consider the loading shown. note: this is a multi-part question. once an answer is submitted, you will be unable to return to this part. identify the equation of the elastic curve for the cantilever beam ab.

Answers

Answer 1

I is the section's second moment of area or moment of inertia. The following techniques can be used to determine the equation for the elastic curve of a beam.

The first and second derivatives of the function that represents the curve in terms of the Cartesian coordinates x and y are dydx and d2ydx2, respectively. Assuming that the longitudinal stresses on the fibers are within the elastic limit, the elastic curve of a beam is the curve formed by the intersection of the neutral surface with the side of the beam. The Bending Moment Equation's double integral is taken in order to perform the fundamental calculation. There are formulas for both cantilever beams and beams that are simply supported.

Learn more about stresses here-

https://brainly.com/question/17252580

#SPJ4


Related Questions

list the 2 material properties and 2 relevant application for following alloying elements in aluminum: a. copper b. silicon c. magnesium d. silicon copper

Answers

The most popular alloying elements for aluminum are copper, zinc, magnesium, silicon, manganese, and lithium. Chromite, titanium, zirconium, lead, and bismuth were added in trace amounts.

Which alloys of aluminum are there?

According to the National Electrical Code, a list of aluminum alloys called AA-8000 is utilized to make wire.

Alclad is a type of aluminum sheet created by gluing extremely pure aluminum to a very strong core material.

Al-Li (lithium, occasionally mercury) (lithium, sometimes mercury)

Alnico (aluminum, nickel, copper) (aluminum, nickel, copper)

Birmabright (aluminum, magnesium) (aluminum, magnesium)

Duralumin (copper, aluminum) (copper, aluminum).

What qualities does aluminum have and what alloying elements are they?

Zinc (Zn) 7xxx - The strongest heat-treatable aluminum alloys are created by combining zinc with aluminum and other elements, typically copper and magnesium. Zinc significantly boosts strength and allows precipitation to harden.

To know more about alloying elements in aluminum visit :-

https://brainly.com/question/14348722

#SPJ4

technician a says that rear gear trains are used on engines because they operate with less noise. technician b says that rear gear trains are used because they have less wear than a front gear train mechanism. who is correct?

Answers

The amount of electrical energy a battery may produce depends on the size, weight, and active area of the plates, claims Technician B.

When a battery is fully charged, it should display 12.6 volts. A value of 12.4 volts, or roughly a charge of 75%, is satisfactory for further testing. Any electrical or electronic device that regulates voltage maintains a power source's voltage within acceptable ranges. The voltage regulator's job is to keep voltages within the range that the electrical equipment using that voltage is capable of withstanding. The hydrogen and oxygen gasses that were present when the battery was first charged are once again created from the water.

Learn more about voltage here-

https://brainly.com/question/16795586

#SPJ4

A system air pressure loss occurs on a trailer resulting in a gradual pressure bleed down. Which of the following will occur FIRST?
a. tractor-protection valve cuts service signal to the trailer
b. tractor-protection valve cuts the trailer supply
c. spring brakes on trailer begin to apply when pressure drops to 60 psi
d. service brakes on trailer apply

Answers

Option D is correct. Safeguards the air brake system in the event that the air suspension system leaks or fails.

A replaceable filter on Premium Valve prevents pollutants and other debris from getting into other air system components. The front or rear brakes won't function properly if one air system has very low pressure. As a result, stopping will take longer for you. Stop the car safely, then get the air brakes system fixed. safeguards the air brake system in the event that the air suspension system leaks or fails. A replaceable filter on Premium Valve prevents pollutants and other debris from getting into other air system components.  

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

technician a says that batteries may slowly fail over time due to the loss of a cell or open circuits within the internal connections. technician b says that batteries may slowly fail over time through the gradual loss of capacity caused by plate deterioration. who is correct?

Answers

According to Technician B, the size, weight, and active area of the plates affect how much electrical energy a battery can generate.

A battery should show 12.6 volts when it is fully charged. For further testing, a measurement of 12.4 volts, which roughly equates to a charge of 75%, is sufficient. Any electrical or electronic device known as a voltage regulator keeps the voltage of a power source within allowable ranges. The voltage regulator is required to maintain voltages within the permitted range that the electrical equipment using that voltage can tolerate. The water is transformed back into the hydrogen and oxygen gasses that it was when the battery was first charged.

Learn more about voltage here-

https://brainly.com/question/16795586

#SPJ4

Suppose a Vestas 112-m wind turbine rated at 3.075 MW is installed at a site having Rayleigh wind statistics with an average wind speed of 8 m/s at the hub height. The cut-out speed VF is 25 m/s.
Estimate the annual electricity generation.
How many hours per year will the turbine be shutdown due to excessive winds

Answers

The annual electricity generation per year, E = 8755.88 MWh/year.

Hours per year that the turbine will be shutdown due to excessive winds,          T = 4.0883 hours/year

What is electricity?

Electricity is a set of physical phenomena related to the presence and movement of matter with an electric charge. Magnetism and electricity are both components of the phenomenon known as electromagnetism, according to Maxwell's equations.

Lightning, static electricity, electric heating, electric discharges, and a variety of other everyday occurrences all involve electricity.

When there is a charge present, whether positive or negative, an electric field is formed. When electric charges move, they generate an electric current, which also produces a magnetic field. When a charge is placed in an electric field that is not zero, it will experience a force.

Learn more about electricity

brainly.com/question/776932

#SPJ4

A spherical gas container made of steel has a 5-m outer diameter
and a wall thickness of 6 mm. Knowing that the internal pressure
is 350 kPa, determine the maximum normal stress and the maximum
shearing stress in the container. show all steps.

Answers

The calculated values are 62.1 Ksi is the maximum normal stress.

Max. Shear stress is 31.05 ksi.

Assuming inner vessel pressure is 60 psi

t=0.375 in, which is the thickness of the vessel's wall

d0/2 -t where r = inner radius

13 x 12 Equals 156 inches, or d0=13 feet in inches.

=78 - 0.375

=77.625 in

The formula for calculating the maximum normal stress in a spherical container is

σ=pr/2t

= 60 x 77.625/ 2 x0.375

100 / 6210 psi = 62.1 Ksi

Shear tension at its maximum, max = max /2

62.1 Ksi/2

=31.05ksi

Learn more about stress here-

https://brainly.com/question/17252580

#SPJ4

discuss the advantages and disadvantages of using advanced ceramics in the structure of internal combustion engines.

Answers

High temperature strength and reduced weight are two benefits of utilizing modern ceramics in internal combustion (I.C.) engine construction.

Why is internal combustion advantageous?

Comparing internal combustion engines to external combustion engines, there are various benefits. Internal combustion engine heat loss is reduced, thermal efficiency is increased, and fuel consumption is decreased since the fuel burns directly in the cylinder.

The drawbacks of combustion are what?

Combustion has a variety of negative environmental effects, some of which include air pollution, noise pollution, oil spills, and gas leaks. Pollution from carbon monoxide is another side effect of incomplete combustion of hydrocarbons.

To know more about internal combustion engines visit:-

https://brainly.com/question/2836941

#SPJ4

technician a says an electronically controlled power steering system provides power assistance when the engine stalls. technician b says an electronic rack eliminates the hydraulic pump and hoses. who is correct?

Answers

The same power steering fluid is reportedly used by all models produced by the same manufacturer, according to technician A.

Which of the aforementioned electric power assist steering systems has the power assist unit?Depending on where the assist motor is located, there are four types of EPS. The direct drive type (D-EPS), the rack assist type, the pinion assist type, and the column assist type (C-EPS) are each of these (R-EPS). The steering column is the hub for the C-EPS type's power assist unit, torque sensor, and controller.When a driver is making a quick turn at a low speed, a power steering pressure switch will send a signal to the powertrain control module telling it to increase the engine speed. The same power steering fluid is reportedly used by all models produced by the same manufacturer, according to technician A.  

To learn more about Power steering refer to:

https://brainly.com/question/28958533?source=archive

#SPJ4

the flip-flop input equations for a bcd counter using t flip-flops are given in section 6.4. obtain the input equations for a bcd counter that uses (a) jk flip-flops and (b)* d flipflops. compare the three designs to determine which one is the most efficient.

Answers

Synchronous is an artistic phrase that denotes that all outputs occur only after a clock, and that the same clock affects all clocked devices. No clock signals should be generated from other circuit components' output.

The term "3-bit" denotes that this circuit has exactly three outputs. The word "binary" denotes that the output bits are meant to represent numbers in a binary system. Although the problem does not state what is being counted, the word "counter" implies that the outputs are supposed to count something. "Up" implies that when events are counted, the number represented by the outputs should grow. What should happen when the count reaches the highest possible count for 3-bits is not specified in the problem.

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

One lbmol of pentane gas (C5H12) reacts with the theoretical amount of air in a closed, rigid tank. Initially, the reactants are at 77°F, 1 atm. After complete combustion, the temperature in the tank is 2500°R. Assume air has a molar analysis of 21% O2 and 79% N2.
Determine the final pressure in the tank, in atm.
Determine the heat transfer in Btu
Please be precise with your calculation.

Answers

After complete combustion, the temperature in the tank is 2500°R. Final pressure in the tank is 0.715 atm and heat transfer is 1900339 BTU.

1lb mol of pentane weighs 102lb. From he chemical equation of combustion,

No of moles of gas initially is 1 mole of pentane + 8 moles of oxygen +30.1 moles of nitrogen=39.1 moles.

No of moles of gas after combustion is 5 moles of carbon dioxide, 6 moles of water and 30.1 moles of nitrogen=41.1 moles.

Assuming all gases are ideal,

Applying ideal gas law to before combustion (1) and after combustion (2),

which is the final pressure in the tank.

Heat transfer to CO2:

5lbmol of CO_2=44*5 lb of CO2 with heat capacity of 0.0138 BTU/lb-deg R

Total heat transferred to CO_2=44*5*0.0138*(2500-536)=5963 BTU

Heat transfer to H_2O.:

We look up at steam table.

6 lb mol of water is produced=18*6 lb of H-2O.

Partial pressure initially is 6/41.1*41.1/39.1 atm=0.153 atm. Temp 536 R

Partial pressure finally is 6/41.1*4.9 atm=0.715 atm. Temp 2500 R

Looking up steam tables, h_f=2120*18*6=228960 BTU

h_i=44.7*18*6=4827 BTU

Net heat transferred=224133 BTU

Heat transfer to N_2

30.1lbmol of N_2=28*30.1 lb of N2 with heat capacity of 0.000249 BTU/lb-deg R

Total heat transferred to N_2=28*30.1*00.000249*(2500-536)=412 BTU

Overall heat content of the gas at 2500R=5963+224133+412=230508 BTU.

The calorific value of pentane is 20890 BTU/lb

So, total heat released=20890*102BTU=2130847 BTU.

So, total heat trasferred out=2130847-230508=1900339 BTU.

Learn more about combustion here:

https://brainly.com/question/12271707


#SPJ4

2. water flows into the 1 m diameter tank at a rate of 0.006 m3/s. it also leaves through a 5 cm diameter orifice at the bottom. at a certain height h, the efflux equals the influx. determine this equilibrium height h. neglect all losses.

Answers

At the bottom, there is a 5 cm diameter orifice through which it also exits. The efflux and influx are equal at height h, and this height is 0.475 m for equilibrium.

inlet at top=0.006 m³/s

hole of outlet = 5 Cm

height = h

for efflux = influx

influx= 0.006 m³/s

efflux=outlet=area*velocity

π/4*0.05²=Area,velocity =[tex]\sqrt 2gh[/tex]

0.006=π/4*0.05*[tex]\sqrt 2gh[/tex]

so  height  h= 0.475m

The term "influx & efflux," which comes from Walt Whitman's "Song of Myself," describes daily movements in which external influences enter bodies, permeate and perplex their organization, and then leave, having changed into something new.

Learn more about efflux here:

https://brainly.com/question/17087482

#SPJ4

a technician is sent out to service a spark type ignition system on a gas furnace. the main burners light, but the spark igniter continues to spark. after 60 seconds, the blower fan comes on and the burner goes out. the technician suspects a faulty:

Answers

The burner extinguishes and the blower fan turns on after 60 seconds. The technician thinks there could be a broken pilot bi-metal.

Next, the main burner flame or the pilot  bi-metal flame are ignited by this igniter. to cool and saturate the flue gases while the furnace is running, the furnace draws air from the surrounding space. However, manufacturers have mostly switched to direct spark ignition or hot surfaces, and this method operates as follows: Thermostat heat request Control board conducts a safety inspection (limit switches, roll out switches). The inducer motor turns on. Powering the ignitor requires turning on the test power cable switch. The ends of the ignitor clip should be checked for sparks. Test the secondary coil below whether a spark appears. Indicator is faulty and has to be changed if spark does not leap the gap or jumps only sometimes.

Learn more about   bi-metal here:

https://brainly.com/question/4023561

#SPJ4

what component (resistor, capacitor, inductor) should the output be taken across for the circuit above in problem 2 to be used as a band-pass filter and what capacitor and inductor values should be chosen from the list below to achieve the center frequency (frequency at which maximum response occurs) of the band-pass filter to be 108 rads/s?

Answers

One can isolate or filter out specific frequencies that fall inside a given band or range of frequencies using a passive band pass filter.

One can isolate or filter out specific frequencies that fall inside a given band or range of frequencies using a passive band pass filter. With just one resistor connected in series with a non-polarized capacitor, the cut-off frequency or "c point" of a straightforward RC passive filter can be precisely controlled, and as we have seen, depending on which way around they are connected, either a Low Pass or a High Pass filter is produced.

These passive filters can be used in straightforward ways in audio amplifier circuits or applications like loudspeaker crossover filters or pre-amplifier tone adjustments. Occasionally, it's required to only transmit frequencies within a specific range that don't start at 0 Hz (DC).

To know more about filter click here:

https://brainly.com/question/8721538

#SPJ4

bananas are to be cooled from 24 to 13 c at a rate of 215 kg/h by a refrigeration system. the power input to the refrigerator is 1.4 kw. determine the rate of cooling, in kj/min and the cop of the refrigerator. the specific heat of a banana above freezing is 3.35 kj/kg c

Answers

The refrigerator receives a 9.8 kW power input. The proportion of electrical power consumption to heat dissipation is known as the Coefficient of Performance (COP).

It is the criterion used to assess the performance of the air conditioning system. It demonstrates the efficiency of heating and cooling systems. The following list of COP features includes:

The compressor power input to refrigeration output ratio is what determines this.

A rising coefficient of performance (COP) indicates that the cooling output will increase proportionately to the input of electricity. The ratio of electrical power consumption to heat dissipation is known as the Coefficient of Performance (COP). Any system's efficiency will improve with higher COP, and vice versa.

Learn more about input here-

https://brainly.com/question/24179864

#SPJ4

explain why gypsum board is an excellent material for providing fire resistance in building assemblies.

Answers

Answer:

Board with glass fibres in the core provides better fire resistance than gypsum board without glass fibres. The fire resistance of wall assemblies with regular (standard) gypsum board increases as the density of the gypsum board increases. Layering the number of gypsum board on each side of the assembly from one to two improves the fire resistance rating. Well constructed and tested gypsum board wall assemblies offer a first line of defense against the spread of fire and lead to a more sustainable building.

a steel tape that is 100.00 ft long when supported only at its ends under a tension of 20 lb is used to measure a line. the temperature is 68 degree f, the pull on the tape is 40 lb, and the line is measured as 469.40 ft. the tape used is 0.33 in wide x 0.02 in thick. if one assumes the modulus of elasticity of steel to be 29,000,000 psi, what is the actual length of the line? group of answer choices 469.36 ft

Answers

The actual length of the line 469.449 ft, if one assumes the modulus of elasticity of steel to be 29,000,000 psi.

What is elasticity of metal?

A metal's elasticity is defined as the rate at which a specific metal sample can change in size and shape in response to a variety of stress and strain forces as well as other externally varying factors. The measured level of ductility of a metal can also be referred to as elasticity.

Due to the increased surface area that is exposed when elongated, metals that are subjected to repeated applications of force to cause elastic expansion are more vulnerable to stress corrosion, cracking, and crevice corrosion.

When a metal deforms elastically, the process is reversible, allowing the metal to revert to its initial shape.

Learn more about elasticity

https://brainly.com/question/14017540

#SPJ4

Which of the following data structures is the common choice to keep track of the edits made to a document so the user can easily undo their last edit? Stack LinkedList HashSet ArrayList

Answers

Data structures is the common choice to keep track of the edits made to a document so the user can easily undo their last edit is stack data

What is meant by stack  data ?

In data stacking, the values for each of the variables are stacked into a single column after a data set is broken up into smaller data files. It is a form of data wrangling that is employed while getting ready data for additional analysis.

The Last-In-First-Out (LIFO) concept is used by stacks in data structures, a linear type of data structure that permits insertion and deletion operations from the top end of the stack data structure.

In a particular part of the computer's memory called a stack, functions' temporary variables are kept. While the programme is running, variables in a stack are created, saved, and initialized. It serves as a short-term memory. The memory of the variable is automatically cleared after the computation is finished.

To learn more about stack data refer to :

https://brainly.com/question/15242038

#SPJ4

technician a says that diesel engine oil turns black faster than oil in a spark-ignition engine because the oil composition and quality are different between the two oils. technician b says that there is not difference between diesel engine and spark-ignition engine oil. who is correct?

Answers

Neither technician a nor technician b is correct because The occurrence of blackened diesel oil is typical. Several hundred miles after an oil change is when this change is typically noticed.

Diesel engines run at compression ratios that are greater than those of gasoline engines. greater ratio compared to gasoline engines. increased thermal expansion as a result. more fuel energy that is transformed into usable power. In general, diesel oil is more viscous and pumpable at lower temperatures than gas engine oil. Several problems, including heat production, early wear & tear, and more, may arise if it were utilized in gas engines. Increased wear in the valve train, rings and liners, and other high-contact regions of the engine may result from adding natural gas engine oil to a diesel engine. Reduced soot control would result in higher oil viscosity. Compared to gas engine oil, diesel engine oil is more viscous and less pumpable at high temperatures. Several problems, including heat production, early wear & tear, and more, may arise if it were employed in gasoline engine.

Learn more about diesel oil here:

https://brainly.com/question/8829745

#SPJ4

slow, continuous movement along a fault zone is termed . a) elastic rebound b) dilatancy c) sick- slip motion d) stress

Answers

Stress is the proper response. Creep is the name given to the sluggish, persistent movement that occurs along particular fault zones.

During an earthquake, the crustal material on either side of a fault experiences elastic rebound. According to the theory, a fault remains stuck until the strain that has built up in the rock on either side of it has defeated the friction that causes it to stick. The elastic rebound theory offers an explanation for how seismic energy is distributed. In response to force and shifting, rocks on opposite sides of a fault build up energy and gradually distort until their internal strength is exceeded.

Learn more about stress here-

https://brainly.com/question/17252580

#SPJ4

a water distribution system inside a building and used for plumbing facilities is typically referred to by what name?

Answers

Answer:

domestic water return

Explanation:

Hope it helps!

synthetic oils used in turbine engines have advantages over petroleum based oils. two of these advantages are

Answers

The two of these advantages of synthetic oils are improved thermal and oxidative stability. More desirable viscosity-temperature characteristics.

What is synthetic oil ?A lubricant called synthetic oil is made of chemical substances that have undergone artificial modification or synthesis. In addition to being made from alternative raw materials, synthetic lubricants can also be produced utilising chemically altered petroleum components rather than full crude oil. However, the majority of the underlying material is still crude oil, which is distilled before being physically and chemically altered. It will differ between producers and is typically a business trade secret how additives are actually made.In situations where operating temperatures are extremely high, synthetic oil is utilised in place of petroleum-refined oils. For instance, synthetic oils are necessary for aircraft jet engines but not for aircraft piston engines. In addition, synthetic oils are utilised in metal stamping to offer advantages over traditional petroleum- and animal-fat-based goods in terms of the environment and other factors.

To learn more about synthetic oil refer :

https://brainly.com/question/18238576

#SPJ4

#include #include #include "Savings.h" #include "Checking.h" using namespace std; pint main() { Checking* checking = new Checking(1); checking->setFirstName ("Alice"); checking->setLastName("Meacham"); checking->setAccountBalance (1000.00); checking->setoverdraftProtection(true); checking->display(); delete checking; Savings* savings = new Savings(2); savings->setFirstName("Bob"); savings->setLastName("Ferling"); savings->setAccountBalance(1003.00); savings->setInterestRate(5.00); savings->display(); return 0; 1 2 3 4 5 HNM COOO #include #include #include #include "Account.h" using namespace std; Account::Account(int accountNumber) { firstName = lastName = ". "; accountBalance = 0; this->account Number = account Number; 6 7 8 9 10 11 12 evoid Account::deposit(double amount){ accountBalance += amount; Ovoid Account::withdraw(double amount){ accountBalance -= amount; 1 W NPO 3a avoid Account::display(){ cout << "Balance: " « setprecision(2) « accountBalance << endl; cout << "Account: " « account Number << endl; cout << "First Name: " « firstName << endl; cout << "Last Name: " « lastName << endl; void Account::setAccount Number(int accountNumber){ this->accountNumber = accountNumber; 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 avoid Account::setAccountBalance (double accountBalance) { this->accountBalance = accountBalance; avoid Account::setFirstName(string firstName) { this->firstName = firstName; avoid Account::setLastName(string lastName) { this->lastName = lastName; string Account::getFirstName() { return firstName; 899 Ostring Account::getLastName(){ return lastName; 与会员专员后台 41 42 43 44 45 46 } pint Account::getAccountNumber(){ return accountNumber; } double Account::getAccountBalance(){ return accountBalance; 2 3 6 9 L1 UE W NOGUE W N OOOO JOU EWNE #ifndef ACCOUNT_H #define ACCOUNT_H #include using namespace std; class Account{ protected: int account Number; double accountBalance; string firstName; string lastName; public: Account(int accountNumber); void deposit(double amount); void withdraw(double amount); void display(); void setAccount Number(int account Number); void setAccountBalance (double accountBalance); void setFirstName(string firstName); void setLastName(string lastName); int getAccountNumber(); double getAccountBalance(); string getFirstName(); string getLastName(); 14 L5 16 L7 18 19 21 22 23 24 25 #endif 1 2 3 4 5 6 7 8 #include #include #include #include "Checking.h" using namespace std; Checking:: Checking(int accountNumber) : Account(accountNumber){ overdraftProtection = false; ноооо зол во мноооо оол EN NE 13 14 avoid Checking::display() { cout << "Balance: " « fixed << setprecision(2) « accountBalance << endl; cout << "Account: " « accountNumber << endl; cout << "First Name: " « firstName << endl; cout << "Last Name: " « lastName << endl; cout < "Overdraft Protection: "« (overdraft Protection ? "true" : "false") << endl << endl; void Checking :: setoverdraftProtection(bool overdraftProtection) { this->overdraftProtection = overdraftProtection; qbool Checking::getoverdraftProtection(){ return overdraft Protection; 21 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 и Ем оноооо ч ол Еw NE #ifndef CHECKING_H #define CHECKING_H #include #include "Account.h" using namespace std; class Checking : public Account{ private: bool overdraftProtection; public: Checking(int account Number); void display(); void setoverdraftProtection(bool overdraftProtection); bool getoverdraftProtection(); | }; #endif 1 2 3 Ц 5 HNMOOOH #include #include #include #include "Savings.h" using namespace std; Savings::Savings(int account Number) : Account(accountNumber) { this->interestRate = 0.0; 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 avoid Savings::display(){ cout << "Balance: " « fixed << setprecision(2) « accountBalance << endl; cout << "Account: " « accountNumber << endl; cout << "First Name: " « firstName << endl; cout << "Last Name: " « lastName << endl; cout << "Interest Rate: " « fixed << setprecision(2) « interestRate << endl << endl; Avoid Savings::setInterestRate(double interestRate) { this->interestRate = interestRate; çdouble Savings::getInterestRate(){ return interestRate; 0 VOU EWNE Q#ifndef SAVINGS_H #define SAVINGS_H #include #include "Account.h" ſusing namespace std; class Savings : public Account{ private: double interestRate; public: Savings(int accountNumber); Savings(); void deposit(double amount); void withdraw(double amount); void display(); void setInterestRate(double interestRate); double getInterestRate(); 10 11 12 13 14 15 16 17 18 #endif

Answers

It is code wiritten for checking the Account Balance and checking the intrest rates of the amount and is saved in file name callled savings.cpp.

A file containing C code has the file extension.c, whereas a file containing C++ code has the file extension cpp. The C++ programming language, also known as "C with Classes," was developed by computer scientist  as an extension of the C programming language.  Widely used as an object-oriented programming language is C++. By giving the C programming language support for objects, Stroustrup created C++. The term "object-oriented programming language" refers to a language that supports object-oriented programming. Due to its statically typed syntax and quicker code compilation, C++ is faster than Python. Python is slower than C++ because it uses the interpreter and supports dynamic typing, which slows down compilation.

Learn More about programming language here:

https://brainly.com/question/23959041

#SPJ4

which combination of n-type (n) and p-type (p) semiconductors would be used to amplify a weak electronic signal?

Answers

To boost a weak electronic signal, n-type (n) and p-type (p) semiconductors would be utilized in an n-p-n configuration.

How are p-type and n-type semiconductors combined?

Electrons flow from the N-type zone to the P-type region when voltage is supplied by connecting the P-type to the "+" electrode and the N-type to the "-" electrode. Any remaining electrons that did not vanish due to recombination with holes travel to the "+" electrode, and current flows. The P-type region's holes are subject to the same procedure.

Which p- and n-type substances are mixed to create a diode*?

A two-layer, two-terminal semiconductor device, the diode. A PN junction, also known as a diode, is created when n- and p-type semiconductor material are combined.

To know more about semiconductors visit:-

https://brainly.com/question/15184439

#SPJ4

4. question 4 a data analyst is creating a dashboard using tableau. in order to layer objects over other items, which layout should they choose? 1 point floating itemized layered tiled

Answers

A data analyst is creating a dashboard using tableau. in order to layer objects over other items, they should choose floating layout. Thus, the correct option is option A.

Who is a data analyst?

A data analyst examines data to find key customer insights and potential uses for the information. They also share this information with the company's management and other interested parties.

Modern businesses rely heavily on data analysts to reflect on their work and customer base, determine how these factors have affected profits, and advise leadership on how to move forward and expand the company.

McKenzie claims that successful data analysts possess strong mathematical and statistical abilities as well as:

Analytical abilities to collect, view, and evaluate information.Arithmetical abilities to measure and statistically analyze dataTechnical abilities to organize and present data using software and scripting languages.

Learn more about data analysts

https://brainly.com/question/29655960

#SPJ4

Generalized shortest-paths problem. In Internet routing, there are delays on lines but also, more signicantly, delays at routers. This motivates a generalized shortest-paths problem. Suppose that in addition to having edge lengths fle : e 2 Eg, a graph also has vertex costs fcv : v 2 V g. Now dene the cost of a path to be the sum of its edge lengths, plus the costs of all vertices on the path (including the endpoints). Give an efcient algorithm for the following problem. Input: A directed graph G = (V;E); positive edge lengths le and positive vertex costs cv; a starting vertex s 2 V . Output: An array cost[] such that for every vertex u, cost[u] is the least cost of any path from s to u (i.e., the cost of the cheapest path), under the denition above. Notice that cost[s] = cs.

Answers

Algorithm:

1. Initialize cost[u] = ∞ for all u in V.

2. Set cost[s] = cs.

3. For each vertex v in V:

  a. Set dist[v] = 0.

  b. For each edge (u, v) in E:

     i. Set dist[v] = min(dist[v], cost[u] + le).

  c. Set cost[v] = min(cost[v], dist[v] + cv).

4. Return cost[].

Time complexity: O(VE)

What is time complexity?

The duration of the input determines how long it takes an algorithm to run, which is known as temporal complexity. It calculates how long it takes for each algorithm's code statement to run. It won't look at an algorithm's overall execution time. Instead, it is going to supply information about the variance (up or down) in execution time whenever the number of tests (significantly reduce) in an algorithms.

To know more about time complexity
https://brainly.com/question/18041135
#SPJ4

a is a tool used to study the gravitational attraction between earth and a mass within the instrument.

Answers

A gravity meter is a tool used to study the gravitational attraction between the earth and a mass within the instrument.

A gravity meter also known as a gravimeter is a device or instrument that measures local acceleration due to the Earth's gravity and is used to determine the gravitational attraction between the Earth and a mass. A gravity meter works on the principle of measuring the constant downward acceleration of gravity.

Despite the fact that the acceleration of gravity is a vector quantity (that is, it has a magnitude and a direction), most of the gravity meters measure the scalar magnitude of the acceleration.

Gravity meters are of two categories. The first type, the relative gravity meter, measures the difference in gravity between two locations, and the second type is the absolute gravity meter which measures the magnitude of the entire gravity field.

To learn more about gravitational attraction; click here:

https://brainly.com/question/17389873

#SPJ4

technician a says the problem with new long-life anti-freeze is it can produce silicate drop-out, which plugs cooling system passages. technician b says that the problem with long life anti-freeze is that it is not compatible with all cooling system materials. who is correct?

Answers

Silicates, a compound salt containing silicon and oxygen molecules, act as resistors within the fluid to raise the boiling point and reduce the freezing point. They are present in this bright green, fluorescent liquid.

The silicate in the coolant is that white gunk. This is known as silicate dropout, and it occurs when the additives in antifreeze/coolant start to degrade after being used over their recommended lifespan. A system blockage would have resulted from this goo, and the silicate is a component of the corrosion inhibitor kit. Core plugs, also known as freeze plugs, frequently leak as a result of corrosion. The coolant can contact the metal surface of the freeze plug's back. Corrosion prevention is a feature of coolant or antifreeze.

Learn more about resistors here-

https://brainly.com/question/14301731

#SPJ4

7.26 an ic inverter fabricated in a 65-nm cmos process is found to have a load capacitance of 3 ff. if the inverter is operated from a 1.2-v power supply, find the energy needed to charge and discharge the load capacitance. if the ic chip has 5 million of these inverters operating at an average switching frequency of 2.5 ghz, what is the power dissipated in the chip? what is the average current drawn from the power supply?

Answers

In order to charge and discharge the load capacitance, 1.2V x 3F x 2 = 7.2 Joules of energy are required.

The chip can dissipate 7.2 Joules × 5,000,000 x 2.5 GHz, which is 90,000,000 Joules/s, or 90 MW.

The power supply is being used at an average current of 90 MW / 1.2V = 75 A.

What is energy?

Energy is the quantifiable attribute that is transmitted to a body or a physical system in physics. It is observable in the production of work as well as in the form of light and heat. Energy can be transformed in form but cannot be created or destroyed, according to the rule of conservation of energy.

To know more about energy
https://brainly.com/question/13881533
#SPJ4

consider a simple ideal rankine cycle with fixed boiler and condenser pressures. what is the effect of superheating the steam to a higher temperature on

Answers

The net work output and cycle efficiency will both increase with superheating the steam. Additionally, the steam at the turbine exit has less moisture in it.

The superheating raises the mean temperature of heat addition, which raises the efficiency of the superheat Rankine cycle over that of the simple Rankine cycle. On the T-s diagram to the left, the impact of decreasing condenser pressure on the Rankine cycle efficiency is depicted. Steam leaves the condenser as a saturated mixture at the saturation temperature corresponding to the condenser pressure. Rankine cycle in thermodynamics Roy Mech's phrase "Superheated" This cycle demonstrates the different phases of operation in a turbine plant using superheated steam. F -> G is a symbol for the turbine's enthalpy reduction. The effect of superheated steam on the Rankine cycle's efficiency is that the efficiency of the cycle rises as the superheat of the steam rises.

Learn more about superheating here:

https://brainly.com/question/14718830

#SPJ4

if you accidentally write a program that has an infinite (never ending) loop, such as the one below, your computer will become completely unusable sin

Answers

Answer:

yes

Explanation:

Other Questions
how did the actions of slaves themselves, northern military strategy and the emancipation proclamation combine to end slavery? Write as many figure names as possible for the book cover which statement is false? a) a carrot is an example of a taproot. b) white potatoes are modified plant roots. c) stalks of celery are the petioles of the plant. d) the layers of an onion are actually modified leaves. If the electron were replaced with a proton moving with the same velocity, how would the resulting acceleration of the particle change?. write a program that keeps names and email addresses in a dictionary as key-value pairs. the program should display a menu that lets the user look up a persons email address, add a new name and email address, change an existing email address, and delete an existing name and email address. the program should save the data stored in a dictionary to a file when the user exits the program. each time the program starts, it should retrieve the data from the file and store it in a dictionary. the program should include the following functions: a. a function to display a menu. b. a function to look up a persons email address. c. a function to add a new name and email address. d. a function to change an email address. e. a function to delete a name and email address. f. a function to load emails from a file. g. a function to save emails in a file. h. write main function with a loop that displays the menu allowing the user to select an operation from the menu; the program continue until the user enter 5. i. validate all user input. your program should check user input; for example, if the user wants to search or delete a name that does not exist in the dictionary, you should print something like the name is not in the database. if the user selects invalid operation from the menu, the program prints an error and allows the user to renter a valid operation; the program continue asking for a valid operation until a user selects a valid operation. what was the name of the wider, philosophical movement in germany with which albert renger-patzsch is associated? a newsletter publisher believes that more than 52% of their readers own a personal computer. is there sufficient evidence at the 0.02 level to substantiate the publisher's claim? state the null and alternative hypotheses for the above scenario. when assessing a person who is grieving using the grief cycle model, which concept would be most important for the nurse to keep in mind? select all that apply. how many pounds does a 1.98 liter bottle of water weigh on earth? (ignore the weight of the empty plastic bottle, and assume 3 significant digits). an obstetrics nurse is counseling an expectant mother. the mother is concerned about letting people hold her baby once the baby is born, fearing that the infant will get sick. what should the nurse explain to the mother? two blocks are stacked on top of each other on the floor of an elevator as shown. the mass of block 2 (bottom) is 3.0 kg and the mass of block 1 (upper) is 2.0 kg. the elevator is accelerating upwards at a constant rate of 1.6 m/s2. What is the equation of a line perpendicular to 3x+ 4y =12and passes thru the point (3,2)? Write the equation in slope-intercept form (y=mx+b) A powerful communication tool used to clarify documentation in a health record and achieve accurate code assignment is called a. a back brace is prescribed for a client who had a laminectomy. which information would the nurse include in the client's teaching plan? Briefly explain how one specific historical development between 1865 and 1920 was a response to the change in industrial work. consider a function z(x, y) and its partial derivative (z/y)x. can this partial derivative still be a function of x? Which of the following would cause the aggregate demand curve to shift to the left?Group of answer choicesConsumers and firms become more optimistic about the futureAn increase in investmentAn increase in taxesAn increase in government purchases griffith's experiments with s. pneumoniae were significant because they showed that traits could be transferred from one organism to another. what else did he find that was significant? griffith's experiments with s. pneumoniae were significant because they showed that traits could be transferred from one organism to another. what else did he find that was significant? a virus made the bacteria pathogenic protein could not be the genetic material dna was the genetic material heat kills bacteria the transferred traits were heritable Can someone help me the nurse on the oncology unit is planning care for four patients. the patient taking which cytotoxic anticancer drug will require ondansetron least frequently?