Answer:
The direction of the magnetic field on point P, equidistant from both wires, and having equal magnitude of current flowing through them will be pointed perpendicularly away from the direction of the wires.
Explanation:
Using the right hand grip, the direction of the magnet field on the wire M is counterclockwise, and the direction of the magnetic field on wire N is clockwise. Using this ideas, we can see that the magnetic flux of both field due to the currents of the same magnitude through both wires, acting on a particle P equidistant from both wires will act in a direction perpendicularly away from both wires.
Currents in DC transmission lines can be 100 A or higher. Some people are concerned that the electromagnetic fields from such lines near their homes could pose health dangers.
A. For a line that has current 150 A and a height of 8.0 m above the ground, what magnetic field does the line produce at ground level? Express your answer in teslas.
B. What magnetic field does the line produce at ground level as a percent of earth's magnetic field which is 0.50 G?
C. Is this value of magnetic field cause for worry? Choose your answer below.
i. Yes. Since this field does not differ a lot from the earth's magnetic field, it would be expected to have almost the same effect as the earth's field.
ii. No. Since this field is much lesser than the earth's magnetic field, it would be expected to have less effect than the earth's field.
iii. Yes. Since this field is much greater than the earth's magnetic field, it would be expected to have more effect than the earth's field.
iv. No. Since this field does not differ a lot from the earth's magnetic field, it would be expected to have almost the same effect as the earth's field.
Answer:
Explanation:
magnetic field due to an infinite current carrying conductor
B = k x 2I / r where k = 10⁻⁷ , I is current in conductor and r is distance from wire
putting the given data
B = 10⁻⁷ x 2 x 100 / 8
= 25 x 10⁻⁷ T .
B )
earth's magnetic field = .5 gauss
= .5 x 10⁻⁴ T
= 5 x 10⁻⁵ T
percent required = (25 x 10⁻⁷ / 5 x 10⁻⁵) x 100
= 5 %
C )
ii. No. Since this field is much lesser than the earth's magnetic field, it would be expected to have less effect than the earth's field.
A scuba diver fills her lungs to capacity (6.0 L) when 10.0 m below the surface of the water and begins to ascend to the surface. Assume the density of the water in which she is swimming is 1000 kg/m3 and use g = 10 m/s2A. Assuming the temperature of the air in her lungs is constant, to what volume must her lungs expand when she reaches the surface of the water?B. What effect would the warming of the air in her lungs have on the volume needed when she surfaces?C. Assuming the temperature of the air in her lungs is constant, what effect does her ascent have on the vrms of the air molecules in her lungs?
Answer:
Explanation:
As temperature is constant , we shall apply Boyle's law
P₁V₁ = P₂V₂
P₁ = pressure at depth of 10 m
= P + hdg , h = 10 , d = 10³ , g = 10
P is atmospheric pressure which is 10⁵ Pa
P₁ = 10⁵ + 10 x 10³ x 10
= 2 x 10⁵
applying the formula
2 x 10⁵ x 6 = 10⁵ x v
v = 2 x 6 = 12 L
volume will be doubled at the surface .
B )
warming of air at the surface will increase the volume of air in her lungs so so she will need more lung capacity .
C )
The rms value of a gas depends upon the temperature of the gas . As temperature of the gas is constant , the rms value of the gas particles will remain constant when she goes to the surface .
The lungs will expand 12 L when she reaches the surface of the water, and the warming of the air results in more lung capacity, and [tex]\rm V_{rms}[/tex] the value remains the same.
What is Boyle's law?According to the law, the pressure of the gas is inversely proportional to the volume of the gas. In other words when the pressure of the gas increases the volume of the gas decreases.
We know the pressure at the 10 meters depth:
[tex]\rm P_1 = P+h\times \rho\times g[/tex]
Where P = Atmospheric pressure
h = Depth
ρ =Density of the water
We have: [tex]\rm P = 10^5 \ Pa[/tex], h = 10 meters, and [tex]\rm \rho = 1000 \ kg/m^3[/tex], and [tex]\rm g = 10 \ m/s^2[/tex]
Putting the values in the above equation, we get:
[tex]\rm P_1 = 10^5+ 10\times 1000\times 10[/tex]
[tex]\rm P_1 = 2\times 10^5[/tex]
From the Boyle's law:
[tex]\rm P_1\times V_1 = P_2\times V_2[/tex]
[tex]\rm 2\times10^5\times 6 = 10^5\times V_2[/tex]
[tex]\rm V_2 = 12 \ L[/tex]
We know that as the air at the surface warms, the volume of air in her lungs expands, requiring more lung capacity.
The temperature of the gas is constant and [tex]\rm V_{rms}[/tex] values for gas depend on the temperature of the gas, but here the temperature of the gas is constant thus, the [tex]\rm V_{rms}[/tex] will remains constant.
Thus, the lungs will expand 12 L when she reaches the surface of the water, and the warming of the air results in more lung capacity, and [tex]\rm V_{rms}[/tex] the value remains the same.
Learn more about the Boyle's law here:
https://brainly.com/question/23715689
The temperature difference between the inside and the outside of a house on a cold winter day is 33°F. (a) Express this difference on the Celsius scale. 0.55 Incorrect: Your answer is incorrect. °C (b) Express this difference on the Kelvin scale. 273.7 Incorrect: Your answer is incorrect. K
Answer:
a) 0.56°C
b) 273.56 K
Explanation:
If we want to convert from Fahrenheit scale to Celcius scale we use the formula;
T(°C) = (T(°F) - 32) × 5/9
Where T(°F) = 33°F
Hence;
T(°C) = (33°F - 32) × 5/9
T°C = 0.56°C
b)
T(K) = T°C + 273
T(K) = 0.56 + 273
T(K) = 273.56 K
A car moving east at 45 km/h turns and travels west at 30 km/h. What is the
magnitude and direction of the change in velocity?
mahalle 1.11
Explanation:
Change in Velocity = final velocity - initial velocity
Change in velocity = 30km/h - (- 45km/h )
= 75 km/h due west
What is the minimum thickness of coating which should be placed on a lens in order to minimize reflection of 566 nm light? The index of refraction of the coating material is 1.46 and the index of the glass is 1.71.
Answer:
The thickness is [tex]t = 1.415 *10^{-7 } \ m[/tex]
Explanation:
From the question we are told that
The wavelength is [tex]\lambda = 566 \ nm = 566 *10^{-9} \ m[/tex]
The index of refraction of glass is [tex]n_g = 1.71[/tex]
The index of refraction of the coating is [tex]n= 1.46[/tex]
Generally the condition for destructive interference is
[tex]2 t = (m + \frac{1}{2} ) * \frac{\lambda }{n }[/tex]
Here m is the order of the interference pattern and given from the question that we are considering minimizing reflection m = 0
t = thickness of the coating
substituting values
[tex]2 t = (0 + \frac{1}{2} ) * \frac{ 566 *10^{-9}}{ 1.46 }[/tex]
=> [tex]t = 1.415 *10^{-7 } \ m[/tex]
¿Cómo podrías utilizar el sistema de posicionamiento global para proponer recorridos alternativos para llegar a un lugar específico (centro educativo, supermercado, el hogar, el parque, entre otros)?
Answer:
El sistema de posicionamiento global (conocido mundialmente como GPS) podría utilizarse para proponer recorridos alternativos para llegar a un lugar específico, como un parque, a través de la creación de un recorrido guiado por una aplicación móvil con diferentes rutas de acceso al lugar.
Así, por ejemplo, se crearían diferentes rutas de acceso desde un punto A hasta un punto B, teniendo en cuenta factores como: rapidez, congestión vehicular, pago o no de peajes, posibilidad de acceso a pie y determinados factores extra que influyan en la forma de llegar al lugar. Todo ello plasmado en un mapa interactivo en el cual se señalen las rutas disponibles mediante el marcado del mapa en cuestión.
Monochromatic light falls on two very narrow slits 0.047 mm apart. Successive fringes on a screen 6.60 m away are 8.9 cm apart near the center of the pattern.
Determine the wavelength and frequency of the light.
Answer::
[tex]\lambda = 634 nm[/tex]
[tex]f = 4.73 *10^{14} \ Hz[/tex]
Explanation:
From the question we are told that
The distance of separation is [tex]d = 0.047 \ mm = 0.047 *10^{-3} \ m[/tex]
The distance of the screen is [tex]D = 6.60 \ m[/tex]
The width of the fringe is [tex]y = 8.9 \ cm = 0.089 \ m[/tex]
Generally the width of the width of the fringes is mathematically represented as
[tex]y = \frac{\lambda * D }{d }[/tex]
=> [tex]\lambda = \frac{y * d }{D }[/tex]
=> [tex]\lambda = \frac{ 0.089 * (0.047 *10^{-3}) }{6.60 }[/tex]
=> [tex]\lambda = 634 *10^{-9}[/tex]
=> [tex]\lambda = 634 nm[/tex]
Generally the speed of light is mathematically represented as
[tex]c = f * \lambda[/tex]
=> [tex]f= \frac{ c}{\lambda }[/tex]
=> [tex]f= \frac{ 3.0 *10^{8}}{634 *10^{-9}}[/tex]
=> [tex]f = 4.73 *10^{14} \ Hz[/tex]
A capacitor consists of two parallel conducting plates, each of area 0.4 m2 and separated by a distance of 2.0 cm. Assume there is air between the plates. While connected to a battery the electric field within the plates is 500 N/C. The potential difference between the plates is: ________
a) 5.0 V
b) 10 V
c) 30 V
d) 20 V
Answer:
check photo
Explanation:
A non-ideal battery has a 6.0-V emf and an internal resistance of 0.6 l. Determine the terminal voltage (in volts) when the current drawn from the battery is 1.0 A
A brick is resting on a smooth wooden board that is at a 30° angle. What is one way to overcome the static friction that is holding the brick in place?Please help i will give brainliest!!!! lower the board so it's level with the ground ____ roughen up the texture of the wooden board ___ raise the board to a higher angle ____ press down on the brick in a direction that is perpendicular to the board _____
Answer:
to overcome the out of friction we must increase the angle of the plane
Explanation:
To answer this exercise, let's propose the solution of the problem, write Newton's second law. We define a coordinate system where the x axis is parallel to the plane and the other axis is perpendicular to the plane.
X axis
fr - Wₓ = m a (1)
Y axis
N- [tex]W_{y}[/tex] = 0
N = W_{y}
let's use trigonometry to find the components of the weight
sin θ = Wₓ / W
cos θ = W_{y} / W
Wₓ = W sin θ
W_{y} = W cos θ
the friction force has the formula
fr = μ N
fr = μ Wy
fr = μ mg cos θ
from equation 1
at the point where the force equals the maximum friction force
in this case the block is still still so a = 0
F = fr
F = (μ mg) cos θ
We can see that the quantities in parentheses with constants, so as the angle increases, the applied force must be less.
This is the force that balances the friction force, any force slightly greater than F initiates the movement.
Consequently, to overcome the out of friction we must increase the angle of the plane
the correct answer is to increase the angle of the plane
Describe at least two unique characteristics of the new space telescope.
Answer: Astro 1 will have a 10x larger field of view than the Hubble.
Explanation: The hubble will also be extremely light weight that way it can go further into space and the mission will be able to last a longer amount of time.
In an inertia balance, a body supported against gravity executes simple harmonic oscillations in a horizontal plane under the action of a set of springs. If a 1.00-kg body vibrates at 1.00 Hz, a 2.00-kg body will vibrate at Group of answer choices
Answer;
a 2.00-kg body will vibrate at 0.707Hz
Answer:-7.9
Explanation:
A certain resistor dissipates 0.5 W when connected to a 3 V potential difference. When connected to a 1 V potential difference, this resistor will dissipate:
Answer:
0.056 WExplanation:
[tex]Power = IV[/tex]
From ohms law we know that
[tex]V= IR\\\\I= \frac{V}{R} \\\\Power= \frac{V}{R}*V\\\\Power= \frac{V^2}{R}[/tex]
Given data
P1 = 0.5 Watt
P2 = ?
V1= 3 Volts
V2= 1 Volt
Thus we can solve for the power dissipated as follows
[tex]P1= \frac{V1^2}{R1}\\\\P2= \frac{V2^2}{R2}[/tex]
[tex]\frac{P1}{P2} = \frac{V1^2}{V2^2}\\\\ P2=\frac{ V2^2}{ V1^2} *P1\\\\ P2=\frac{ 1^2}{ 3^2} *0.5= 0.055= 0.056 W[/tex]
The resistor will dissipate 0.056 Watt
A box is sliding down an incline tilted at a 12° angle above horizontal. The box is initially sliding down the incline at a speed of 1.5 m/s. The coefficient of kinetic friction between the box and the incline is 0.34. How far does the box slide down the incline before coming to rest?
Answer:
The box will cover a distance of 0.9199m before coming to rest
Explanation:
We are given;
Angle of tilt; θ = 12°
Speed of sliding down; u = 1.5 m/s
Coefficient of kinetic friction; μ = 0.34
We are told that the box is sliding down an incline tilted at a 12° angle above horizontal.
Thus,
The components of the weight of the block would be;
Fx = mg sinθ = mg sin 12
Fy = mg cosθ = mg cos 12
For, the normal force on the block, it will be counter balanced by the Y component of weight of block and so we have;
Normal force; Fn = mg cos 12
Now formula for the frictional force would be given by;
Ff = μmg cos 12
So, Ff = 0.34mg cos 12
So, the net force along the inclined plane is;
Fnet = Fx - Ff
Fnet = mg sin 12 - 0.34mg cos 12
Where Fnet = mass x acceleration.
Thus;
ma = mg sin 12 - 0.34mg cos 12
m will cancel out to give;
a = g sin 12 - 0.34g cos 12
a = 9.81(0.2079) - 0.34(9.81 × 0.9781)
a = -1.223 m/s²
According to Newton's equation of motion, we have;
(v² - u²) = 2as
s = (v² - u²)/2a
Final velocity is zero. Thus;
s = (0² - 1.5²)/(2 × -1.223)
s = -2.25/-2.446
s = 0.9199 m
Thus, the box will cover 0.9199m before coming to rest
Coherent light that contains two wavelengths, 660 nm (red) and 470 nm (blue), passes through two narrow slits that are separated by 0.310 mm. Their interference pattern is observed on a screen 4.40 m from the slits. What is the disatnce on the screen between the first order bright fringe for each wavelength?
Answer:
0.002699 m or 2.699 mm
Explanation:
y = Fringe distance
d= Distance between slits = 0.310mm
L = Screen distance = 4.40m
λ= Wavelength
Given from question
λ₁= 660 nm = 6.6 x 10^-9 m
λ₂= 470 nm = 4.7 x 10^-9 m
d = 0.340 mm = 3.4 x 10^-3 m
L = 4.40 m
In the case of constructive interference, we use below formula
y/L = mλ/d
For first order wavelength
(y₁/4.40) =(1×660x10⁻⁹)/(0.310*10⁻³)
y₁= (0.310*10⁻³)×(4.40)/(0.310*10⁻³)
y₁=0.00937m
(y2/4.40) =(1×470x10⁻⁹)/(0.310*10⁻³)
y2= =(1×470x10⁻⁹)×(4.40)/(0.310*10⁻³)
y2=0.00667m
distance between the fringes is given by (y₁ -y2)
=0.00937-0.00667=0.002699m
Therefore, distance on the screen between the first-order bright fringes for the two wavelengths is 0.002699 m or 2.699 mm
Scouts at a camp shake the rope bridge they have just crossed and observe the wave crests to be 9.70 m apart. If they shake the bridge twice per second, what is the propagation speed of the waves (in m/s)?
Answer:
The speed of the wave is 19.4 m/s
Explanation:
The wave's crest to crest distance (the wavelength of this rope's wave) λ= 9.70 m
The bridge is shaken twice, meaning that two wavelengths passed a given point on the rope per sec. The frequency of a wave is the amount of that wave that passes a given point in a second.
this means that the frequency f = 2 Hz
The speed of a wave = fλ = 9.70 x 2 = 19.4 m/s
In a certain process a gas ends in its original thermodynamic state. Of the following, which is possible as the net result of the process?
A. It is adiabatic and the gas does 50 J of work.
B. The gas does no work but absorbs so J of energy as heat.
C. The gas does no work but rejects 50 J of energy as heat.
D. The gas rejects 50 J of energy as heat and does 501 of work.
E. The gas absorbs 50 of energy as heat and does 50」ot work.
Answer:
E. The gas absorbs 50 of energy as heat and does 50」ot work
Explanation:
This is following the law of thermodynamics that energy is neither created nor destroyed
In a physics laboratory experiment, a coil with 250 turns enclosing an area of 14 cm2 is rotated in a time interval of 0.030 s from a position where its plane is perpendicular to the earth's magnetic field to a position where its plane is parallel to the field. The earth's magnetic field at the lab location is 5.0×10^−5 T.Required:a. What is the total magnetic flux through the coil before it is rotated? After it is rotated? b. What is the average emf induced in the coil?
Explanation:
Consider a loop of wire, which has an area of [tex]A=14 \mathrm{cm}^{2}[/tex] and [tex]N=250[/tex] turns, it is initially placed perpendicularly in the earth magnetic field. Then it is rotated from this position to a position where its plane is parallel to the field as shown in the following figure in [tex]\Delta t=0.030[/tex] s. Given that the earth's magnetic field at the position of the loop is [tex]B=5.0 \times 10^{-5} \mathrm{T}[/tex], the flux through the loop before it is rotated is,
[tex]\Phi_{B, i} &=B A \cos \left(\phi_{i}\right)=B A \cos \left(0^{\circ}\right[/tex]
[tex]=\left(5.0 \times 10^{-5} \mathrm{T}\right)\left(14 \times 10^{-4} \mathrm{m}^{2}\right)(1)[/tex]
[tex]=7.0 \times 10^{-8} \mathrm{Wb}[/tex]
[tex]\quad\left[\Phi_{B, i}=7.0 \times 10^{-8} \mathrm{Wb}\right[/tex]
after it is rotated, the angle between the area and the magnetic field is [tex]\phi=90^{\circ}[/tex] thus,
[tex]\Phi_{B, f}=B A \cos \left(\phi_{f}\right)=B A \cos \left(90^{\circ}\right)=0[/tex]
[tex]\qquad \Phi_{B, f}=0[/tex]
(b) The average magnitude of the emf induced in the coil equals the change in the flux divided by the time of this change, and multiplied by the number of turns, that is,
[tex]{\left|\mathcal{E}_{\mathrm{av}}\right|=N\left|\frac{\Phi_{B, f}-\Phi_{B, i}}{\Delta t}\right|}{=} & \frac{1.40 \times 10^{-5} \mathrm{Wb}}{0.030 \mathrm{s}}[/tex]
[tex]& 3.6 \times 10^{-4} \mathrm{V}=0.36 \mathrm{mV}[/tex]
[tex]\mathbb{E}=0.36 \mathrm{mV}[/tex]
(a) The initial and final flux through the coil is 1.75 × 10⁻⁵ Wb and 0 Wb
(b) The induced EMF in the coil is 0.583 mV
Flux and induced EMF:Given that the coil has N = 250 turns
and an area of A = 14cm² = 1.4×10⁻³m².
It is rotated for a time period of Δt = 0.030s such that it is parallel with the earth's magnetic field that is B = 5×10⁻⁵T
(a) The flux passing through the coil is given by:
Ф = NBAcosθ
where θ is the angle between area vector and the magnetic field
The area vector is perpendicular to the plane of the coil.
So, initially, θ = 0°, as area vector and earth's magnetic field both are perpendicular to the plane of the coil
So the initial flux is:
Φ = NABcos0° = NAB
Ф = 250×1.4×10⁻³×5×10⁻⁵ Wb
Ф = 1.75 × 10⁻⁵ Wb
Finally, θ = 90°, and since cos90°, the final flux through the coil is 0
(b) The EMF induced is given by:
E = -ΔФ/Δt
E = -(0 - 1.75 × 10⁻⁵)/0.030
E = 0.583 × 10⁻³ V
E = 0.583 mV
Learn more about magnetic flux:
https://brainly.com/question/15359941?referrer=searchResults
A baseball (m=145g) traveling 35 m/s moves a fielder's glove backward 23 cm when the ball is caught. What was the average force exerted by the ball on the glove?
Answer:
386.13 N
Explanation:
The kinetic energy of the baseball is converted into workdone in moving the glove backward( work energy theorem).
Therefore, KE of the ball
[tex]\frac{1}{2} mv^2 =\frac{1}{2}(0.145)35^2\\ = 88.81 \text{J}[/tex]
Now, workdone in moving the glove
W= Fd
where F = Force applied, d = displacement of the glove= 0.23 cm.
88.81 = F×0.23
F= 88.81/0.23 = 386.13 N
A spherical balloon has a radius of 6.95m and is filled with helium. The density of helium is 0.179 kg/m3, and the density of air is 1.29 kg/m3. The skin and structure of the balloon has a mass of 960kg . Neglect the buoyant force on the cargo volume itself. Determine the largest mass of cargo the balloon can lift.
Answer:
602.27 kg
Explanation:
The computation of the largest mass of cargo the balloon can lift is shown below:-
Volume of helium inside the ballon= (4 ÷ 3) × π × r^3
= (4 ÷ 3) × 3.14 × 6.953
= 1406.19 m3
Mass the balloon can carry = volume × (density of air-density of helium)
= 1406.19 × (1.29-0.179)
= 1562.27 kg
Mass of cargo it can carry = Mass it can carry - Mass of structure
= 1562.27 - 960
= 602.27 kg
"In a Young's double-slit experiment, the slit separation is doubled. To maintain the same fringe spacing on the screen, the screen-to-slit distance D must be changed to"
Answer:
To maintain the same fringe spacing on the screen, the screen-to-slit distance D must be changed to a value 2D that is twotimes D
A bucket filled with water has a mass of 23 Kg and is attached to a rope, which in turn is wound around a 0.050 m radius cylinder at the top of a well. What torque does the weight of water and bucket produce on the cylinder if the cylinder is ont permitted to rotate? (g= 9.8 m/s2)
Answer:
The torque is 11.27 N m
Explanation:
Recall that torque is the vector product of the force times the distance to the pivoting point. So in our case, the distance to the pivoting point is the radius of the cylinder (0.05 m), and the force is given by the weight of the bucket full of water (W = 9.8 * 23 N = 225.4 N)
Then the torque is: 0.05 * 225.4 N m = 11.27 N m
two thin lenses with the focal length of magnitude 15.0 cm . the first is diverging and second is converging lens are located 11.3 cm apart. an object 1.60 mm tall is placed 25 cm to the left of the first diverging lens. how far the first lens is the final image is formed?
is the final image is real or virtual?
what is the height of image?
Answer:
grandson annual Iranian Jamal Jamal Hannah travel
Cho hai mặt cầu đồng tâm O tích điện đều. Bán kính của hai mặt cầu lần lượt là R1 và R2 (R2>R1). Điện tích mặt trong là q và mặt ngoài là Q
Tính cường độ điện trường tại một điểm cách tâm O một đoạn r (biết R1 < r < R2)
Tính hiệu điện thế giữa hai mặt cầu
Answer:
you will stc ohxoyxct txxtx xigigjjgjvvixiffjz,iffzikzfjvixii. hi h ohigiogooigoh
Explanation:
k jjvhvojvovvojivivivihvi hj
You are walking around your neighborhood and you see a child on top of a roof of a building kick a soccer ball. The soccer ball is kicked at 31° from the edge of the building with an initial velocity of 15 m/s and lands 63 meters away from the wall. How tall, in meters, is the building that the child is standing on?
Answer:
69.58 m tall
Explanation:
Pls see attached file
What about Iceland's location makes it particularly well-suited to produce electricity from geothermal energy
Answer:
Iceland lies on a boundary where two plates are moving away from each other. Heat from Earth’s interior rises through this plate boundary at a fast rate. This fact makes Iceland well-suited to producing electricity using its abundance of geothermal energy.
Explanation:
Edmentum sample answer.
A motorist traveling with a constant speed of 15 m/s (about 34 mi/h) passes a school-crossing corner, where the speed limit is 0 m/s (about 22 mi/h). Just as the motorist passes, a police officer on a motorcycle stopped at the comer starts off in pursuit with constant acceleration of 3.0 m/S2. (a) How much time elapses before the officer catches up with the motorist? (b) What is the officer's speed at that point? (c) What is the total distance each vehicle has traveled at that point? Please help me
Answer:
(a) 10 s
(b) 30 m/s
(c) 150 m
Explanation:
The motorist's position at time t is:
x = 15t
The officer's position at time t is:
x = ½ (3) t² = 1.5 t²
(a) When they have the same position, the time is:
15t = 1.5 t²
t = 0 or 10 s
(b) The officer's speed is:
v = 3t
v = 30 m/s
(c) The position is:
x = 15t = 150 m
A student uses a spring scale attached to a textbook to compare the static and kinetic friction between the textbook and the top of a lab
table. If the scale measures 1,580 g while the student is pulling the sliding book along the table, which reading on the scale could have been
possible at the moment the student overcame the static friction? (1 point)
1,860 g
820 g
1,580 g
1,140 g
Answer:
1,860 g
Explanation:
In a system, the coefficient of static friction is usually higher than the coefficient of kinetic friction. This means that the kinetic friction is usually less than the static friction. From the question, since the book is already sliding, it means that kinetic friction is the friction in play. This means that before the reading on the scale that could have been possible at the moment the student overcame the static friction must be greater than the reading on the scale during sliding. The only option above 1580 g is 1860 g
Which best identifies the requirements for work to be performed? an object that has a force acting on it an object that is moving and has no net force a force acting on a motionless object a force that moves an object
Answer:
a force that moves an object
Explanation:
the formula for work is force * distance
This question involves the concepts of work, force, and displacement.
The statement that best identifies the requirements for work to be performed is "a force that moves an object".
Work is defined as the product of force applied on an object and the distance moved by the object. Mathematically,
Work = (Force)(Displacement)
Hence, both the applied force and the displacement of the object as a result of the application of the force is necessary for the work to be done. If any one of these values becomes zero, the work automatically becomes zero, which means no work is performed.
Learn more about work here:
https://brainly.com/question/4095205
Which object forms when a supergiant explodes? a red giant a black hole a white dwarf a neutron star
Answer:
a neutron star
Explanation:
Answer:
d
Explanation: