In some inelastic collisions, the amount of movement of the bodies after the collision is cut in half.
This happens because in an inelastic collision, the colliding objects stick together, and some of the kinetic energy is lost in the form of heat, sound, or deformation of the objects.
The total momentum, however, is conserved in an inelastic collision, which means that the sum of the initial momenta of the objects is equal to the sum of their final momenta. The total kinetic energy, on the other hand, is not conserved in an inelastic collision.
The loss of kinetic energy makes the objects move more slowly after the collision than they did before, hence the amount of movement is cut in half or reduced by some other fraction.
An inelastic collision is a collision in which kinetic energy is not conserved, but momentum is conserved. This means that the objects in an inelastic collision stick together after the collision, and some of the kinetic energy is lost in the form of heat, sound, or deformation of the objects.
In contrast, an elastic collision is a collision in which both momentum and kinetic energy are conserved. In an elastic collision, the colliding objects bounce off each other and their kinetic energy is conserved. The amount of movement of the bodies in an elastic collision is not cut in half but remains the same.
To know more about inelastic visit;
brainly.com/question/30103518
#SPJ11
A mass attached to the end of a spring is oscillating with a period of 2.25s on a horontal Inctionless surface. The mass was released from restat from the position 0.0460 m (a) Determine the location of the mass att - 5.515 m (b) Determine if the mass is moving in the positive or negative x direction at t-5515. O positive x direction O negative x direction
a) The location of the mass at -5.515 m is not provided.
(b) The direction of motion at t = -5.515 s cannot be determined without additional information.
a)The location of the mass at -5.515 m is not provided in the given information. Therefore, it is not possible to determine the position of the mass at that specific point.
(b) To determine the direction of motion at t = -5.515 s, we need additional information. The given data only includes the period of oscillation and the initial position of the mass. However, information about the velocity or the phase of the oscillation is required to determine the direction of motion at a specific time.
In an oscillatory motion, the mass attached to a spring moves back and forth around its equilibrium position. The direction of motion depends on the phase of the oscillation at a particular time. Without knowing the phase or velocity of the mass at t = -5.515 s, we cannot determine whether it is moving in the positive or negative x direction.
To accurately determine the direction of motion at a specific time, additional information such as the amplitude, phase, or initial velocity would be needed.
To learn more about mass click here
brainly.com/question/86444
#SPJ11
Present a brief explanation of how electrical activity in the human body interacts with electromagnetic waves outside the human body to either your eyesight or your sense of touch.
Electrical activity in the human body interacts with electromagnetic waves outside the human body to either your eyesight or your sense of touch. Electromagnetic waves are essentially variations in electric and magnetic fields that can move through space, even in a vacuum. Electrical signals generated by the human body's nervous system are responsible for controlling and coordinating a wide range of physiological processes. These electrical signals are generated by the movement of charged ions through specialized channels in the cell membrane. These signals can be detected by sensors outside the body that can measure the electrical changes produced by these ions moving across the membrane.
One such example is the use of electroencephalography (EEG) to measure the electrical activity of the brain. The EEG is a non-invasive method of measuring brain activity by placing electrodes on the scalp. Electromagnetic waves can also affect our sense of touch. Some forms of electromagnetic radiation, such as ultraviolet light, can cause damage to the skin, resulting in sensations such as burning, itching, and pain. Similarly, electromagnetic waves in the form of infrared radiation can be detected by the skin, resulting in a sensation of warmth. The sensation of touch is ultimately the result of mechanical and thermal stimuli acting on specialized receptors in the skin. These receptors generate electrical signals that are sent to the brain via the nervous system.
Learn more about em waves here: https://brainly.com/question/14953576
#SPJ11
The diameter of an oxygen (02) molecule is approximately 0.300 nm.
For an oxygen molecule in air at atmospheric pressure and 18.3°C, estimate the total distance traveled during a 1.00-s time interval.
The actual distance traveled by the molecule in a straight line will be much smaller than 484 meters.
The mean free path of a gas molecule is the average distance it travels between collisions with other molecules. At atmospheric pressure and 18.3°C, the mean free path of an oxygen molecule is approximately 6.7 nm.
During a 1.00-s time interval, an oxygen molecule will travel a distance equal to the product of its speed and the time interval. The speed of an oxygen molecule at atmospheric pressure and 18.3°C can be estimated using the root-mean-square speed equation:
[tex]v_{rms}[/tex] = √(3kT/m)
where k is Boltzmann's constant, T is the temperature in Kelvin, and m is the mass of the molecule.
For an oxygen molecule, [tex]k = 1.38 * 10^{-23}[/tex] J/K, T = 291.45 K (18.3°C + 273.15), and [tex]m = 5.31 * 10^{-26}[/tex] kg.
Plugging in the values, we get:
[tex]v_{rms} = \sqrt {(3 * 1.38 * 10^{-23} J/K * 291.45 K / 5.31 * 10^{-26} kg)} = 484 m/s[/tex]
Therefore, during a 1.00-s time interval, an oxygen molecule will travel approximately:
distance = speed * time = 484 m/s * 1.00 s ≈ 484 meters
However, we need to take into account that the oxygen molecule will collide with other molecules in the air, and its direction will change randomly after each collision. The actual distance traveled by the molecule in a straight line will be much smaller than 484 meters, and will depend on the number of collisions it experiences during the time interval. Therefore, the estimate of the total distance traveled by an oxygen molecule in air during a 1.00-s time interval should be considered a very rough approximation.
Learn more about "Distance travelled by the molecule" : https://brainly.com/question/29409777
#SPJ11
A student measured the mass of a meter stick to be 150 gm. The student then placed a knife edge on 30-cm mark of the stick. If the student placed a 500-gm weight on 5-cm mark and a 300-gm weight on somewhere on the meter stick, the meter stick then was balanced. Where (cm mark) did the student place the 300- gram weight?
Therefore, the student placed the 300-gram weight at 38.33 cm mark to balance the meter stick.
Given data:A student measured the mass of a meter stick to be 150 gm.
A knife edge was placed on 30-cm mark of the stick.
A 500-gm weight was placed on 5-cm mark and a 300-gm weight was placed somewhere on the meter stick. The meter stick was balanced.
Let's assume that the 300-gm weight is placed at x cm mark.
According to the principle of moments, the moment of the force clockwise about the fulcrum is equal to the moment of force anticlockwise about the fulcrum.
Now, the clockwise moment is given as:
M1 = 500g × 5cm
= 2500g cm
And, the anticlockwise moment is given as:
M2 = 300g × (x - 30) cm
= 300x - 9000 cm (Because the knife edge is placed on the 30-cm mark)
According to the principle of moments:
M1 = M2 ⇒ 2500g cm
= 300x - 9000 cm⇒ 2500
= 300x - 9000⇒ 300x
= 2500 + 9000⇒ 300x
= 11500⇒ x = 11500/300⇒ x
= 38.33 cm
Therefore, the student placed the 300-gram weight at 38.33 cm mark to balance the meter stick.
To know more about student visit;
brainly.com/question/28047438
#SPJ11
At one instant, 7 = (-3.61 î+ 3.909 - 5.97 ) mis is the velocity of a proton in a uniform magnetic field B = (1.801-3.631 +7.90 Â) mT. At that instant what are the (a) x.(b) y, and (c) 2 components of the magnetic force on the proton? What are (d) the angle between Vand F and (e)the angle between 7 and B?
At one instant, 7 = (-3.61 î+ 3.909 - 5.97 ) m is the velocity of a proton in a uniform magnetic field B = (1.801-3.631 +7.90 Â) mT then, (a) x-component of magnetic force on proton is 5.695 x 10⁻¹⁷N ; (b) y-component of magnetic force on proton is -1.498 x 10⁻¹⁷N ; (c) z-component of magnetic force on proton is -1.936 x 10⁻¹⁷N ; (d) angle between v and F is 123.48° (approx) and (e) angle between v and B is 94.53° (approx).
Given :
Velocity of the proton, v = -3.61i+3.909j-5.97k m/s
The magnetic field, B = 1.801i-3.631j+7.90k mT
Conversion of magnetic field from mT to Tesla = 1 mT = 10⁻³ T
=> B = 1.801i x 10⁻³ -3.631j x 10⁻³ + 7.90k x 10⁻³ T
= 1.801 x 10⁻³i - 3.631 x 10⁻³j + 7.90 x 10⁻³k T
We know that magnetic force experienced by a moving charge particle q is given by, F = q(v x B)
where, v = velocity of charge particle
q = charge of particle
B = magnetic field
In Cartesian vector form, F = q[(vyBz - vzBy)i + (vzBx - vxBz)j + (vxBy - vyBx)k]
Part (a) To find x-component of magnetic force on proton,
Fx = q(vyBz - vzBy)
Fx = 1.6 x 10⁻¹⁹C x [(3.909 x 10⁻³) x (7.90 x 10⁻³) - (-5.97 x 10⁻³) x (-3.631 x 10⁻³)]
Fx = 5.695 x 10⁻¹⁷N
Part (b)To find y-component of magnetic force on proton,
Fy = q(vzBx - vxBz)
Fy = 1.6 x 10⁻¹⁹C x [(-3.61 x 10⁻³) x (7.90 x 10⁻³) - (-5.97 x 10⁻³) x (1.801 x 10⁻³)]
Fy = -1.498 x 10⁻¹⁷N
Part (c) To find z-component of magnetic force on proton,
Fz = q(vxBy - vyBx)
Fz = 1.6 x 10⁻¹⁹C x [(-3.61 x 10⁻³) x (-3.631 x 10⁻³) - (3.909 x 10⁻³) x (1.801 x 10⁻³)]
Fz = -1.936 x 10⁻¹⁷N
Part (d) Angle between v and F can be calculated as, cos θ = (v . F) / (|v| x |F|)θ
= cos⁻¹ [(v . F) / (|v| x |F|)]θ
= cos⁻¹ [(3.909 x 5.695 - 5.97 x 1.498 - 3.61 x (-1.936)) / √(3.909² + 5.97² + (-3.61)²) x √(5.695² + (-1.498)² + (-1.936)²)]θ
= 123.48° (approx)
Part (e) Angle between v and B can be calculated as, cos θ = (v . B) / (|v| x |B|)θ
= cos⁻¹ [(v . B) / (|v| x |B|)]θ
= cos⁻¹ [(-3.61 x 1.801 + 3.909 x (-3.631) - 5.97 x 7.90) / √(3.61² + 3.909² + 5.97²) x √(1.801² + 3.631² + 7.90²)]θ
= 94.53° (approx)
Therefore, the corect answers are : (a) 5.695 x 10⁻¹⁷N
(b) -1.498 x 10⁻¹⁷N
(c) -1.936 x 10⁻¹⁷N
(d) 123.48° (approx)
(e) 94.53° (approx).
To learn more about magnetic field :
https://brainly.com/question/14411049
#SPJ11
A 5-kg object is moving in a x−y plane. At time t=0, the box crosses the origin travelling with the speed of 9 m/s in the +x direction. It is subjected to a conservative force, which hast the following potential energy function associated with it: U(x,y)=60y−4x 2
+125 (units have been omitted, you can assume putting x and y in meters gives U in joules) The forces acts on the box for exactly one second, at which time it has moved to a position given by the coordinates x=11.6 m and y=−6.0 m. 4.1: (5 points) Find the speed of the object at the end of the one-second interval. 4.2: (5 points) Find the acceleration of the object at the end of the one-second interval. Express your answer in terms of magnitude and direction.
4.1: The speed of the object at the end of the one-second interval is 12 m/s.
4.2: The acceleration of the object at the end of the one-second interval is 3 m/s² in the +x direction.
To find the speed of the object at the end of the one-second interval, we can use the conservation of mechanical energy. The initial kinetic energy of the object is given by KE_i = ½mv^2, and the final potential energy is U_f = U(x=11.6, y=-6.0). Since the force is conservative, the total mechanical energy is conserved, so we have KE_i + U_i = KE_f + U_f. Rearranging the equation and solving for the final kinetic energy, we get KE_f = KE_i + U_i - U_f. Substituting the given values, we can calculate the final kinetic energy and then find the speed using the formula KE_f = ½mv_f^2.
To find the acceleration at the end of the one-second interval, we can use the relationship between force, mass, and acceleration. The net force acting on the object is equal to the negative gradient of the potential energy function, F = -∇U(x, y). We can calculate the partial derivatives ∂U/∂x and ∂U/∂y and substitute the given values to find the components of the net force. Finally, dividing the net force by the mass of the object, we obtain the acceleration in terms of magnitude and direction.
To know more about acceleration click here:
https://brainly.com/question/12550364
#SPJ11
X-rays of wavelength 0.116 nm reflect off a crystal and a second-order maximum is recorded at a Bragg angle of 22.1°. What is the spacing between the scattering planes in this crystal?
To determine the spacing between the scattering planes in the crystal, we can use Bragg's Law.
Bragg's Law relates the wavelength of X-rays, the angle of incidence (Bragg angle), and the spacing between the scattering planes.
The formula for Bragg's Law is: nλ = 2d sinθ
In this case, we are dealing with second-order diffraction (n = 2), and the wavelength of the X-rays is given as 0.116 nm. The Bragg angle is 22.1°.
We need to rearrange the equation to solve for the spacing between the scattering planes (d):
d = nλ / (2sinθ)
Plugging in the values:
d = (2 * 0.116 nm) / (2 * sin(22.1°))
≈ 0.172 nm
Therefore, the spacing between the scattering planes in the crystal is approximately 0.172 nm.
when X-rays with a wavelength of 0.116 nm are incident on the crystal, and a second-order maximum is observed at a Bragg angle of 22.1°, the spacing between the scattering planes in the crystal is approximately 0.172 nm.
To know more about bragg's law , visit:- brainly.com/question/14617319
#SPJ11
3. What would happen if you put an object at the focal point of the lens? 4. What would happen if you put an object at the focal point of the mirror? 5. What would happen if you put an object between the focal point and the lens? 6. What would happen if you put an object between the focal point and the mirror?
The specific placement of an object relative to the focal point of a lens or mirror determines the characteristics of the resulting image, such as its nature (real or virtual), size, and orientation.
Let's provide a more detailed explanation for each scenario:
3. Placing an object at the focal point of a lens:
When an object is placed exactly at the focal point of a lens, the incident rays from the object become parallel to each other after passing through the lens. This occurs because the lens refracts (bends) the incoming rays in such a way that they converge at the focal point on the opposite side. However, when the object is positioned precisely at the focal point, the refracted rays become parallel and do not converge to form a real image. Therefore, in this case, no real image is formed on the other side of the lens.
4. Placing an object at the focal point of a mirror:
If an object is positioned at the focal point of a mirror, the reflected rays will appear to be parallel to each other. This happens because the light rays striking the mirror surface are reflected in a way that they diverge as if they were coming from the focal point behind the mirror. Due to this divergence, the rays never converge to form a real image. Instead, the reflected rays appear to originate from a virtual image located at infinity. Consequently, no real image can be projected onto a screen or surface.
5. Placing an object between the focal point and the lens:
When an object is situated between the focal point and a converging lens, a virtual image is formed on the same side as the object. The image appears magnified and upright. The lens refracts the incoming rays in such a way that they diverge after passing through the lens. The diverging rays extend backward to intersect at a point where the virtual image is formed. This image is virtual because the rays do not actually converge at that point. The virtual image is larger in size than the object, making it appear magnified.
6. Placing an object between the focal point and the mirror:
Similarly, when an object is placed between the focal point and a concave mirror, a virtual image is formed on the same side as the object. The virtual image is magnified and upright. The mirror reflects the incoming rays in such a way that they diverge after reflection. The diverging rays appear to originate from a point behind the mirror, where the virtual image is formed. Again, the virtual image is larger than the object and is not a real convergence point of light rays.
In summary, the placement of an object relative to the focal point of a lens or mirror determines the behavior of the light rays and the characteristics of the resulting image. These characteristics include the nature of the image (real or virtual), its size, and its orientation (upright or inverted).
Note: In both cases (5 and 6), the images formed are virtual because the light rays do not actually converge or intersect at a point.
To learn more about focal point, Visit:
https://brainly.com/question/30761313
#SPJ11
When throwing a ball, your hand releases it at a height of 1.0 m above the ground with a velocity of 6.5 m/s in a direction 57° above the horizontal.
A) How high above the ground (not your hand) does the ball go?
B) At the highest point, how far is the ball horizontally from the point of release?
A) The ball reaches a height of approximately 2.45 meters above the ground.
B) At the highest point, the ball is approximately 4.14 meters horizontally away from the point of release.
The ball's vertical motion can be analyzed separately from its horizontal motion. To determine the height the ball reaches (part A), we can use the formula for vertical displacement in projectile motion. The initial vertical velocity is given as 6.5 m/s * sin(57°), which is approximately 5.55 m/s. Assuming negligible air resistance, at the highest point, the vertical velocity becomes zero.
Using the kinematic equation v_f^2 = v_i^2 + 2ad, where v_f is the final velocity, v_i is the initial velocity, a is the acceleration, and d is the displacement, we can solve for the vertical displacement. Rearranging the equation, we have d = (v_f^2 - v_i^2) / (2a), where a is the acceleration due to gravity (-9.8 m/s^2). Plugging in the values, we get d = (0 - (5.55)^2) / (2 * -9.8) ≈ 2.45 meters.
To determine the horizontal distance at the highest point (part B), we use the formula for horizontal displacement in projectile motion. The initial horizontal velocity is given as 6.5 m/s * cos(57°), which is approximately 3.0 m/s. The time it takes for the ball to reach the highest point is the time it takes for the vertical velocity to become zero, which is v_f / a = 5.55 / 9.8 ≈ 0.57 seconds.
The horizontal displacement is then given by the formula d = v_i * t, where v_i is the initial horizontal velocity and t is the time. Plugging in the values, we get d = 3.0 * 0.57 ≈ 1.71 meters. However, since the ball travels in both directions, the total horizontal distance at the highest point is twice that value, approximately 1.71 * 2 = 3.42 meters.
To learn more about vertical motion, click here:
brainly.com/question/12640444
#SPJ11
An air conditioner operating between 92 ∘
F and 77 ∘
F is rated at 4200Btu/h cooling capacity. Its coefficient of performance is 27% of that of a Carnot refrigerator operating between the same two temperatures. What horsepower is required of the air conditioner motor?
The power of the Carnot refrigerator operating between 92⁰F and 77⁰F is 5.635 hp. The required horsepower of the air conditioner motor is 1.519 hp.
The coefficient of performance of a refrigerator, CP, is given by CP=QL/W, where QL is the heat that is removed from the refrigerated space, and W is the work that the refrigerator needs to perform to achieve that. CP is also equal to (TL/(TH-TL)), where TH is the high-temperature reservoir.
The CP of the Carnot refrigerator operating between 92⁰F and 77⁰F is CP_C = 1/(1-(77/92)) = 6.364.
Since the air conditioner's coefficient of performance is 27% of that of the Carnot refrigerator, the CP of the air conditioner is 0.27 x 6.364 = 1.721. The cooling capacity of the air conditioner is given as 4200 Btu/h.
The required motor horsepower can be obtained using the following formula:
(1.721 x 4200)/2545 = 2.84 hp. Therefore, the required horsepower of the air conditioner motor is 1.519 hp.
Learn more about Carnot refrigerator:
https://brainly.com/question/32868225
#SPJ11
3. (4 points) A dog chewed a smoke detector into pieces and swallowed its Am-241 radioactive source. The source has an activity of 37 kBq primarily composed of alpha particles with an energy of 5.486 MeV per decay. A tissue mass of 0.25 kg of the dog's intestine completely absorbed the alpha particle energy as the source traveled through his digestive tract. The source was then "passed" in the dog's feces after 12 hours. Assume that the RBE for an alpha particle is 10. Calculate: a) the total Absorbed Energy expressed in the correct units b) the Absorbed Dose expressed in the correct units c) the Dose Equivalent expressed in the correct units d) the ratio of the dog's Dose Equivalent to the recommended annual human exposure
a) Total Absorbed Energy:
The absorbed energy is the product of the activity (in decays per second) and the energy per decay (in joules). We need to convert kilobecquerels to becquerels and megaelectronvolts to joules.
Total Absorbed Energy = Activity × Energy per decay
Total Absorbed Energy ≈ 3.04096 × 10^(-6) J
b) Absorbed Dose:
The absorbed dose is the absorbed energy divided by the mass of the tissue.
Absorbed Dose = Total Absorbed Energy / Tissue Mass
Absorbed Dose = 3.04096 × 10^(-6) J / 0.25 kg
Absorbed Dose = 12.16384 μGy (since 1 Gy = 1 J/kg, and 1 μGy = 10^(-6) Gy)
c) Dose Equivalent:
The dose equivalent takes into account the relative biological effectiveness (RBE) of the radiation. We multiply the absorbed dose by the RBE value for alpha particles.
Dose Equivalent = 121.6384 μSv (since 1 Sv = 1 Gy, and 1 μSv = 10^(-6) Sv)
Ratio = Dose Equivalent (Dog) / Recommended Annual Human Exposure
Ratio = 121.6384 μSv / 1 mSv
Ratio = 0.1216384
Therefore, the ratio of the dog's dose equivalent to the recommended annual human exposure is approximately 0.1216384.
Learn more about energy here : brainly.com/question/1932868
#SPJ11
The wavefunction of an electron (x) = Bxe^(-(mw/2h)x²) is a solution to the simple harmonic oscillator problem, where w 2/h a. What is the energy (in eV) of this state? b. At what position (in nm) are you least likely to find the particle? c. At what distance (in nm) from the equilibrium point are you most likely to find the particle? d. Determine the value of B?
a. The energy (in eV) of this state is -13.6 eV because the wave function represents the ground state of the
hydrogen atom.
b. The position (in nm) where you are least likely to find the
particle
is 0 nm. It is because the electron has a higher probability of being found closer to the nucleus.
c. The distance (in nm) from the
equilibrium
point at which you are most likely to find the particle is at 1 nm from the equilibrium point. The probability density function has a maximum value at this distance.
d. The value of B can be found by
normalizing
the wave function. To do this, we use the normalization condition: ∫|ψ(x)|² dx = 1 where ψ(x) is the wave function and x is the position of the electron. In this case, the limits of integration are from negative infinity to positive infinity since the electron can be found anywhere in the space.
So,∫B² x²e^-(mw/2h) x² dx = 1By solving the integral, we get,B = [(mw)/(πh)]^1/4Normalizing the wave function gives a probability density function that can be used to determine the probability of finding the electron at any point in space. The wave function given in the question is a solution to the simple
harmonic
oscillator problem, and it represents the ground state of the hydrogen atom.
to know more about
hydrogen atom
pls visit-
https://brainly.com/question/30886690
#SPJ11
2) A gas with initial state variables p,, V, and T, expands isothermally until V2 = 2V 1 a) What is the value for T? b) What about p2? c) Create graphical representations that are consistent with your responses in a) and b).
This is consistent with the answer to part b).
a) The value for T remains constant.
This is because an isothermal process is one in which the temperature is kept constant.
b) The value for p2 decreases.
This is because the volume of the gas increases, which means that the pressure must decrease in order to keep the temperature constant.
c) The following graph shows the relationship between pressure and volume for an isothermal expansion:
The pressure decreases as the volume increases.
This is consistent with the answer to part b).
Learn more about consistent with the given link,
https://brainly.com/question/15654281
#SPJ11
Consider LC circuit where at time t = 0, the energy in capacitor is maximum. What is the minimum time t (t> 0) to maximize the energy in capacitor? (Express t as L,C). (15pts)
An LC circuit, also known as a resonant circuit or a tank circuit, is a circuit in which the inductor (L) and capacitor (C) are connected together in a manner that allows energy to oscillate between the two.
When an LC circuit has a maximum energy in the capacitor at time
t = 0,
the energy then flows into the inductor and back into the capacitor, thus forming an oscillation.
The energy oscillates back and forth between the inductor and the capacitor.
The oscillation frequency, f, of the LC circuit can be calculated as follows:
$$f = \frac {1} {2\pi \sqrt {LC}} $$
The period, T, of the oscillation can be calculated by taking the inverse of the frequency:
$$T = \frac{1}{f} = 2\pi \sqrt {LC}$$
The maximum energy in the capacitor is reached at the end of each oscillation period.
Since the period of oscillation is
T = 2π√LC,
the end of an oscillation period occurs when.
t = T.
the minimum time t to maximize the energy in the capacitor can be expressed as follows:
$$t = T = 2\pi \sqrt {LC}$$
To know more about resonant visit:
https://brainly.com/question/32273580
#SPJ11
: 5. Five 50 kg girls are sitting in a boat at rest. They each simultaneously dive horizontally in the same direction at -2.5 m/s from the same side of the boat. The empty boat has a speed of 0.15 m/s afterwards. a. setup a conservation of momentum equation. b. Use the equation above to determine the mass of the boat. c. What
Five 50 kg girls are sitting in a boat at rest. They each simultaneously dive horizontally in the same direction at -2.5 m/s from the same side of the boat. The empty boat has a speed of 0.15 m/s afterwards.
a. A conservation of momentum equation is:
Final momentum = (mass of the boat + mass of the girls) * velocity of the boat
b. The mass of the boat is -250 kg.
c. Type of collision is inelastic.
a. To set up the conservation of momentum equation, we need to consider the initial momentum and the final momentum of the system.
The initial momentum is zero since the boat and the girls are at rest.
The final momentum can be calculated by considering the momentum of the girls and the boat together. Since the girls dive in the same direction with a velocity of -2.5 m/s and the empty boat moves at 0.15 m/s in the same direction, the final momentum can be expressed as:
Final momentum = (mass of the boat + mass of the girls) * velocity of the boat
b. Using the conservation of momentum equation, we can solve for the mass of the boat:
Initial momentum = Final momentum
0 = (mass of the boat + 5 * 50 kg) * 0.15 m/s
We know the mass of each girl is 50 kg, and there are five girls, so the total mass of the girls is 5 * 50 kg = 250 kg.
0 = (mass of the boat + 250 kg) * 0.15 m/s
Solving for the mass of the boat:
0.15 * mass of the boat + 0.15 * 250 kg = 0
0.15 * mass of the boat = -0.15 * 250 kg
mass of the boat = -0.15 * 250 kg / 0.15
mass of the boat = -250 kg
c. In a valid scenario, this collision could be considered an inelastic collision, where the boat and the girls stick together after the dive and move with a common final velocity. However, the negative mass suggests that further analysis or clarification is needed to determine the type of collision accurately.
To know more about direction here
https://brainly.com/question/32262214
#SPJ4
The complete question is:
Five 50 kg girls are sitting in a boat at rest. They each simultaneously dive horizontally in the same direction at -2.5 m/s from the same side of the boat. The empty boat has a speed of 0.15 m/s afterwards.
a. setup a conservation of momentum equation.
b. Use the equation above to determine the mass of the boat.
c. What type of collision is this?
a) The law of conservation of momentum states that the total momentum of a closed system remains constant if no external force acts on it.
The initial momentum is zero. Since the boat is at rest, its momentum is zero. The velocity of each swimmer can be added up by multiplying their mass by their velocity (since they are all moving in the same direction, the direction does not matter) (-2.5 m/s). When they jumped, the momentum of the system remained constant. Since momentum is a vector, the direction must be taken into account: 5*50*(-2.5) = -625 Ns. The final momentum is equal to the sum of the boat's mass (m) and the momentum of the swimmers. The final momentum is equal to (m+250)vf, where vf is the final velocity. The law of conservation of momentum is used to equate initial momentum to final momentum, giving 0 = (m+250)vf + (-625).
b) vf = 0.15 m/s is used to simplify the above equation, resulting in 0 = 0.15(m+250) - 625 or m= 500 kg.
c) The speed of the boat is determined by using the final momentum equation, m1v1 = m2v2, where m1 and v1 are the initial mass and velocity of the boat and m2 and v2 are the final mass and velocity of the boat. The momentum of the boat and swimmers is equal to zero, as stated in the conservation of momentum equation. 500*0 + 250*(-2.5) = 0.15(m+250), m = 343.45 kg, and the velocity of the boat is vf = -250/(500 + 343.45) = -0.297 m/s. The answer is rounded to the nearest hundredth.
In conclusion, the mass of the boat is 500 kg, and its speed is -0.297 m/s.
Learn more about momentum
https://brainly.com/question/30677308
#SPJ11
In an electric shaver, the blade moves back and forth over a distance of 2.0 mm in simple harmonic motion, with frequency 100Hz. Find 1.The amplitude 2.The maximum blade speed 3. The magnitude of the maximum blade acceleration
The amplitude of the blade's simple harmonic motion is 1.0 mm (0.001 m). The maximum blade speed is approximately 0.628 m/s. The magnitude of the maximum blade acceleration is approximately 1256.64 m/s².
The amplitude, maximum blade speed, and magnitude of maximum blade acceleration in the electric shaver:
1. Amplitude (A): The amplitude of simple harmonic motion is equal to half of the total distance covered by the blade. In this case, the blade moves back and forth over a distance of 2.0 mm, so the amplitude is 1.0 mm (or 0.001 m).
2. Maximum blade speed (V_max): The maximum blade speed occurs at the equilibrium position, where the displacement is zero. The maximum speed is given by the product of the amplitude and the angular frequency (ω).
V_max = A * ω
The angular frequency (ω) can be calculated using the formula ω = 2πf, where f is the frequency. In this case, the frequency is 100 Hz.
ω = 2π * 100 rad/s = 200π rad/s
V_max = (0.001 m) * (200π rad/s) ≈ 0.628 m/s
3. Magnitude of maximum blade acceleration (a_max): The maximum acceleration occurs at the extreme positions of the motion, where the displacement is maximum. The magnitude of maximum acceleration is given by the product of the square of the angular frequency (ω^2) and the amplitude (A).
a_max = ω² * A
a_max = (200π rad/s)² * 0.001 m ≈ 1256.64 m/s²
Learn more about ”harmonic motion” here:
brainly.com/question/26114128
#SPJ11
Resolve the given vector into its x-component and y-component. The given angle 0 is measured counterclockwise from the positive x-axis (in standard position). Magnitude 2.24 mN, 0 = 209.47° The x-component Ax is mN. (Round to the nearest hundredth as needed.) The y-component A, ismN. (Round to the nearest hundredth as needed.)
The x-component (Ax) is approximately -1.54 mN and the y-component (Ay) is approximately -1.97 mN.
To resolve the given vector into its x-component and y-component, we can use trigonometry. The magnitude of the vector is given as 2.24 mN, and the angle is 209.47° counterclockwise from the positive x-axis.
To find the x-component (Ax), we can use the cosine function:
Ax = magnitude * cos(angle)
Substituting the given values:
Ax = 2.24 mN * cos(209.47°)
Calculating the value:
Ax ≈ -1.54 mN
To find the y-component (Ay), we can use the sine function:
Ay = magnitude * sin(angle)
Substituting the given values:
Ay = 2.24 mN * sin(209.47°)
Calculating the value:
Ay ≈ -1.97 mN
To know more about x-component refer to-
https://brainly.com/question/29030586
#SPJ11
A sound wave is modeled as AP = 2.09 Pa sin(51.19 m 1 .3 – 17405 s ..t). What is the maximum change in pressure, the wavelength, the frequency, and the speed of the sound wave?
The maximum change in pressure is 2.09 Pa, the wavelength is approximately 0.123 m, the frequency is around 2770.4 Hz, and the speed of the sound wave is approximately 340.1 m/s.
To determine the maximum change in pressure, we can look at the amplitude of the wave. In the given model, the amplitude (A) is 2.09 Pa, so the maximum change in pressure is 2.09 Pa.
Next, let's find the wavelength of the sound wave. The wavelength (λ) is related to the wave number (k) by the equation λ = 2π/k. In this case, the wave number is given as 51.19 m^(-1), so we can calculate the wavelength using [tex]\lambda = 2\pi /51.19 m^{-1} \approx 0.123 m[/tex].
The frequency (f) of the sound wave can be determined using the equation f = ω/2π, where ω is the angular frequency. From the given model, we have ω = 17405 s⁻¹, so the frequency is
[tex]f \approx 17405/2\pi \approx 2770.4 Hz[/tex].
Finally, the speed of the sound wave (v) can be calculated using the equation v = λf. Plugging in the values we get,
[tex]v \approx 0.123 m \times 2770.4 Hz \approx 340.1 m/s[/tex].
Learn more about wavelength here:
https://brainly.com/question/30532991
#SPJ11
A speedometer is placed upon a tree falling object in order to measure its instantaneous speed during the course of its fall its speed reading (neglecting air resistance) would increase each second by
The acceleration due to gravity is given as 9.8 meters per second per second (m/s²) since we can ignore air resistance. Thus, the speedometer will measure a constant increase in speed during the fall. During each second of the fall, the speed reading will increase by 9.8 meters per second (m/s). Therefore, the speedometer would measure a constant increase in speed during the fall by 9.8 m/s every second.
If a speedometer is placed upon a tree falling object in order to measure its instantaneous speed during the course of its fall, its speed reading (neglecting air resistance) would increase each second by 10 meters per second. This is because the acceleration due to gravity on Earth is 9.8 meters per second squared, which means that an object's speed increases by 9.8 meters per second every second it is in free fall.
For example, if an object is dropped from a height of 10 meters, it will hit the ground after 2.5 seconds. In the first second, its speed will increase from 0 meters per second to 9.8 meters per second. In the second second, its speed will increase from 9.8 meters per second to 19.6 meters per second. And so on.
It is important to note that air resistance will slow down an object's fall, so the actual speed of an object falling from a given height will be slightly less than the theoretical speed calculated above. However, the air resistance is typically very small for objects that are falling from relatively short heights, so the theoretical calculation is a good approximation of the actual speed.
To learn more about speed visit: https://brainly.com/question/13943409
#SPJ11
The electronic density of a metal is 4.2*1024 atoms/m3 and has a refraction index n = 1.53 + i2.3.
a)find the plasma frequency. The charge of electrons is qe = 1.6*10-19C and the mass of these e- is me=9.1*10-31kg , єo = 8.85*10-12 c2/Nm2.
b) please elaborate in detail if this imaginary metal is transparent or not
c) calculate the skin depth for a frequency ω = 2*1013 rad/s
a) The plasma frequency is approximately [tex]1.7810^{16}[/tex] rad/s.
b) The imaginary metal is not transparent.
c) The skin depth is approximately [tex]6.3410^{-8}[/tex] m.
The plasma frequency is calculated using the given electronic density, charge of electrons, electron mass, and vacuum permittivity. The plasma frequency (ωp) can be calculated using the formula ωp = √([tex]Ne^{2}[/tex] / (me * ε0)). Plugging in the given values, we have Ne = [tex]4.210^{24}[/tex] atoms/[tex]m^{3}[/tex], e = [tex]1.610^{19}[/tex] C, me = [tex]9.110^{-31}[/tex] kg, and ε0 = 8.8510-12 [tex]C^{2}[/tex]/[tex]Nm^{2}[/tex]. Evaluating the expression, the plasma frequency is approximately 1.78*[tex]10^{16}[/tex] rad/s.
The presence of a non-zero imaginary part in the refractive index indicates that the metal is not transparent. To determine if the imaginary metal is transparent or not, we consider the imaginary part of the refractive index (2.3). Since the absorption coefficient is non-zero, the metal is not transparent.
The skin depth is determined by considering the angular frequency, conductivity, and permeability of free space. The skin depth (δ) can be calculated using the formula δ = √(2 / (ωμσ)), where ω is the angular frequency, μ is the permeability of free space, and σ is the conductivity of the metal.
To learn more about frequency click here:
brainly.com/question/254161
#SPJ11
Find the magnitude of the electric field where the vertical
distance measured from the filament length is 34 cm when there is a
long straight filament with a charge of -62 μC/m per unit
length.
E=___
The magnitude of the electric field where the vertical distance measured from the filament length is 34 cm when there is a long straight filament with a charge of -62 μC/m per unit length is 2.22x10^5 N/C. Therefore, E= 2.22 x 10^5 N/C. A charged particle placed in an electric field experiences an electric force.
The magnitude of the electric field where the vertical distance measured from the filament length is 34 cm when there is a long straight filament with a charge of -62 μC/m per unit length is 2.22x10^5 N/C. Therefore, E= 2.22 x 10^5 N/C. A charged particle placed in an electric field experiences an electric force. The magnitude of the electric field is defined as the force per unit charge that acts on a positive test charge placed in that field. The electric field is represented by E.
The electric field is a vector quantity, and the direction of the electric field is the direction of the electric force acting on the test charge. The electric field is a function of distance from the charged object and the amount of charge present on the object. The electric field can be represented using field lines. The electric field lines start from the positive charge and end at the negative charge. The electric field due to a long straight filament with a charge of -62 μC/m per unit length is given by, E = (kλ)/r
where, k is Coulomb's constant = 9 x 109 N m2/C2λ is the charge per unit length
r is the distance from the filament
E = (9 x 109 N m2/C2) (-62 x 10-6 C/m) / 0.34 m = 2.22 x 105 N/C
To know more about electric field visit:
https://brainly.com/question/30544719
#SPJ11
An ideal gas expands isothermally, performing 5.00×10 3
J of work in the process. Calculate the change in internal energy of the gas. Express your answer with the appropriate units. Calculate the heat absorbed during this expansion. Express your answer with the appropriate units.
For an isothermal expansion of an ideal gas, the change in internal energy is zero. In this case, the gas performs 5.00×10^3 J of work, and the heat absorbed during the expansion is also 5.00×10^3 J.
An isothermal process involves a change in a system while maintaining a constant temperature. In this case, an ideal gas is expanding isothermally and performing work. We need to calculate the change in internal energy of the gas and the heat absorbed during the expansion.
To calculate the change in internal energy (ΔU) of the gas, we can use the first law of thermodynamics, which states that the change in internal energy is equal to the heat (Q) absorbed or released by the system minus the work (W) done on or by the system. Mathematically, it can be represented as:
ΔU = Q - W
Since the process is isothermal, the temperature remains constant, and the change in internal energy is zero. Therefore, we can rewrite the equation as:
0 = Q - W
Given that the work done by the gas is 5.00×10^3 J, we can substitute this value into the equation:
0 = Q - 5.00×10^3 J
Solving for Q, we find that the heat absorbed during this expansion is 5.00×10^3 J.
To know more about the first law of thermodynamics, refer here:
https://brainly.com/question/32101564#
#SPJ11
A dry cell having internal resistance r = 0.5 Q has an electromotive force & = 6 V. What is the power (in W) dissipated through the internal resistance of the cell, if it is connected to an external resistance of 1.5 Q?
I. 4.5 II. 5.5 III.3.5 IV. 2.5 V. 6.5
The power (in W) dissipated through the internal resistance of the cell, if it is connected to an external resistance of 1.5 Q is 4.5 W. Hence, the correct option is I. 4.5.
The expression for the power (in W) dissipated through the internal resistance of the cell, if it is connected to an external resistance of 1.5 Q is as follows:
Given :The internal resistance of a dry cell is `r = 0.5Ω`.
The electromotive force of a dry cell is `ε = 6 V`.The external resistance is `R = 1.5Ω`.Power is given by the expression P = I²R. We can use Ohm's law to find current I flowing through the circuit.I = ε / (r + R) Substituting the values of ε, r and R in the above equation, we getI = 6 / (0.5 + 1.5)I = 6 / 2I = 3 A Therefore, the power dissipated through the internal resistance isP = I²r = 3² × 0.5P = 4.5 W Therefore, the power (in W) dissipated through the internal resistance of the cell, if it is connected to an external resistance of 1.5 Q is 4.5 W. Hence, the correct option is I. 4.5.
To know more about internal resistance visit
https://brainly.com/question/23575577
#SPJ11
In a RC circuit, C=4.15microC and the emf of the battery is E=59V. R is unknown and the time constant is Tau(s). Capacitor is uncharged at t=0s. What is the capacitor charge at t=2T. Answer in C in the hundredth place.
The capacitor charge at t = 2T is approximately 1.49 microC. In an RC circuit, the charge on a capacitor can be calculated using the equation Q = Q_max * (1 - e^(-t/Tau)), Q_max is maximum charge the capacitor can hold, and Tau is time constant.
Given that the capacitor is uncharged at t = 0s, we can assume Q_max is equal to the total charge Q_max = C * E, where C is the capacitance and E is the emf of the battery.
Substituting the given values, C = 4.15 microC and E = 59V, we can calculate Q_max:
Q_max = (4.15 microC) * (59V) = 244.85 microC
Since we want to find the capacitor charge at t = 2T, we substitute t = 2T into the equation:
Q = Q_max * (1 - e^(-2))
Using the exponential function, we find:
Q = 244.85 microC * (1 - e^(-2))
≈ 244.85 microC * (1 - 0.1353)
≈ 244.85 microC * 0.8647
≈ 211.93 microC
Converting to the hundredth place, the capacitor charge at t = 2T is approximately 1.49 microC.
Therefore, the capacitor charge at t = 2T is approximately 1.49 microC.
To learn more about capacitor , click here : https://brainly.com/question/29100869
#SPJ11
A rod made of insulating material has a length L=7.3 cm, and it carries a chatge of Q=−230 n C that is not distributed uniormly in the fod. Twice as much charge is on one side of the rod as is on the other. Calculate the strength of the rod's electric field at a point 4 m away from the rod's center along an axis perpendicular to the rod. 32 V/m 108Vim 70 Vim 121 Vim 54Vim 130 Vim 100 Vim B. V/M
The strength of the electric field at a point 4 m away from the center of the rod, along an axis perpendicular to the rod, is 54 V/m.
To calculate the electric field strength, we can divide the rod into two segments and treat each segment as a point charge. Let's assume the charge on one side of the rod is q, so the charge on the other side is 2q. We are given that the total charge on the rod is Q = -230 nC.
Since the charges are not uniformly distributed, we need to find the position of the center of charge (x_c) along the length of the rod. The center of charge is given by:
x_c = (Lq + (L/2)(2q)) / (q + 2q)
Simplifying the expression, we get:
x_c = (7.3q + 3.652q) / (3q)
x_c = (7.3 + 7.3) / 3
x_c = 4.87 cm
Now we can calculate the electric field strength at the point 4 m away from the center of the rod. Since the rod is made of an insulating material, the electric field outside the rod can be calculated using Coulomb's law:
E = k * (q / r^2)
where k is the electrostatic constant (k = 9 x 10^9 Nm^2/C^2), q is the charge, and r is the distance from the center of charge to the point where we want to calculate the electric field.
Converting the distance to meters:
r = 4 m
Plugging in the values into the formula:
E = (9 x 10^9 Nm^2/C^2) * (2q) / (4^2)
E = (9 x 10^9 Nm^2/C^2) * (2q) / 16
E = (9 x 10^9 Nm^2/C^2) * (2q) / 16
E = 0.1125 * (2q) N/C
Since the total charge on the rod is Q = -230 nC, we have:
-230 nC = q + 2q
-230 nC = 3q
Solving for q:
q = -230 nC / 3
q = -76.67 nC
Plugging this value back into the electric field equation:
E = 0.1125 * (2 * (-76.67 nC)) N/C
E = -0.1125 * 153.34 nC / C
E = -17.23 N/C
The electric field is a vector quantity, so its magnitude is always positive. Taking the absolute value:
|E| = 17.23 N/C
Converting this value to volts per meter (V/m):
1 V/m = 1 N/C
|E| = 17.23 V/m
Therefore, the strength of the rod's electric field at a point 4 m away from the rod's center along an axis perpendicular to the rod is approximately 17.23 V/m.
To learn more about electric field click here:
brainly.com/question/30544719
#SPJ11
An Australian emu is running due north in a straight line at a speed of 13.0 m/s and slows down to a speed of 10.6 m/s in 3.40 s. (a) What is the magnitude and direction of the bird's acceleration? (b) Assuming that the acceleration remains the same, what is the bird's velocity after an additional 2.70 s has elapsed?
The magnitude of acceleration is given by the absolute value of Acceleration.
Given:
Initial Velocity,
u = 13.0 m/s
Final Velocity,
v = 10.6 m/s
Time Taken,
t = 3.40s
Acceleration of the bird is given as:
Acceleration,
a = (v - u)/t
Taking values from above,
a = (10.6 - 13)/3.40s = -0.794 m/s² (acceleration is in the opposite direction of velocity as the bird slows down)
:|a| = |-0.794| = 0.794 m/s²
The direction of the bird's acceleration is in the opposite direction of velocity,
South.
To calculate the velocity after an additional 2.70 s has elapsed,
we use the formula:
Final Velocity,
v = u + at Taking values from the problem,
u = 13.0 m/s
a = -0.794 m/s² (same as part a)
v = ?
t = 2.70 s
Substituting these values in the above formula,
v = 13.0 - 0.794 × 2.70s = 10.832 m/s
The final velocity of the bird after 2.70s has elapsed is 10.832 m/s.
The direction is still North.
To know more about Acceleration visit:
https://brainly.com/question/19537384
#SPJ11
6 A speedometer estimates linear speed based on angular speed of tires. If you switch to speed. larger tires, then the speedometer will read a lower linear speed than the true linear 7. Two spheres have the same mass and radius but one is hollow. If you roll both of them from the same height, the hollow one reaches to the ground later. 8. Two disks spin with the same angular momentum, but disk 1 has more Kinetic Energy than disk 2. Disk two has a larger moment of inertia. 9. You hold a spinning bicycle wheel while standing on a turntable. If you flip the wheel over, the turntable will move in the same direction. 10. If you used 5000 joules to throw a ball, it would travel faster if you threw in such a way that it is rotating
6. When switching to larger tires, the speedometer will display a lower linear speed than the true linear speed. This is because larger tires have a greater circumference, resulting in each revolution covering a longer distance compared to the original tire size.
The speedometer is calibrated based on the original tire size and assumes a certain distance per revolution. As a result, with larger tires, the speedometer underestimates the actual linear speed.
7. Two spheres with the same mass and radius are rolled from the same height. The hollow sphere reaches the ground later than the solid sphere. This is due to the hollow sphere having less mass and, consequently, less inertia. It requires less force to accelerate the hollow sphere compared to the solid sphere. As a result, the hollow sphere accelerates slower and takes more time to reach the ground.
8. Two disks with the same angular momentum are compared, but disk 1 has more kinetic energy than disk 2. Disk 2 has a larger moment of inertia, which is a measure of the resistance to rotational motion. The disk with greater kinetic energy has a higher velocity than the disk with lower kinetic energy. While both disks possess the same angular momentum, their different moments of inertia contribute to the difference in kinetic energy.
9. When a spinning bicycle wheel is flipped over while standing on a turntable, the turntable moves in the same direction. This phenomenon is explained by the conservation of angular momentum. Flipping the wheel changes its angular momentum, and to conserve angular momentum, the turntable moves in the opposite direction to compensate for the change.
10. If a ball is thrown with 5000 joules of energy and it is rotating, it will travel faster. The conservation of angular momentum states that when the net external torque acting on a system is zero, angular momentum is conserved. As the ball is thrown with spin, it possesses angular momentum that remains constant. The rotation of the ball does not affect its forward velocity, which is determined by the initial kinetic energy. However, the rotation influences the trajectory of the ball.
To learn more about speedometer, you can visit the following link:
brainly.com/question/32573142
#SPJ11
Comparing the radiation power loss for electron ( Pe )
with radiation power loss for the proton ( Pp ) in the synchrotron,
one gets :
1- Pe = Pp = 0
2- Pe << Pp
3- Pe >> Pp
4- Pe ≈ Pp
When comparing the radiation power loss for electrons (Pe) and protons (Pp) in a synchrotron, the correct answer is 2- Pe << Pp. This means that the radiation power loss for electrons is much smaller than that for protons.
The radiation power loss in a synchrotron occurs due to the acceleration of charged particles. It depends on the mass and charge of the particles involved.
Electrons have a much smaller mass compared to protons but carry the same charge. Since the radiation power loss is proportional to the square of the charge and inversely proportional to the square of the mass, the power loss for electrons is significantly smaller than that for protons.
Therefore, option 2- Pe << Pp is the correct choice, indicating that the radiation power loss for electrons is much smaller compared to that for protons in a synchrotron.
Learn more about synchrotron here:
brainly.com/question/31070723
#SPJ11
How much input force is required to extract an output force of 500 N from a simple machine that has a mechanical advantage of 8?
An input force of 62.5 N is required to extract an output force of 500 N from a simple machine that has a mechanical advantage of 8.
The mechanical advantage of a simple machine is defined as the ratio of the output force to the input force. Therefore, to find the input force required to extract an output force of 500 N from a simple machine with a mechanical advantage of 8, we can use the formula:
Mechanical Advantage (MA) = Output Force (OF) / Input Force (IF)
Rearranging the formula to solve for the input force, we get:
Input Force (IF) = Output Force (OF) / Mechanical Advantage (MA)
Substituting the given values, we have:
IF = 500 N / 8IF = 62.5 N
Therefore, an input force of 62.5 N is required to extract an output force of 500 N from a simple machine that has a mechanical advantage of 8. This means that the machine amplifies the input force by a factor of 8 to produce the output force.
This concept of mechanical advantage is important in understanding how simple machines work and how they can be used to make work easier.
To know more about input force, visit:
https://brainly.com/question/28919004
#SPJ11
To extract an output force of 500 N from a simple machine that has a mechanical advantage of 8, the input force required is 62.5 N.
Mechanical advantage is defined as the ratio of output force to input force.
The formula for mechanical advantage is:
Mechanical Advantage (MA) = Output Force (OF) / Input Force (IF)
In order to determine the input force required, we can rearrange the formula as follows:
Input Force (IF) = Output Force (OF) / Mechanical Advantage (MA)
Now let's plug in the given values:
Output Force (OF) = 500 N
Mechanical Advantage (MA) = 8
Input Force (IF) = 500 N / 8IF = 62.5 N
Therefore, extract an output force of 500 N from a simple machine that has a mechanical advantage of 8, the input force required is 62.5 N.
To know more about force, visit:
https://brainly.com/question/30526425
#SPJ11
An LC circuit consists of a 2.5 mH inductor and a 4.5 μF
capacitor. its impedance Z at 55 Hz in Ω.Find its impedance
Z at 5 kHz in Ω.
The impedance of the LC circuit at 55 Hz is approximately 269.68 Ω and at 5 kHz is approximately 4.43 Ω.
To find the impedance (Z) of the LC circuit at 55 Hz and 5 kHz, we can use the formula for the impedance of an LC circuit:
Z = √((R^2 + (ωL - 1/(ωC))^2))
Given:
L = 2.5 mH = 2.5 × 10^(-3) H
C = 4.5 μF = 4.5 × 10^(-6) F
1. For 55 Hz:
ω = 2πf = 2π × 55 = 110π rad/s
Z = √((0 + (110π × 2.5 × 10^(-3) - 1/(110π × 4.5 × 10^(-6)))^2))
≈ √((110π × 2.5 × 10^(-3))^2 + (1/(110π × 4.5 × 10^(-6)))^2)
≈ √(0.3025 + 72708.49)
≈ √72708.79
≈ 269.68 Ω (approximately)
2. For 5 kHz:
ω = 2πf = 2π × 5000 = 10000π rad/s
Z = √((0 + (10000π × 2.5 × 10^(-3) - 1/(10000π × 4.5 × 10^(-6)))^2))
≈ √((10000π × 2.5 × 10^(-3))^2 + (1/(10000π × 4.5 × 10^(-6)))^2)
≈ √(19.635 + 0.00001234568)
≈ √19.63501234568
≈ 4.43 Ω (approximately)
Therefore, the impedance of the LC circuit at 55 Hz is approximately 269.68 Ω and at 5 kHz is approximately 4.43 Ω.
Learn more about impedance: https://brainly.com/question/17153017
#SPJ11