Answer:
28Nm
Explanation:
Torque is expressed as the prduct of force and radius
Given
Force = 140N
radius = 0.20m
Torque = 140 * 0.2
Torque = 140 * 1/5
Torque = 28Nm
Hence the amouunt of torque applied is 28Nm
You have just learned that the planet core of Mars is no longer radiating heat like the core of Earth. With this information what would you communicate to building designers as the lead geologist in regards to suitable building locations on the surface of Mars? Remember your informing builders about locations that would best avoid natural disasters like marsquakes and volcanoes? What evidence or theories do you have to support your statements?
Answer:
Explanation:
That is a fun question!
Without a hot radiating core like Earth, Mars will have very different geological and seismic events. The Mars core will be relatively cold and there will not be any molten magma. So Mars will not have earthquakes or volcano activities. Both only occur when there is magma flowing or tectonic plate motion and they will not occur with a cold core.
What would happen to the distance between the bright fringes produced by a diffraction grating if the entire interference apparatus (light source, grating, and screen) were immersed in water
Answer:
Since the wavelength would be reduced by the factor of N where N is the index of refraction, fringes would be be closer to one another.
(Similar to the difference of fringes of red light and blue light.)
A student said,Today, giraffes have long necks that allow them to eat leaves high in trees. They got longer necks by stretching up for even higher leaves. After many generations, the giraffe’s neck was really long.Do you think the student’s explanation for how the giraffe’s neck became long is correct? Explain.
Answer:
yes because there is also a theory about this I studied in biology
theory name -Lamarck's theory
An aluminum-alloy rod has a length of 10.0 cm at 20°C and a length of 10.015 cm at the boiling point of water (1000C). (a) What is the length of the rod at the freezing point of water (0 0C)? (b) What is the temperature if the length of the rod is 10.009 cm? /4mks
Answer:
a. 9.99625 cm b. 68 °C
Explanation:
(a) What is the length of the rod at the freezing point of water (0 0C)?
Before we find the length of the rod, we need to find the coefficient of linear expansion, α = (L - L₀)/[L₀(T - T₀)] where L₀ = length of rod at temperature T₀ = 10.0 cm, T₀ = 20 °C, L = length of rod at temperature T = 10.015 cm and T = 100 °C
Substituting the values of the variables into the equation, we have
α = (L - L₀)/[L₀(T - T₀)]
α = (10.015 cm - 10.0 cm)/[10.0 cm(100 °C - 20 °C)]
α = 0.015 cm/[10.0 cm × 80 °C]
α = 0.015 cm/[800.0 cm °C]
α = 0.00001875 /°C
We now find the length L₁ at T₁ = 0 °C from
L₁ = L₀(1 + α(T₁ - T₀))
So, substituting the values of the variables into the equation, we have
L₁ = L₀(1 + α(T₁ - T₀))
L₁ = 10.0 cm[1 + 0.00001875 /°C(0° C - 20 °C)]
L₁ = 10.0 cm[1 + 0.00001875 /°C × -20° C]
L₁ = 10.0 cm[1 - 0.000375]
L₁ = 10.0 cm[0.999625]
L₁ = 9.99625 cm
(b) What is the temperature if the length of the rod is 10.009 cm?
With length L₃ = 10.009 cm at temperature T₃, using
L₃ = L₀(1 + α(T₃ - T₀))
making T₃ subject of the formula, we have
L₃/L₀ = 1 + α(T₃ - T₀)
L₃/L₀ - 1 = α(T₃ - T₀)
T₃ - T₀ = (L₃/L₀ - 1)/α
T₃ = T₀ + (L₃/L₀ - 1)/α
substituting the values of the variables into the equation, we have
T₃ = 20 °C + (10.009 cm/10.0 cm - 1)/0.00001875 /°C
T₃ = 20 °C + (1.0009 - 1)/0.00001875 /°C
T₃ = 20 °C + 0.0009/0.00001875 /°C
T₃ = 20 °C + 48 °C
T₃ = 68 °C
Q:
The kinetic energy of an object can be determined
using the equation KE = 1/2mv^2, where ke is the
kinetic energy, m is the mass, and v is the speed of
the object. What is the mass of an object moving at
a speed of 12m/s that has 36 J of kinetic energy?
A:
0
2.0 kg
8.0 kg
0.13 kg
0.50 kg
Answer:
Explanation:
We will use the KE equation you wrote here and fill in what we are given:
[tex]36=\frac{1}{2}m(12)^2[/tex] and isolating the m:
[tex]m=\frac{2(36)}{12^2}[/tex] which gives us
m = .50 kg
La resistividad de cierto alambre es 1.72x10 -8 Ωm a 20 oC .Una batería de 6v se conecta a una bobina de 20 m de este alambre, con un diámetro de 0.8 mm. ¿Cuál es la corriente en el alambre?
Answer:
i = 1.09 10⁴ A
Explanation:
For this exercise we will look for the resistance of the wire
R = ρ L / a
the area of the wire is
a =ππ r² = π πd² / 4
we substitute
R = ρ L 4 / π d²
R = 1.72 10⁻⁸ 20 4/π 8 10⁻⁴
R = 5.47 10⁻⁴ Ω
to calculate the current we use ohm's law
V = R i
i = V / R
i = 6 / 5.47 10⁻⁴
i = 1.09 10⁴ A
Pop up spring Lab
Describe the energy conversion that took place. What energy was present just before the jump? What energy is present at its maximum height? What happens in between?
Draw bar charts of energy before the jump, while the spring toy is compressed and after the jump at the maximum height of its jump. Be sure to label each type of energy.
Answer:
I honestly don't know but that thing looks cool lol
Which is a valid ionic compound?
sodide chlorine
sodium chlorine
sodium chloride
sodide chloride
Answer:
sodium chloride
Explanation:
Sodium chloride is an ionic compound. The ions of the sodium chloride compound is sodium ion and chloride ion. The sodium ion is cation while the chloride ion is an anion. Sodium chloride is a very stable compound because of the mutual attraction of oppositely charged ions.
Give your answer to 2 dp
When taking off a plane accelerates at 2.7m/s2 down the runway. It accelerates from a stationary position for 25 seconds before leaving the ground. What
is the planes speed when it leaves the ground?
Answer:
67.5
Explanation:
The plane accelerates at 2.7m/s,^2
Time is 25 seconds
The velocity can be calculated as follows
= 25×2.7
= 67.5
Hence the speed f the plane is 67.5
A parallel combination of 3ohms and 4ohms resistor is connected in series with a resistor of 4ohms and a battery of negligible resistance. Calculate the effective resistance in the circuit
Answer:
Explanation:
Equivalent resistance of parallel combination of two resistors of 3 ohms and 4 ohms .
R₁ = 3 x 4 / ( 3 + 4 )
= 12 / 7 = 1.7 ohms .
This equivalent resistance is connected with 4 ohms in series
Total resistance = 1.7 ohms + 4 ohms
= 5.7 ohms.
Hence effective resistance of the circuit = 5.7 ohms .
Which object will take the most force
to accelerate? *
4 kg
6 kg
8 kg
02 kg
Answer:
I think it might be 8kg grams because it is bigger
Two charges, each q, are separated by a distance r, and exert mutual attractive forces of F on each other. If both charges become 2q and the distance becomes 3r, what are the new mutual forces
Answer:
F = ⅔ F₀
Explanation:
For this exercise we use Coulomb's law
F = k q₁q₂ / r²
let's use the subscript "o" for the initial conditions
F₀ = k q² / r²
now the charge changes q₁ = q₂ = 2q and the new distance is r = 3 r
we substitute
F = k 4q² / 9 r²
F = k q² r² 4/9
F = ⅔ F₀
What are the si units
Answer:
The uniy which is accepted all over the world is called SI unit.
Explanation:
The system of measurement that is agreed by the international convention if scientists that is held in paris of France to adopt an international unit is called SI unit unit.
Transformar las siguientes unidades al Sistema Internacional: 30 km/h ; 37 Dm ; 750 g ; 4x10-6 km2 ; 7500 cm ; 600000 cm2 ; 520700000 mm3 ; 3,4 años.
Answer:
a) 3.0 10⁴ m / s, b) 3.7 10¹ m, c) 0.750 kg, d) 4 10¹² m², e) 75 m, f) 60 m²
g) 5.207 10³ m², e) 4.847 10⁷ s
Explanation:
The international system (SI) of measurements has as fundamental units the meter for length, the second for time and kilogram for mass.
Let's reduce the different magnitudes to the SI system
a) 30 km / h (1000m / 1 km) (1 h / 3600 s) = 3.0 10⁴ m / s
b) 37 Dm (10 m / 1 Dm) = 3.7 10¹ m
c) 750 g (1 kg / 10,000 g) = 0.750 kg
d) 4 10⁶ km² (1000 m / 1km) ² = 4 10¹² m²
e) 7500 cm (1 m / 100 cm) = 75 m
f) 600000 cm² (1m / 10² cm) ² = 60 m²
g) 520700000 mm³ (1 m / 10³ mm) ³ = 5.20700000 109/10 ^ 6
= 5.207 10³ m²
e) 3.4 years (l65 days / 1 yr) (24 h / 1 day) (3600 s / 1h) = 4.847 10⁷ s
Describe how to determine the thickness of a sheet of a paper without a caliper.
Answer:
Divide the total measurement of the stack/ream of paper by the number of sheets. For example: 2 inches/100 pages = 0.01-inches sheets.
In case you measured the stack, and it gave you less than an inch, then you need to do the same. For example: 0.5-inches/100 sheets = 0.005-inches per sheet.
Answer:
Divide the total measurement of the stack/ream of paper by the number of sheets. For example: 2 inches/100 pages = 0.01-inches sheets.
In case you measured the stack, and it gave you less than an inch, then you need to do the same. For example: 0.5-inches/100 sheets = 0.005-inches per sheet.
Explanation:
20 POINTS:
Why does the initial hill of a roller coaster need to be steep?
Answer: A roller coaster does not have an engine to generate energy. The climb up the first hill is accomplished by a lift or cable that pulls the train up. This builds up a supply of potential energy that will be used to go down the hill as the train is pulled by gravity
Hope this helps! Good luck with future homework and exams!
A 0.2 kg hockey park is sliding along the eyes with an initial velocity of -10 m/s when a player strikes it with his stick, causing it to reverse its direction and giving it a velocity of +25 m/s the impulse the stick applies to the park is most nearly
Answer:
The impulse applied by the stick to the hockey park is approximately 7 kilogram-meters per second.
Explanation:
The Impulse Theorem states that the impulse experimented by the hockey park is equal to the vectorial change in its linear momentum, that is:
[tex]I = m\cdot (\vec{v}_{2} - \vec{v_{1}})[/tex] (1)
Where:
[tex]I[/tex] - Impulse, in kilogram-meters per second.
[tex]m[/tex] - Mass, in kilograms.
[tex]\vec{v_{1}}[/tex] - Initial velocity of the hockey park, in meters per second.
[tex]\vec{v_{2}}[/tex] - Final velocity of the hockey park, in meters per second.
If we know that [tex]m = 0.2\,kg[/tex], [tex]\vec{v}_{1} = -10\,\hat{i}\,\left[\frac{m}{s}\right][/tex] and [tex]\vec {v_{2}} = 25\,\hat{i}\,\left[\frac{m}{s} \right][/tex], then the impulse applied by the stick to the park is approximately:
[tex]I = (0.2\,kg)\cdot \left(35\,\hat{i}\right)\,\left[\frac{m}{s} \right][/tex]
[tex]I = 7\,\hat{i}\,\left[\frac{kg\cdot m}{s} \right][/tex]
The impulse applied by the stick to the hockey park is approximately 7 kilogram-meters per second.
Explain how frequency and amplitude affect sound vibrations?
Answer:
The larger the amplitude of the waves, the louder the sound. Pitch (frequency) – shown by the spacing of the waves displayed. The closer together the waves are, the higher the pitch of the sound.
Explanation:
Physicist ____ was found to have completely made up some of the data on which his astounding discoveries were made.
Answer:
Jan Hendrik Schön I believe
8× +5+9×+3 how can I solve this
Answer:
collect like terms then add=>8x+9x+5+3
=>8x+9x+5+3=>17x+8
A nucleus with mass number 229 emits a 3.443 MeV alpha particle. Calculate the disintegration energy Q for this process, taking the recoil energy of the residual nucleus into account.
Answer:
3.504 MeV
Explanation:
Given that;[tex]\frac{A}{Z} X ---->\frac{A-4}{Z-2} Y +\alpha + Q[/tex]
Also;
[tex]Q= KE_{\alpha } (M_{Y} + M_{\alpha } /M_{Y[/tex])
Mass number of X = 229
Mass number of Y = 225
Mass number of alpha particles = 4
Kinetic energy of alpha particles = 3.443 MeV
Q = 3.443 MeV (225 + 4/225)
Q= 3.504 MeV
A tank has the shape of an inverted circular cone with height 16m and base radius 3m. The tank is filled with water to a height of 9m. Find the work required to empty the tank by pumping all of the water over the top of the tank. Use the fact that acceleration due to gravity is 9.8 m/sec2 and the density of water is 1000kg/m3. Round your answer to the nearest kilojoule.
Answer:
[tex]W=17085KJ[/tex]
Explanation:
From the question we are told that:
Height [tex]H=16m[/tex]
Radius [tex]R=3[/tex]
Height of water [tex]H_w=9m[/tex]
Gravity [tex]g=9.8m/s[/tex]
Density of water [tex]\rho=1000kg/m^3[/tex]
Generally the equation for Volume of water is mathematically given by
[tex]dv=\pi*r^2dy[/tex]
[tex]dv=\frac{\piR^2}{H^2}(H-y)^2dy[/tex]
Where
y is a random height taken to define dv
Generally the equation for Work done to pump water is mathematically given by
[tex]dw=(pdv)g (H-y)[/tex]
Substituting dv
[tex]dw=(p(=\frac{\piR^2}{H^2}(H-y)^2dy))g (H-y)[/tex]
[tex]dw=\frac{\rho*g*R^2}{H^2}(H-y)^3dy[/tex]
Therefore
[tex]W=\int dw[/tex]
[tex]W=\int(\frac{\rho*g*R^2}{H^2}(H-y)^3)dy[/tex]
[tex]W=\rho*g*R^2}{H^2}\int((H-y)^3)dy)[/tex]
[tex]W=\frac{1000*9.8*3.142*3^2}{9^2}[((9-y)^3)}^9_0[/tex]
[tex]W=3420.84*0.25[2401-65536][/tex]
[tex]W=17084965.5J[/tex]
[tex]W=17085KJ[/tex]
'
'
A bird in flight pushes itself upward with
a 7.28 N force. If the bird is climbing at a
constant rate of 1 m/s (no acceleration),
what is the weight of the bird?
[?] N
Answer:
The weight of the bird is equal to 7.28 N.
Explanation:
The upward force acting on the bird = 7.28 N
The bird is climbing at a constant rate of 1 m/s.
We need to find the weight of the bird.
We know that the weight of an object is the force of gravity acting on it. It can be calculated as follows :
W = mg
In this case, 7.28 N of force is acting on the object. Hence, the weight of the bird is equal to 7.28 N.
A (200 g) of water at (80 °C) is mixed with (100 g)of water at (20 °C). What is the final temperature of the water?
Answer:
60 °C
Explanation:
From the question given above, the following data were obtained:
Mass of 1st sample (M₁) = 200 g
Temperature of 1st sample (T₁) = 80 °C
Mass of 2nd sample (M₂) = 100 g
Temperature of 2nd sample (T₂) = 20 °C
Equilibrium temperature (Tₑ) =?
NOTE: Since the sample are the same, the specific heat capacity is constant.
We can obtain the equilibrium temperature as follow:
Heat lost by 1st = heat gained by the 2nd
M₁C(T₁ – Tₑ) = M₂C(Tₑ – T₂)
Cancel out C
M₁(T₁ – Tₑ) = M₂(Tₑ – T₂)
200 (80 – Tₑ) = 100 (Tₑ – 20)
Clear bracket
16000 – 200Tₑ = 100Tₑ – 2000
Collect like terms
16000 + 2000 = 100Tₑ + 200Tₑ
18000 = 300Tₑ
Divide both side by 300
Tₑ = 18000 / 300
Tₑ = 60 °C
Therefore, the equilibrium temperature (i.e the final temperature) of the mixture is 60 °C.
If a positively charged rod is brought near the knob of a positively charged electroscope, the leaves of the electroscope will...
A) converge, only
B) diverge, only
C) first diverge, then converge
D) first converge, then diverge
Answer:
B
Explanation:
if a positively charged rod is brought near the knob of a neutral electroscope, it will attract some electrons up from the leaves onto the knob. That process causes both of the leaves to be positively charged (excess protons), and the leaves will diverge.
television set changes electrical energy to sound and light energy. In this process, some energy is *
Answer :light
Explanation:
A television set is another device that operates by the transformation of energy. An electrical beam from the back of the television tube strikes a thin layer of chemicals on the television screen, causing them to glow. In this case, electrical energy is converted into light.
A charge Q acts on a point charge to create an electric field. Its strength, measured a distance of 40 cm away is 100 N/C. What is the magnitude of the electric field strength at a distance of 20 cm
Answer:
[tex]E_2=80N/C[/tex]
Explanation:
From the question we are told that:
Initial Distance [tex]d_1=40cm=>0.4m[/tex]
Initial Electric field strength [tex]E_1=100N/C[/tex]
Final Distance [tex]d_2=20cm=>0.20m[/tex]
Generally the equation for Electric field is mathematically given by.
[tex]E=\frac{kq}{d^2}[/tex]
[tex]q=\frac{100*(0.4)^2}{K}[/tex]
Substituting q for [tex]d=20cm[/tex]
[tex]E_2=\frac{k}{0.2}*\frac{100*(0.4)^2}{K}[/tex]
[tex]E_2=80N/C[/tex]
Which statement best describes the Sun Earth-Moon system?
Answer:
A
Explanation:
A. The Moon orbits the Earth, and the Earth-Moon system orbits the Sun
B. The Earth and Moon both orbit the Sun separately
C. The Sun orbits the Earth-Moon system
D. The Moon revolves around Earth but not the Sun
The energy principle states that:
Energy can be destroyed.
Energy can be created.
Energy cannot be created or destroyed.
Energy cannot be created, but it can be destroyed.
brainleist to correct answer
The energy principle states that:
[tex]\sf\purple{Energy \:cannot \:be \:created \:or\: destroyed.✅}[/tex]
Law of conservation of energy or the first law of thermodynamics states that energy can neither be created nor destroyed; it can only be transferred or changed from one form to another.[tex]\large\mathfrak{{\pmb{\underline{\orange{Happy\:learning }}{\orange{.}}}}}[/tex]