Answer:
force on brake shoes is 10 N
Explanation:
for the master cylinder;
force applied = 140 N
diameter = 14d
for brake cylinder;
force applied on the brake shoe by the brake cylinder f = ?
diameter = d
The pressure will be transmitted undiminished from the master cylinder to the brake cylinder according to pascals pressure law.
pressure = force/area
but cross sectional area is proportional to diameter of the cylinder
therefore
[tex]\frac{140}{14d } = \frac{f}{d }[/tex]
the diameters will cancel out, and we're left with
force on brake shoes = 10 N
Un proyectil es lanzado horizontalmente desde una altura de 12 metro con una velocidad de 80 m/sg. a.Calcular el tiempo de vuelo b. Su alcance horizontal y velocidad de impacto contra el suelo.
Answer:
t= 1,56 s , x= 124,8 m , v = (80 i^ - 15,288 j ) m/s
Explanation:
Este es un ejercicio de lanzamiento proyectiles, comencemos por encontrar el tiempo que tarda en llegar al piso
y = y₀ + [tex]v_{oy}[/tex] t – ½ g t²
en este caso la altura inicial es y₀= 12 m y llega a y=0 , como es lanzado horizontalmente la velocidad vertical es cero (v_{oy}=0)
0 = y₀ – ½ g t²
t= √ (2 y₀/g)
calculemos
t= √ ( 2 12 / 9,8)
t= 1,56 s
El alcance del proyectil es la distancia horizontal recorrida
x = v₀ₓ t
x = 80 1,56
x= 124,8 m
La velocidad de impacto cuando toca el suelo
vx = v₀ₓ = 80 ms
[tex]v_{y}[/tex] = v_{oy} – gt
v_{y} = - 9,8 1,56
v_{y} = - 15,288 m/s
la velocidad es
v = (80 i^ - 15,288 j ) m/s
Traducttion
This is a projectile launching exercise, let's start by finding the time it takes to reach the ground
y = y₀ + v_{oy} t - ½ g t²
in this case the initial height is i = 12 m and it reaches y = 0, as it is thrown horizontally the vertical speed is zero ([tex]v_{oy}[/tex] = 0)
0 =y₀I - ½ g t²
t = √ (2y₀ / g)
let's calculate
t = √ (2 12 / 9.8)
t = 1.56 s
Projectile range is the horizontal distance traveled
x = v₀ₓ t
x = 80 1.56
x = 124.8 m
Impact speed when it hits the ground
vₓ = v₀ₓ = 80 ms
v_{y} = v_{oy} - gt
v_{y} = - 9.8 1.56
v_{y} = - 15,288 m / s
the speed is
v = (80 i ^ - 15,288 j) m / s
a boy runs from his house to school at speed 5m/s on a straight road and returns with speed of 10m/s.The distance between the house and school is 100m. Find his average velocity.... with explaination please
Explanation:
time spent to run from house to school=100/5=20s
time spent to return from school=100/10=10s
average velocity=200m/(10+20)
=6.66m/s2. Find the time taken by the bus to reach the stop. need only group B, 2 answer
Answer:
t = 2 seconds
Explanation:
In 2nd question, the question is given the attached figure.
Initial speed of the bus, u = 0
Acceleration of the bus, a = 8 m/s²
Final speed, v = 16 m/s
We need to find the time taken by the car to reach the stop. Acceleration of an object is given by :
[tex]a=\dfrac{v-u}{t}[/tex]
t is time taken
[tex]t=\dfrac{v-u}{a}\\\\t=\dfrac{16-0}{8}\\\\t=2\ s[/tex]
The bus will take 2 seconds to reach the stop.
A body oscillates with 25hz what is its time period
Answer:
4 seconds
Explanation:
The frequency of a body is the number of oscillations in one second. It is the number of cycles per unit time. The S.I unit of frequency is the Hertz (Hz).
The period of a body is the time taken to complete one oscillation. The period is inversely proportional to the frequency of the body. It is the reciprocal of frequency and the S.I unit is second (s).
A body oscillates with 25hz. Therefore the frequency (f) = 25 Hz.
The period (T) is given as:
[tex]Period (T)=\frac{1}{frequency(f)} \\T=\frac{1}{f} =\frac{1}{0.25}=4\\T=4\ seconds[/tex]
A 17-tooth spur pinion has a diametral pitch of 8 teeth/in, runs at 1016 rev/min, and drives a gear at a speed of 508 rev/min. Find the number of teeth on the gear and the theoretical center-to-center distance.
A broom with a long handle balances at its centre of gravity as shown in the figure. If you cut the broom into two parts through the centre of gravity and then weigh each part, which part will weigh more? a) The part with the broom will weigh more. b) The part without the broom will weigh more c) Both the parts will weigh the same d) It would depend on the weight of the broom
Answer:
c) Both the parts will weigh the same
Explanation:
center of gravity is based on weight so if you cut down the center of gravity you would have 2 equal parts
(might be D if it is cutting against the center of gravity)
Find the electric field a distance z above a circular ring carrying a constant line charge. For extra credit you may derive the electric field a distance z above a disk carrying a constant surface charge density. 3 Find the force between an electron and a proton in a typical hvdrogen atom.
Answer:
F = 8.23 × 10⁻⁸N
Explanation:
F= kq²/r²
k= 9×10⁹Nm²/C²
q= 1.6×10⁻¹⁹C
r= 5.29×10⁻¹¹m
F= 9×10⁹× (1.6×10⁻¹⁹)²/ (5.29×10⁻¹¹)²
F = 8.23 × 10⁻⁸N
I NEED HELP PLEASE, THANKS! :)
The electric field around a positive charge is shown in the diagram. Describe the nature of these lines.
Answer:
They move outwards.
They don't intersect each other at any point.
They show the electric field.
Explanation:
Answer:
Please read the answer below
Explanation:
the nature of these lines refers to the fact that positive charges generate field lines that are directed out of the positive charges, and in turn are directed towards some negative charge present somewhere in the universe.
By consensus, the electric field lines leave the positive charges and enter the negative charges. That is the reason why in a scheme like the shown in the image, is considered implicitly the existence of a negative charge, in some place of the universe.
The kicker now kicks the ball with the same speed as in the number of 4,but at 60.0°from the horizontal or 30.0° from the vertical. a.What is the time the ball is in the air? b.What is the distance the balls travel before it hits the ground? c.What is the maximum height?
Answer:
Explanation:
1) The time of flight equation for projectile motion can be used here to find total time in air.
t = 2vsin∅ / g
where v is speed, Ф is launch angle
t = 2×4×sin 60 / 9.8
t = 0.71 seconds
2) Distance where it hit the ground is called as range and has the following standard equation
D = v² sin2Ф/g
D = 4²sin 2×60 / 9.8
D = 1.41m
3) Maximum elevation is maximum time reached
h = v² sin²Ф / 2g
h = 4²sin² 60 / 2*9.8
h = 0.61 m
An airplane starts at rest and accelerates down the runway for 25 s. At the end of the runway, its final velocity is 75 m/s east. What is its acceleration?
Answer
3m/s²
Explanation
u=o
t=25s
v=75m/s
from Newton's first law of motion,
v=u+at
75=0+a(25)
75=25a
a= 75/25
a=3m/s²
The acceleration of the airplane is 3m/s².
What is acceleration?Acceleration is rate of change of velocity with time. Due to having both direction and magnitude, it is a vector quantity. Si unit of acceleration is meter/second² (m/s²).
Given parameters:
Initial velocity of the airplane: u=o.
Time taken: t=25s.
Final velocity of the airplane: v=75m/s.
We have to find acceleration of the plane: a = ?
We know that for accelerating motion of the air plane; final velocity can be expressed as:
v=u+at
⇒ 75=0+a(25)
⇒ 75=25a
⇒ a= 75/25
⇒ a= 3m/s².
hence, acceleration of the airplane is 3m/s².
Learn more about acceleration here:
brainly.com/question/12550364
#SPJ2
A ball moving at a velocity of 10 meters/second has a momentum of 8.0 kilogram meters/second. What is its mass?
Answer:
0.8 kilogram
Explanation:
Mass:This can be defined as the quantity of matter a body contained. The S.I unit of mass if kg.
From the question,
M = mv................. Equation 1
Where M = momentum, m = mass. V = velocity
make m the subject of the equation
m = M/v.............. Equation 2
Given: M = 8.0 kilogram meters/second, v = 10 meters/second
Substitute these values into equation 2
m = 8.0/10
m = 0.8 kilogram
This equation is missing which motion variable?
Answer:
Option A. a
Explanation:
Motion variables include:
1. Final velocity (vf).
2. Initial velocity (vi).
3. Time (t).
4. Acceleration (a)
5. Distance (x)
Considering the equation given in the question:
Δx = ½(vf + vi) t
We can see that the acceleration (a) is missing in the equation.
A 1500kg car accelerates from 50km/h to 75km/h. How much work was done?
Answer:
Work done, W = 181238.4 J
Explanation:
We have,
Mass of a car, m = 1500 kg
Initial speed, u = 50 km/h = 13.88 m/s
Final speed, v = 75 km/h = 20.84 m/s
Let W is the work done. It is equal to the change in kinetic energy of the car. So,
[tex]W=\dfrac{1}{2}m(v^2-u^2)\\\\W=\dfrac{1}{2}\times 1500\times ((20.84)^2-(13.88)^2)\\\\W=181238.4\ J[/tex]
So, 181238.4 J of work was done by the car.
hellllp me please anyone help Light travels from a region of air into a region of air, making an angle of incidence of 60 degrees. Which of the following best describes the path of the light as it moves into the air? A) The light will bend toward the normal B) The light will bend away from the normal C)The light will continue without bending D)The light will move in some manner not determined by the information here.
Answer:
(B)
Explanation:
Because what ever angle the surface is, the light will reflect of of it perpendicular.
Select the correct the answer.
What do the circled arrows in the image indicate?
A. CO2 absorbed by the atmosphere
B. CO2 released to the atmosphere
C. oxygen absorbed by the atmosphere
D. oxygen released by the atmosphere
Answer:
it shows that co2 is absorbed by the atmosphere.
when the animals respire they produce co2 which is release in atmosphere and in presence of sunlight and chlorophyll the plants manufacturs the food and releases the oxygen in the atmosphere .
hope it helps..
Answer:
Its A
Explanation:
A vehicle traveling on wet or slick roads can begin to _________ as water forms a barrier between the road and the tires and traction is lost as the wheels start to ride on top of the water and not the road surface. a) skid b) hydroplane c) lose traction d) splash water on to the engine
Answer: B.) HYDROPLANE
Explanation: The term hydroplane can be used to refer to a condition which usually occur during a downpour or on surfaces covered by water. It occurs when water forms a barrier or comes in between the frictional grip which occurs between the road surface and the car tyres. The contact between the car tyres and the road surface is supposed to give adequate frictional support which prevents the car from skidding or skidding uncontrollably on the road surface. However, when water comes invetween the surface, traction is lost and skidding results due to very low Coefficient of friction between the road and Tyre which was supposed to provide a firm grip between the tyres and the road surface.
When a vehicle is traveling on wet or slick roads, hydroplaning can occur. The correct answer is b) hydroplane.
When a vehicle is traveling on wet or slick roads, hydroplaning can occur. Hydroplaning happens when a layer of water builds up between the tires of the vehicle and the road surface, leading to a loss of traction.
This loss of traction can cause the vehicle to skid or slide, making it difficult to control. The tires ride on top of the water rather than maintaining contact with the road, resulting in reduced traction and control of the vehicle.
Therefore, When a vehicle is traveling on wet or slick roads, hydroplaning can occur. The correct answer is b) hydroplane.
To know more about hydroplaning:
https://brainly.com/question/33723980
#SPJ6
if the input force on a wheel and axle is 2 N and the output force is 20N what is its mechanical advantage
Mechanical Advantage is always (Output Force) / (Input Force) .
MA = (20 N) / (2 N)
MA = 10
With an initial velocity of 9.8 m / sg, an object is thrown upwards from the roof of a 100 m high building. Determine maximum height from the ground, time it takes to reach the ground, and the speed with which it reaches the ground.
Answer:
104.9 m
5.63 s
45.3 m/s
Explanation:
Given:
y₀ = 100 m
v₀ = 9.8 m/s
a = -9.8 m/s²
Find: y when v = 0 m/s
v² = v₀² + 2a (y − y₀)
(0 m/s)² = (9.8 m/s)² + 2 (-9.8 m/s²) (y − 100 m)
y = 104.9 m
Find: t when y = 0 m
y = y₀ + v₀ t + ½ at²
0 m = 100 m + (9.8 m/s) t + ½ (-9.8 m/s²) t²
0 = 100 + 9.8t − 4.9t²
t = [ -9.8 ± √(9.8² − 4(-4.9)(100)) ] / 2(-4.9)
t = (-9.8 ± 45.3) / -9.8
t = 5.63 s
Find: v when y = 0 m
v² = v₀² + 2a (y − y₀)
v² = (9.8 m/s)² + 2 (-9.8 m/s²) (0 m − 100 m)
v = -45.3 m/s
|v| = 45.3 m/s
What is electrical power in terms of current and potential difference? Explain.
Answer:
Ohm's Law:
[tex]V = IR[/tex]
Where V is voltage, I is current and R is resistance
While,
[tex]P = IV[/tex]
Where P is power, I is current and V is voltage (or potential difference)
So, Electrical power is the product of current and potential difference.
Modifiable strength improvement factors include all of the following except...??
Answer:
Muscle size and training specifiicty
Explanation:
It depends on all other factors such as anatomy and psychology, muscle fiber recruitment, motor pattern development and muscle memory but to increase modifiable strength, size plays no big role.
Using the letters for the seven colours and starting with R (Red), what is the correct order for the colours in a rainbow? Your answer should be in the form RXXXXXX Which of these seven colours has the shortest wavelength?
Answer:
Red
Orange
Yellow
Green
Blue
Indigo
Violet
shortest wavelength: violet (380 nanometers)
¯\(°_o)/¯
Answer:
Red Orange Yellow Green Blue Indigo Violet
violet has the shortest wavelength
happy to help :)
Does the earths magnetic field change with time?
Answer:
As per the fossil fuel records, magnetic field reversal does not impact living beings. It will take almost a century for the poles to complete the shift. Meanwhile, the earth is left with almost zero magnetic field.
The cartoon of the roadrunner and the coyote usually has rockets going at around 8 kilometers per minute. How much is this in miles per hour? (1m = .00062 miles)If we have a terrain with a square house in the middle, the walls of the square house are 50.0 yards long and has 10 yards high ceilings. What is the volume of the interior of the house in cubic meters and cubic centimeters? (1 yard = 3 feet, 1 meter = 3.28 foot)The acceleration of an object is given by 314,000 Hectometers per hour squared. Convert the units to Meter per second square and miles per second square.
Answer:
1 feet
Explanation:
1 feet = 1 feet so its one feet
At one point in the rescue operation, breakdown vehicle A is exerting a force of 4000 N and breakdown vehicle B is exerting a force of 2000 N.(i) Using a scale of 1 cm = 500 N, make a scale drawing to show the resultant force on the truck. (ii) Use your diagram to find the magnitude and direction of the resultant force on the truck.
Answer:
1.) Magnitude = 5596 N
2.) Direction = 60 degrees
Explanation: You are given that the breakdown vehicle A is exerting a force of 4000 N at angle 45 degree to the vertical and breakdown vehicle B is exerting a force of 2000 N
Let us resolve the two forces into X and Y component
Sum of the forces in the X - component will be 4000 × cos 45 = 2828.43 N
Sum of the forces in the Y - component will be 2000 + ( 4000 × sin 45 )
= 2000 + 2828.43
= 4828.43 N
The resultant force R will be
R = sqrt ( X^2 + Y^2 )
Substitutes the forces at X component and Y component into the formula
R = sqrt ( 2828.43^2 + 4828.43^2 )
R = sqrt ( 31313752.53 )
R = 5595.87 N
The direction will be
Tan Ø = Y/X
Substitute Y and X into the formula
Tan Ø = 4828.43 / 2828.43
Tan Ø = 1.707106
Ø = tan^-1( 1.707106 )
Ø = 59.64 degree
Therefore, approximately, the magnitude and direction of the resultant force on the truck are 5596 N and 60 degree respectively.
the weight of a body will be zero during free fall. Why?
Answer:
The apparent weight of a freely falling body is zero. When a body falls freely, it is falling with an acceleration =g. Thus the entire gravitational force acting on it is utilized in accelerating it and hence its weight is not felt.
HELP NEEDE ASAP!!!!!!!! How do you understand by the longitudinal wave? Describe the longitudinal nature of sound waves
Answer:
Sound as a Longitudinal Wave
For a sound wave traveling through air, the vibrations of the particles are best described as longitudinal. Longitudinal waves are waves in which the motion of the individual particles of the medium is in a direction that is parallel to the direction of energy transport.
Answer:
Hey!
Here is your answer!
Explanation:
LONGITUDINAL WAVES:
These are waves where the transferral of energy is PARALLEL to the direction it travels in...For Example...Sound Waves are Longitudinal as they move in a series of COMPRESSIONS and RAREFACTIONS (typical of all Longitudinal Waves)...
The compressions are known in diagrams to be an area of a dense collection of PARTICLES where the energy (or sound in this case) is being transferred in the same direction as the movement...
The rarefactions are shown as almost empty area of particles where the medium (the matter of which the wave travels in) is moving...
Hope this helps!
*here's a diagram*
In which direction of the wave motion do longitudinal waves transfer energy?
A-perpendicular
B- parallel
C- close
D-equal
Answer:
B, Parallel.
Explanation:
Mark as brainliest pls!
The wave motion does longitudinal waves transfer energy in the direction Parallel to the wave motion. Hence, option B is correct.
What is a Wave?Waves are disturbances that move regularly and orderly from one location to another. Although sound, lighting, and the movement of elementary particles all have wave-like characteristics, surface waves that move on water are the most well-known.
The disturbance periodically oscillates with a set frequency and wavelength in the simplest waves (see periodic motion). In contrast to electromagnetic waves, which do not require a medium to travel and may move through a vacuum, mechanical waves, like sound, need a medium to go through. A medium's characteristics determine how a wave will travel across it. Seismic wave is also seen.
Therefore, option B is correct.
To know more about Wave:
https://brainly.com/question/3639648
#SPJ6
Explain the concept of "charge" and how it relates to electricity?
Answer:
An Electric "charge" is a property of matter that causes a force to repel or attract when placed into a magnetic field. These charges can be replicated into positive and negative electrons when made from a chemical reaction.
Answer:
an electri
Explanation:
pls help, me, i nees to submit now
Answer:
12m
Explanation:
To obtain the answer to the question given, we must observe the characteristics of image formed by a plane mirror.
The image formed by a plane mirror have the following characteristics:
1. Laterally inverted.
2. Same distance as the object from the mirror.
3. Same height as the object.
4. Virtual.
With the above information, we can calculate the distance between the boy and his image as follow:
Initially:
Object distance (u) = 4m
Image distance (v) = 4m
The boy moved 2m away, therefore:
Object distance (u) = 2 + 4 = 6m
Image distanc(v) = 2 + 4 = 6m
The distance between the boy and his image will be the sum of his distance (u) and image distance (v) i.e (u + v)
The distance between the boy and his image = 6 + 6 = 12m
Therefore, the distance between the boy and his image is 12m.
what is called gratational force
Answer:
Gravitational force can be seen as the pull that the earth has on an piece of matter. Everything on earth has a force acting on it which is gravity. It tries to pull two object closer to each other but never apart. The numerical value for gravitational force is 9.8 m/s^2 for free falling objects