In the case of a coplanar system of loading, the internal resultant loading component at the section produced by the method of sections is zero. When cutting the piece for the coplanar loading method, there will be
What is coplanar door?
Coplanar refers to two surfaces that are installed absolutely flush with one another and signifies "put on the same plane." This is the leaf in relation to the architraves in our case, or
The MFU is a simple-to-install sliding door system that enables a door to close "flush" against the surrounding walls, giving it a neat and inconspicuous appearance and, if you so want, virtually concealing the door! No bottom track is necessary, allowing for a flooring run that is unobstructed.
Know more about method, Visit:
https://brainly.com/question/30076317
#SPJ1
the 2.8-kip load p is supported by two wooden members of uniform cross section that are joined by the simple glued scarf splice shown. determine the normal and shearing stresses in the glued splice.
The normal stress in the glued splice is 0.04 Ksi and the shearing stress is 0.07 Ksi.
The kip load p is supported by two wooden members of uniform cross section that are joined by the simple glued scarf splice. Normal stress and shearing stress are computed as follows:
sin60=5/x
x=5/sin60
A= 3 * x
= 3*5/sin60
=15/sin60
Normal stress will be computed as :
σ =P/A=1.4sin60/A
A= 15/sin60
σ=0.04 Ksi
Shearing stress will be computed as:
τ = Pcos60/A
A= 15/sin60
τ=0.04 Ksi
For further information regarding shear stress, click the link below:
brainly.com/question/12910262
#SPJ4
ifter ued for eparating coare particle of flour ugar baking powder powdered ingredient to retain finer texture
A sifter is used for separating coarse particles of flour, sugar, baking powder and other powdered ingredients to retain a finer texture.
What engineering principles are used to design an effective sifter? The design of an effective sifter involves a variety of engineering principles. One of the most important principles to consider is the material used for the sifter construction. Materials such as stainless steel, plastic, or specialty materials, such as mesh, should be chosen based on the application needs, such as the size range of the material, the desired sifting speed, or the degree of contamination in the material. The size of the sifter should also be taken into account, as the sifting efficiency is largely determined by the ratio of the size of the holes to the size of the material particles. This ratio should be optimized to ensure an effective sifting process. The sifter should also be designed with proper engineering principles in mind, such as the shape and size of the sifting chamber, the type of sifting mechanism, and the speed and power of the sifting process. Additionally, the sifter should be designed to prevent any material from clogging the sifter, which can lead to inefficiency. Finally, the sifter should be designed to accommodate any additional features, such as a dust collection system, that may be necessary for its intended use.To learn more about engineering principles refer to:
https://brainly.com/question/14725376
#SPJ4
determine the torque applied to the shaft of a car that transmits 225 hp and rotates at a rate of 3000 rpm.
Point E has a total internal loading of -3 kN. At point F, there is a +3 kN internal loading overall.
In mathematics and physics, a cross-sectional area is the non-empty intersection of a solid body in three dimensions with a plane, or its equivalent in higher dimensions. An item can be divided into several parallel cross-sections when it is chopped into pieces. The boundary of a three-dimensional cross-section that is parallel to the plane created by these axes and equal to two of the directions is also referred to as a contour line. Point E has a total internal loading of -3 kN. At point F, there is a +3 kN internal loading overall. The internal loadings acting on the cross section at E are mathematically given as, according to what we have. M e=-2400lbft. Typically, the mathematical equation for the equilibrium moment about b is written as
Learn more about Internal loading here:
https://brainly.com/question/30216823
#SPJ4
co2 (assume ideal gas) enters a steady flow device at a pressure of 1000 kpa, a temperature of 1000k, and negligible velocity. the gas expands adiabatically and leaves the steady flow device with a velocity of 125 m/s, a temperature of 700k, and a pressure of 100kpa. the cross sectional are at the exit is 0.1m2. find: (a) mass flow rate through the device, (b) power (watts) developed by this device
This device is an adiabatic steady flow device, which means that it does not exchange energy with the environment.
Find mass flow rate through the device?(a) Mass Flow RateMass Flow Rate = ρV A
ρ = gas density
V = velocity
A = area
Using the ideal gas law, we can calculate the gas density:
ρ = (P * M) / (R * T)
P = pressure (1000 kPa)
M = molar mass of the gas (44 g/mol)
R = ideal gas constant (8.314 J/mol K)
T = temperature (1000 K)
ρ = (1000 * 44) / (8.314 * 1000)
ρ = 5.34 kg/m3
Mass Flow Rate = (5.34 kg/m3)(125 m/s)(0.1 m2)
Mass Flow Rate = 6.675 kg/s
(b) PowerPower = Work/Time
Work = Force x Distance
Force = Pressure x Area
Distance = Velocity x Time
Pressure = (100 kPa)
Area = (0.1 m2)
Velocity = (125 m/s)
Time = (1 s)
Force = (100 * 0.1)
To learn more about Mass Flow Rate refer to:
https://brainly.com/question/24356835
#SPJ4
This is an adiabatic steady flow device, which implies it does not exchange energy with its surroundings.
How Determine the mass flow rate via the device?
(A)Rate of Mass Flow
V A = Mass Flow Rate
= density of gas
V stands for velocity.
A = area
We may determine the gas density using the ideal gas law:
Ρ = (P * M) / (R * T)
P stands for pressure (1000 kPa)
M = gas molar mass (44 g/mol)
R denotes the ideal gas constant (8.314 J/mol K).
T is for temperature (1000 K)
Ρ = (1000 * 44) / (8.314 * 1000)
Ρ = 5.34 kg/m3
(5.34 kg/m3)(125 m/s) Mass Flow Rate (0.1 m2)
6.675 kg/s is the mass flow rate.
(b)Strength
Work + Time = Power
Work Equals Force multiplied by Distance
Pressure x Area Equals Force
Distance Equals Speed x Time
Tensile strength = (100 kPa)
Area = (0.1 m2) (0.1 m2)
125 m/s = velocity
Time = (1 s) (1 s)
To learn more about exchange energy to refer:
https://brainly.com/question/17075670
#SPJ4
Name technology that combines selected physical disks into a managed logical group called a storage pool.
The technology that combines selected physical disks into a managed logical group called a storage pool is called Logical Volume Management (LVM).
LVM is a storage device management technology that allows users to combine multiple disks into a single logical storage unit, known as a storage pool, and then divide it into virtual disks or partitions called Logical Volumes. This makes it easier to manage and access data across multiple disks.
Logical Volume Management (LVM) is a method of managing disk space on Linux systems. It allows administrators to create logical volumes, which are collections of physical disks, and manage them as a single entity. With LVM, administrators can create, resize, and delete logical volumes without having to worry about the physical disks that make up the volume.
Learn more about Logical Volume Management :
https://brainly.com/question/28874890
#SPJ4
when the environment becomes more turbulent and unpredictable: [see p.15] group of answer choices strategy becomes less important than intuition strategy becomes an increasingly important as a source of direction external consultants need to play a greater role in strategy making strategy becomes an impossible exercise
Strategy becomes an increasingly important source of direction as the environment becomes more turbulent and unpredictable.
What is the primary source of strategy?The goal of strategy is to provide long-term direction and scope for an organization that achieves advantage in a changing environment through its configuration of resources and competencies with the goal of meeting stakeholder expectations.The degree to which a firm's external environment is unpredictable, uncertain, and volatile is referred to as environmental turbulence. It is defined more formally as the rate and unpredictability of changes in a firm's external environment.The degree to which an organization's resources and capabilities match the opportunities in the external environment is referred to as strategic fit. Because the matching occurs through strategy, it is critical that the company has the actual resources and capabilities to execute and support the strategy.To learn more about strategy refer to :
https://brainly.com/question/24462624
#SPJ4
what statement is accurate in regards to sharing workbooks?
One may choose to save an Excel workbook as a shared workbook if they wish to allow multiple people to work in the same spreadsheet at once.
Which of the following about sharing workbooks is true? Once data has been entered, users can add rows and columns, formulas, formatting, and formula changes.Important:You can collaborate on a workbook with many individuals using the older feature called "Shared Workbooks."Co-authoring has taken the place of this feature because of its numerous drawbacks.For Microsoft 365 members, Excel co-authoring is available in both the desktop client of the Excel program and Excel for the Web.The term "workbook" refers to a collection of worksheets of this type, whereas "worksheet" refers to a single page spreadsheet or page in Excel where you can write, edit, and change data.To learn more about workbooks refer
https://brainly.com/question/27960083
#SPJ4
because the practice of the basic movements of kata is the focus and mastery of self is the essence of matsubayashi ryu karate do i shall try to elucidate the movements of the kata according to my interpretation based on forty years of study it is not an easy task to explain each movement and its significance and some must remain unexplained to give a complete explanation one would have to be qualified and inspired to such an extent that he could reach the state of enlightened mind capable of recognijing soundless sound and shapeless shape i do not deem myself the final authority but my experience with kata has left no doubt that the following is the proper application and interpretation i offer my theories in the hope that the essence of okinawan karate will remain intact
Political movements and populist political figures include: The French Yellow Vest movement. The Italian Five-Star Movement.
A set of political ideologies known as populism emphasize the idea of "the people" and typically pits that group against "the elite." Anti-establishment and anti-political views are frequently associated with it. Recall that: The populist Yellow Vest movement in France, which started in 2018, was sparked by rising fuel prices and the government's apparent disregard for working-class concerns. The Five Star Organization is an Italian populist movement that was founded in 2009 and combines elements of right- and left-wing ideology. Matteo Salvini, the leader of Italy's right-wing Lega party, is known for pushing a populist agenda that prioritizes immigration restriction and the protection of Italian sovereignty.
Learn more about Populism here:
https://brainly.com/question/30182151
#SPJ4
Your manager is interested in looking at the number of engineers in different service lines across the business. Based on the data provided, what is the ratio of construction engineers to civil engineers?
Answer:
The answer is 1 to 2.44
I hope it helps.
Water flows at a rate of 0. 040 m3/s in a 0. 12-m-diameter pipe that contains a sudden contraction to a 0. 06-m-diameter pipe. Determine the pressure drop across the contraction section. How much of this pressure difference is due to losses and how much is due to kinetic energy changes?
Pressure drop in contraction section = 133 kPa. The pressure difference due to friction losses is = 39.7 kPa. Pressure difference due to kinetic energy changes = 93 kPa.
Find the pressure drop across the contraction section?
P is the pressure drop per 100 feet of pipe and the formula is P = 0.0668 V. D2.D is the inside diameter of the pipe measured in inches. Viscosity is expressed in centipoise (not SSU).
The Le/D approach simply increases the multiplier in equation (1) (i..L/D) with the length of the straight pipe (i..Le), which would cause a pressure drop equal to the connection losses, hence the term "equivalent length".
So ( L + Le ) /D is a multiplier.
The fluid flowing through the contraction (reduction in pipe diameter) causes an increase in velocity, resulting in a greater pressure drop than an equivalent straight pipe.
Pressure drop during contraction = 133 kPa.
Pressure difference due to friction losses = 39.7 kPa.
Pressure difference due to kinetic energy changes = 93 kPa.
For more information on pressure drop, see
brainly.com/question/14911964
#SPJ4
How to report interest income from the Internal Revenue Service?
Requires that most interest payments be reported on a 1099-INT tax form by the individual or entity making the payment. Most often this is a bank, other financial institution, or government agency.
What does payment mean?
One of the most popular forms of payment is cash (bills and change). ). .
Purchase will be made to buyer's account in the form of a personal check (US check). Debit Card: When a debit card is used to make a purchase, the buyer's account is charged immediately. Comparable to debit cards are credit cards. Payment occurs when agreed-upon amounts of products and services are exchanged for cash, goods, or services that are acceptable to all parties. Exchange of services, cash, cheques, wire transfers, credit and debit cards are all acceptable methods of payment.
Total pay applies to hourly, weekly, or daily pay plans used in place of overtime pay.
To learn more about payments, visit
brainly.com/question/26974810
#SPJ4
Nth root
Assign outValues with the nth root of the inValues. The root is specified by rootValue.
rootValue √ inValue Ex: If inValues is [4, 9, 16, 25] and rootValue is 2, then outValues = [2, 3, 4, 5]
This question uses a loop to iterate through an array and the Math.pow() method to calculate the nth root of a number.
The rfequired details for nth root of a number in given paragraph
Let outValues = [];
for (let i = 0; i < inValues.length; i++) {
out Values. push(Math.pow(inValues[i], 1/rootValue)); }
How do you find the nth root of a number?
The steps for this process are as follows:
1. Declare a variable called outValues and set it equal to an empty array.
2. Use a for loop to loop through the elements in the inValues array.
3. Inside the loop, use the Math.pow() method to calculate the nth root of the element in inValues.
4. Push the result of the Math.pow() method to outValues.
5. After the loop, outValues should now contain the nth root of each element in inValues.
To learn more about nth root of a number refer :
https://brainly.com/question/30375320
#SPJ4
what is the difference between a refrigerator and an air conditioner?
Refrigeration keeps cold air close, whereas air conditioning pushes it away and refrigeration uses only coolant, whereas air conditioning also uses outside air.
What is the use of refrigerator?The transfer of thermal energy from a cold temperature to a higher temperature occurs in refrigeration. Thermal energy is removed from the air in AC to keep it cool.The primary purpose of a refrigerator is to keep food cold. Cold temperatures keep food fresher for longer. The basic idea behind refrigeration is to slow down the activity of bacteria (which is present in all food) so that the bacteria take longer to spoil the food.Refrigerators and freezers can stand alone or be built into a kitchen. The refrigerator enables modern households to keep food fresher for longer periods of time than previously possible.To learn more about refrigerator refer to :
https://brainly.com/question/11014767
#SPJ4
every year you have a __% chance of being involved in an automobile accident.
Answer:
3%
Explanation:
the statistic states that 3% of licenced drivers are involved in accidents every year.As a result,the number of active drivers involved in accidents are greater than 3%
4.1 an a a battery, whose thevenin equivalent is a voltage source of 1.5 v and a resistance of 2 n, is connected to the terminals of an ideal diode. describe two possible situations that result. what are the diode current and tcnninal voltage when (a) the connection is between the diode cathode and the positive terminal of the battery and (b) the anode and the positive terminal are connected?
The cathode is the diode's negative terminal, or n-side. When the Current is 0.75A, then Voltage will be 1.5 V .
What is the current that passes through the diode?
As a result, the n-side of the diode is connected to the positive terminal of the battery in this case. This is the reverse bias condition, when no current flows through the diode and the diode acts as an open circuit. In this case:
Id = 0 A = current through diode
Vd = 1.5 V = Voltage Across Diode
B. The anode is the diode's positive terminal, or p-side. As a result, the p-side of the diode is connected to the positive terminal of the battery in this case. When current flows through the diode and the diode acts as a closed circuit, this is the condition for forward bias. In this case, the ideal diode acts as a short circuit and has the following properties:
The current that passes through the diode:
Id = V/R
= 1.5 V/2 Ω = 0.75A
To learn more about current refer to :
brainly.com/question/1100341
#SPJ4
part 1. implementing basic combinational logic gates on the de10-lite board following the example given in part 0, create a new project and implement some logic gates of your choice using the switches, buttons, leds and 7-segment displays on the de10-lite board. download your design and verify proper operation. there are many possible design options. a few examples are 2-, 3- or 4-input and, nand, or, nor gates. you could also use a pushbutton to directly control an led or segment of a 7-segment display. note that the segments of the 7-segment display are active-low, as shown in figure 9, and bit 7 corresponds to the decimal point. for example, in order to turn off all the segments of the hex0 7-segment display and keep them off, you could use the following assign statement:
The truth table is the main tool to capture logical relationships in a concise and universal way.
What is a segment?
A segment is a customer Data Platform (CDP), which means it provides a service that simplifies the collection and use of user data from your digital assets (websites, applications, etc.). Thanks to Segment you can collect, transform, send and store your data. By incorporating new tools, the lets you spend more time consuming data and less time collecting it. You can also enrich the collected customer data by combining data from other tools and then aggregating it to monitor performance, make decisions and create unique, personalized user experiences.
You can also use Profile, the Segment Identity Recognizer, which allows you to unify individual user data for a holistic understanding of their activities.
To learn more about decision making, visit:
brainly.com/question/1249089
#SPJ4
SCI material can be processed on SIPRNET if the content is Secret/SCI.
True or False
SCI content that is secret may be processed over Siprnet. This assertion is untrue.
What is a sensitive compartmented information SCI program quizlet?An application that separates multiple categories of classified information into unique compartments for increased security and distribution or distribution control.The material must be kept in a pouch or briefcase with a lock that can be opened with a key that is made of canvas or another sturdy material. Decisions on derivative classification must be based on specific information.The aim of this yearly SIPRNET refresher training is to make sure that all MEDCOM SIPRNET users are aware of their duties for the security of sensitive information and systems in line with applicable Army rules and MEDCOM policy on SIPRNET Security Procedures. Standards for eligibility to access SCI are set by the DNI.To learn more about SCI refer to:
https://brainly.com/question/28416408
#SPJ4
The vertical force F acts downward at A on the twomembered frame. Determine the magnitudes of the two components of F directed along the axes of AB and AC. Set F = 500 N. Solve problem 4 with F = 350 lb.
Vector addition parallelogram law :If a force F needs to be broken down into its component parts along the axes b and c, one should start at the head of the force and build lines parallel to the axes until a parallelogram is formed.
Solve the problem ?Vector addition parallelogram law :If a force F needs to be broken down into its component parts along the axes b and c, one should start at the head of the force and build lines parallel to the axes until a parallelogram is formed.
The parallelogram's sides are represented by Fb and Fc.
Finding the force component F AB and F AC applied at diagram point A is our task.
We can employ the law of sines, as shown in the diagram.
The query is unfinished.
The entire question is included as an image in the attachment, and an explanation is given below.
F AB / sin 60 = 500/ sin 75
F AB = 500/0.965*0.866
F AB = 448.7 N
To find F AC
F AC /sin 45 =500 /sin 75
F AC = 500/0.965* 0.7071
F AC = 366.3 N
To learn more about Vector addition parallelogram law refer
https://brainly.com/question/14436845
#SPJ4
A motor car reaches a velocity of 17 m/s from rest. Draw a velocity-time graph and determine the acceleration.
The automobile initially accelerates for 5 seconds. As a result, the velocity-time graph initially slopes and then maintains a constant speed.
What is velocity of time ?Your understanding of velocity and its scientific definition are probably similar. You are aware that a big displacement over a short period of time corresponds to a large velocity, and that velocity is measured in terms of the speed of objects in terms of miles an hour or kilometres per hour. The shift in position multiplied by the distance travelled is how average velocity is calculated. Velocity and speed describe how quickly or slowly a moving object moves. We frequently encounter circumstances when we must determine which of two or more moving objects is going faster. If the two are travelling on the same route in the same direction, it is simple to determine which is quicker.
To know more about velocity of time visit:
https://brainly.com/question/18358954
#SPJ1
The output of a power supply is assumed to be normally distributed. 16 observations taken at random on voltage are as follows: 10. 35, 9. 30, 10. 00, 9. 96, 11. 65, 12. 00, 11. 25, 9. 58, 11. 54, 9. 95, 10. 28, 8. 37, 10. 44, 9. 25, 9. 38 and 10. 85. (a) Test the hypothesis that the mean voltage equals 12V against a two-sided alternative using α=0. 5. (b)Construct a 95% confidence interval on µ. (c) Test the hypothesis that σ2 =1 using α=0. 5. (d)Construct a 95% two-sided confidence interval on σ. (e) Construct a 95% upper confidences interval on σ
As the typical value can be represented by the mean, it acts as a benchmark for all observations.
Explain about the Mean?A dataset's mean (also known as the arithmetic mean, which differs from the geometric mean) is calculated by dividing the sum of all values by the total number of values. It is frequently referred to as the average and is the most widely used measure of central tendency.
The mean is the average or most frequent value among a set of numbers. It is a statistical measure used to determine the median and mode of a probability distribution's central tendency. It is additionally known as an expected value.
Finding the "average" value involves adding up all the data points and dividing by the total number of data points.
Use the R codes listed below to replicate the answers:
d = c(10.35, 9.30, 10.00, 9.96, 11.65, 12.00, 11.25, 9.58, 11.54,
9.95, 10.28, 8.37, 10.44, 9.25, 9.38, 10.85)
mean(d)
sd(d)
se = sqrt(length(d)) / sd(d)
se
Mean(d) - 1.96* se = CIl
mean(d) + 1.96* se CIU
CI = c (CIl, CIU)
To learn more about Mean refer to:
https://brainly.com/question/1136789
#SPJ4
He proposed grading at a project site will consist of 25,100 m3 of cut and 23,300 m3 of fill and will be a balanced earthwork job. The cut area has an average moisture content of 8. 3%. The fill will be compacted to an average relative compaction of 93% based on a maximum dry unit weight of 18. 3 kN/m3 and an optimum moisture content of 12. 9% obtained from the modified Proctor test. Compute the volume of water in kiloliters that will be required to bring these soils to the optimum moisture content
The volume of water in kiloliters that will be required to bring these soils to the optimum moisture content is 1859 kL .
What is the volume of water ?Knowing that;
Cut volume: 25,100 m3
23,300 m3 of dry dirt were filled.
The soil's weight will be;
⇒ 93% × 18.3 kN/m³ × 23,300 m³
= 0.93 × 426390 kN 3
= 396,542.7 kN
12.9% is the ideal moisture percentage.
Moisture needed is equal to (12.9 - 8.3%%)% = 4.6%
So,
Water needed weight = 4.6% x 396,542.7 = 18241 kN
Water needed is equal to 18241 / 9.81, or 1859 m3.
1859 kL of water are needed.
Consequently, 1859 kL of water will be needed to bring these soils to the ideal moisture level.
In order to get these soils to the ideal moisture level, 1859 kL of water will be needed.
To learn more about volume refer to:
https://brainly.com/question/22212556
#SPJ4
to perform a thorough inspection of brake pads, you should do all of the following except: group of answer choices inspect the pads to see if they are wearing evenly. inspect all pads, retaining hardware, and anti-noise shims. measure the remaining brake pad thickness and compare to specifications. measure the pad-to-caliper piston clearance.
Answer:
measure the pad-to-caliper piston clearance.
Determine The Relationship Between Peak-To-Peak And Rms Voltage For A Sinusoidal Waveform
The Relationship between Peak-To-Peak and RMS Voltage is that V peak-peak voltage is of a sine wave is the RMS value multiplied by 2√2. For sinusoidal voltages V p-p=V RMS × 2√2
In the above mentioned equation V p-p is the peak-to-peak voltage and V RMS is the RMS voltage. D-Peak indicates the maximum value that the current or voltage reaches in alternating current.
However, RMS indicates the average value of current or voltage. They are used in thermodynamics. For example, to express the average velocity of gas molecules.
When AC current voltage values are given, RMS values are usually given.
The RMS value will always be less than the peak value.
For further information regarding peak-to-peak voltage, click the link below:
brainly.com/question/14544755
#SPJ4
A full brake-by-wire system does away with the hydraulic portion of the brake system and replaces it with all of the following EXCEPT: Sensors, wires, and electronic control unit, or mechanically actuated motors
The correct answer is C) mechanically actuated motors. A full brake-by-wire system replaces the hydraulic portion of the brake system with sensors, wires, and an electronic control unit, but not mechanically actuated motors.
Instead, the brake system is actuated through electrical means, such as electric motors, digital computers, or fiber optic cables.
Mechanically actuated motors are motors that use mechanical force, such as a spring, to drive the motor. These motors are used in a variety of applications, from toys to industrial machinery, and can be found in a wide range of sizes and shapes. Mechanically actuated motors have several advantages over other types of motors, such as low cost, low maintenance, and the ability to produce high torque at low speeds.
Learn more about electrical :
https://brainly.com/question/24786034
#SPJ4
FILL IN THE BLANK. Traditional file systems use ________, files, and documents.
Traditional file systems use directories, files, and documents. Directories are used to organize files and documents into a hierarchical structure.
Files are the actual data stored in the file system, and documents are the files that contain text or other information. Directories are used to organize files and documents into a hierarchical structure, which makes it easier to find and access the data stored in the file system. Files are the actual data stored in the file system, and documents are the files that contain text or other information. Documents can be used to store text, images, audio, video, and other types of data. Directories are organized into a hierarchical structure, with each directory containing one or more subdirectories. Each subdirectory can contain files and documents, and each file and document can contain data. The hierarchical structure of the file system makes it easier to find and access the data stored in the file system.
Learn more about Traditional files here
https://brainly.com/question/20292126
#SPJ4
0. What percentage of traffic congestion is due to incidents?
The percentage of traffic congestion that is due to incidents will be 20%.
How to calculate the percentage?A percentage simply has to do with the a value or ratio which can be stated as a fraction of 100. It should be noted that when we want to we calculate a percentage of a number, we simply divide it and then multiply the value that is gotten by 100.
In this case, the number of traffic congestion that occured in a month is 20 times and 4 are due to incidents.
The percentage of traffic congestion that is due to incidents will be:
= 4 / 20 × 100
= 20%
Learn more about percentages on
brainly.com/question/24877689
#SPJ1
The number of traffic congestion that occured in a month is 20 times and 4 are due to incidents. What percentage of traffic congestion is due to incidents?
Which of the following methods may be used to install new wheel studs?
answer choices
A. Draw in or pull in
B. Draw out or slide in
C. Draw out or push in
D. Draw in or press in
D. Draw in or press in. This method is used to install new wheel studs because it is the most secure and reliable way to install them. The stud is inserted into the wheel hub and then pressed in with a press or hammer.
There are several methods that may be used to install new wheel studs. The most common method is to draw in or press in the stud. This involves inserting the stud into the wheel hub and then pressing it in with a press or hammer. This ensures that the stud is securely in place and will not come loose or move. Another method is to draw out or slide in the stud. This involves inserting the stud into the wheel hub and then sliding it in until it is flush with the hub. This method is less secure than the press-in method, but it is still effective. Finally, the draw out or push in method involves inserting the stud into the wheel hub and then pushing it in until it is flush with the hub. This method is the least secure of the three, but it is still effective.
Learn more about wheel studs here
https://brainly.com/question/7650277
#SPJ4
the board is subjected to a tensile force of 300lb. determine the average normal and average shear stress in the the wood fibers
The average normal and average shear stress in the the wood fibers are 23.29 and 12.052
Tensile force =300lb
Σfx=0: V-300 cos20°=0 F = force
v=281.90 l b V = value
Σf^4: N-300sin20°=0 N = number of units
N=102.606 l b
A=2(4/SIN20)=23.39IN^ 2 A = average normal
σ=N/A= 102.606/23.39=4.386 PSI. σ = standard deviation
V/A=281.90/23.39=12.052 Psi. Average sher stress
Tensile force refers to the stretching forces that act on a material and consists of two components: tensile stress and tensile strain. This means that the material being acted upon is under tension, and the forces are attempting to stretch it.
When a tensile force is applied to a material, a stress corresponding to the applied force develops, contracting the cross-section and elongating the length.
To learn more about tensile force
https://brainly.com/question/17077464
#SPJ4
the minimal number of cells expected in sequencing to enable statistically relevant numbers for the cells having the lowest occurence in the suspension
Depending on the experiment and the anticipated percentage of rare cells in the sample, the precise number of cells needed for sequencing to produce statistically significant results will change. To achieve appropriate coverage of rare cell populations, it is typically advised to sequence at least 10,000 cells per sample.
Depending on the experiment and the anticipated percentage of rare cells in the sample, the precise number of cells needed for sequencing to produce statistically significant results will change. In order to provide appropriate coverage of rare cell populations, it is generally advised to sequence at least 10,000 cells per sample. This is due to the fact that populations of rarer cells will probably have lower counts than populations of more abundant cells, therefore sequencing fewer cells may cause the proportions of rare cells to be underestimated. Additionally, by supplying a bigger sample size for statistical analysis, sequencing more cells can also improve the data's correctness and dependability.
Learn more about coverage here-
https://brainly.com/question/29414893
#SPJ4
In C, Given positive integer numInsects, write a while loop that prints that number doubled repeatedly without exceeding 100. Follow each number with a space. After the loop, print a newline.Example: If numInsects = 8, your code should print:8 16 32 64
We first declare and initialize the variables numInsects and currentNum to the starting value of numInsects.
What is the program for while loop c code?We then enter a while loop that continues as long as currentNum is less than or equal to 100.Inside the loop, we use printf to print the current value of currentNum followed by a space.We then double the value of currentNum by multiplying it by 2.The loop continues until currentNum exceeds 100, at which point the loop exits.Lastly, we use printf to print a newline to end the output.In this example, the code will print: 8 16 32 64 (as the value of currentNum is doubled repeatedly without exceeding 100)int numInsects = 8;while (numInsects <= 100) { printf("%d ", numInsects); numInsects *= 2;}printf("\n");To learn more about while loop refer:
brainly.com/question/30357299
#SPJ4
The while loop is used to loop through a block of code until a condition is met.
What is the program using while loop?In most computer programming languages, a while loop is a type of control flow statement that allows code to be executed repeatedly based on a given Boolean condition. While loops are similar to looping if statements.The while statement initiates a loop in which the specified statement is executed until the test condition is false. The condition is evaluated after the statement is executed, resulting in at least one execution of the specified statement.The program that prints number doubled repeatedly till 100 using while loop is as follows :
num_insects = 8
while num_insects <= 100:
print(num_insects,'', end="")
num_insects = num_insects * 2
print("") # newline
To learn more while loop refer to :
brainly.com/question/19344465
#SPJ4