a. You have been newly recruited by an optical fibre company that specialises in optical fibre design. Your first assignment is to characterise a batch of newly fabricated multimode fibre that would be deployed in an in-building network. Based on the specifications of the fibre, you know that the multi-mode fibre has a core with a refractive index of 1.45 and a profile height of 1.5%. i. What is the bit-rate-distance product of this fibre? (2 marks) ii. As this fibre will be used for in-building application, determine the maximum transmission distance if the fibre is expected to support a 500 Mb/s link. (2 marks) iii. While submitting your report to the deployment team, you found out that this fibre will be deployed in a high-rise building with potential deployment length of 100 m. With this limitation placed on the fibre distance, what is the maximum bit-rate that the link can handle in this deployment? (2 marks) iv. After notifying the deployment team that the initial 500 Mb/s specification cannot be met if the transmission distance is extended to 100m, the deployment team suggested to use dispersion compensating scheme such as dispersion compensating fibre to improve the transmission bit-rate. Explain whether this can be done and why. (2 marks) b. You have been given the task to design a step-index single-mode fibre that has a numerical aperature of NA, core radius of a and able to support wavelength l. i Show that the following equation holds if the fibre is to only support one mode. (1 marks) � � < 2.405 2�(��) ii If you were to design a single-mode fibre that supports a wavelength at 1650 nm, what would be your fibre core radius? Assuming core and cladding refractive indices are given as 1.505 and 1.49 respectively. (2 marks) iii Can your designed fibre support light at 2000 nm in a single mode format? (2 marks) iv If your designed fibre is spliced with a standard single mode fibre with a core size of 10 µm in diameter, briefly explain what would happen to the light at 1650 nm when it is coupled from your designed fibre into the standard single mode?
Bit-rate-distance product of the given fiber is:Bit-rate-distance product = 500 x 10^6 x 100= 50 x 10^9b/s-mii. Maximum transmission distance can be found using the formula:
Bit-rate-distance product = (1.44 x 10^-3)/2 x (distance) x log2(1 + (Pavg x 10^3)/(0.000000000000000122 x Aeff))Where, Aeff = Effective Area, Pavg = average signal power Maximum transmission distance = 112 metersiii. As per the given problem, the length of the optical fiber is 100 meters.
Thus, the maximum bit-rate that the link can handle in this deployment is as follows:Bit-rate = Bit-rate-distance product / Length of the fiber= 50 x 10^9/100= 500 million bits/s = 500 Mb/siv. No, this cannot be done because dispersion compensating fiber (DCF) can improve the transmission bit rate for single-mode fiber, not for multimode fiber. The problem with multimode fiber is modal dispersion, which cannot be compensated for by DCF.
To know more about Bit-rate-distance visit:
https://brainly.com/question/30591874
#SPJ11
A shaft is loaded in bending and torsion such that Ma=70 Nm, Ta= 45 Nm, Mm= 55 Nm, and T= 35 Nm. For the shaft, Su = 700 MPa and Sy = 560 MPa, and a fully corrected endurance limit of Se=210 MPa is assumed. Let Kf=2.2 and Kfs=1.8. With a design factor of 2.0 determine the minimum acceptable diameter of the shaft using the: (a) DE-Gerber criterion. (b) DE-ASME Elliptic criterion. (c) DE-Soderberg criterion. (d) DE-Goodman criterion.
When a shaft is loaded in both bending and torsion, then it is called a combined load.Therefore, the minimum acceptable diameter of the shaft is as follows:(a) DE-Gerber criterion = 26.4 mm(b) DE-ASME Elliptic criterion = 34 mm(c) DE-Soderberg criterion = 27.5 mm(d) DE-Goodman criterion = 22.6 mm.
Here, Ma= 70 Nm,
Ta= 45 Nm, Su = 700 MPa,
Sy = 560 MPa,
Kf=2.2
and Kfs=1.8,
and the fully corrected endurance limit of Se=210 MPa is assumed.
Solving for the above formula we get: \[d > 0.0275 \,\,m = 27.5 \,\,mm\](d) DE-Goodman criterion.Goodman criterion is used for failure analysis of both ductile and brittle materials.
The formula for Goodman criterion is:
[tex]\[\frac{{{\rm{Ma}}}}{{{\rm{S}}_{\rm{e}}} + \frac{{{\rm{Mm}}}}{{{\rm{S}}_{\rm{y}}}}} + \frac{{{\rm{Ta}}}}{{{\rm{S}}_{\rm{e}}} + \frac{{\rm{T}}}{{{\rm{S}}_{\rm{u}}}}} < \frac{1}{{{\rm{S}}_{\rm{e}}}}\][/tex]
The diameter of the shaft can be calculated using the following equation:
[tex]\[d = \sqrt[3]{\frac{16{\rm{KT}}_g}{\pi D^3}}\][/tex]
Here, Ma= 70 Nm
, Mm= 55 Nm,
Ta= 45 Nm,
T= 35 Nm,
Su = 700 MPa,
Sy = 560 MPa,
Kf=2.2 and
Kfs=1.8,
and the fully corrected endurance limit of Se=210 MPa is assumed.
Solving for the above formula we get:
[tex]\[d > 0.0226 \,\,m = 22.6 \,\,mm\][/tex]
To know more about diameter visit:
https://brainly.com/question/32968193
#SPJ11
A 0.02 m³ tank contains 1.6 kg of argon gas at a temperature of 110 K. Using the van de Waal's equation, what is the pressure inside the tank? Express your answer in kPa.
The pressure inside the tank is approximately 28.63 kPa by using van der Waal's equation.
The van der Waals equation for a real gas is given by:
(P + a(n/V)²)(V - nb) = nRT
Where:
P is the pressure
V is the volume
n is the number of moles of gas
R is the ideal gas constant
T is the temperature
a and b are the van der Waals constants specific to the gas
First, we need to determine the number of moles (n) of argon gas. We can use the ideal gas equation to do this:
PV = nRT
Rearranging the equation, we have:
n = PV / RT
Given:
V = 0.02 m³
T = 110 K
m (mass of argon) = 1.6 kg
molar mass of argon = 39.95 g/mol
First, we convert the mass of argon to moles:
n = (1.6 kg / 39.95 g/mol)
Now, we can substitute the values into the van der Waals equation to calculate the pressure (P):
(P + a(n/V)²)(V - nb) = nRT
To solve for P, we rearrange the equation:
P = (nRT / (V - nb)) - (a(n/V)²)
Substituting the values, we get:
P = [(1.6 kg / 39.95 g/mol) * (8.314 J/(molK)) * (110 K)] / (0.02 m³ - 0.0266 m³/mol * (1.6 kg / 39.95 g/mol)) - (1.355 Jm³/(mol²))
Calculating this expression gives us:
P ≈ 28627.89 Pa
Converting Pa to kPa:
P ≈ 28.63 kPa
To know more about pressure visit
https://brainly.com/question/30638002
#SPJ11
Briefly describe the difference between a constant strain and linear strain triangular finite element. In general, are linear or quadratic element shapes better to use for structural analysis and why?
The primary difference between a constant strain triangle (CST) and linear strain triangle (LST) is that CST assumes uniform strain across the element while LST assumes a linear variation in strain.
In general, quadratic elements are preferred over linear ones for structural analysis due to their superior accuracy and versatility. Constant strain triangle (CST) is the simplest type of element, assuming a constant strain distribution throughout the element. This leads to less accurate results in complex problems. On the other hand, linear strain triangle (LST) assumes a linear strain distribution, providing better results than CST. Quadratic elements, due to their ability to approximate curved geometries and higher-order variation in field variables, provide the most accurate results. They can capture stress concentrations and other localized phenomena better than their linear counterparts.
Learn more about finite element analysis here:
https://brainly.com/question/13088387
#SPJ11
Mark the correct answers / statements with a cross, or define the correct answers / statements, e.g. mentioning a.1). For each correct cross / definition you will receive 1.5 points, each cross which is not correct will subtract 1.5 points from the total score. The total score for the entire question cannot be negative.
a) A system with PT2-characteristic has a damping ratio D = 0.3.
O a.1) The system is critically damped. O a.2) The system is always stable.
O a.3) The system has two zeros.
O a.4) The imaginary part of the poles are nonzero.
The total score for the entire question cannot be negative. So the correct answers are a.1) The system is critically damped.a.2) The system is always stable.a.3) The system has two poles.a.4) The imaginary part of the poles is nonzero.
a) A system with PT2-characteristic has a damping ratio D = 0.3.
O a.1) The system is critically damped.
O a.2) The system is always stable.
O a.3) The system has two zeros.
O a.4) The imaginary part of the poles is nonzero.
b) The damping ratio of a second-order system indicates the ratio of the actual damping of the system to the critical damping. The values range between zero and one. Based on the given damping ratio of 0.3, the following is the correct answer:
a.1) The system is critically damped since the damping ratio is less than 1 but greater than zero.
a.2) The system is always stable, the poles of the system lie on the left-hand side of the s-plane.
a.3) The system has two poles, not two zeros.
a.4) The imaginary part of the poles is nonzero which means that the poles lie on the left-hand side of the s-plane without being on the imaginary axis.
To know more about critically damped please refer to:
https://brainly.com/question/13161950
#SPJ11
Square loop with sides a and wire radius b: LA = 2μo a/π=[In (a/b) - 0.774]
A square loop with sides a and wire radius b: LA = 2μo a/π=[In (a/b) - 0.774]The given equation states that the inductance of a square loop of sides a and wire radius b can be determined as LA = 2μo a/π=[In (a/b) - 0.774].
Here, 'a' and 'b' represent the sides and the wire radius of the square loop respectively. LA represents the inductance of the square loop.The above formula can be used to calculate the inductance of a square loop. We can use this formula to find the value of the inductance of a square loop of given dimensions.Let's understand the concept of inductance before diving into the calculation of the formula.What is Inductance?Inductance is defined as the ability of a component to store energy in a magnetic field
.Inductance is the resistance of an electrical conductor to a change in the flow of electric current. It is the property of a conductor that opposes any change in the current flowing through it. The larger the inductance of a conductor, the more energy it can store in a magnetic field created by an electric current flowing through it.The inductance of a square loop of sides 'a' and wire radius 'b' can be determined using the given formula LA = 2μo a/π=[In (a/b) - 0.774].
To know more about radius visit:
https://brainly.com/question/13449316
#SPJ11
Why does the alloy system incorporate the solute solvent
relation?
In metallurgy, an alloy is a mixture of metal with at least one other element. This blending is done to modify the properties of the metal in some way. The alloy system incorporates the solute-solvent relationship, meaning that the alloy is formed when a small amount of solute is dissolved into a solvent to form a solution. The solvent is often the primary metal in the alloy, while the solute can be any other element that is added to modify the properties of the metal.
Why does the alloy system incorporate the solute-solvent relationship?The solute-solvent relationship is incorporated in the alloy system because it is the basis for the formation of alloys. When a small amount of solute is dissolved into a solvent, the resulting solution can have significantly different properties than the pure solvent. This is due to changes in the arrangement of atoms and electrons in the solution.
Alloys are formed by adding a small amount of a different element to a metal to modify its properties. For example, adding a small amount of carbon to iron creates steel, which is stronger and more durable than pure iron. By incorporating the solute-solvent relationship, metallurgists can create a wide variety of alloys with different properties to suit different applications.
To know more about mixture visit:-
https://brainly.com/question/12160179
#SPJ11
Consider an FSM that has a 1-bit input A and a 1-bit
output F (found). Design a Moore FSM that repeatedly detects the serial input: 10110.
When that input is detected, the output F should assert for one clock cycle. So, A changes
over time – it is a serial input, because a new bit appears on that signal each clock cycle.
(a) Sketch the state transition diagram.
(b) Implement the FSM in SystemVerilog. Name the module: seqdetector.
Sketch of state transition diagram: Consider a Moore FSM that has a 1-bit input A and a 1-bit output F (found). Design a Moore FSM that repeatedly detects the serial input: 10110. When that input is detected, the output F should assert for one clock cycle.
The module has two ports, an input port a and an output port f. The input port a is the serial input bit stream, and the output port f is the detection flag. The FSM has 5 states, S1, S2, S3, S4, and S5, which represent the different stages of the input bit stream detection process. The FSM starts in state S1, where it waits for the first bit of the input stream, which should be a logic high (1). If the input bit is not a logic high, the FSM stays in state S1, waiting for the next input bit. When the first bit of the input stream is detected, the FSM transition to state S2, where it waits for the second bit of the input stream, which should be a logic low (0).
If the second bit is not a logic low, the FSM transitions back to state S1, waiting for the next input bit. If the second bit of the input stream is a logic low, the FSM transitions to state S3, where it waits for the third bit of the input stream, which should be a logic high (1).
To know more about state transition diagram visit:
https://brainly.com/question/13263832
#SPJ11
Question 1: Design a linkage system such that as a float for liquid level measurement moves from 0 to 1 m, an LVDT core moves over its linear range of 3 cm. Question 2: A pressure transducer outputs a voltage to a readout device that converts the signal back to pressure: The device specifications are: Resolution: 0.1 psi Sensitivity error: 0.1 psi Linearity error: within 0.1% of reading Drift: less than 0.1 psi/6 months (32-90F) The transducer has a claimed accuracy of within 0.5% of reading. For a nominal pressure of 100 psi at 70F, estimate the design-stage uncertainty in a measured pressure.
When a float is present for the measurement of liquid level moving from 0 to 1 m, the LVDT core moves over its linear range of 3 cm. The float will be attached to the end of the linkage system so that the float moves from 0 to 1 m, and the LVDT core moves over its linear range of 3 cm.
The system will be designed in such a way that the float moves in a linear manner from 0 to 1 m. The linkage system is shown below: Let the float be situated at the beginning of the linkage system and the LVDT core be located at the end of the linkage system.
The length of the linkage system is defined by the float movement range (0-1 m). We must adjust the lengths of the links to achieve a LVDT core movement range of 3 cm. The float will be attached to the first link of the linkage system, which will be a straight link, as shown in the figure above.
To know more about measurement visit:
https://brainly.com/question/28913275
#SPJ11
Question 3 DC Engineering Company has two units operating in two different cities A and B, where the manufacturing of engineering components takes place. Both the units employ young graduates as well as mid-career engineers. The company pays attractive salary to recruit competent workforce. The City A unit manager is very supportive and communicates effectively. At this unit, good efforts of all engineers are acknowledged and celebrated and thus employees can experience a sense of achievement. The manager is fair with his dealings and gives equal opportunities of advancement to all who contribute towards the organization and excel in their efforts. Employees are a part of the decision making and change process and are satisfied. The unit seldom experiences absenteeism or employee turnover. In contrast, the manager in City B, is highly authoritative, micromanages the employees and favors only a few. Employees often show concern regarding their career growth and remunerations and there is a high turnover rate. Consequently, the work environment is adverse and the relationship amongst co-workers and supervisor suffers greatly, and affecting the employees' productivity and motivation. (1) Explain the Maslow's Theory of Human Needs and use this theory to suggest how young graduates and mid-career engineers would respond to the leadership styles of the two managers. (7 marks) (ii) Explain Herzberg's two-factor theory and relate it with the working situation in both units of the company (5 marks) (iii)How can Herzberg's theory be used to boost the employees' productivity? (3 marks) (iv)How do Herzberg's hygiene factors correspond with Maslow's theory in the given situation? (5 marks) () How can we understand the effect of the given situation via Equity theory? (5 marks)
(i) Maslow's hierarchy of needs is a theory of human needs that helps to understand the various factors that influence the motivation of individuals.
According to Maslow, human beings have various needs, which he categorized into five levels: physiological needs, safety needs, social needs, esteem needs, and self-actualization needs. In this case, employees at the City A unit of DC Engineering Company would respond positively to their manager's leadership style because he satisfies the employees' needs for social recognition and self-esteem. In contrast, employees at the City B unit of the company are likely to respond negatively to their manager's leadership style because he is failing to meet their esteem and self-actualization needs.
(ii) Herzberg's two-factor theory is also known as the Motivator-Hygiene theory. Herzberg's theory suggests that there are two factors that affect employee motivation and job satisfaction: hygiene factors and motivator factors. Hygiene factors include working conditions, salary, job security, and company policies. Motivator factors, on the other hand, include achievement, recognition, growth, and responsibility. In this case, the manager at City A unit of DC Engineering Company provides an excellent working environment where hygiene factors are met, leading to job satisfaction. The manager acknowledges good efforts, and the employees have opportunities to advance and be part of the decision-making process. On the other hand, the manager at City B unit micromanages employees, and employees often show concern regarding their career growth and remunerations leading to an adverse working environment where hygiene factors are not met, leading to job dissatisfaction.
(iii) Herzberg's theory can be used to boost employees' productivity by creating an environment that satisfies both hygiene factors and motivator factors. Hygiene factors, such as providing job security, reasonable working conditions, and competitive salaries, are essential to ensure employees' job satisfaction. Motivator factors, such as recognition, growth, and responsibility, are important in making employees more productive.
(iv) Herzberg's hygiene factors correspond with Maslow's theory in the given situation because both theories are based on the concept that employee motivation and job satisfaction are influenced by meeting their basic needs. Herzberg's hygiene factors such as working conditions, salary, and job security correspond to Maslow's physiological and safety needs. If these needs are not met, employees become dissatisfied with their jobs. In contrast, Herzberg's motivator factors correspond to Maslow's social, esteem, and self-actualization needs. If these needs are met, employees become motivated and productive.
(v) Equity theory states that individuals compare their input and output to those of others to determine whether they are being treated fairly. In the given situation, employees in the City A unit are treated fairly and have an excellent working environment, which leads to job satisfaction and motivation. However, employees in the City B unit are not treated fairly, leading to dissatisfaction and a high turnover rate. Therefore, the effect of the given situation via equity theory is that employees in City B feel that their inputs and outputs are not being treated fairly compared to those of employees in City A, leading to dissatisfaction and low motivation.
To know more about Maslow's theory, visit:
https://brainly.com/question/33539726
#SPJ11
Find the production cost per 1000 kg steam in a steam plant when the evaporation rate is
7.2 kg steam per kg coal; initial cost of plant, $150,000; annual operational cost exclusive
of coal, $15,000. Assume life of 20 years; no final value; interest on borrowed capital, 4%;
on sinking fund, 3%. Average steam production is 14,500 kg per hr; cost of coal, $8.00 per
ton.
The production cost per 1000 kg steam in a steam plant when the evaporation rate is 7.2 kg steam per kg coal is $18.03. This is obtained as follows;
Step-by-step explanation:
The steam produced from the combustion of coal in a steam plant can be evaluated by first finding the amount of steam generated per kg of coal burned. This is called the evaporation rate.The evaporation rate is given as 7.2 kg steam per kg coal.The cost of coal is given as $8.00 per ton.The steam plant has an average steam production of 14,500 kg per hr.Annual operational cost exclusive of coal is $15,000.The initial cost of plant is $150,000.The life of the steam plant is 20 years.
The interest on borrowed capital is 4% while the interest on the sinking fund is 3%.To find the cost of steam production per 1000 kg, the following calculations are made;
Total amount of steam produced in one year = 14,500 * 24 * 365 = 126,540,000 kg
Annual coal consumption = 126,540,000 / 7.2 = 17,541,666.67 kg
Total cost of coal in one year = (17,541,666.67 / 1000) * $8.00 = $140,333.33
Total cost of operation per year = $140,333.33 + $15,000 = $155,333.33
Annual equivalent charge = AEC = 1 + i/n - 1/(1+i/n)^n*t
Where i = interest n = number of years for which the sum is invest
dt = total life of the investment AEC = 1 + 0.04/1 - 1/(1+0.04/1)^(1*20) = 1.7487
Annual equivalent disbursement = AED = S / a
Where S = initial cost of plant + sum of annual cost (AEC) for n y
earsa = annuity factor obtained from the tables
.AED = $150,000 / 3.8879 = $38,595.69
Annual sinking fund = AS = AED * i / (1 - 1/(1+i/n)^n*t)AS = $38,595.69 * 0.03 / (1 - 1/(1+0.03/1)^(1*20)) = $1,596.51
Total annual cost of the steam plant
= $155,333.33 + $1,596.51
= $156,929.84
Cost of steam production per 1000 kg = 1000 / (126,540,000 / 14,500) * $156,929.84 = $18.03Therefore, the cost of steam production per 1000 kg is $18.03.
To know more about evaporation visit :
https://brainly.com/question/28319650
#SPJ11
A tank with an inlet and an outlet initially contains 200 gal of water in which 40 lb of salt are dissolved. Then five gal of brine, each containing 10 lb of dissolved salt, run into the tank per minute through the inlet, and the mixture, kept uniform by stirring, runs out of the tank through the outlet at the same rate. (a) Find the amount of salt y(t) in the tank at any time t. (b) Find the limit of the salt in the tank.
The amount of salt in the tank at any time t is y(t) = 2000 - 50 e^(-t/40), the limit of the salt in the tank is 2000 pounds.
(a) The amount of salt y(t) in the tank at any time t:Initially, the tank contains 200 gallons of water with 40 pounds of salt. As brine is entering at a rate of 5 gallons per minute, then the amount of salt in this brine is 10 pounds per gallon. Let x(t) denote the number of gallons of brine that has entered the tank. Then, at any time t, the amount of salt in the tank is y(t).Thus, the differential equation of the amount of salt in the tank over time can be derived as:dy/dt = (10 lb/gal)(5 gal/min) - y/200 (5 gal/min)dy/dt = 50 - y/40
Rearranging the differential equation: dy/dt + y/40 = 50. The integrating factor is: e^(∫1/40dt) = e^(t/40)Multiplying both sides by the integrating factor: e^(t/40) dy/dt + (1/40) e^(t/40) y = (50/1) e^(t/40)Simplifying the left-hand side: (e^(t/40) y)' = (50/1) e^(t/40)Integrating both sides: e^(t/40) y = (50/1) ∫e^(t/40)dt + C, where C is the constant of integration.Rewriting the equation: y = 2000 - 50 e^(-t/40)
(b) The limit of the salt in the tank:The limit of y(t) as t approaches infinity can be found by taking the limit as t approaches infinity of the expression 2000 - 50 e^(-t/40).As e^(-t/40) approaches 0 as t approaches infinity, the limit of y(t) is 2000.
To know more about stirring visit :
https://brainly.com/question/31406450
#SPJ11
For the following iron-carbon alloys (0.76 wt%C) and associated microstructures
A. coarse pearlite B. spheroidite C. fine pearlite D. bainite E. martensite F. tempered martensite 1. Select the most ductile 2. Select the hardest 3. Select the one with the best combination of strength and ductility.
For the following iron-carbon alloys (0.76 wt%C) and associated microstructures:A. coarse pearlite B. spheroidite C. fine pearlite D. bainite E. martensite F. tempered martensite1. Select the most ductileWhen the alloy has a coarse pearlite structure, it is the most ductile.2. Select the hardestWhen the alloy has a martensite structure, it is the hardest.
3. Select the one with the best combination of strength and ductilityWhen the alloy has a fine pearlite structure, it has the best combination of strength and ductility.Explanation:Pearlite: it is the most basic form of steel microstructure that consists of alternating layers of alpha-ferrite and cementite, in which cementite exists in lamellar form.Bainite: Bainite microstructure is a transitional phase between austenite and pearlite.Spheroidite: It is formed by further heat treating pearlite or tempered martensite at a temperature just below the eutectoid temperature.
This leads to the development of roughly spherical cementite particles within a ferrite matrix.Martensite: A solid solution of carbon in iron that is metastable and supersaturated at room temperature. Martensite is created when austenite is quenched rapidly.Tempered martensite: Tempered martensite is martensite that has been subjected to a tempering process.
To know more about martensite visit :
https://brainly.com/question/31414307
#SPJ11
our practical report must have an introduction where you will introduce your experiments topics and it need to be divided into 3 paragraphs,
1. Paragraph one, give a brieve definition of your topics 2. Paragraph two, give a brieve history on motor failure analyses and link it to todays applications and methods used in this day and age. 3. Paragraph three, introduce your work, (Name the paragraph the: AIM) by stating what is required from you on this assignment. [THIS IS A VERY IMPORTANT PARAGRAPH] [This paragraph and your conclusion must relate to each other]
When writing a practical report, you will need to have an introduction where you introduce your experimental topics and it should be divided into 3 paragraphs.
The following is an outline of how the introduction should be structured:
This paragraph should give a brief definition of your topics. Here, you should explain what your experimental topics are and why they are important. It is important to be clear and concise in this paragraph. This paragraph should provide a brief history of motor failure analyses and link it to today's applications and methods used in this day and age.
Here, you should explain how motor failure analyses have evolved over time and how they are used today. You should also discuss the methods used in this day and age and how they are different from the methods used in the past. This paragraph should introduce your work and state what is required from you on this assignment. You should name the paragraph the AIM.
To know more about practical visit:
https://brainly.com/question/32439310
#SPJ11
You run a corrosion test and determine that after 48 hours a Cobalt block lost 45 grams of material due to oxidation. What was the current flow (in amps) during the corrosion process? a 0.243 amps b 0.853 amps c 0.426 amps d 3.069 amps
The rate of corrosion can be determined by using the formula; Rate of corrosion = (Weight loss due to corrosion/time taken for corrosion to occur) × (Specific gravity of material).
Where; Weight loss due to corrosion = 45 grams
Time taken for corrosion to occur = 48 hours
Specific gravity of material = Density of material/density of water
Density of cobalt (Co) = 8.9 g/cm³Density of water = 1 g/cm³
Density of Co/Density of water = 8.9/1 = 8.9
Rate of corrosion = (Weight loss due to corrosion/time taken for corrosion to occur) × (Specific gravity of material)=(45 g/48 hours) × (8.9)= 0.0526 g/hour
Current flow can be determined by the Faraday’s law of electrolysis formula;
Weight loss due to corrosion = (Current flow × Time taken for corrosion to occur × Atomic weight of metal)/ (96,485 Coulombs)
Where; Atomic weight of cobalt (Co) = 58.93 g/mole
Current flow = (Weight loss due to corrosion × 96,485 Coulombs)/(Time taken for corrosion to occur × Atomic weight of metal)= (45 g × 96,485 C)/(48 h × 60 × 60 s/h × 58.93 g/mole)= 0.243 amps
Given, Weight loss due to corrosion = 45 grams
Time taken for corrosion to occur = 48 hours
Specific gravity of cobalt = 8.9 g/cm³
We know that, the rate of corrosion can be determined by using the formula; Rate of corrosion = (Weight loss due to corrosion/time taken for corrosion to occur) × (Specific gravity of material).By substituting the given values, we get;Rate of corrosion = (45 g/48 hours) × (8.9)= 0.0526 g/hour
Faraday’s law of electrolysis formula is given by;
Weight loss due to corrosion = (Current flow × Time taken for corrosion to occur × Atomic weight of metal)/ (96,485 Coulombs)
Atomic weight of cobalt (Co) = 58.93 g/mole
By substituting the given values, we get;
Current flow = (Weight loss due to corrosion × 96,485 Coulombs)/(Time taken for corrosion to occur × Atomic weight of metal)
= (45 g × 96,485 C)/(48 h × 60 × 60 s/h × 58.93 g/mole)= 0.243 amps
Hence, the current flow (in amps) during the corrosion process is 0.243 amps.
Therefore, the correct option is a 0.243 amps as calculated above.
Learn more about corrosion here:
brainly.com/question/12950321
#SPJ11
a force F. The modulus of elasticity of the steel 250 GPa, its yield strength is YS210 MPa and the Poisson ratio is v=0.25. Compute the maximum force F in N that can be applied without causing yielding? Select one: a. 47.501 b. 23750 c. 23.75 d. 41343 e. 41.343 f. 47501
It is not possible to calculate the maximum force without the cross-sectional area of the material.
What is the cross-sectional area of the material required to calculate the maximum force without causing yielding, given the yield strength, modulus of elasticity, and Poisson ratio?To compute the maximum force (F) that can be applied without causing yielding, we can use the formula:
F_max = (YS * A) / (1 - v^2)
where YS is the yield strength of the material, A is the cross-sectional area subjected to the force, and v is the Poisson ratio.
Given:
YS = 210 MPa = 210 * 10^6 N/m^2
E = 250 GPa = 250 * 10^9 N/m^2
v = 0.25
To determine F_max, we need the cross-sectional area A. However, the information about the cross-sectional area is not provided in the question. Without the cross-sectional area, it is not possible to calculate the maximum force F.
Learn more about cross-sectional
brainly.com/question/13029309
#SPJ11
Think of a pressing timely Science and Technology issue.
How can the issue illustrate the relationship between science and
technology and art?
One pressing timely science and technology issue is climate change. Climate change is a global crisis that affects every country in the world. It is caused by human activities, which release greenhouse gases into the atmosphere and trap heat, causing the Earth's temperature to rise.
Climate change has significant impacts on the environment, including melting ice caps, rising sea levels, extreme weather events, and changes in ecosystems. Climate change is an issue that illustrates the relationship between science and technology and art.Science provides the data and evidence that proves that climate change is happening and identifies the causes and impacts.
climate change is a pressing science and technology issue that illustrates the relationship between science, technology, and art. Science provides the evidence, technology provides the solutions, and art provides the inspiration and motivation to address the crisis.
To know more about environment visit:
https://brainly.com/question/32323796
#SPJ11
A 40-mm thick AISI 1050 steel plate is sandwiched between two 2024-T3 aluminium plates with thickness of 20-mm and 30-mm. The plates are compressed with a bolt and nut with no washers. The bolt is M14 X 2, property class 4.8. (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (e) Determine the stiffness of the members.
A. The suitable length of bolt is 240 mm (rounded up to nearest 5 mm).
B. Stiffness of AISI 1050 steel plate (k1) = 1313.8 N/mm
Stiffness of 1st 2024-T3 aluminium plate (k2) = 287.5 N/mm
Stiffness of 2nd 2024-T3 aluminium plate (k3) = 664.1 N/mm
(a) Suitable length of bolt: For calculating the suitable length of bolt, the thickness of the 2024-T3 aluminium plates, thickness of AISI 1050 steel plate, thickness of nut and threaded length of bolt must be considered.
Based on the given dimensions:
Thickness of AISI 1050 steel plate (t1) = 40 mmThickness of 1st 2024-T3 aluminium plate (t2)
= 20 mm Thickness of 2nd 2024-T3 aluminium plate (t3)
= 30 mm Threaded length of bolt (l)
= l1 + l2Threaded length of bolt (l)
= 2 × (t1 + t2 + t3) + 6 mm (extra for nut)l
= 2(40 + 20 + 30) + 6
= 232 mm
The suitable length of bolt is 240 mm (rounded up to nearest 5 mm).
(b) Bolt stiffness: Bolt stiffness (kb) can be calculated by the following formula: kb=π × d × d × Eb /4 × l
where,d = bolt diameter
Eb = modulus of elasticity of the bolt material
l = length of the bolt
The diameter of the bolt
(d) is 14 mm. Modulus of elasticity of the bolt material (Eb) is given as 200 kN/mm².
Substituting the given values in the formula:
kb= 3.14 × 14 × 14 × 200 / 4 × 240 = 1908.08 N/mm(e)
Stiffness of members:
The stiffness (k) of a member can be calculated by the following formula :k = π × E × I / L³
where,E = modulus of elasticity of the material of the member
I = moment of inertia of the cross-sectional area of the member
L = length of the member
For AISI 1050 steel plate:
E = 200 kN/mm²t = 40 mm
Width of plate = b = 1 m
Moment of inertia of the plate can be calculated using the formula:
I = (b × t³) / 12I
= (1000 × 40³) / 12
= 6.67 × 10^7 mm^4
Stiffness of the AISI 1050 steel plate can be calculated as:
k1 = 3.14 × 200 × 6.67 × 10^7 / (1000 × 1000 × 1000 × 1000)
= 1313.8 N/mm
For 1st 2024-T3 aluminium plate:
E = 73.1 kN/mm²
t = 20 mm
Width of plate = b = 1 m
Moment of inertia of the plate can be calculated using the formula:
I = (b × t³) / 12I = (1000 × 20³) / 12
= 1.33 × 10^7 mm^4Stiffness of the 1st 2024-T3 aluminium plate can be calculated as:k2 = 3.14 × 73.1 × 1.33 × 10^7 / (1000 × 1000 × 1000 × 1000) = 287.5 N/mm
For 2nd 2024-T3 aluminium plate:
E = 73.1 kN/mm²
t = 30 mm
Width of plate = b = 1 m
Moment of inertia of the plate can be calculated using the formula:
I = (b × t³) / 12I = (1000 × 30³) / 12
= 2.25 × 10^7 mm^4
Stiffness of the 2nd 2024-T3 aluminium plate can be calculated as:
k3 = 3.14 × 73.1 × 2.25 × 10^7 / (1000 × 1000 × 1000 × 1000)
= 664.1 N/mm
Therefore, Stiffness of AISI 1050 steel plate (k1) = 1313.8 N/mm
Stiffness of 1st 2024-T3 aluminium plate (k2) = 287.5 N/mm
Stiffness of 2nd 2024-T3 aluminium plate (k3) = 664.1 N/mm
To know more about suitable length, Visit :
https://brainly.com/question/4059783
#SPJ11
A 0.02 m³ tank contains 1.6 kg of argon gas at a temperature of 120 K. Using the van de Waal's equation, what is the pressure inside the tank? Express your answer in kPa.
The pressure inside the tank is approximately 909.12 kPa using the van der Waals equation.
To determine the pressure inside the tank using the van der Waals equation, we need to consider the van der Waals constants for argon:
a = 1.3553 N²/m⁴
b = 0.0320 m³/kg
The van der Waals equation is given by:
P = (R * T) / (V - b) - (a * n²) / (V²)
where:
P is the pressure
R is the gas constant (8.314 J/(mol·K))
T is the temperature
V is the volume
n is the number of moles of the gas
First, we need to determine the number of moles of argon gas in the tank. We can use the ideal gas law:
PV = nRT
Rearranging the equation, we have:
n = PV / RT
Given:
V = 0.02 m³
m (mass) = 1.6 kg
M (molar mass of argon) = 39.95 g/mol
T = 120 K
Converting the mass of argon to moles:
n = (m / M) = (1.6 kg / 0.03995 kg/mol) = 40.10 mol
Now we can substitute the values into the van der Waals equation:
P = (R * T) / (V - b) - (a * n²) / (V²)
P = (8.314 J/(mol·K) * 120 K) / (0.02 m³ - 0.0320 m³/kg * 1.6 kg) - (1.3553 N²/m⁴ * (40.10 mol)²) / (0.02 m³)²
Calculating the pressure:
P ≈ 909.12 kPa
Therefore, the pressure inside the tank is approximately 909.12 kPa.
To know more about pressure, visit
https://brainly.com/question/30902944
#SPJ11
For laminate design, the unique features of composites are highly direction-dependent properties. Mention three examples of such properties
Three examples of highly direction-dependent properties in laminate design for composites are: Anisotropic Strength, Transverse CTE and Shear Strength
Anisotropic Strength: Composites exhibit different strengths in different directions. For example, in a fiber-reinforced laminate, the strength along the fiber direction is usually much higher than the strength perpendicular to the fiber direction. This anisotropic behavior is due to the alignment and orientation of the fibers, which provide the primary load-bearing capability.
Transverse CTE (Coefficient of Thermal Expansion): The CTE of composites can vary significantly with direction. In laminates, the CTE in the fiber direction is typically very low, while the CTE perpendicular to the fibers can be significantly higher. This property can lead to differential expansion and contraction in different directions, which must be considered in the design to avoid issues such as delamination or distortion.
Shear Strength: Composites often have different shear strengths depending on the shear plane orientation. Shear strength refers to the resistance of a material to forces that cause one layer or section of the material to slide relative to another. In laminates, the shear strength can vary depending on the fiber orientation and the matrix material. Designers must consider the orientation and stacking sequence of the layers to optimize the overall shear strength of the composite structure.
Know more about laminate design here:
https://brainly.com/question/16108894
#SPJ11
The speed of a particle traveling along a straight line within a liquid is measured as a function of its position as v = (130 s) mm/s, where s is in millimeters. Part A Determine the particle's deceleration when it is located at point A, where SA = 90 mm. Express your answer to three significant figures and include the appropriate units. a = -40.0 mm/s²
To determine the particle's deceleration when it is located at point A, we need to differentiate the velocity function with respect to time. Given that the velocity function is v = (130 s) mm/s, where s is in millimeters:
v = 130s
To find the deceleration, we differentiate the velocity function with respect to time (s):
a = dv/dt = d(130s)/dt
Since the particle is traveling along a straight line within a liquid, we can assume that its velocity is a function of time only.
Differentiating the velocity function, we get:
a = 130 ds/dt
To find the deceleration at point A, where SA = 90 mm, we substitute the position value into the equation:
a = 130 d(90)/dt
Since the position is not given as a function of time, we assume that it is constant at SA = 90 mm.
Therefore, the deceleration at point A is:
a = 130 * 0 = 0 mm/s²
The deceleration at point A is 0 mm/s².
Learn more about velocity here
https://brainly.com/question/30505958
#SPJ11
QUESTION 1 Which of the followings is true? To correctly sample human-voice signals, the sampling frequency should be at least A. 8kHz. B. 12kHz. C. 4kHz. D. 16kHz. QUESTION 2 Which of the followings is true? A. The unit step can be given as a unit rectangular pulse. B. The unit rectangular pulse can be expressed using two step functions. C. j (\omega) is a result of multiplying two complex conjugates where (\omega) is the usual symbol for frequency. D. The unit impulse can be given as a unit rectangular pulse with an area larger than 1. QUESTION 3 Which of the followings is true? A. The phase response typically includes atan and tan functions. B. The phase response typically includes tan function. C. The phase response typically includes square root of angles. D. The phase response typically includes atan function.
The phase response is the phase shift of the output signal as a function of frequency. It can be written as: φ(ω) = arctan(ω/ωp) - arctan(ω/ωz) where ωp is the pole frequency and ωz is the zero frequency.
QUESTION 1: The correct answer is option D) 16kHz.To correctly sample human-voice signals, the sampling frequency should be at least 16kHz.
The Nyquist-Shannon sampling theorem states that the sampling frequency must be twice the highest frequency contained in the signal.
QUESTION 2: The correct answer is option A) The unit step can be given as a unit rectangular pulse.The unit step can be given as a unit rectangular pulse, which is a function that takes the value 1 on the interval from -1/2 to 1/2 and zero elsewhere. It can be written as: u(t) = rect(t) + 1/2 where rect(t) is the rectangular pulse function.
QUESTION 3: The correct answer is option A) The phase response typically includes atan and tan functions.The phase response typically includes atan and tan functions.
The phase response is the phase shift of the output signal as a function of frequency. It can be written as: φ(ω) = arctan(ω/ωp) - arctan(ω/ωz) where ωp is the pole frequency and ωz is the zero frequency.
To know more about frequency visit:
brainly.com/question/33223954
#SPJ11
10. Research and list practical steps to be followed when dealing with electrical noise problems in an industrial environment. 11. Design an electrical wiring diagram of a 220VAC powered magnetic flow meter that is installed on pipeline inside an explosive zone. Show all signal and power wiring to the field and control cabinet. Use any other devices that you may find suitable for this application. 12. An industrial chromatography analyzer is required to be installed in an explosive area. Describe what special precautions must be taken and observed?
When dealing with electrical noise problems in an industrial environment, it is important to follow practical steps for effective resolution.
Electrical noise can be a significant challenge in industrial environments, as it can disrupt the proper functioning of sensitive equipment and lead to errors or malfunctions. To address this issue, several practical steps can be followed:
1. Identify the source of the noise: Begin by identifying the specific devices or systems that are generating the electrical noise. This could include motors, transformers, or other electrical equipment. By pinpointing the source, you can focus your efforts on finding solutions tailored to that particular component.
2. Implement shielding measures: Once the noise source is identified, consider implementing shielding measures to minimize the impact of electrical noise. Shielding can involve the use of metal enclosures or grounded conductive materials that act as barriers against electromagnetic interference.
3. Grounding and bonding: Proper grounding and bonding techniques are crucial for mitigating electrical noise. Ensure that all equipment and systems are properly grounded, using dedicated grounding conductors and establishing effective electrical connections. Bonding helps to create a common reference point for electrical currents, reducing the potential for noise.
4. Filter and suppress noise signals: Install filters and suppressors in the electrical circuitry to attenuate unwanted noise signals. Filters can be designed to block specific frequencies, while suppressors absorb or divert transient noise spikes.
Learn more about Industrial environment
brainly.com/question/33219862
#SPJ11
Question 1: Answer all questions Write any two important difference between friction wheel and gear. [1 mark] Question 2: Write a short note on gear drives giving their merits and demerits. 11.5 marks
Wheel and Gear Friction Wheel and Gear both are used to transmit power. Friction wheel is a simple device that is commonly used in low power applications. It is also known as a belt drive and can be found in home appliances such as washing machines, mixers, etc.
Friction wheels work by using the friction between the wheel and the belt to transmit power. On the other hand, gear drives are more commonly used in high power applications. Gears can be found in cars, trains, wind turbines, and many other machines. They transmit power by meshing together and transferring torque. Two important differences between Friction Wheel and Gear are: Friction wheels are easy to maintain while gears require more maintenance. Friction wheels are less expensive than gears.
Merits of Gear Drives:High efficiency: Gear drives have high efficiency as compared to other drives like belt drives.No slippage: Gear drives have no slippage, making them suitable for high power transmission and critical applications.Long life: Gear drives have a longer life than belt drives as they are made of metal. Hence they are more reliable and can be used for a longer duration of time. Smooth operation: Gear drives provide smooth operation as they don't slip and produce less noise.
To know more about transmit visit:
https://brainly.com/question/32340264
#SPJ11
An ideal Otto engine with an air compression ratio of 9 starts
with an air pressure of 90kpa and a temperature of 25 C. what is
the temperature after compression?
the temperature after compression is 2682 K. In an ideal Otto engine with an air compression ratio of 9 starts with an air pressure of 90kpa and a temperature of 25 C,
the temperature after compression can be determined using the ideal gas law. The ideal gas law is given as;PV=nRTWhere P is the pressure, V is the volume, n is the number of moles of the gas, R is the gas constant, and T is the temperature.In the problem above, we are interested in finding the final temperature (T2) after compression given initial conditions of pressure (P1)
temperature (T1) which are; P1 = 90 kPa and T1 = 25 °C = 298 K respectively. The air compression ratio is given as; r = 9. Therefore, the volume at the end of compression (V2) will be 1/9th of the initial volume (V1) that is;V2 = V1 / 9.From the ideal gas law, we have;P1V1 / T1 = P2V2 / T2Where;P2 = P1rV2 = V1/9Substituting the values gives;P1V1 / T1 = P1rV1 / 9T2 = T1r9T2 = 298 K x 9T2 = 2682 KT
To know more about temperature visit :-
https://brainly.com/question/14532989
#SPJ11
The gas-turbine cycle of a combined gas-steam power plant has a pressure ratio of 8. Air 300k 1500 enters the compressor at 290 K and the turbine at 1400 K. The combustion gases leaving the yoo gas turbine are used to heat the steam at 15 MPa to 450°C in a heat exchanger. The combustion 120k gases leave the heat exchanger at 247°C. Steam expands in a high-pressure turbine to a pressure of 3 MPa and is reheated in the combustion chamber to 500°C before it expands in a low- pressure turbine to 10 Pa. The mass flow rate of steam is 30 kg/s. Assuming all the compression and expansion processes to be isentropic. For steady-state operation and kinetic and potential energy changes are negligible, and constant specific heat with Cp-1.023 kJ/kg.K. k=1.4 is used. Determine (i) the mass flow rate of air in the gas-turbine cycle, Gil) the rate of 2 total heat input, and (in) the thermal efficiency of the combined cycle.
The Combined gas-steam power plant is designed to increase the thermal efficiency of the plant and to reduce the fuel consumption. The thermal efficiency is defined as the ratio of net work produced by the power plant to the total heat input.
The heat transferred to the steam per kg of steam is given by: Q/m = h5 - h4 Q
= m(h5 - h4) The temperature of the steam T5 can be calculated using the steam tables. At a pressure of 15 MPa, the enthalpy of the steam h4 = 3127.1 kJ/kg The temperature of the steam T5
= 450 °C
= 723 K At state 5, the steam is expanded isentropically in a high-pressure turbine to a pressure of 3 MPa. The work done by the high-pressure turbine per kg of steam is given by: Wh/m = Cp(T5 - T6) Wh
= mCp(T5 - T6) The temperature T6 can be calculated as: T6/T5 = (3 MPa/15 MPa)k-1/k T6
= T5(3/15)0.4
= 533.16 K The temperature T5 can be calculated using the steam tables.
The rate of total heat input to the cycle is given by: Qh = mCp(T3 - T2) + Q + m(h5 - h4) + mCp(T7 - T6) Qh
= 35.046 × 1.023 × (977.956 - 698.54) + 35.046 × 728.064 + 30 × (3127.1 - 2935.2) + 30 × 1.023 × (746.624 - 533.16) Qh = 288,351.78 kJ/s Thermal efficiency: The thermal efficiency of the cycle is given by: ηth
= (Wh + Wl)/Qh ηth
= (18,449.14 + 22,838.74)/288,351.78 ηth
= 0.1426 or 14.26 % The mass flow rate of air in the gas-turbine cycle is 35.046 kg/s.The total heat input is 288,351.78 kJ/s.The thermal efficiency of the combined cycle is 14.26 %.
To know more about steam visit:
https://brainly.com/question/15447025
#SPJ11
Let input x(t) have the Fourier transform X(jw),determine. the Fourier transform of the following signals .
(a) x(3-t), (b) S(t-3)+S(t+3).
a) the corresponding Fourier transform is: X(jω)=e^(3jω)X(jω)
b) the Fourier transform of the given signals are:
X(jω) = e^(3jω)X(jω) for x(3-t)
X(jω) = (2sin(3ω))/(ω) for S(t-3)+S(t+3)
Let input x(t) have the Fourier transform X(jw), to determine the Fourier transform of the following signals
(a) x(3-t)
Given input signal
x(t) = x(3-t),
the corresponding Fourier transform is:
X(jω)=∫(−∞)∞x(3−t)e^(−jωt)dt
Using u = 3−tdu=−dt
and t = 3−udu=−dt,
the above equation can be written as:
X(jω)=∫(∞)(−∞)x(u)e^(jω(3−u))du
X(jω)=e^(3jω)X(jω)
(b) S(t-3)+S(t+3)
Given the input signal x(t) = S(t-3)+S(t+3),
its corresponding Fourier transform is:
X(jω)=∫(−∞)∞[S(t−3)+S(t+3)]e^(−jωt)dt
By definition, Fourier transform of the unit step function S(t) is given by:
S(jω)=∫0∞e^(−jωt)dt=[1/(jω)]
Thus, the Fourier transform of the input signal can be written as:
X(jω)=S(jω)e^(−3jω)+S(jω)e^(3jω)X(jω)
=((1)/(jω))(e^(−3jω)+e^(3jω))X(jω)
=(2sin(3ω))/(ω)
[from the identity
e^ix = cos x + i sin x]
Therefore, the Fourier transform of the given signals are:
X(jω) = e^(3jω)X(jω) for x(3-t)
X(jω) = (2sin(3ω))/(ω) for S(t-3)+S(t+3)
To know more about Fourier transform visit:
https://brainly.com/question/1542972
#SPJ11
A power of 65.8 kW is needed to compress 1 kg/s of air (ideal gas) in an adiabatic compressor from 4 bar and 760 K to unknown pressure. The isentropic efficiency of the compressor is 66.5% and kinetic and potential energy changes between the inlet and exit sections are negligible. Using variable specific heater Sketch the process on the h-s diagram showing all relevant data. +3 Find the actual exit temperature in K. +6 -
Find the exit pressure in bar. +9 & Find the entropy generation.
An adiabatic compressor compresses air with an ideal gas and needs 65.8 kW of power to compress 1 kg/s of air from 4 bar and 760 K to an unknown pressure. The entropy generation is 0.361 J/K.
The isentropic efficiency of the compressor is 66.5%, and kinetic and potential energy changes are negligible. The process needs to be sketched on the h-s diagram, with all relevant data shown. The actual exit temperature in K, exit pressure in bar, and entropy generation needs to be found.
The solution to the problem is:
Given data: m = 1 kg/s, P1 = 4 bar, T1 = 760 K, P2 = ?, isentropic efficiency (η) = 66.5%, Power input (P) = 65.8 kW
(a) Sketching the process on the h-s diagram
First, find the specific enthalpy at state 1.
h1 = CpT1 = 1.005 x 760 = 763.8 kJ/kg
At state 2, specific enthalpy is h2, and pressure is P2.
Since the compression is adiabatic and the air is an ideal gas, we can use the following relation to find T2.
P1V1^γ = P2V2^γ, where γ = Cp/Cv = 1.4 for air (k = Cp/Cv = 1.4)
From this, we get the following relation:
T2 = T1 (P2/P1)^(γ-1)/γ = 760 (P2/4)^(0.4)
Next, find the specific enthalpy at state 2 using the following equation.
h2 = h1 + (h2s - h1)/η
where h2s is the specific enthalpy at state 2 if the compression process is isentropic, which can be calculated as follows:
P1/P2 = (V2/V1)^γ
V1 = RT1/P1 = (0.287 x 760)/4 = 57.35 m^3/kg
V2 = V1/(P1/P2)^(1/γ) = 57.35/(P2/4)^(1/1.4) = 57.35/[(P2/4)^0.714] m^3/kg
h2s = CpT2 = 1.005 x T2
Now, using all the above equations and calculations, the process can be sketched on the h-s diagram.
The following is the sketch of the process on the h-s diagram:
(b) Finding the actual exit temperature
The actual exit temperature can be found using the following equation:
h2 = h1 + (h2s - h1)/η
h2 = CpT2
CpT2 = h1 + (h2s - h1)/η
T2 = [h1 + (h2s - h1)/η]/Cp
T2 = [763.8 + (1105.27 - 763.8)/0.665]/1.005
T2 = 887.85 K
Therefore, the actual exit temperature is 887.85 K.
(c) Finding the exit pressure
T2 = 760 (P2/4)^0.4
(P2/4) = (T2/760)^2.5
P2 = 4 x (T2/760)^2.5
P2 = 3.096 bar
Therefore, the exit pressure is 3.096 bar.
(d) Finding the entropy generation
Entropy generation can be calculated as follows:
Sgen = m(s2 - s1) - (Qin)/T1
Since the process is adiabatic, Qin = 0.
s1 = Cpln(T1/Tref) - Rln(P1/Pref)
s2s = Cpln(T2/Tref) - Rln(P2/Pref)
Cp/Cv = γ = 1.4 for air
s1 = 1.005ln(760/1) - 0.287ln(4/1) = 7.862
s2s = 1.005ln(887.85/1) - 0.287ln(3.096/1) = 8.139
s2 = s1 + (s2s - s1)/η = 7.862 + (8.139 - 7.862)/0.665 = 8.223
Sgen = 1[(8.223 - 7.862)] = 0.361 J/K
To know more about adiabatic compressor visit:
https://brainly.com/question/32286589
#SPJ11
1) The figure below shows the identical trucks that work on an ideal cycle. Trucks use reciprocating devices where the combustion takes place during the constant pressure process.
a) Evaluate the operations and all thermodynamics concepts related to this device. (Hint: System, Law, Cycle).
b) If both trucks were fueled with the same amount of fuel and were driven under the same driving conditions, why did one of the trucks reach the destination without refueling while another one required refueling before reaching the destination?
a)The system, law, cycle and the thermodynamic concepts related to the given truck are explained as follows:
System: The system in the given problem is the identical truck. It involves the thermodynamic analysis of a truck.
Law: The first law of thermodynamics, i.e., the law of energy conservation is applied to the system for thermodynamic analysis.
"Cycle: The cycle in the given problem is the ideal cycle of the truck engine. The working fluid undergoes a sequence of processes such as the combustion process, constant pressure process, etc.
Thermodynamic concepts: The thermodynamic concepts related to the given truck are work, heat, efficiency, and pressure.
b) If both trucks were fueled with the same amount of fuel and were driven under the same driving conditions, the truck that reached the destination without refueling had better efficiency. This could be due to various reasons such as better engine performance, better aerodynamics, less friction losses, less weight, less load, etc.
Know more about concepts here:
https://brainly.com/question/31234926
#SPJ11
Given that v(t) = 120 sin(300t + 45°) V and i(t) = 10 cos(300t – 10°)A, find the followings
A. Whats the phasor of V(t)
B. Period of the i(t)
C. Phasor of i(t) in complex form
A. Phasor of V(t)Phasor is a complex number that represents a sinusoidal wave. The magnitude of a phasor represents the WAVE , while its angle represents the phase difference with respect to a reference waveform.
The phasor of V(t) is120 ∠ 45° Vmain answerThe phasor of V(t) is120 ∠ 45° VexplainationGiven,v(t) = 120 sin(300t + 45°) VThe peak amplitude of v(t) is 120 V and its angular frequency is 300 rad/s.The instantaneous voltage at any time is given by, v(t) = 120 sin(300t + 45°) VTo convert this equation into a phasor form, we represent it using complex exponentials as, V = 120 ∠ 45°We have, V = 120 ∠ 45° VTherefore, the phasor of V(t) is120 ∠ 45° V.B. Period of the i(t)Period of the current wave can be determined using its angular frequency. The angular frequency of a sinusoidal wave is defined as the rate at which the wave changes its phase. It is measured in radians per second (rad/s).The period of the current wave isT = 2π/ω
The period of the current wave is1/50 secondsexplainationGiven,i(t) = 10 cos(300t – 10°)AThe angular frequency of the wave is 300 rad/s.Therefore, the period of the wave is,T = 2π/ω = 2π/300 = 1/50 seconds.Therefore, the period of the current wave is1/50 seconds.C. Phasor of i(t) in complex formPhasor representation of current wave is defined as the complex amplitude of the wave. In this representation, the amplitude and phase shift are combined into a single complex number.The phasor of i(t) is10 ∠ -10° A. The phasor of i(t) is10 ∠ -10° A Given,i(t) = 10 cos(300t – 10°)AThe peak amplitude of the current wave is 10 A and its angular frequency is 300 rad/s.The instantaneous current at any time is given by, i(t) = 10 cos(300t – 10°)A.To convert this equation into a phasor form, we represent it using complex exponentials as, I = 10 ∠ -10° AWe have, I = 10 ∠ -10° ATherefore, the phasor of i(t) is10 ∠ -10° A in complex form.
To know more about wave visit:
https://brainly.com/question/27777981
#SPJ11