766.7856 g
Molecular weight of Aluminium Nitrate is 212.996 g/mol. 3.6 moles of Aluminium Nitrate is: 212.996 × 3.6 = 766.7856
What are resistors? please help
Answer:Resistor Basics
Resistors are electronic components which have a specific, never-changing electrical resistance. The resistor's resistance limits the flow of electrons through a circuit.
They are passive components, meaning they only consume power (and can't generate it). Resistors are usually added to circuits where they complement active components like op-amps, microcontrollers, and other integrated circuits. Commonly resistors are used to limit current, divide voltages, and pull-up I/O lines.
Resistor units
The electrical resistance of a resistor is measured in ohms. The symbol for an ohm is the greek capital-omega: Ω. The (somewhat roundabout) definition of 1Ω is the resistance between two points where 1 volt (1V) of applied potential energy will push 1 ampere (1A) of current.
As SI units go, larger or smaller values of ohms can be matched with a prefix like kilo-, mega-, or giga-, to make large values easier to read. It's very common to see resistors in the kilohm (kΩ) and megaohm (MΩ) range (much less common to see miliohm (mΩ) resistors). For example, a 4,700Ω resistor is equivalent to a 4.7kΩ resistor, and a 5,600,000Ω resistor can be written as 5,600kΩ or (more commonly as) 5.6MΩ.
Schematic symbol
All resistors have two terminals, one connection on each end of the resistor. When modeled on a schematic, a resistor will show up as one of these two symbols:
Resistor schematic symbols
Two common resistor schematic symbols. R1 is an American-style 1kΩ resistor, and R2 is an international-style 47kΩ resistor.
The terminals of the resistor are each of the lines extending from the squiggle (or rectangle). Those are what connect to the rest of the circuit.
The resistor circuit symbols are usually enhanced with both a resistance value and a name. The value, displayed in ohms, is obviously critical for both evaluating and actually constructing the circuit. The name of the resistor is usually an R preceding a number. Each resistor in a circuit should have a unique name/number. For example, here's a few resistors in action on a 555 timer circuit:
Answer: resistor is
Explanation:
A resistor controls the flow of the electrical current within a circuit. Resistors are made from materials like copper or carbon, which make it difficult for the electrical charges to flow through a circuit. The most common type of resistor is a carbon resistor, which is a general purpose resistor, best suited for lower-powered circuits.
Select odd one out.
I) O
II) Na
III) Cu
IV) Ag
Explanation:
0 is the odd one...............
and rest are metals and they lose electron and 0 gain electron and is non metal
3. You believe that water boils at 212 degrees Fahrenheit (100 degrees Celsius). Write the numberon the scale from best to worst.
1. Your cousin said that he tested the temperature of water boiling and found that it was 100°C.
2. Most people you know believe that water boils at 100°C.
3. You used a thermometer to measure the temperature at which water boiled. You repeated the experiment 3 times. Each time the thermometer read 100°C.
4. You read an article in a science journal from 50 different labs around the world that have tested the temperature of water and found that it boils at 100°C in every location.
You come across an article in a scientific journal from 50 different laboratories around the globe that measured the boiling point of water and discovered that it is 100°C everywhere.
What transpires when water is heated to 100 C (This is 212 F)?Water turns into gas around 212°F (100°C), which is the temperature at which it begins to boil (water vapor). Pressure affects the melting/freezing and boiling points. Water's boiling point changes when air pressure changes. The boiling point decreases with increasing altitude or decreasing pressure.
At 212 degrees Fahrenheit, does water boil, or at 100 degrees?Water has a freezing point of 32 degrees Fahrenheit and a boiling point of 212 degrees Fahrenheit on the Fahrenheit scale.
To know more about laboratories visit:-
https://brainly.com/question/28233400
#SPJ4
what is the formula of the compounds in B
pls help
Answer:
PCl3
Explanation:
The molecular formular of a compound shows the exact number of atoms of elements present in the compound. In this illustration, there is one atom of P and 3 atoms of Cl.
The formular is given as; PCl3
Answer:
PCl³
Explanation:
because there are 1 phosphorus atom and 2 chlorine atom.
In a water molecule, what type of bond forms between the oxygen and hydrogen atoms
An organism from the past that is related to all the organisms in the group is called?
Answer:
phylogenic trees/phylogeny
Explanation:
the evolutionary history and relationship of an organism or group of organisms is called its phylogeny
Pls help fast, I will give brainliest!
Answer:
c
Explanation:
The job of the ______ is to hold all of the parts of a cell together
Answer:
cell membrane
Explanation:
it holds everything together
Which sets of elements have similar chemical and physical properties?
1. Mg and Ra 2. Al and P 3. Be and Ba 4. Na and Cl
1 & 2 ,
2 & 3
1 & 3
2 & 4
Answer:
1 & 3
Explanation:
Elements have similar chemical and physical properties if and only if they belong to the same group of elements in the periodic table.
A group of elements in the periodic table is a family of elements, the elements in the in the same group have the same number of valence electrons in their outermost shell, share similar chemical reactivity (with slight variation within the group) and similar physical properties (with slight variation within the group).
Magnesium, radium, beryllium and barium all belong to group 2 hence they have similar chemical and physical properties.
28g of aluminum reacts with 45g oxygen
1) complete balanced equation?
2) what is the limiting reactant?
3) how many grams of product could be formed?
4) how many grams of excess would you predict?
5) if you actually measured 50g of product, what is the percent yield?
Answer:
answer below:
Explanation:
1) 4 Al + 3 O2 --> 2Al2O3.
2) Al mol= 28/27 = 1.037mol
O mol= 45/16 = 2.812mol
Al : O
4 : 2
x : 2.812
cross multiply
4 x 2.812/2 = 5.624 mol of Al
Al is limiting reactant
3) 28/5.246 = 5.34product can be formed (not that much sure)
4) 45/ 0.5185 = 86.79
86.79 - 5.34 = 81.45g
5) 50 / 81.45 x 100 = 61.39% ( i guess)
i hope this hleps you
what is gold on the periodic table of element
Answer:
Gold is element 79 and its symbol is Au.
How many moles are in 3.0g of A1203?
Answer:
0.065 moles
Explanation:
whoever can help me will get the brainliest! Please
Answer:
Food chain, in ecology, the sequence of transfers of matter and energy in the form of food from organism to organism. Food chains intertwine locally into a food web because most organisms consume more than one type of animal or plant. ... In a predator chain, a plant-eating animal is eaten by a flesh-eating animal.
Explanation:
Explain why it is necessary to use a mixture, alumina and cryolite, rather than just
alumina
Explanation:
The mixture of cryolite and aluminium oxide has a lower melting point than pure aluminium oxide. This means a lower amount of energy is required to establish effective conditions for electrolysis and thus makes it more cost effective.
Gas in a balloon occupies 3.3 liters. What volume will it occupy if the pressure is changed from 100 kPa to 90.0 kPa, if the temperature is held constant?
Answer:
3.7 L
Explanation:
Initial volume (V₁) = 3.3 L
Initial pressure (P₁) = 100 KPa
Final pressure (P₂) = 90 KPa
Final volume (V₂) =?
The final volume of the gas can be obtained by using the Boyle's law equation as follow:
P₁V₁ = P₂V₂
100 × 3.3 = 90 × V₂
330 = 90 × V₂
Divide both side by 90
V₂ = 330 / 90
V₂ = 3.7 L
Thus, the final volume of the gas is 3.7 L
why are metals poor choices for coffee mugs?
Answer:
They will stay too hot.
Explanation:
You would burn yourself on the mug and your drink would be too hot to drink.
What is the difference between a pure solvent and a solution? Do they have the same physical properties?
Answer:
The physical properties of a solution are different from those of the pure solvent. ... Colligative properties are those physical properties of solutions of nonvolatile solutes that depend only on the number of particles present in a given amount of solution, not on the nature of those particles.
Learn more:
brainly.com/question/12225553
Which of following is true of liquids?
Group of answer choices
The particles move at a high rate of speed
The particles have a medium amount of kinetic energy and slide past one another.
The particles vibrate in place.
The particles have a fixed volume and shape
Answer:
The particles have a medium amount of kinetic energy and slide past one another
Explanation:
If particles move at a high rate of speed its gas, and if they vibrate in place and they have a fixed volume and shape its probably a solid. So a medium amount of kinetic enery is correct.
When the equation H2 + Fe3O4 = Fe + H2O is completely balanced using the smallest whole numbers, the coefficient oH2 would be A.) 1 B.)2 C.) 3 D.) 4
Answer:
H2 would have a coefficient of 2.
Explanation:
According to the balanced chemical equation, the coefficient of hydrogen is 4.
What is chemical equation?Chemical equation is a symbolic representation of a chemical reaction which is written in the form of symbols and chemical formulas.The reactants are present on the left hand side while the products are present on the right hand side.
A plus sign is present between reactants and products if they are more than one in any case and an arrow is present pointing towards the product side which indicates the direction of the reaction .There are coefficients present next to the chemical symbols and formulas .
The first chemical equation was put forth by Jean Beguin in 1615.By making use of chemical equations the direction of reaction ,state of reactants and products can be stated. In the chemical equations even the temperature to be maintained and catalyst can be mentioned.
Learn more about chemical equation,here:
https://brainly.com/question/28294176
#SPJ5
Suppose a fox population exists in an ecosystem. Some of the foxes maintain a heavy coat year-round, while others shed their heavy coat in the summer. Summers in this ecosystem
are becoming steadily hotter because of global warming. Which members of the species will most likely be able to adapt to the changing temperatures?
subject science
Answer:
The fox who shed their heavy coat in the summer.
Explanation:
If a fox has the ability to shed its coat in the summer, it will have no difficulties adapting to new temperatures even during winter. However, the heavy-coated one will.
Which of the following is a product in the reaction described by the word equation below?
iron + copper(II) sulfate ----------> iron(II) sulfate +copper
Answer:
Please answer my question
what is the molecular shape of N2O2?
Answer:
If you're just looking at the Lewis Structure from the perspective of the octet rule, it does appear that the structure is correct. Dinitrogen always has a lone pair of electrons which could conceivably be used for dative bonding as you suggest. So from that perspective there appears to be nothing wrong at all - other than that it doesn't exist in nature in this way.
Explanation:
At which position on the diagram would an apple have the greatest potential energy?
Answer:
Position 1 because it is the highest from the ground.
Hope this helps!
UGRENT! Please help showing all work
Answer:
a. Oxygen
b. 20.39g of Al₂O₃
c. 87%
Explanation:
In order to produce 2moles of Al₂O₃, we need to make react 4 moles of Al, to 3 moles of O₂.
We determine the limiting reactant with the moles of each:
12.98g / 26.98g/mol = 0.481 moles of Al
9.6g / 32g/mol = 0.300 moles of oxygen
4 moles of Al react to 3 moles of O₂
Then, 0.481 mol may react to (0.481 . 3)/4 = 0.361 moles
We only have 0.300 moles of O₂ and we need 0.361. Oxygen is the limiting reactant.
So 3 moles of O₂ can produce 2 moles of Al₂O₃
Our 0.300 moles may produce (0.300 . 2) / 3 = 0.200 mol
Our theoretical yield is: 0.2 mol . 101.96g/ mol = 20.39 g
To determine the percent yield we calculate:
(Produced yield/ Thoeretical yield) . 100 → (17.74 /20.39) . 100 = 87%
1
What is the mass of 0.328 mol of CO2?
Answer:
use this conversation units to help you hope it helpsPlease help ASAP!! I’m stuck!!
Which statement is true based on the formula?
6CO2 + 6H2O —> C6H12O6
+ 6O2
1. The mass of carbon dioxide plus water is equal to the mass of sugar plus oxygen
2. The mass of carbon dioxide plus water is less than the mass of sugar plus oxygen
3. The mass of carbon dioxide plus water is greater than the mass of sugar plus oxygen
Answer:
The answer of this question is 3
how does pentene become pentane?
How does propene become propane?
Oday, you will observe drops of liquid water and compare them to drops of liquid isopropanol, noting whether either liquid evaporates. Given that the energy transferred in from the air will be the same for both liquids, make a prediction about whether both drops or only one drop will evaporate within five minutes. Explain your prediction below.
Answer:
Liquid isopropanol.
Explanation:
Liquid isopropanol will evaporate earlier than water because the boiling point of isopropanol is less than water. That liquid which have high boiling point require more heat energy for change into vapor state as compared to those liquids that has low boiling point. The isopropanol has boiling point i.e. 82.5 °C while on the other hand, water has boiling point i.e. 100 °C so we can say that isopropanol will evaporate first.
The liquid that will be the first to evaporate within 5 minutes is; Liquid Isopropanol
We have the 2 liquids as;
Liquid Isopropanol
Liquid water
Now, since we are dealing with the one that will evaporate within five minutes, we need to know their boiling points.
From online research;
Boiling point of liquid isopropanol is 82.5°C
Boiling point of liquid water is 100°C
Now, we are told that the same energy is transferred for both liquids. However, boiling point of the liquid with the lower boiling point will be achieved first and as a result will evaporate first since the next stage after boiling point is evaporation of steam.
Read more at;https://brainly.com/question/25324798
The sound of a trumpet ECHOES off a nearby mountain. This is which type of wave interaction?
Answer:
reflection
Explanation:
wave reflection is when a sound bounces off something it cannot go through, like echoing
Which of the following describes wind direction?
Wind direction is reported by the direction from which it originates. For example, a north or northerly wind blows from the north to the south. Wind direction is usually reported in cardinal (or compass) direction, or in degrees.