Derive the next state equations for each type (D, T, SR, and JK) of basic memory element. The next state equation is a symbolic equation describing the next state (Q ) as a function of the inputs (D,T,SR, or JK) and state (Q). In order to determine the next state equations for a a JK memory element, build a 3-variable Kmap with Q, J, and K as the inputs. The entries in the Kmap should be Q . Solving this Kmap will yield the next state equation. Show all work for full credit.

Answer:

Explanation:

From the information given:

[tex]E_1 = 68 \ GPa \\ \\ E_2 = 201 \ GPa \\ \\ d = 25 \ mm \ \\ \\ D = 45 \ mm \ \\ \\ L = 761 \ mm \\ \\ P = -88 kN[/tex]

The total load is distributed across both the rod and tube:

[tex]P = P_1+P_2 --- (1)[/tex]

Since this is a composite column; the elongation of both aluminum rod & steel tube is equal.

[tex]\delta_1=\delta_2[/tex]

[tex]\dfrac{P_1L}{A_1E_1}= \dfrac{P_2L}{A_2E_2}[/tex]

[tex]\dfrac{P_1 \times 0.761}{(\dfrac{\pi}{4}\times .0025^2 ) \times 68\times 10^4}= \dfrac{P_2\times 0.761}{(\dfrac{\pi}{4}\times (0.045^2-0.025^2))\times 201 \times 10^9}[/tex]

[tex]P_1(2.27984775\times 10^{-8}) = P_2(3.44326686\times 10^{-9})[/tex]

[tex]P_2 = \dfrac{ (2.27984775\times 10^{-8}) P_1}{(3.44326686\times 10^{-9})}[/tex]

[tex]P_2 = 6.6212 \ P_1[/tex]

Replace [tex]P_2[/tex] into equation (1)

[tex]P= P_1 + 6.6212 \ P_1\\ \\ P= 7.6212\ P_1 \\ \\ -88 = 7.6212 \ P_1 \\ \\ P_1 = \dfrac{-88}{7.6212} \\ \\ P_1 = -11.547 \ kN[/tex]

Finally, to determine the normal stress in aluminum rod:

[tex]\sigma _1 = \dfrac{P_1}{A_1} \\ \\ \sigma _1 = \dfrac{-11.547 \times 10^3}{\dfrac{\pi}{4} \times 25^2}[/tex]

[tex]\sigma_1 = - 23.523 \ MPa}[/tex]

Thus, the normal stress = 23.523 MPa in compression.

Answer:

c   Waste stack

Explanation:

Answer:

Explanation:

The missing part of the question is attached in the diagram below, the second diagram shows the schematic view of the stress-strain curve and the plane stress.

From the given information:

The elastic modulus is:

[tex]E = \dfrac{\sigma}{\varepsilon} \\ \\ E = \dfrac{150 \ MPa}{0.0217} \\ \\ E = 69.124 \ GPa[/tex]

Hence, suppose 0.2% offset cuts the stress-strain curve at a designated point A from the image attached below, then the yield strength relating to the stress axis from the curve will be [tex]\sigma_y[/tex] = 270 MPa.

The shear yield strength by using von Mises criteria is estimated as;

[tex]\tau_1 = \dfrac{\sqrt{2}}{3}\sigma_y \\ \\ \tau_1 = \dfrac{\sqrt{2}}{3}*270 \\ \\ \tau_1 = 127.28 \ MPa[/tex]

The shear yield strength by using Tresca criteria is:

[tex]\tau_2 = \dfrac{1}{2}\sigma_y \\ \\ \tau_2= \dfrac{1}{2}*270 \\ \\ \tau_2 = 135 \ MPa[/tex]

Answer:

The application of regulations in locations are very important.

Explanation:

The application of regulations in locations are very important in order to gain more benefit from it because people choose those places that are well regulated and having more facilities. If the location has baths, showers, electric floor heaters and other necessities so the people prefer the place over another and increase of clients occurs which give more benefits to the place owners.

Where are your answer options?

Answer:

Implement a hazard communication program

Explanation: i took the quiz