If a 2 1/8 inch diameter medium carbon steel rod is to be turned between centers to a 2 inch diameter using high speed cutting bits without using a coolant, find the following:

Picture linked

Answer:

Explanation:

7. False

8. True

9. True

10.True

11. True

Answer:

carried courage buried

Explanation:

its Filipino

Answer:

72 MPa

Explanation:

Critical resolved shear stress = 36 MPa

calculate the maximum possible yield strength for a single crystal of the metal

first we have to express the critical resolved shear stress as

бy = 2т[tex]_{critical}[/tex]

given that the minimum stress needed to introduce yielding curve will occur  at Ψ = λ = 45

where : бy = yielding stress

             t[tex]_{critical}[/tex] = 36MPa

therefore the maximum possible yield strength

= (2) * (36)

= 72 MPa

Answer:

  no

Explanation:

No. More power is dissipated when the transistor is in its active region. In general, transistors in switching circuits are biased either "on" or "off". Time spent in the active region is minimized.

_____

On the other hand, speed can be enhanced if the transistors are active. So, it's a speed/power trade-off. Usually power is of more interest, particularly when there are millions of switching circuits. However, in certain applications, speed may be the priority, so the transistor will be biased in its active region.

Answer:

- weather refers to short-term changes in the atmosphere

- climate describes what the weather is like over a long period of time in one area.

Answer:

a Network Engineer (architect)

Explanation:

Indeed, as a Network Engineer, we would expect Nicole to be in charge of planning, setting up, and managing the software and hardware components of the computer networks so that they function as intended.

A Network Engineer therefore would be responsible for setting up the networking capabilities and policies that will govern the workstations when connected to the company network.

Answer:

Your mobile phone has more computing power than the computers used for the Apollo 11 moon landing.

Mobile phones have to “work harder” to get a signal if you are in a moving vehicle.

The first mobile phone was made in 1973.

The first mobile phones that went on sale in 1983 cost nearly $4,000 each.

In 2012 Apple sold 340,000 phones per day.

4 out of 10 Brits admit to snooping on their partners phone.

Out of the 53% of snoopers that found incriminating evidence on their partner’s phone, 5% went on to terminate their relationship.

Waterproof mobile phones came to market because Japanese youngsters like to use them in the shower.

Apparently mobile phones have 18 times more bacteria on them than toilet handles!

Phubbing describes the act of snubbing someone by using your mobile phone in their company.

In 2015 more people died from taking selfies than shark attacks.

Teenagers that use a phone more than 2 hours a day increase their risk of depression and anxiety.

Nomobophobia is severe anxiety caused by the thought or act of losing your phone or running out of battery.

Explanation:

Answer:

a) According to the maximum-shear-stress failure theory, the static factor of safety of the shaft is 2.440.

b) According to the distortion-energy failure theory, the static factor of safety of the shaft is 2.816.

Explanation:

First, we need to determine the torque experimented by the shaft ([tex]T[/tex]), measured in kilonewton-meters, whose formula is described:

[tex]T = \frac{\dot W}{\omega}[/tex] (Eq. 1)

Where:

[tex]\dot W[/tex] - Power, measured in kilowatts.

[tex]\omega[/tex] - Angular velocity, measured in radians per second.

If we know that [tex]\dot W = 10\,kW[/tex] and [tex]\omega = 20.944\,\frac{rad}{s}[/tex], then the torque experimented by the shaft:

[tex]T = \frac{10\,kW}{20.944\,\frac{rad}{s} }[/tex]

[tex]T =0.478\,kN\cdot m[/tex]

Let consider that shaft has a circular form, such that shear stress is determined by the following formula:

[tex]\tau = \frac{16\cdot T}{\pi\cdot D^{3}}[/tex] (Eq. 2)

Where:

[tex]D[/tex] - Diameter of the shaft, measured in meters.

[tex]\tau[/tex] - Torsional shear stress, measured in kilopascals.

If we know that [tex]D = 0.03\,m[/tex] and [tex]T =0.478\,kN\cdot m[/tex], the torsional shear stress is:

[tex]\tau = \frac{16\cdot (0.478\,kN\cdot m)}{\pi\cdot (0.03\,m)^{3}}[/tex]

[tex]\tau \approx 90164.223\,kPa[/tex]

a) According to the maximum-shear-stress failure theory, we get that maximum shear stress limit is:

[tex]S_{ys} = 0.5\cdot S_{ut}[/tex] (Eq. 3)

Where:

[tex]S_{ys}[/tex] - Ultimate shear stress, measured in kilopascals.

[tex]S_{ut}[/tex] - Ultimate tensile stress, measured in kilopascals.

If we know that [tex]S_{ut} = 440\times 10^{3}\,kPa[/tex], the ultimate shear stress of the material is:

[tex]S_{ys} = 0.5\cdot (440\times 10^{3}\,kPa)[/tex]

[tex]S_{ys} = 220\times 10^{3}\,kPa[/tex]

Lastly, the static factor of safety of the shaft ([tex]n[/tex]), dimensionless, is:

[tex]n = \frac{S_{ys}}{\tau}[/tex] (Eq. 4)

If we know that [tex]S_{ys} = 220\times 10^{3}\,kPa[/tex] and [tex]\tau \approx 90164.223\,kPa[/tex], the static factor of safety of the shaft is:

[tex]n = \frac{220\times 10^{3}\,kPa}{90164.223\,kPa}[/tex]

[tex]n = 2.440[/tex]

According to the maximum-shear-stress failure theory, the static factor of safety of the shaft is 2.440.

b) According to the distortion-energy failure theory, we get that maximum shear stress limit is:

[tex]S_{ys} = 0.577\cdot S_{ut}[/tex] (Eq. 5)

If we know that [tex]S_{ut} = 440\times 10^{3}\,kPa[/tex], the ultimate shear stress of the material is:

[tex]S_{ys} = 0.577\cdot (440\times 10^{3}\,kPa)[/tex]

[tex]S_{ys} = 253.88\times 10^{3}\,kPa[/tex]

Lastly, the static factor of safety of the shaft is:

[tex]n = \frac{253.88\times 10^{3}\,kPa}{90164.223\,kPa}[/tex]

[tex]n = 2.816[/tex]

According to the distortion-energy failure theory, the static factor of safety of the shaft is 2.816.

Answer:

The estimated batching production is 210 cy/hr

Explanation:

Given;

capacity of the batching chamber of the plant, Q = 12.5 cy

average batching cycle time, t = 3 min

plant efficiency, n = 84 %

The estimated batching production is calculated as efficiency of the machine multiplied by the production rate in hour. This is given by the solution below;

Batching production = (nQ )/ t

[tex]Batching \ production = 0.84(\frac{12.5 \ cy}{3 \ min} *\frac{60 \ min}{1 \ hr})\\\\ Batching \ production = 210 \ cy/hr[/tex]

Therefore, the estimated batching production is 210 cy/hr

Answer:

Speed V1 at the beginning of the skid  = 57.075 mph

Explanation:

Calculate the V1 speed at the beginning of the skid

V1 ( speed before brake was applied ) = ?

distance travelled by Vehicle 1 = 195 ft

curve tangent for vehicle 1 =  - 3% = - 0.03

coefficient of friction = 0.48

speed at Impact = 25 mph

To determine the V1 speed at the beginning of the skid we have to apply AASTHO

d1 = [tex]( \frac{VA^{2} - VA^{12} }{30(F+N)} )[/tex]

195 =  [tex](\frac{VA^2- 25^2}{30(0.48-0.03)} )[/tex]

Hence : VA = 57.075 mph

Answer:

116,090 Btus

Explanation:

Answer:

Option B: An MSDS

Explanation:

A dictionary is used to check up the meaning of general words and not for checking if a substance being used is hazardous. Option A is wrong.

MSDS means "Material Safety Data Sheet" and it contains documents with information that relates to occupational health & safety for checking various substances and products. Thus, option B is correct.

SAE stands for Society of Automotive Engineering and their standards pertain to mainly Automobiles. Thus option C is wrong.

EPA guidelines are mainly for checking facility and environmental health and safety compliance. Thus, option D is wrong.

Answer:

The answer is below

Explanation:

Absolute temperature is the temperature of a body with reference to 0 as the absolute zero.

English system of measurement are measurements used in united states while the S.I units are units that are universally accepted.

The temperature scale in S.I are Celsius (°C) for ordinary temperature and kelvin(K) for absolute temperature while the temperature scale in English system is Fahrenheit (°F) for ordinary temperature and Rankine (R) for absolute temperature.

The information regarding the ordinary and absolute temperature scales in the SI and the English system is as follows:

Learn more: brainly.com/question/17429689

Answer:

Resolution of Fourier transform = 2Hz

Explanation:

Given:

Sample signals = 16,384 samples/second

Number of data points = 8,192 oints

Find:

Resolution of Fourier transform

Computation:

Resolution of Fourier transform = fs / N

Resolution of Fourier transform = 16,384 / 8,192

Resolution of Fourier transform = 2Hz

Answer:

The moment of inertia of the rotor is approximately [tex]1.105\times 10^{-6}[/tex] kilogram-square meters.

The rotor inertia may differ from these assumption due to differences in the shape of cross section.

Explanation:

We assume that rotor can be represented as a solid cylinder of radius [tex]r[/tex], length [tex]l[/tex], made of cooper ([tex]\rho = 8960\,\frac{kg}{m^{3}}[/tex]) and whose axis of rotation passes through its center of mass and is parallel to its cross section. By definition of Moment of Inertia and Theorem of Parallel Axes, the moment of inertia of the rotot is:

[tex]I = \frac{1}{4}\cdot \rho \cdot \left(\frac{\pi}{4} \right) \cdot R^{3}\cdot (3\cdot R^{2}+L^{2})[/tex]

[tex]I = \frac{\pi}{16}\cdot \rho \cdot R^{3}\cdot (3\cdot R^{2}+L^{2})[/tex] (Eq. 1)

Where:

[tex]\rho[/tex] - Density of copper, measured in kilograms per cubic meter.

[tex]R[/tex] - Radius of the rotor, measured in meters.

[tex]L[/tex] - Length of the rotor, measured in meters.

[tex]I[/tex] - Moment of inertia, measured in kilogram-square meters.

If we know that [tex]\rho = 8960\,\frac{kg}{m^{3}}[/tex], [tex]L = 25\times 10^{-3}\,m[/tex] and [tex]R = 8.98\times 10^{-3}\,m[/tex], the estimated moment of inertia of the rotor is:

[tex]I = \frac{\pi}{16}\cdot \left(8960\,\frac{kg}{m^{3}} \right)\cdot (8.98\times 10^{-3}\,m)^{3}\cdot [3\cdot (8.98\times 10^{-3}\,m)^{2}+(25\times 10^{-3}\,m)^{2}][/tex]

[tex]I \approx 1.105\times 10^{-6}\,kg\cdot m^{2}[/tex]

The moment of inertia of the rotor is approximately [tex]1.105\times 10^{-6}[/tex] kilogram-square meters.

From D'Alembert's Formula we know that net force of rigid bodies experimenting rotation equals the product of moment of inertia and angular acceleration. In this case, the purpose is minimizing moment of inertia and it is done by modifying the shape of the cross section so that rotor could be aerodynamically more efficient.

Answer:Modulus of Elasticity (E)-------- A

Explanation:

The modulus of elasticity, Young's modulus E is a measure of a material's stiffness or resistance to being elastically deformed when stressed or due to tension According to  Hook's law the modulus of elasticity is defined as the ratio of the stress to the strain and defined as the slope of its stress-strain region  in the stress and strain graph.

--The stiffer a material, the higher the elastic modulus and vice versa for a less stiff material.

it can be calculated with this formulae

Young’s modulus equation is E = tensile stress/tensile strain

= (FL) / (A X change in L)

where F = applied force,

L = initial length,

A = square area,

E = Young’s modulus in Pascals (Pa).