving in the space.

As we all no space has no gravity and since there is no gravity, hence, no force is applied on that body.

The wrench will move freely in the space and will continue to move in same direction until there is some external force is applied to stop or change its direction.

This shows that over here the Newton's first law is applied.

The Newton's first law states that the body will continue to be in the same state or motion and will not change until the external force is applied on it.

This Newton's first law is also known as law of inertia.

Therefore, the wrench will continue to move in the same direction under the influence of Newton's first law.

To know more about Newton's first law, refer: brainly.com/question/974124

#SPJ4

suppose you found a star with the same mass as the sun moving back and forth within a period of 16 months. a) what could you conclude? b) explain the reasons for your conclusion scientifically.

Answers

It has a planet orbiting at a distance larger than 1 AU when you discover a star that rotates back and forth every 16 months and has the same mass as the sun.

How can a planet's orbit move inward due to a gravitational collision?

How can a planet's orbit move inward due to a gravitational collision? Another object receives both energy and angular momentum from it.

Which of the following is true regarding the transit method of finding exoplanets?

There are two fundamental obstacles to directly finding exoplanets. One is that as we go farther away from the earth, the angular size of planets decreases and is no longer able to be resolved in a picture.

To know more about gravitational collision visit:-

https://brainly.com/question/5795500

#SPJ4

how much tension must a rope have if it is used to support a precious painting with a mass of m on a smooth, frictionless surface, inclined at an angle 6 with respect to the horizontal ground?

Answers

The tension must a rope have to support a certain mass with horizontal is 1.3671N.

A vertically twisted rope moves more quickly downward and more slowly upward. It needs the rope to exert a force with a tangential component in order to whirl it at a constant speed.Since we are working with idealized pulleys and strings, the mass m1 is ultimately connected to the axle of the movable pulley P1 dot.Due to the fact that a massless pulley can have no net force, pulley P1 has upward tension T1 and downward tension 2T1 dot.    2T1−T1=0 .We then move to pulley P2, which has an upward tension of 2T1, and that is seen to be zero. This equation can only be true if T1=0. Thus, the mass m2 under tension is also zero. In conclusion, there is no tension in the rope.

T=mgsinФ

T=0.5 x 9.8 x sin6

=4.9sin6

=4.9 x 0.279

=1.3671N

To study more on  tension -

https://brainly.com/question/14294135

#SPJ4

If the weight of an object of mass "m" is "mg," then the weight of an object of mass "2m" is.

Answers

This leads us to the conclusion that if an object of mass "m" weighs "mg," then an object of mass "2m" weighs "2mg."

Which is mass?

Mass is a crucial aspect of all matter and a measurement on inertia in physics. What a body of matter is fundamentally, is the resistance it offers to something like a change in its speed and location brought on by the application of a force. The amount of mass a body has no bearing on how much of a change a force applies.

what do a mass and weight mean?

Mass is a unit used to describe the amount of matter who makes up an object. Weight, a measure of force, is used to calculate the gravitational pull an object experiences. In contrast to mass, weight is not location-dependent.

To knwo more about mass visit:

https://brainly.com/question/19694949

#SPJ4

the acceleration due to gravity on the surface of the moon is about 1/6 that on the surface of earth. an astronaut weighs 600 n on earth. the astronauts mass on the moon is most nearly:

Answers

Mass of the astronaut on the moon is 61.22 because the acceleration due to gravity on the surface of the moon is about 1/6 that on the surface of earth.

Gravitational acceleration is the acceleration gained by an object due to the force of gravity.

Its SI unit is m/s².It has both magnitude and direction, so it is a vector quantity. Gravitational acceleration is represented by g. The standard value of g on the earth's surface at sea level is 9.8 m/s².

Weight of the astronaut on the Earth = w = 600 N

Mass of the astronaut on the Earth = w/g

Mass m = 600/9.8

m = 61.22 kg

Mass of the astronaut will remain same on the Moon but the weight will change due to the change in the acceleration due to gravity on the surface of the moon.

Acceleration due to gravity on the surface of the moon is about 1/6 that on the surface of earth i.e. g' = g/ 6

g' = 9.81/6

g' = 1.63

Weight of the Astronaut on the surface of the moon = m * g'

W' = 100.094 N

Mass will be 61.22 kg and the weight will be 100.94 N on the surface of the moon.

To know more about acceleration due to gravity,

https://brainly.com/question/28084833

#SPJ4

study smarter the plutonium isotope 239pu has a half-life of 24,000 years and decays by the emission of a 5.2 mev alpha particle. plutonium is not especially dangerous if handled because the activity is low and the alpha radiation doesn't penetrate the skin. however, there are serious health concerns if even the tiniest speck of plutonium is inhaled and lodges deep in the lungs. this could happen following any kind of fire or explosion that disperses plutonium as dust.

Answers

Therefore, the number of ²³⁹Pu atoms in 1.0 mm diameter particle is  2.6*10⁷

The half-life of the  is  ²³⁹Pu=2400 yrs

The radius of soot particles is r =1*10⁻⁶m/0=0.5*10⁻⁶m

The density of Plutonium is  ρ=19800kg/m³

The number of   ²³⁹Pu atoms in a  diameter particle is

N=(m/Ma)Na

=ρ4πr³Na/3Ma

Substitute the given values to get number of atoms in particle

N=19.8*4π*(0.5*10⁻⁶)³*6.02*10²³/3*239*10⁻³

=2.6*10⁷

Learn more about atoms here:

https://brainly.com/question/19937820

#SPJ4

as long as an object is not gaining or losing mass, a net force on the object will cause a change in as long as an object is not gaining or losing mass, a net force on the object will cause a change in velocity. weight. speed. acceleration. direction.

Answers

The net force would cause the velocity of the body to change and it would accelerate.

What is the net force?

We know that the force that is acting on a body is a vector quantity. If the force is a vector quantity, the implication of this is that the force would have both a magnitude and direction.

According to the Newton first law of motion, if an object is acted upon by an unbalanced force, the result of this is that the velocity of the object would change and the object would accelerate.

Learn more about net force:https://brainly.com/question/18109210

#SPJ1

A soccer ball is kicked horizontally. what is the average speed if its displacement is 21 m after 4 sec

Answers

When a soccer ball is kicked horizontally, then the average speed is calculated to be 5.25 m/s.

What is displacement?

The term displacement means that an object has moved, or has been displaced. Change in position of an object is displacement. Standard unit of displacement in the International System of Units is meter. Displacement is usually measured along a straight line

Distance is a scalar quantity that refers to how much ground an object has covered during motion whereas displacement is a vector quantity that means how far out of place an object is.

Given displacement is 21m

and time = 4sec

Therefore average speed= 21/4

= 5.25 m/s

To know more about displacement, refer

https://brainly.com/question/14422259

#SPJ4


Question 8 of 25
**
force of friction and air resistance
normal contact force from the road
driving force from the engine
weight of the car
Hide score
The diagram below shows the different forces acting on a car. Which label below the diagram goes
with arrow A?
off
Reduce contrast
D
7✔ 100%
74%
1007
NICE

Answers

Answer:

Explanation:

The diagram shows four forces acting on a plane in flight. direction of flight. (b) (i). Which arrow represents air resistance?

dirk pushes on a packing box with a horizontal force of 75.0 n as he slides it along the floor. the average friction force acting on the box is 5.0 n. how much total work is done on the box in moving it 2.50 m along the floor?

Answers

Total work done to be done on the box in moving it 2.50 m along the floor is 175 j.

Friction force is an opposing force of motion. It comes into play when an object moves over the surface of another object.

We can find the friction force using formula,

[tex]F_{friction[/tex] = µ • [tex]F_{normal[/tex]

Where,

[tex]F_{friction[/tex] = friction force

µ  = coefficient of friction

[tex]F_{norm[/tex] = normal force.

In question given is

Horizontal force(F)  = 75 N

Average friction force (f)  = 5.0 N

displacement = 2.50 m

[tex]F_{net[/tex] = F-f

      = 75- 5 N = 70 N

Work done by the force is

W = [tex]F_{net[/tex] × S

  = 70 × 2.50 j

  = 175 j

To know more about work here

brainly.com/question/21724760

#SPJ4

what is the classification of bodies like pluto and eris, which are large enough to be round and have orbits beyond neptune? why are they not considered to be planets?

Answers

Given their position, Pluto , Eris are sometimes known as trans-Neptunian objects and dwarf planets (TNOs).

A dwarf planet outside of Neptune's orbit is referred to as a plutoid. As a result of their small size and extremely frigid surface temperatures, Plutoids are also sometimes referred to as "ice dwarfs." One of our solar system's largest dwarf planets is Eris. Despite being three times farther from the Sun, it is roughly the same size as Pluto.

Pluto was downgraded to a dwarf planet by the International Astronomical Union (IAU) because it did not meet the three requirements for a full-sized planet. In essence, Pluto satisfies all the requirements save for the fact that it "has not cleared its neighboring region of other objects."

For more information on dwarf planets

https://brainly.com/question/2274077

#SPJ4

6. A bird drops a feather from the roof of a 13.1 m tall building. The feather is blown
48.6 m west before falling to the ground. What is the resultant displacement of
the balloon?

Answers

The resultant displacement of the feather  be 50.33 m.

What is displacement?

The term "displacement" refers to a shift in an object's position. It is a vector quantity with a magnitude and direction. The symbol for it is an arrow pointing from the initial location to the ending place.

For instance, if an object shifts from location A to position B, its position changes. Displacement is the term used to describe this shift in an object's position.

Given that: A bird drops a feather from the roof of a 13.1 m tall building. The feather is blown 48.6 m west before falling to the ground.

So,  the resultant displacement of the feather  be = √(13.1² + 48.6²) m = 50.33 m.

Learn more about displacement here:

https://brainly.com/question/11934397

#SPJ1

in comparing two unequal forces on a rigid body, is it possible to have the larger force produce less torque than the smaller force?

Answers

Yes, it is feasible for the larger force to induce less torque than smaller force when two unequal forces are applied to a rigid body.

What exactly is contact force?

Objects making contact each other exert a force on one another known as contact force. The region of direct contact of two objects is where the contact force acts. This force may be brief in the guise of an impulse or it may be continuous as both a continuous force. Newton's Law covers contact force.

Briefing:

Torque = rFsin(θ)

It is feasible for a larger force to generate less torque than a smaller force if it acts at a closer distance than that of the smaller force.

To know more about Force visit:

https://brainly.com/question/14110395

#SPJ4

a child sprays her sister with water from a garden hose. the water is supplied to the hose at a rate of 0.123 l/s, and the diameter of the nozzle is 5.43 mm. at what speed ???? does the water exit the nozzle?

Answers

The water exists the nozzle at the speed of 5.315 m/s when rate of flow and diameter is given.

What is the  water flow rate?

Your water flow rate is the measurement of how many gallons of water could potentially come out of your kitchen faucet or bathtub per minute.

Given, Rate of flow= 0.123 l/s = 0.000123 m^3/s

and d= 5.43 mm= 0.00543m

r= 2.715 * 10^-3

Flow rate= water velocity * area of the nozzle

Area of nozzle = π* r²

= 3.14 *( 2.715 * 10^-3)²

= 2.314 * 10^-5

0.000123 = V * 2.314 * 10^-5

Speed at which the water exits= 5.315 m/s

To know more about rate of flow, refer

https://brainly.com/question/22716530

#SPJ1

Other Questions
Point A lies at 6 on an number line and is dilated usingthe origin as the center with scaling factor of 5/2. Atwhat location does its image lie on the number line?O 18O 15O2225 what is the approximate mole fraction of ethanol, c2h5oh, in an aqueous solution in which the ethanol concentration is 11.0 molal? utilizing the world health organization (who) framework of clinical categories for persons with acquired immunodeficiency syndrome (aids) over 15 years of age, a visitor to the u.s. goes to a city clinic with reports of diarrhea, weight loss of 20 pounds, and fever. these manifestations have been occurring for the past 5 weeks. the nurse would identify this client to be in which clinical stage? to determine that an item is not in an unordered array of 100 items, how many values must linear search examine on average? garcia company has two operating departments (phone and earbuds) and one service department (office). its departmental income statements follow. indirect expenses and service department expenses consist of rent, utilities, and office department expenses. How does the Mendez v. Westminster case reflect what we have been learning about the trial and appeal process in class? 5 paragraphs on any musical pls A rectangle has an area of 104 square centimeters and a width of 8 centimeters. What is the perimeter? 13 centimeters 26 centimeters 34 centimeters 42 centimeters Hi! Please help asap!!!!!!!!!!!!!! in today's legal environment, managers who are convicted for the misuse of information systems are unlikely to be given a prison sentence. group of answer choices true false which document do property managers and the owners they represent sign to formalize the relationship? on its opening day, a car dealership had an inventory of 29 cars. during the first 6 months, 18 additional cars were purchased by the dealership each week, and the sales team sold an average of 15 cars per week. during the first six months, which of the following equations best models the car inventory, c, at the dealership t weeks after opening day? In a study conducted by a University of Illinois researcher, the football team at Unity High School in Tolono, IL was equipped for an entire season with helmets containing accelerometers. Information about every impact in practice and in games was sent to a computer present on the sidelines. The study found that the average force on a top of the head impact was 1770 N. If the initial velocity of the head was 2.09 m/s and the collision brings the head to a stop, and assuming the head has a mass of 4.12 kg, determine the duration of the impact. (Note: we are treating the head as a free body which is a bit of an approximation). controlling your emotions when a coworker annoys you is an example of emotional . a client with history of alcohol abuse is brought to the emergency department after a weekend of heavy drinking, experiencing right upper quadrant pain, anorexia, nausea, jaundice and ascites. the nurse identifies these as manifestations of what disorder? RSTP serves as an improved protocol in comparison to the older STP. Which of the following answers lists a feature of RSTP that does not exist in STP?The criteria used by a nonroot switch to choose its own root portThe criteria used by switches to determine the designated port on a segmentThe criteria used by switches to determine a port to act in the backup port roleThe criteria used by switches to elect a root switch what is one similarity or difference between the ways that leaders achieved german unification and italian unification how many moles are in 50.00g of ag? to what extent is it accurate to say that the defining factor in the evolution of political communication has been the technologies used to convey messages? The zero of this function is 3 . What do you think "zero of a function" means?