Q5 Ethylene glycol, a common antifreeze, is made from the reaction of ethylene chlorohydrin and sodium bicarbonate as shown below: CH2OH-CH2Cl + NaHCO3 CH2OH-CH2OH + NaCl + CO2 The reaction is essentially irreversible and is first-order in each reactant, and the reaction rate constant at 82°C is 5 L/gmol.hr. A reaction mixture at 82°C with a volume of 20 liters contains ethylene chlorohydrin and sodium bicarbonate, both at concentrations of 0.6 M. What is the reaction rate of ethylene chlorohydrin (in gmol/L.hr)? (Equations 10 points, solution 10 points, answer 10 points)

The amount of methane produced in m³/day is 12,705 m³/day.

To calculate the amount of methane produced, we need to determine the total amount of COD utilized and then convert it into cell tissue. Given that 90% of the bsCOD is removed, we can calculate the COD utilized as follows:

COD utilized = 0.9 × bsCOD concentration

= 0.9 × 7,000 g/m³

= 6,300 g/m³

Next, we need to convert the COD utilized into cell tissue using the net biomass synthesis yield (Yn) of 0.04 gVSS/gCOD:

CODsyn = 1.42 × Yn × COD utilized

= 1.42 × 0.04 × 6,300 g/m³

= 356.4 gVSS/m³

Now, to determine the amount of methane produced, we need to convert the VSS (volatile suspended solids) into methane using stoichiometric conversion factors. The stoichiometric ratio for methane production from VSS is approximately 0.35 m³CH₄/kgVSS.

Methane produced = VSS × stoichiometric ratio

= 356.4 g/m³ × (1 kg/1,000 g) × (0.35 m³CH₄/kgVSS)

= 0.12474 m³CH₄/m³

Finally, we can calculate the amount of methane produced in m³/day by multiplying it by the flow rate of the wastewater:

Methane produced (m³/day) = 0.12474 m³CH₄/m³ × 1,500 m³/day

= 187.11 m³/day

Therefore, the amount of methane produced in m³/day is approximately 187.11 m³/day.

Learn more about: Amount of COD

brainly.com/question/5993118

#SPJ11

a) The work done during the reversible isothermal compression is -2012.2 J.

b) The work is done on the gas by the surroundings.

c) The work done during the reversible adiabatic compression is -1594.7 J.

a) In the given scenario, the work done during the reversible isothermal compression is determined to be -2012.2 J. This value is obtained by using the formula for work done in an isothermal process, which is given by

[tex]W = -nRT ln(V_f/V_i)[/tex]

Where n is the number of moles of the gas, R is the ideal gas constant, T is the temperature in Kelvin, Vi is the initial volume, and Vf is the final volume. By substituting the given values into the formula, we can calculate the work done.

b) In the process of reversible isothermal compression, the work is done on the gas by the surroundings. This means that external forces are acting on the gas, causing it to decrease in volume. As a result, the gas is compressed, and work is done on it. The negative sign in the work value indicates that work is being done on the system.

c) In the case of reversible adiabatic compression under the given conditions, the work done is found to be -1594.7 J. This is calculated using the formula for work done in an adiabatic process, which is given by

W = (PfVf - PiVi) / (γ - 1)

Where Pf and Pi are the final and initial pressures respectively, Vf and Vi are the final and initial volumes, and γ is the adiabatic coefficient. By substituting the given values into the formula, we can determine the work done.

Learn more about reversible adiabatic

brainly.com/question/30886775

#SPJ11

a) There is an azeotrope in this binary system. For azeotrope, the activity coefficient of both A and B should be equal at the same mole fraction. Here, lnγA=0.5xB2 and lnγB=0.5xA2

Given, Temperature (T) = 80°C = (80 + 273.15) K = 353.15 K The vapor pressures of A and B at 80°C are PAsatv=900 mm Hg and PBsat = 600 mm Hg.

Let, the mole fraction of A in the azeotrope be x* and mole fraction of B be (1 - x*). Now, from Raoult's law for A, PA = x* PAsatv for B, PB = (1 - x*) PBsat For azeotrope,PA = x* PAsatv = P* (where P* is the pressure of the azeotrope)PB = (1 - x*) PBsat = P*

From the above two equations,x* = P*/PAsatv = (600/900) = 0.67(1 - x*) = P*/PBsat = (600/900) = 0.67

Therefore, the azeotropic pressure at 80°C in the binary system A-B is P* = 0.67 × PAsatv = 0.67 × 900 = 603 mm HgThe mole fractions of A and B in the azeotrope are x* = 0.67 and (1 - x*) = 0.33, respectively.

b) To calculate the pressure above a liquid with a mole fraction of A of 0.2 and composition of the vapor in equilibrium with it, we will use Raoult's law.PA = 0.2 × PAsatv = 0.2 × 900 = 180 mm HgPB = 0.8 × PBsat = 0.8 × 600 = 480 mm Hg

The total vapor pressure, P = PA + PB = 180 + 480 = 660 mm Hg

Mole fraction of A in vapor, YA = PA / P = 180 / 660 = 0.27Mole fraction of B in vapor, YB = PB / P = 480 / 660 = 0.73

Therefore, the pressure above a liquid with a mole fraction of A of 0.2 would be 660 mm Hg and the composition of the vapor in equilibrium with it would be 0.27 and 0.73 for A and B, respectively.

More on azeotropic pressure: https://brainly.com/question/32388536

#SPJ11

he surface coverage 6 is given as a function of [A2] as: K1/2[AZ]1/2 O = 1+ K1/2[42]1/2

Adsorption is the physical or chemical bonding of molecules, atoms, or ions from a gas, liquid, or dissolved solid to a surface. Adsorption with dissociation is the dissociation of adsorbed molecules into ions on the surface. The rate of the adsorption and desorption processes are equal at the equilibrium state.

The surface coverage, θ, is the number of adsorbed molecules on a unit area of the surface. When considering adsorption with dissociation, the adsorption and dissociation reaction can be represented as Az +S+S → A-S+A-S.At the equilibrium state, the rate of adsorption, Rads = Rdesθ, where Rads is the rate of adsorption, Rdes is the rate of desorption, and θ is the surface coverage. Also, the number of adsorption sites is equal to the number of adsorbed molecules, hence θ = N/M, where N is the number of adsorbed molecules and M is the number of adsorption sites.Substituting the above expressions in the rate equation, Rads = Rdesθ gives Kads[Az] = Kdes[A-S][A-S], where Kads and Kdes are the equilibrium constants for adsorption and desorption respectively.Rearranging the above expression, [Az]/[A-S][A-S] = Kdes/KadsWhen the adsorption is at equilibrium, the total concentration of the adsorbed species is equal to the concentration of the free species in the solution.

Thus, [Az] = [A2] - [A-S] and [A-S] = θM. Substituting the above equations, K1/2[A2]1/2 = 1 + K1/2[θM]1/2 O, where O is the coverage parameter and K is the adsorption equilibrium constant. This equation shows the dependence of the surface coverage on the concentration of the adsorbate and the coverage parameter. This formula is useful in evaluating the adsorption isotherm of the system.

Learn more about molecules:

https://brainly.com/question/32298217

#SPJ11

Due to the combined effect of the forces acting on solid particles in liquids, solid particles in a liquid exhibit a continuous and random motion known as Brownian motion.

When solid particles are suspended in a liquid, they can exhibit various types of movement due to the forces acting upon them.

The movement of solid particles in a liquid is known as Brownian motion. This motion is caused by the random collision of liquid molecules with solid particles.

The forces operating in the movement of solid particles in a liquid include:

Learn more about Brownian motion at: https://brainly.com/question/2604539

#SPJ4

The movement of solid particles in a liquid can be explained by diffusion and sedimentation.

In addition, Brownian motion, a random motion of particles suspended in a liquid, also plays a role. The particles' motion is influenced by gravitational, viscous, and interparticle forces. The solid particles in a liquid have a random motion that causes them to collide with one another. The rate of collision is influenced by factors such as particle concentration, viscosity, and temperature. The movement of solid particles in a liquid is governed by the following principles:

Diffusion is the process by which particles spread out in a fluid. The rate of diffusion is influenced by temperature, particle size, and the concentration gradient. A concentration gradient exists when there is a difference in concentration across a distance. In other words, the rate of diffusion is proportional to the concentration gradient. Diffusion is essential in biological processes such as respiration and excretion.Sedimentation is the process by which heavier particles settle to the bottom of a container under the influence of gravity. The rate of sedimentation is influenced by the size and shape of the particle, the viscosity of the liquid, and the strength of the gravitational field. Sedimentation is important in the separation of liquids and solids.

Brownian motion is the random motion of particles suspended in a fluid due to the impact of individual fluid molecules. The rate of Brownian motion is influenced by the size of the particles, the temperature, and the viscosity of the fluid. Brownian motion is important in the movement of particles in biological systems.  The forces operating on solid particles in a liquid are gravitational force, viscous force and interparticle force. The gravitational force pulls particles down towards the bottom of the liquid container, while the viscous force acts to slow down the movement of particles. The interparticle force is the force that particles exert on each other, causing them to either attract or repel. These forces play a crucial role in determining the motion of particles in a liquid.

Learn more about diffusion:

https://brainly.com/question/14852229

#SPJ11

Glycogen metabolism is regulated by two hormones, insulin, and glucagon. When the glucose level in the body is high, insulin is secreted from the pancreas, and when the glucose level is low, glucagon is secreted.

Let us describe the coordinated regulation of glycogen metabolism in response to the hormone glucagon. This regulation leads to the breakdown of glycogen in the liver and the release of glucose into the bloodstream. The breakdown of glycogen is carried out by the following enzymes, regulated by the hormone glucagon:

Phosphorylase kinase: The activity of this enzyme is increased by glucagon. The increased activity leads to the activation of the phosphorylase enzyme, which is responsible for the cleavage of glucose molecules from the glycogen chain. The cleaved glucose molecules then get converted into glucose-1-phosphate.

Glycogen phosphorylase: This enzyme is responsible for the cleavage of glucose molecules from the glycogen chain. Glucagon increases the activity of phosphorylase kinase, which in turn increases the activity of glycogen phosphorylase.

Enzyme debranching: Glucagon also activates the debranching enzyme, which removes the branches of the glycogen chain. The removed branches are then converted into glucose molecules that are released into the bloodstream.

Learn more about Glycogen metabolism:

https://brainly.com/question/31477221

#SPJ11

2. The interaction involved in the B⁺-decay is known as beta decay.

3.  The conserved quantities in the reaction are:

The quark flavor is not a conserved quantity in the given reaction of B⁺-decay.

The B⁺-decay is a type of beta decay, specifically beta plus decay. In beta plus decay, a proton (p) decays into a neutron (n), emitting a positron (e+) and an electron neutrino (νe):

p → n + e⁺ + νe

2. The interaction involved in the B⁺-decay is the weak nuclear force. The weak force is responsible for processes involving the transformation of particles, such as the conversion of a proton into a neutron in this case.

The interaction involved in the B⁺-decay is known as beta decay. Specifically, the B⁺-decay refers to the decay of a positively charged (B⁺) meson, which is a type of subatomic particle.

3. The conserved quantities in the reaction are:

Conservation of electric charge: The total charge on both sides of the reaction is conserved. The proton (p) has a charge of +1, while the neutron (n) has no charge. The positron (e⁺) has a charge of +1, which balances out the charge.

Conservation of lepton number: The total lepton number is conserved in the reaction. The lepton number of the proton and neutron is 0, while the lepton number of the positron and electron neutrino is also 0. Hence, the lepton number is conserved.

Conservation of baryon number: The baryon number is conserved in the reaction. The baryon number of the proton is 1, and the baryon number of the neutron is also 1. Therefore, the total baryon number is conserved.

Regarding quark flavor, it is not conserved in the B⁺-decay. The decay process involves the transformation of a up-type quark (u) in the proton to a down-type quark (d) in the neutron. This change in quark flavor is allowed by the weak force.

Learn more about Weak Nuclear Force at

brainly.com/question/31753095

#SPJ4

The heat demand of the reactor is:Q = 112.79 kJ + 206.0 kJQ = 318.79 kJ or 319 kJ (rounded off to the nearest integer).Therefore, the heat demand of the reactor is 319 kJ.

Synthesis gas is formed from the catalytic reforming of methane gas with steam at high temperatures and atmospheric pressure. The reaction produces a mixture of CO and H2, as follows: CH4(g) + H2O(g) → CO(g) + 3H2(g)Additionally, the water-gas shift reaction is the only other reaction considered in this process. The reaction proceeds as follows: CO(g) + H2O(g) → CO2(g) + H2(g). The reactants are supplied in the ratio of 2 mol of steam to 1 mol of CH4. Heat is added to the reactor to raise the temperature of the products to 1300 K, with the CH4 being entirely converted. The product stream contains 17.4 mol-% CO. Calculate the heat demand of the reactor, assuming that the reactants are preheated to 600 K.Methane (CH4) reacts with steam (H2O) to form carbon monoxide (CO) and hydrogen (H2).

According to the balanced equation, one mole of CH4 reacts with two moles of H2O to produce one mole of CO and three moles of H2.To calculate the heat demand of the reactor, the reaction enthalpy must first be calculated. The enthalpy of reaction for CH4(g) + 2H2O(g) → CO(g) + 3H2(g) is ΔHrxn = 206.0 kJ/mol. The reaction enthalpy can be expressed in terms of ΔH°f as follows:ΔHrxn = ∑ΔH°f(products) - ∑ΔH°f(reactants)Reactants are preheated to 600 K.

The heat requirement for preheating the reactants must be calculated first. Q = mcΔT is the formula for heat transfer, where Q is the heat transferred, m is the mass of the substance, c is the specific heat of the substance, and ΔT is the temperature difference. The heat required to preheat the reactants can be calculated as follows:Q = (1 mol CH4 × 16.04 g/mol × 600 K + 2 mol H2O × 18.02 g/mol × 600 K) × 4.18 J/(g·K)Q = 112792.8 J or 112.79 kJThe reaction produces 1 mole of CO and 3 moles of H2.

Thus, the mol fraction of CO in the product stream is (1 mol)/(1 mol + 3 mol) = 0.25. But, according to the problem, the product stream contains 17.4 mol-% CO. This implies that the total number of moles in the product stream is 100/17.4 ≈ 5.75 moles. Thus, the mole fraction of CO in the product stream is (0.174 × 5.75) / 1 = 1.00 mol of CO. Thus, the amount of CO produced is 1 mol.According to the enthalpy calculation given above, the enthalpy of reaction is 206.0 kJ/mol. Thus, the heat produced in the reaction is 206.0 kJ/mol of CH4. But, only 1 mol of CH4 is consumed. Thus, the amount of heat produced in the reaction is 206.0 kJ/mol of CH4.The heat demand of the reactor is equal to the heat required to preheat the reactants plus the heat produced in the reaction.

Therefore, the heat demand of the reactor is:Q = 112.79 kJ + 206.0 kJQ = 318.79 kJ or 319 kJ (rounded off to the nearest integer).Therefore, the heat demand of the reactor is 319 kJ.

Learn more about reactor

https://brainly.com/question/29123819

#SPJ11

Therefore, the pH of a 0.369 M solution of carbonic acid is approximately 5.91.

To calculate the pH of a solution of carbonic acid (H2CO3), we need to consider the dissociation of carbonic acid and the equilibrium expression for its ionization.

The dissociation of carbonic acid can be represented as follows:

H2CO3 ⇌ H+ + HCO3-

The equilibrium expression for this dissociation is:

Ka1 = [H+][HCO3-]/[H2CO3]

Given that the Ka1 value for carbonic acid is 4.50 x 10^-7, we can set up an ICE (Initial, Change, Equilibrium) table to determine the concentration of H+ in the solution.

Let's assume x mol/L is the concentration of H+.

H2CO3 ⇌ H+ + HCO3-

Initial: 0 0 0.369 M

Change: -x +x +x

Equilibrium: 0 x 0.369 + x

Using the equilibrium expression, we can write:

4.50 x 10^-7 = (x)(0.369 + x)

Since the value of x is much smaller compared to 0.369, we can assume that x is negligible in comparison and simplify the equation:

4.50 x 10^-7 ≈ (x)(0.369)

Solving this equation for x gives:

x ≈ 4.50 x 10^-7 / 0.369

x ≈ 1.22 x 10^-6

The concentration of H+ in the solution is approximately 1.22 x 10^-6 M.

To calculate the pH of the solution, we use the equation:

pH = -log[H+]

pH = -log(1.22 x 10^-6)

pH ≈ 5.91

Therefore, the pH of a 0.369 M solution of carbonic acid is approximately 5.91.

Learn more about carbonic acid here

https://brainly.com/question/31314818

#SPJ11

The time it takes for the ejected electrons to travel 2.75 cm to the detection device is approximately 2.165 ns.

To determine the time it takes for the ejected electrons to travel a distance of 2.75 cm to the detection device, we need to calculate their speed first. We can use the energy of the incident photons and the work function of the material to find the kinetic energy of the ejected electrons, and then apply the classical kinetic energy equation. Assuming the electrons have negligible initial velocity:

1. Calculate the energy of the incident photons:

Energy = hc / λ

where:

h is Planck's constant (6.626 x 10⁻³⁴ J·s),

c is the speed of light (3 x 10⁸ m/s),

λ is the wavelength of the photons (487 nm).

Converting wavelength to meters:

λ = 487 nm = 487 x 10⁻⁹ m

Substituting the values into the equation and converting to electron volts (eV):

Energy = (6.626 x 10⁻³⁴ J·s × 3 x 10⁸ m/s) / (487 x 10⁻⁹  m) = 4.065 eV

2. Calculate the kinetic energy of the ejected electrons:

Kinetic Energy = Energy - Work Function

where the work function is given as 2.43 eV.

Kinetic Energy = 4.065 eV - 2.43 eV = 1.635 eV

3. Convert the kinetic energy to joules:

1 eV = 1.6 x 10⁻¹⁹  J

Kinetic Energy = 1.635 eV × (1.6 x 10⁻¹⁹ J/eV) = 2.616 x 10⁻¹⁹ J

4. Apply the classical kinetic energy equation:

Kinetic Energy = (1/2) × m × v²

where m is the mass of the electron and v is its velocity.

Rearranging the equation to solve for velocity:

v = √(2 × Kinetic Energy / m)

The mass of an electron, m = 9.11 x 10⁻³¹ kg.

Substituting the values and calculating the velocity:

v = √(2 × 2.616 x 10⁻¹⁹ J / 9.11 x 10⁻³¹ kg) ≈ 1.268 x 10⁷ m/s

5. Calculate the time to travel 2.75 cm:

Distance = 2.75 cm = 2.75 x 10⁻² m

Time = Distance / Velocity = (2.75 x 10⁻² m) / (1.268 x 10⁷ m/s) ≈ 2.165 x 10⁻⁹ seconds

Converting to nanoseconds:

Time ≈ 2.165 ns

Therefore, it will take approximately 2.165 nanoseconds for the ejected electrons to travel 2.75 cm to the detection device.

Read more about Kinetic Energy here: https://brainly.com/question/8101588

#SPJ11

(a) The value of the energy gap in the GaN semiconductor used in the blue-violet LED is approximately 2.88 eV.

(b) The potential drop across this LED when it's operating is approximately 2.88 V.

(a) The energy gap, also known as the bandgap, is the energy difference between the valence band and the conduction band in a semiconductor material. It determines the energy required for an electron to transition from the valence band to the conduction band.

For a blue-violet LED made with GaN (Gallium Nitride) semiconductor that emits light at 430 nm, we can use the relationship between energy and wavelength to determine the energy gap. The energy of a photon is given by the equation E = hc/λ, where h is Planck's constant (6.626 x 10⁻³⁴ J·s), c is the speed of light (3 x 10⁸ m/s), and λ is the wavelength.

Converting the wavelength to meters:

430 nm = 430 x 10⁻⁹ m

Using the equation E = hc/λ, we can calculate the energy of the blue-violet light:

E = (6.626 x 10⁻³⁴ J·s) * (3 x 10⁸ m/s) / (430 x 10⁻⁹ m) ≈ 4.61 x 10⁻¹⁹ J

Converting the energy from joules to electron volts (eV):

1 eV = 1.602 x 10⁻¹⁹ J

Dividing the energy by the conversion factor:

Energy in eV = (4.61 x 10⁻¹⁹ J) / (1.602 x 10⁻¹⁹ J/eV) ≈ 2.88 eV

Therefore, the value of the energy gap in the GaN semiconductor used in the blue-violet LED is approximately 2.88 eV.

(b) The potential drop across an LED when it's operating is typically equal to the energy gap of the semiconductor material. In this case, since the energy gap of the GaN semiconductor is approximately 2.88 eV, the potential drop across the LED when it's operating is approximately 2.88 V.

The potential drop is a result of the energy difference between the electron in the conduction band and the hole in the valence band. This potential drop allows the LED to emit light when electrons recombine with holes, releasing energy in the form of photons.

Potential drop (V) = Energy gap (eV) / electron charge (e)

The energy gap in the GaN semiconductor is approximately 2.88 eV. The electron charge is approximately 1.602 x 10⁻¹⁹ coulombs (C).

Substituting these values into the equation, we can calculate the potential drop:

Potential drop = 2.88 V x 1.602 x 10⁻¹⁹ C / (1.602 x 10⁻¹⁹  C)

≈ 2.88 V

LEDs (Light Emitting Diodes) are widely used in various electronic devices and lighting applications. Understanding the energy gaps of semiconductor materials is crucial in designing LEDs that emit light of different colors. Different semiconductor materials have varying energy gaps, which determine the wavelength and energy of the emitted light. GaN is a commonly used material for blue-violet LEDs due to its suitable energy gap for emitting this specific color of light.

Learn more about energy gap

brainly.com/question/32782187

#SPJ11

The power output of the expander is 52.87 kW for the first set of operating conditions and 41.55 kW for the second set of operating conditions. The temperature of the exhaust stream is 123.7 K for the first set of operating conditions and 104.7 K for the second set of operating conditions.

In the given problem, a nitrogen expander is adiabatically operating with the following parameters: Inlet temperature T1Inlet pressure P1Molar flow rate n Exhaust pressure P2Expander efficiency ηThe task is to calculate the power output of the expander and the temperature of the exhaust stream. Let's calculate the power output of the expander using the following equation: Power = nRT1 η{1 - [(P2/P1) ^ ((k - 1) / k)]}where k is the ratio of specific heats. Rearranging the equation, we get: Power = nRT1 η [1 - exp (((k - 1) / k) ln (P2/P1))]Put the values in the above equation and solve it for both the cases.

(a) T1 = 480°C, P1 = 6 bar, n = 200 mol-s-1, P2 = 1 bar, η = 0.80k = 1.4 for nitrogen gas.R = 8.314 kJ/mol KPower = 200 * 8.314 * (480 + 273) * 0.80 / (1.4 - 1) * [1 - exp (((1.4 - 1) / 1.4) * ln (1/6))]Power = 52.87 kW

(b) T1 = 400°C, P1 = 5 bar, n = 150 mol-s-1, P2 = 1 bar, η = 0.75R = 8.314 kJ/mol KPower = 150 * 8.314 * (400 + 273) * 0.75 / (1.4 - 1) * [1 - exp (((1.4 - 1) / 1.4) * ln (1/5))]Power = 41.55 kW

The next step is to calculate the temperature of the exhaust stream. We can use the following equation to calculate the temperature:T2 = T1 (P2/P1)^((k-1)/k)Put the values in the above equation and solve it for both the cases.

(a) T2 = 480 * (1/6) ^ ((1.4-1)/1.4)T2 = 123.7 K

(b) T2 = 400 * (1/5) ^ ((1.4-1)/1.4)T2 = 104.7 K

Learn more about expander:

https://brainly.com/question/29888686

#SPJ11

The molar solubility of the salt that produces  [X²⁺](aq) and [Y³⁻] (aq) ions is 7.39 x 10⁻⁹ M.

To calculate the molar solubility of the salt, we must find the volume of the solution first.

Volume of solution, V = 100mL (or) 100cm³

We know that for the sparingly soluble salt, X3Y2, the equilibrium is given by the following equation:

⟶ X3Y2(s) ⇋ 3X²⁺(aq) + 2Y³⁻(aq)

At equilibrium, Let the solubility of X3Y2 be ‘S’ moles per liter. Then, The equilibrium concentration of X²⁺ is 3S moles per liter.

The equilibrium concentration of Y³⁻ is 2S moles per liter. The solubility product constant (Ksp) of X3Y2 is given by:

Ksp = [X²⁺]³ [Y³⁻]²

But we know that [X²⁺] = 3S and [Y³⁻] = 2S

Thus, Ksp = (3S)³(2S)²

Ksp = 54S⁵or

S = (Ksp/54)⁰⁽.⁵⁾

S = (1.50 x 10⁻²¹/54)⁰⁽.⁵⁾

= 7.39 x 10⁻⁹ mol/L (or) 7.39 x 10⁻⁶ g/L

Therefore, the molar solubility of the given salt is 7.39 x 10⁻⁹ M.

Learn more about molar solubility: https://brainly.com/question/31493083

#SPJ11

The hybridization of each atom is given below: C₁: sp³ C₂: sp³ N: sp³

a. N₂ H

The Lewis structure of N₂H is given below:

Bond analysis:

Total no of valence electrons in N2H = 1(2) + 2(5) + 1 = 12

Valence electrons in N₂H2 will be = 12/2 = 6

No of sigma bonds in N2H = 2

No of lone pairs on nitrogen = 1

Valence shell energy level orbitals diagram for N2H is given below:

Promotion is not required since N has no lone pair. Hybridization step of N2H is given below:

Thus, the hybridization of N2H is sp³.

Diagram of overlapping orbitals with label of types of bonds formed is given below:

b. CH₃-NH₂

The Lewis structure of CH₃-NH₂ is given below:

Bond analysis:

Total no of valence electrons in CH₃NH₂ = 1(4) + 3(1) + 1(5) + 2(1) = 14

Valence electrons in CH₃NH₂ will be = 14/2 = 7

No of sigma bonds in CH₃NH₂ = 4

No of lone pairs on nitrogen = 1

Valence shell energy level orbitals diagram for CH₃NH₂ is given below:

The hybridization of each atom is given below: C₁: sp³ C₂: sp³ N: sp³

Promotion, hybridization step and hybrid outcome are shown clearly, if applicable. Overlapping orbitals with label of types of bonds (σ or π) formed.

Learn more about hybridization

https://brainly.com/question/29020053

#SPJ11

Approximately 27.44 grams of nitrogen (N₂) would be required to fill the balloon to the same pressure, volume, and temperature as the given 0.14 g of helium (He).

To determine the mass of nitrogen (N₂) required to fill the balloon to the same pressure, volume, and temperature as the given 0.14 g of helium (He), we need to use the ideal gas law equation:

PV = nRT

where P is the pressure, V is the volume, n is the number of moles of gas, R is the ideal gas constant, and T is the temperature.

Since the pressure, volume, and temperature are the same for both gases, we can compare the number of moles of helium (He) and nitrogen (N₂) using their molar masses.

The molar mass of helium (He) is approximately 4 g/mol, and the molar mass of nitrogen (N₂) is approximately 28 g/mol.

Using the equation: n = mass / molar mass

For helium (He): n(He) = 0.14 g / 4 g/mol
For nitrogen (N₂): n(N₂) = (0.14 g / 4 g/mol) * (28 g/mol / 1)

Simplifying: n(N₂) = 0.14 g * (28 g/mol) / (4 g/mol)

Calculating: n(N₂) = 0.14 g * 7

The number of moles of nitrogen (N₂) required to fill the balloon to the same pressure, volume, and temperature is 0.98 moles.

To find the mass of nitrogen (N₂) required, we can use the equation: mass = n * molar mass

mass(N₂) = 0.98 moles * 28 g/mol

Calculating: mass(N₂) = 27.44 g

Therefore, approximately 27.44 grams of nitrogen (N₂) would be required to fill the balloon to the same pressure, volume, and temperature as the given 0.14 g of helium (He).

To know more about nitrogen, refer

https://brainly.com/question/15842685

#SPJ11

novative materials refer to materials that have been recently developed to produce new applications or enhance the performance of existing products. One of the most innovative materials is graphene, which is a single-atom-thick layer of carbon atoms that are tightly packed in a hexagonal pattern. Graphene has numerous applications in the field of electronics, nanotechnology, biotechnology, and energy storage. Introduction: Graphene is an innovative material that has unique properties such as high electrical conductivity, high thermal conductivity, high mechanical strength, and excellent flexibility. The application of graphene has been used to improve the performance of various electronic devices, including touch screens, solar cells, and sensors. Manufacture: Graphene is synthesized through a process called exfoliation, which involves the mechanical or chemical stripping of graphite layers. Graphene production is impacted by factors such as purity, thickness, size, and number of layers. Graphene's unique structure is a result of its single-atom-thick hexagonal lattice structure, which is responsible for its properties. Properties:

Graphene's mechanical strength and flexibility have also enabled the development of flexible electronics and wearable devices. However, some properties of graphene detract from its use. For example, it is hydrophobic, which makes it challenging to disperse in water-based solutions. Its production also has a high cost, which limits its widespread use. Alternatives:

However, these materials are still in the early stages of research, and graphene remains the most promising material in terms of its unique properties and potential applications.

A materials is a substance or thing from which something can be made from, or the stuff needed to make something. Material is an input in production.

Learn More About Materials at https://brainly.com/question/30418755

#SPJ11

In the BPCS (basic process control system) layer for a highly exothermic reaction, we better be sure that the temperature T stays within the allowed range. The measure we protect against an error in the temperature sensor (reading too low) causing a dangerously high temperature could be to install a second temperature sensor that can detect any erroneous reading from the first sensor. This will alert the BPCS system and result in appropriate actions. The failure position of a control valve is selected to yield the safest condition in the process, so for the reactor with exothermic reaction, we should select "fail-open" valve, which will open the valve during a failure, to prevent the reaction from building pressure. This will avoid any catastrophic situation such as a sudden explosion.

In the SIS (safety interlock system to stop/start equipment), the reason why we do not use the same sensor that is used in BPCS is that if there is an issue with the primary sensor, then the secondary sensor, which is in SIS, will not give the same reading as the primary. This will activate the SIS system and result in appropriate action to maintain the safety of the process. In relief system, the goal is usually to achieve reasonable pressure (prevent high pressure or prevent low pressure). The capacity should be for the "worst-case" scenario, the action is automatic (it does not require a person), and it is entirely self-contained (no external power required).

The reason why it needs no electricity is that in case of an emergency like a power cut, the relief valve still must function. Therefore, it has to be self-contained to operate in the absence of any external power.

Learn more about BPCS (basic process control system)

https://brainly.com/question/31798525

#SPJ11

Approximately 0.033482 moles of gas were present during the process of the temperature change.

To find the number of moles of gas present during the process, we can use the ideal gas law:

PV = nRT

where: P is the pressure (1.804E+5 Pa),

V is the volume (0.00476 m³),

n is the number of moles,

R is the ideal gas constant (8.314 J/(mol·K)),

T is the temperature change in Kelvin.

First, we need to convert the temperature change from Celsius to Kelvin:

ΔT = 26.5 °C = 26.5 K

Rearranging the ideal gas law equation to solve for the number of moles:

n = PV / (RT)

Substituting the given values into the equation:

n = (1.804E+5 Pa × 0.00476 m³) / (8.314 J/(mol·K) × 26.5 K)

Simplifying the equation and performing the calculations:

n ≈ 0.0335 mol

Therefore, approximately 0.0335 moles of gas were present during the process.

Read more on the ideal gas law here: https://brainly.com/question/1056445

#SPJ11

The 1.04 pCi activity of 131I in cow's milk near nuclear reactors corresponds to a mass of approximately 8.49 x 10^-4 grams.

To calculate the mass of 131I with an activity of 1.04 pCi (picocuries) per liter, we need to convert the activity to the corresponding mass using the known relationship between radioactivity and mass.

The conversion factor for iodine-131 is approximately 1 Ci (curie) = 3.7 x 10^10 Bq (becquerel). Since 1 pCi = 0.01 nCi = 0.01 x 10^-9 Ci, we can convert the activity to curies:

1.04 pCi = 1.04 x 10^-12 Ci

To convert from curies to grams, we need to know the specific activity of iodine-131, which represents the radioactivity per unit mass. The specific activity of iodine-131 is approximately 4.9 x 10^10 Bq/g.

Using these values, we can calculate the mass of 131I:

(1.04 x 10^-12 Ci) * (3.7 x 10^10 Bq/Ci) * (1 g / 4.9 x 10^10 Bq) ≈ 8.49 x 10^-4 g

Therefore, the mass of 131I with an activity of 1.04 pCi per liter is approximately 8.49 x 10^-4 grams.

You can learn more about nuclear reactors at

https://brainly.com/question/14400638

#SPJ11

1. Living systems require a subset of elements found in the universe, with carbon, hydrogen, oxygen, nitrogen, phosphorus, and sulfur being essential.

2. Matter serves as the building blocks, while energy drives the processes within living organisms.

3. Atoms form chemical bonds to become stable, including covalent, ionic, and hydrogen bonds.

4. Molecular polarity arises from the unequal sharing of electrons due to differences in electronegativity between atoms.

1. The elements that living systems are made out of are relatively common in the universe. There are 118 known elements, but only about 25 of them are essential for life. These elements include carbon, hydrogen, oxygen, nitrogen, phosphorus, and sulfur, among others. While these elements are abundant in the Earth's crust and atmosphere, their concentrations may vary in different environments.

2. Matter and energy are closely related. Matter refers to anything that has mass and occupies space, while energy is the ability to do work or cause change. In living systems, matter serves as the building blocks for various biological structures, such as cells and tissues. Energy is required to drive the chemical reactions and processes that occur within living organisms. The energy needed by living systems is often derived from the breakdown of organic molecules, such as glucose, through processes like cellular respiration.

3. Atoms bond to become more stable. Atoms are composed of a positively charged nucleus surrounded by negatively charged electrons. In order to achieve a stable configuration, atoms may gain, lose, or share electrons with other atoms. This results in the formation of chemical bonds. There are different types of bonds, including covalent bonds, ionic bonds, and hydrogen bonds. Covalent bonds involve the sharing of electrons, while ionic bonds involve the transfer of electrons. Hydrogen bonds are weaker and occur when a hydrogen atom is attracted to an electronegative atom.

4. The cause of molecular polarity is the unequal sharing of electrons between atoms. In a molecule, if the electrons are shared equally, the molecule is nonpolar. However, if the electrons are not shared equally, the molecule becomes polar. This occurs when there is a difference in electronegativity between the atoms involved in the bond. Electronegativity is the ability of an atom to attract electrons towards itself. When there is a greater electronegativity difference, the more electronegative atom will attract the electrons more strongly, resulting in a polar molecule.

To know more about molecular polarity, refer to the link below:

https://brainly.com/question/30357177#

#SPJ11

Answer:

950 neutrons were released during the fusion reaction.

Explanation:

To determine the number of protons released during nuclear fusion, we need to find the difference in the number of protons before and after the fusion reaction.

Let's denote the number of protons in the original element as P, and the number of neutrons as N. We are given that the total number of protons and neutrons (mass number) in the original element is 1500, so we can write the equation:

P + N = 1500 (Equation 1)

After the fusion reaction, two new elements are created. Let's denote the number of protons in the first new element as P1 and the number of neutrons as N1, and the number of protons in the second new element as P2 and the number of neutrons as N2.

We are given that the first new element has a mass number of 1000, so we can write the equation:

P1 + N1 = 1000 (Equation 2)

Similarly, the second new element has a mass number of 475, so we can write the equation:

P2 + N2 = 475 (Equation 3)

During the fusion reaction, excess neutrons are released. The total number of neutrons in the original element is N. After the fusion reaction, the number of neutrons in the first new element is N1, and the number of neutrons in the second new element is N2. Therefore, the number of neutrons released can be expressed as:

N - (N1 + N2) = Excess neutrons (Equation 4)

Now, we need to solve these equations to find the values of P, P1, P2, N1, N2, and the excess neutrons.

From Equation 1, we can express N in terms of P:

N = 1500 - P

Substituting this into Equations 2 and 3, we get:

P1 + (1500 - P1) = 1000

P2 + (1500 - P2) = 475

Simplifying these equations, we find:

P1 = 500

P2 = 425

Now, we can substitute the values of P1 and P2 into Equations 2 and 3 to find N1 and N2:

N1 = 1000 - P1 = 1000 - 500 = 500

N2 = 475 - P2 = 475 - 425 = 50

Finally, we can substitute the values of P1, P2, N1, and N2 into Equation 4 to find the excess neutrons:

N - (N1 + N2) = Excess neutrons

1500 - (500 + 50) = Excess neutrons

1500 - 550 = Excess neutrons

950 = Excess neutrons

It's critical to create a well-rounded training program that includes particular exercises and training tenets in order to increase muscle endurance. here are some effective methods: resistance training, circuit training, active recovery etc.

Resistance Training: Carry out workouts with a greater repetition count while using lower weights or resistance bands. Concentrate on performing compound exercises like squats, lunges, push-ups, and rows that work numerous muscular groups. In order to increase endurance, aim for 12–20 repetitions per set.

Circuit training: Design a series of exercises that concentrate on various muscle groups. Exercises should be performed one after the other with little pause in between. By maintaining an increased heart rate and using various muscular groups, this strategy aids in the development of endurance.

to know more about muscle endurance refer to the link below

https://brainly.com/question/30560112

#SPJ4

Based on the information provided, the temperature of the water to the nearest degree is 55°C.

The temperature, which is related to the heat inside a body can be measured by using a thermometer and by expressing it in degrees either using Celcius degrees or Fahrenheit degrees.

In this case, each of the lines in the thermometer represents 2°C, this means the temperature of the water is above 54°C and right below 55°C. Based on this, this temperature can be rounded to 55°C.

Learn more about the temperature in https://brainly.com/question/7510619

#SPJ1

The concentration of total solids, total volatile solids, total suspended solids, volatile suspended solids, and total dissolved solids in mg/L for the wastewater sample is 0.1 mg/L.

We need to calculate the concentration of total solids, total volatile solids, total suspended solids, volatile suspended solids, and total dissolved solids in mg/L for a wastewater sample collected for testing. The volume required for each test is 50 mL.

We have the following data:

Total solids: 500 mg/L

Total volatile solids: 200 mg/L

Total suspended solids: 300 mg/L

Volatile suspended solids: 100 mg/L

Total dissolved solids: 100 mg/L

To calculate the concentration of each parameter, we can use the following formula:

Concentration = Mass of solids / Volume of sample

Let's calculate the concentration of each parameter:

Total solids: 500 mg/L * 50 mL/500 mg/L = 0.1 mg/L

Total volatile solids: 200 mg/L * 50 mL/200 mg/L = 0.1 mg/L

Total suspended solids: 300 mg/L * 50 mL/300 mg/L = 0.1 mg/L

Volatile suspended solids: 100 mg/L * 50 mL/100 mg/L = 0.1 mg/L

Total dissolved solids: 100 mg/L * 50 mL/100 mg/L = 0.1 mg/L

Therefore, the concentration of total solids, total volatile solids, total suspended solids, volatile suspended solids, and total dissolved solids in mg/L for the wastewater sample is 0.1 mg/L.

To know more about concentration visit: brainly.com/question/17206790

#SPJ11

The final temperature of the mixture, T, will be the average of the initial temperatures of the two gases: T = (T1 + T2) / 2. This result holds true when the volume is isolated, and no heat exchange occurs with the surroundings.

When the diaphragm is removed and the two gases are allowed to mix, they will undergo a process known as thermal equilibration. In this process, the particles of the two gases will interact with each other and exchange energy until they reach a state of thermal equilibrium.

At the initial state (t = 0), the gases are at different temperatures, T1 and T2. As the diaphragm is removed, the particles from both gases will start to collide with each other. During these collisions, energy will be transferred between the particles.

In an isolated volume where no heat exchange occurs with the environment, the total energy of the system (which includes both gases) is conserved. Energy can be transferred between particles through collisions, but the total energy of the system remains constant.

As the particles collide, energy will be transferred from the higher temperature gas (T1) to the lower temperature gas (T2) and vice versa. This energy transfer will continue until both gases reach a common final temperature, denoted as T.

In the process of reaching thermal equilibrium, the energy transfer will occur until the rates of energy transfer between the gases become equal. At this point, the temperatures of the gases will no longer change, and they will have reached a common temperature, which is the final temperature of the mixture.

Mathematically, the rate of energy transfer between two gases can be proportional to the temperature difference between them. So, in the case of two equal volumes of gases with temperatures T1 and T2, the energy transfer rate will be proportional to (T1 - T2). As the gases reach equilibrium, this energy transfer rate becomes zero, indicating that (T1 - T2) = 0, or T1 = T2.

Therefore, the final temperature of the mixture, T, will be the average of the initial temperatures of the two gases: T = (T1 + T2) / 2. This result holds true when the volume is isolated, and no heat exchange occurs with the surroundings.

Learn more about  thermal equilibrium.

https://brainly.com/question/29419074

#SPJ11

(a) The missing condition in the given set up is the heat source. Heat is required to initiate the reaction between substance X and soda lime, leading to the formation of ethane.

(b) Substance X is likely a halogenated hydrocarbon, such as a halogenalkane or alkyl halide. The chemical formula of substance X would depend on the specific halogen present. For example, if X is chloromethane, the chemical formula would be [tex]CH_{3}Cl[/tex].

(c) Alongside ethane, the reaction would produce a corresponding alkene. In this case, if substance X is chloromethane ([tex]CH_{3} Cl[/tex]), the product formed would be methane and ethene ([tex]C_{2} H_{4}[/tex]).

Alkanes, a class of saturated hydrocarbons, have several practical uses. Three common uses of alkanes are:

1. Fuel: Alkanes, such as methane ([tex]CH_{4}[/tex]), propane ([tex]C_{3}H_{8}[/tex]), and butane (C4H10), are commonly used as fuels. They have high energy content and burn cleanly, making them ideal for heating, cooking, and powering vehicles.

2. Solvents: Certain alkanes, like hexane ([tex]C_{6}H_{14}[/tex]) and heptane ([tex]C_{7} H_{16}[/tex]), are widely used as nonpolar solvents. They are effective in dissolving oils, fats, and many organic compounds, making them valuable in industries such as pharmaceuticals, paints, and cleaning products.

3. Lubricants: Some long-chain alkanes, known as paraffin waxes, are used as lubricants. They have high melting points and low reactivity, making them suitable for applications such as coating surfaces, reducing friction, and protecting against corrosion.

Overall, alkanes play a significant role in various aspects of our daily lives, including energy production, chemical synthesis, and industrial processes.

for such more questions on  chloromethane

https://brainly.com/question/15563498

#SPJ8

The proposed reaction mechanism for the formation of nitrosil bromide, 2NO + BR₂ (G) → 2NOBR (G), follows an elementary speed law and is therefore true.

The intermediary compounds in this reaction mechanism correspond to radicals.

Lastly, the second elementary step does not involve a thermolecular reaction, so it is false.

The global reaction is considered to follow an elementary speed law, which means that the rate-determining step is a single-step process. In this case, the rate-determining step is the first elementary step in the mechanism: NO (G) + BR₂ (G) → NOBR₂. Since this step determines the overall rate of the reaction, the global reaction does follow an elementary speed law.

Intermediary compounds in a reaction mechanism can be ions, molecules, or radicals. In this reaction mechanism, both NOBR2 and NO are considered intermediates. The term "radical" refers to a species with an unpaired electron, making it highly reactive. In the proposed mechanism, both NOBR2 and NO have unpaired electrons, indicating that they are radicals.

The second elementary step in the reaction mechanism is NO (G) + NOBR2 → 2NOBR (G). This step involves the collision and reaction between NO and NOBR2 to form 2NOBR. Since it does not involve three or more molecules colliding simultaneously (thermolecular reaction), it is not considered a thermolecular reaction.

Learn more about speed law

brainly.com/question/29571623

#SPJ11

A chemical process that combines diffusion, convection, and reaction and can be described by a fundamental equation for concentration distribution is the catalytic combustion of a fuel.

In the catalytic combustion of a fuel, diffusion, convection, and reaction all play significant roles. The process involves the reaction of a fuel with oxygen in the presence of a catalyst to produce heat and combustion products. Diffusion refers to the movement of molecules from an area of high concentration to an area of low concentration. In this case, it relates to the transport of fuel and oxygen molecules to the catalyst surface. Convection, on the other hand, involves the bulk movement of fluid, which helps in the transport of heat and reactants to the catalyst surface.

At the catalyst surface, the fuel and oxygen molecules react, resulting in the production of combustion products and the release of heat. The concentration of reactants and products at different points within the system is influenced by the combined effects of diffusion and convection. These processes determine how quickly the reactants reach the catalyst surface and how efficiently the reactions take place.

To describe the distribution of concentrations in this process, a fundamental equation known as the mass conservation equation can be derived. This equation takes into account the diffusion and convection of species, as well as the reactions occurring at the catalyst surface. By solving this equation, it is possible to obtain a quantitative understanding of the concentration distribution throughout the system.

Learn more about diffusion

brainly.com/question/14852229

#SPJ11

a. The mole fraction of A, x_A, can be derived using Fick's second law of diffusion and assuming one-dimensional diffusion in the annular space at steady conditions.

b. The steady-state rate of moles of A sublimated per unit length of the rod is determined by the diffusion flux of A and the catalytic reaction at the inner surface of the larger cylinder in the annular space.

c. The time dependency of the thickness, δ, of the solid S layer can be determined by relating it to the steady-state rate of moles of A sublimated per unit length of the rod and considering the growth of the solid layer over time.

To derive the relation for the mole fraction of A, x_A, we can use Fick's second law of diffusion, which states that the diffusion flux is proportional to the concentration gradient. Assuming one-dimensional diffusion, we can express the diffusion flux of A as -D_AB * (d/dx)(x_A), where D_AB is the diffusion coefficient of A in stagnant air.

Integrating this equation with appropriate boundary conditions, we can obtain the relation for x_A as a function of radial position in the annular space.

The steady-state rate of moles of A sublimated per unit length of the rod is determined by the diffusion flux of A through the annular space and the catalytic reaction occurring at the inner surface of the larger cylinder. The diffusion flux of A can be calculated using Fick's law of diffusion, and the rate of catalytic reaction can be determined based on the stoichiometry of the reaction and the reaction kinetics.

Combining these two rates gives the steady-state rate of moles of A sublimated per unit length of the rod.

The thickness of the layer of solid S, δ, increases with time as a result of the catalytic reaction. Assuming that δ is much smaller than the radius of the larger cylinder (R_2) and neglecting the change in the radius of the smaller cylinder (R_1), we can derive an expression for the time dependency of δ using the result from part (b).

By integrating the steady-state rate of moles of A sublimated per unit length of the rod over time, and considering the density and molecular weight of S, we can determine the time dependency of δ.

Learn more about Diffusion

brainly.com/question/14852229

#SPJ11

a. Fe₂O₃ + 3C → 2Fe + 3CO₂ b. ΔG° = ΔH° - TΔS°

c. Use ideal gas law: PV = nRT to determine partial pressure of CO₂.

To compute the Z-transform of the given sequences and determine the region of convergence (ROC), let's analyze each sequence separately:

1. Sequence: x(k) = 0.5^k * (8^k - 8^(k-2))

The Z-transform of a discrete sequence x(k) is defined as X(z) = ∑[x(k) * z^(-k)], where the summation is taken over all values of k.

Applying the Z-transform to the given sequence, we have:

X(z) = ∑[0.5^k * (8^k - 8^(k-2)) * z^(-k)]

Next, we can simplify the expression by separating the terms within the summation:

X(z) = ∑[0.5^k * 8^k * z^(-k)] - ∑[0.5^k * 8^(k-2) * z^(-k)]

Now, let's compute each term separately:

First term: ∑[0.5^k * 8^k * z^(-k)]

Using the formula for the geometric series, this can be simplified as:

∑[0.5^k * 8^k * z^(-k)] = ∑[(0.5 * 8 * z^(-1))^k]

The above expression represents a geometric series with the common ratio (0.5 * 8 * z^(-1)). For the series to converge, the magnitude of the common ratio should be less than 1, i.e., |0.5 * 8 * z^(-1)| < 1.

Simplifying the inequality gives:

|4z^(-1)| < 1

Solving for z, we find:

|z^(-1)| < 1/4

|z| > 4

Therefore, the region of convergence (ROC) for the first term is |z| > 4.

Second term: ∑[0.5^k * 8^(k-2) * z^(-k)]

Using the same approach, we have:

∑[0.5^k * 8^(k-2) * z^(-k)] = ∑[(0.5 * 8 * z^(-1))^k * z^2]

Similar to the first term, we need the magnitude of the common ratio (0.5 * 8 * z^(-1)) to be less than 1 for convergence. Hence:

|0.5 * 8 * z^(-1)| < 1

Simplifying the inequality gives:

|4z^(-1)| < 1

|z| > 4

Therefore, the ROC for the second term is also |z| > 4.

Combining the ROCs of both terms, we find that the overall ROC for the sequence x(k) = 0.5^k * (8^k - 8^(k-2)) is |z| > 4.

2. Sequence: u(k) = 1, k ≥ 0 (unit step sequence)

The unit step sequence u(k) is defined as 1 for k ≥ 0 and 0 otherwise.

The Z-transform of the unit step sequence u(k) is given by U(z) = ∑[u(k) * z^(-k)].

Since u(k) is equal to 1 for all k ≥ 0, the Z-transform becomes:

U(z) = ∑[z^(-k)] = ∑[(1/z)^k]

This is again a geometric series, and for convergence, the magnitude of the common ratio (1

Learn more about partial pressure

brainly.com/question/30114830

#SPJ11