Answer:
Explanation:
What are the benefits of 3D design and 3D printing software?
The height of the mountain is 1002.048 m.
What is pressure?The perpendicular force per unit area, or the stress at a point within a confined fluid, is referred to as pressure in the physical sciences.
Atmospheric pressure is the force of the atmosphere pressing down on each square meter of Earth's surface. Pascals are used to express pressure in SI units; one pascal is equivalent to one newton per square meter.
Given parameters:
at the base of a mountain, the reading of a mercury barometer is = 75.58cm = 0.7558 m.
at the summit of a mountain, the reading of a mercury barometer is = 66.37cm = 0.6637 m.
Let the height of the mountain = h.
Then,
h × density of air × g = ( 0.7558 - 0.6637) m × density of mercury × g
⇒ h × 1.25kg/m³ = 0.0921 m × 13600kg/m³
⇒ h = 1002.048 m.
Hence, the height of the mountain is 1002.048 m.
Learn more about pressure here:
https://brainly.com/question/12971272
#SPJ2
A 200kg car is driving at 20m/s down the road when he sees a red light. He slows to a stop.
The car's initial momentum is ___kg m/s
The car's final momentum is ___kg m/s
The car's impulse is
___kg m/s
Answer:
Initial Momentum - 4000 kg*m/s
Final Momentum - 0 kg*m/s
Impulse: -4000 kg*m/s
Explanation:
The equation for momentum is P = mv
Initial Momentum
200kg * 20m/s = 4000 kg*m/s
Final Momentum
200kg * 0m/s = 0kg*m/s
Impulse = ΔP
Pfinal - Pintial = Impulse
0-4000 = -4000 kg*m/s
Photons with the highest frequency have the lowest _____.
A. wavelength
B. speed
C. color
D. energy
Answer:
a wavelength
Explanation:
A house is advertised as having 1460 square feet under roof. What is the area of this house in square meters?
Answer: 131.92 m
Explanation: The problem give above is a conversion problem. To convert any measurement from one unit to another, we need a relation for the original units to that of the desired unit. This relation is called the conversion factor. It is used by multiplying or dividing the factor depending on what is the unit of the original measurement. For this case, we need to convert from ft^2 to m^2. The conversion factor would be 1 foot is equal to 0.3048 m. So, we would be getting the square of the factor and then multiply to the original value.
1420 ft^2 ( 0.3048 m / 1 ft)^2 = 131.92 m
1The specific heat of substance (X) is greater than that for substance (Y). If equal amounts of heat are added to both these substances, the one reaching the higher temperature(assuming no phase change occurs for either) will be:
1. substance X
2. substance Y
3.there will be no difference in the final temperature.
4.both X and Y
Answer:
Substance Y
Explanation:
A substance with a high specific heat capacity can absorb a large quantity of heat before it will raise in temperature. A substance with a low specific heat requires relatively little heat to raise its temperature. Thus, if the same amount of energy was added to both substances, substance Y will reach the higher temperature, while substance X would require more energy to reach high temperatures.
Answer:
2. substance Y
Explanation:
specific heat is how much heat is needed to warm up something. Y has smaller specific heat means it warm up more w/ same amount of heat.
4. In the display window of the toy store at the local mall, a battery-powered plane is suspended from a string and flying in a horizontal circle. The 631 gram plane makes a complete circle every 2.15 seconds. The radius of the circle is 0.950 m. Determine the velocity, angular velocity, acceleration, and net force acting upon the plane.
Answer:
The solution is given below
Explanation:
The computation is shown below:
Given that
Mass of plane, m is 631 g = 0.631 Kg
The Time period for one circle is 2.15 s
The Radius of circle = 0.95 m
Now the velocity of the plane, v = rω
where,
angular velocity, ω = (θ ÷ t)
For one complete circle, θ = 2π
and Time period T is provided = 2.15 s
Thus, ω = 2π ÷ T = 2π ÷ 2.15
So, velocity, v = rω
= r × ( 2π ÷ 2.15 )
= 0.95 × (2π ÷2.15)
= 2.776 m/s
The Acceleration of the plane, a = rω^2
= 0.95 × (2π ÷ 2.15)^2
= 8.114 m/s^2
The Net force acting upon the plane, F = Centripetal force i.e.
= mv2 ÷ r
F = mv2 / r
= (0.631 × 2.7762) ÷ 0.95
= 5.118 N
a spring has a spring constant of 330 n/m. how far is the spring compressed when 150 newtons of force are used?
a. 0.0014 meters
b. 0.45 meters
c. 2.2 meters
d. 5.0 meters
show your work.
Answer:
b. 0.45 meters
Explanation:
Given the following data;
Spring constant, k = 330 N/m
Force = 150 N
To find the extension of the spring;
Mathematically, the force exerted on a spring is given by the formula;
Force = spring constant * extension
Substituting into the formula, we have;
150 = 330 * extension
Extension, e = 150/330
Extension, e = 0.45 meters
How much stronger is the electric force between two
protons than the gravitational force between them?
Answer:
Explanation:
The electric force between two protons is 10^36 times stronger than the gravitational force between them.
Answer:
Electric force is 1.23 x 10³⁶ times stronger than gravitational force.
Explanation:
First, we will calculate the gravitational force using Newton's Law:
[tex]F_G = \frac{Gm^2}{r^2}\\\\[/tex]
where,
F_G = Gravitational Force = ?
G = Gravitational Constant = 6.67 x 10⁻¹¹ Nm²/kg²
m = mass of proton = 1.67 x 10⁻²⁷ kg
r = distance between protons
Therefore,
[tex]F_G = \frac{(6.67\ x\ 10^{-11}\ Nm^2/kg^2)(1.67\ x\ 10^{-27}\ kg)^2}{r^2}\\\\F_G = \frac{1.86\ x\ 10^{-64}\ Nm^2}{r^2}\\\\[/tex]
Now, we will calculate the electrostatic force using Colomb's Law:
[tex]F_E = \frac{kq^2}{r^2}\\\\[/tex]
where,
F_E = Electrostatic Force = ?
k = Colomb's Constant = 9 x 10⁹ Nm²/C²
q = charge of proton = 1.6 x 10⁻¹⁹ C
r = distance between protons
Therefore,
[tex]F_E = \frac{(9\ x\ 10^{9}\ Nm^2/kg^2)(1.6\ x\ 10^{-19}\ C)^2}{r^2}\\\\F_E = \frac{2.3\ x\ 10^{-28}\ Nm^2}{r^2}\\\\[/tex]
Dividing both forces:
[tex]\frac{F_E}{F_G} = \frac{2.3\ x\ 10^{-28}}{1.86\ x\ 10^{-64}}[/tex]
F_E = 1.23 x 10³⁶ F_G
Therefore, electric force is 1.23 x 10³⁶ times stronger than gravitational force.
After rolling halfway down an incline a marble's kinetic energy is
A. impossible to determine
B. the same as its potential energy
C. greater than its potential energy
D. less than its potential energy
12. 2007: The figure below show two identical trollbys with loads A and B. The
loads are identical in shape and size.
D
Given that the density of A is greater than that of B, explain why the
trolley in figure 3 (in) is more stable
Answer:
you need to provide a figure that came with the problem.
When a species has no members left that are alive
Answer:
it means that species is extinct.
Explanation:
have a good day :)
describe los ejercicios que caliente las extremidades superiores del cuerpo
Answer:
todas las cosas que la cuerda de salto hará
Explanation:
1. Mueva suavemente las muñecas y prepárese para levantar la parte superior del cuerpo.
2.Activa tus hombros sin presionarlos.
3. Calienta todo tu cuerpo elevando tu frecuencia cardíaca y cebando para la coordinación de todo el cuerpo que necesitas para el entrenamiento de la parte superior del cuerpo.
Who serves as the presiding officer of the Senate?
Who serves as the presiding officer of the Senate?
[tex]{ \bf{ \underbrace{Answer :}}}[/tex]
The [tex]\sf\purple{Vice\:President}[/tex] of the United States serves as the presiding officer of the Senate.
At present, [tex]\sf\red{Kamala\:Harris}[/tex] is the president of the Senate.
[tex]\bold{ \green{ \star{ \orange{Hope\:it\:helps.}}}}⋆[/tex]
In A. C. motor capacitor is used
p.Can dicouly [BPKIHS 2000
to reduce ripples b. to decrease A. C.
c. to increase A. C. d. to decrease D. C.
a.
34
Answer:
d. to decrease D. C.
Explanation:
d. to decrease D. C.
We know the mass and luminosity of the star. We also know the mass of the spacecraft and the area of its stellar sail. We must find the net force exerted on the spacecraft, as well as the direction of its acceleration. We are asked to find both the net force exerted on the spacecraft and the direction of the acceleration. Which principle is best used to find the direction of the acceleration once the net force has been found
Answer:
Newton's principle of force, the variation of the momentum and the acceleration have the same direction
Explanation:
To find the force exerted by the star on the sail of the ship, the expression of the momentum of the radiation is used, which in the case of a total reflection
p = [tex]\frac{2U}{c}[/tex]
where p is the momentum and U the incident energy and c the speed of light.
The strength I could get from
F = [tex]\frac{dp}{dt}[/tex]
the direction of the acceleration is the direction of the momentum, therefore the principle to find the acceleration of is Newton's principle of force, the variation of the momentum and the acceleration have the same direction.
54. Which of the following behaviors is most closely
associated with the foot-in-the-door phenomenon?
(A) Beth continues to participate in class because
she is positively reinforced.
(B) Adam is sleeping while the rest of his
classmates are working on their group
project
(C) Sutan asks his father for $5, and when he
agrees, Sutan asks him for $15 more.
(D) James feels pressure to go to the movies with
his friends even though he prefers to go
bowling.
(E) Diana feels guilty because she did not help
her family clear the table after dinner.
Answer:
C
Explanation:
Foot-in-the-door technique is a compliance tactic that aims at getting a person to agree to a large request by having them agree to a modest request first
The behavior that should be closely associated is option c. Sutan asks his father for $5, and when he agrees, Sutan asks him for $15 more.
What is the foot-in-the-door phenomenon?It is a tactic of compliance that focuses on agreeing on the person by having a request.
It shows the connection that lies between the person who is asking for a request and the person who is being asked.
So based on this, option c is correct.
learn more about behavior here: https://brainly.com/question/15661050
When oxygen in water interacts with iron it results in O A rust forming O B) a chemical change C) oxidation O D) all of the above
The chart shows the masses of selected particles.
Particle
Mass
2350
137 9 u
6
92
138
Ba
K:
on
94.9u
1.0 u
In the equation u + Ön – 133Ba + K+ + 36n+E , the energy E is equivalent to a mass of
1.
0.2 u
2.
2.0 u
3.
2.2 u
4.
0.0 u
Answer: 0.2 u
Explanation:
The atomic mass of nuclide is written as a superscript. On the left (reactants) aide of the nuclear equation shown, the total atomic mass is 235.0 + 1.0 u = 236 u. On the right (products) side reaction, the total atomic mass is 137.9u + 94.9u + 3 x 1.0u = 235.8 u. Therefore, 0.2 mass units must have been converted into energy.
Answer the following question according to formal grammatical rules.
Which of the following sentences corrects the pronoun errors in this sentence?
If a person wants to help their community, they should research opportunities.
A. If a person wants to help their community, you should research opportunities.
B. If you want to help your community, a person should research opportunities.
C. If people want to help their community, they should research opportunities.
D. If a person wants to help it, they should research opportunities.
If people want to help their community, they should research opportunities corrects the pronoun errors in this sentence.
What is a Pronoun?This is defined as a word which is used instead of a noun and examples include he, she etc.
In this scenario, the word 'people' agrees with the possessive adjective 'their' and the personal pronoun 'they', which is referred to the third-person plural hence the reason why option C is the most appropriate choice.
Read more about Pronoun here https://brainly.com/question/26257764
Answer:
D
Explanation:
D
The maximum allowable resistance for an underwater cable is one hundredth of an ohm per
meter and the resistivity of copper is 1.54 x 10-80m.
a) Calculate the smallest cross sectional area of copper cable that could be used.
Answer:
A = 1.54 x 10⁻⁵ m² = 15.4 mm²
Explanation:
The resistance of a wire can be given by the following formula:
[tex]R = \frac{\rho L}{A}\\\\A = \frac{\rho L}{R} = \frac{\rho}{\frac{R}{L} }[/tex]
where,
A = smallest cross-sectional area = ?
ρ = resistivity of copper = 1.54 x 10⁻⁸ Ωm
[tex]\frac{R}{L}[/tex] = resistance per unit length of wire = 0.001 Ω/m
Therefore,
[tex]A = \frac{1.54\ x\ 10^{-8}\ \Omega m}{0.001\ \Omega/m}[/tex]
A = 1.54 x 10⁻⁵ m² = 15.4 mm²
please help meeeee :((((((((((
Answer:
hello me
Explanation:
help me thisanswer
1 pts
Harry spent his summer playing guitar on the corner trying to earn some extra money. He would keep his guitar
case open for people to drop extra change into. Sometimes people would put money in the case and sometimes
people would be rude. Putting money in the hat is a to Harry's behavior.
Tir
Atte
1M
Negative reinforcement
Positive reinforcement
O Negative punishment
Positive punishment
Question 2
1 pts
O
SIC
acer
Answer:
Positive reinforcement
A car comes to a stop six seconds after the driver applies the brakes. While the brakes are on, the following velocities are recorded:
Time since brakes applied (sec) 0 2 4 6
Velocity (ft/s) 87 44 16 0
Give lower and upper estimates (using all of the available data) for the distance the car traveled after the brakes were applied.
Answer:
Explanation:
deceleration during first 2 s = (87 - 44) / 2 =21.5 m /s²
deceleration during next 2 s = (44 - 16) / 2 =14 m /s²
deceleration during last 2 s = (16 - 0) / 2 = 8 m /s²
If we assume the acceleration to be uniform during 3 readings
distance travelled during first 2 s
v² - u² = 2 a s
87² - 44² = 2 x 21.5 x s
s = 7569 - 1936 / 43
= 176 m
distance travelled during next 2 s
44² - 16² = 2 x 14 x s
s = 1936 - 256 / 28
= 60 m
distance travelled during last 2 s
16² - 0² = 2 x 8 x s
s = 256 / 16
= 16 m
Total distance travelled = 176 + 60 + 16 = 252 m
If we assume the acceleration as non- uniform , we first calculate average acceleration as follows .
average acceleration = (87 - 0)/ 6 = 14.5 m /s²
v² - u² = 2 a s
87² - 0² = 2 x 14.5 x s
s = 7569 / 29
= 261 m
Hence lower estimate of distance travelled = 252 m ; upper estimate of distance travelled = 261 m .
Two identical thermally insulated spherical tanks, A and B, are connected by a valve. Initially tank A contains 20mol of an ideal diatomic gas, tank B is evacuated, and the valve is closed.
If the valve is opened and the gas expands isothermally fromA to B, what is the change in the entropy of the gas?
Answer:
Explanation:
Volume of gas is doubled isothermally . Let the temperature of the gas be T .Work done by the gas
W = 2.303 nRT log 2 V / V
Since expansion is isothermal , Δ E = 0
Q = ΔE + W
Q = W
Q = 2.303 nRT log 2 V / V
Q / T = 2.303 n R log 2
Change in entropy = ΔS = Q / T = 2.303 n R log 2
= 2.303 x 20 x 8.3 x .3010 J T⁻¹.
= 115 J T⁻¹.
The required change in the entropy of the gas is 115 J/K.
Given data:
The number of moles of diatomic gas in tank A is, n = 20 mol.
The expansion takes place isothermally, which means the volume is doubled at the constant temperature. Therefore, work done during the isothermal expansion is,
W = 2.303 nRT log 2 V / V
Since expansion is isothermal , Δ E = 0. Then by using the first law of thermodynamics as,
Q = ΔE + W
Q = W
Q = 2.303 nRT log 2 V / V
Q / T = 2.303 n R log 2
Also, we that the expression for the change in Entropy is,
ΔS = Q / T = 2.303 n R log 2
Solving as,
ΔS = 2.303 x 20 x 8.3 x .3010
ΔS = 115 J/K
Thus, we can conclude that the required change in the entropy of the gas is 115 J/K.
Learn more about the entropy change here:
https://brainly.com/question/1301642
A truck contains both hydraulic brakes (reliability 0.96) and mechanical brakes (reliability 0.99). What is the probability of stopping the truck (i) while moving at a high speed, assuming both systems must work to avoid hitting a vehicle stalled in the roadway, and (ii) while moving at a low speed, assuming either system will stop the truck in time if they function properly
Answer:
i) 0.9504
ii) 0.0452
Explanation:
Given data: reliability of hydraulic brakes= 0.96
reliability of mechanical brakes = 0.99
So the probability of stopping the truck = 0.96×0.99= 0.9504
At low speed
case: A works and B does not
= 0.96×(1-0.99) = 0.0096
case2 : B works and A does not
= 0.99×(1-0.96) = 0.0396
Therefore, probality of stopping = 0.0096+0.0396 = 0.0492
An automobile traveling at a speed of 28.3 m/s applies its brakes and comes to a stop in 4.9 s. If the automobile has a mass of 1.1 x 103 kg, what is the average horizontal force exerted on it during braking? Assume the road is level.
Find Magnitude and direction
WILL GIVE BRAINLIEST
Answer:
i say it would be 32.5 m if the brakes comes and stops. the road is 3.7 x 105
Explanation:
Starting from rest, a car takes 2.4 s to travel the first 15 m. Assuming a constant acceleration, how long will it take the car to travel the next 15 m?
Answer:
The time it will take the car to travel the next 15 m is 1 s.
Explanation:
Given;
initial velocity of the car, u = 0
time of motion, t = 2.4 s
initial distance traveled, d = 15 m
determine the constant acceleration of the car;
d = ut + ¹/₂at²
15 = 0 + (0.5 x 2.4²)a
15 = 2.88a
a = 15 / 2.88
a = 5.21 m/s²
The velocity of the car at the end of the first 15 m
v - u + at
v = 0 + 5.21 x 2.4
v = 12.5 m/s
The time to cover the next 15 m;
d₂ = vt + ¹/₂at²
15 = 12.5t + (0.5 x 5.21)t²
15 = 12.5t + 2.61t²
0 = 2.61t² + 12.5t - 15
Use the formula method to solve the above quadratic equation.
a = 2.61
b = 12.5
c = -15
[tex]t = \frac{-b \ \ +/- \ \ \sqrt{b^2 - 4ac} }{2a} \\\\t = \frac{-12.5 \ \ +/- \ \ \sqrt{12.5^2 - (4\times 2.61 \times -15)} }{2\times 2.61}\\\\t = 0.9937 \ s \ \ \ or \ \ \ -5.78 \ s\\\\time \ can \ only \ be \ positive;\\\\t \approx \ 1\ s[/tex]
Therefore, the time it will take the car to travel the next 15 m is 1 s.
Sodium and ice a physical or chemical reaction
Answer:
physical change uwu owo hope this helps you uwu silly goose
The block A and attached rod have a combined mass of 50 kg and are confined to move along the guide under the action of the 796-N applied force. The uniform horizontal rod has a mass of 15 kg and is welded to the block at B. Friction in the guide is negligible.
Required:
Compute the bending moment M exerted by the weld on the rod at B. The bending moment is positive if counterclockwise, negative if clockwise.
Answer:
The bending moment is 459.16 N.m
Explanation:
From the given information;
Let's assume that the angle is 66°
Then, the free body diagram is draw and attached in the file below.
Now, the calculation of the acceleration from the first part of the free body diagram is:
[tex]\sum F_x = ma_x \\ \\ 796 - 50(9.81) sin 66=50a \\ \\ 796 - 448.094 = 50 a \\ \\ a = \dfrac{347.906}{50} \\ \\ a = 6.96 \ m/s^2[/tex]
Bending moment M:
From the second part of the diagram:
[tex]\sum M_B = mad \\ \\ M - (15 \times 9.81) (1.5) = (25 \times 6.96)(1.5 sin 66) \\ \\ M - 220.725 = 238.435 \\ \\ M = 238.435 + 220.725 \\ \\ \mathbf{M = 459.16 \ N.m}[/tex]
what must happen for a electromagnet to have a magnetic field
The diagram shows two
charged objects, X and Y.
Based on the field lines, what are the charges of the
objects?
X: positive
Y: negative
O X: negative
Y: positive
O x: negative
Y: negative
O x: positive
Y: positive
Answer:
X: positive
Y: positive
Explanation:
The electrical field lines have a specified direction based upon the sign of the charge. The electrical field lines have a direction coming out of the charge if the sign of the charge is positive. While the electrical field lines have a direction going inside the charge if the sign of the charge of negative.
It can be clearly seen in the diagram that the electric field lines are coming out of both charges. Therefore, both the charges are positive.
Hence, the correct option is:
X: positive
Y: positive