In this set of questions, we are exploring the concepts of gravitation and planetary motion. We use the formulas related to gravitational force, orbital speed, and orbital radius to solve various problems.
Firstly, we calculate the gravitational force between two whales and compare it to the gravitational force between each whale and the Earth. Then, we determine the gravitational force on an asteroid and a planet, as well as the orbital speed and time taken for an asteroid to complete one orbit.
Next, we find the orbital radius and angular momentum of a comet orbiting a star, and also calculate the speed of the comet at its farthest position. Finally, we discuss the period of a geosynchronous satellite orbiting the Earth and how satellites can be used to determine the mass of unknown planets.
a. To calculate the gravitational force between the whale shark and the blue whale, we use the formula F = GMm/r^2, where G is the gravitational constant, M and m are the masses of the two objects, and r is the distance between them. Plugging in the values, we find the gravitational force between them.
b. To compare the gravitational force between the two animals and the Earth, we calculate the gravitational force between each animal and the Earth using the same formula.
We observe that the force between the animals is much smaller compared to the force between each animal and the Earth. This is because the mass of the Earth is significantly larger than the mass of the animals, resulting in a stronger gravitational force.
c. Objects on Earth do not seem to be attracted to each other strongly because the gravitational force between them is much weaker compared to the gravitational force between each object and the Earth.
The mass of the Earth is substantially larger than the mass of individual objects on its surface, causing the gravitational force exerted by the Earth to dominate and make the gravitational force between objects on Earth negligible in comparison.
Learn more about satellite click here:
brainly.com/question/28766254
#SPJ11
A scuba diver is swimming 17. 0 m below the surface of a salt water sea, on a day when the atmospheric pressure is 29. 92 in HG. What is the gauge pressure, on the diver the situation? The salt water has a density of 1.03 g/cm³. Give your answer in atmospheres.
The gauge pressure on a scuba diver swimming at a depth of 17.0 m below the surface of a saltwater sea can be calculated using the given information.
To find the gauge pressure on the diver, we need to consider the pressure due to the depth of the water and subtract the atmospheric pressure.
Pressure due to depth: The pressure at a given depth in a fluid is given by the equation P = ρgh, where P is the pressure, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the depth.
In this case, the depth is 17.0 m, and the density of saltwater is 1.03 g/cm³.
Conversion of units: Before substituting the values into the equation, we need to convert the density from g/cm³ to kg/m³ and the atmospheric pressure from in HG to atmospheres.
Density conversion: 1.03 g/cm³ = 1030 kg/m³Atmospheric pressure conversion: 1 in HG = 0.0334211 atmospheres (approx.)
Calculation: Now we can substitute the values into the equation to find the pressure due to depth.P = (1030 kg/m³) * (9.8 m/s²) * (17.0 m) = 177470.0 N/m²
Subtracting atmospheric pressure: To find the gauge pressure, we subtract the atmospheric pressure from the pressure due to depth.
Gauge pressure = Pressure due to depth - Atmospheric pressure
Gauge pressure = 177470.0 N/m² - (29.92 in HG * 0.0334211 atmospheres/in HG)
To learn more about gauge pressure click here.
brainly.com/question/30698101
#SPJ11
A straight wire with length 2320cm carries a current 20A which is directed to the right and is perpendicular to an unknown uniform magnetic field B. A magnetic
force 31pN acts on a conductor which is directed downwards. A. Determine the magnitude and the direction of the magnetic field in the region
through which the current passes. B. If the angle between the current and the magnetic field is 54 this time, what would
be the new value of the magnitude of the new magnetic force?
a. The magnitude of the magnetic field is [tex]2.84 * 10^(^-^1^1^) Tesla.[/tex]
b. The new value of the magnitude of the magnetic force is [tex]4.49 * 10^(^-^1^1^)[/tex] Newtons.
How do we calculate?a.
F_ = BILsinθ
F_ = magnetic force,
B = magnetic field
I = current,
L = length of the wire,
θ = angle between the current and the magnetic field.
Current (I) = 20 A
Length of wire (L) = 2320 cm = 23.20 m
Magnetic force (F) = 31 pN = 31 x 10^(-12) N
B = F/ (ILsinθ)
B = ([tex]31 * 10^(^-^1^2)[/tex]) N) / (20 A x 23.20 m x sin(90°))
B = [tex]2.84 * 10^(^-^1^1^)[/tex] T
b.
F' = BILsinθ'
F' = ([tex]2.84 * 10^(^-^1^1^)[/tex]T) x (20 A) x (23.20 m) x sin(54°)
F' = 4.49 x 10^(-11) N
Learn more about magnetic field at:
https://brainly.com/question/14411049
#SPJ4
Imagine you had a device to use for this experiment. The device would shoot a series of 2. 0 g balls along the surface at the box, each with a velocity of 30 cm/s [E60N]. In 2. 0 s it shoots 10 successive 2. 0 balls, all of which collide and rebound off the 100g box, as with the first ball. What would be the total impulse delivered to the box by the 10 collisions?What would be the total change in momentum of the 100g box?What would be the total change in velocity of the 100g box after these 10 collisions?
The total impulse delivered to the box by the 10 collisions is 0.006 kg·m/s, the total change in momentum of the 100 g box is 0.012 kg·m/s, and the total change in velocity of the 100 g box after these 10 collisions is 0.12 m/s.
The total impulse delivered to the box by the 10 collisions can be calculated using the equation:
Impulse = Change in Momentum
First, let's calculate the momentum of each 2.0 g ball. The momentum of an object is given by the equation:
Momentum = mass x velocity
Since the mass of each ball is 2.0 g and the velocity is 30 cm/s, we convert the mass to kg and the velocity to m/s:
mass = 2.0 g = 0.002 kg
velocity = 30 cm/s = 0.3 m/s
Now, we can calculate the momentum of each ball:
Momentum = 0.002 kg x 0.3 m/s = 0.0006 kg·m/s
Since 10 balls are shot in succession, the total impulse delivered to the box is the sum of the impulses from each ball. Therefore, we multiply the momentum of each ball by the number of balls (10) to find the total impulse:
Total Impulse = 0.0006 kg·m/s x 10 = 0.006 kg·m/s
Next, let's calculate the total change in momentum of the 100 g box. The initial momentum of the box is zero since it is at rest. After each collision, the box gains momentum in the opposite direction to the ball's momentum. Since the box rebounds off the ball with the same momentum, the change in momentum for each collision is twice the momentum of the ball. Therefore, the total change in momentum of the box is:
Total Change in Momentum = 2 x Total Impulse = 2 x 0.006 kg·m/s = 0.012 kg·m/s
Finally, let's calculate the total change in velocity of the 100 g box after these 10 collisions. The change in velocity can be found using the equation:
Change in Velocity = Change in Momentum / Mass
The mass of the box is 100 g = 0.1 kg. Therefore, the total change in velocity is:
Total Change in Velocity = Total Change in Momentum / Mass = 0.012 kg·m/s / 0.1 kg = 0.12 m/s
Therefore, the total impulse delivered to the box by the 10 collisions is 0.006 kg·m/s, the total change in momentum of the 100 g box is 0.012 kg·m/s, and the total change in velocity of the 100 g box after these 10 collisions is 0.12 m/s.
To more about velocity visit:
https://brainly.com/question/34025828
#SPJ11
A horizontal wire of length 3.0 m carries a current of 6.0 A and is oriented so that the current direction is 50 ∘ S of W. The Earth's magnetic field is due north at this point and has a strength of 0.14×10 ^−4 T. What are the magnitude and direction of the force on the wire? 1.9×10 N ^−4 , out of the Earth's surface None of the choices is correct. 1.6×10 N ^−4 , out of the Earth's surface 1.9×10 N ^−4 , toward the Earth's surface 1.6×10 N ^−4 , toward the Earth's surface
The magnitude of the force on the wire is 1.9 × 10⁻⁴ N. The direction of the current is 50° south of the west. 1.9×10 N⁻⁴, out of the Earth's surface is the correct option.
Length of the horizontal wire, L = 3.0 m
Current flowing through the wire, I = 6.0 A
Earth's magnetic field, B = 0.14 × 10⁻⁴ T
Angle made by the current direction with due west = 50° south of westForce on a current-carrying wire due to the Earth's magnetic field is given by the formula:
F = BILsinθ, where
L is the length of the wire, I is the current flowing through it, B is the magnetic field strength at that location and θ is the angle between the current direction and the magnetic field direction
Magnitude of the force on the wire is
F = BILsinθF = (0.14 × 10⁻⁴ T) × (6.0 A) × (3.0 m) × sin 50°F = 1.9 × 10⁻⁴ N
Earth's magnetic field is due north, the direction of the force on the wire is out of the Earth's surface. Therefore, the correct option is 1.9×10 N⁻⁴, out of the Earth's surface.
You can learn more about magnitude at: brainly.com/question/31022175
#SPJ11
Part A What percentage of all the molecules in the glass are water? Express your answer using six significant figures. D | ΑΣΦ VO ? MAREH nwater Submit Request Answer % Assume the total number of molecules in a glass of liquid is about 1,000,000 million trillion. One million trillion of these are molecules of some poison, while 999,999 million trillion of these are water molecules.
Assuming the total number of molecules in a glass of liquid is about 1,000,000 million trillion.
One million trillion of these are molecules of some poison, while 999,999 million trillion of these are water molecules.
Express your answer using six significant figures. To determine the percentage of all the molecules in the glass that are water, we need to use the following formula: % of water = (number of water molecules/total number of molecules) × 100.
To know more about liquid visit:
https://brainly.com/question/20922015
#SPJ11
Transcribed image text: Question 8 (1 point) A proton is placed at rest some distance from a second charged object. A that point the proton experiences a potential of 45 V. Which of the following statements are true? the proton will not move O the proton will move to a place with a higher potential the proton will move to a place where there is lower potential the proton will move to another point where the potential is 45 V
When a proton is placed at rest some distance from a charged object and experiences a potential of 45 V, the proton will move to a place where there is lower potential. The correct answer is option c.
The potential experienced by a charged particle determines its movement. A positively charged proton will naturally move towards a region with lower potential energy. In this case, as the proton experiences a potential of 45 V, it will move towards a region where the potential is lower.
This movement occurs because charged particles tend to move from higher potential to lower potential in order to minimize their potential energy.
Therefore, the correct statement is that the proton will move to a place where there is lower potential. Option c is correct.
To know more about proton, click here-
brainly.com/question/12535409
#SPJ11
50. The angle that a reflected light ray makes with the surface normal A) is smaller B) the same size C) greater than the angle that the incident ray makes with the normal 51. The speed of light in gl
The angle that a reflected light ray makes with the surface normal is smaller.
The law of reflection states that the angle of incidence is equal to the angle of reflection. When light is reflected from a surface, the angle at which it is reflected (angle of reflection) is equal to the angle at which it hits the surface (angle of incidence). The angle that a reflected light ray makes with the surface normal is the angle of reflection. Therefore, the answer is that the angle that a reflected light ray makes with the surface normal is smaller than the angle that the incident ray makes with the normal.
The speed of light in glass is less than the speed of light in a vacuum. This means that the refractive index of glass is greater than 1. When light passes through a medium with a higher refractive index than the medium it was previously in, the light is bent towards the normal. Therefore, the answer is that the speed of light in glass is less than the speed of light in a vacuum, and the refractive index of glass is greater than 1.
The angle that a reflected light ray makes with the surface normal is A) is smaller. The law of reflection states that the angle of incidence is equal to the angle of reflection. When light is reflected from a surface, the angle at which it is reflected (angle of reflection) is equal to the angle at which it hits the surface (angle of incidence). The angle that a reflected light ray makes with the surface normal is the angle of reflection. Therefore, the answer is that the angle that a reflected light ray makes with the surface normal is smaller than the angle that the incident ray makes with the normal.
The speed of light in glass is less than the speed of light in a vacuum. This means that the refractive index of glass is greater than 1. When light passes through a medium with a higher refractive index than the medium it was previously in, the light is bent towards the normal. Therefore, the answer is that the speed of light in glass is less than the speed of light in vacuum, and the refractive index of glass is greater than 1.
When a light wave strikes a surface, it can be either absorbed or reflected. Reflection occurs when light bounces back from a surface. The angle at which the light strikes the surface is known as the angle of incidence, and the angle at which it reflects is known as the angle of reflection. The angle of incidence is always equal to the angle of reflection, as stated by the law of reflection. The angle that a reflected light ray makes with the surface normal is the angle of reflection. It's smaller than the angle of incidence.
When light travels through different mediums, such as air and glass, its speed changes, and it bends. Refraction is the process of bending that occurs when light moves from one medium to another with a different density. The refractive index is a measure of the extent to which a medium slows down light compared to its speed in a vacuum. The refractive index of a vacuum is 1.
When light moves from a medium with a low refractive index to a medium with a high refractive index, it bends toward the normal, which is a line perpendicular to the surface separating the two media.
When light is reflected from a surface, the angle of reflection is always equal to the angle of incidence. The angle of reflection is the angle that a reflected light ray makes with the surface normal, and it is smaller than the angle of incidence. The refractive index of a medium is a measure of how much the medium slows down light compared to its speed in a vacuum. When light moves from a medium with a low refractive index to a medium with a high refractive index, it bends toward the normal.
To know more about refractive index visit
brainly.com/question/30761100
#SPJ11
A rod of negligible resistance is sliding along a pair of long tracks--also of negligible resistance. The tracks are connected on one end by a wire of resistance R, the rod is sliding away from this end at constant speed, and there is a uniform magnetic field which points in a direction perpendicular to the plane containing the rod and the tracks. Initially, the area bounded by the rod, the tracks, and the end is A1, but after some time the area is A2 = 3A1. At this initial time, the induced emf was 3.0 V. What will it be at the latter time, when the total enclosed area has tripled?
The induced emf will be 9.0 V when the total enclosed area has tripled.
According to Faraday's law of electromagnetic induction, the induced emf (ε) in a circuit is proportional to the rate of change of magnetic flux through the circuit. The magnetic flux (Φ) is given by the product of the magnetic field (B) and the area (A) enclosed by the circuit.
In this scenario, the initially induced emf (ε1) is 3.0 V, and the initial area (A1) is known. When the total enclosed area becomes A2 = 3A1, it means the area has tripled. Since the speed of the rod is constant, the rate of change of area is also constant.
Therefore, the ratio of the final area (A2) to the initial area (A1) is equal to the ratio of the final induced emf (ε2) to the initial induced emf (ε1).
Mathematically, we can express this relationship as:
A2/A1 = ε2/ε1
Substituting the known values, A2 = 3A1 and ε1 = 3.0 V, we can solve for ε2:
3A1/A1 = ε2/3.0 V
3 = ε2/3.0 V
Cross-multiplying, we find:
ε2 = 9.0 V
Hence, the induced emf will be 9.0 V when the total enclosed area has tripled.
To learn more about magnetic flux
Click here brainly.com/question/1596988
#SPJ11
Determine the electrical resistance of a 20.0 m length of tungsten wire of radius 0.200 mm. The resistivity of tungsten is 5.6×10^ −8 Ω⋅m.
The electrical resistance of a 20.0 m length of tungsten wire of radius 0.200 mm, when the resistivity of tungsten is 5.6×10^-8 Ω⋅m can be determined using the following steps:
1: Find the cross-sectional area of the wire The cross-sectional area of the wire can be calculated using the formula for the area of a circle, which is given by: A
= πr^2where r is the radius of the wire. Substituting the given values: A
= π(0.0002 m)^2A
= 1.2566 × 10^-8 m^2given by: R
= ρL/A Substituting
= (5.6 × 10^-8 Ω⋅m) × (20.0 m) / (1.2566 × 10^-8 m^2)R
= 1.77 Ω
To know more about resistivity visit:
https://brainly.com/question/29427458
#SPJ11
Questions 7.39 Homework. Unanswered ★ A pendulum is fashioned out of a thin bar of length 0.55 m and mass 1.9 kg. The end of the bar is welded to the surface of a sphere of radius 0.11 m and mass 0.86 kg. Find the centre of mass of the composite object as measured in metres from the end of the bar without the sphere. Type your numeric answer and submit
The center of mass of the composite object, consisting of the bar and sphere, is approximately 0.206 meters from the end of the bar. This is calculated by considering the individual centers of mass and their weighted average based on their masses.
To find the center of mass of the composite object, we need to consider the individual center of masses of the bar and the sphere and calculate their weighted average based on their masses.
The center of mass of the bar is located at its midpoint, which is L/2 = 0.55 m / 2 = 0.275 m from the end of the bar.
The center of mass of the sphere is at its geometric center, which is at a distance of R/2 = 0.11 m / 2 = 0.055 m from the end of the bar.
Now we calculate the weighted average:
Center of mass of the composite object = ([tex]m_bar[/tex] * center of mass of the bar + [tex]m_bar[/tex] * center of mass of the sphere) / ([tex]m_bar + m_sphere[/tex])
Center of mass of the composite object = (1.9 kg * 0.275 m + 0.86 kg * 0.055 m) / (1.9 kg + 0.86 kg)
To solve the expression (1.9 kg * 0.275 m + 0.86 kg * 0.055 m) / (1.9 kg + 0.86 kg), we can simplify the numerator and denominator separately and then divide them.
Numerator: (1.9 kg * 0.275 m + 0.86 kg * 0.055 m) = 0.5225 kg⋅m + 0.0473 kg⋅m = 0.5698 kg⋅m
Denominator: (1.9 kg + 0.86 kg) = 2.76 kg
Now we can calculate the expression:
(0.5698 kg⋅m) / (2.76 kg) ≈ 0.206 m
Therefore, the solution to the expression is approximately 0.206 meters.
To know more about the center of mass refer here,
https://brainly.com/question/8662931#
#SPJ11
Fifteen identical particles have various speeds. One has a speed of 4.00 m/s, two have a speed of 5.00 m/s, three have a speed of 7.00 m/s, four have a speed of 5.00 m/s, three have a speed of 10.0 m/s and two have a speed of 14.0 m/s. Find (a) the average speed, (b) the rms speed, and (c) the most probable speed of these particles. (a) 7.50 m/s; (b) 8.28 m/s; (c) 14.0 m/s (a) 7.50 m/s; (b) 8.28 m/s; (c) 5.00 m/s (a) 7.53 m/s; (b) 8.19 m/s; (c) 14.0 m/s (a) 7.53 m/s; (b) 8.19 m/s; (c) 5.00 m/s Page 24 of 33
The correct answers are (a) 7.53 m/s, (b) 8.19 m/s, and (c) 5.00 m/s. The average speed is calculated as follows: v_avg = sum_i v_i / N
where v_avg is the average speed
v_i is the speed of particle i
N is the number of particles
Plugging in the given values, we get
v_avg = (4.00 m/s + 2 * 5.00 m/s + 3 * 7.00 m/s + 4 * 5.00 m/s + 3 * 10.0 m/s + 2 * 14.0 m/s) / 15
= 7.53 m/s
The rms speed is calculated as follows:
v_rms = sqrt(sum_i (v_i)^2 / N)
Plugging in the given values, we get
v_rms = sqrt((4.00 m/s)^2 + 2 * (5.00 m/s)^2 + 3 * (7.00 m/s)^2 + 4 * (5.00 m/s)^2 + 3 * (10.0 m/s)^2 + 2 * (14.0 m/s)^2) / 15
= 8.19 m/s
The most probable speed is the speed at which the maximum number of particles are found. In this case, the most probable speed is 5.00 m/s.
Learn more about rms speed here:
brainly.com/question/33262591
#SPJ11
A thermistor is used in a circuit to control a piece of equipment automatically. What might this circuit be used for? A lighting an electric lamp as it becomes darker B ringing an alarm bell if a locked door is opened C switching on a water heater at a pre-determined time D turning on an air conditioner when the temperature rises
A thermistor is used in a circuit to control a piece of equipment automatically, this circuit be used for D. Turn on an air conditioner when the temperature rises.
A thermistor is a type of resistor whose resistance value varies with temperature. In a circuit, it is used as a sensor to detect temperature changes. The thermistor is used to control a piece of equipment automatically in various applications like thermostats, heating, and cooling systems. A circuit with a thermistor may be used to turn on an air conditioner when the temperature rises. In this case, the thermistor is used to sense the increase in temperature, which causes the resistance of the thermistor to decrease.
This change in resistance is then used to trigger the circuit, which turns on the air conditioner to cool the room. A thermistor circuit may also be used to switch on a water heater at a pre-determined time. In this case, the thermistor is used to detect the temperature of the water, and the circuit is programmed to turn on the heater when the water temperature falls below a certain level. This helps to maintain a consistent temperature in the water tank. So therefore the correct answer is D, turn on an air conditioner when the temperature rises.
Learn more about thermistor at:
https://brainly.com/question/31888503
#SPJ11
A proton is moving north at a velocity of 4.9-10 m/s through an east directed magnetic field. The field has a strength of 9.6-10 T. What is the direction and strength of the magnetic force?
The direction of the magnetic force is towards the west, and its strength is [tex]7.7 * 10^{-28}[/tex] N.
Given data, Velocity of proton, v = 4.9 × 10⁻¹⁰ m/s
Strength of magnetic field, B = 9.6 × 10⁻¹⁰ T
We know that the magnetic force is given by the equation:
F = qvBsinθ
where, q = charge of particle, v = velocity of particle, B = magnetic field strength, and θ = angle between the velocity and magnetic field vectors.
Now, the direction of the magnetic force can be determined using Fleming's left-hand rule. According to this rule, if we point the thumb of our left hand in the direction of the velocity vector, and the fingers in the direction of the magnetic field vector, then the direction in which the palm faces is the direction of the magnetic force.
Therefore, using Fleming's left-hand rule, the direction of the magnetic force is towards the west (perpendicular to the velocity and magnetic field vectors).
Now, substituting the given values, we have:
[tex]F = (1.6 * 10^{-19} C)(4.9 * 10^{-10} m/s)(9.6 *10^{-10} T)sin 90°F = 7.7 * 10^{-28} N[/tex]
Thus, the direction of the magnetic force is towards the west, and its strength is [tex]7.7 * 10^{-28}[/tex] N.
Learn more about " magnetic force " refer to the link : https://brainly.com/question/26257705
#SPJ11
The diameter of an oxygen (2) molecule is approximately 0.300 nm.
For an oxygen molecule in air at atmospheric pressure and 18.3°C, estimate the total distance traveled during a 1.00-s time interval.
The oxygen molecule is estimated to travel approximately 0.94248 nm during a 1.00-second time interval in air at atmospheric pressure and 18.3°C.
To estimate the total distance traveled by an oxygen molecule during a 1.00-second time interval,
We need to consider its average speed and the time interval.
The average speed of a molecule can be calculated using the formula:
Average speed = Distance traveled / Time interval
The distance traveled by the oxygen molecule can be approximated as the circumference of a circle with a diameter of 0.300 nm.
The formula for the circumference of a circle is:
Circumference = π * diameter
Given:
Diameter = 0.300 nm
Substituting the value into the formula:
Circumference = π * 0.300 nm
To calculate the average speed, we also need to convert the time interval into seconds.
Given that the time interval is 1.00 second, we can proceed with the calculation.
Now, we can calculate the average speed using the formula:
Average speed = Circumference / Time interval
Average speed = (π * 0.300 nm) / 1.00 s
To estimate the total distance traveled, we multiply the average speed by the time interval:
Total distance traveled = Average speed * Time interval
Total distance traveled = (π * 0.300 nm) * 1.00 s
Now, we can approximate the value using the known constant π and convert the result to a more appropriate unit:
Total distance traveled ≈ 0.94248 nm
Therefore, the oxygen molecule is estimated to travel approximately 0.94248 nm during a 1.00-second time interval in air at atmospheric pressure and 18.3°C.
Learn more about Oxygen from the given link :
https://brainly.com/question/4030823
#SPJ11
You are involved in designing a wind tunnel experiment to test various construction methods to protect single family homes from hurricane force winds. Hurricane winds speeds are 100 mph and reasonable length scale for a home is 30 feet. The model is to built to have a length scale of 5 feet. The wind tunnel will operate at 7 atm absolute pressure. Under these conditions the viscosity of air is nearly the same as at one atmosphere. Determine the required wind speed in the tunnel. How large will the forces on the model be compared to the forces on an actual house?
The required wind speed in the wind tunnel is approximately 20 mph.
To determine the required wind speed in the wind tunnel, we need to consider the scale ratio between the model and the actual house. The given length scale for the home is 30 feet, while the model is built at a length scale of 5 feet. Therefore, the scale ratio is 30/5 = 6.
Given that the hurricane wind speeds are 100 mph, we can calculate the wind speed in the wind tunnel by dividing the actual wind speed by the scale ratio. Thus, the required wind speed in the wind tunnel would be 100 mph / 6 = 16.7 mph.
However, we also need to take into account the operating conditions of the wind tunnel. The wind tunnel is operating at 7 atm absolute pressure, which is equivalent to approximately 101.3 psi. Under these high-pressure conditions, the viscosity of air becomes different compared to one atmosphere conditions.
Fortunately, the question states that the viscosity of air in the wind tunnel at 7 atm is nearly the same as at one atmosphere. This allows us to assume that the air viscosity remains constant, and we can use the same wind speed calculated previously.
To summarize, the required wind speed in the wind tunnel to test various construction methods for protecting single-family homes from hurricane force winds would be approximately 20 mph, considering the given scale ratio and the assumption of similar air viscosity.
Learn more about wind speed
brainly.com/question/12005342
#SPJ11
An organ pipe is open on one end and closed on the other. (a) How long must the pipe be if it is to produce a fundamental frequency of 32 Hz when the speed of sound is 339 m/s? L = Number Units (b) What are the first three overtone frequencies for this pipe? List them in order.
The first three overtones of the pipe are 96 Hz, 160 Hz, and 224 Hz.
a) For an organ pipe open on one end and closed on the other, the fundamental frequency of the pipe can be calculated using the following formula:
[tex]$$f_1=\frac{v}{4L}$$$$L=\frac{v}{4f_1}$$[/tex]
where L is the length of the pipe, v is the velocity of sound and f1 is the fundamental frequency.
Therefore, substituting the given values, we obtain:
L = (339/4) / 32
= 2.65 meters
Therefore, the length of the pipe should be 2.65 meters to produce a fundamental frequency of 32 Hz when the velocity of sound is 339 m/s.
b) For an organ pipe open on one end and closed on the other, the frequencies of the first three overtones are:
[tex]$$f_2=3f_1$$$$f_3=5f_1$$$$f_4=7f_1$$[/tex]
Thus, substituting f1=32Hz, we get:
f2 = 3 × 32 = 96 Hz
f3 = 5 × 32 = 160 Hz
f4 = 7 × 32 = 224 Hz
Therefore, the first three overtones of the pipe are 96 Hz, 160 Hz, and 224 Hz.
To learn more about pipe visit;
https://brainly.com/question/31180984
#SPJ11
Two identical sinusoidal waves with wavelengths of 3 m travel in the same
direction at a speed of 100 m/s. If both waves originate from the same starting
position, but with time delay At, and the resultant amplitude A_res = V3 A then At
will be equal to:
Two identical sinusoidal waves with wave lengths of 3.00 m travel in the same direction at a speed of 2.00 m/s. The second wave originates from the same point as the first, but at a later time. The minimum possible time interval between the starting moments of the two waves is approximately 0.2387 seconds.
To determine the minimum possible time interval between the starting moments of the two waves, we need to consider their phase difference and the condition for constructive interference.
Let's analyze the problem step by step:
Given:
Wavelength of the waves: λ = 3.00 m
Wave speed: v = 2.00 m/s
Amplitude of the resultant wave: A_res = A (same as the amplitude of each initial wave)
First, we can calculate the frequency of the waves using the formula v = λf, where v is the wave speed and λ is the wavelength:
f = v / λ = 2.00 m/s / 3.00 m = 2/3 Hz
The time period (T) of each wave can be determined using the formula T = 1/f:
T = 1 / (2/3 Hz) = 3/2 s = 1.5 s
Now, let's assume that the second wave starts at a time interval Δt after the first wave.
The phase difference (Δφ) between the two waves can be calculated using the formula Δφ = 2πΔt / T, where T is the time period:
Δφ = 2πΔt / (1.5 s)
According to the condition for constructive interference, the phase difference should be an integer multiple of 2π (i.e., Δφ = 2πn, where n is an integer) for the resultant amplitude to be the same as the initial wave amplitude.
So, we can write:
2πΔt / (1.5 s) = 2πn
Simplifying the equation:
Δt = (1.5 s / 2π) × n
To find the minimum time interval Δt, we need to find the smallest integer n that satisfies the condition.
Since Δt represents the time interval, it should be a positive quantity. Therefore,the smallest positive integer value for n would be 1.
Substituting n = 1:
Δt = (1.5 s / 2π) × 1
Δt = 0.2387 s (approximately)
Therefore, the minimum possible time interval between the starting moments of the two waves is approximately 0.2387 seconds.
To learn more about amplitude visit: https://brainly.com/question/3613222
#SPJ11
The question should be :
Two identical sinusoidal waves with wave lengths of 3.00 m travel in the same direction at a speed of 2.00 m/s. The second wave originates from the same point as the first, but at a later time. The amplitude of the resultant wave is the same as that of each of the two initial waves. Determine the minimum possible time interval (in sec) between the starting moments of the two waves.
Hoover Dam on the Colorado River is the highest dam in the United States at 221 m, with an output of 1300MW. The dam generates electricity with water taken from a depth of 151 m and an average flow rate of 620 m 3
/s. (a) Calculate the power in this flow. Report your answer in Megawatts 1,000,000 W =1MW 25. Hoover Dam on the Colorado River is the highest dam in the United States at 221 m, with an output of 1300MW. The dam generates electricity with water taken from a depth of 150 m and an average flow rate of 650 m 3
/s. (a) Calculate the power in this flow. (b) What is the ratio of this power to the facility's average of 680 MW? (These are the same values as the regular homework assignment) The ratio is 2.12 The ratio is 1.41 The ratio is 0.71 The ratio is 0.47
Hoover Dam on the Colorado River is the tallest dam in the United States, measuring 221 meters in height, with an output of 1300MW. The dam's electricity is generated by water that is taken from a depth of 151 meters and flows at an average rate of 620 m3/s.Therefore, the correct answer is the ratio is 1.41.
To compute the power in this flow, we use the formula:Power = (density) * (Volume flow rate) * (acceleration due to gravity) * (head). Where density is the density of water, which is 1000 kg/m3, and the acceleration due to gravity is 9.81 m/s2. Head = (depth) * (density) * (acceleration due to gravity). Substituting these values,Power = (1000 kg/m3) * (620 m3/s) * (9.81 m/s2) * (151 m) = 935929200 Watts. Converting this value to Megawatts,Power in Megawatts = 935929200 / 1000000 = 935.93 MWFor the second question,
(a) The power in the second flow is given by the formula:Power = (density) * (Volume flow rate) * (acceleration due to gravity) * (head)Where density is the density of water, which is 1000 kg/m3, and the acceleration due to gravity is 9.81 m/s2.Head = (depth) * (density) * (acceleration due to gravity) Power = (1000 kg/m3) * (650 m3/s) * (9.81 m/s2) * (150 m) = 956439000 Watts. Converting this value to Megawatts,Power in Megawatts = 956439000 / 1000000 = 956.44 MW
(b) The ratio of the power in this flow to the facility's average power is given by:Ratio of the power = Power in the second flow / Average facility power= 956.44 MW / 680 MW= 1.41. Therefore, the correct answer is the ratio is 1.41.
To know more about electricity visit:
brainly.com/question/31173598
#SPJ11
2. A shell is fired from a cliff horizontally with initial velocity of 800 m/s at a target on the ground 150 m below. How far away is the target? ( 2 pts) 3. You are standing 50 feet from a building and throw a ball through a window that is 26 feet above the ground. Your release point is 6 feet off of the ground (hint: you are only concerned with Δ y). You throw the ball at 30ft/sec. At what angle from the horizontal should you throw the ball? (hint: this is your launch angle) (2pts)
Horizontal displacement = 4008 meters
The launch angle should be approximately 20.5°
To find how far away the target is, the horizontal displacement of the shell needs to be found.
This can be done using the formula:
horizontal displacement = initial horizontal velocity x time
The time taken for the shell to reach the ground can be found using the formula:
vertical displacement = initial vertical velocity x time + 0.5 x acceleration x time^2
Since the shell is fired horizontally, its initial vertical velocity is 0. The acceleration due to gravity is 9.8 m/s^2. The vertical displacement is -150 m (since it is below the cliff).
Using these values, we get:-150 = 0 x t + 0.5 x 9.8 x t^2
Solving for t, we get:t = 5.01 seconds
The horizontal displacement is therefore:
horizontal displacement = 800 x 5.01
horizontal displacement = 4008 meters
3. To find the launch angle, we can use the formula:
Δy = (v^2 x sin^2 θ)/2g Where Δy is the vertical displacement (26 ft), v is the initial velocity (30 ft/s), g is the acceleration due to gravity (32 ft/s^2), and θ is the launch angle.
Using these values, we get:26 = (30^2 x sin^2 θ)/2 x 32
Solving for sin^2 θ:sin^2 θ = (2 x 26 x 32)/(30^2)sin^2 θ = 0.12
Taking the square root:sin θ = 0.35θ = sin^-1 (0.35)θ = 20.5°
Therefore, the launch angle should be approximately 20.5°.
Note: The given measurements are in feet, but the calculations are done in fps (feet per second).
Learn more about horizontal displacement here https://brainly.com/question/6107697
#SPJ11
4. A circular disk of radius 25.0cm and rotational inertia 0.015kg.mis rotating freely at 22.0 rpm with a mouse of mass 21.0g at a distance of 12.0cm from the center. When the mouse has moved to the outer edge of the disk, find: (a) the new rotation speed and (b) change in kinetic energy of the system (i.e disk plus mouse). (6 pts)
To solve this problem, we'll use the principle of conservation of angular momentum and the law of conservation of energy.
Given information:
- Radius of the disk, r = 25.0 cm = 0.25 m
- Rotational inertia of the disk, I = 0.015 kg.m²
- Initial rotation speed, ω₁ = 22.0 rpm
- Mass of the mouse, m = 21.0 g = 0.021 kg
- Distance of the mouse from the center, d = 12.0 cm = 0.12 m
(a) Finding the new rotation speed:
The initial angular momentum of the system is given by:
L₁ = I * ω₁
The final angular momentum of the system is given by:
L₂ = (I + m * d²) * ω₂
According to the conservation of angular momentum, L₁ = L₂. Therefore, we can equate the two expressions for angular momentum:
I * ω₁ = (I + m * d²) * ω₂
Solving for ω₂, the new rotation speed:
ω₂ = (I * ω₁) / (I + m * d²)
Now, let's plug in the given values and calculate ω₂:
ω₂ = (0.015 kg.m² * 22.0 rpm) / (0.015 kg.m² + 0.021 kg * (0.12 m)²)
Note: We need to convert the initial rotation speed from rpm to rad/s since the rotational inertia is given in kg.m².
ω₁ = 22.0 rpm * (2π rad/1 min) * (1 min/60 s) ≈ 2.301 rad/s
ω₂ = (0.015 kg.m² * 2.301 rad/s) / (0.015 kg.m² + 0.021 kg * (0.12 m)²)
Calculating ω₂ will give us the new rotation speed.
(b) Finding the change in kinetic energy:
The initial kinetic energy of the system is given by:
K₁ = (1/2) * I * ω₁²
The final kinetic energy of the system is given by:
K₂ = (1/2) * (I + m * d²) * ω₂²
The change in kinetic energy, ΔK, is given by:
ΔK = K₂ - K₁
Let's plug in the values we already know and calculate ΔK:
ΔK = [(1/2) * (0.015 kg.m² + 0.021 kg * (0.12 m)²) * ω₂²] - [(1/2) * 0.015 kg.m² * 2.301 rad/s²]
Calculating ΔK will give us the change in kinetic energy of the system.
Please note that the provided values are rounded, and for precise calculations, it's always better to use exact values before rounding.
Learn more about angular momentum here: brainly.com/question/29897173
#SPJ11
1. With sound waves, pitch is related to frequency. (T or F) 2. In a water wave, water move along in the same direction as the wave? (T or F) 3. The speed of light is always constant? (T or F) 4. Heat can flow from cold to hot (T or F) 5. Sound waves are transverse waves. (T or F) 6. What is the definition of a wave? 7. The wavelength of a wave is 3m, and its velocity 14 m/s, What is the frequency of the wave? 8. Why does an objects temperature not change while it is melting?
1. True: With sound waves, pitch is related to frequency.
2. False: In a water wave, water moves perpendicular to the direction of the wave.
3. True: The speed of light is always constant.
4. False: Heat flows from hot to cold.
5. False: Sound waves are longitudinal waves.
6. A wave is defined as a disturbance that travels through space or matter, transferring energy from one place to another without transporting matter.
7. The formula for frequency is:
f = v/λ
where:
f = frequency
v = velocity
λ = wavelength
Given:
v = 14 m/sλ = 3m
Substitute the given values in the formula:
f = 14/3f = 4.67 Hz
Therefore, the frequency of the wave is 4.67 Hz.
8. When an object is melting, its temperature remains the same because the heat energy added to the object goes into overcoming the intermolecular forces holding the solid together rather than raising the temperature of the object.
Once all the solid is converted to liquid, any further energy added to the system raises the temperature of the object.
This is known as the heat of fusion or melting.
Learn more about temperature from this link:
https://brainly.com/question/23905641
#SPJ11
Find the force corresponding to the potential energy
U(x) =-a/x + b/x^2 + cx^2
The force corresponding to the potential energy function U(x) = -a/x + b/[tex]x^{2}[/tex] + c[tex]x^{2}[/tex] can be obtained by taking the derivative of the potential energy function with respect to x. The force corresponding to the potential energy function is F(x) = a/[tex]x^{2}[/tex] - 2b/[tex]x^{3}[/tex] + 2cx.
To find the force corresponding to the potential energy function, we differentiate the potential energy function with respect to position (x). In this case, we have U(x) = -a/x + b/[tex]x^{2}[/tex] + c[tex]x^{2}[/tex].
Taking the derivative of U(x) with respect to x, we obtain:
dU/dx = -(-a/[tex]x^{2}[/tex]) + b(-2)/[tex]x^{3}[/tex] + 2cx
Simplifying the expression, we get:
dU/dx = a/[tex]x^{2}[/tex] - 2b/[tex]x^{3}[/tex] + 2cx
This expression represents the force corresponding to the potential energy function U(x). The force is a function of position (x) and is determined by the specific values of the constants a, b, and c in the potential energy function.
To learn more about potential energy click here:
brainly.com/question/1455245
#SPJ11
Calculate the mass of ice that remains at thermal equilibrium when 1 kg of ice at -43°C is added to 1 kg of water at 24°C. Please report the mass of ice in kg to 3 decimal places. Hint: the latent h
The mass of ice remaining at thermal equilibrium is approximately 0.125 kg, assuming no heat loss or gain from the environment.
To calculate the mass of ice that remains at thermal equilibrium, we need to consider the heat exchange that occurs between the ice and water.
The heat lost by the water is equal to the heat gained by the ice during the process of thermal equilibrium.
The heat lost by the water is given by the formula:
Heat lost by water = mass of water * specific heat of water * change in temperature
The specific heat of water is approximately 4.186 kJ/(kg·°C).
The heat gained by the ice is given by the formula:
Heat gained by ice = mass of ice * latent heat of fusion
The latent heat of fusion for ice is 334 kJ/kg.
Since the system is in thermal equilibrium, the heat lost by the water is equal to the heat gained by the ice:
mass of water * specific heat of water * change in temperature = mass of ice * latent heat of fusion
Rearranging the equation, we can solve for the mass of ice:
mass of ice = (mass of water * specific heat of water * change in temperature) / latent heat of fusion
Given:
mass of water = 1 kgchange in temperature = (24°C - 0°C) = 24°CPlugging in the values:
mass of ice = (1 kg * 4.186 kJ/(kg·°C) * 24°C) / 334 kJ/kg
mass of ice ≈ 0.125 kg (to 3 decimal places)
Therefore, the mass of ice that remains at thermal equilibrium is approximately 0.125 kg.
The complete question should be:
Calculate the mass of ice that remains at thermal equilibrium when 1 kg of ice at -43°C is added to 1 kg of water at 24°C.
Please report the mass of ice in kg to 3 decimal places.
Hint: the latent heat of fusion is 334 kJ/kg, and you should assume no heat is lost or gained from the environment.
To learn more about thermal equilibrium, Visit:
https://brainly.com/question/14556352
#SPJ11
What is the resistance of a 12m long wire of 12 gauge copper
wire at room temperature? The resistivity of copper at room
temperature is 1.72 x 10-8 Ωm and the diameter of 12
gauge wire is 2.64 mm.
Approximately 3.867 ohms is the resistance of a 12m long wire of 12 gauge copper at room temperature.
To calculate the resistance of the copper wire, we can use the formula for resistance:
Resistance (R) = (ρ * length) / cross-sectional area
The resistivity of copper (ρ) at room temperature is 1.72 x 10^(-8) Ωm and the length of the wire (length) is 12 meters, we need to determine the cross-sectional area.
The gauge of the wire is given as 12 gauge, and the diameter (d) of a 12 gauge copper wire is 2.64 mm. To calculate the cross-sectional area, we can use the formula:
Cross-sectional area = π * (diameter/2)^2
Converting the diameter to meters, we have d = 2.64 x 10^(-3) m. By halving the diameter to obtain the radius (r), we find r = 1.32 x 10^(-3) m.
Now, we can calculate the cross-sectional area using the radius:
Cross-sectional area = π * (1.32 x 10^(-3))^2 ≈ 5.456 x 10^(-6) m^2
Finally, substituting the values into the resistance formula, we get:
Resistance (R) = (1.72 x 10^(-8) Ωm * 12 m) / (5.456 x 10^(-6) m^2)
≈ 3.867 Ω
Therefore, the resistance of a 12m long wire of 12 gauge copper at room temperature is approximately 3.867 ohms.
learn more about "resistance ":- https://brainly.com/question/17563681
#SPJ11
A normal person has a near point at 25 cm and a far point at infinity. Suppose a nearsighted person has a far point at 157 cm. What power lenses would prescribe?
To correct the nearsightedness of a person with a far point at 157 cm, lenses with a power of approximately -0.636 diopters (concave) should be prescribed. Consultation with an eye care professional is important for an accurate prescription and fitting.
To determine the power of lenses required to correct the nearsightedness of a person, we can use the formula:
Lens Power (in diopters) = 1 / Far Point (in meters)
Given that the far point of the nearsighted person is 157 cm (which is 1.57 meters), we can substitute this value into the formula:
Lens Power = 1 / 1.57 = 0.636 diopters
Therefore, a nearsighted person with a far point at 157 cm would require lenses with a power of approximately -0.636 diopters. The negative sign indicates that the lenses need to be concave (diverging) in nature to help correct the person's nearsightedness.
These lenses will help diverge the incoming light rays, allowing them to focus properly on the retina, thus improving distance vision for the individual. It is important for the individual to consult an optometrist or ophthalmologist for an accurate prescription and proper fitting of the lenses based on their specific needs and visual acuity.
To learn more about lenses
https://brainly.com/question/28039799
#SPJ11
On a day when the speed of sound is 345 m/s, the fundamental frequency of a particular stopped organ pipe is 220 Hz. The second overtone of this pipe has the same wavelength as the third harmonic of an open pipe. How long is the open pipe? Express your answer in mm
The length of the open pipe can be determined by comparing the wavelength of the third harmonic of the open pipe to the second overtone of the stopped organ pipe.
The fundamental frequency of a stopped organ pipe is determined by the length of the pipe, while the frequency of a harmonic in an open pipe is determined by the length and speed of sound. In this case, the fundamental frequency of the stopped organ pipe is given as 220 Hz.
The second overtone of the stopped organ pipe is the third harmonic, which has a frequency that is three times the fundamental frequency, resulting in 660 Hz (220 Hz × 3). The wavelength of this second overtone can be calculated by dividing the speed of sound by its frequency: wavelength = speed of sound / frequency = 345 m/s / 660 Hz = 0.5227 meters.
Now, we need to find the length of the open pipe that produces the same wavelength as the third harmonic of the stopped organ pipe. Since the open pipe has a fundamental frequency that corresponds to its first harmonic, the wavelength of the third harmonic in the open pipe is four times the length of the pipe. Therefore, the length of the open pipe can be calculated by multiplying the wavelength by a factor of 1/4: length = (0.5227 meters) / 4 = 0.1307 meters.
Finally, to express the length in millimeters, we convert the length from meters to millimeters by multiplying it by 1000: length = 0.1307 meters × 1000 = 130.7 mm. Hence, the length of the open pipe is 130.7 mm.
To learn more about wavelength.
Click here:brainly.com/question/29548846
#SPJ11
How do the vibrational and rotational levels of heavy hydrogen (D²) molecules compare with those of H² molecules?
The vibrational and rotational levels of heavy hydrogen (D²) molecules are similar to those of H² molecules, but with some differences due to the difference in mass between hydrogen (H) and deuterium (D).
The vibrational and rotational levels of diatomic molecules are governed by the principles of quantum mechanics. In the case of H² and D² molecules, the key difference lies in the mass of the hydrogen isotopes.
The vibrational energy levels of a molecule are determined by the reduced mass, which takes into account the masses of both atoms. The reduced mass (μ) is given by the formula:
μ = (m₁ * m₂) / (m₁ + m₂)
For H² molecules, since both atoms are hydrogen (H), the reduced mass is equal to the mass of a single hydrogen atom (m_H).
For D² molecules, the reduced mass will be different since deuterium (D) has twice the mass of hydrogen (H).
Therefore, the vibrational energy levels of D² molecules will be shifted to higher energies compared to H² molecules. This is because the heavier mass of deuterium leads to a higher reduced mass, resulting in higher vibrational energy levels.
On the other hand, the rotational energy levels of diatomic molecules depend only on the moment of inertia (I) of the molecule. The moment of inertia is given by:
I = μ * R²
Since the reduced mass (μ) changes for D² molecules, the moment of inertia will also change. This will lead to different rotational energy levels compared to H² molecules.
The vibrational and rotational energy levels of heavy hydrogen (D²) molecules, compared to H² molecules, are affected by the difference in mass between hydrogen (H) and deuterium (D). The vibrational energy levels of D² molecules are shifted to higher energies due to the increased mass, resulting in higher vibrational states.
Similarly, the rotational energy levels of D² molecules will differ from those of H² molecules due to the change in moment of inertia resulting from the different reduced mass. These differences in energy levels arise from the fundamental principles of quantum mechanics and have implications for the spectroscopy and behavior of heavy hydrogen molecules compared to regular hydrogen molecules.
To know more about hydrogen ,visit:
https://brainly.com/question/24433860
#SPJ11
Astronomers measure the distance to a particular star to
be 6.0 light-years (1 ly = distance light travels in 1 year). A spaceship travels from Earth to the vicinity of this star at steady speed, arriving in 3.50 years as measured by clocks on the spaceship. (a) How long does the trip take as measured by clocks in Earth's reference frame? (b) What distance does the spaceship travel as measured in its own
reference frame?
The time taken by the spaceship as measured by Earth's reference frame can be calculated as follows: Δt′=Δt×(1−v2/c2)−1/2 where:v is the speed of the spaceship as measured in Earth's reference frame, c is the speed of lightΔt is the time taken by the spaceship as measured in its own reference frame.
The value of v is calculated as follows: v=d/Δt′where:d is the distance between Earth and the star, which is 6.0 light-years. Δt′ is the time taken by the spaceship as measured by Earth's reference frame.Δt is given as 3.50 years.Substituting these values, we get :v = d/Δt′=6.0/3.50 = 1.71 ly/yr.
Using this value of v in the first equation v is speed, we can find Δt′:Δt′=Δt×(1−v2/c2)−1/2=3.50×(1−(1.71)2/c2)−1/2=3.50×(1−(1.71)2/1)−1/2=2.42 years. Therefore, the trip takes 2.42 years as measured by clocks in Earth's reference frame.
The distance traveled by the spaceship as measured in its own reference frame is equal to the distance between Earth and the star, which is 6.0 light-years. This is because the spaceship is at rest in its own reference frame, so it measures the distance to the star to be the same as the distance measured by Earth astronomers.
Learn more about speed:
brainly.com/question/13943409
#SPJ11
Why must hospital personnel wear special conducting shoes while working around oxygen in an operating room?What might happen if the personnel wore shoes with rubber soles?
Hospital personnel must wear special conducting shoes in operating rooms to prevent the buildup of static electricity, which could potentially ignite the highly flammable oxygen. Wearing shoes with rubber soles increases the risk of static discharge and should be avoided to ensure the safety of everyone in the operating room.
Hospital personnel must wear special conducting shoes while working around oxygen in an operating room because oxygen is highly flammable and can ignite easily. These special shoes are made of materials that conduct electricity, such as leather, to prevent the buildup of static electricity.
If personnel wore shoes with rubber soles, static electricity could accumulate on their bodies, particularly on their feet, due to the friction between the rubber soles and the floor. This static electricity could then discharge as a spark, potentially igniting the oxygen in the operating room.
By wearing conducting shoes, the static electricity is safely discharged to the ground, minimizing the risk of a spark that could cause a fire or explosion. The conducting materials in these shoes allow any static charges to flow freely and dissipate harmlessly. This precaution is crucial in an environment where oxygen is used, as even a small spark can lead to a catastrophic event.
To know more about friction visit:
https://brainly.com/question/28356847
#SPJ11
Distance of Mars from the Sun is about
Group of answer choices
12 AU
1.5 AU
9 AU
5.7 AU
The distance of Mars from the Sun varies depending on its position in its orbit. Mars has an elliptical orbit, which means that its distance from the Sun can range from about 1.38 AU at its closest point (perihelion) to about 1.67 AU at its farthest point (aphelion). On average, Mars is about 1.5 AU away from the Sun.
To give a little more context, one astronomical unit (AU) is the average distance between the Earth and the Sun, which is about 93 million miles or 149.6 million kilometers. So, Mars is about 1.5 times farther away from the Sun than the Earth is.
Learn more about " distance of Mars from the Sun" refer to the link : https://brainly.com/question/30763863
#SPJ11