In the early days of networking, the most common way to transmit data was via ____, dial-up telephone lines.a. directly-connected b. sharedc. linkedd. switched

Port numbers are used by NAT overloading to identify each local host. Because of this, the method is also known as port address translation (PAT).

Therefore, the Standard Public IP address assigned to the NAT gateway will remain dedicated to it and cannot be used by another device unless you unassign or delete it. To convert a large number of unregistered IP addresses into a smaller number of registered ones, use dynamic NAT. With the aid of dynamic NAT, you are able to use a small number of registered addresses to connect to numerous hosts on the open Internet. After a certain amount of inactivity, the entry times out, and new translations can be made using the global IP address.

Learn more about addresses here-

https://brainly.com/question/16011753

#SPJ4

Since the network analyst is setting up a wireless access point for a home office in a remote, rural location. The option that the network analyst should enable to meet the requirement is option 1. MAC address filtering.

A person can be able to stop traffic originating from particular recognized machines or devices using MAC address filtering. The router uses the MAC address of a computer or other networked device to recognize it and decide whether to allow or deny access.

Therefore, as a  network analyst, the use of  MAC filtering is one that is located in the settings under Advanced Settings, Security, Access Control, or a section that is similar to these. The precise location will depend on the router's brand. There are two filtering options available for you to select from.

Learn more about MAC address filtering from

https://brainly.com/question/14527362
#SPJ1

Answer:

todo

Explanation:

in the osi reference model complexities of communication are organized into

Since Jesse,  is a professional graphic designer, The things that she needs are: The latest CPU, a lot of RAM as will fit into the system, as well as a high quality image editor.

An image's resolution is seen as one that determines how much detail it has. Digital images, film images, and other sorts of images all fall under this umbrella phrase. Image detail is increased with "higher resolution." There are numerous ways to gauge image resolution.

Note that using computer software or by hand, graphic designers create visual designs to express ideas that move, educate, and enthrall people. For applications like commercials, brochures, magazines, and reports, they create the overall layout and production design.

Therefore, in the contezt of the question, High-resolution pictures have at least 300 pixel per inch (ppi). This resolution produces high-quality prints and is essentially necessary for everything you wish to print on paper, especially if it will be used to represent your brand or other significant printed items. So She need to go with this.

Learn more about graphic designer from

https://brainly.com/question/28182994
#SPJ1

Tap Search after sliding in from the right edge of the screen. In the search box, File History settings. Choose the network or external device you want to use by selecting Select a drive. Activate File History.

The $OF contains files whose pathnames are too long to be kept on your backup device, according to this answer on answer.microsoft.com. Additionally, File History is still the program Microsoft advises using for file backups even though Backup and Restore is a feature of Windows 10 itself. In stark contrast to Backup and Restore, File History's main function is to enable you to back up individual files rather than producing a full system image.

Learn more about program here-

https://brainly.com/question/14618533

#SPJ4

A map of a database that shows tables and relationships is called Schema.

A database is a structured collection of related data that has been systematically organized and is kept in a way that makes it simple to manage and update. It serves as the central repository for all data, comparable to a library's collection of books spanning a variety of genres. Imagine data as a library.

The data can be set up in a database in the form of a table with rows and columns. The data can be easily located and retrieved whenever necessary by indexing it. With the aid of databases, a large number of websites on the Internet are operated. Database handlers are used to build databases that allow users to access the data using just one set of software applications.

Learn more about database

https://brainly.com/question/518894

#SPJ4

To choose the desired parameters to restrict the activities available in a form, use the Property Sheet.

Use Format Painter to swiftly apply the same formatting to numerous pieces of text or pictures, such as color, font style and size, or border style. Think of it as copying and pasting for formatting. With format painter, you can copy all of the formatting from one object and apply it to another. The DataEntry attribute can be used to determine whether a bound form only allows data entry when it opens. The Data Entry property only controls whether existing records are displayed; it does not affect whether new records can be added.

Learn more about formatting here-

https://brainly.com/question/12420521

#SPJ4

Two circumstances that will switch flood frames from every port except the port on which the frame was received:

The switch will transfer the frames from the port the frames have been acquired on (where Host A is connected) to the port wherein the router is attached. Kind of visitors will a transfer flood out all ports are broadcast and multicast forwarding. Since broadcast packets should be received by all stations at the network, the switch will reap that goal by flooding broadcast packets out all ports besides the port that it was received on, since there's no need to send the packet back to the originating device. Because a switch by no means learns those addresses, it constantly floods the frames that have those addresses because a transfer by no means learns those addresses, it always floods the frames that have those addresses as the destination address.

Learn more about the switch, here https://brainly.com/question/9431503

#SPJ4

Since You need to place an ad for the position. The position is Ad specialist, and the specific skills,  is to have a good knowledge of marketing and ad making. The minimum requirements for the position is  a BSC in advertising and media production or in marketing'

Creative concepts are transformed into advertising campaigns by advertising pros. They could specialize in advertising mediums like print, radio, television, and digital.

The daily management of paid digital marketing initiatives, including paid search, display, and social advertising strategies for B2B and B2C organization, is the responsibility of paid media specialists.

Most jobs are full-time or more. Sales representatives for advertising frequently put in extra hours. This profession has a dismal employment prognosis. The U.S. Bureau of Labor Statistics predicts a drop in employment through 2024.

Hence, People can prove they are experts in internet advertising by showing they have a Go ogle Ads certification and others.

Learn more about advertising from

https://brainly.com/question/1658517
#SPJ1

Python program to know if a list is sorted . Output and code image attached.

def isSorted(lst2):

   for p in range(len(lst2)):

       for z in range(p,len(lst2)):

           #Return false if an item is less than or equal to its successor

           if lst2[p]>lst2[z]:

               return False

   return True

if __name__ == '__main__':

list = [int() for ind0 in range(5)]

ans = str

print("Enter 5 numbers: ")

for d in range(5):

 list[d] = int(input())

ans = isSorted(list)

if (ans):

    print("Yes")

else:

    print("No")

To learn more about sort lists in python see: https://brainly.com/question/20624654

#SPJ4

Select New Database from the context menu by right-clicking Databases. Enter a database name in New Database. Select OK to establish the database using all default values; otherwise, carry out the ensuing optional procedures. Select (...) to choose a different owner to alter the owner name.

Launch MySQL Workbench in administrator mode (Right-click, Run as Admin). To construct the database schema, select File>Create Schema. Click Apply after providing the schema with a name.

Expand the Databases' node in Object Explorer before expanding the database that houses the new table. Right-click your database's Tables node in Object Explorer, and then select New Table.

Therefore, To execute the SQL command that creates the schema, click Apply in the Apply SQL Script to Database window.

Learn more about SQL code here:

https://brainly.com/question/25694408

#SPJ1

The descriptions best fit a normalized table is: "flexible" (Option A). Normalization is the process of structuring data in a database.

This comprises the creation of tables and the establishment of linkages between those tables in accordance with rules aimed to preserve the data while also making the database more adaptable by avoiding redundancy and inconsistent reliance.

Tables are database structures that hold all of the information in a database. Tables logically arrange data in a row-and-column structure comparable to spreadsheets.

Each row represents a distinct record, and each column represents a record field.

Learn more about Database Tables:
https://brainly.com/question/22536427
#SPJ1

The Transport layer of the OSI model operates the TCP protocol. Correct answer: letter A.

The Transport layer of the OSI model is responsible for providing reliable end-to-end communication between two hosts. So, it is responsible for ensuring delivery, data sequencing and error control.

The OSI model consists of seven layers:

Sheryl is explaining the OSI model to new technicians at her company. She is trying to explain what protocols operate at the various layers of the OSI model. At what layer of the OSI model does TCP operate?

A. Transport

B. Application

C. Network

D. Data link

Learn more about the OSI model:

https://brainly.com/question/15901869

#SPJ4

By converting combinations of mnemonics and syntax for operations and addressing modes into their numerical representations, an assembler program generates object code.

The majority of the statements or instructions in assembly language are mnemonic processor instructions or data. It is created by compiling the source code of high-level languages like C and C++. Assembly Language aids in program optimization.

.586

.MODEL FLAT

INCLUDE io.h

.STACK 4096

.DATA

value1 DWORD ?

value2 DWORD ?

"Enter the initial number," prompt1 BYTE, 0

"Enter the second number," prompt2 BYTE, 0

string BYTE 40 DUP (?)

resultLbl BYTE  "The maximum value you entered was:", 0

.CODE

_MainProc PROC      

input prompt1, string, 40       ;get user input value1

atod string                     ;convert input (ASCII) to integer

mov ebx, eax

input prompt2, string, 40   ; repeat for value2

atod string

mov value2, eax

cmp eax, ebx                ;compare user inputs

jg greater_than     ;jump conditional if value 1 is greater then value 2

   greater_than:   ;condition if greater than ouput

       dtoa value1, eax                    ;decimal to ASC for output of

integer value stored at ebx

       output  resultLbl, value1           ;output value 1

           jmp exit                    

   less_than:  ;condition if less than ouput

       dtoa value1, eax

       output  resultLbl, value2           ;else output value 2    

           jmp exit

   exit:   ;quit jump              ;end if/else conditional

   mov eax, 0          ;clear memory

   mov ebx, 0

   ret

_MainProc ENDP

END

assemblyx86

The complete question is

Simple assembly program to spit out the greater of two user input numbers. I am having trouble getting the output correct. Example if I entered 45 and 55, the maximum value would be 55, however when I try the reverse 55 and 45 (the answer should still be 55) I get 45. It would appear that this program only ever outputs the second value entered and stored at EAX. Any help is greatly appreciated.

To learn more about assembler program refer to:

https://brainly.com/question/13171889

#SPJ4

; Set up input/output

movlw 0x00

movwf TRISA

movlw 0x00

movwf TRISB

; Define MAXIMUM macro

MAXIMUM MACRO num1, num2

   movf num1, W

   subwf num2, W

   btfsc STATUS, C

   movf num2, W

   movwf num1

   ENDM

; Main program

main:

   ; Prompt user to enter first number

   movlw 0x31

   call putch

   call getch

   movwf num1

   ; Prompt user to enter second number

   movlw 0x32

   call putch

   call getch

   movwf num2

   ; Find and display larger number

   MAXIMUM num1, num2

   call putch

   ; Repeat

   goto main

It can be inferred that the above task will be executed in Linux because the systemctl utility command is a Linux utility used to manage the sytemd service and the service manager on Linux.

1) In order to install NTP Service first, execute the following command as sudo in order to update your local repository index: "$ sudo apt-get update"

2) Execute this command to install NTP Server daemon from APT database: "$ sudo apt-get install ntp"

3) Next, open the file in the nano editor as sudo by executing the following command: "$ sudo nano /etc/ntp.conf"

4) Restart the NTP Service using the following command line "$ sudo service ntp restart"

To check that the NTP Service is running, execute the following command: "$ sudo service ntp status"

The Network Time Protocol (NTP) is a service that allows system clocks to be synchronized (from desktops to servers). It is not only useful but also needed for many distributed applications to have synchronized clocks. As a result, if the time originates from an external server, the firewall rules must enable the NTP service.

The usage of authentication techniques in Network Time Protocol (NTP) is critical to preventing an attacker from manipulating time information. Such systems have been present for a long time, such as the Symmetric Key-based method and the Autokey approach.

Learn more about NTP Service:
https://brainly.com/question/14857188?
#SPJ1

The average access time for the processor to access an item is 19.5.

Average access time is defined as a standard statistic for evaluating the performance of computer memory systems. Access time is the amount of time it takes for an electronic system to respond to a request and provide the needed data.

Main memory access time = 200 ns

Cache access time = 10 ns

Hit ratio = 0.95

Average access time

= 0.95 x 10 + ( 1 - 0.95 ) x 200

= 9.5 + 0.05 x 200

= 9.5 + 10

= 19.5

Thus, the average access time for the processor to access an item is 19.5.

To learn more about average access time, refer to the link below:

https://brainly.com/question/14287236

#SPJ1

The correct option is E. The following subnet that masks should Joe use for this subnet is /30.

An IP network can be logically divided into subnetworks or subnets. 1, 16 Subnetting is the process of splitting a network into two or more networks.

Similar most-significant bit groups are used in IP addresses to address computers that are on the same subnet. As a result, the network number or routing prefix and the rest field or host identity are logically separated into two fields in an IP address. A host or network interface can be identified by the remainder field.

The Classless Inter-Domain Routing (CIDR) notation allows the routing prefix to be represented as the network's primary address, followed by a slash (/), and the prefix's bit length at the end. To give one example, the prefix is 198.51.100.0/24.

To know more about subnet click here:

https://brainly.com/question/15055849

#SPJ4

All of the above-mentioned are accurate answers as traffic intensity is a measure of network traffic conditions . The distribution of interarrival times the number of customers, system stability, and system congestion are all measured by the traffic intensity.

In order to describe network congestion or other degraded network situations, the level of network traffic is gauged by traffic intensity. When determined, traffic intensity—also known as the traffic intensity factor—describes the state of a packet-switched network, such as one that carries TCP traffic.

The traffic intensity factor a relative measure, takes into account the average packet size, arrival rate, and available network transmission speeds. It can be calculated using the formula below:

The equation for the Traffic intensity factor is:

Traffic intensity factor = La/R

where a = average packet arrival rate; L = average packet size; R = transmission rate.

The Traffic Intensity Factor can be used to guide rate-limiting algorithms, error prediction, and probing for network delays.

To learn more about network traffic click here:

brainly.com/question/9392514

#SPJ4

When maintenance and fixes must be performed concurrently in order for a product to remain effective, this is known as a pre-requisite/co-requisite relationship.

Describe maintenance.

In terms of industrial, commercial, and residential installations, maintenance technically refers to functional inspections, servicing, repairing, or replacing necessary machinery, equipment, and investing in infrastructure. This has evolved over time to encompass varied language that describes different cost-effective maintenance procedures to keep equipment operating; these operations actually occur either before or after a failure. Maintenance is linked primarily to the product or technological system's usage phase, during which the maintainability idea must be taken into account. In this situation, maintainability is understood to be an object's ability to business produces under specified .

To know more about maintenance
https://brainly.com/question/13257907
#SPJ4

The ObjectOutputStream and ObjectInputStream classes can perform this task using the writeObject and readObject methods; Serializable lacks these methods.

The ObjectOutputStream and ObjectInputStream classes can perform this task using the write Object and read Object methods; Serializable lacks these methods. Serializable is merely a marker interface; it doesn't call for any fields or methods; it simply sets a flag. A marker interface called Serializable merely informs JVM that a specific object is set to be serialized. Internally, the serialization process takes place.

interface that is serializable. No state from classes that don't implement this interface will be serialized or desterilized. A class that can be serialized has all of its subtypes be serializable. The only purpose of the serialization interface, which has no methods or fields, is to define the semantics of being serializable.

To know more about serializable click here:

https://brainly.com/question/13326134

#SPJ4

chage -M 60 -W 10 jsmith Forces jsmith to keep the password 60 days before changing it and gives a warning 10 days before changing it.

The "chage" command is used to edit the user's account's password expiration date. It allows you to change the expiration date's current status, set an expiration date to lock the account, toggle between active and passive status, and receive notifications days before the account expires.

The tool to "update user password expiry information" is what the chage command calls itself. The chage man page states: The chage command modifies the last password change date as well as the number of days between password updates.

For additional information on the chage command, see

brainly.com/question/13084023

#SPJ4

Before handling any internal components, disconnect the computer and take the necessary anti-static procedures to safeguard your personal safety.

Regarding graphics

In order to inform, clarify, or amuse, graphics are graphic images or designs on a surface, including a wall, canvas, computer, newspaper, or stone. In modern usage, it refers to a visual visualization of data, such as that used in software for education and entertainment, design and manufacturing, typesetting, and the graphic arts. Computer graphics refers to images created by a computer. Graphics can be aesthetic or useful. The line between the two may become hazy if the latter is a documented form, such as a picture, or an analysis by a scientist to emphasize key characteristics.

To know more about graphics
https://brainly.com/question/11764057
#SPJ4

A company wants to create highly available datacenters. BGP will allow the company to continue to maintain an Internet presence at all sites in the event that a WAN circuit at one site goes down.

BGP (Border Gateway Protocol) is a type of routing protocol that functions to exchange information between Autonomous Systems (AS). This BGP is a Dynamic Routing and on the proxy itself there are several kinds of dynamic routing features other than BGP such as OSPF and RIP. To exchange information, BGP utilizes the TCP protocol so that there is no need to use other types of protocols to handle fragmentation, retransmission, acknowledgment and sequencing.

Learn more about BGP at https://brainly.com/question/9257367.

#SPJ4

The solution to the above prompt with regard to the list named are:

A) dict1 = dict([(list1[i], list2[i]) for i in range(len(list1))])

B) dict1 = {}

for i in range(len(list1)) :

[Tab Key]dict1[list1[i]] = list2[i]

C)

dict1 = dict([(list1[i], list2[i]) for i in range(len(list2))])

A list or sequence is an abstract data type in computer science that contains a finite number of ordered items, where a given value may appear more than once.

The usage of lists is another programming method that will be helpful to our algorithm development because many algorithms need the manipulation of sets of data. Similar to a variable, a list—also known as an array—is a tool for data storage.

Learn more about lists:
https://brainly.com/question/26352522
#SPJ1

A message is encoded by the sender, who then sends it. (3) The message is decoded by the receiver.

The process by which the receiver interprets the symbols used by the message's source is known as decoding. He is the recipient of the communication from the sender. Feedback: Feedback is any behavior by the recipient that shows he has heard and understood the sender's message. The process through which information is conveyed and comprehended by two or more individuals is referred to as communication. Effective communication is about conveying the sender's intended message. The receiver's job is to accurately translate the sender's message, both verbal and nonverbal, into their own language. Decoding is the process of understanding the message.

Learn more about communication here-

https://brainly.com/question/18825060

#SPJ4

1. Some challenges that photographers face when trying to take a great image include:

2. Some elements that separate good images from great images include:

3. The purposes that photographers have for taking photographs include:

4. To capture images with your audience in mind simply means to have the emotions and feelings of the audience in mind.

Photographs are important in everyone's life because they connect us to our past and remind us of people, places, feelings, and stories from our past. They can assist us in determining who we are.

When we talk about capturing the moment in photography, we're really referring to the photo's feeling, emotion, vibe, or atmosphere. That comes from more than just the subjects or the surroundings; it also comes from the photographer.

Learn more about photograph on:

https://brainly.com/question/25821700

#SPJ1

The correct port number that should be used with the WinSCP or Cyberduck secure file transfer program is 22.

A port is a number used in computer networking to designate a connection endpoint and direct data to a particular service. A port is a logical construct that, at the level of software, identifies a particular process or kind of network service within an operating system. Thre are more than 800 ports.

Therefore, WinSCP or Cyberduck secure file transfer programs should be used with port number 22, which is the correct one to use.

To learn more about the file transfer program, refer to the link:

https://brainly.com/question/27380368

#SPJ1

Java program with function calls and list return. An image of the code and output of the algorithm is attached.

import java.util.ArrayList;

import java.util.Scanner;

public class Main {

  public static void main(String[] args) {

     ArrayList<Integer> total_weight = new ArrayList();

     ArrayList<Integer> weight = new ArrayList();

     int N;

     double media;

     N = Numberofpeople();

     dividedintotwoteams(total_weight,weight, N);

     System.out.println("Total weight of team 1 y 2: "+total_weight);

  }

  public static int Numberofpeople() {

     Scanner sc = new Scanner(System.in);

     int n;

 System.out.println("****Divide people into two teams****  ");

 System.out.println("---------------------------------  ");

 System.out.print("Number of people in row: ");

 n = sc.nextInt();

 return n;

  }

public static void dividedintotwoteams(ArrayList<Integer> total_weight, ArrayList<Integer> weight, int n) {

    Scanner sc = new Scanner(System.in);

 int team1, team2, x;

 team1 = 0;

 team2 = 0;

 int w;

 for (x=1;x<=n;x++) {

  System.out.print(x+" person weights: ");

  do {

       w = sc.nextInt();

  } while (w<=0);

  weight.add(w); //add weight to ArrayList

  if (x%2!=0) {

   team1 = team1+w;

  } else {

   team2 = team2+w;

  }

 }

 total_weight.add(team1);

 total_weight.add(team2);

}

}

To learn more about list and functions in java see: https://brainly.com/question/18554491

#SPJ4

They place all network devices for one part of the building physically in the same room, often in a rack of equipment.

To learn more about switched network refer :

https://brainly.com/question/12811608

#SPJ4

Note that where while listening to exam instructions a user reports that she can't connect to a server on your network. you check the problem and find out that all users are having the same problem. What you should  do next is: "Determine what has changed" (Option B)

A computer network is a collection of computers that share resources that are located on or provided by network nodes. To interact with one another, the computers employ standard communication protocols across digital linkages.

Local-area networks (LANs) and wide-area networks (WANs) are the two main network kinds (WANs). LANs connect computers and peripheral devices in a constrained physical space, such as a corporate office, laboratory, or college campus, using data-transmitting connections (wires, Ethernet cables, fiber optics, Wi-Fi).

Learn more about networks:
https://brainly.com/question/15002514
#SPJ1

While listening to exam instructions a user reports that she can't connect to a server on your network. you check the problem and find out that all users are having the same problem. what should you do next?

What should you do next?