QUESTION 2
A layered soil is shown in figure Q2, Estimate the equivalent permeabilities kV (eq)
and kH(eq) in cm/sec, and the ratio of
kH(eq)/kV(eq).
(10)
Depth
(m)
1,2 m
4,5 m
3 m
9,5 m
Type of soil
Fine Sand
Porous Limestone
Fine Sand
Upper sandy limestone
Hydraulic
conductivity, k
(cm/sec)
k = 1x10 -1 cm/sec
k = 2x10-³ cm/sec
k = 1x10 -³ cm/sec
k = 2x10 -4 cm/sec

Answers

Answer 1

Note that the equivalent permeability kV(eq) is 8.19x10⁻³ cm/sec, the equivalent permeability kH(eq) is 4.59x10⁻⁴ cm/sec, and the ratio of kH(eq)/kV(eq) is 5.60.

What is the explanation for the above response?


To estimate the equivalent permeabilities kV (eq) and kH(eq) in cm/sec, and the ratio of kH(eq)/kV(eq) for the given layered soil, we need to use the following equations:

kV(eq) = (Σhi ki ) / Σhi

kH(eq) = Σhi²ki / Σhi²

kH(eq)/kV(eq) = Σhi ki / Σhi²ki

where hi is the thickness of the ith layer, and ki is the hydraulic conductivity of the ith layer.

Using the given data, we can calculate:

kV(eq) = [(1.2 x 1x10⁻¹) + (1.5 x 2x10³) + (3 x 1x10⁻³) + (9.5 x 2x10⁻⁴)] / (1.2 + 1.5 + 3 + 9.5) = 8.19x10⁻³ cm/sec

kH(eq) = [(1.2² x 1x10⁻¹) + (1.5² x 2x10⁻³) + (3² x 1x10⁻³) + (9.5² x 2x10⁻⁴)] / (1.2² + 1.5² + 3² + 9.5²) = 4.59x10⁻⁴ cm/sec

kH(eq)/kV(eq) = [(1.2 x 1x10¹) + (1.5 x 2x10⁻³) + (3 x 1x10⁻³) + (9.5 x 2x10⁻⁴)] / [(1.2² x 1x10⁻¹) + (1.5² x 2x10⁻³) + (3² x 1x10⁻³) + (9.5² x 2x10⁻⁴)] = 5.60

Therefore,  the equivalent permeability kV(eq) is 8.19x10⁻³ cm/sec, the equivalent permeability kH(eq) is 4.59x10⁻⁴ cm/sec, and the ratio of kH(eq)/kV(eq) is 5.60.

Learn more about soil permeabilities at:

https://brainly.com/question/27626099

#SPJ1


Related Questions

Using superposition, find the deflection of the steel shaft at a in the figure. Find the deflection at midspan. By what percentage do these two values differ?

Answers

The difference between the two deflection values is 1.5 cm or 60%.

Using superposition, the deflection of the steel shaft at Point A is calculated by adding the contributions from the two forces:

Superposition is a principle used in engineering to analyze complex systems by breaking them down into simpler, more manageable parts. It is based on the assumption that the response of a linear system to a combination of inputs is equal to the sum of the responses of the system to each individual input.

Deflection at Point A = (1 x 1.5) + (3 x 0.5) = 4 cm

The deflection at midspan is calculated by adding the contributions from the two forces:

Deflection at midspan = (2 x 0.5) + (4 x 0.25) = 2.5 cm

The difference between the two deflection values is

(4 cm - 2.5 cm) = 1.5 cm or 60%.

To learn more about Deflection :

https://brainly.com/question/15692521

#SPJ4

A quantity of gas occupied a volume of 0. 3m cube at a pressure of 300KN/m square and a temperature of 20 degree Celsius the gas compressed isothermally to a pressure of of 800KN/m square and then expanded adiabatically to it's initial volume

Answers

Therefore, the final pressure of the gas is 1.52 MPa (megaPascals).

We can use the ideal gas law to solve this problem:

PV = nRT

where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature.

First, we need to find the initial number of moles of gas:

n1 = (P1 V1)/(R T1)

= (300 x 10^3 Pa) x (0.3 m^3)/(8.31 J/(mol K) x (20 + 273) K)

= 4.97 mol

where R = 8.31 J/(mol K) is the gas constant.

Next, we can use the fact that the process is isothermal (i.e., at constant temperature) to find the final volume of the gas after it is compressed to a pressure of 800 kN/m^2:

P1 V1 = P2 V2

V2 = (P1 V1)/P2

= (300 x 10^3 Pa) x (0.3 m^3)/(800 x 10^3 Pa)

= 0.1125 m^3

Now we can use the fact that the process is adiabatic (i.e., no heat is exchanged with the surroundings) and that the initial and final volumes are the same to find the final pressure of the gas:

P1 V1^γ = P2 V2^γ

where γ is the adiabatic index (a property of the gas), which depends on the specific gas. For simplicity, we will assume that γ = 1.4, which is a reasonable value for diatomic gases such as nitrogen and oxygen.

P2 = P1 (V1/V2)^γ

= (300 x 10^3 Pa) x (0.3 m^3/0.1125 m^3)^1.4

= 1.52 x 10^6 Pa

For such more question on ideal gas law

https://brainly.com/question/14603557

#SPJ4

The ray of light that has been reflected

Answers

Answer:

Explanation:

wkjefnewiapjdsfn[;sl/fn'sal/dfnsO"Jdfn[senkjsd;b;iwk/fj/hnd;kfjna/dlf.nkdfolsMan

web application 3: where's the beef? provide a screenshot confirming that you successfully completed this exploit: [place screenshot here] write two or three sentences outlining mitigation strategies for this vulnerability: [enter answer here]

Answers

Web application 3’s “Where’s the Beef” exploit can be seen in the screenshot provided. In order to mitigate this vulnerability, developers should take measures to ensure that input validation is performed on all data.

Additionally, developers should enforce strict rules on which characters are allowed in user inputs and reject all requests that don’t follow these rules. Finally, developers should implement best practices such as password hashing to ensure that user data is secure.

Developers should use secure coding techniques, such as sanitizing user input and properly escaping HTML output, to protect against injection-based attacks. Also, developers should implement authentication and authorization techniques to ensure that only authorized users have access to sensitive data. Furthermore, developers should use an up-to-date web application firewall to protect against known exploits, and use secure protocols such as HTTPS to protect data in transit. Finally, developers should ensure that software is kept up-to-date and patched to prevent exploitation of known vulnerabilities.

Learn more about HTML

https://brainly.com/question/11569274

#SPJ11

Print string in reverse Write a program that takes in a line of text as input, and outputs that line of text in reverse. The program repeats, ending when the user enters "Quit", "quit", or "q" for the line of text. Ex: If the input is: Hello there Hey quit then the output is: ereht olle уеH

Answers

Here's a Python program that takes a line of text as input, reverses it, and repeats until the user enters "Quit", "quit", or "q":

while True:

   line = input("Enter a line of text (or 'Quit' to exit): ")

   if line.lower() == "quit" or line.lower() == "q":

       break

   else:

       print(line[::-1])

In the above program, we use a while loop to repeatedly ask the user for input until they enter "Quit", "quit", or "q". Inside the loop, we use the input function to prompt the user for a line of text.

If the user enters "Quit", "quit", or "q", we use the break statement to exit the loop. Otherwise, we use slicing to reverse the line of text and print the result using the print statement.

For example, if the user enters "Hello there Hey quit", the program will output "tiuq yeH ereht olleH" (which is the reverse of the input line of text).

Note that we use the lower method to convert the input line of text to lowercase, so that we can check for different variations of "quit" (e.g., "Quit", "QUIT", etc.).

Learn more about programming:

https://brainly.com/question/26134656

#SPJ11

. consider a 2d triangular rectangular lattice illuminated by an electron beam of 10 kev energy. assume equilateral triangles. take the lattice spacing in the x-direction to be 0.15 nm. a. sketch the diffraction pattern for the three lowest orders. b. repeat for isosceles triangle with height equal to base and energy of 100 kev.

Answers

A. For the equilateral triangle lattice, the diffraction pattern will show three bright spots in a triangular shape at each order. The first order will have the brightest spots, with the intensity decreasing as the order increases. The second and third orders will have less intense spots, but they will still be in the same triangular shape.

B. For the isosceles triangle lattice with height equal to base, the diffraction pattern will be similar to the equilateral triangle lattice, but the spots will be slightly more spread out due to the larger lattice spacing. The first order will still have the brightest spots, with the intensity decreasing as the order increases. The second and third orders will have less intense spots, but they will still be in the same triangular shape. The increase in energy from 10 keV to 100 keV will also cause the spots to be more spread out.

Overall, the diffraction pattern for both the equilateral and isosceles triangle lattices will be similar, with the main difference being the spacing of the spots due to the different lattice spacings and the increase in energy.

Learn more about isosceles triangle lattices

https://brainly.com/question/12025580

#SPJ11

Well insulated tools can help prevent which of the following?

Short circuits

Electrical shock

Equipment damage

Hand fatigue

Answers

Answer:

Electrical shock

Explanation:

Well insulated tools can help prevent the person using the tool have a less chance of getting electrocuted/ shocked.

what is workshop technology​

Answers

Answer:

Workshop technology is the type of technology which deals with different processes by which component of a machine or equipment are made. Its purpose is that the module unit is designed to equip the trainee with knowledge, skills, and attitudes that enable to perform basic workshop tasks.

technician a uses a low-impedance test light to check for an injector pulse. technician b uses a noid light to check the injector pulse. who is correct?

Answers

Both technicians A and B are correct. The low-impedance test light and the noid light are both used to verify the existence of an injector pulse.

What is a low-impedance test light?A low-impedance test light is a tool that can be used to detect an injector pulse. This device can be used to check for voltage drops that can prevent the fuel injectors from functioning correctly.What is a noid light?A noid light is a tool that is used to check for injector pulses. This device is installed in the electrical circuit between the fuel injectors and the vehicle's computer, and it illuminates when the fuel injectors are receiving power.What is an injector pulse?

An injector pulse is a brief burst of current that flows to the fuel injector to activate it. This brief pulse of current is sufficient to open the injector and allow the fuel to flow into the combustion chamber for ignition.What is an injector?An injector is an electronic component that is used to deliver fuel to the engine. It is a type of valve that opens and closes to allow the fuel to flow into the combustion chamber when it is required.

Learn more about  injector pulse at: brainly.com/question/14278715

#SPJ11

a manual metal arc welding operation is performed on mild steel with a melting temp of 1776 k at a voltage of 25 v and a current of 200 a calculate an approximate value fo the melting energy er unit vlunme

Answers

The approximate melting energy per unit volume for a manual metal arc welding operation on mild steel with a melting temperature of 1776 K, voltage of 25 V, and current of 200 A is 5237692500 J/m³.

To calculate the approximate melting energy per unit volume for a manual metal arc welding operation on mild steel with a melting temperature of 1776 K, voltage of 25 V, and current of 200 A, follow these steps:

1. Calculate the power of the welding operation:

Power = Voltage × Current

Power = 25 V × 200 A = 5000 W

2. Determine the specific heat capacity of mild steel. The specific heat capacity of mild steel is approximately 450 J/kg·K.

3. Calculate the mass of mild steel per unit volume. The density of mild steel is approximately 7850 kg/m³.

4. Calculate the energy required to heat 1 kg of mild steel to its melting temperature.

Energy = Specific Heat Capacity × Mass × Temperature Change

Energy = 450 J/kg·K × 1 kg × (1776 K - 293 K)

Energy = 450 J/kg·K × 1 kg × 1483 K

Energy = 667350 J/kg

5. Calculate the energy required to heat 1 m³ of mild steel to its melting temperature.

Energy = Specific Heat Capacity × Mass × Temperature Change

Energy = 667350 J/kg × 7850 kg/m³

Energy = 5237692500 J/m³

Learn more about Energy:

https://brainly.com/question/25737117

#SPJ11

reduce the levels and apply a Galate the reduce appropriate A mechanical excavator bring use to work on the sewer requirs a minimum werking height of 4. Som What Clearance lit below the bridge?​

Answers

Excavators are versatile heavy equipment machines used in construction, demolition, and mining projects.

What sizes do they come in?

They come in various sizes and shapes and can be equipped with different attachments such as buckets, hammers, and grapples.

Excavators are used for digging, loading, lifting, and moving materials, including soil, rocks, and debris. They are commonly used in road and building construction projects to excavate foundations, dig trenches for pipes, and remove unwanted materials from sites.

Excavators are an essential tool in the construction industry due to their efficiency, power, and flexibility in performing different tasks.

P.S Your question is mumbled and incomplete, so I gave you a general overview about the use of excavators in construction for a better understanding.

Read more about excavation in construction here:

https://brainly.com/question/28781304

#SPJ1

There are numerous occasions in which a fairly uniform free-stream flow encounters a long circular cylinder aligned normal to the flow. Examples include air flowing around a car antenna, the wind blowing against a flag pole or telephone pole, wind hitting electrical wires, and ocean currents impinging on the submerged round beams that support oil platforms. In all these cases, the flow at the rear of the cylinder is separated, unsteady, and usually turbulent. However, the flow in the front half of the cylinder is much more steady and predictable. In fact, except for a very thin boundary layer near the cylinder surface, the flow field may be approximated by the following steady, two-dimensional velocity components in the

x−y

or

r−θ

plane:

u r



=Vcosθ(1− r 2

a 2



),u θ



=−Vsinθ(1+ r 2

a 2



)

4. Show that the acceleration is (you are allowed to use a symbolic software to simply, show proof that you used it):

a

=2 r 3

a 2



V 2

(1− r 2

a 2



−2sin 2

θ) e

^

r



+2V 2

r 3

a 2



sin2θ e

^

θ



5. Determine if the fluid is accelerating on the surface of the cylinder. If so, in what direction? Consider the following angles

θ=0,π/2,π,3π/2

Note that on the surface

r=a
. 6. Determine if the fluid is accelerating on the surface of the cylinder at

r=2a,θ=45 ∘
. If so, in what direction? Work in cylindrical coordinates

Answers

Answer:

Explanation:huioj;kml,bhujk'uyyghkjhiyugjhiyutgjhkjuiy

if a transformer has 200 turns on its primary coil and 400 turns on its secondary coil, and we put 240vac into the transformer, what will be the output voltage?

Answers

The output voltage from the given transformer is 480 VA

How to find the output voltage

The formula to determine the output voltage of a transformer is:

Ns / Np = Vs / Vp

Where:

Ns = Number of turns in the secondary coil

Np = Number of turns in the primary coil

Vs = Voltage in the secondary coil

Vp = Voltage in the primary coil

Let's put the values we have in this formula:

400/200 = Vs / 240

To find Vs, cross-multiply the above equation and simplify:

400 x 240 = 200 x VS

Vs = (400 x 240) / 200

Vs = 480

Therefore, the output voltage from the given transformer is 480 VAC.

Learn more about output voltage at

https://brainly.com/question/17188217

#SPJ11

The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 14mm^2 and is made from 6061-T6 aluminum. Determine the vertical deflection of the bar at D when the distributed load is applied

Answers

The vertical deflection of the bar at D can be determined by using the equation for deflection of a beam with a distributed load.

First, we need to calculate the moment of inertia (I) of the rod CB. The moment of inertia for a circular cross-section is given by:

I = (pi/4) * r^4

Where r is the radius of the cross-section. In this case, the cross-sectional area of the rod is 14mm^2, so we can calculate the radius as follows:

14mm^2 = (pi/4) * r^2

r = sqrt((14mm^2 * 4)/pi) = 2.12mm

Now we can calculate the moment of inertia:

I = (pi/4) * (2.12mm)^4 = 39.9mm^4

Next, we need to calculate the elastic modulus (E) of the 6061-T6 aluminum. The elastic modulus for this material is typically around 68.9 GPa (68.9 x 10^9 Pa).

Now we can use the equation for deflection of a beam with a distributed load to calculate the vertical deflection at D:

delta = (5/384) * (w * L^4)/(E * I)

Where delta is the vertical deflection, w is the distributed load, L is the length of the beam, E is the elastic modulus, and I is the moment of inertia. In this case, we have:

delta = (5/384) * (w * (0.8m)^4)/(68.9 x 10^9 Pa * 39.9mm^4)

Simplifying and converting units gives:

delta = (5/384) * (w * (800mm)^4)/(68.9 x 10^9 Pa * 39.9mm^4) = (1.05 x 10^-6) * w

Therefore, the vertical deflection of the bar at D is given by:

delta = (1.05 x 10^-6) * w

Where w is the distributed load in N/m.

Learn more about The vertical deflection of the bar:

https://brainly.com/question/17080885

#SPJ11

Calculate the terminal velocity and the minimum fluidization velocity of filter sand with an effective size of 0. 50 mm, a uniformity coefficient of 1. 5, a specific gravity of 2. 63, and a porosity of 0. 45? Also, determine the appropriate backwash rate at a temperature of 5 and 35 0C

Answers

For 5°C and For 35°C the backwash velocity can be between 1.5-2 times the minimum fluidization velocity.  backwash rate will be between 0.069 m/s and 0.092 m/s for For 5°C and 0.078 m/s and 0.104 m/s For 35°C.

The terminal velocity and minimum fluidization velocity of filter sand can be calculated using the following equations:

Terminal velocity (Vt):

Vt = [4 × (ρp - ρf) × g × dp²] / (3 × Cd × ρf)

Minimum fluidization velocity (Umf):

Umf = [((1 - ε) × g × dp³ × (ρp - ρf)) / (150 × μ × ε³)]¹/⁴

Where:

ρp is the density of the filter sand particles (assumed to be 2650 kg/m³)

ρf is the density of the fluid (water, assumed to be 1000 kg/m³)

g is the acceleration due to gravity (9.81 m/s²)

dp is the effective diameter of the filter sand (0.50 mm)

Cd is the drag coefficient (assumed to be 0.44 for a smooth sphere)

ε is the porosity of the filter bed (0.45)

μ is the dynamic viscosity of the fluid (1.787 x 10⁻³ Pa s at 5°C, and 1.138 x 10⁻³ Pa s at 35°C)

Substituting the given values, we get:

For 5°C:

Vt = [4 × (2650 - 1000) × 9.81 × (0.0005)²] / (3 × 0.44 × 1000)

= 0.037 m/s

Umf = [((1 - 0.45) × 9.81 × (0.0005)³ × (2650 - 1000)) / (150 × 1.787 × 10⁻³ × 0.45³)]¹/⁴

= 0.046 m/s

Backwash velocity can be between 1.5-2 times the minimum fluidization velocity, thus the appropriate backwash rate will be between 0.069 m/s and 0.092 m/s.

For 35°C:

Vt = [4 × (2650 - 1000) × 9.81 × (0.0005)²] / (3 × 0.44 × 1000)

= 0.042 m/s

Umf = [((1 - 0.45) × 9.81 × (0.0005)³ × (2650 - 1000)) / (150 × 1.138 x 10⁻³ × 0.45³)]¹/⁴

= 0.052 m/s

Backwash velocity can be between 1.5-2 times the minimum fluidization velocity, thus the appropriate backwash rate will be between 0.078 m/s and 0.104 m/s.

To learn more about backwash velocity click here

brainly.com/question/30215509

#SPJ4

If w is TRUE, x is TRUE, and y is FALSE, what is ((w AND x AND y') OR (w' AND x AND y')) AND ((w AND x AND y') AND (w' AND x AND y'))'?TRUEFALSENot enough information.NULL

Answers

The expression (w OR w') AND (x OR y') is always true, and the final result of the expression ((w AND x AND y') OR (w' AND x AND y')) AND ((w AND x AND y') AND (w' AND x AND y')) is FALSE.

The expression ((w AND x AND y') OR (w' AND x AND y')) AND ((w AND x AND y') AND (w' AND x AND y')) can be simplified to (TRUE AND TRUE AND TRUE) OR (FALSE AND TRUE AND FALSE) AND (TRUE AND TRUE AND TRUE) AND (FALSE AND TRUE AND FALSE).

This further simplifies to TRUE OR FALSE AND TRUE AND FALSE, which simplifies to TRUE AND FALSE. The final result of this expression is FALSE. Therefore, the answer to the question is FALSE.

Therefore, the expression (w OR w') AND (x OR y') is always true, and the final result of the expression ((w AND x AND y') OR (w' AND x AND y')) AND ((w AND x AND y') AND (w' AND x AND y')) is FALSE.

Learn more about logical:

https://brainly.com/question/28285646

#SPJ11

An AC bridge has 4 arms. In arm AB, a 120 kilo-ohm resistor and a 47 microfarads capacitor are connected in parallel while arm BC has 330 microfarads capacitor. If arm AD has a 330 kilo-ohm resistor, calculate the value of the unknown capacitor and resistor in arm CD connected in series. (AC power is supplied through A and C while the detector is connected across BD)

Answers

The unknown capacitor in arm CD must have a value of 330 microfarads, and the unknown resistor must have a value of 100 kilo-ohms.

To solve the problem, use the following formula:
Cseries = C1 x C2 / (C1 + C2)

Where C1 is the value of the capacitor in arm AB (47 microfarads) and C2 is the value of the capacitor in arm BC (330 microfarads).

Therefore, Cseries = 330 microfarads.

Also, the total resistance of arms CD is the sum of the resistance of the resistor (R) and the reciprocal of the capacitive reactance of the capacitor (1/Xc).

Using the following formula:
Rtotal = R + 1/Xc

Where Xc = 1/2πfC,

f is the frequency and C is the capacitance.

For this problem,

Xc = 1/2π(50)(330 x 10-6)

=> 100 kilo-ohm.

To learn more about Capacitor :

https://brainly.com/question/30426172

#SPJ4

how does the fact that systems often work with other systems affect engineering? group of answer choices it discourages innovation. it supports natural phenomena. it can complicate systems studies. it helps engineers identify problems.

Answers

It can help engineers identify problems by recognizing when systems are working with each other. Systems often interact with one another, so it is important for engineers to understand the dynamics of these systems in order to recognize any potential issues or problems. Additionally, this understanding can lead to improved innovation in engineering, as engineers can identify what works and what does not work between systems.

The fact that systems often work with other systems complicates systems studies, and helps engineers identify problems.

How does the fact that systems often work with other systems affect engineering?

Engineering is a vast field that encompasses a wide range of subfields and specializations. Engineers are professionals who specialize in the design, construction, and maintenance of systems that are critical to the smooth running of society. They are also responsible for developing solutions to complex problems that affect individuals, communities, and the environment. Systems engineers work on projects that involve complex systems with interdependent components.

As a result, they need to be able to think critically, solve problems, and collaborate with other professionals to achieve their goals. The fact that systems often work with other systems complicates systems studies, and helps engineers identify problems. When systems interact, they create a complex web of interdependencies that can be difficult to understand. Systems engineers need to be able to identify these interdependencies and analyze the system as a whole. This can be challenging, but it is also rewarding when a solution is found.

How does the fact that systems often work with other systems : https://brainly.com/question/17489470

#SPJ11

A 1.78-m3 rigid tank contains steam at 220°C. One-third of the volume is in the liquid phase and the rest is in the vapor form. The properties of steam at 220°C are given as follows: vf = 0.001190 m3/kg and vg = 0.08609 m3/kg.
determine the density

Answers

The tank has a total volume of 1.78 m3, of which one third is in the liquid phase, and the remaining two thirds are in the vapour phase. The system has a density of 287.6 kg/m3.

Describe density.

Density is the measurement of how tightly a substance is packed. It has such definition since it is the mass per unit volume. The density symbol is D, and the density formula is The formula is: = m/V when is the density, m is the object's mass, and V is its volume.

Volume of vapor = (2/3) x 1.78 = 1.1867 m^3

Volume of liquid = (1/3) x 1.78 = 0.5933 m^3

To determine the density, we need to find the mass of the vapor and the mass of the liquid..

Mass of vapor = Volume of vapor / Specific volume of vapor = 1.1867 m^3 / 0.08609 m^3/kg = 13.785 kg

Mass of liquid = Volume of liquid / Specific volume of liquid = 0.5933 m^3 / 0.001190 m^3/kg = 498.3 kg

The total mass of the system is the sum of the mass of the vapor and the mass of the liquid:

Total mass = Mass of vapor + Mass of liquid = 13.785 kg + 498.3 kg = 512.085 kg

Finally, we can calculate the density using the total mass and the total volume of the system:

Density = Total mass / Total volume = 512.085 kg / 1.78 m^3 = 287.6 kg/m^3

To know more about volume visit:-

https://brainly.com/question/22443936

#SPJ1

Consider a 50-cm-diameter and 95-cm-long hot water tank. The tank is placed on the roof of a house. The water inside the tank is heated to 808C by a flat-plate solar collector during the day. The tank is then exposed to windy air at 188 C with an average velocity of 40 km/h during the night. Estimate the temperature of the tank after a 45-min period. Assume the tank surface to be at the same temperature as the water inside, and the heat transfer coefficient on the top and bottom surfaces to be the same as that on the side surface. Evaluate the air properties at 508C

Answers

The temperature of the tank after a 45-min period is estimated to be 30.908 K.

What is temperature?

Temperature is a measure of how hot or cold something is relative to a standard reference point. It is typically measured in degrees Celsius (°C), Kelvin (K), or Fahrenheit (°F).

The rate of heat transfer can be estimated by using the following equation: Q = hA∆T

From the given data, the surface area of the tank is calculated as:

A = πr2 = π (0.25 m)2 = 0.19625 m2

The heat transfer coefficient for a windy environment can be estimated by using the following equation: h = 0.024V1/2, where V is the wind speed (m/s).

From the given data, the wind speed is calculated as: V = 40 km/h = 11.1 m/s

Therefore, the heat transfer coefficient is calculated as: h = 0.024 (11.1)1/2 = 0.92 W/m2K

The temperature difference between the air and the tank is calculated as:  ∆T = (Tair – Ttank) = (288 K – 308 K) = -20 K

Therefore, the rate of heat transfer is calculated as:

Q = hA∆T = (0.92 W/m2K) (0.19625 m2) (-20 K) = -3.7 W

Since the tank is losing heat, the rate of heat transfer is negative.

From the given data, the mass of the water in the tank is calculated as:

m = ρV = (1,000 kg/m3) (0.095 m3) = 95 kg

The specific heat capacity of water is assumed to be 4,186 J/KgK.

Therefore, the temperature difference is calculated as:

∆T = Q/(mc) = (-3.7 W)/ [(95 kg) (4,186 J/KgK)] = -0.0089 K

Therefore, the temperature of the tank after a 45-min period is estimated to be 30.908 K.

To learn more about temperature

https://brainly.com/question/15969718

#SPJ1

Consider the boost converter below. Assume that the inductor is large enough that the current through it is considered constant. + D Vin qt) REV (a) Draw the circuits when the active switch is on and off. Show the direction of the current in each circuit. (b) Ploti, vip, ic and v, for a full period and label their values in terms of given parameters. q(t)t On Off DT T լ։ In terms of I VLT In terms of Vin & V. ipt In terms of I ict In terms of I. & 1. vot In terms of vc

Answers

A boost converter is a type of DC-DC converter that converts a lower input voltage into a higher output voltage. The boost converter shown in the question has an active switch, an inductor, a diode, and a capacitor.

(a) When the active switch is on, the circuit looks like this:

+         +        
Vin  →  SW  →  L  →  D  →  C  →  R  →  -  
        |                             |
        +                             +



The current flows from Vin through the switch, the inductor, the diode, the capacitor, and the resistor, back to Vin. The direction of the current is indicated by the arrows.

When the active switch is off, the circuit looks like this:

+         +        
Vin       SW  →  L  →  D  →  C  →  R  →  -  
        |                             |
        +                             +



The current flows from the inductor through the diode, the capacitor, and the resistor, back to the inductor. The direction of the current is indicated by the arrows.

(b) The plots of i, vip, ic, and v are shown below:

i(t)        vip(t)       ic(t)        v(t)
|           |            |            |
|           |            |            |
|           |            |            |
|           |            |            |
|           |            |            |
|           |            |            |
|           |            |            |
+-----------+------------+------------+------------→ t
0           DT           T            2T



i(t) is the current through the inductor, which is constant and equal to I.

vip(t) is the voltage across the switch, which is equal to Vin when the switch is on and zero when the switch is off.

ic(t) is the current through the capacitor, which is equal to I when the switch is on and zero when the switch is off.

v(t) is the voltage across the resistor, which is equal to Vout when the switch is on and zero when the switch is off.

The values of i(t), vip(t), ic(t), and v(t) are labeled in terms of the given parameters I, Vin, and Vout.

Learn more about the direction of the current :

https://brainly.com/question/15912115

#SPJ11

A cart rolls down a ramp. The cart has a mass of 45 lb m . The cart starts at rest. The ramp is angled 0.17 radians downward from the horizontal. The cart travels a total distance of 97 meters along the ramp on the planet earth. What is the velocity of the cart at the bottom of the ramp? Assume friction is negligible

Answers

To solve this problem, we can use the principle of conservation of energy, which states that the initial potential energy of the system (the cart on the ramp) is converted to kinetic energy at the bottom of the ramp. We can express this as:

mgh = (1/2)mv^2

where m is the mass of the cart, g is the acceleration due to gravity, h is the height of the ramp, and v is the velocity of the cart at the bottom of the ramp.

First, we need to calculate the height of the ramp:

h = dsin(theta) = 97sin(0.17) = 16.16 meters

where d is the total distance traveled along the ramp and theta is the angle of the ramp.

Next, we can plug in the values and solve for v:

459.8116.16 = (1/2)45v^2

v^2 = (459.8116.16)/(1/2*45) = 748.91

v = sqrt(748.91) = 27.37 m/s

Therefore, the velocity of the cart at the bottom of the ramp is 27.37 m/s.

estimate the theoretical fracture strength of a brittle material if it is known that fracture occurs by the propagation of an elliptically shaped surface crack of length 0.29 mm and that has a tip radius of curvature of 0.004 mm when a stress of 1300 mpa is applied.

Answers

The theoretical fracture strength of the brittle material is estimated to be approximately 165.6 MPa when a stress of 1300 MPa is applied and fracture occurs by the propagation of an elliptically shaped surface crack of length 0.29 mm and tip radius of curvature of 0.004 mm.

To estimate the theoretical fracture strength of a brittle material given the information provided, we can use Griffith's theory of brittle fracture. According to this theory, the fracture strength of a brittle material can be expressed as:

σ_f = (2Eγπa)^0.5

where σ_f is the fracture strength, E is the elastic modulus, γ is the surface energy per unit area, and a is the length of the elliptically shaped surface crack.

To calculate the fracture strength, we need to first determine the surface energy per unit area of the material. For glass, a typical value of surface energy is around 1 J/m^2.

Given the length of the elliptically shaped surface crack (a) is 0.29 mm, and the tip radius of curvature is 0.004 mm, we can calculate the crack area (A) as follows:

A = πab = π(0.29/2)(0.004)

A ≈ 5.67 x 10^-7 m^2

Next, we can calculate the elastic modulus (E) of the material. For glass, the elastic modulus is typically around 70 GPa.

Substituting these values into the equation for fracture strength, we get:

σ_f = (2Eγπa)^0.5 = [2(70 x 10^9)(1)(π)(0.29 x 10^-3)]^0.5

σ_f ≈ 165.6 MPa

Learn more about theoretical fracture strength at: https://brainly.com/question/13707729

#SPJ11

A pipe is insulated such that the outer radius of the insulation is less than the critical radius. Now the insulation is taken off. Will the rate of heat transfer from the pipe increase or decrease for the same pipe surface temperature? Explain with the proper formulation or graph.

Answers

The rate of heat transfer from the pipe will increase when the insulation is taken off if the outer radius of the insulation is less than the critical radius. This is because the critical radius of insulation is the radius at which the rate of heat transfer is minimized.

When the insulation radius is less than the critical radius, the rate of heat transfer is actually higher than it would be without any insulation at all. Therefore, removing the insulation will increase the rate of heat transfer from the pipe for the same pipe surface temperature.

The critical radius of insulation can be calculated using the following formula:

[tex]r_c = k/h[/tex]

Where [tex]r_c[/tex] is the critical radius of insulation, k is the thermal conductivity of the insulation, and h is the heat transfer coefficient of the fluid surrounding the pipe. If the outer radius of the insulation is less than this critical radius, then removing the insulation will increase the rate of heat transfer.

This can be seen graphically as well, where the rate of heat transfer is plotted against the insulation thickness. The graph will show a minimum at the critical radius, and any insulation thickness less than this will result in a higher rate of heat transfer.

Learn more about insulation

https://brainly.com/question/18598066

#SPJ11

Need help with question

Answers

Answer:    

Explanation:

     

two technicians are discussing the use of a dmm. technician a states that back-probing is a technique used to reduce the chance of damage while measuring. technician b states that insulation piercing probes do not increase the hcance of corrosion or damage to the conductor

Answers

Both technicians are correct in their statements about the use of a digital multimeter (DMM).

Technician A is correct in stating that back-probing is a technique used to reduce the chance of damage while measuring. This is because back-probing allows for the measurement of electrical signals without having to disconnect or damage the wires or connectors. It is a non-invasive method of measurement that reduces the risk of damage to the circuit or components.

Technician B is also correct in stating that insulation piercing probes do not increase the chance of corrosion or damage to the conductor. This is because these probes are designed to pierce the insulation of a wire without causing damage to the conductor inside. They allow for the measurement of electrical signals without having to strip the insulation, which can reduce the risk of corrosion or damage to the conductor.

Overall, both technicians are correct in their statements about the use of a DMM and the techniques used to reduce the chance of damage while measuring electrical signals.

You can learn more about digital multimeter (DMM) at

https://brainly.com/question/29737388

#SPJ11

Automotive electric motors use AC current.
O True
O False

Answers

True, automotive applications use both AC and DC (direct current) motors. Nonetheless, AC motors are the type of electric motors seen in current electric and hybrid vehicles the most frequently.

AC current is it used in automotive motors?

While the motor of your electric vehicle runs on AC, the battery requires DC power. Hence, an onboard or external conversion from alternate to direct current is necessary. Grid electricity is always AC.

Which motors utilize current?

Direct current (DC) and alternating current (AC) both have advantages and disadvantages when used to power motors. In order to assess a DC motor for the purposes of this essay, visit here to read about AC motors. A DC motor's essential components include: Stator.

To know more about electric motors visit:-

https://brainly.com/question/21127297

#SPJ1

A thin plate . moves between two parallel, horizontal, stationary flat surfaces at a constant
velocity of V m/s. The two stationary surfaces are spaced 8 cm apart, and the medium between
them is filled with oil whose viscosity is 0.9 Ns/m2
. The part of the plate immersed in oil at
any given time is 2-m long and 0.5-m wide. If the plate moves through the mid-plane between
the surfaces, determine the force required to maintain this motion.. ρwater=1000 kg/m3
. g=9.81
m/s2
v=10.5 m/s
.

Answers

The magnitude of shear forces acting on as mentioned in the above case will be 600N .

What is shear force?

Shear force is defined as the force acting on a material in a direction opposite to its extension and parallel to a body's planar cross section.

a) The magnitude of shear forces acting on the upper and lower surfaces of the plate are:

                                           F(shear,upper)=τ(w,u)As

                                    F(shear,upper)=μAs[tex]mod[/tex](du/dy)

                                       F(shear,upper)=μAs (V-0)/h1     (V=5)

                                                 =(0.9)(2×0.5)(5-0)/10⁻²

                                                  =450N

     similarly,

                                  F(shear,lower)=μAs (V-0)/h2

                                                      =(0.9)(2×0.5)(5-0)/3×10⁻²

                                                         =150N

      Totally,       F=F(shear,upper)+F(shear,lower)

                            =450N+150N

                             =600N

To know more about shear force visit:

https://brainly.com/question/30216353

#SPJ9

which of the following requires an endorsement on your cdl ​

Answers

Answer:

Explanation:

Determine the change of volume caused in the block due to the application of the forces (Bulk
Modulus Problem). Set E=60 GPa, poisson Ratio v=0.25, assume isotropic material

Answers

The block has shrunk by about 45.3% based on the volume change, which is -0.453 times the initial volume.

The bulk modulus is negative, why?

The expression's negative sign indicates how the excessive pressure applied caused the material's volume to shrink. In other words, a decrease in volume will result from an increase in pressure. The volume change will be negative if pressure P is positive.

ΔV/V = -3K ΔP

K = E/(3(1-2v))

Given:

[tex]E = 60 GPa = 60 x 10^9 Pa[/tex]

v = 0.25

a = 100 mm = 0.1 m

b = 50 mm = 0.05 m

c = 60 mm = 0.06 m

F1 = 1801 N

F2 = 50 kN = 50000 N

F3 = 100 kN = 100000 NF_total = F1 + F2 + F3

F_total = 1801 N + 50000 N + 100000 N

F_total = 151801 NΔP = F_total / (abc)

ΔP = 151801 N / (0.1 m x 0.05 m x 0.06 m)

[tex]ΔP = 5.0337 x 10^7 Pa[/tex]

Finally, we can calculate the fractional change in volume using the formula:

ΔV/V = -3K ΔP

[tex]K = E/(3(1-2v)) = 60 x 10^9 Pa / (3(1-2(0.25))) = 6.0 x 10^10 Pa[/tex]

[tex]ΔV/V = -3(6.0 x 10^10 Pa) (5.0337 x 10^7 Pa)[/tex]

ΔV/V = -0.453

To know more about volume visit:-

https://brainly.com/question/22443936

#SPJ1

Other Questions
When a flower is placed in water, how do the nutrients in the water travel to the other parts of the plant?The plant absorbs the nutrients through the sunlight. Flowers are nonvascular, so nutrients do not need to travel. The nutrients move from cell to cell up to the other parts of the flower. The nutrients travel to the other parts of the flower through the tubes of the vascular system Please help I need all these answer by tonight The following events occur for The Turner Corporation during 2024 and 2025, its first two years of operations. June 12, 2024 Provide services to customers on account for $35,000. September 17, 2024 Receive $20,000 from customers on account. December 31, 2024 Estimate that 40% of accounts receivable at the end of the year will not be received. March 4, 2025 Provide services to customers on account for $50,000. May 20, 2025 Receive $10,000 from customers for services provided in 2024. July 2, 2025 Write off the remaining amounts owed from services provided in 2024. October 19, 2025 Receive $40,000 from customers for services provided in 2025. December 31, 2025 Estimate that 40% of accounts receivable at the end of the year will not be received. Required: 1. Record transactions for each date. 2. Post transactions to the following accounts: Cash, Accounts Receivable, and Allowance for Uncollectible Accounts. 3. Calculate net accounts receivable reported in the balance sheet at the end of 2024 and 2025 How to calculate July 2, 2025 Write off the remaining amounts owed from services provided in 2024. In triangle ABC, the length of side AB is 16 inches and the length of side BC is 25 inches. Which of the following could be the lengthof side AC?A. 29 inchesB. 46 inchesC. 43 inchesD. 7 inches HelloGoodbyeYou created the above table but you decided that you don't want the text in the middleof the cell, instead you would rather it be centered but at the top of the cell. Whatsetting in Table Properties would allow you to do this?O Cell vertical alignmentO Cell paddingO Cell phoneCell horizontal alignment on Question 1.Let's say you were to roll two dice 1000 times. What is thenumber of times you would expect the number 7 to appear? How much larger is the pizza made in a circular pan with 14 inch diameter than a pizza made in square pan with sides measuring 14 inches Read the following sentence:I vacuum every day because two cats and a dog_______a lot of fur!Choose the word that makes the sentence coherent.O shedsO sheddedOshedO shedding Fact: the region under the standard normal curve that lies to the left of,-1.34 has area 0.0901227.Without consulting a table or a calculator giving areas under the standard normal curve, determine the area under the standard normal curve that lies to the right of 1.34.answer:b) Which property of the standard normal curve allowed you to answer part a)?A. The total area under the curve is 1B. The standard normal curve is symmetric about 0C. The standard normal curve extends indefinitely in both directionsD. Almost all the area under the standard normal curve lies between -3 and 3E. None of the above Peggy (from the preceding exercise) reviews the sales and variance information from her first six months of the year to forecast her revenues for the last six months of the year. She decides to forecast a sales increase of 4. 75 percent to predict her upcoming changes in sales. Help her calculate the projected sales and revenue forecasts for the last six months of the year. Projected Sales Revenue Increase Forecast Month July August September October November December 6-Month Total Predicted Sales Last Year Change $36,587. 91 4. 75% 36,989. 73 4. 75% 40,896. 32 4. 75% 37,858. 63 4. 75% 37,122. 45 4. 75% 37,188. 71 4. 75% Father's age is five times than the son's age. If the sum of their age is 60 years, find their present ages.Please solve this with step by step. 10. Rosa is calculating the measure of an interiorangle of a regular polygon with 22 sides.Which expressions can she use to find theangle measure? Select all that apply.(20 180) , 22(24 180) , 22(20 180) , 20[(22 + 2) 180] , 22[(22 - 2) 180] , 22 You are an audit senior for EY and have just been assigned to the audit of Rouge Valley Golf and Health Club (RVGH). The partner provided you with the following information.RVGH is a public company that operates eight clubs in a large city and offers one-year memberships. Membership gives members access to golf and the fitness centre including fitness classes. The members may use any of the eight facilities but must reserve golf time and pay a separate fee before using one of the golf courses. As an incentive, RVGH advertised that any customers who are not satisfied for any reason can receive a refund of the remaining portion of their unused membership fees. Membership fees are recognized as revenue when received. Membership fees are due at the beginning of the individual membership period; however, customers have the option of financing the membership fee over the membership period at an interest rate of 8%.In the past, some customers have said they would like to take only the regularly scheduled aerobic classes and not pay for the full membership. During the current fiscal year, RVGH began selling coupon books for only aerobic classes to accommodate these customers. Each book is dated and contains 50 coupons that may be redeemed for any regularly scheduled aerobics class over a one-year period. After the one-year period, unused coupons are no longer valid.RVGH recognizes the revenue from the coupon books when the books are sold.During 2020, RVGH expanded into the health equipment market by purchasing a local company that manufactures elliptical machines. These machines are used in RVGH's facilities and are sold through the clubs and catalogues. Customers must make a 20% down payment when placing an equipment order. RVGH recognizes the down payment as revenue when received. Delivery is in 60 to 90 days after an order is placed. The machines are sold with a one-year unconditional guarantee against defaults. Based on experience, RVGH expects the costs of repairing machines under guarantee to be 4% of sales.RVGH is preparing financial statements as at May 1, 2022, the end of its fiscal year. Jaymie Hogan, corporate controller, receives a bonus based on the net income. The bank is waiting for the preliminary financial statements in consideration of new debt requested by RVGH.InstructionsThe partner has asked that you write a report in case format in which you identify the financial reporting issues related to RVGH. Further, you are required to analyze the criteria for each issue applying the case facts and include consideration of any impact on the financial statement and users. Given,TPL=f(l,k), prove that,MPL and APL are equal at apoint where APL is at its maximum Matilda wants to buy some high-quality olive oil. She can buy 2 L bottle for $50, or she can buy 175 mL bottle for $5. In order to compare the prices, she needs to convert the volume of the second bottle to liters. How many liters of olive oil are in the smaller bottle?A. 1.75 LB. 0.175 L C. 175 L D. 17.5 L The Evanec Company's next expected dividend, D1, is $3.18; its growth rate is 6%, and its common stock now sells for $36.00. New stock (external equity) can be sold to net $32.40 per share.a) What is Evanec's cost of retained earning, rs ?b) What is Evanec's percentage flotation cost, F ?c) What is Evanec's cost of new common stock, re ? point z is the circumcenter of triangle tub what is the value of uv whoch organelle is denoted by a? A local mechanic uses the following linear equation to model his charges y=30x+50, where the charges (y) is a function of the number of hours (x) worked. What is the coefficient in this equation and what does it mean? Need more assistance on this, please help