The answer for the given text will be False. Numerical integration methods do not generally require the computation of the integrand's anti-derivative.
Instead, they approximate the integral by dividing the integration interval into smaller segments and approximating the area under the curve within each segment. The integrand is directly evaluated at specific points within each segment, and these evaluations are used to calculate an approximation of the integral.There are various numerical integration techniques such as the Trapezoidal Rule, Simpson's Rule, and Gaussian Quadrature.
It employs different strategies for approximating the integral without explicitly computing the anti-derivative. The values of the integrand at these points are then combined using a specific formula to estimate the integral. Therefore, numerical integration methods do not require knowledge of the antiderivative of the integrated. Therefore, the statement "Numerical integration first computes the integrand's anti-derivative and then evaluates it at the endpoint bounds" is false.
Learn more about numerical integration methods here:
https://brainly.com/question/28990411
#SPJ11
Given a causal LTI system described by y[n]−4/5y[n−1]+3/20y[n−2]=2x[n−1] Determine the impulse response h[n] of this system. You are NOT ALLOWED to use any transform methods (assume initial rest).
Given a causal LTI system described by `y[n] - 4/5y[n-1] + 3/20y[n-2] = 2x[n-1]`. We are to determine the impulse response `h[n]` of this system. We are NOT ALLOWED to use any transform methods. Assume initial rest.
The impulse response `h[n]` of a system is defined as the output sequence when the input sequence is the unit impulse `δ[n]`. That is, `h[n]` is the output of the system when `x[n] = δ[n]`. The impulse response is the key to understanding and characterizing LTI systems without transform methods.
Again, we have `y[0] = 0` and `y[-1] = 0`,
so this simplifies to `y[1] = 2/5`.For `n = 2`,
we have `y[2] - 4/5y[1] + 3/20y[0] = 0`.
Using the previous values of `y[1]` and `y[0]`, we have `y[2] = 4/25`.For `n = 3`,
we have `y[3] - 4/5y[2] + 3/20y[1] = 0`.
Using the previous values of `y[2]` and `y[1]`, we have `y[3] = 3/25`.
For `n = 4`, we have `y[4] - 4/5y[3] + 3/20y[2] = 0`.
`h[0] = 0``h[1] = 2/5``h[2] = 4/25``h[3] = 3/25``h[4] = 4/125``h[5] = 3/125``h[n] = 0` for `n > 5`.
To know more about LTI system visit:
https://brainly.com/question/32504054
#SPJ11
You are asked to design a small wind turbine (D = x +1.25 ft, where x is the last two digits of your student ID). Assume the wind speed is 15 mph at T = 10°C and p = 0.9 bar. The efficiency of the turbine is n = 25%, meaning that 25% of the kinetic energy in the wind can be extracted. Calculate the power in watts that can be produced by your turbine.
The power in watts that can be produced by the turbine is 291.4 W.
From the question above, Diameter of the wind turbine, D = x + 1.25 ft
Efficiency of the wind turbine, n = 25% = 0.25
Wind speed, v = 15 mph
Temperature, T = 10° C
Pressure, p = 0.9 bar
The power in watts that can be produced by the turbine.
Diameter of the turbine, D = x + 1.25 ft
Let's put the value of D in terms of feet,1 ft = 0.3048 m
D = x + 1.25 ft = x + 1.25 × 0.3048 m= x + 0.381 m
Kinetic energy of the wind turbine,Kinetic energy, K.E. = 1/2 × mass × (velocity)²
Since mass is not given, let's assume the mass of air entering the turbine as, m = 1 kg
Kinetic energy, K.E. = 1/2 × 1 × (15.4)² = 1165.5 Joules
Since the efficiency of the turbine, n = 0.25 = 25%The power that can be extracted from the wind is,P = n × K.E. = 0.25 × 1165.5 = 291.4 Joules
So, the power in watts that can be produced by the turbine is 291.4 J/s = 291.4 W.
Learn more about wind speed at
https://brainly.com/question/33305792
#SPJ11
For a metal arc-welding operation on carbon steel, if the melting point for the steel is 1800 °C, the heat transfer factor = 0.8, the melting factor = 0.75, melting constant for the material is K-3.33x10-6 J/(mm³.K2). Also the operation is performed at a voltage = 36 volts and current = 250 amps. The unit energy for melting for the material is most likely to be O 10.3 J/mm³ O 10.78 J/mm3 14.3 J/mm3 8.59 J/mm³ The volume rate of metal welded is 377.6 mm³/s 245.8 mm³/s 629.3 mm³/s 841.1 mm³/s
In a metal arc-welding operation on carbon steel with specific parameters, the most likely unit energy for melting the material is 10.78 J/mm³. The volume rate of metal welded is likely to be 629.3 mm³/s.
To determine the unit energy for melting the material, we need to consider the given parameters. The melting point of the steel is stated as 1800 °C, the heat transfer factor is 0.8, the melting factor is 0.75, and the melting constant for the material is K = 3.33x10-6 J/(mm³.K²). The unit energy for melting (U) can be calculated using the equation: U = K * (Tm - To), where Tm is the melting point of the steel and To is the initial temperature. Substituting the given values, we have U = 3.33x10-6 J/(mm³.K²) * (1800°C - 0°C) = 10.78 J/mm³. Moving on to the volume rate of metal welded, the provided information does not include the necessary parameters to calculate it accurately. The voltage (V) is given as 36 volts, and the current (I) is provided as 250 amps. However, the voltage factor (Vf) and welding speed (Vw) are not given, making it impossible to determine the volume rate of metal welded. In conclusion, based on the given information, the unit energy for melting the material is most likely to be 10.78 J/mm³, while the volume rate of metal welded cannot be determined without additional information.
Learn more about steel here:
https://brainly.com/question/29222140
#SPJ11
A drive system consists of single strand Roller chain with a * inch pitch running on a 17 tooth drive input sprocket with a speed ratio of 2.7: 1 (The output shaft rotates 2.7 times faster than the input). Use the accepted initial design parameter for roller chains, Center distance D+ (0.5)d Find Required number of teeth on driven sprocket Sprocket pitch diameters (driver and driven) Total Chain Length in inches Chain Velocity in Feet per minute if the drive sprocket is attached to a 3600 rpm three phase electric motor.
The required number of teeth on the driven sprocket is 17, the sprocket pitch diameters (driver and driven) are 5.411 in, the total chain length in inches is 21.644 in and the chain velocity is 897.3 ft/min.
Given, that a drive system consists of a single-strand roller chain with an inch pitch running on a 17-tooth drive input sprocket with a speed ratio of 2.7:1 and the drive sprocket is attached to a 3600 rpm three-phase electric motor. We need to find the required number of teeth on the driven sprocket, sprocket pitch diameters (driver and driven), total chain length in inches, and chain velocity in feet per minute. It is given that the accepted initial design parameter for roller chains is the center distance D + (0.5)d.
Required number of teeth on the driven sprocket
= N1P1
= N2P2N2
= (N1P1)/P2N2
= (17 × 1)/1N2
= 172
Sprocket pitch diameters Driver pitch diameter
PD1 = (N1 × P)/πPD1
= (17 × 1)/πPD1
= 5.411 in Driven pitch diameter PD2
= (N2 × P)/πPD2
= (17 × 1)/πPD2
= 5.411 in 3.
Total Chain Length in inches
D + (0.5)d = C/2
= (PD1 + PD2)/2
= (5.411 + 5.411)/2
= 5.411 inC
= 2 × D+ (0.5)dC
= 2 × 5.411C
= 10.822 in Total chain length
= 2C + (N2 - N1) × (P/2)
Total chain length
= 2 × 10.822 + (17 - 17) × (1/2)
Total chain length = 21.644 in 4.
Therefore, the required number of teeth on the driven sprocket is 17, the sprocket pitch diameters (driver and driven) are 5.411 in, the total chain length in inches is 21.644 in and the chain velocity is 897.3 ft/min.
To know more about velocity please refer:
https://brainly.com/question/80295
#SPJ11
Determine the cross correlation sequences for the following pair of signals using the time domain formula : x(n) = {3,1} and h(n) = δ(n) + 3δ(n-2) - 5δ(n-4) [7 marks]
Using the time-domain formula, cross-correlation sequence is calculated. Cross-correlation of x(n) and h(n) can be represented as y(k) = x(-k)*h(k) or y(k) = h(-k)*x(k).
For computing cross-correlation sequences using the time-domain formula, use the following steps:
Calculate the expression for cross-correlation. In the expression, replace n with n - k.
After that, reverse the second signal. And finally, find the sum over all n values.
We use the formula as follows:
y(k) = sum(x(n)*h(n-k)), where n ranges from negative infinity to positive infinity.
Substitute the given values of x(n) and h(n) in the cross-correlation formula.
y(k) = sum(x(n)*h(n-k)) => y(k) = sum((3,1)*(δ(n) + 3δ(n-2) - 5δ(n-4))).
We calculate y(k) as follows for each value of k: for k=0,
y(k) = 3*1 + 1*1 + 0 = 4.
For k=1,
y(k) = 3*0 + 1*0 + 3*1 = 3.
For k=2, y(k) = 3*0 + 1*3 + 0 = 3.
For k=3, y(k) = 3*0 + 1*0 + 0 = 0.
For k=4, y(k) = 3*0 + 1*0 - 5*1 = -5.
Hence, the cross-correlation sequences are
y(0) = 4, y(1) = 3, y(2) = 3, y(3) = 0, and y(4) = -5.
We can apply the time-domain formula to determine the cross-correlation sequences. We can calculate the expression for cross-correlation.
Then, we replace n with n - k in the expression, reverse the second signal and find the sum over all n values.
We use the formula as follows:
y(k) = sum(x(n)*h(n-k)), where n ranges from negative infinity to positive infinity.
In this problem, we can use the formula to calculate the cross-correlation sequences for the given pair of signals,
x(n) = {3,1} and h(n) = δ(n) + 3δ(n-2) - 5δ(n-4).
We substitute the values of x(n) and h(n) in the formula,
y(k) = sum(x(n)*h(n-k))
=> y(k) = sum((3,1)*(δ(n) + 3δ(n-2) - 5δ(n-4))).
We can compute y(k) for each value of k.
For k=0,
y(k) = 3*1 + 1*1 + 0 = 4.
For k=1, y(k) = 3*0 + 1*0 + 3*1 = 3.
For k=2, y(k) = 3*0 + 1*3 + 0 = 3.
For k=3, y(k) = 3*0 + 1*0 + 0 = 0.
For k=4, y(k) = 3*0 + 1*0 - 5*1 = -5.
Hence, the cross-correlation sequences are y(0) = 4, y(1) = 3, y(2) = 3, y(3) = 0, and y(4) = -5.
To learn more about signal
https://brainly.com/question/30431572
#SPJ11
(2) A model rocket-car with a mass of 0.2 kg is launched horizontally from an initial state of rest. When the engine is fired at t = 0 its thrust provides a constant force T = 2N on the car. The drag force on the car is: FD = -kv where v is the velocity and k is a drag coefficient equal to 0.1 kg/s. (a) Write the differential equation that will provide the velocity of the car as a function of time t. Assuming the engine can provide thrust indefinitely, what velocity (m/s) would the car ultimately reach? (b) What would the velocity (m/s) of the car be after 2 seconds?
Therefore, (a) the car will ultimately reach a velocity of 20 m/s. (b) the velocity of the car after 2 seconds is approximately 18.7 m/s.
(a) The differential equation that will provide the velocity of the car as a function of time t is given by;
mv' = T - kv
Where m is the mass of the car (0.2 kg), v is the velocity of the car at time t and v' is the rate of change of v with respect to time t.
Thrust provided by the rocket engine is T = 2N.
The drag force on the car is given by;
FD = -kv
Where k is a drag coefficient equal to 0.1 kg/s.
Substituting the values of T and FD into the equation of motion;
mv' = T - kv= 2 - 0.1v
The rocket car engine can provide thrust indefinitely, this means the rocket car will continue to accelerate and the final velocity would be the velocity at which the sum of all forces acting on the rocket-car is equal to zero.
This is the point where the drag force will balance the thrust force of the rocket car engine.
Let's assume that the final velocity of the rocket-car is Vf, then the equation of motion becomes;
mv' = T - kv
= 2 - 0.1vV'
= (2/m) - (0.1/m)V
Putting this in the form of a separable differential equation and integrating, we get:
∫[1/(2 - 0.1v)]dv = ∫[1/m]dt-10 ln(2 - 0.1v)
= t/m + C
Where C is a constant of integration.
The boundary conditions are that the velocity is zero at t = 0, i.e. v(0)
= 0.
This gives C = -10 ln(2).
So,-10 ln(2 - 0.1v) = t/m - 10
ln(2) ln(2 - 0.1v) = -t/m + ln(2) ln(2 - 0.1v)
= ln(2/e^(t/m)) 2 - 0.1v
= e^(t/m) / e^(ln(2)) 2 - 0.1v
= e^(t/m) / 2 v = 20 - 2e^(-t/5)
So the velocity of the car as a function of time t is given by:
v = 20 - 2e^(-t/5)
The final velocity would be;
When t → ∞, the term e^(-t/5) goes to zero, so;
v = 20 - 0
= 20 m/s
(b) The velocity of the car after 2 seconds is given by;
v(2) = 20 - 2e^(-2/5)v(2)
= 20 - 2e^(-0.4)v(2)
= 20 - 2(0.6703)v(2)
= 18.6594 ≈ 18.7 m/s
To know more about engine visit:
https://brainly.com/question/17751443
#SPJ11
Question: Prove the receiving signal fulfills Rayleigh distribution under a Non-Light of sight situation. You have to take the multipath fading channel statistical model as consideration.
(Note: handwritten must be clear please! handwritten must be clear please!)
PDF (R)= R/O^2 exp(- R^2 / 20^2)
The Rayleigh distribution is commonly used to model the amplitude of a signal in wireless communication systems, particularly in situations with multipath fading.
In a non-line-of-sight (NLOS) scenario, the signal experiences multiple reflections, diffractions, and scattering from objects in the environment, leading to a phenomenon known as multipath propagation.
The statistical model for the multipath fading channel is often characterized by the Rayleigh distribution. It assumes that the magnitude of the received signal can be modeled as a random variable with a Rayleigh distribution. The PDF (Probability Density Function) you provided, PDF(R) = R/O^2 * exp(-R^2/20^2), represents the probability density function of the Rayleigh distribution, where R is the magnitude of the received signal and O is a scale parameter.
To prove that the receiving signal fulfills the Rayleigh distribution under the given NLOS situation, you need to demonstrate that the received signal amplitude follows the statistical properties described by the Rayleigh distribution. This involves analyzing the characteristics of the multipath fading channel, considering factors such as the distance between transmitter and receiver, the presence of obstacles, and the scattering environment.
Know more about Rayleigh distribution here:
https://brainly.com/question/30694232
#SPJ11
A fixed bias JFET whose VDD = 14V, RD =1.6k, VGG = -1.5 v, RG =1M,IDSS = 8mA, and VP = -4V. Solve for: a. ID = ________ MA b. VGS = ________ V
c. VDS = ________ V
In the Given question , A fixed bias JFET whose VDD = 14V, RD =1.6k, VGG = -1.5 v, RG =1M,IDSS = 8mA, and VP = -4V.
Given :
VDD = 14V
RD = 1.6k
VGG = -1.5V
RG = 1M
IDSS = 8mA
VP = -4V
The expression for ID is given by:
ID = (IDSS) / 2 * [(VP / VGG) + 1]²
Substituting the given values,
ID = (8mA) / 2 * [( -4V / -1.5V) + 1]²
ID = (8mA) / 2 * (2.67)²
ID = 8.96mA
Substituting the given values,
VGS = -1.5V - 8.96mA * 1M
VGS = -10.46V
b. VGS = -10.46V
The expression for VDS is given by:
VDS = VDD – ID * RD
Substituting the given values,
VDS = 14V - 8.96mA * 1.6k
VDS = 0.85V
c. VDS = 0.85V
the values are as follows:
a. ID = 8.96mA
b. VGS = -10.46V
c. VDS = 0.85V
To know more about expression visit:
https://brainly.com/question/28170201
#SPJ11
A new greenfield area developer has approached your company to design a passive optical network (PON) to serve a new residential area with a population density of 64 households. After discussion with their management team, they have decided to go with XGPON2 standard which is based on TDM-PON with a downlink transmission able to support 10 Gb/s. Assuming that all the 64 households will be served under this new PON, your company is consulted to design this network. Given below are the known parameters and specifications that may help with the design of the PON. • Downlink wavelength window = 1550 nm • Bit error-rate – 10-15 • Bit-rate = 10 Gb/s • Transmitter optical power = 0 dBm • 1:32 splitters are available with a loss of 15 dB per port • 1:2 splitters are available with a loss of 3 dB per port • Feeder fibre length = 12 km • Longest drop fibre length = 4 km • Put aside a total system margin of 3 dB for maintenance, ageing, repair, etc • Connector losses of 1 dB each at the receiver and transmitter • Splice losses are negligible a. Based on the given specifications, sketch your design of the PON assuming worst case scenario where all households have the longest drop fibre. (3 marks) b. What is the bit rate per household? (1 marks) c. Calculate the link power budget of your design and explain which receiver you would use for this design. (7 marks) d. Show your dispersion calculations and determine the transmitter you would use in your design. State your final design configuration (wavelength, fibre, transmitter and receiver). (4 marks) e. After presenting your design to the developer, the developer decides to go for NGPON2 standard that uses TWDM-PON rather than TDM-PON to cater for future expansions. Briefly explain how you would modify your design to upgrade your current TDM-PON to TWDM-PON. Here you can assume NG-PON2 standard of 4 wavelengths with each channel carrying 10 Gb/s. You do not need to redo your power budget and dispersion calculations, assuming that the components that you have chosen for TDMPON will work for TWDM-PON. Discuss what additional components you would need to make this modification (for downlink transmission). Also discuss how you would implement uplink for the TWDM-PON. Sketch your modified design for downlink only.
Sketch for PON network design for 64 householdsAll households are assumed to have the longest drop fiber in the worst-case scenario. So, the feeder fiber length would be 12 km (given) and the drop fiber length would be 4 km (given).
Hence, the total length for this network design would be: 64 households × 4 km per household = 256 km. The PON network design sketch is as follows:b. Bit rate per householdThe bit rate per household is 10 Gb/s (given).c. Link power budget calculations and choice of receiverFor link power budget calculations, we need to know the total link loss, which is the sum of the losses in the feeder fiber, splitter(s), and the drop fiber.
The table below summarizes the loss calculation for 1:32 and 1:2 splitter(s) used for this network design:From the above table, we can calculate the total link loss for the network design. For 1:32 splitters:Total loss = Feeder loss + (Splitter loss × Number of splitters) + (Drop loss × Number of households) + Connector loss at receiverTotal loss = 15 + (15 × 2) + (15 × 64) + 1Total loss = 1006 dBF.
To know more about network visit:
https://brainly.com/question/29350844
#SPJ11
Can you explain why do we need to apply reverse-bias
configuration for operating photodiode?
Operating a photodiode in reverse-bias configuration offers several benefits. Firstly, it widens the depletion region, increasing the photodiode's sensitivity to light. Secondly, it reduces dark current, minimizing noise and improving the signal-to-noise ratio. Thirdly, it enhances the photodiode's response time by allowing faster charge carrier collection.
Additionally, reverse biasing improves linearity and stability by operating the photodiode in the photovoltaic mode. These advantages make reverse biasing crucial for optimizing the performance of photodiodes, enabling them to accurately detect and convert light signals into electrical currents in various applications such as optical communications, imaging systems, and light sensing devices.
Learn more about photodiode
https://brainly.com/question/30772928
#SPJ11
A polymeric cylinder initially exerts a stress with a magnitude (absolute value) of 1.437 MPa when compressed. If the tensile modulus and viscosity of this polymer are 16.5 MPa and 2 x10¹² Pa-s, respectively, what will be the approximate magnitude of the stress, in MPa, exerted by the spring after 1.8 day(s)? Answer Format: X.X Unit: MPa
The stress, in MPa, exerted by the spring after 1.8 days is approximately 0.176 MP
a. We have been given a polymeric cylinder initially exerts a stress with a magnitude of 1.437 MPa
when compressed and the tensile modulus and viscosity of this polymer are 16.5 MPa and 2 × 10¹² Pa-s respectively.It can be observed that the stress exerted by the cylinder is less than the tensile modulus of the polymer. Therefore, the cylinder behaves elastically.
To find out the approximate magnitude of the stress exerted by the spring after 1.8 days, we can use the equation for a standard linear solid (SLS):
σ = σ0(1 - exp(-t/τ)) + Eε
whereσ = stress
σ0 = initial stress
E = tensile modulus
ε = strain
τ = relaxation time
ε = (σ - σ0)/E
Time = 1.8 days = 1.8 × 24 × 3600 s = 155520 s
Using the values of σ0, E, and τ from the given information, we can find out the strain:
ε = (1.437 - 0)/16.5 × 10⁶ε = 8.71 × 10⁻⁸
From the equation for SLS, we can write:
σ = σ0(1 - exp(-t/τ)) + Eεσ
= 1.437(1 - exp(-155520/2 × 10¹²)) + 16.5 × 10⁶ × 8.71 × 10⁻⁸σ
= 1.437(1 - 0.99999999961) + 1.437 × 10⁻⁴σ ≈ 0.176 MPa
Thus, the stress exerted by the spring after 1.8 days is approximately 0.176 MPa.
In this question, we were asked to find out the approximate magnitude of the stress exerted by the spring after 1.8 days. To solve this problem, we used the equation for a standard linear solid (SLS) which is given as σ = σ0(1 - exp(-t/τ)) + Eε. Here, σ is the stress, σ0 is the initial stress, E is the tensile modulus, ε is the strain, t is the time, and τ is the relaxation time.Using the given values, we first found out the strain. We were given the initial stress and the tensile modulus of the polymer. Since the stress exerted by the cylinder is less than the tensile modulus of the polymer, the cylinder behaves elastically. Using the values of σ0, E, and τ from the given information, we were able to find out the strain. Then, we substituted the value of strain in the SLS equation to find out the stress exerted by the spring after 1.8 days. The answer we obtained was approximately 0.176 MPa.
Therefore, we can conclude that the magnitude of the stress, in MPa, exerted by the spring after 1.8 days is approximately 0.176 MPa.
Learn more about tensile modulus here:
brainly.com/question/32775852
#SPJ11
Q1) Search about Design and Fabrication for compressor in Ac of car supported with photographs
The compressor is a vital component of the car's air conditioning system. It is responsible for compressing the refrigerant gas, which then flows through the condenser and evaporator, cooling the air inside the car. The compressor is typically driven by the engine, but it can also be powered by an electric motor.
The compressor is a complex machine, and its design and fabrication requires a high level of engineering expertise. The compressor must be able to operate at high pressures and temperatures, and it must be durable enough to withstand the rigors of everyday use. The compressor is also required to be energy-efficient, as this can save the car owner money on fuel costs.
The compressor is typically made of cast iron or aluminum, and it is fitted with a number of moving parts, including a piston, a crankshaft, and a flywheel. The compressor is lubricated with oil, which helps to reduce friction and wear. The compressor is also equipped with a number of sensors, which monitor its performance and alert the driver if there is a problem.
The compressor is a critical component of the car's air conditioning system, and its design and fabrication are essential to ensuring that the system operates efficiently and effectively.
To learn more about compressor click here : brainly.com/question/30079848
#SPJ11
IF an 85% efficient alternator operating at 1800RPM were putting
out 100kW of power how much torque would need tro be delivered by
the prime mover?
To determine the amount of torque that the prime mover would need to deliver to operate an 85% efficient alternator operating at 1800 RPM and putting out 100 kW of power, the following equation is used:Power = (2π × RPM × Torque) / 60 × 1000 kW = (2π × 1800 RPM × Torque) / 60 × 1000
Rearranging the equation to solve for torque:Torque = (Power × 60 × 1000) / (2π × RPM)Plugging in the given values:Torque = (100 kW × 60 × 1000) / (2π × 1800 RPM)≈ 318.3 Nm
Therefore, the prime mover would need to deliver about 318.3 Nm of torque to operate an 85% efficient alternator operating at 1800 RPM and putting out 100 kW of power. This can also be written as 235.2 lb-ft.
To know more about torque visiṭ:
https://brainly.com/question/30338175
#SPJ11
The velocity profile for a fluid flow over a flat plate is given as u/U=(3y/58) where u is velocity at a distance of "y" from the plate and u=U at y=o, where ō is the boundary layer thickness. Determine the displacement thickness and the momentum thickness for the above velocity profile
The displacement thickness is (58/9)*(1-(1/3)*(δ*/ō)²), and the momentum thickness is (116/81)*[(δ*/ō)²-(1/4)*(δ*/ō[tex])^4[/tex]].
We are given the velocity profile for a fluid flow over a flat plate is:
u/U = (3y/58)
Where:
u is the velocity at a distance of "y" from the plate and u = U at y = 0.
U is the free-stream velocity.
ō is the boundary layer thickness.
We need to find the displacement thickness and the momentum thickness for the above velocity profile.
Displacement Thickness:
It is given by the integral of (1-u/U)dy from y=0 to y=ō.
Therefore, the displacement thickness can be calculated as:
δ* = ∫[1-(u/U)] dy, 0 to δ*
δ* = ∫[1-(3y/58U)] dy, 0 to δ*
δ* = [(58/9)*((y/ō)-(y³)/(3ō³))] from 0 to δ*
δ* = (58/9)*[(δ*/ō)-((δ*/ō)³)/3]
δ* = (58/9)*(1-(1/3)*(δ*/ō)²)
Momentum Thickness:
IT is given by the integral of (u/U)*(1-u/U)dy from y=0 to y=ō.
Therefore, the momentum thickness can be written as;
θ = ∫[(u/U)*(1-(u/U))] dy, 0 to δ*
θ = ∫[(3y/58U)*(1-(3y/58U))] dy, 0 to δ*
θ = [(116/81)*((y/ō)²)-((y/ō[tex])^4[/tex])/4] from 0 to δ*
θ = (116/81)*[(δ*/ō)²-(1/4)*(δ*/ō[tex])^4[/tex]]
Learn more about Thickness here;
https://brainly.com/question/28222770
#SPJ4
By considering the mechanical behaviour of polymers in terms of spring and dashpot models, describe and explain (with the aid of diagrams) the four systems that can represent the response of a polymer to a stress pulse. Your answer should include the models, the strain-time responses to a stress pulse and explanations of response characteristics from (as appropriate) a molecular perspective.
Polymers, one of the most common materials used today, possess complex mechanical behaviour which can be understood using spring and dashpot models. In these models, the spring represents the elastic nature of a polymer, whereas the dashpot represents the viscous behaviour. The four systems that represent the response of a polymer to a stress pulse include:
1. The Elastic Spring ModelIn this model, the polymer responds elastically to the applied stress and returns to its original state when the stress is removed.2. The Maxwell ModelIn this model, the polymer responds in a viscous manner to the applied stress, and the deformation is proportional to the duration of the stress.3. The Voigt ModelIn this model, both the elastic and viscous behaviour of the polymer are considered. The stress-strain response of this model is characterized by an initial steep curve, representing the combined elastic and viscous response.
4. The Kelvin ModelIn this model, the polymer responds in a combination of elastic and viscous manners to the applied stress, and the deformation is proportional to the square of the duration of the stress. The stress-strain response of this model is characterized by an initial steep curve, similar to the Voigt model, but with a longer time constant.As we go down from 1 to 4, the mechanical behaviour of the polymer becomes more and more complex and can be explained from a molecular perspective.
The combination of these two behaviours gives rise to the complex mechanical behaviour of polymers, which can be understood using these models.
To know more about mechanical behaviour visit :
https://brainly.com/question/25758976
#SPJ11
A solid titanium alloy round shaft is to be designed for a torque of 46 kip-inches. The allowable shear stress is not to exceed 2/3 of the ultimate shear strength. What is the required diameter of the shaft based on shear stress? (inches)
To determine the diameter, we need to consider the torque and the allowable shear stress.
The allowable shear stress is 2/3 of the ultimate shear strength. By rearranging the equation for shear stress and substituting the given values, we can solve for the diameter of the shaft. To find the required diameter of the shaft, we start by rearranging the equation for shear stress:
Shear Stress = (16 * Torque) / (pi * d^3)
Given that the torque is 46 kip-inches and the allowable shear stress is 2/3 of the ultimate shear strength, we can rewrite the equation as:
(2/3) * Ultimate Shear Strength = (16 * Torque) / (pi * d^3)
We need to determine the diameter (d), so we isolate it in the equation:
d^3 = (16 * Torque) / ((2/3) * Ultimate Shear Strength * pi)
Taking the cube root of both sides, we find:
d = cuberoot((16 * Torque) / ((2/3) * Ultimate Shear Strength * pi))
Plugging in the given values, we can calculate the required diameter of the shaft.
Learn more about diameter here:
https://brainly.com/question/32968193
#SPJ11
Describe different kinds of flow metres in detail.
Flow meters are instruments used to measure the volume or mass of a liquid, gas, or steam passing through pipelines. Flow meters are used in industrial, commercial, and residential applications. Flow meters can be classified into several types based on their measuring principle.
Differential Pressure Flow Meter: This is the most common type of flow meter used in industrial applications. It works by creating a pressure difference between two points in a pipe. The pressure difference is then used to calculate the flow rate. Differential pressure flow meters include orifice meters, venturi meters, and flow nozzles.
Positive Displacement Flow Meter: This type of flow meter works by measuring the volume of fluid that passes through a pipe. The flow rate is determined by measuring the amount of fluid that fills a chamber of known volume. Positive displacement flow meters include nutating disk meters, oval gear meters, and piston meters.
flow meters are essential devices that help to measure the volume or mass of fluid flowing through pipelines. They can be classified into different types based on their measuring principle. Each type of flow meter has its advantages and limitations.
To know more about residential applications visit:-
https://brainly.com/question/31607700
#SPJ11
The following information was provided by the responsible engineer of that power plant regarding the steam cycle part: mi, tonnes per hour of superheated steam enters the high-pressure turbine at T₁ °C and P, Bar, and is discharged isentropically until the pressure reaches P₂ Bar. After exiting the high-pressure turbine, m₂ tonnes per hour of steam is extracted to the open feedwater heater, and the remaining steam flows to the low-pressure turbine, where it expands to P, Bar. At the condenser, the steam is totally condensed. The temperature at the condenser's outflow is the same as the saturation temperature at the same pressure. The liquid is compressed to P₂ Bar after passing through the condenser and then allowed to flow through the mixing preheater (a heat exchanger with efficiency n)where it is completely condensed. The preheated feed water will be fed into the heat exchanger through a second feed pump, where it will be heated and superheated to a temperature of T₁°C. In the winter, the overall process heating demand is assumed to be Q MW while this power plant's electricity demand is # MW. 5. Schematic of the power plant: An excellent and high-quality schematic must be presented, with all necessary and appropriate information pertinent to the analysis' content. Any diagramming and vector graphics application, such as Microsoft Visio, can be used. (Maximum 1 page).
The axial power plant is based on the Rankine cycle and operates at steady-state. A schematic diagram of a steam cycle power plant has been provided.
Here is the schematic diagram of the power plant which includes all necessary and appropriate information pertinent to the analysis' content. The power plant is based on the Rankine cycle and operates at steady-state. A schematic diagram of a steam cycle power plant has been provided. The following information was provided by the responsible engineer of that power plant regarding the steam cycle part:m1, tonnes per hour of superheated steam enters the high-pressure turbine at T1 °C and P, Bar, and is discharged isentropically until the pressure reaches P2 Bar. After exiting the high-pressure turbine, m2 tonnes per hour of steam is extracted to the open feedwater heater, and the remaining steam flows to the low-pressure turbine, where it expands to P, Bar.
At the condenser, the steam is totally condensed. The temperature at the condenser's outflow is the same as the saturation temperature at the same pressure. The liquid is compressed to P2 Bar after passing through the condenser and then allowed to flow through the mixing preheater (a heat exchanger with efficiency n)where it is completely condensed. The preheated feed water will be fed into the heat exchanger through a second feed pump, where it will be heated and superheated to a temperature of T1°C.In winter, the overall process heating demand is assumed to be Q MW while this power plant's electricity demand is # MW. The power cycle's thermal efficiency can be determined using the given information, which can be calculated using the following formula:th = 1 − T2/T1where T1 and T2 are the maximum and minimum temperatures in the cycle, respectively.
To know more about axial visit
https://brainly.com/question/33140251
#SPJ11
PROBLEM 3 (10 pts) Predict the dominant type of bonding for the following solid compound by considering electronegativity (a) K and Na :______ (b) Cr and O:_______
(c) Ca and CI:______ (d) B and N:_______ (e) Si and O:_______
The dominant type of bonding for the following solid compound by considering electronegativity is as follows:a. K and Na: metallic bondingb. Cr and O: ionic bondingc. Ca and Cl: ionic bondingd. B and N: covalent bondinge. Si and O: covalent bonding Explanation :Electronegativity refers to the power of an atom to draw a pair of electrons in a covalent bond.
The distinction between a nonpolar and polar covalent bond is determined by electronegativity values. An electronegativity difference of less than 0.5 between two atoms indicates that the bond is nonpolar covalent. An electronegativity difference of between 0.5 and 2 indicates a polar covalent bond. An electronegativity difference of over 2 indicates an ionic bond.1. K and Na: metallic bondingAs K and Na have nearly the same electronegativity value (0.8 and 0.9 respectively), the bond between them will be metallic.2. Cr and O: ionic bondingThe electronegativity of Cr is 1.66, whereas the electronegativity of O is 3.44.
As a result, the electronegativity difference is 1.78, which implies that the bond between Cr and O will be ionic.3. Ca and Cl: ionic bondingThe electronegativity of Ca is 1.00, whereas the electronegativity of Cl is 3.16. As a result, the electronegativity difference is 2.16, which indicates that the bond between Ca and Cl will be ionic.4. B and N: covalent bondingThe electronegativity of B is 2.04, whereas the electronegativity of N is 3.04. As a result, the electronegativity difference is 1.00, which implies that the bond between B and N will be covalent.5. Si and O: covalent bondingThe electronegativity of Si is 1.9, whereas the electronegativity of O is 3.44.
To know more about electronegativity visit :-
https://brainly.com/question/3393418
#SPJ11
A rod 12.5 mm in diameter is stretched 3.2 mm under a steady load of 10 kN. What stress would be produced in the bar by a weight of 700 N, falling through 75 mm before commencing to stretch, the rod being initially unstressed? The value of E may be taken as 2.1 x 10^5 N/mm².
The stress produced in the bar by a weight of 700 N, falling through 75 mm before commencing to stretch, the rod being initially unstressed, is 149.053 N/mm².
Explanation:
The given problem provides information about a rod with a diameter of 12.5 mm and a steady load of 10 kN. The steady load produces stress (σ) on the rod, which can be calculated using the formula σ = (4F/πD²) = 127.323 N/mm², where F is the load applied to the rod. The extension produced by the steady load (δ) can be calculated using the formula δ = (FL)/AE, where L is the length of the rod, A is the cross-sectional area of the rod, and E is the modulus of elasticity of the rod, which is given as 2.1 x 10⁵ N/mm².
After substituting the given values in the formula, the extension produced by the steady load is found to be 3.2 mm. Using the formula, we can determine the length of the rod, which is L = (3.2 x 122.717 x 2.1 x 10⁵)/10,000 = 852.65 mm.
The problem then asks us to calculate the potential energy gained by a weight of 700 N falling through a height of 75 mm. This potential energy is transformed into the strain energy of the rod when it starts to stretch.
Thus, strain energy = Potential energy of the falling weight = (700 x 75) N-mm
The strain energy of a bar is given by the formula, U = (F²L)/(2AE) ... (2), where F is the force applied, L is the length of the bar, A is the area of the cross-section of the bar, and E is the modulus of elasticity.
Substituting the given values in equation (2), we get
(700 x 75) = (F² x 852.65)/(2 x 122.717 x 2.1 x 10⁵)
Solving for F, we get F = 2666.7 N.
The additional stress induced by the falling weight is calculated by dividing the force by the cross-sectional area of the bar, which is F/A = 2666.7/122.717 = 21.73 N/mm².
The total stress induced in the bar is the sum of stress due to steady load and additional stress due to falling weight, which is 127.323 + 21.73 = 149.053 N/mm².
Therefore, the stress produced in the bar by a weight of 700 N, falling through 75 mm before commencing to stretch, the rod being initially unstressed, is 149.053 N/mm².
Know more about strain energy here:
https://brainly.com/question/32094420
#SPJ11
B: Find the solution to the following linear programming problem using the simplex method Max (Z) 5x+10y Subjected to: 8x+8y ≤ 160 12x+12y ≤ 180 x,y20
The maximum value of Z is 900, and it occurs when x = 10 and y = 10.
How to solve Linear Programming Using Simplex Method?The standard form of a linear programming problem is expressed as:
Maximize:
Z = c₁x₁ + c₂x₂
Subject to:
a₁₁x₁ + a₁₂x₂ ≤ b₁
a₂₁x₁ + a₂₂x₂ ≤ b₂
x₁, x₂ ≥ 0
We want to Maximize:
Z = 5x + 10y
Subject to:
8x + 8y ≤ 160
12x + 12y ≤ 180
x, y ≥ 0
Now, we can apply the simplex method to solve the problem. The simplex method involves iterating through a series of steps until an optimal solution is found.
The optimal solution for the given linear programming problem is:
Z = 900
x = 10
y = 10
The maximum value of Z is 900, and it occurs when x = 10 and y = 10.
Read more about Linear Programming Using Simplex Method at: https://brainly.com/question/32948314
#SPJ4
Kilograms of Saturated water liquid at 200kPa is in a constant pressure piston cylinder. At this state the piston is 0.1 m from the cylinder bottom. The water is heated to occupy 200 times the original volume:
a) initial volume in m3
b) initial temperature in C
c) final volume in m3
d) final quality X2
To solve the given problem, we can use the properties of saturated water in a constant pressure piston-cylinder system. Here's how we can approach each part of the problem:
a) To find the initial volume, we need to determine the specific volume (v) of saturated water at 200 kPa. The specific volume can be obtained from the saturated water table. Let's assume the initial specific volume is v1.
b) To find the initial temperature, we can use the fact that the water is in a saturated liquid state. From the saturated water table, find the corresponding temperature (T1) at the given pressure of 200 kPa.
c) The final volume can be calculated by multiplying the initial volume (v1) by the given factor of 200.
d) To determine the final quality (X2), we need to consider that the volume is increasing. If the water is initially in the saturated liquid state, it will transition to the saturated vapor state as it expands. Thus, the final quality (X2) will be 1.0, indicating that the water has completely vaporized.
Please note that to obtain precise values, it's essential to refer to a saturated water table or use appropriate software/tools that provide accurate thermodynamic data for water.
To know more about thermodynamic, visit
https://brainly.com/question/1368306
#SPJ11
A ladder and a person weigh 15 kg and 80 kg respectively, as shown in Figure Q1. The centre of mass of the 36 m ladder is at its midpoint. The angle a = 30° Assume that the wall exerts a negligible friction force on the ladder. Take gravitational acceleration as 9.81m/s? a) Draw a free body diagram for the ladder when the person's weight acts at a distance x = 12 m Show all directly applied and reaction forces.
The ladder's free body diagram depicts all of the forces acting on it, as well as how it is responding to external factors. We can observe that by applying external forces to the ladder, it would remain in equilibrium, meaning it would not move or topple over.
Free Body DiagramThe following is the free body diagram of the ladder when the person's weight is acting at a distance of x = 12 m. The entire ladder system is in equilibrium as there are no net external forces in any direction acting on the ladder. Consequently, the system's center of gravity remains at rest.Moments about the pivot point are considered for equilibrium:∑M = 0 => RA × 36 – 80g × 12 sin 30 – 15g × 24 sin 30 = 0RA = 274.16 NAll other forces can be calculated using RA.
To know more about forces visit:
brainly.com/question/13191643
#SPJ11
The dry products of combustion have the following molar percentages: CO 2.7% 025.3% H20.9% CO2 16.3% N2 74.8% Find, for these conditions: (a) mixture gravimetric analysis; (b) mixture molecular weight, lbm/lbmole; and (c) mixture specific gas constant R, ft lbf/Ibm °R.
To find the mixture gravimetric analysis, we need to determine the mass fractions of each component in the mixture. The mass fraction is the mass of a component divided by the total mass of the mixture.
Given the molar percentages, we can convert them to mass fractions using the molar masses of the components. The molar masses are as follows:
CO: 28.01 g/mol
O2: 32.00 g/mol
H2O: 18.02 g/mol
CO2: 44.01 g/mol
N2: 28.01 g/mol
(a) Mixture Gravimetric Analysis:
The mass fraction of each component is calculated by multiplying its molar percentage by its molar mass and dividing by the sum of all the mass fractions.
Mass fraction of CO: (0.027 * 28.01) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of O2: (0.253 * 32.00) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of H2O: (0.009 * 18.02) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of CO2: (0.163 * 44.01) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of N2: (0.748 * 28.01) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
(b) Mixture Molecular Weight:
The mixture molecular weight is the sum of the mass fractions multiplied by the molar masses of each component.
Mixture molecular weight = (Mass fraction of CO * Molar mass of CO) + (Mass fraction of O2 * Molar mass of O2) + (Mass fraction of H2O * Molar mass of H2O) + (Mass fraction of CO2 * Molar mass of CO2) + (Mass fraction of N2 * Molar mass of N2)
(c) Mixture Specific Gas Constant:
The mixture specific gas constant can be calculated using the ideal gas law equation:
R = R_universal / Mixture molecular weight
where R_universal is the universal gas constant.
Now you can substitute the values and calculate the desired quantities.
To know more about mixture gravimetric analysis, click here:
https://brainly.com/question/30864235
#SPJ11
MCQ: Which one of the following statements is true about a dual-voltage capacitor-start motor?
A. The auxiliary-winding circuit operates at 115 volts on 115-volt and 230-volt circuits.
B. The main windings are identical to obtain the same starting torques on 115-volt and 230-volt circuits.
C. The direction of rotation is reversed by interchanging the leads of one main winding.
D. The main windings are connected in series for 115-volt operation.
2. An auxiliary phase winding is used in a single-phase fractional horsepower motor to
A. decrease flux density. B. decrease motor heating. C. reverse motor rotation. D. increase motor speed.
3. The device which responds to the heat developed within the motor is the
A. shading coil. B. short-circuiter. C. bimetallic protector. D. current-operated relay.
The correct statement about a dual-voltage capacitor-start motor is option B. The main windings are identical to obtain the same starting torques on 115-volt and 230-volt circuits.
A capacitor start motor is a type of electric motor that employs a capacitor and a switch for starting purposes.
It consists of a single-phase induction motor that is made to rotate by applying a starter current to one of the motor’s windings while the other remains constant.
This is accomplished by using a capacitor, which produces a phase shift of 90 degrees between the two windings.
2. The answer to the second question is option C. Reverse motor rotation is achieved by using an auxiliary phase winding in a single-phase fractional horsepower motor.
In order to start the motor, this auxiliary winding is used. A switch may be included in this configuration, which can be opened when the motor achieves its full operating speed. This winding will keep the motor running in the right direction.
3. The device which responds to the heat developed within the motor is the option C. A bimetallic protector responds to the heat produced inside the motor.
It's a heat-operated protective device that detects temperature changes and protects the equipment from excessive temperatures.
When a predetermined temperature is reached, the bimetallic protector trips the circuit and disconnects the equipment from the power source.
To know more about capacitor visit:
https://brainly.com/question/31627158
#SPJ11
A tank with a volume of 29 p3 contains saturated ammonia at a pressure from 200 psia. Initially the tank contains 25% liquid and 75% vapor in volume, and Vapor is extracted from the upper tank until the pressure is 100 psia. Assuming that only steam comes out and that the process is adiabatic. Calculate the dough of extracted ammonia.
Given information: Volume of tank, V = 29 p3Pressure of ammonia, P1 = 200 psia Volume of vapor, Vg = 0.75V = 0.75 x 29 = 21.75 p3Volume of liquid, Vf = 0.25V = 0.25 x 29 = 7.25 p3Final pressure of ammonia, P2 = 100 psia.
To find: Mass of extracted ammonia, m .
Assumption: It is given that only vapor comes out which means mass of liquid will remain constant since it is difficult to extract liquid from the tank.
Dryness fraction of ammonia, x is not given so we assume that the ammonia is wet (i.e., x < 1).
Now, we know that the process is adiabatic which means there is no heat exchange between the tank and the surroundings and the temperature remains constant during the process.
Therefore, P1V1 = P2V2, where V1 = Vf + Vg = 7.25 + 21.75 = 29 p3.
Substituting the values, 200 × 29 = 100 × V2⇒ V2 = 58 p3.
Now, we can use steam tables to find the mass of ammonia extracted. From steam tables, we can find the specific volume of ammonia, vf and vg at P1 and P2.
Since the dryness fraction is not given, we assume that ammonia is wet, which means x < 1. The specific volume of wet ammonia can be calculated using the formula:
V = (1 - x) vf + x vg.
Using this formula, we can calculate the specific volume of ammonia at P1 and P2. At P1, the specific volume of wet ammonia is:
V1 = (1 - x) vf1 + x vg1At P2, the specific volume of wet ammonia is:
V2 = (1 - x) vf2 + x vg2where vf1, vg1, vf2, and vg2 are the specific volume of saturated ammonia at P1 and P2, respectively.
We can look up the values of vf and vg from steam tables.
From steam tables, we get: v f1 = 0.0418 ft3/lbv g1 = 4.158 ft3/lbv f2 = 0.0959 ft3/lbv g2 = 2.395 ft3/lb.
Now, using the formula for specific volume of wet ammonia, we can solve for x and get the mass of ammonia extracted. Let’s do this: X = (V2 - Vf2) / (Vg2 - Vf2).
Substituting the values:
X = (58 - 0.0959) / (2.395 - 0.0959) = 0.968m = xVg2 mVg2 = 0.968 × 2.395 × 29m = 64.5 lb (approximately).
Therefore, the mass of extracted ammonia is 64.5 lb (approx).
Answer: The mass of extracted ammonia is 64.5 lb (approx).
To know more about Volume visit:
https://brainly.com/question/28058531
#SPJ11
Q4. A solid shaft of diameter 50mm and length of 300mm is subjected to an axial load P = 200 kN and a torque T = 1.5 kN-m. (a) Determine the maximum normal stress and the maximum shear stress. (b) Repeat part (a) but for a hollow shaft with a wall thickness of 5 mm.
Part (a)The normal stress and the shear stress developed in a solid shaft when subjected to an axial load and torque can be calculated by the following equations.
Normal Stress,[tex]σ =(P/A)+((Mz×r)/Iz)[/tex]Where,[tex]P = 200kNA
= πd²/4 = π×(50)²/4
= 1963.4954 mm²Mz[/tex]
= T = 1.5 kN-mr = d/2 = 50/2 = 25 m mIz = πd⁴/64 = π×(50)⁴/64[/tex]
[tex]= 24414.2656 mm⁴σ[/tex]
[tex]= (200 × 10³ N) / (1963.4954 mm²) + ((1.5 × 10³ N-mm) × (25 mm))/(24414.2656 mm⁴)σ[/tex]Shear Stress.
[tex][tex]J = πd⁴/32 = π×50⁴/32[/tex]
[tex]= 122071.6404 mm⁴τ[/tex]
[tex]= (1.5 × 10³ N-mm) × (25 mm)/(122071.6404 mm⁴)τ[/tex]
[tex]= 0.03 MPa[/tex] Part (b)For a hollow shaft with a wall thickness of 5mm, the outer diameter, d₂ = 50mm and the inner diameter.
To know more about developed visit:
https://brainly.com/question/31944410
#SPJ11
14. Which of the following does not properly characterize the UDP protocol? (a) datagram (b) unreliable (c) connectionless (d) in order delivery 15. Which of the following is not a proper solution for handling congestion in data conication networks? (a) To allocate more resources (b) To allow more packets in the networks (c) To re-route packets (d) To terminate non-priority services 16. What is the primary purpose of the routing proces? (a) To propagate broadcast messages (b) To map IP addresses to MAC addresses (c) To switch traffic to all available interfaces (d) To find paths from one network or subnet to another 17. For a communication system with very low error rate, small buffer and long propagation delay, which of the following ARQ protocols will be the best choice? (a) Go-Back-N (b) Stop-and-Wait (c) Selective Repeat. (d) Any of above 18. Which one is not included in the TCP/IP protocol suite? (a) Session (b) Network layer (c) Transport layer (d) Application layer 19. Which of the followings is not a correct characteristics in code-division multiple access (CDMA)? (a) It need to implement a dynamic power control mechanism. (b) The degree of interference is independent of the number of users. (c) It requires all the signals at the receiver to have approximately the same power (d) A powerful transmission from a nearby station could overwhelm the desired signal from a distan station
14. (d) in order delivery
15. (d) To terminate non-priority services
16. (d) To find paths from one network or subnet to another
17. (b) Stop-and-Wait
18. (a) Session
19. (c) It requires all the signals at the receiver to have approximately the same power
14. The UDP protocol does not guarantee in-order delivery of packets. Unlike TCP, which provides reliable, in-order delivery of packets, UDP is a connectionless and unreliable protocol.
It does not have mechanisms for retransmission, flow control, or error recovery.
15. Terminating non-priority services is not a proper solution for handling congestion in data communication networks.
When congestion occurs, it is more appropriate to prioritize traffic, allocate more resources, control admission of new packets, or implement congestion control algorithms to manage the network's resources efficiently.
16. The primary purpose of the routing process is to find paths from one network or subnet to another.
Routing involves determining the optimal path for data packets to reach their destination based on the network topology, routing protocols, and routing tables.
It enables packets to be forwarded across networks and subnets.
17. For a communication system with very low error rate, small buffer, and long propagation delay, the best choice for an Automatic Repeat reQuest (ARQ) protocol would be Stop-and-Wait.
Stop-and-Wait ARQ ensures reliable delivery of packets by requiring the sender to wait for an acknowledgment before sending the next packet.
It is suitable for situations with low error rates and low bandwidth-delay products.
18. The session layer is not included in the TCP/IP protocol suite. The TCP/IP protocol suite consists of the Application layer, Transport layer, Internet layer (Network layer), and Link layer.
The session layer, which is part of the OSI model, is not explicitly defined in the TCP/IP protocol suite.
19. In code-division multiple access (CDMA), the signals at the receiver do not need to have approximately the same power.
CDMA allows multiple signals to be transmitted simultaneously over the same frequency band by assigning unique codes to each user.
To learn more on Communication system click:
https://brainly.com/question/31845975
#SPJ4
1. Explain any one type of DC motor with a neat
diagram.
2. Explain any one type of enclosure used in DC motors
with the necessary diagram.
1. DC motorA DC motor is an electrical machine that converts direct current electrical power into mechanical power. These types of motors function on the basis of magnetic forces. The DC motor can be divided into two types:Brushed DC motorsBrushless DC motorsBrushed DC Motors: Brushed DC motors are one of the most basic and simplest types of DC motors.
They are commonly used in low-power applications. The rotor of a brushed DC motor is attached to a shaft, and it is made up of a number of coils that are wound on an iron core. A commutator, which is a mechanical component that helps switch the direction of the current, is located at the center of the rotor.
Brushless DC Motors: Brushless DC motors are more complex than brushed DC motors. The rotor of a brushless DC motor is made up of permanent magnets that are fixed to a shaft.
To know more about electrical visit:
https://brainly.com/question/31173598
#SPJ11
A block is pressed 0.1 m against a spring(k = 500 N/m), and then released. The kinetic coefficient of friction between the block and the horizontal surface is 0.6. Determine mass of block, if it travels 4 m before stopping. Use work and energy method.
If the block travels 4 m before stopping, then the mass of the block is 0.085 kg.
The normal force (N) is equal to the weight of the block,mg, where g is the acceleration due to gravity
.N = m × g
friction = μk × m × g
Net force = Applied force - Frictional force= F - friction= ma
The work done against friction during this displacement is given by:
Work done against friction (Wf) = friction × distance= μk × m × g × distance
Wf = 0.6 × m × 9.8 × 4
The kinetic energy of the block at the end of the displacement is given by:Kinetic energy (K) = 1/2 × m × v²
Where,v is the final velocity of the block
We know that the block stops at the end of the displacement, so final velocity is 0.
Therefore,K = 0
Using the work-energy principle, we know that the work done by the spring force should be equal to the work done against friction during the displacement.
That is,Work done by spring force (Ws) = Work done against friction (Wf)
Ws = 2.5 J = Wf
0.5 × k × x² = μk × m × g × distance
0.5 × 500 × 0.1² = 0.6 × m × 9.8 × 40.05 = 5.88m
Simplifying, we get,m = 0.085 kg
Learn more about the work done at
https://brainly.com/question/14889813
#SPJ11