How is a parallel circuit different from a series circuit?

Answer:

Dry ice

Explanation:

Answer:

The lava doesn't melt through ice because the steam ice sits on top of a blanket of steam rather than on top of the ice itself. This means the friction between the lava and the ice is very low.

Explanation:

Answer:

3.7 L

Explanation:

Initial volume (V₁) = 3.3 L

Initial pressure (P₁) = 100 KPa

Final pressure (P₂) = 90 KPa

Final volume (V₂) =?

The final volume of the gas can be obtained by using the Boyle's law equation as follow:

P₁V₁ = P₂V₂

100 × 3.3 = 90 × V₂

330 = 90 × V₂

Divide both side by 90

V₂ = 330 / 90

V₂ = 3.7 L

Thus, the final volume of the gas is 3.7 L

Answer:

39.4 Liters

Explanation:

Using the general gas law equation as follows:

PV = nRT

Where;

P = pressure (atm)

V = volume (L)

n = number of moles (mol)

R = gas law constant (0.0821 Latm/molK)

T = temperature (K)

According to the information provided in this question;

P = 1.25atm

V = ?

T = 300K

n = 2.00mol

Using PV = nRT

V = nRT/P

V = (2 × 0.0821 × 300) ÷ 1.25

V = 49.26 ÷ 1.25

V = 39.41

V = 39.4 Liters

Answer: Helianthus L. Sunflower

Explanation:

Answer: Helianthus L.

Explanation:

Answer:

Volcanoes cool off the earth by emitting heat from its interior. They also add islands and for example, Hawaii was created / is made out of volcanoes. The deposits from volcanoes can also be used for building materials. Volcanic explosions have caused the atmosphere and oceans to form. Volcanic deposits also create land which is fertile.

Answer:

2 lol

Explanation:

Answer:

True

Explanation:

The bigger mass is measured in kilograms and smaller in grams

Answer:

A hypothesis, such as one about cells, usually becomes a theory.

Explanation:

Maybe this information is helpful:

The features of the ocean floor are not permanent, and are gradually changing over time due to the movement of tectonic plates. Most of the ocean floor features from close to where the plates are shifting either towards or away from each other. Marine ecosystems are found around parts of the ocean floor features, even the Mariana Trench, which is the deepest trench in the world.

Answer:

I love it

Explanation:

☁️ Answer ☁️

annyeonghaseyo!

Your answer is:

When electrons are lost, a positively charged ion is formed. When electrons are gained, a negatively charged ion is formed. (I like the car)

Hope it helps.

Have a nice day noona/hyung!~ ￣▽￣❤️

The number of moles of solute in a solution is the product of the molarity and volume of the solution. The number of moles in 0.045 L of 0.465 M potassium bromide is 0.0209 mol. Hence, option A is correct.

Molarity of a solution is the ratio of its number of  moles of solute to the volume of solution in liters. Molarity is the most common term used to express the concentration of  a solution.

Molarity is a colligative property thus depends on the amount of substance and it is temperature dependant.

molarity = no.of moles/ volume in L

Given that volume of the potassium bromide solution = 0.045 L

molarity = 0.465 M

then, number of moles of potassium bromide solute = molarity × volume

no.of moles  = 0.465 M × 0.045 L = 0.0209 mol.

Therefore, there are 0.0209 moles of potassium bromide is present in the solution.

To find more on molarity, refer here:

https://brainly.com/question/8732513

#SPJ2

Wind direction is reported by the direction from which it originates. For example, a north or northerly wind blows from the north to the south. Wind direction is usually reported in cardinal (or compass) direction, or in degrees.

Answer:

1 mole of lithium is 7 grams. we know this from it's relative molecular mass.

if 1 mole is 7 grams then x moles is 0.56 grams

we can equate them by saying (1/x)=(7/0.56)

after cross multiplying, we get 7x=0.56, x will be equals to 0.56/7

x=0.08 grams

0.08 mole is your answer

Answer:

we have

1 mole of li =7g

now

5.6×10^-1g of li =1mole/7g×5.6×10^-1 g=0.08mole

Answer:

See explanation

Explanation:

Fossil fuels are formed from the remains of plants and animals that have been subjected to intense pressure during the carboniferous era. These plants and animal remains undergo the process of fossilization to yield the fossil fuels we have today such as crude oil.

Living organisms are composed of elements which include nitrogen and sulphur. Since these fuels originated from dead organisms, they also contain these elements found in living organisms.

Hence, fossil fuels such as; coal, crude oil, and natural gas contain 0.05%-0.5% sulfur and 0.5%-2.1% nitrogen.

Answer: 0.245 m/s

Explanation:

So velocity = d/t or distance over time in this case m/s or meters per second. But BE CAREFUL you must remember to convert cm to m always so 135 cm= 1.35m and 1.35m/5.5s= 0.245m/s

Answer:Resistor Basics

Resistors are electronic components which have a specific, never-changing electrical resistance. The resistor's resistance limits the flow of electrons through a circuit.

They are passive components, meaning they only consume power (and can't generate it). Resistors are usually added to circuits where they complement active components like op-amps, microcontrollers, and other integrated circuits. Commonly resistors are used to limit current, divide voltages, and pull-up I/O lines.

Resistor units

The electrical resistance of a resistor is measured in ohms. The symbol for an ohm is the greek capital-omega: Ω. The (somewhat roundabout) definition of 1Ω is the resistance between two points where 1 volt (1V) of applied potential energy will push 1 ampere (1A) of current.

As SI units go, larger or smaller values of ohms can be matched with a prefix like kilo-, mega-, or giga-, to make large values easier to read. It's very common to see resistors in the kilohm (kΩ) and megaohm (MΩ) range (much less common to see miliohm (mΩ) resistors). For example, a 4,700Ω resistor is equivalent to a 4.7kΩ resistor, and a 5,600,000Ω resistor can be written as 5,600kΩ or (more commonly as) 5.6MΩ.

Schematic symbol

All resistors have two terminals, one connection on each end of the resistor. When modeled on a schematic, a resistor will show up as one of these two symbols:

Resistor schematic symbols

Two common resistor schematic symbols. R1 is an American-style 1kΩ resistor, and R2 is an international-style 47kΩ resistor.

The terminals of the resistor are each of the lines extending from the squiggle (or rectangle). Those are what connect to the rest of the circuit.

The resistor circuit symbols are usually enhanced with both a resistance value and a name. The value, displayed in ohms, is obviously critical for both evaluating and actually constructing the circuit. The name of the resistor is usually an R preceding a number. Each resistor in a circuit should have a unique name/number. For example, here's a few resistors in action on a 555 timer circuit:

Answer: resistor is

Explanation:

A resistor controls the flow of the electrical current within a circuit. Resistors are made from materials like copper or carbon, which make it difficult for the electrical charges to flow through a circuit. The most common type of resistor is a carbon resistor, which is a general purpose resistor, best suited for lower-powered circuits.

i think Neuterons i am right

Answer:

I do not know srry

Explanation:

Answer:

A. 6atm

Explanation:

Using pressure law equation:

P1/T1 = P2/T2

Where;

P1 = initial pressure (atm)

T1 = initial temperature (K)

P2 = final pressure (atm)

T2 = final temperature (K)

According to this question;

P1 = 3 atm

P2 = ?

T1 = 120K

T2 = 240K

Using P1/T1 = P2/T2

3/120 = P2/240

Cross multiply

240 × 3 = P2 × 120

720 = 120P2

P2 = 720/120

P2 = 6atm

Answer:

10 watts

Explanation:

Power = Work / Time

Power = 330 J / 33 s

Power = 10 watts

Explanation:

In chemistry, thermodynamics, and many other related fields, phase transitions (or phase changes) are the physical processes of transition between the basic states of matter: solid, liquid, and gas, as well as plasma in rare cases.

Answer:

In chemistry, thermodynamics, and many other related fields, phase transitions are the physical processes of transition between the basic states of matter: solid, liquid, and gas, as well as plasma in rare cases. A phase of a thermodynamic system and the states of matter have uniform physical properties.

Explanation:

Answer:

Increase the concentration of the reactants.

Explanation:

This question seems vague, but to put it simply, the reaction rate decreases with a decrease in temperature, so we need to find a way to increase the reaction rate again. When you lower temperature, the molecules are slower and collide less. So therefore, in other words, we need to find a way to increase the rate of collisions between molecules. When the temperature drops, if we increase the concentration of the reactants, we are able to increase the rate of collisions between molecules. As a result, reaction rate is increased once again.

If the temperature of a chemical change was reduced,the reaction rate could most likely be increased by increasing the concentration of the reactants.

Chemical changes are defined as changes which occur when a substance combines with another substance to form a new substance.Alternatively, when a substance breaks down or decomposes to give new substances it is also considered to be a chemical change.

There are several characteristics of chemical changes like change in color, change in state , change in odor and change in composition . During chemical change there is also formation of precipitate an insoluble mass of substance or even evolution of gases.

There are three types of chemical changes:

1) inorganic changes

2)organic changes

3) biochemical changes

During chemical changes atoms are rearranged and changes are accompanied by an energy change as new substances are formed.

Learn more about chemical change,here:

https://brainly.com/question/2591189

#SPJ6

Answer:

its is true because i think its true???

Answer: C

Explanation:

your well wisher