Answer:
1) 1000Nm
2) 95,625Nm
3) 1.05%
Explanation:
Mechanical Advantage is the ratio of the load to the effort applied to an object.
MA = Load/Effort
1) Workdone on the load = Force(Load) * distance covered by the load
Workdone on the load = 500N * 2m
Workdone on the load = 1000Nm
2) work done by the effort = Effort * distance moves d by effort
work done by the effort = 2125 * 45
work done by the effort = 95,625Nm
3) Efficiency = Workdone on the load/ work done by the effort * 100
Efficiency = 1000/95625 * 100
Efficiency = 1.05%
Hence the efficiency of the system is 1.05%
Even in the most advanced circuits, we cannot oscillate electrons back and forth at that rate through wires. But we can oscillate charges back and forth quickly enough to broadcast TV using radio wave signals. At what frequency do the electronics at the TV station need to have the charges oscillate back and forth on a TV broadcast antenna to transmit a typical TV signal (say a radio wave transmission signal with a wavelength of 1 meter)
Answer:
the oscillations of the electrons must be in the 10⁸ Hz = 100 MHz range
Explanation:
The speed of a wave of radio, television, light, heat, all are manifestations of electromagnetic waves that are oscillations of electric and magnetic fields that support each other, the speed of all these waves is the same and the vacuum is equal to c = 3 108 m / s
All waves have a relationship between the speed of the wave, its frequency and wavelength
c = λ f
f = c /λ
for this case lam = 1 m
f = 3 10⁸/1
f = 3 10⁸ Hz
the oscillations of the electrons must be in the MHz range
It should be clarified that the speed of light in air is a little lower
n = c / v
v = c / n
the refractive index of vacuum is n = 1 and the refractive index of air is n = 1.000002
An object is accelerated by a net force in which direction?
A. at an angle to the force
B. in the direction of the force
C. in the direction opposite to the force
D. Any of these is possible.
Answer:
B. in the direction of the force
Explanation:
Sana nakatulong
When grip strength increases:
a. action potential voltage increases.
b. action potential frequency decreases.
c. action potential frequency increases.
d. action potential frequency increases.
e. the number of active motor units increases.
Answer:
e. the number of active motor units increases.
Explanation:
There is a direct relationship between the number of active motor units and the grip strength in a given scenario. For example, increase in the grip strength leads to increase in the number of active motor units. In the other-hand, the decrease in grip strength leads to the decrease in the number of active motor units.
Cells use nutrients and oxygen to supply the body with the energy it needs. What three-body systems are working together in this situation?
A
nervous, digestive, and circulatory systems
B
digestive, circulatory, and excretory systems
C
circulatory, immune, and respiratory systems
D
digestive, respiratory, and circulatory systems
Answer:
The respiratory system provides oxygen for cells, while the circulatory system transports oxygen to cells.
Explanation:
so the answer is D
Use the drop-down menus to complete each statement about tornado safety.
Before a tornado warning occurs, you should
✔ have a disaster plan ready.
If you’re indoors during a tornado, you should
✔ go to the basement.
If you’re outdoors during a tornado, you should
✔ lie in a ditch or low-lying area.
Answer:
correct tysmm
Explanation:
Calculate the first and second order angles for light of wavelength 400. nm and 700. nm of the grating contains 1.00 x 104 lines/cm.
Answer:
[tex]23.58^{\circ}[/tex] and [tex]53.13^{\circ}[/tex]
[tex]44.43^{\circ}[/tex], second order does not exist
Explanation:
n = Number of lines grating = [tex]1\times10^4\ \text{Lines/cm}[/tex]
[tex]\lambda[/tex] = Wavelength
m = Order
Distance between slits is given by
[tex]d=\dfrac{1}{n}\\\Rightarrow d=\dfrac{1}{1\times 10^4}\\\Rightarrow d=10^{-6}\ \text{m}[/tex]
[tex]\lambda=400\ \text{nm}[/tex]
m = 1
We have the relation
[tex]d\sin\theta=m\lambda\\\Rightarrow \theta=\sin^{-1}\dfrac{m\lambda}{d}\\\Rightarrow \theta=\sin^{-1}\dfrac{1\times 400\times 10^{-9}}{10^{-6}}\\\Rightarrow \theta=23.58^{\circ}[/tex]
m = 2
[tex]\theta=\sin^{-1}\dfrac{2\times 400\times 10^{-9}}{10^{-6}}\\\Rightarrow \theta=53.13^{\circ}[/tex]
The first and second order angles for light of wavelength 400 nm are [tex]23.58^{\circ}[/tex] and [tex]53.13^{\circ}[/tex].
[tex]\lambda=700\ \text{nm}[/tex]
m = 1
[tex]\theta=\sin^{-1}\dfrac{1\times 700\times 10^{-9}}{10^{-6}}\\\Rightarrow \theta=44.43^{\circ}[/tex]
m = 2
[tex]\theta=\sin^{-1}\dfrac{2\times 700\times 10^{-9}}{10^{-6}}[/tex]
Here [tex]\dfrac{2\times 700\times 10^{-9}}{10^{-6}}=1.4>1[/tex] so there is no second order angle for this case.
The first order angle for light of wavelength 700 nm are [tex]44.43^{\circ}[/tex].
Second order angle does not exist.
Linearly polarized light whose Jones vector is [0 1] (horizontally polarized) is sent through a train of two linear polarizers. The first is oriented with its transmission axis at 45 degrees and the second has its transmission axis vertical. Show that the emerging light is linearly polarized in the vertical direction; that is, the plane of polarization has been rotated by 90 degrees.
Answer:
Following are the solution to the given question:
Explanation:
The input linear polarisation was shown at an angle of [tex]2 \mu[/tex]. It's a very popular use of a half-wave plate. In particular, consider the case [tex]\mu = 45 \pm[/tex], at which the angle of rotation is [tex]90\pm[/tex]. HWP thereby provides a great way to turn, for instance, a linear polarised light that swings horizontally to polarise vertically. Illustration of action on event circularly polarized light of the half-wave platform. Customarily it is the slow axis of HWP that corresponds to either the rotation. Note that perhaps the vector of polarization is "double-headed," i.e., the electromagnetic current swinging back and forward in time. Therefore the turning angle could be referred to as the rapid axis to reach the same result. Please find the attached file.
Solve the below problems being sure to provide the correct significant figures.
1) 1000 ÷ 4.886 = __________
2) 240 ÷ 12.3 = __________
3) 80 x 4.6 = __________
4) 4.527 x 30 = __________
5) 86 x 63.855 x 8000 = __________
6) 700 x 91.186 = __________
7) 7.1 x 348 = __________
8) 50 ÷ 29.1 = __________
9) 98.773 x 24.891 x 409 = __________
10) 0.065 x 3 x 3007 = __________
Answer:
1) 204.6663938
2) 19.51219512
3) 368
4) 135.81
5) 43932240
6) 63830.2
7) 2470.8
8) 1.718213058
9) 1005550.526
10) 586.365
Most of the questions you asked were in repeating decimal form.
Explanation:
How does the REE change as a person ages?
Explain
I go to k12 too and i am writing this test now too. I am like pretty sure my answer is correct. I guess we can kinda help eachother with this assignment cuz i am sorta stuck too.
The older a person gets, the greater REE he has.I dont know i hope this helped a bit I know its not much i need help with this too.
1. When an unbalanced force acts on an object,
O the object remains at rest
the weight of the object decreases.
O the object's motion changes.
the inertia of the object increases.
Which of these is the BEST answer for why science is important?
Science can take us to other planets, even if it’s only through a telescope.
Science is part of human nature; it helps answer questions about how the world works.
Science helps us learn to think more critically and weigh evidence better.
Science gives us better tablet computers and games.
QQQUUUUCCCKKKK!!!!!!
discuss two reasons why people find transition between school and university
Answer:
Is that your answer
A motorcycle is traveling along a highway at 29 m/s. How far does the motorcycle travel in 18 s?
Answer:
the motorcycle travels 522 miles in 18 seconds Explanation: 29 x 18 is 522 I'm pretty sure that's what it was asking but I don't know
(will give brainliest to whoever answers first and explains reasoning) A 10kg object is spun around in a circle with a centripetal acceleration of 3.5m/s^2. What is the centripetal force acting on the object?
Answer:
35 N
Explanation:
F = ma
centripetal force = 10(3.5) = 35 N
A uniform-density 7 kg disk of radius 0.20 m is mounted on a nearly frictionless axle. Initially it is not spinning. A string is wrapped tightly around the disk, and you pull on the string with a constant force of 42 N through a distance of 0.9 m. Now what is the angular speed
Answer:
The angular speed is 23.24 rad/s.
Explanation:
Given;
mass of the disk, m = 7 kg
radius of the disk, r = 0.2 m
applied force, F = 42 N
distance moved by disk, d = 0.9 m
The torque experienced by the disk is calculated as follows;
τ = F x d = I x α
where;
I is the moment of inertia of the disk = ¹/₂mr²
α is the angular acceleration
F x r = ¹/₂mr² x α
The angular acceleration is calculated as;
[tex]\alpha = \frac{2Fr}{mr^2} \\\\\ \alpha = \frac{2F}{mr}\\\\\alpha = \frac{2 \times 42 }{7 \times 0.2} \\\\\alpha = 60 \ rad/s^2[/tex]
The angular speed is determined by applying the following kinematic equation;
[tex]\omega _f^2 = \omega_i ^2 + 2\alpha \theta[/tex]
initial angular speed, ωi = 0
angular distance, θ = d/r = 0.9/0.2 = 4.5 rad
[tex]\omega _f^2 = 2\alpha \theta\\\\\omega _f = \sqrt{2\alpha \theta} \\\\\omega _f = \sqrt{2 \times 60 \times 4.5} \\\\\omega _f = 23.24 \ rad/s[/tex]
Therefore, the angular speed is 23.24 rad/s.
A motorist is driving at 15 m/s when she sees that a traffic light 315m ahead has just turned red. She knows that this light stay red for 25 s, and she wants to be 20 m from the ligt when it turns green again. Taht way, she will still be able to stop if the light stays red longer than expected. She applies the brake gradually such that her acceleration is ax(t)= c + bt, where c and b are constant. Assume she starts with a constant speed at the origin.
Find the values of c a b and any other unknown constants in order to answer the following questions.
1. Given the motorist's acceleration as a function of time, what are her position and velocity fucntions? - Do not use numbers for any constant here. Only derive the position and velocity functions.
2. What is her speed as she reaches the light?
Answer:
1) x = x₀ + vot - ½ c t² - 1/6 bt³, v = v₀ - ct - ½ b t²
2) v₁ = 5.25 m/s, v₂ = -8 m/s
Explanation:
1) For this exercise, the relationship of the body is not constant, so you must use the definition of speed and position to find them.
acceleration is
a = c + bt
a) the relationship between velocity and acceleration
a = [tex]\frac{dv}{dt}[/tex]
dv = -a dt
The negative sign is because the acceleration is contrary to the speed to stop the vehicle.
we integrate
∫ dv = - ∫ a dt
∫ dv = -∫ (c + bt) dt
v = -c t - ½ b t²
This must be valued from the lower limit, the velocity is vo, up to the upper limit, the velocity is v for time t
v - v₀ = -c (t-0) - ½ b (t²-0)
v = v₀ - ct - ½ b t²
b) the velocity of the body is
v = [tex]\frac{dx}{dt}[/tex]
dx = v dt
we replace and integrate
∫ dx = ∫ (v₀ - c t - ½ bt²) dt
x-x₀ = v₀ t - ½ c t² - ½ b ⅓ t³
Evaluations from the lower limit the body is at x₀ for t = 0 and the upper limit the body is x = x for t = t
x - x₀ = v₀ (t-0) - ½ c (t²-0) + [tex]\frac{1}{6}[/tex] (t³ -0)
x = x₀ + vot - ½ c t² - 1/6 bt³
2) The speed when you reach the traffic light
Let's write the data that indicates, the initial velocity is vo = 15 m / s, the initial position is xo = 315m, let's use the initial values to find the constants.
t = 25 s x = 20
we substitute
20 = 315 + 15 25 - ½ c 25² - 1/6 b 25³
0 = 295 + 375 - 312.5 c - 2604.16 b
670 = 312.5 c + 2604.16 b
we simplify
2.144 = c + 8.33 b
Now let's use the equation for velocity,
v = v₀ - ct - ½ b t²
v = 15 - c 25 - ½ b 25²
v = 15 - 25 c - 312.5 b
let's write our two equations
2.144 = c + 8.33 b
v = 15 - 25 c - 312.5 b
Let's examine our equations, we have two equations and three unknowns (b, c, v) for which the system cannot be solved without another equation, in the statement it is not clear, but the most common condition is that if the semaphore does not change, it follows with this acceleration (constant) to a stop
a = c + b 25
from the first equation
c = 8.33 / 2.144 b
C = 3.885 b
we substitute in the other two
v = 15 - 25 (3.885 b) - 312.5 b
v = 15 - 409.6 b
final acelearation
a = 28.885 b
let's use the cinematic equation
[tex]v_{f}^2[/tex]= v² - 2 a x
0 = v² - 2a 20
0 = v² - (28.885b) 40
v² = 1155.4 b
we write the system of equations
v = 15 - 409.6 b
v² = 1155.4 b
resolve
v²= 1155.4 ( [tex]\frac{15 -v }{409.6}[/tex] )
v² = 2.8 ( 15 -v)
v² + 2.8 v - 42.3 = 0
v= [ -2.8 ±[tex]\sqrt {2.8^2 + 4 \ 42.3) }[/tex] ]/2 = [-2.8 ± 13.3]/2
v₁ = 5.25 m/s
v₂ = -8 m/s
On a cold winter day, a steel metal fence post feels colder than a wooden fence post of identical size because: a. The specific heat capacity of steel is higher than the specific heat capacity of wood. b. The specific heat capacity of steel is lower than the specific heat capacity of wood. c. Steel has the ability to resist a temperature change better than wood. d. The mass of steel is less than wood so it loses heat faster. Selected:e. Two of the above statements are true.
Answer:
The specific heat capacity of steel is lower than the specific heat capacity of wood
Explanation:
THERE IS ONLY 1 ON MY assignment i geot dis right please brainlyist
The specific heat capacity of steel is lower than the specific heat of a piece of wood. Therefore, option (2) is correct.
What is the specific heat capacity?Specific heat can be defined as the heat energy required to change the temperature of one unit mass of a substance of a constant volume by 1 °C. The S.I. unit of the specific heat capacity of a material is KJ/Kg.
The thermal capacity of a material is defined as a physical property of a substance. The amount of heat is given to a given mass to create a change in unit temperature.
The mathematical expression of specific heat capacity can be written as :
Q = m C ΔT Where C is the heat capacity.
The specific heat capacity is an intensive property of a substance as it does not depend upon the size of the material.
A steel metal fence post feels colder than a wooden fence post of similar size because the specific heat of steel is lower than the specific heat capacity of wood.
Learn more about specific heat, here:
brainly.com/question/11297584
#SPJ5
A 41.0-kg crate, starting from rest, is pulled across level floor with a constant horizontal force of 135 N. For the first 15.0 m the floor is essentially frictionless, whereas for the next 12.0 m the coefficient of kinetic friction is 0.320. (a) Calculate the work done by all the forces acting on the crate, during the entire 27.0 m path. (b) Calculate the total work done by all the forces. (c) Calculate the final speed of the crate after being pulled these 27.0 m.
Answer:
Explanation:
From the information given;
mass of the crate m = 41 kg
constant horizontal force = 135 N
where;
[tex]s_1 = 15.0 \ m \\ \\ s_2 = 12.0 \ m[/tex]
coefficient of kinetic friction [tex]u_k[/tex] = 0.28
a)
To start with the work done by the applied force [tex](W_f)[/tex]
[tex]W_F = F\times (s_1 +s_2) \times cos(0) \ J[/tex]
[tex]W_F = 135 \times (12 +15) \times cos(0) \ J \\ \\ W_F = (135 \times 37 )J \\ \\ W_F =4995 \ J[/tex]
Work done by friction:
[tex]W_{ff} = -\mu\_k\times m \times g \times s_2 \\ \\ W_{ff} = -0.320 \times 41 \times 9.81 \times 12 \ J \\ \\ W_{ff} = -1544.49 \ J[/tex]
Work done by gravity:
[tex]W_g = mg \times (s_1+s_2) \times cos (90)} \ J \\ \\ W_g = 0 \ j[/tex]
Work done by normal force;
[tex]W_n = N \times (s_1 + s_2) \times cos (90) \ J[/tex]
[tex]W_n = 0 \ J[/tex]
b)
total work by all forces:
[tex]W = F \times (s_1 + s_2) + \mu_k \times m \times g \times s_2 \times 180 \\ \\ W = 135 \times (15+12) \ J - 0.320 \times 41 \times 9.81 \times 12[/tex]
W = 2100.5 J
c) By applying the work-energy theorem;
total work done = ΔK.E
[tex]W = \dfrac{1}{2}\times m \times (v^2 - u^2)[/tex]
[tex]2100.5 = 0.5 \times 41 \times v^2[/tex]
[tex]v^2 = \dfrac{2100.5}{ 0.5 \times 41 }[/tex]
[tex]v^2 = 102.46 \\ \\ v = \sqrt{102.46} \\ \\ \mathbf{v = 10.1 \ m/s}[/tex]
What is diffraction of light
Answer:
According to "http://ww2010.atmos.uiuc.edu" Diffraction is the slight bending of light as it passes around the edge of an object.
Some examples of Light Defraction would be..
-CD reflecting rainbow colours
-Sun appears red during sunset
-From the shadow of an object
A reaction occurs when a compound breaks down. This reaction has one reactant and two or more products. Energy, as from a battery, is usually needed to break the compound apart.
Answer:
decomposition
Explanation:
Two resistors have resistances R1 and R2. When the resistors are connected in series to a 12.6-V battery, the current from the battery is 2.07 A. When the resistors are connected in parallel to the battery, the total current from the battery is 8.98 A. Determine R1 and R2. (Enter your answers from smallest to largest.)
Answer:
When R1 = 2.193, R2 = 3.894
When R1 = 3.894, R2 = 2.193
Explanation:
We are told that when R1 and R2 are connected in series, the voltage is 12.6 V and the current is 2.07 A.
Formula for resistance is;
R = V/I
R = 12.6/2.07
R = 6.087 ohms
Since R1 and R2 are connected in series.
Thus; R1 + R2 = 6.087 ohms
R1 = 6.087 - R2
We are also told that when they are connected in parallel, the current is 8.98 A.
Thus, R = 12/8.98
R = 1.403 ohms
Thus;
(1/R1) + (1/R2) = 1/1.403
Let's put 6.087 - R2 for R1;
(1/(6.087 - R2)) + (1/R2) = 1/1.403
Multiply through by 1.403R2(6.087 - R2) to get;
1.403R2 + 1.403(6.087 - R2) = R2(6.087 - R2)
Expanding gives;
1.403R2 + 8.54 - 1.403R2 = 6.087R2 - (R2)²
(R2)² - 6.087R2 + 8.54 = 0
Using quadratic formula, we have;
R2 = 2.193 ohms or 3.894 ohms
Thus,
R1 = 6.087 - 2.193 or R1 = 6.087 - 3.894
R1 = 3.894 or 2.193
When R1 = 2.193, R2 = 3.894
When R1 = 3.894, R2 = 2.193
PLEASE HELP The United States spends over $20 billion a year on space exploration through NASA. Do you think that this has been worth the cost? In three to five sentences, provide two specific examples of things we have learned from space exploration, and explain how these examples influence your opinion.(4 points)
Answer: I think $20 billion a year it’s worth the cost. The reasoning behind that is because we can conduct research on various things that could help out humanity. Therefore we can conclude that’s spending billions of dollars every year is worth it.
Explanation:
Select the correct answer.
Why are the requirements to become a congressional representative and a senator different?
A.
The framers didn’t want senators to worry about their constituents as often as representatives do.
B.
The framers gave senators more lawmaking powers and responsibilities than representatives.
C.
The framers wanted senators to be more mature and more experienced than representatives.
D.
The framers thought senators and representatives should have reasons to argue with each other.
The framers wanted senators to be more mature and more experienced than representatives. (C)
Answer:
C -> The framers wanted senators to be more mature and more experienced than representatives.
HELP DUE TODAY BEST ANSWER GET BRAINLIE
One of the greatest dangers in a tornado is from flying objects. A 15 pound piece of lumber can turn into a flying missile that could severely damage walls and homes. A piece of steel with a mass of 200 pounds and travelling at the same velocity would cause even more damage. Select any evidence from the list below that you could use to explain why a 200 pound piece of steel would cause more damage than a 15 pound piece of wood travelling at the same velocity.
As the kinetic energy of an object increases, the force it can exert on another object decreases.
As the kinetic energy of an object increases, the force it can exert on another object increases.
Objects with more mass have less kinetic energy.
Objects with more mass have more kinetic energy.
As the velocity of an object increases, its kinetic energy decreases.
As the velocity of an object increases, its kinetic energy increases.
I uploaded the answer to a file hosting. Here's link:
tinyurl.com/wpazsebu
__________ and __________ both heavily relied on dream analysis in their treatment of patients. A. Alfred Adler . . . Albert Ellis B. Alfred Adler . . . Carl Jung C. Sigmund Freud . . . Carl Jung D. Sigmund Freud . . . Alfred Adler
Answer:
C. Sigmund Freud . . . Carl Jung
Explanation:
edge 2021
C.Sigmund Freud and Carl Jung both heavily relied on dream analysis in their treatment of patients.
What is Freud most famous for?Freud is well-known for inventing and developing the approach of psychoanalysis; for articulating the psychoanalytic idea of motivation, intellectual infection, and the structure of the unconscious; and for influencing medical and popular conceptions of human nature by using positing both everyday and strange thought.
Sigmund Freud was an Austrian neurologist who's perhaps maximum known as the founding father of psychoanalysis. Freud advanced a fixed of therapeutic strategies centered on communication therapy that worried the use of techniques that include transference, loose affiliation, and dream interpretation.
Learn more about Sigmund Freud here: https://brainly.com/question/2706543
#SPJ2
help me pls
An object accelerates if it:
a.) changes the direction of its velocity but not the magnitude
b.)changes the magnitude of the velocity but not the direction
c.)changes its speed
d.) all of the above
e.) none of the above
Answer:
D
Explanation:
If you push with a power of 20 Watts
on a 150 Newton object, how long would
it take to push it over the 4.3 m?
Answer:
32.25 s
Explanation:
From the question,
P = W/t.............. Equation 1
Where P = Power, W = work done, t = time.
But
W = F×d................. Equation 2
Where F = force and d = distance
Substitute equation 2 into equation 1
P = F×d/t............... Equation 3
make t the subject of euqation 3
t = (F×d)/P............. Equation 4
Givn: F = 150 N, d = 4.3 m, P = 20 watts.
Substitute these values into equation 4
t = (150×4.3)/20
t = 32.25 s
In a double-slit experiment, light from two monochromatic light sources passes through the same double slit. The light from the first light source has a wavelength of 640 nm. Two different interference patterns are observed. If the 10th order bright fringe from the first light source coincides with the 12th order bright fringe from the second light source, what is the wavelength of the light coming from the second monochromatic light source
Answer:
533.33 nm
Explanation:
Since dsinθ = mλ for each slit, where m = order of slit and λ = wavelength of light. Let m' = 10 th order fringe of the first slit of wavelength of light, λ = 640 nm and m"= 12 th order fringe of the second slight of wavelength of light, λ'.
Since the fringes coincide,
m'λ = m"λ'
λ' = m'λ/m"
= 10 × 640 nm/12
= 6400 nm/12
= 533.33 nm
Which of the following is generally true for people in their old age?
Answer:As people get older, most become better able to regulate negative feelings and emphasize the positive.
Explanation: With age, your skin thins and becomes less elastic and more fragile, and fatty tissue just below the skin decreases. You might notice that you bruise more easily. Decreased production of natural oils might make your skin drier. Wrinkles, age spots and small growths called skin tags are more common.
A hook in boxing primarily involves horizontal flexion of the shoulder while maintaining a constant angle at the elbow. During this punch, the horizontal flexor muscles of the shoulder contract and shorten at an average speed of 75 cm/s. They move through an arc length of 5 cm during the hook, while the fist moves through an arc length of 100 cm. What is the average speed of the fist during the hook
Answer:
average speed of the fist during the hook = 15 m/s or 1500 cm/s
Explanation:
We are given;
Speed of shoulder contraction, v_s = 75 cm/s = 0.75 m/s
Distance moved through the arc length by shoulder, d_s = 5 cm = 0.05 m
Distance moved by the fist, d_f = 100 cm = 1 m
Now, we are to find the average speed of the fist during the hook; v_f
Thus can be gotten from proportion;.
d_f/d_s = v_f/ v_s
Making V_f the subject, we have;
v_f = (d_f × v_s)/d_s
Thus;
v_f = (1 × 0.75)/0.05
v_f = 0.75/0.05
v_f = 15 m/s