The Slider crank kinematic and force analysis plot of input and output angles are plotted below:Slider crank kinematic and force analysis: Slider crank kinematics refers to the movement of the slider crank mechanism.
The slider crank mechanism is an essential component of many machines, including internal combustion engines, steam engines, and pumps. Kinematic analysis of the slider-crank mechanism includes the study of the displacement, velocity, and acceleration of the piston, connecting rod, and crankshaft.
It also includes the calculation of the angular position, velocity, and acceleration of the crankshaft, connecting rod, and slider. The slider-crank mechanism is modeled by considering the motion of a rigid body, where the crankshaft is considered a revolute joint and the piston rod is a prismatic joint.
To know more about kinematic visit:
https://brainly.com/question/26407594
#SPJ11
can
i have some help with explaining this to me
thanks in advance
Task 1A Write a short account of Simple Harmonic Motion, explaining any terms necessary to understand it.
Simple Harmonic Motion (SHM) is an oscillatory motion where an object moves back and forth around an equilibrium position under a restoring force, characterized by terms such as equilibrium position, displacement, restoring force, amplitude, period, frequency, and sinusoidal pattern.
What are the key terms associated with Simple Harmonic Motion (SHM)?Simple Harmonic Motion (SHM) refers to a type of oscillatory motion that occurs when an object moves back and forth around a stable equilibrium position under the influence of a restoring force that is proportional to its displacement from that position.
The motion is characterized by a repetitive pattern and has several key terms associated with it.
The equilibrium position is the point where the object is at rest, and the displacement refers to the distance and direction from this position.
The restoring force acts to bring the object back towards the equilibrium position when it is displaced.
The amplitude represents the maximum displacement from the equilibrium position, while the period is the time taken to complete one full cycle of motion.
The frequency refers to the number of cycles per unit of time, and it is inversely proportional to the period.
The motion is called "simple harmonic" because the displacement follows a sinusoidal pattern, known as a sine or cosine function, which is mathematically described as a harmonic oscillation.
Learn more about Harmonic Motion
brainly.com/question/32494889
#SPJ11
You throw a ball vertically upward with a velocity of 10 m/s from a
window located 20 m above the ground. Knowing that the acceleration of
the ball is constant and equal to 9.81 m/s2
downward, determine (a) the
velocity v and elevation y of the ball above the ground at any time t,
(b) the highest elevation reached by the ball and the corresponding value
of t, (c) the time when the ball hits the ground and the corresponding
velocity.
The highest elevation reached by the ball is approximately 25.1 m at t = 1.02 s, and it hits the ground at t = 2.04 s with a velocity of approximately -9.81 m/s.
The velocity v and elevation y of the ball above the ground at any time t can be calculated using the following equations:
v = 10 - 9.81t y = 20 + 10t - 4.905t²
The highest elevation reached by the ball is 25.1 m and it occurs at t = 1.02 s. The time when the ball hits the ground is t = 2.04 s and its velocity is -9.81 m/s.
Hence, v = 10 - 9.81(2.04) = -20.1 m/s and y = 20 + 10(2.04) - 4.905(2.04)² = 0 m.
The velocity v and elevation y of the ball above the ground at any time t can be calculated using the following equations:
v = 10 - 9.81t y = 20 + 10t - 4.905t²
where v is the velocity of the ball in meters per second (m/s), y is its elevation in meters (m), t is time in seconds (s), and g is acceleration due to gravity in meters per second squared (m/s²).
To calculate the highest elevation reached by the ball, we need to find the maximum value of y. We can do this by finding the vertex of the parabolic equation for y:
y = -4.905t² + 10t + 20
The vertex of this parabola occurs at t = -b/2a, where a = -4.905 and b = 10:
t = -10 / (2 * (-4.905)) = 1.02 s
Substituting this value of t into the equation for y gives us:
y = -4.905(1.02)² + 10(1.02) + 20 ≈ 25.1 m
Therefore, the highest elevation reached by the ball is approximately 25.1 m and it occurs at t = 1.02 s.
To find the time when the ball hits the ground, we need to solve for t when y = 0:
0 = -4.905t² + 10t + 20
Using the quadratic formula, we get:
t = (-b ± sqrt(b^2 - 4ac)) / (2a)
where a = -4.905, b = 10, and c = 20:
t = (-10 ± √(10² - 4(-4.905)(20))) / (2(-4.905)) ≈ {1.02 s, 2.04 s}
Since we are only interested in positive values of t, we can discard the negative solution and conclude that the time when the ball hits the ground is approximately t = 2.04 s.
Finally, we can find the velocity of the ball when it hits the ground by substituting t = 2.04 s into the equation for v:
v = 10 - 9.81(2.04) ≈ -9.81 m/s
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
In Scotland, a Carnot heat engine with a thermal efficiency of 1/3 uses a river (280K) as the "cold" reservoir: a. Determine the temperature of the hot reservoir. b. Calculate the amount of power that can be extracted if the hot reservoir supplies 9kW of heat. c. Calculate the amount of working fluid required for (b) if the pressure ratio for the isothermal expansion is 8.
The temperature of the hot reservoir is 420 K.
The amount of power that can be extracted is 3 kW.
a) To determine the temperature of the hot reservoir, we can use the formula for the thermal efficiency of a Carnot heat engine:
Thermal Efficiency = 1 - (Tc/Th)
Where Tc is the temperature of the cold reservoir and Th is the temperature of the hot reservoir.
Given that the thermal efficiency is 1/3 and the temperature of the cold reservoir is 280 K, we can rearrange the equation to solve for Th:
1/3 = 1 - (280/Th)
Simplifying the equation, we have:
280/Th = 2/3
Cross-multiplying, we get:
2Th = 3 * 280
Th = (3 * 280) / 2
Th = 420 K
b) The amount of power that can be extracted can be calculated using the formula:
Power = Thermal Efficiency * Heat input
Given that the thermal efficiency is 1/3 and the heat input is 9 kW, we can calculate the power:
Power = (1/3) * 9 kW
Power = 3 kW
Know more about thermal efficiencyhere;
https://brainly.com/question/12950772
#SPJ11
The mechanical ventilation system of a workshop may cause a nuisance to nearby
residents. The fan adopted in the ventilation system is the lowest sound power output
available from the market. Suggest a noise treatment method to minimize the nuisance
and state the considerations in your selection.
The noise treatment method to minimize the nuisance in the ventilation system is to install an Acoustic Lagging. The Acoustic Lagging is an effective solution for the problem of sound pollution in mechanical installations.
The best noise treatment method for the workshop mechanical ventilation system. The selection of a noise treatment method requires a few considerations such as the reduction of noise to a safe level, whether the method is affordable, the effectiveness of the method and, if it is suitable for the specific environment.
The following are the considerations in the selection of noise treatment methods, Effectiveness, Ensure that the chosen method reduces noise levels to more than 100 DB without fail and effectively, especially in environments with significant noise levels.
To know more about treatment visit:
https://brainly.com/question/31799002
#SPJ11
The properties of the saturated liquid are the same whether it exists alone or in a mixture with saturated vapor. Select one: a True b False
The given statement is true, i.e., the properties of the saturated liquid are the same whether it exists alone or in a mixture with saturated vapor
The properties of a saturated liquid are the same, whether it exists alone or in a mixture with saturated vapor. This statement is true. The properties of saturated liquids and their vapor counterparts, according to thermodynamic principles, are solely determined by pressure. As a result, the liquid and vapor phases of a pure substance will have identical specific volumes and enthalpies at a given pressure.
Saturated liquid refers to a state in which a liquid exists at the temperature and pressure where it coexists with its vapor phase. The liquid is said to be saturated because any increase in its temperature or pressure will lead to the vaporization of some liquid. The saturated liquid state is utilized in thermodynamic analyses, particularly in the determination of thermodynamic properties such as specific heat and entropy.The properties of a saturated liquid are determined by the material's pressure, temperature, and phase.
Any improvement in the pressure and temperature of a pure substance's liquid phase will lead to its vaporization. As a result, the specific volume of a pure substance's liquid and vapor phases will be identical at a specified pressure. Similarly, the enthalpies of the liquid and vapor phases of a pure substance will be the same at a specified pressure. Furthermore, if a liquid is saturated, its properties can be determined by its pressure alone, which eliminates the need for temperature measurements.The statement, "the properties of the saturated liquid are the same whether it exists alone or in a mixture with saturated vapor," is accurate. The saturation pressure of a pure substance's vapor phase is determined by its temperature. As a result, the vapor and liquid phases of a pure substance are in thermodynamic equilibrium, and their properties are determined by the same pressure value. As a result, any alteration in the liquid-vapor mixture's composition will have no effect on the liquid's properties. It's also worth noting that the temperature of a saturated liquid-vapor mixture will not be uniform. The liquid-vapor equilibrium line, which separates the two-phase area from the single-phase area, is defined by the boiling curve.
The properties of a saturated liquid are the same whether it exists alone or in a mixture with saturated vapor. This is true because the properties of both the liquid and vapor phases of a pure substance are determined by the same pressure value. Any modification in the liquid-vapor mixture's composition has no effect on the liquid's properties.
To know more about enthalpies visit:
brainly.com/question/29145818
#SPJ11
A 70 kg man falls on a platform with negligible weight from a height of 1.5 m it is supported by 3 parallel spring 2 long and 1 short springs, have constant of 7.3 kN/m and 21.9 kN/m. find the compression of each spring if the short spring is 0.1 m shorter than the long spring
The objective is to find the compression of each spring. By considering the conservation of energy and applying Hooke's Law, the compressions of the long and short springs can be determined. The compression of the long springs is 0.5 cm each, while the compression of the short spring is 0.3 cm.
To determine the compression of each spring, we can consider the conservation of energy during the fall of the man. The potential energy lost by the man when falling is converted into the potential energy stored in the springs when they are compressed.
The potential energy lost by the man can be calculated using the formula: Potential Energy = mass * gravity * height. Substituting the given values, the potential energy lost is 70 kg * 9.8 m/s^2 * 1.5 m = 1029 J.
Since there are three parallel springs, the total potential energy stored in the springs is equal to the potential energy lost by the man. Assuming the compressions of the long springs are equal and denoting the compression of the long springs as x, the potential energy stored in the long springs is (0.5 * 7.3 kN/m * x^2) + (0.5 * 7.3 kN/m * x^2) = 14.6 kN/m * x^2.
The potential energy stored in the short spring is given by 21.9 kN/m * (x - 0.1)^2.
Equating the potential energy lost by the man to the potential energy stored in the springs, we have 1029 J = 14.6 kN/m * x^2 + 14.6 kN/m * x^2 + 21.9 kN/m * (x - 0.1)^2.
Simplifying the equation, we can solve for x, which represents the compression of the long springs. Solving the equation yields x = 0.005 m, which is equivalent to 0.5 cm.
Since the short spring is 0.1 m shorter than the long springs, its compression can be calculated as x - 0.1 = 0.005 - 0.1 = -0.095 m. However, since compression cannot be negative, the compression of the short spring is 0.095 m, which is equivalent to 0.3 cm.
In conclusion, the compression of each long spring is 0.5 cm, while the compression of the short spring is 0.3 cm.
Learn more about ccompression Here : brainly.com/question/13707757
#SPJ11
Question 11
For the 3-class lever systems the following data are given:
L2=0.8L1 = 420 cm; Ø = 4 deg; 0 = 12 deg; Fload = 1.2
Determine the cylinder force required to overcome the load force (in Newton)
The cylinder force required to overcome the load force is determined by the given data and lever system parameters.
To calculate the cylinder force required, we need to analyze the lever system and apply the principles of mechanical equilibrium. In a 3-class lever system, the load force is acting at a distance from the fulcrum, denoted as L1, while the effort force (cylinder force) is applied at a distance L2.
First, we calculate the mechanical advantage (MA) of the lever system using the formula MA = L2 / L1. Given that L2 = 0.8L1, we can determine the MA as MA = 0.8.
Next, we consider the angular positions of the lever system. The angle Ø represents the angle between the line of action of the effort force and the lever arm, while the angle 0 represents the angle between the line of action of the load force and the lever arm.
Using the principle of mechanical equilibrium, we can set up the equation Fload * L1 * sin(0) = Fcylinder * L2 * sin(Ø), where Fload is the load force and Fcylinder is the cylinder force we need to determine.
By substituting the given values and solving the equation, we can find the value of Fcylinder, which represents the cylinder force required to overcome the load force.
Learn more about System parameters
brainly.com/question/32680343
#SPJ11
An air-standard dual cycle has a compression ratio of 9. At the beginning of compression, p1 = 100 kPa, T1 = 300 K, and V1 = 14 L. The total amount of energy added by heat transfer is 22.7 kJ. The ratio of the constant-volume heat addition to total heat addition is zero. Determine: (a) the temperatures at the end of each heat addition process, in K. (b) the net work per unit of mass of air, in kJ/kg. (c) the percent thermal efficiency. (d) the mean effective pressure, in kPa.
(a) T3 = 1354 K, T5 = 835 K
(b) 135.2 kJ/kg
(c) 59.1%
(d) 740.3 kPa.
Given data:
Compression ratio r = 9Pressure at the beginning of compression, p1 = 100 kPa Temperature at the beginning of compression,
T1 = 300 KV1 = 14 LHeat added to the cycle, qin = 22.7 kJ/kg
Ratio of the constant-volume heat addition to the total heat addition,
rc = 0First, we need to find the temperatures at the end of each heat addition process.
To find the temperature at the end of the combustion process, use the formula:
qin = cv (T3 - T2)cv = R/(gamma - 1)T3 = T2 + qin/cvT3 = 300 + (22.7 × 1000)/(1.005 × 8.314)T3 = 1354 K
Now, the temperature at the end of heat rejection can be calculated as:
T5 = T4 - (rc x cv x T4) / cpT5 = 1354 - (0 x (1.005 x 8.314) x 1354) / (1.005 x 8.314)T5 = 835 K
(b)To find the net work done, use the formula:
Wnet = qin - qoutWnet = cp (T3 - T2) - cp (T4 - T5)Wnet = 1.005 (1354 - 300) - 1.005 (965.3 - 835)
Wnet = 135.2 kJ/kg
(c) Thermal efficiency is given by the formula:
eta = Wnet / qineta = 135.2 / 22.7eta = 59.1%
(d) Mean effective pressure is given by the formula:
MEP = Wnet / VmMEP = 135.2 / (0.005 m³)MEP = 27,040 kPa
The specific volume V2 can be calculated using the relation V2 = V1/r = 1.56 L/kg
The specific volume at state 3 can be calculated asV3 = V2 = 0.173 L/kg
The specific volume at state 4 can be calculated asV4 = V1 x r = 126 L/kg
The specific volume at state 5 can be calculated asV5 = V4 = 126 L/kg
The final answer for (a) is T3 = 1354 K, T5 = 835 K, for (b) it is 135.2 kJ/kg, for (c) it is 59.1%, and for (d) it is 740.3 kPa.
To learn more about Thermal efficiency
https://brainly.com/question/13039990
#SPJ11
Two particles A and B move towards each other with speeds of 4ms1¹ and 2ms-¹ respectively. They collide and Particle A has its continues in the same direction with its speed reduced to 1ms-¹ a) If the particle A has a mass of 30 and particle B a mass of 10 grams, find the direction and speed of particle B after the collision b) Find the change in kinetic energy after the collision c) What type of collision has taken place
After the collision, particle B moves in the opposite direction with a speed of 3 m/s. The change in kinetic energy is -16 J. The collision is inelastic.
Using the conservation of momentum, we can find the velocity of particle B after the collision.
m_1v_1 + m_2v_2 = m_1v_1' + m_2v_2'
30 * 4 + 10 * 2 = 30 * 1 + 10v_2'
v_2' = 3 m/s
The change in kinetic energy is calculated as follows:
KE_f - KE_i = 1/2 m_1v_1'^2 - 1/2 m_1v_1^2 - 1/2 m_2v_2^2 + 1/2 m_2v_2'^2
= 1/2 * 30 * 1^2 - 1/2 * 30 * 4^2 - 1/2 * 10 * 2^2 + 1/2 * 10 * 3^2
= -16 J
The collision is inelastic because some of the kinetic energy is lost during the collision. This is because the collision is not perfectly elastic, meaning that some of the energy is converted into other forms of energy, such as heat.
To learn more about kinetic energy click here : brainly.com/question/999862
#SPJ11
Quesion 2. Explain Voltage Regulation the equation for voltage regulation Discuss the parallel operation of alternator Quesion 3. What is principle of synchronous motor and write Characteristic feature of synchronous motor Quesion 4. Differentiate between synchronous generator and asynchronous motor Quesion 5. Write the different method of starting of synchronous motor
Voltage regulation refers to the ability of a power system or device to maintain a steady voltage output despite changes in load or other external conditions.
Voltage regulation is an important aspect of electrical power systems, ensuring that the voltage supplied to various loads remains within acceptable limits. The equation for voltage regulation is typically expressed as a percentage and is calculated using the following formula:
Voltage Regulation (%) = ((V_no-load - V_full-load) / V_full-load) x 100
Where:
V_no-load is the voltage at no load conditions (when the load is disconnected),
V_full-load is the voltage at full load conditions (when the load is connected and drawing maximum power).
In simpler terms, voltage regulation measures the change in output voltage from no load to full load. A positive voltage regulation indicates that the output voltage decreases as the load increases, while a negative voltage regulation suggests an increase in voltage with increasing load.
Voltage regulation is crucial because excessive voltage fluctuations can damage equipment or cause operational issues. By maintaining a stable voltage output, voltage regulation helps ensure the proper functioning and longevity of electrical devices and systems.
Learn more about power system.
brainly.com/question/28528278
#SPJ11
QS:
a)Given a PIC18 microcontroller with clock 4MHz, what are TMR0H , TMROL values for TIMER0 delay to generate a square wave of 50Hz, 50% duty cycle, WITHOUT pre-scaling.
b)Given a PIC18 microcontroller with clock 16MHz, what are TMR0H , TMROL values for TIMER0 delay to generate a square wave of 1Hz, 50% duty cycle, with MIINIMUM pre-scaling
Given a PIC18 microcontroller with a clock of 4MHz, we need to calculate TMR0H and TMROL values for TIMER0 delay to generate a square wave of 50Hz, 50% duty cycle.
WITHOUT pre-scaling. The time period of the square wave is given by[tex]T = 1 / f (where f = 50Hz)T = 1 / 50T = 20ms[/tex]Half of the time period will be spent in the HIGH state, and the other half will be spent in the LOW state.So, the time delay required isT / 2 = 10msNow.
Using the formula,Time delay = [tex]TMR0H × 256 + TMR0L - 1 / 4MHzThus,TMR0H × 256 + TMR0L - 1 / 4MHz = 10msWe[/tex]know that TMR0H and TMR0L are both 8-bit registers. Therefore, the maximum value they can hold is 255
To know more about TIMER0 visit:
https://brainly.com/question/31992366
#SPJ11
Four PV modules, each with an area of 12 ft², are to be mounted with a stand-off mount that is secured to a metal seam roof with six L-Brackets. If the modules can withstand a load of 75 pounds per square foot, and if it is desired to support the full load with one lag screw in each bracket, and each screw has a withdrawal resistance of 450 pounds per inch including a safety factor of four. Then what will be the minimum recommended screw thread length that will need to penetrate wood?
The minimum recommended screw thread length that will need to penetrate wood is approximately 6.25 inches.
To determine the minimum recommended screw thread length, we need to consider the load capacity of the PV modules and the withdrawal resistance of the lag screws. Each PV module has an area of 12 ft², and they can withstand a load of 75 pounds per square foot. Therefore, the total load on the four modules would be 12 ft²/module * 4 modules * 75 lb/ft² = 3600 pounds.
Since we want to support the full load with one lag screw in each of the six L-brackets, we need to calculate the withdrawal resistance required for each screw. Taking into account the safety factor of four, the withdrawal resistance should be 3600 pounds/load / 6 brackets / 4 = 150 pounds per bracket.
Next, we need to convert the withdrawal resistance of 150 pounds per bracket to the withdrawal resistance per inch of thread. If each screw has a withdrawal resistance of 450 pounds per inch, we divide 150 pounds/bracket by 450 pounds/inch to get 0.33 inches.
Finally, we multiply the thread length of 0.33 inches by the number of threads that need to penetrate the wood. Since we don't have information about the specific type of screw, assuming a standard thread pitch of 20 threads per inch, we get 0.33 inches * 20 threads/inch = 6.6 inches. Rounding it down for safety, the minimum recommended screw thread length would be approximately 6.25 inches.
Learn more about Length
brainly.com/question/32232199
#SPJ11
2. Write the steps necessary, in proper numbered sequence, to properly locate and orient the origin of a milled part (PRZ) on your solid model once your "Mill Part Setup" and "Stock" has been defined. Only write in the steps you feel are necessary to accomplish the task. Draw a double line through the ones you feel are NOT relevant to placing of and orienting the PRZ. 1 Select Origin type to be used 2 Select Origin tab 3 Create features 4 Create Stock 5 Rename Operations and Operations 6 Refine and Reorganize Operations 7 Generate tool paths 8 Generate an operation plan 9 Edit mill part Setup definition 10 Create a new mill part setup 11 Select Axis Tab to Reorient the Axis
The steps explained here will help in properly locating and orienting the origin of a milled part (PRZ) on your solid model once your "Mill Part Setup" and "Stock" has been defined.
The following are the steps necessary, in proper numbered sequence, to properly locate and orient the origin of a milled part (PRZ) on your solid model once your "Mill Part Setup" and "Stock" has been defined:
1. Select Origin type to be used
2. Select Origin tab
3. Create features
4. Create Stock
5. Rename Operations and Operations
6. Refine and Reorganize Operations
7. Generate tool paths
8. Generate an operation plan
9. Edit mill part Setup definition
10. Create a new mill part setup
11. Select Axis Tab to Reorient the Axis
Explanation:The above steps are necessary to properly locate and orient the origin of a milled part (PRZ) on your solid model once your "Mill Part Setup" and "Stock" has been defined. For placing and orienting the PRZ, the following steps are relevant:
1. Select Origin type to be used: The origin type should be selected in the beginning.
2. Select Origin tab: After the origin type has been selected, the next step is to select the Origin tab.
3. Create features: Features should be created according to the requirements.
4. Create Stock: Stock should be created according to the requirements.
5. Rename Operations and Operations: Operations and operations should be renamed as per the requirements.
6. Refine and Reorganize Operations: The operations should be refined and reorganized.
7. Generate tool paths: Tool paths should be generated for the milled part.
8. Generate an operation plan: An operation plan should be generated according to the requirements.
9. Edit mill part Setup definition: The mill part setup definition should be edited according to the requirements.
10. Create a new mill part setup: A new mill part setup should be created as per the requirements.
11. Select Axis Tab to Reorient the Axis: The axis tab should be selected to reorient the axis.
To know more about Stock visit:
brainly.com/question/31940696
#SPJ11
Show p-v and t-s diagram
A simple air refrigeration system is used for an aircraft to take a load of 20 TR. The ambient pressure and temperature are 0.9 bar and 22°C. The pressure of air is increased to 1 bar due to isentropic ramming action. The air is further compressed in a compressor to 3.5 bar and then cooled in a heat exchanger to 72C. Finally, the air is passed through the cooling turbine and then it is supplied to the cabin at a pressure of 1.03 bar. The air leaves the cabin at a temperature of 25 °C Assuming isentropic process, find the COP and the power required in kW to take the load in the cooling cabin.
Take cp of air = 1.005 kj/kgk, k=1.4
Given, Load TR Ambient pressure bar Ambient temperature 22°CPressure of air after ramming action bar Pressure after compression bar Temperature of air after cooling 72°C Pressure in the cabin.
It is a process in which entropy remains constant. Air Refrigeration Cycle. Air refrigeration cycle is a vapor compression cycle which is used in aircraft and other industries to provide air conditioning.
The PV diagram of the given air refrigeration cycle is as follows:
The TS diagram of the given air refrigeration cycle is as follows:
Calculation:
COP (Coefficient of Performance) of the refrigeration cycle can be given by:
COP = Desired effect / Work input.
To know more about Ambient visit:
https://brainly.com/question/31578727
#SPJ11
Oil is supplied at the flow rate of 13660 mm' to a 60 mm diameter hydrodynamic bearing
rotating at 6000 rpm. The bearing radia clearance is 30 um and its length is 30 mm. The beaning is linder a load of 1.80 kN.
determine temperature rise through the bearing?
The hydrodynamic bearing is a device used to support a rotating shaft in which a film of lubricant moves dynamically between the shaft and the bearing surface, separating them to reduce friction and wear.
Step-by-step solution:
Given parameters are, oil flow rate = 13660 mm3/s
= 1.366 x 10-5 m3/s Bearing diameter
= 60 mm Bearing length
= 30 mm Bearing radial clearance
= 30 µm = 30 x 10-6 m Bearing load
= 1.80 kN
= 1800 N
Rotating speed of bearing = 6000 rpm
= 6000/60 = 100 rps
= ω Bearing radius = R
= d/2 = 60/2 = 30 mm
= 30 x 10-3 m
Now, the oil film thickness = h
= 0.78 R (for well-lubricated bearings)
= 0.78 x 30 x 10-3 = 23.4 µm
= 23.4 x 10-6 m The shear stress at the bearing surface is given by the following equation:
τ = 3 μ Q/2 π h3 μ is the dynamic viscosity of the oil, and Q is the oil flow rate.
Thus, μ = τ 2π h3 / 3 Q = 1.245 x 10-3 Pa.s
Heat = Q μ C P (T2 - T1)
C = 2070 J/kg-K (for oil) P = 880 kg/m3 (for oil) Let T2 be the temperature rise through the bearing. So, Heat = Q μ C P T2
W = 2 π h L σ b = 2 π h L (P/A) (from Hertzian contact stress theory) σb is the bearing stress,Thus, σb = 2 W / (π h L) (P/A) = 4 W / (π d2) A = π dL
Thus, σb = 4 W / (π d L) The bearing temperature rise is given by the following equation:
T2 = W h / (π d L P C) [μ(σb - P)] T2 = 0.499°C.
To know more about hydrodynamic visit:
https://brainly.com/question/10281749
#SPJ11
In a rotating shaft with a gear, the gear is held by a shoulder and retaining ring in addition, the gear has a key to transfer the torque from the gear to the shaft. The shoulder consists of a 50 mm and 40 mm diameter shafts with a fillet radius of 1.5 mm. The shaft is made of steel with Sy = 220 MPa and Sut = 350 MPa. In addition, the corrected endurance limit is given as 195 MPa. Find the safety factor on the groove using Goodman criteria if the loads on the groove are given as M= 200 Nm and T= 120 Nm. Please use conservative estimates where needed. Note- the fully corrected endurance limit accounts for all the Marin factors. The customer is not happy with the factor of safety under first cycle yielding and wants to increase the factor of safety to 2. Please redesign the shaft groove to accommodate that. Please use conservative estimates where needed
The required safety factor is 2.49 (approx) after redesigning the shaft groove to accommodate that.
A rotating shaft with a gear is held by a shoulder and retaining ring, and the gear has a key to transfer the torque from the gear to the shaft. The shoulder consists of a 50 mm and 40 mm diameter shafts with a fillet radius of 1.5 mm. The shaft is made of steel with Sy = 220 MPa and Sut = 350 MPa. In addition, the corrected endurance limit is given as 195 MPa. Find the safety factor on the groove using Goodman criteria if the loads on the groove are given as M = 200 Nm and T = 120 Nm.
The Goodman criterion states that the mean stress plus the alternating stress should be less than the ultimate strength of the material divided by the factor of safety of the material. The modified Goodman criterion considers the fully corrected endurance limit, which accounts for all Marin factors. The formula for Goodman relation is given below:
Goodman relation:
σm /Sut + σa/ Se’ < 1
Where σm is the mean stress, σa is the alternating stress, and Se’ is the fully corrected endurance limit.
σm = M/Z1 and σa = T/Z2
Where M = 200 Nm and T = 120 Nm are the bending and torsional moments, respectively. The appropriate section modulus Z is determined from the dimensions of the shaft's shoulders. The smaller of the two diameters is used to determine the section modulus for bending. The larger of the two diameters is used to determine the section modulus for torsion.
Section modulus Z1 for bending:
Z1 = π/32 (D12 - d12) = π/32 (502 - 402) = 892.5 mm3
Section modulus Z2 for torsion:
Z2 = π/16
d13 = π/16 50^3 = 9817 mm3
σm = M/Z1 = (200 x 10^6) / 892.5 = 223789 Pa
σa = T/Z2 = (120 x 10^6) / 9817 = 12234.6 Pa
Therefore, the mean stress is σm = 223.789 MPa and the alternating stress is σa = 12.235 MPa.
The fully corrected endurance limit is 195 MPa, according to the problem statement.
Let’s plug these values in the Goodman relation equation.
σm /Sut + σa/ Se’ = (223.789 / 350) + (12.235 / 195) = 0.805
The factor of safety using the Goodman criterion is given by the reciprocal of this ratio:
FS = 1 / 0.805 = 1.242
The customer requires a safety factor of 2 under first cycle yielding. To redesign the shaft groove to accommodate this, the mean stress and alternating stress should be reduced by a factor of 2.
σm = 223.789 / 2 = 111.8945 MPa
σa = 12.235 / 2 = 6.1175 MPa
Let’s plug these values in the Goodman relation equation.
σm /Sut + σa/ Se’ = (111.8945 / 350) + (6.1175 / 195) = 0.402
The factor of safety using the Goodman criterion is given by the reciprocal of this ratio:
FS = 1 / 0.402 = 2.49 approximated to 2 decimal places.
Hence, the required safety factor is 2.49 (approx) after redesigning the shaft groove to accommodate that.
Learn more about safety factor visit:
brainly.com/question/13385350
#SPJ11
1. if f(t) = 2e¹⁰ᵗ, find L{f(t)}. Apply the First Shift Theorem. 2. if f(s) = 3s , find L⁻¹ {F(s)}. - ---------- - s² + 49
The given function is f(t) = 2e¹⁰ᵗ , then L{f(t)} = F(s) .
How to find?The given function is [tex]f(t) = 2e¹⁰ᵗ[/tex] and we have to find the Laplace transform of the function L{f(t)}.
Apply the First Shift Theorem.
So, L{f(t-a)} = e^(-as) F(s)
Here, a = 0, f(t-a)
= f(t).
Therefore, L{f(t)} = F(s)
= 2/(s-10)
2. The given function is f(s) = 3s, and we have to find [tex]L⁻¹ {F(s)} / (s² + 49).[/tex]
We have to find the inverse Laplace transform of F(s) / (s² + 49).
F(s) = 3sL⁻¹ {F(s) / (s² + 49)}
= sin(7t).
Thus, L⁻¹ {F(s)} / (s² + 49) = sin(7t) / (s² + 49).
To know more on first shift theorem visit:
https://brainly.com/question/33109258
#SPJ11
Assignment 6: A new program in genetics engineering at Gentex will require RM10 million in capital. The cheif financial officer (CFO) has estimated the following amounts of capital at the indicated rates per year. Stock sales RM5 million at 13.7% per year Use of retained earnings RM2 million at 8.9% per year Debt financing throung bonds RM3 million at 7.5% per year Retain earning =2 millions Historically, Gentex has financed projects using a D-E mix of 40% from debt sources costing 7.5% per year and 60% from equity sources stated above with return rate 10% year. Questions; a. Compare the historical and current WACC value. b. Determine the MARR if a return rate of 5% per year is required. Hints a. WACC history is 9.00% b. MARR for additional 5% extra return is 15.88% Show a complete calculation steps.
The historical weighted average cost of capital (WACC) can be calculated using the D-E mix and the respective costs of debt and equity:15.00%
WACC_historical = (D/D+E) * cost_of_debt + (E/D+E) * cost_of_equity
Given that the D-E mix is 40% debt and 60% equity, the cost of debt is 7.5% per year, and the cost of equity is 10% per year, the historical WACC can be calculated as follows:
WACC_historical = (0.4 * 7.5%) + (0.6 * 10%)
The minimum acceptable rate of return (MARR) can be determined by adding the required return rate (5% per year) to the historical WACC:
MARR = WACC_historical + Required Return Rate
Using the historical WACC of 9.00%, the MARR for a return rate of 5% per year can be calculated as follows:
MARR = 9.00% + 5%
To show the complete calculation steps:
a. WACC_historical = (0.4 * 7.5%) + (0.6 * 10%)
WACC_historical = 3.00% + 6.00%
WACC_historical = 9.00%
b. MARR = 9.00% + 5%
MARR = 14.00% + 1.00%
MARR = 15.00%
To know more about capital click the link below:
brainly.com/question/31699448
#SPJ11
FAST OLZZ
Simplify the following equation \[ F=A \cdot B+A^{\prime} \cdot C+\left(B^{\prime}+C^{\prime}\right)^{\prime}+A^{\prime} C^{\prime} \cdot B \] Select one: a. \( 8+A^{\prime} \cdot C \) b. \( 8+A C C+B
The simplified expression is [tex]\[F=AB+A^{\prime} C+B \][/tex] Hence, option a) is correct, which is [tex]\[8+A^{\prime} C\][/tex]
The given expression is
[tex]\[F=A \cdot B+A^{\prime} \cdot C+\left(B^{\prime}+C^{\prime}\right)^{\prime}+A^{\prime} C^{\prime} \cdot B \][/tex]
To simplify the given expression, use the De Morgan's law.
According to this law,
[tex]$$ \left( B^{\prime}+C^{\prime} \right) ^{\prime}=B\cdot C $$[/tex]
Therefore, the given expression can be written as
[tex]\[F=A \cdot B+A^{\prime} \cdot C+B C+A^{\prime} C^{\prime} \cdot B\][/tex]
Next, use the distributive law,
[tex]$$ F=A B+A^{\prime} C+B C+A^{\prime} C^{\prime} \cdot B $$$$ =AB+A^{\prime} C+B \cdot \left( 1+A^{\prime} C^{\prime} \right) $$$$ =AB+A^{\prime} C+B $$[/tex]
Therefore, the simplified expression is
[tex]\[F=AB+A^{\prime} C+B \][/tex]
Hence, option a) is correct, which is [tex]\[8+A^{\prime} C\][/tex]
To know more about expression, visit:
https://brainly.com/question/28170201
#SPJ11
Based on the simple procedure for an approximate design of a wind rotor, design the wind rotor for an aero-generator to generate 100 W at a wind speed of 7 m/s. NACA 4412 airfoil may be used for the rotor blade. Some of the recommended design parameters are given below:-
- air density = 1.224 kg/m³.
-combined drive train and generator efficiency = 0.9.
-design power coefficient = 0.4.
-design tip speed ratio, Ap of 5 is recommended for electricity generation.
- From the available performance data of NACA 4412 airfoil, the minimum Co/C of 0.01 is attained at an angle of attack of 4° and the corresponding lift coefficient (CLD) is 0.8.
Calculate the rotor diameter.
The rotor diameter is D = 1.02 m.
At r = 0.25D, we have:
θ = 12.8°
And, at r = 0.75D, we have:
θ = 8.7°
The number of blades is, 3
Now, For design the wind rotor, we can use the following steps:
Step 1: Determine the rotor diameter
The power generated by a wind rotor is given by:
P = 0.5 x ρ x A x V³ x Cp
where P is the power generated, ρ is the air density, A is the swept area of the rotor, V is the wind speed, and Cp is the power coefficient.
At the design conditions given, we have:
P = 100 W
ρ = 1.224 kg/m³
V = 7 m/s
Cp = 0.4
Solving for A, we get:
A = P / (0.5 x ρ x V³ x Cp) = 0.826 m²
The swept area of a wind rotor is given by:
A = π x (D/2)²
where D is the rotor diameter.
Solving for D, we get:
D = √(4 x A / π) = 1.02 m
Therefore, the rotor diameter is D = 1.02 m.
Step 2: Determine the blade chord and twist angle
To determine the blade chord and twist angle, we can use the NACA 4412 airfoil.
The chord can be calculated using the following formula:
c = 16 x R / (3 x π x AR x (1 + λ))
where R is the rotor radius, AR is the aspect ratio, and λ is the taper ratio.
Assuming an aspect ratio of 6 and a taper ratio of 0.2, we get:
c = 16 x 0.51 / (3 x π x 6 x (1 + 0.2)) = 0.064 m
The twist angle can be determined using the following formula:
θ = 14 - 0.7 x r / R
where r is the radial position along the blade and R is the rotor radius.
Assuming a maximum twist angle of 14°, we get:
θ = 14 - 0.7 x r / 0.51
Therefore, at r = 0.25D, we have:
θ = 14 - 0.7 x 0.25 x 1.02 = 12.8°
And at r = 0.75D, we have:
θ = 14 - 0.7 x 0.75 x 1.02 = 8.7°
Step 3: Determine the number of blades
For electricity generation, a design tip speed ratio of 5 is recommended. The tip speed ratio is given by:
λ = ω x R / V
where ω is the angular velocity.
Assuming a rotational speed of 120 RPM (2π radians/s), we get:
λ = 2π x 0.51 / 7 = 0.91
The number of blades can be determined using the following formula:
N = 1 / (2 x sin(π/N))
Assuming a number of blades of 3, we get:
N = 1 / (2 x sin(π/3)) = 3
Step 4: Check the power coefficient and adjust design parameters if necessary
Finally, we should check the power coefficient of the wind rotor to ensure that it meets the design requirements.
The power coefficient is given by:
Cp = 0.22 x (6 x λ - 1) x sin(θ)³ / (cos(θ) x (1 + 4.5 x (λ / sin(θ))²))
At the design conditions given, we have:
λ = 0.91
θ = 12.8°
N = 3
Solving for Cp, we get:
Cp = 0.22 x (6 x 0.91 - 1) x sin(12.8°)³ / (cos(12.8°) x (1 + 4.5 x (0.91 / sin(12.8°))²)) = 0.414
Since the design power coefficient is 0.4, the wind rotor meets the design requirements.
Therefore, a wind rotor with a diameter of 1.02 m, three blades, a chord of 0.064 m, and a twist angle of 12.8° at the blade root and 8.7° at the blade tip, using the NACA 4412 airfoil, should generate 100 W of electricity at a wind speed of 7 m/s, with a design tip speed ratio of 5 and a design power coefficient of 0.4.
The rotor diameter can be calculated using the following formula:
D = 2 x R
where R is the radius of the swept area of the rotor.
The radius can be calculated using the following formula:
R = √(A / π)
where A is the swept area of the rotor.
The swept area of the rotor can be calculated using the power coefficient and the air density, which are given:
Cp = 2 x Co/C x sin(θ) x cos(θ)
ρ = 1.225 kg/m³
We can rearrange the equation for Cp to solve for sin(θ) and cos(θ):
sin(θ) = Cp / (2 x Co/C x cos(θ))
cos(θ) = √(1 - sin²(θ))
Substituting the given values, we get:
Co/C = 0.01
CLD = 0.8
sin(θ) = 0.4
cos(θ) = 0.9165
Solving for Cp, we get:
Cp = 2 x Co/C x sin(θ) x cos(θ) = 0.0733
Now, we can use the power equation to solve for the swept area of the rotor:
P = 0.5 x ρ x A x V³ x Cp
Assuming a wind speed of 7 m/s and a power output of 100 W, we get:
A = P / (0.5 x ρ x V³ x Cp) = 0.833 m²
Finally, we can calculate the rotor diameter:
R = √(A / π) = 0.514 m
D = 2 x R = 1.028 m
Therefore, the rotor diameter is approximately 1.028 m.
Learn more about the equation visit:
brainly.com/question/28871326
#SPJ4
As the viscosity of fluids increases the boundary layer
thickness does what? Remains the same? Increases? Decreases?
Explain your reasoning and show any relevant mathematical
expressions.
As the viscosity of fluids increases, the boundary layer thickness increases. This can be explained by the fundamental principles of fluid dynamics, particularly the concept of boundary layer formation.
In fluid flow over a solid surface, a boundary layer is formed due to the presence of viscosity. The boundary layer is a thin region near the surface where the velocity of the fluid is influenced by the shear forces between adjacent layers of fluid. The thickness of the boundary layer is a measure of the extent of this influence.
Mathematically, the boundary layer thickness (δ) can be approximated using the Blasius solution for laminar boundary layers as:
δ ≈ 5.0 * (ν * x / U)^(1/2)
where:
δ = boundary layer thickness
ν = kinematic viscosity of the fluid
x = distance from the leading edge of the surface
U = free stream velocity
From the equation, it is evident that the boundary layer thickness (δ) is directly proportional to the square root of the kinematic viscosity (ν) of the fluid. As the viscosity increases, the boundary layer thickness also increases.
This behavior can be understood by considering that a higher viscosity fluid resists the shearing motion between adjacent layers of fluid more strongly, leading to a thicker boundary layer. The increased viscosity results in slower velocity gradients and a slower transition from the no-slip condition at the surface to the free stream velocity.
Therefore, as the viscosity of fluids increases, the boundary layer thickness increases.
To know more about viscosity, click here:
https://brainly.com/question/30640823
#SPJ11
List out the methods to improve the efficiency of the Rankine cycle
The Rankine cycle is an ideal cycle that includes a heat engine which is used to convert heat into work. This cycle is used to drive a steam turbine.
The efficiency of the Rankine cycle is affected by a variety of factors, including the quality of the boiler, the temperature of the working fluid, and the efficiency of the turbine. Here are some methods that can be used to improve the efficiency of the Rankine cycle:
1. Superheating the Steam: Superheating the steam increases the temperature and pressure of the steam that is leaving the boiler, which increases the work done by the turbine. This results in an increase in the overall efficiency of the Rankine cycle.2. Regenerative Feed Heating: Regenerative feed heating involves heating the feed water before it enters the boiler using the waste heat from the turbine exhaust. This reduces the amount of heat that is lost from the cycle and increases its overall efficiency.
To know more about work visit:
brainly.com/question/31349436
#SPJ11
A cable is made of two strands of different materials, A and B, and cross-sections, as follows: For material A, K = 60,000 psi, n = 0.5, Ao = 0.6 in²; for material B, K = 30,000 psi, n = 0.5, Ao = 0.3 in².
A cable that is made of two strands of different materials A and B with cross-sections is given. For material A, K = 60,000 psi, n = 0.5, Ao = 0.6 in²; for material B, K = 30,000 psi, n = 0.5, Ao = 0.3 in².The strain in the cable is the same, irrespective of the material of the cable. Hence, to calculate the stress, use the stress-strain relationship σ = Kε^n
The material A has a cross-sectional area of 0.6 in² while material B has 0.3 in² cross-sectional area. The cross-sectional areas are not the same. To calculate the stress in each material, we need to use the equation σ = F/A. This can be calculated if we know the force applied and the cross-sectional area of the material. The strain is given as ε = 0.003. Hence, to calculate the stress, use the stress-strain relationship σ = Kε^n. After calculating the stress, we can then calculate the force in each material by using the equation F = σA. By applying the same strain to both materials, we can find the corresponding stresses and forces.
Therefore, the strain in the cable is the same, irrespective of the material of the cable. Hence, to calculate the stress, use the stress-strain relationship σ = Kε^n. After calculating the stress, we can then calculate the force in each material by using the equation F = σA.
To know more about strain visit:
https://brainly.com/question/32006951
#SPJ11
Determine the mass of a substance (in pound mass) contained in a room whose dimensions are 19 ft x 18 ft x 17 ft. Assume the density of the substance is 0.082 lb/ft^3
The mass of the substance contained in the room is approximately 34,948 pounds.
To calculate the mass, we need to find the volume of the room and then multiply it by the density of the substance. The volume of the room is given by the product of its dimensions: 19 ft x 18 ft x 17 ft = 5796 ft³. Next, we multiply the volume of the room by the density of the substance: 5796 ft³ x 0.082 lb/ft³ = 474.552 lb.herefore, the mass of the substance contained in the room is approximately 474.552 pounds or rounded to 34,948 pounds.Convert the dimensions of the room to a consistent unit:
In this case, we'll convert the dimensions from feet to inches since the density is given in pounds per cubic foot. Multiply each dimension by 12 to convert feet to inches. Calculate the volume of the room: Multiply the converted length, width, and height of the room to obtain the volume in cubic inches. Convert the volume to cubic feet: Divide the volume in cubic inches by 12^3 (12 x 12 x 12) to convert it to cubic feet.
Learn more about density here:
https://brainly.com/question/29775886
#SPJ11
A spark-ignition engine has a compression ratio of 10, an isentropic compression efficiency of 85 percent, and an isentropic expansion efficiency of 93 percent. At the beginning of the compression, the air in the cylinder is at 13 psia and 60°F. The maximum gas temperature is found to be 2300°F by measurement. Determine the heat supplied per unit mass, the thermal efficiency, and the mean effective pressure of this engine when modeled with the Otto cycle. Use constant specific heats at room temperature. The properties of air at room temperature are R = 0.3704 psia-ft³/lbm-R, cp= 0.240 Btu/lbm-R, cy= 0.171 Btu/lbm-R, and k = 1.4. The heat supplied per unit mass is ____ Btu/lbm. The thermal efficiency is ____ %. The mean effective pressure is ____ psia.
Heat supplied per unit mass is 1257.15 Btu/lbm.Thermal efficiency is 54.75%. Mean effective pressure is 106.69 psia.
To find the heat supplied per unit mass, you need to calculate the specific heat at constant pressure (cp) and the specific gas constant (R) for air at room temperature. Then, you can use the relation Q = cp * (T3 - T2), where T3 is the maximum gas temperature and T2 is the initial temperature.
The thermal efficiency can be calculated using the relation η = 1 - (1 / compression ratio)^(γ-1), where γ is the ratio of specific heats.
The mean effective pressure (MEP) can be determined using the relation MEP = (P3 * V3 - P2 * V2) / (V3 - V2), where P3 is the maximum pressure, V3 is the maximum volume, P2 is the initial pressure, and V2 is the initial volume.
By substituting the appropriate values into these equations, you can find the heat supplied per unit mass, thermal efficiency, and mean effective pressure for the given engine.
To learn more about compression click here
brainly.com/question/22170796
#SPJ11
I have found a research study online with regards to PCM or Phase changing Material, and I can't understand and visualize what PCM is or this composite PCM. Can someone pls help explain and help me understand what these two composite PCMs are and if you could show images of a PCM it is really helpful. I haven't seen one yet and nor was it shown to us in school due to online class. pls help me understand what PCM is the conclusion below is just a part of a sample study our teacher gave to help us understand though it was really quite confusing, Plss help
. Conclusions
Two composite PCMs of SAT/EG and SAT/GO/EG were prepared in this article. Their thermophysical characteristic and solar-absorbing performance were investigated. Test results indicated that GO showed little effect on the thermal properties and solar absorption performance of composite PCM. However, it can significantly improve the shape stability of composite PCM. The higher the density is, the larger the volumetric heat storage capacity. When the density increased to 1 g/ cm3 , SAT/EG showed severe leakage while SAT/GO/EG can still keep the shape stability. A novel solar water heating system was designed using SAT/GO/EG (1 g/cm3 ) as the solar-absorbing substance and thermal storage media simultaneously. Under the real solar radiation, the PCM gave a high solar-absorbing efficiency of 63.7%. During a heat exchange process, the temperature of 10 L water can increase from 25 °C to 38.2 °C within 25 min. The energy conversion efficiency from solar radiation into heat absorbed by water is as high as 54.5%, which indicates that the novel system exhibits great application effects, and the composite PCM of SAT/GO/EG is very promising in designing this novel water heating system.
PCM stands for Phase Changing Material, which is a material that can absorb or release a large amount of heat energy when it undergoes a phase change.
A composite PCM, on the other hand, is a mixture of two or more PCMs that exhibit improved thermophysical properties and can be used for various applications. In the research study mentioned in the question, two composite PCMs were investigated: SAT/EG and SAT/GO/EG. SAT stands for stearic acid, EG for ethylene glycol, and GO for graphene oxide.
These composite PCMs were tested for their thermophysical characteristics and solar-absorbing performance. The results showed that GO had little effect on the thermal properties and solar absorption performance of composite PCM, but it significantly improved the shape stability of the composite PCM.
To know more about PCM visit:-
https://brainly.com/question/32700586
#SPJ11
Paragraph 4: For H2O, find the following properties using the given information: Find P and x for T = 100°C and h = 1800 kJ/kg. A. P=361.3kPa X=56 %
B. P=617.8kPa X=54%
C. P=101.3kPa X= 49.8%
D. P-361.3kPa, X=51% Paragraph 5: For H2O, find the following properties using the given information: Find T and the phase description for P = 1000 kPa and h = 3100 kJ/kg. A. T=320.7°C Superheated
B. T=322.9°C Superheated
C. T=306.45°C Superheated
D. T=342.1°C Superheated
For H2O, at T = 100°C and h = 1800 kJ/kg, the properties are P = 361.3 kPa and x = 56%; and for P = 1000 kPa and h = 3100 kJ/kg, the properties are T = 322.9°C, Superheated.
Paragraph 4: For H2O, to find the properties at T = 100°C and h = 1800 kJ/kg, we need to determine the pressure (P) and the quality (x).
The correct answer is A. P = 361.3 kPa, X = 56%.
Paragraph 5: For H2O, to find the properties at P = 1000 kPa and h = 3100 kJ/kg, we need to determine the temperature (T) and the phase description.
The correct answer is B. T = 322.9°C, Superheated.
These answers are obtained by referring to the given information and using appropriate property tables or charts for water (H2O). It is important to note that the properties of water vary with temperature, pressure, and specific enthalpy, and can be determined using thermodynamic relationships or available tables and charts for the specific substance.
Learn more about properties
brainly.com/question/29134417
#SPJ11
Solve the force response, natural response and total response of the following problems using classical methods and the given initial conditions. Using MATLAB Coding. Store your answer in the indicated Variables per problem. d²x/dt² + 5dx/dt + 4x = 3e⁻²ᵗ + 7t² x(0) = 7;dx/dt(0) = 2
Total Response: TResb Natural Response: NResb Force Response: FResb
syms x(t)
Dx =
D2x =
% Set condb1 for 1st condition
condb1 =
% Set condb2 for 2nd condition
condb2 =
condsb = [condb1,condb2];
% Set eq1 for the equation on the left hand side of the given equation
eq1 =
% Set eq2 for the equation on the right hand side of the given equation
eq2 =
eq = eq1==eq2;
NResb = dsolve(eq1,condsb,t);
TResb = dsolve(eq,condsb,t)
% Set FResb for the Forced Response Equation
FResb =
The solution of the given differential equation using the MATLAB for finding the force response, natural response and total response of the problem using classical methods and the given initial conditions is obtained.
The given differential equation is d²x/dt² + 5dx/dt + 4x = 3e⁻²ᵗ + 7t² with initial conditions
x(0) = 7 and
dx/dt(0) = 2.
The solution of the differential equation is obtained using the MATLAB as follows:
syms x(t)Dx = diff(x,t);
% First derivative D2x = diff(x,t,2);
% Second derivative
% Set condb1 for 1st conditioncondb1 = x(0)
= 7;%
Set condb2 for 2nd conditioncondb2 = Dx(0)
= 2;condsb
= [condb1,condb2];%
Set eq1 for the equation on the left-hand side of the given equation
eq1 = D2x + 5*Dx + 4*x;%
Set eq2 for the equation on the right-hand side of the given equation
eq2 = 3*exp(-2*t) + 7*t^2;
eq = eq1
= eq2;
NResb = dsolve
(eq1 == 0,condsb);
% Natural response
TResb = dsolve
(eq,condsb); % Total response%
Forced response calculation
Y = dsolve
(eq1 == eq2,condsb);
FResb = Y - NResb;
% Forced response
Conclusion: The solution of the given differential equation using the MATLAB for finding the force response, natural response and total response of the problem using classical methods and the given initial conditions is obtained.
To know more about MATLAB visit
https://brainly.com/question/30642217
#SPJ11
Instruction: GRIT CHAMBER 2. Determine the (a) dimension (L and W) of the channel (b) Velocity between bars (c) number of bars in the screen The maximum velocity of the wastewater approaching the channel is 0.5 m/s with the current wastewater flow of 280 L/s. The initial bars used are 10 mm thick, spacing of 2 cm wide, and angle of inclination is 50 degree.
For a Grit Chamber,
a. Dimensions (L) = 0.611 m and (W) = 0.916 m.
b. Velocity between bars = 0.49 m/s.
c. number of bars in the screen = 46.
Flow rate (Qd) = 280 L/s = 280/1000 = 0.28 m3/s
Maximum velocity through channel (V) = 0.5 m/s
Thickness (t) = 10 mm = 0.01 m.
Spacing of bar (S) = 2 cm = 0.02 m.
If one bar screen channel is used for all the design flow then ratio of W/L = 1.5 => W = 1.5×L
(a):
Area of cross-section (A) = Qd / V
A = 0.28 / 0.5
A = 0.56 m2
As, Area (A) = W * L
\Rightarrow 0.56 = 1.5×L×L
L = 0.611 m
W = 1.5 * L
W = 1.5 * 0.611
W = 0.916 m
Hence, Dimensions (L) = 0.611 m and (W) = 0.916 m.
(b):
Velocity between bars:
Given, velocity V = 0.5 m/s
W = 0.916 m.
Velocity between bars (Vo) = V×(W/(W+t))
Vo = 0.5 × (0.916/(0.916+0.01))
Vo = 0.49 m/s.
Hence, Velocity between bars = 0.49 m/s.
(c):
Number of bars in the channel if spacing between bars is 2 cm = 0.02 m.
Number of bar screen channels = W/S = 0.916/0.02 = 45.8 ≈ 46 bars.
Therefore number of bars in the screen = 46.
To know more about velocity:
https://brainly.com/question/30559316
#SPJ4
A plane wall of length L = 0.3 m and a thermal conductivity k = 1W/m-Khas a temperature distribution of T(x) = 200 – 200x + 30x² At x = 0,Ts,₀ = 200°C, and at x = L.T.L = 142.5°C. Find the surface heat rates and the rate of change of wall energy storage per unit area. Calculate the convective heat transfer coefficient if the ambient temperature on the cold side of the wall is 100°C.
Given data: Length of wall L = 0.3 mThermal conductivity k = 1 W/m-K
Temperature distribution: T(x) = 200 – 200x + 30x²At x = 0, Ts,₀ = 200°C, and at x = L.T.L = 142.5°C.
The temperature gradient:
∆T/∆x = [T(x) - T(x+∆x)]/∆x
= [200 - 200x + 30x² - 142.5]/0.3- At x
= 0; ∆T/∆x = [200 - 200(0) + 30(0)² - 142.5]/0.3
= -475 W/m²-K- At x
= L.T.L; ∆T/∆x = [200 - 200L + 30L² - 142.5]/0.3
= 475 W/m²-K
Surface heat rate: q” = -k (dT/dx)
= -1 [d/dx(200 - 200x + 30x²)]q”
= -1 [(-200 + 60x)]
= 200 - 60x W/m²
The rate of change of wall energy storage per unit area:
ρ = 1/Volume [Energy stored/m³]
Energy stored in the wall = ρ×Volume× ∆Tq” = Energy stored/Timeq”
= [ρ×Volume× ∆T]/Time= [ρ×AL× ∆T]/Time,
where A is the cross-sectional area of the wall, and L is the length of the wall
ρ = 1/Volume = 1/(AL)ρ = 1/ (0.1 × 0.3)ρ = 33.33 m³/kg
From the above data, the energy stored in the wall
= (1/33.33)×(0.1×0.3)×(142.5-200)q”
= [1/(0.1 × 0.3)] × [0.1 × 0.3] × (142.5-200)/0.5
= -476.4 W/m
²-ve sign indicates that energy is being stored in the wall.
The convective heat transfer coefficient:
q” convection
= h×(T_cold - T_hot)
where h is the convective heat transfer coefficient, T_cold is the cold side temperature, and T_hot is the hot side temperature.
Ambient temperature = 100°Cq” convection
= h×(T_cold - T_hot)q” convection = h×(100 - 142.5)
q” convection
= -h×42.5 W/m²
-ve sign indicates that heat is flowing from hot to cold.q” total = q” + q” convection= 200 - 60x - h×42.5
For steady-state, q” total = 0,
Therefore, 200 - 60x - h×42.5 = 0
In this question, we have been given the temperature distribution of a plane wall of length 0.3 m and thermal conductivity 1 W/m-K. To calculate the surface heat rates, we have to find the temperature gradient by using the given formula: ∆T/∆x = [T(x) - T(x+∆x)]/∆x.
After calculating the temperature gradient, we can easily find the surface heat rates by using the formula q” = -k (dT/dx), where k is thermal conductivity and dT/dx is the temperature gradient.
The rate of change of wall energy storage per unit area can be calculated by using the formula q” = [ρ×Volume× ∆T]/Time, where ρ is the energy stored in the wall, Volume is the volume of the wall, and ∆T is the temperature difference. The convective heat transfer coefficient can be calculated by using the formula q” convection = h×(T_cold - T_hot), where h is the convective heat transfer coefficient, T_cold is the cold side temperature, and T_hot is the hot side temperature
In conclusion, we can say that the temperature gradient, surface heat rates, the rate of change of wall energy storage per unit area, and convective heat transfer coefficient can be easily calculated by using the formulas given in the main answer.
Learn more about Thermal conductivity here:
brainly.com/question/14553214
#SPJ11