The Nusselt number at the exit obtained during the experiment is given by;
NuD = 0.023ReD⁴/₃Prⁿ, where ReD = ρVD/μ, V = ṁ/ρA and ṁ is the mass flow rate.
The given mass flow rate is 0.010 kg/s. The diameter of the tube is 0.0103 m and the cross-sectional area of the tube is given by A = (π/4) D².
The density of water is given by ρ = 1000 kg/m³.
Hence, the velocity of the fluid can be calculated as follows;
V = ṁ/ρA = (0.010 kg/s)/(1000 kg/m³ × (π/4) × (0.0103 m)²) = 0.838 m/s
The Reynolds number can now be calculated as; ReD = ρVD/μ = (1000 kg/m³ × 0.838 m/s × 0.0103 m)/(1.000×10⁻³ kg/m·s) = 8628
The flow is fully developed when ReD > 4000.
Hence, the flow is fully developed at the exit because ReD > 4000.
The Nusselt number can now be calculated using; NuD = 0.023ReD⁴/₃PrⁿNuD at the exit of the tube is given by;
NuD = 0.023(8628)⁴/₃(7)ⁿ
The Nusselt number, however, depends on the exponent n. This exponent n depends on the geometry of the surface. However, for the fully developed laminar flow in a smooth tube, n = 0.4.
Hence, the Nusselt number at the exit is given by;NuD = 0.023(8628)⁴/₃(7)⁰․⁴ = 86.7
To know more about mass flow rate refer to:
https://brainly.com/question/13148276
#SPJ11
1. Apply the correct demand factors to the loads and calculate the minimum watt capacity required for a; a. 6450 sq foot store b. 2250 sq foot residence C. 124000 sq foot school d. Disposal.75000 sq foot hospital 2. Find the maximum demand for an installation of. a. 16.9 kW range b. 44 of 10 kW range 3. Determine the demand factor for a. 3 clothes dryer e. 5 clothes dryer c. 16 clothes dryer b. 7 clothes dryer 4. One floor of apartment building holds 14 apartments that are each 20 ft x 30 ft, and have a 9 kW range, 6 kW of electric heat, 2 small appliances circuits, and a 0.5 kW disposal. For each apartment calculate the following; a. The general lighting load in watts b. The minimum number of 115 V, 15 A lighting circuits required C. The total small appliance and lighting load after applying of demand factors d. The net watts e. The current required f. And choose the RH aluminum conductor AWG #.
The answer involves performing calculations for various scenarios, including watt capacity, maximum demand, demand factors, and circuit requirements for different types of buildings and appliances.
What are the key considerations when designing a scalable and secure cloud infrastructure?The provided set of questions involves calculations related to electrical demand factors, watt capacity requirements, maximum demand, and circuit requirements for various scenarios such as a store, residence, school, hospital, and apartment building.
Each question requires specific calculations such as applying demand factors, determining maximum demand, and calculating loads and circuit requirements.
The answers to these questions would involve performing the required calculations for each scenario and providing the appropriate values, such as watt capacity, number of circuits, total load, net watts, current, and selecting the appropriate conductor size.
Learn more about capacity, maximum
brainly.com/question/30088508
#SPJ11
3.7 Please describe the advantages and disadvantages of up-wind
and down-wind horizontal wind turbines. To clarify your discussion,
you may wish to construct system diagrams.
Up-wind turbines offer higher efficiency and stability but come with increased complexity and costs, while down-wind turbines may have simpler design and lower costs but present challenges in stability and control.
What are the advantages and disadvantages of up-wind and down-wind horizontal wind turbines?Up-wind and down-wind horizontal wind turbines are two different configurations used in wind turbine designs.
Advantages of up-wind horizontal wind turbines:
Higher efficiency: Up-wind turbines are positioned in front of the wind, allowing them to capture the undisturbed wind flow and achieve higher energy conversion efficiency.Better stability: The tower and support structure can be designed to provide stability by blocking turbulence caused by the rotor, resulting in smoother operation. Lower noise levels: The up-wind configuration reduces the noise generated by the interaction between the rotor and the tower.Disadvantages of up-wind horizontal wind turbines:
Increased complexity: The turbine must incorporate a yaw mechanism to face the wind direction, which adds complexity and maintenance requirements. Higher costs: The additional components and mechanisms make up-wind turbines more expensive to manufacture and maintain.3. Limitations in wind speed range: Up-wind turbines may have a limited operating range, as they are prone to damage in high winds due to the increased exposure to turbulent wind conditions.In contrast, down-wind horizontal wind turbines have their own set of advantages and disadvantages, which may include simpler design, lower costs, potential aerodynamic benefits, and challenges related to stability and turbine control.
Learn more about wind turbines
brainly.com/question/12304821
#SPJ11
4. Write down the general expressions of frequency modulated signal a modulated signal. And show the methods to generate FM signals.
1) The general expression of a frequency-modulated (FM) signal is:
s(t) = Ac * cos[2πfct + φ(t)]
2) The methods to generate FM signals are:
Direct FM
Indirect FM
Phase-Locked Loop (PLL)
Software-Based FM
How to express Frequency modulated signals?1) The general expression of a frequency-modulated (FM) signal is:
s(t) = Ac * cos[2πfct + φ(t)]
Where:
s(t) is the FM signal as a function of time.
Ac is the amplitude of the carrier signal.
fc is the frequency of the carrier signal.
φ(t) represents the phase deviation or modulation as a function of time.
2) The methods to generate FM signals are:
Direct FM: In this method, the modulating signal directly changes the frequency of the carrier signal. This is accomplished by connecting the modulating signal to a Voltage Controlled Oscillator (VCO). The voltage level determines the frequency deviation of the carrier signal.
Indirect FM: In this method, the modulating signal first changes the amplitude of the carrier signal and then uses a frequency modulator to convert the amplitude modulation to frequency modulation. The modulating signal is applied to a voltage controlled amplifier (VCA) that modulates the amplitude of the carrier signal. The resulting signal is fed to a frequency multiplier or modulator to convert amplitude modulation to frequency modulation.
Phase-Locked Loop (PLL): A PLL allows you to generate FM signals using phase detectors, loop filters, and voltage controlled oscillators (VCOs). A modulating signal is applied to the control input of the VCO, and the phase detector compares the phase of the VCO output with a reference signal. A loop filter adjusts the VCO control voltage based on the phase difference, resulting in frequency modulation.
Software-Based FM: FM signals can also be generated using software-based methods. Using digital signal processing techniques, FM signals can be generated by manipulating the carrier frequency and phase based on the modulating signal. It is commonly used in software defined radio (SDR) systems.
Read more about Frequency Modulated Signals at: https://brainly.com/question/33223009
#SPJ4
consider true or an F for (10 pomis) Calculating setup-time cost does not require a value for the burden rate, Captured quality refers to the defects found before the product is shipped to the customer. The number of inventory turns is the average number of days that a part spends in production Flexibility never measures the ability to produce new product designs in a short time. Computers use an Alphanumeric System. While our words vary in length, computer words are of fixed length. In the spline technique, the control points are located on the curve itself. Bezier curves allow for local control. Wireframe models are considered true surface models. A variant CAPP system does not require a database containing a standard process plan for each family of parts. When similar parts are being produced on the same machines, machine setup times are reduced. The average-linkage clustering algorithm (ALCA) is well suited to prevent a potential chaining effect. PLCs are not microprocessor-based devices. PLC technology was developed exclusively for manufacturing. Ladder diagrams have been used to document connection circuits. In a ladder diagram each rung has at least two outputs. TON timers always need a Reset instruction. If the time base of a timer is one the preset value represents seconds Allen-Bradley timers have three bits (EN, DN, and TT). In an off-delay timer the enabled bit and the done bit become true at the same time.
Calculating setup-time cost does not require a value for the burden rate. Captured quality refers to defects found after the product is shipped. The number of inventory turns measures the average number of times inventory is sold or used in a given period.
Flexibility can measure the ability to produce new product designs quickly. Computers use a binary system, not an alphanumeric system. Words in computer systems are not of fixed length. Control points in the spline technique are not located on the curve itself. Bezier curves do allow for local control. Wireframe models are not considered true surface models. A variant CAPP system requires a database with standard process plans. Similar parts being produced on the same machines may reduce setup times. The average-linkage clustering algorithm is not specifically designed to prevent a chaining effect. PLCs are microprocessor-based devices. PLC technology was not developed exclusively for manufacturing. Ladder diagrams document connection circuits. Each rung in a ladder diagram can have multiple outputs. TON timers do not always need a reset instruction. The preset value of a timer represents the time base, not necessarily seconds. Allen-Bradley timers have more than three bits (EN, DN, and TT). In an off-delay timer, the enabled bit and the done bit do not become true at the same time.
Learn more about average-linkage clustering here:
https://brainly.com/question/31194854
#SPJ11
The stream function of a 2D non-viscous fluid flow is given by . Determine if this fluid flow is incompressible or not, calculate the vorticity in this flow field and determine the pressure gradient in horizontal x direction at coordinate (1,4).
The fluid flow described by the given stream function is incompressible. The vorticity of this flow field is zero. The pressure gradient in the horizontal x direction at coordinate (1,4) cannot be determined without additional information.
In fluid dynamics, an incompressible flow refers to a flow where the density of the fluid remains constant. The incompressibility condition is mathematically expressed as ∇ · v = 0, where ∇ is the del operator and v represents the velocity vector of the fluid flow. In the given problem, the stream function is provided, but the velocity vector is not explicitly given. However, the stream function is related to the velocity components through the equations ∂ψ/∂y = u and ∂ψ/∂x = -v, where u and v are the x and y components of the velocity vector. Taking the derivatives of these equations, we find ∂²ψ/∂x² + ∂²ψ/∂y² = 0, which satisfies the incompressibility condition (∇ · v = 0). Hence, the fluid flow described by the given stream function is incompressible.
Vorticity is a measure of the local rotation of fluid particles in a flow. It is defined as the curl of the velocity vector, given by ∇ × v. Since the velocity vector is related to the stream function as mentioned earlier, we can calculate the vorticity as ∇ × (∂ψ/∂y, -∂ψ/∂x). Taking the curl, we obtain ∇ × (∂ψ/∂y, -∂ψ/∂x) = ∂²ψ/∂x² + ∂²ψ/∂y². As this expression evaluates to zero in the given problem, the vorticity in this flow field is zero.
To determine the pressure gradient in the horizontal x direction at coordinate (1,4), we need additional information. The stream function alone does not provide a direct relationship with the pressure gradient. Other governing equations, such as the Bernoulli equation or the Navier-Stokes equations, would be required to establish the pressure distribution in the flow field and calculate the pressure gradient.
Learn more about fluid flow
brainly.com/question/28727482
#SPJ11
QUESTION 1 Which of the followings is true? For wideband FM, O A. complex envelope can always be defined. O B. the complex envelope would always need to be formulated. O C. its bandwidth is typically difficult to compute for arbitrary messages. O D. the modulation index beta can always be defined.
For wideband FM, the complex envelope can always be defined. Wideband frequency modulation (FM).
The complex envelope in FM refers to the complex representation of the modulated signal. In FM, the complex envelope can always be defined because the modulation process involves the direct modulation of the carrier frequency. The modulated signal can be represented as a complex exponential with a varying frequency, which allows for the formulation of the complex envelope. The complex envelope representation is useful in analyzing the spectral characteristics and demodulation of wideband FM signals. It provides a convenient way to separate the amplitude and phase components of the modulated signal, facilitating the analysis of signal propagation, bandwidth requirements, and demodulation techniques. Therefore, for wideband FM, the complex envelope can always be defined, enabling the analysis and processing of FM signals using complex representation techniques.
learn more about FM here :
https://brainly.com/question/1392064
#SPJ11
Score =. (Each question Score 12points, Total Score 12 points ) An information source consists of A, B, C, D and E, each symbol appear independently, and its occurrence probability is 1/4, 1/8, 1/8, 3/16 and 5/16 respectively. If 1200 symbols are transmitted per second, try to find: (1) The average information content of the information source; (2) The average information content within 1.5 hour. (3) The possible maximum information content within 1 hour.
Sure, I can help you with that.
1. The average information content of the information source
The average information content of an information source is calculated by multiplying the probability of each symbol by its self-information. The self-information of a symbol is the amount of information that is conveyed by the symbol. It is calculated using the following equation:
```
H(x) = -log(p(x))
```
where:
* H(x) is the self-information of symbol x
* p(x) is the probability of symbol x
Substituting the given values, we get the following self-information values:
* A: -log(1/4) = 2 bits
* B: -log(1/8) = 3 bits
* C: -log(1/8) = 3 bits
* D: -log(3/16) = 2.5 bits
* E: -log(5/16) = 2.3 bits
The average information content of the information source is then calculated as follows:
```
H = p(A)H(A) + p(B)H(B) + p(C)H(C) + p(D)H(D) + p(E)H(E)
```
```
= (1/4)2 + (1/8)3 + (1/8)3 + (3/16)2.5 + (5/16)2.3
```
```
= 1.8 bits
```
Therefore, the average information content of the information source is 1.8 bits.
2. The average information content within 1.5 hour
The average information content within 1.5 hour is calculated by multiplying the average information content by the number of symbols transmitted per second and the number of seconds in 1.5 hour. The number of seconds in 1.5 hour is 5400.
```
I = H * 1200 * 5400
```
```
= 1.8 bits * 1200 * 5400
```
```
= 11664000 bits
```
Therefore, the average information content within 1.5 hour is 11664000 bits.
3. The possible maximum information content within 1 hour
The possible maximum information content within 1 hour is calculated by multiplying the maximum number of symbols that can be transmitted per second by the number of seconds in 1 hour. The maximum number of symbols that can be transmitted per second is 1200.
```
I = 1200 * 3600
```
```
= 4320000 bits
```
Therefore, the possible maximum information content within 1 hour is 4320000 bits.
Learn more about information theory here:
https://brainly.com/question/31566776
#SPJ11
D2.5 For second-order systems with the following transfer functions, determine the undamped natural frequency, the damping ratio, and the oscillation frequency. T(s) = 100/s2 +s $2+3s +49
The undamped natural frequency, damping ratio, and oscillation frequency of a second-order system with the transfer function T(s) = 100/(s^2 + s^2 + 3s + 49), we can express the transfer function in the standard second-order form:
T(s) = ωn^2 / (s^2 + 2ζωn s + ωn^2)
Comparing the standard form with the given transfer function, we can find the values of ωn (undamped natural frequency) and ζ (damping ratio).
For the given transfer function, we have:
ωn^2 = 100
2ζωn = 3
Let's solve these equations to find the values of ωn and ζ:
From the equation 2ζωn = 3, we can solve for ζ:
ζ = 3 / (2ωn)
Substituting the value of ωn from the equation ωn^2 = 100, we get:
ζ = 3 / (2 * √(100))
ζ = 3 / 20
So, the damping ratio ζ is 0.15.
Now, let's find the undamped natural frequency ωn:
ωn^2 = 100
ωn = √100
ωn = 10
Therefore, the undamped natural frequency ωn is 10.
To find the oscillation frequency, we can use the relationship:
Oscillation Frequency (ωd) = ωn * √(1 - ζ^2)
Substituting the values, we get:
ωd = 10 * √(1 - (0.15)^2)
ωd = 10 * √(1 - 0.0225)
ωd = 10 * √(0.9775)
ωd ≈ 9.887
So, the oscillation frequency ωd is approximately 9.887.
In summary, for the given transfer function, the undamped natural frequency (ωn) is 10, the damping ratio (ζ) is 0.15, and the oscillation frequency (ωd) is approximately 9.887.
Learn more about second-order here:
brainly.com/question/30853813
#SPJ11
The lna has g = 15 db and nf = 1.5 db. the mixer has a conversion gain of g = 10 db and nf = 10 db. the if amplifier has g = 70 db and nf = 20 db.
The overall gain and noise figure of the system can be calculated by cascading the gains and noise figures of the individual components. The main answer is as follows:
The overall gain of the system is 95 dB and the overall noise figure is 30 dB.
To calculate the overall gain, we sum up the individual gains in dB:
Overall gain (G) = G1 + G2 + G3
= 15 dB + 10 dB + 70 dB
= 95 dB
To calculate the overall noise figure, we use the Friis formula, which takes into account the noise figure of each component:
1/NF_total = 1/NF1 + (G1-1)/NF2 + (G1-1)(G2-1)/NF3 + ...
Where NF_total is the overall noise figure in dB, NF1, NF2, NF3 are the noise figures of the individual components in dB, and G1, G2, G3 are the gains of the individual components.
Plugging in the values:
1/NF_total = 1/1.5 + (10-1)/10 + (10-1)(70-1)/20
= 0.6667 + 0.9 + 32.7
= 34.2667
NF_total = 1/0.0342667
= 29.165 dB
Therefore, the overall noise figure of the system is approximately 30 dB.
In summary, the overall gain of the system is 95 dB and the overall noise figure is 30 dB. These values indicate the amplification and noise performance of the system, respectively.
Learn more about gains
brainly.com/question/32279832
#SPJ11.
QUESTION 11 Which of the followings is true? For FM, the phase deviation is given as a function of sin(.) to ensure that O A. the FM spectrum can be computed using Carson's rule. B. deployment of cosine and sine functions is balanced. O C. the wideband FM can be generated using Carson's rule. O D. the message is positive.
For FM, the phase deviation is given as a function of sin(.) to ensure that the FM spectrum can be computed using Carson's rule.
A result of the modulating signal. It is typically expressed as a function of sin(.), where "." represents the modulating signal. One of the key reasons for representing the phase deviation as a function of sin(.) is to ensure that the FM spectrum can be computed accurately using Carson's rule. Carson's rule is a mathematical formula that provides an estimation of the bandwidth of an FM signal. By using sin(.) in the expression for phase deviation, the FM spectrum can be calculated using Carson's rule, which simplifies the analysis and characterization of FM signals. Carson's rule takes into account the modulation index and the highest frequency component of the modulating signal, both of which are related to the phase deviation. Therefore, by specifying the phase deviation as a function of sin(.), the FM spectrum can be effectively determined using Carson's rule, allowing for efficient signal processing and communication system design.
learn more about deviation here :
https://brainly.com/question/31835352
#SPJ11
Consider the 2-D rectangular region 0 ≤ x ≤ a, 0 ≤ y ≤ b that has an initial uniform temperature F(x, y). For t > 0, the region is subjected to the following boundary conditions: The boundary surfaces at y = 0 and y = b are maintained at a prescribed temperature To, the boundary at x 0 dissipates heat by convection into a medium with fluid temperature To and with a heat transfer coefficient h, and the boundary surface at x = = 8 a is exposed to constant incident heat flux qő. Calculate the temperature T(x, y, t).
The temperature T(x, y, t) within the 2-D rectangular region with the given boundary conditions, we need to solve the heat equation, also known as the diffusion equation,
which governs the temperature distribution in a conducting medium. The heat equation is given by:
∂T/∂t = α (∂²T/∂x² + ∂²T/∂y²)
where T is the temperature, t is time, x and y are the spatial coordinates, and α is the thermal diffusivity of the material.
Since the boundary conditions are specified, we can solve the heat equation using appropriate methods such as separation of variables or finite difference methods. However, to provide a general solution here, I will present the solution using the method of separation of variables.
Assuming that T(x, y, t) can be written as a product of three functions: X(x), Y(y), and T(t), we can separate the variables and obtain three ordinary differential equations:
X''(x)/X(x) + Y''(y)/Y(y) = T'(t)/αT(t) = -λ²
where λ² is the separation constant.
Solving the ordinary differential equations for X(x) and Y(y) subject to the given boundary conditions, we find:
X(x) = C1 cos(λx) + C2 sin(λx)
Y(y) = C3 cosh(λy) + C4 sinh(λy)
where C1, C2, C3, and C4 are constants determined by the boundary conditions.
The time function T(t) can be solved as:
T(t) = exp(-αλ²t)
By applying the initial condition F(x, y) at t = 0, we can express F(x, y) in terms of X(x) and Y(y) and determine the appropriate values of the constants.
Learn more about boundary here:
brainly.com/question/30853813
#SPJ11
For all questions, it is desired to achieve the following specifications: 10% overshoot., 1-second settling time for a unit step input. Question 1: Given the following open-loop plant: G(s) = 20/s(s+ 4)(s + 5) design a controller to yield a10% overshoot and a settling time of 1 seconds. Place the third pole 10 times as far from the imaginary axis as the dominant pole pair.
The given plant transfer function is G(s) = 20/s(s+4)(s+5). Design a controller to obtain a 10% overshoot and a settling time of 1 second. Place the third pole 10 times as far from the imaginary axis as the dominant pole pair.A closed-loop system can be used for the implementation of a controller that is supposed to achieve the required specifications.
The design of a controller for the plant is done as follows:-
Step 1: Evaluate the system's transient response to the unit step input. The dominant pole of the plant transfer function is located at -1.25 and has a damping ratio of 0.5. The natural frequency is obtained by dividing the damping ratio by the settling time; omega_n = 4/1 = 4 rad/s. The desired characteristic equation for a second-order system that meets the required specifications is given by s^2 + 2*zeta*omega_n*s + omega_n^2 = 0, where zeta = 0.5. We can use this equation to compute the values of K and a. This is the characteristic equation we get:s^2 + 4s + 25 = 0
Step 2: Let's place the third pole at 10 times the distance from the imaginary axis as the dominant pole pair. The dominant pole pair is 1.25 +/- j2.958. Then the third pole is located at -10 + j29.58. This provides for better damping of the response of the closed-loop system to unit step inputs.
Step 3: Now that the location of the closed-loop poles is known, we can use the desired characteristic equation to compute the values of K and a, as follows:s^3 + 6.25s^2 + 38.75s + 100K = 100, a = 38.75
Substitute the value of s with the desired location of the closed-loop poles to compute K, K = 12.2676.Then the transfer function of the controller is given byC(s) = K(s + 10 - j29.58)(s + 10 + j29.58)/s^2 + 4s + 25The block diagram of the closed-loop control system is shown below:-
Block diagram of closed-loop control system Where C(s) is the controller transfer function, and G(s) is the plant transfer function. The closed-loop transfer function is given by the equation:T(s) = C(s)G(s)/[1 + C(s)G(s)]Substitute C(s) and G(s) into the equation to obtain the transfer function of the closed-loop control system.T(s) = 1846.93(s + 10 - j29.58)(s + 10 + j29.58)/[s^3 + 6.25s^2 + 38.75s + 1846.93(s + 10 - j29.58)(s + 10 + j29.58)].
To learn more about "Closed Loop System" visit: https://brainly.com/question/11995211
#SPJ11
Suppose a factory has following loads connected to the main supply of 415 V, 50 Hz: (a) 40 kVA, 0.75 lagging, (b) 5 kVA, unity pf.; and (c) 40 kVA, 0.75 leading. Find the element needed to correct the power factor to 0.95 lagging and draw phasor diagram for the given problem.
To correct the power factor to 0.95 lagging, we need to add a reactive element to the load that will provide the necessary reactive power to compensate for the lagging or leading power factor of the existing loads.
Given loads:
(a) 40 kVA, 0.75 lagging
(b) 5 kVA, unity power factor
(c) 40 kVA, 0.75 leading
To find the reactive element needed, we can calculate the total apparent power and the total reactive power of the loads.
Total apparent power (S) is the sum of the apparent powers of the individual loads:
[tex]S = S_a + S_b + S_c[/tex]
where [tex]S_a, \:S_b, \:and\: S_c[/tex] are the apparent powers of loads (a), (b), and (c) respectively.
Total reactive power (Q) is the sum of the reactive powers of the individual loads:
[tex]Q = Q_a + Q_b + Q_c[/tex]
where [tex]Q_a[/tex], [tex]Q_b[/tex], and [tex]Q_c[/tex] are the reactive powers of loads (a), (b), and (c) respectively.
To calculate the reactive power Q, we can use the formula:
[tex]\[Q = S \cdot \tan(\cos^{-1}(pf) - \cos^{-1}(desired\_pf))\][/tex]
Using the given values, we can calculate the total apparent power and total reactive power. Then, we can find the reactive element needed to correct the power factor to 0.95 lagging.
The phasor diagram represents the voltages, currents, and power factors of the loads. It helps visualize the relationships between these quantities and the power triangle. The diagram will illustrate the before and after correction scenarios, showing the change in power factor and the addition of the reactive element.
Learn more about the power factor here:
brainly.com/question/11957513
#SPJ11
A long cylindrical tod of diameter D1=0.01 m is costed with this new material and is placed in an evacuated long cylindrical enclosure of diameter D2=0.1 mand emissivity e2 = 4.95. which is cooled extemally and maintained at a kemperature of 200 K at all times. The rod is heated by passing electric current through it. When steady operating conditions are reached, it is observed that the rod is dissipating electric power at a rate of 8 W per unit of its length and its sarface temperature is 500 K. Blased on these measurements, determine the emissivity of the coating on the rod.
The emissivity of the coating on the rod is 0.9301.
The heat lost per unit length from the long cylindrical rod is given by:q = -k (A / L) dT/dx
Where,k is the thermal conductivity of the rodA is the surface areaL is the length of the rod
dT/dx is the temperature gradient
The power dissipated per unit length of the rod is given as 8 W.
So,q = - 8 W / m The surface temperature of the rod is given as 500 K. So,T1 = 500 K
The enclosure is evacuated. Hence, there is no convective heat transfer between the surface of the rod and the enclosure.
Hence, the heat transfer from the rod to the enclosure takes place only by radiation.
So,q = σ (A / L) e1 e2 (T1⁴ - T2⁴)σ is the Stefan-Boltzmann constant
e1 is the emissivity of the rodA is the surface area
L is the length of the rod
T1 is the surface temperature of the rod
T2 is the temperature of the enclosure
By comparing the above two equations, we can write,σ (A / L) e1 e2 (T1⁴ - T2⁴) = - 8 W / m
e1 = -8 / σ (A / L) e2 (T1⁴ - T2⁴)
Since T1 and T2 are in Kelvin, the temperature difference can be taken as:
ΔT = T1 - T2 = 500 - 200 = 300 K.
Substituting the values of the constants, we get,e1 = -8 / (5.67 × 10^-8 × π × (0.01 / 2)² × 4.95 × (300)⁴) = 0.9301
Learn more about thermal conductivity at
https://brainly.com/question/13322944
#SPJ11
Steam at 300 psia and 700 F leaves the boiler and enters the first stage of the turbine, which has an efficiency of 80%. Some of the steam is extracted from the first stage turbine at 30 psia and is rejected into a feedwater heater. The remainder of the steam is expanded to 0.491 psia in the second stage turbine, which has an efficiency of 75%.
a.Compute the net work,
b.Compute the thermal efficiency of the cycle.
a) Compute the work done in each turbine stage and sum them up to obtain the net work.
b) Calculate the thermal efficiency by dividing the net work by the heat input to the cycle.
a) To compute the net work, we need to calculate the work done in each turbine stage. In the first stage, we use the efficiency formula to find the actual work output. Then, we calculate the work extracted in the second stage using the given efficiency. Finally, we add these two values to obtain the net work done by the turbine.
b) The thermal efficiency of the cycle can be determined by dividing the net work done by the heat input to the cycle. The heat input is the enthalpy change of the steam from the initial state in the boiler to the final state in the condenser. Dividing the net work by the heat input gives us the thermal efficiency of the cycle.
Learn more about turbine stage here:
https://brainly.com/question/15076938
#SPJ11
State the affinity laws as applicable to centrifugal pumps.State
the affinity laws as applicable to centrifugal pumps.State the
affinity laws as applicable to centrifugal pumps.
Affinity law 1: This law states that if the speed of the centrifugal pump is increased, the head developed by the pump will also increase in proportion to the square of the speed. Affinity law 2: This law states that if the diameter of the impeller of the centrifugal pump is increased or decreased. This law states that if the viscosity of the fluid pumped through the centrifugal pump is increased
1. Affinity law 1: This law states that if the speed of the centrifugal pump is increased, the head developed by the pump will also increase in proportion to the square of the speed.NH2 / N1 = (Q2 / Q1) (N2 / N1)2Where: NH2 = Head at speed N2, NH1 = Head at speed N1, Q2 = Flow rate at speed N2, Q1 = Flow rate at speed N1, N2 = New speed of the pump, and N1 = Old speed of the pump.
2. Affinity law 2: This law states that if the diameter of the impeller of the centrifugal pump is increased or decreased, then the head will increase or decrease in proportion to the square of the diameter change.NH2 / NH1 = (D2 / D1)23. Affinity law
3: This law states that if the viscosity of the fluid pumped through the centrifugal pump is increased, the head developed by the pump will decrease in proportion to the square of the viscosity.NH2 / NH1 = (V1 / V2)2Where: NH2 = Head with fluid viscosity V2, NH1 = Head with fluid viscosity V1, V1 = Old fluid viscosity, and V2 = New fluid viscosity.
Learn more about speed at
https://brainly.com/question/6280317
#SPJ11
Air of constant density 1.2 kg/m³ is flowing through a horizontal circular pipe. At a given cross-section of the pipe, the Static Pressure is 70kPa gauge, and the Total Pressure is 90kPa gauge. (a) What is the average velocity of the flow at that pipe cross section if the atmospheric pressure is 100kPa ? Some metres down the pipe, the velocity of the air still have the same value, but the Static Pressure is now 60kPa gauge. (b) What is the decrease in the total pressure between the two measuring stations if the density of the air is assumed constant? (c) Repeat calculations for water with a density of 1000 kg/m³.
The decrease in total pressure between the two measuring stations is 30 kPa.
What is the decrease in total pressure between the two measuring stations?(a) To find the average velocity of the flow at the given pipe cross-section, we can use Bernoulli's equation:
Total Pressure + Dynamic Pressure = Static Pressure + Atmospheric Pressure
Since the pipe is horizontal and the density is constant, the dynamic pressure is zero. Therefore, we have:
Total Pressure = Static Pressure + Atmospheric Pressure
Rearranging the equation, we get:
Dynamic Pressure = Total Pressure - Atmospheric Pressure
Substituting the given values:
Dynamic Pressure = 90 kPa - 100 kPa = -10 kPa
Using the formula for dynamic pressure:
Dynamic Pressure = (1/2) * density * velocity^2
We can rearrange it to solve for velocity:
velocity = sqrt((2 * Dynamic Pressure) / density)
Substituting the values:
velocity = sqrt((2 * (-10 kPa)) / (1.2 kg/m^3))
velocity ≈ sqrt(-16.67) ≈ imaginary (since the value inside the square root is negative)
Therefore, the average velocity of the flow cannot be determined with the given information.
(b) To find the decrease in total pressure between the two measuring stations, we use the same formula:
Total Pressure = Static Pressure + Atmospheric Pressure
The decrease in total pressure is given by:
Pressure decrease = Total Pressure (station 1) - Total Pressure (station 2)
Substituting the given values:
Pressure decrease = 90 kPa - 60 kPa = 30 kPa
Therefore, the decrease in total pressure between the two measuring stations is 30 kPa.
(c) To repeat the calculations for water with a density of 1000 kg/m³, we would need additional information such as the static pressure and total pressure at the given cross-section of the pipe and the static pressure at the second measuring station. Without these values, we cannot calculate the velocity or the pressure decrease for water.
Learn more about decrease
brainly.com/question/2426876
#SPJ11
In the position coordinate, Pſr, θ), r = radial coordinate, and θ=transverse coordinate (True/False).
False. In the position coordinate (r, θ), **r** represents the radial coordinate, while **θ** represents the angular or polar coordinate.
To elaborate, in polar coordinates, a point in a two-dimensional plane is represented using the radial distance from the origin (r) and the angle between the positive x-axis and the line connecting the origin to the point (θ). The radial coordinate (r) determines how far the point is from the origin, while the angular coordinate (θ) specifies the direction or angle at which the point is located with respect to the reference axis. These coordinates are commonly used in mathematics, physics, and engineering to describe positions, velocities, and forces in circular or rotational systems.
Learn more about two-dimensional plane here:
https://brainly.com/question/30268156
#SPJ11
A 15-hp, 220-V, 2000-rpm separately excited dc motor controls a load requiring a torque of 147 , the armature 45 N·m at a speed of 1200 rpm. The field circuit resistance is Rf TL circuit resistance is Ra The field voltage is Vf 0.25 , and the voltage constant of the motor is K₂ 220 V. The viscous friction and no-load losses are negligible. The arma- ture current may be assumed continuous and ripple free. Determine (a) the back emf Eg, (b) the required armature voltage Va, and (c) the rated armature current of the motor. Solution = = = = = = 0.7032 V/A rad/s.
(a) The back emf (Eg) of the motor is 0.7032 V/A rad/s.
(b) The required armature voltage (Va) for the motor is to be determined.
(c) The rated armature current of the motor needs to be calculated.
To determine the back emf (Eg), we can use the formula Eg = K₂ * ω, where K₂ is the voltage constant of the motor and ω is the angular velocity. Given that K₂ is 220 V and ω is 2000 rpm (converted to rad/s), we can calculate Eg as 0.7032 V/A rad/s.
To find the required armature voltage (Va), we need to consider the torque and back emf. The torque equation is T = Kt * Ia, where T is the torque, Kt is the torque constant, and Ia is the armature current. Rearranging the equation, we get Ia = T / Kt. Since the load requires a torque of 147 N·m and Kt is related to the motor characteristics, we would need more information to calculate Va.
To determine the rated armature current, we can use the formula V = Ia * Ra + Eg, where V is the terminal voltage, Ra is the armature circuit resistance, and Eg is the back emf. Given that V is 220 V and Eg is 0.7032 V/A rad/s, and assuming a continuous and ripple-free armature current, we can calculate the rated armature current. However, the given values for Ra and other necessary parameters are missing, making it impossible to provide a specific answer for the rated armature current.
Learn more about back emf here
brainly.com/question/13109636
#SPJ11
Calculate the dimension of the sprues required for the fusion of
a cube of grey cast iron with sand casting technology
Factors such as the size and geometry of the cube, gating system design, casting process parameters, pouring temperature, metal fluidity, and solidification characteristics influence the dimension of the sprues.
What factors influence the dimension of the sprues required for the fusion of a cube of grey cast iron with sand casting technology?The dimension of the sprues required for the fusion of a cube of grey cast iron with sand casting technology depends on various factors, including the size and geometry of the cube, the gating system design, and the casting process parameters. Sprues are channels through which molten metal is introduced into the mold cavity.
To determine the sprue dimension, considerations such as minimizing turbulence, avoiding premature solidification, and ensuring proper filling of the mold need to be taken into account. Factors like pouring temperature, metal fluidity, and solidification characteristics of the cast iron also influence sprue design.
The dimensions of the sprues are typically determined through engineering calculations, simulations, and practical experience. The goal is to achieve efficient and defect-free casting by providing a controlled flow of molten metal into the mold cavity.
It is important to note that without specific details about the cube's dimensions, casting requirements, and process parameters, it is not possible to provide a specific sprue dimension. Each casting application requires a customized approach to sprue design for optimal results.
Learn more about sprues
brainly.com/question/30899946
#SPJ11
Regarding the no-load and the locked-rotor tests of 3-phase induction motor, the correct statement is (). A. The mechanical loss pm can be separated from the total loss in a no-load test. B. The magnetization impedance should be measured when injecting the rated current to the stator in a no-load test. C. The short-circuit impedance should be measured when applying the rated voltage to the stator in a locked-rotor test D. In the locked-rotor test, most of the input power is consumed as the iron loss.
In the locked-rotor test, most of the input power is consumed as the iron loss.
Which statement regarding the no-load and locked-rotor tests of a 3-phase induction motor is incorrect?The statement D is incorrect because in the locked-rotor test of a 3-phase induction motor, most of the input power is consumed as the stator and rotor copper losses, not the iron loss.
During the locked-rotor test, the motor is intentionally locked or mechanically restrained from rotating while connected to a power source.
As a result, the motor draws a high current, and the input power is mainly dissipated as heat in the stator and rotor windings.
This is due to the high current flowing through the windings, resulting in copper losses.
Iron loss, also known as core loss or magnetic loss, occurs when the magnetic field in the motor's core undergoes cyclic changes.
This loss is caused by hysteresis and eddy currents in the core material.
However, in the locked-rotor test, the motor is not rotating, and there is no significant magnetic field variation, so the iron loss is relatively small compared to the copper losses.
Therefore, statement D is incorrect because the majority of the input power in the locked-rotor test is consumed as copper losses, not iron loss.
Learn more about locked-rotor
brainly.com/question/32239974
#SPJ11
please need answer asap
5 5. An aircraft is moving steadily in the air at a velocity of 330 m/s. Determine the speed of sound and Mach number at (a) 300 K (4 marks) (b) 800 K. (4 marks)
The speed of sound can be calculated using the equation v = √(γRT), where v is the speed of sound, γ is the adiabatic index (1.4 for air), R is the gas constant (approximately 287 J/kg*K), and T is the temperature in Kelvin.
(a) At 300 K, the speed of sound can be calculated as v = √(1.4 * 287 * 300) = 346.6 m/s. To find the Mach number, we divide the velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/346.6 ≈ 0.951.
(b) At 800 K, the speed of sound can be calculated as v = √(1.4 * 287 * 800) = 464.7 m/s. The Mach number is obtained by dividing the velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/464.7 ≈ 0.709.
The speed of sound can be calculated using the equation v = √(γRT), where v is the speed of sound, γ is the adiabatic index (1.4 for air), R is the gas constant (approximately 287 J/kg*K), and T is the temperature in Kelvin. For part (a), at a temperature of 300 K, substituting the values into the equation gives v = √(1.4 * 287 * 300) = 346.6 m/s. To find the Mach number, which represents the ratio of the aircraft's velocity to the speed of sound, we divide the given velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/346.6 ≈ 0.951. For part (b), at a temperature of 800 K, substituting the values into the equation gives v = √(1.4 * 287 * 800) = 464.7 m/s. The Mach number is obtained by dividing the given velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/464.7 ≈ 0.709.
Learn more about Mach number here
brainly.com/question/29538118
#SPJ11
Design an active (OPAMP) highpass filter with a high-frequency gain of 5 and a corner frequency of 2 kHz. Use a 0.1µF capacitor in your design.
Verify your design with LTspice. Use the UniversalOpAmp component as OPAMP
To design an active highpass filter with a high-frequency gain of 5 and a corner frequency of 2 kHz using an operational amplifier (OPAMP), we can use a basic configuration called the Sallen-Key filter. Here are the steps to design the filter:
Step 1: Determine the transfer function
The transfer function of the Sallen-Key highpass filter is given by:
H(s) = (sR2C2) / (sR1C1 + 1)
Step 2: Determine the component values
Given that the corner frequency (fc) is 2 kHz, we can set C1 = C2 = 0.1µF.
Using the formula fc = 1 / (2πR1C1), we can solve for R1.
Similarly, using the formula fc = 1 / (2πR2C2), we can solve for R2.
Step 3: Calculate the gain
The desired high-frequency gain is 5. We can set the feedback resistor (Rf) to any value and calculate the input resistor (Rin) using the formula Rin = Rf / (G - 1), where G is the desired high-frequency gain.
Step 4: Verify the design using LTspice
To verify the design, we can simulate the circuit using LTspice. We'll use the UniversalOpAmp component as the operational amplifier in LTspice.
Here is an example circuit schematic for the active highpass filter:
```
* Active Highpass Filter
* Component values
C1 1 0 0.1uF
C2 2 3 0.1uF
R1 1 2 7.96k
R2 2 0 1.99k
Rf 3 0 39.2k
* OPAMP
X1 3 1 0 UniversalOpAmp
* AC analysis
.ac dec 10 1Hz 100kHz
* Plot output
.plot ac V(3)
```
In the LTspice simulation, you can plot the output voltage (V(3)) to see the frequency response of the highpass filter. Make sure to run the AC analysis to obtain the frequency response plot.
Adjust the component values if necessary to achieve the desired high-frequency gain and corner frequency.
Note: This is a basic design example, and further refinements may be required for specific applications or to meet certain design specifications.
Learn more about transfer function here:
https://brainly.com/question/28881525
#SPJ11
Assume that your username is ben and you type the following command: echo \$user is $user. What will be printed on the screen?A. \$user is $user
B. ben is $user
C. $user is ben
D. ben is ben
Assume that your username is ben and you type the following command: echo \$user is $user. ben is $user will be printed on the screen.
In this case, since the dollar sign preceding $user is not escaped with a backslash (\), it will be treated as a variable. The value of the variable $user will be replaced with the username, which is "ben." Therefore, the output will be "ben is $user," where $user is not expanded further since it is within single quotes.
Thus, the correct option is b.
Learn more about command:
https://brainly.com/question/25808182
#SPJ11
A three-phase load is to be powered by a three-wire three-phase Y-connected source having phase voltage of 400 V and operating at 50 Hz. Each phase of the load consists of a parallel combination of a 500Ω resistor, 10 mH inductor, and 1 mF capacitor.
Required:
a. Compute the line current, line voltage, phase current, and power factor of the load if the load is also Y-connected.
b. Rewire the load so that it is -connected and find the same quantities requested in part (a).
The line current, line voltage, phase current, and power factor of the load if it is Y-connected are 0.796 A, 400 V, 0.532 A, and 0.965, respectively.
The phase impedance of the load is given by
Z_p = R + jX_L - jX_C
= 500 + j(2*pi*50*10e-3) - j(1/(2*pi*50))
= 500 + j3.183
The line voltage of the load is equal to the phase voltage, so 400 V. The line current is given by
I_L = V_L / Z_p
= 400 / (500 + j3.183)
= 0.796 + j0.107 A
The phase current is equal to the line current divided by sqrt(3), or
I_p = I_L / sqrt(3)
= 0.532 + j0.072 A
The power factor of the load is given by
pf = cos(theta)
= 0.965
The line current, line voltage, phase current, and power factor of the load if it is Y-connected are 0.796 A, 400 V, 0.532 A, and 0.965, respectively. The power factor is close to unity, indicating that the load is predominantly resistive.
To know more about power factor, visit
https://brainly.com/question/25543272
#SPJ11
Consider an ideal gas-turbine cycle with two stages of compression and two stages of expansion. The pressure ratio across each stage of the compressor is 5 and it is across each stage of the turbine is 8. The air enters each stage of the compressor at 300 K and each stage of the turbine at 1200 K. The cycle has a regenerator with 75 percent effectiveness to improve its overall thermal efficiency. It is assumed that the kinetic and potential energy changes are negligible. The air standard assumptions and constant specific heats are utilised with Cv 0.718 kJ/kg.K and Cp-1.005 kJ/kg.K. Determine: The back work ratio, (ii) The network output, (iii) The thermal efficiency of the cycle.
The gas-turbine cycle is known as Brayton Cycle. It consists of four processes: two isentropic and two constant-pressure processes. The heat transfer occurs during these constant pressure processes (Reheat or Regeneration).
The cycle thermal efficiency is improved with the help of regeneration. Given parameters:Pressure ratio across each stage of compressor, rp = 5Pressure ratio across each stage of turbine, rt = 8Regenerator effectiveness, ε = 0.75Cv = 0.718 kJ/kg.KCp = 1.005 kJ/kg.KTemperature at compressor inlet, T1 = 300 KTemperature at turbine inlet, T3 = 1200 K(i) Back work ratio:To determine back work ratio,First, we need to determine enthalpy of the air at different stages using specific heat equation:Q = m(Cp)(T2 - T1)W = -m(Cp)(T4 - T3).
Srp = (P2/P1)ηC = (P2/P1)^((k-1)/k)Where k = Cp/Cv = 1.4Also,P2/P1 = 5P3/P2 = 5T2/T1 = (P2/P1)^((k-1)/k) = 5^0.4 = 1.827T2 = T1(1.827) = 548.1 KSimilarly, for second stage, T4 = T3(5^0.4) = 1638.3 KSimilarly, for turbine stages,T5/T4 = 1/5^0.4 = 0.5481T5 = 1638.3(0.5481) = 897.2 KSo, the thermal efficiency of the cycle is given by,ηth = 1 - (1/rpt)(1/(1 + εrpt - rprc^γ))where rp = pressure ratio of compressor = 25rt = pressure ratio of turbine = 64ε = effectiveness of the regenerator = 0.75γ = Cp/Cv = 1.4Substituting the values,ηth = 1 - (1/64)(1/(1 + 0.75(64) - 25^(1.4)))ηth = 0.4641 = 46.41%Therefore, the thermal efficiency of the cycle is 46.41%.
To know more about isentropic visit:
https://brainly.com/question/32656653
#SPJ11
Question 3 (a) Give a reason why ceramic package is a better package for housing integrated circuit. (b) For VLSI device plastic molding, state the reason why multipot molding is necessary. (c) State how many levels of packaging strategy are used for interconnection and list down each of them. (d) An integrated circuit has 2,500 gates, its nominal propagation delay for a transistor is 6.0×10 −16
s, its junction to ambient maximum temperature difference is 45 ∘
C, and junction to ambient thermal resistance is 100 ∘
C/W. Calculate the activation energy of each gate of this circuit in electron volt. (e) The typical thermal resistance of plastic epoxy material and ceramic alumina materials are 38 ∘
C/W and 20 ∘
C/W respectively. If you have an integrated circuit that dissipate high power, which package type material would you choose to house this integrated circuit? Explain the reason of your choice.
(a) The ceramic package is a better package for housing integrated circuits because the ceramic is a good thermal conductor, it offers good stability of electrical characteristics over a wide temperature range, it has high strength and resistance to thermal and mechanical stress, and it provides good protection against environmental influences.
(b) The multipot molding process is necessary for VLSI devices because it enables the production of complex structures with a high degree of accuracy and consistency. Multipot molding allows for the creation of multiple layers of interconnects within a single device, which is essential for achieving high-density designs that can accommodate a large number of components within a small footprint.
(c) There are typically four levels of packaging strategy used for interconnection, including : Chip-level packagingModule-level packagingBoard-level packagingSystem-level packaging
(d) The activation energy of each gate of this circuit in electron-volts can be calculated using the formula:Ea = (k*T^2)/(6.0x10^-16)*ln(t/t0)where k is the Boltzmann constant (8.617x10^-5 eV/K), T is the temperature difference between the junction and the ambient environment (45C), t is the nominal propagation delay for a transistor (2,500 gates x 6.0x10^-16 s = 1.5x10^-12 s), and t0 is the reference delay time (1x10^-12 s).
Additionally, ceramic has a higher strength and resistance to mechanical stress, making it more reliable and durable in high-stress environments.
To know more about environmental visit :
https://brainly.com/question/21976584
#SPJ11
A cylindrical-rotor and under-excitation, synchronous generator connected to infinite bus is operated with load the correct statement is ( ). A. The power factor of the synchronous generator is lagging. B. The load is resistive and inductive. C. If the operator of the synchronous generator increases the field current while keeping constant output torque of the prime mover, the armature current will increase. D. If the operator of the synchronous generator reduces the field current while keeping constant output torque of the prime mover, the armature current will increase till the instable operation of the generator.
The correct statement for a cylindrical-rotor and under-excitation synchronous generator connected to an infinite bus and operated with load is: the power factor of the synchronous generator is lagging.
A synchronous generator (alternator) is a machine that generates AC electricity through electromagnetic induction by spinning a rotating magnet around a fixed coil of wire. The synchronicity is essential in this generator since the rotor must rotate at the same speed as the magnetic field generated by the stator winding, creating a constant AC voltage.The terms for the given question are: cylindrical-rotor and under-excitation, synchronous generator, infinite bus, operated with load.
Option A: The power factor of the synchronous generator is lagging. Answer: True
Explanation: The synchronous generator's power factor is lagging since it is under-excited and operated under load.
Option B: The load is resistive and inductive. Answer: False
Explanation: The load may be resistive or inductive or a mixture of both.
Option C: If the operator of the synchronous generator increases the field current while keeping constant output torque of the prime mover, the armature current will increase. Answer: True
Explanation: If the field current is increased, the magnetic field will be strengthened, causing an increase in the armature current.
Option D: If the operator of the synchronous generator reduces the field current while keeping constant output torque of the prime mover, the armature current will increase till the unstable operation of the generator.Answer: False
Explanation: Reducing the field current will cause a drop in the magnetic field strength, resulting in a reduction in the armature current until the generator becomes unstable.
To know more about generator visit:
https://brainly.com/question/12841996
#SPJ11
A bipolar junction transistor operates as an amplifier by(1 O Applying bias from high impedance loop to low impedance loop. O Transferring current from low impedance to high impedance loop O Transferring current from high impedance to low impedance loop O Applying bias from low impedance to high impedance loop
A bipolar junction transistor is a kind of transistor that can be used to amplify electrical signals.
The transistor is made up of three regions with alternating p-type and n-type doping materials. The three layers of a BJT are: Collector Base Emitter A bipolar junction transistor is capable of operating as an amplifier because it has a current-controlled current source. In an NPN transistor, this means that a current flowing into the base terminal controls a larger current flowing out of the collector terminal.
As a result, small variations in the base current can cause large variations in the collector current. The answer to the given question is that a bipolar junction transistor operates as an amplifier by transferring current from low impedance to high impedance loop.
To know more about bipolar visit:-
https://brainly.com/question/31835767
#SPJ11
An iron hub of length 450 mm has an outer and inner diameter of 650 mm and 400 mm respectively. A solid steel shaft of diameter 400 mm is pressed fit into the iron hub. The tangential stress at the mating surface is 35MPa and the coefficient of friction at the mating surface is 0.17. The modulus of elasticity for the iron and steel are 100GPa and 200GPa respectively, and the Poisson's ratios for iron and steel are 0.2 and 0.3 respectively. Calculate: i) The maximum interference ii) The torque transmitted by the shaft
Maximum interferenceThe interference fit is used to get an integral unit of the shaft and hub, diameter a negligible relative motion between them. .
The amount of interference is expressed as the radial distance between the outer diameter of the shaft and the inner diameter of the hole. The maximum stress is also called the working stress. It is defined as the maximum stress which is acceptable for the particular design. It depends on the yield strength of the material.
The maximum interference is given by,
δmax=τ / [π/2 (τ-σ) (1-µiµs) D](1/2)
Whereδmax
= Maximum Interferenceτ
= Shear stressµi
= Poisson's ratio for Ironµs
= Poisson's ratio for Steelσ
= Compressive stressD
= Outer Diameter
= 650 mm - 400 mm
= 250 mmσ = τ/µi
= 35 MPa / 0.2
= 175 MPa
Substituting the given values, we get,δmax
=35 / [π/2 (35-175) (1-0.17 x 0.2 x 0.3) x 250](1/2
)= 0.269 mmii)
Torque transmitted by the shaftThe torque transmitted by the shaft is given by,
T = τmπ/2 (D^3 - d^3)
Whereτm = Maximum Shear Stress
= τ = 35 MPaD = Outer Diameter
= 650 mm - 400 mm
= 250 mmd
= Inner Diameter of the shaft
= 400 mmTorque transmitted,
T = 35 x π/2 (250^3 - 400^3)
= 5.372 x 10^7 N-mm (Approximately)
Therefore, the maximum interference is 0.269 mm (approx) and the torque transmitted by the shaft is 5.372 x 10^7 N-mm (Approximately).
To know more about diameter visit:
https://brainly.com/question/1294515
#SPJ11