One-piece flow is a lean manufacturing technique that produces a single product one at a time, rather than in batches. This approach is beneficial since it reduces waste by producing only what is required, thus improving quality and reducing lead times. This method can be used in simulations to simulate the one-piece flow model that is used in real-life manufacturing.
The main difference between Flexsim and Anylogic is that Flexsim is a 3D modeling tool designed for discrete event simulation, while Anylogic is a general-purpose simulation tool that includes discrete event simulation, system dynamics, and agent-based modeling.
Flexsim is a flexible and powerful 3D simulation tool that is designed specifically for discrete event simulation. It's a complete package that includes tools for modeling, analysis, and visualization of complex systems. Flexsim is designed to be user-friendly, with an intuitive interface that makes it easy to model complex systems quickl
Anylogic is a powerful and flexible simulation tool that can be used for discrete event simulation, system dynamics, and agent-based modeling. Anylogic is a multi-paradigm simulation tool that allows you to model complex systems with ease. It includes a variety of modeling tools, such as discrete event simulation, agent-based modeling, and system dynamics modeling.
To know more about manufacturing visit:
brainly.com/question/33281788
#SPJ11
Q1) Search about Design and Fabrication for compressor in Ac of car supported with photographs
The compressor is a vital component of the car's air conditioning system. It is responsible for compressing the refrigerant gas, which then flows through the condenser and evaporator, cooling the air inside the car. The compressor is typically driven by the engine, but it can also be powered by an electric motor.
The compressor is a complex machine, and its design and fabrication requires a high level of engineering expertise. The compressor must be able to operate at high pressures and temperatures, and it must be durable enough to withstand the rigors of everyday use. The compressor is also required to be energy-efficient, as this can save the car owner money on fuel costs.
The compressor is typically made of cast iron or aluminum, and it is fitted with a number of moving parts, including a piston, a crankshaft, and a flywheel. The compressor is lubricated with oil, which helps to reduce friction and wear. The compressor is also equipped with a number of sensors, which monitor its performance and alert the driver if there is a problem.
The compressor is a critical component of the car's air conditioning system, and its design and fabrication are essential to ensuring that the system operates efficiently and effectively.
To learn more about compressor click here : brainly.com/question/30079848
#SPJ11
A reciprocating compressor draws in 500 ft³/min. of air whose density is 0.079 lb/ft³ and discharges it with a density of 0.304 lb/ft³. At the suction, p1 = 15 psia; at discharge, p2 = 80 psia. The increase in the specific internal energy is 33.8 Btu/lb, and the heat transferred from the air by cooling is 13 Btu/lb. Determine the horsepower (hp) required to compress (or do work "on") the air. Neglect change in kinetic energy.
The horsepower required to compress the air is 156.32 hp.
Given, Volumetric flow rate, Q = 500 ft³/minDensity of air at suction,
ρ1 = 0.079 lb/ft³Density of air at discharge,
ρ2 = 0.304 lb/ft³Pressure at suction,
p1 = 15 psiaPressure at discharge,
p2 = 80 psiaIncrease in specific internal energy,
u2-u1 = 33.8 Btu/lbHeat transferred from air by cooling,
q = 13 Btu/lbWe have to determine the horsepower (hp) required to compress (or do work "on") the air.
Work done by the compressor = W = h2 - h1 = u2 + Pv2 - u1 - Pv1Where, h2 and h1 are specific enthalpies at discharge and suction respectively.
Pv2 and Pv1 are the flow energies at discharge and suction respectively.
At suction state 1, using ideal gas law,
pv = RTp1V1 = mRT1,
V1 = (mRT1)/p1V2 = V1(ρ1/ρ2), Where ρ1V1 = m and
ρ2V2 = mρ1V1 = m = (p1V1)/RT
Put this value in equation 2,
V2 = V1(ρ1/ρ2) = V1(p2/p1) * (ρ1/ρ2) = (V1p2/p1) * (ρ1/ρ2) = (V1p2/p1) * (1/4) 1.
Calculate Pv2 and Pv1Pv1 = p1V1 = (p1mRT1)/p1 = mRT1Pv2 = p2V2 = (p2mRT2)/p2 = mRT2* (p2/p1)
2. Determine h1 and h2.Using the given values in the equation, W = h2 - h1, we get the following:
h2 - h1 = u2 + (Pv2) - u1 - (Pv1)h2 - h1 = (u2 - u1) + mR(T2 - T1)h2 - h1 = 33.8 + mR(T2 - T1)
We have all the values to solve for h1 and h2.
Thus, substituting all the values we get the following:
h2 - h1 = 33.8 + mR(T2 - T1)h2 - h1 = 33.8 + ((p1V1)/R) (T2 - T1)h2 - h1 = 33.8 + (p1V1/28.11) (T2 - T1)h2 - h1 = 33.8 + (15*500)/28.11 (80 - 460)h2 - h1 = 1382.25* Work done by the compressor,
W = h2 - h1 = 1382.25 Btu/lbm * (m) * (1 lbm/60s) = 23.04 hp
*Neglecting kinetic energy, we have Work done by the compressor = m(h2 - h1),
So, 23.04 = m(1382.25 - h1), h1 = 1182.21 Btu/lbm
Power, P = W/t = (23.04 hp * 550 ft.lb/s/hp) / (60 s/min) = 210.19 ft.lb/s
Dividing this by 33,000 ft.lb/min/hp, we get:P = 210.19 / 33,000 hp = 0.00636 hp156.32 hp are required to compress the air.
Answer: 156.32 hp
To learn more about Density
https://brainly.com/question/29775886
#SPJ11
roblem 6 Using a clear sketch show the heat affected zone of a weld. What is its significance? Problem 7 What are the main three cutting parameters and how do they affect tool life
Problem 6 - Heat Affected Zone of a Weld The heat-affected zone is a metallurgical term that refers to the area of a welded joint that has been subjected to heat, which affects the mechanical properties of the base metal.
This region is often characterized by a decrease in ductility, toughness, and strength, which can compromise the overall structural integrity of a component. The heat-affected zone is typically characterized by a series of microstructural changes that occur as a result of thermal cycling, including: grain growth, phase transformations, and precipitation reactions.
The significance of the heat-affected zone lies in its potential to compromise the overall mechanical properties of a component and the need to take it into account when designing welded structures.
Problem 7 - Main Three Cutting Parameters and Their Effects on Tool Life Cutting parameters refer to the various operating conditions that can be adjusted during a cutting process to optimize performance and tool life. The main three cutting parameters are speed, feed, and depth of cut.
Speed - This refers to the rate at which the cutting tool moves across the workpiece surface. Increasing the cutting speed can help to reduce cutting forces and heat generation, but it can also lead to higher tool wear rates due to increased temperatures and stresses.
Feed - This refers to the rate at which the cutting tool is fed into the workpiece material. Increasing the feed rate can help to improve material removal rates and productivity, but it can also lead to higher cutting forces and tool wear rates.
Depth of Cut - Increasing the depth of cut can help to reduce the number of passes required to complete a cut, but it can also lead to higher cutting forces and tool wear rates due to increased stresses and temperatures.
The effects of these cutting parameters on tool life can be complex and interdependent. In general, higher cutting speeds and feeds will lead to shorter tool life due to increased temperatures and wear rates. optimizing the cutting parameters for a given application can help to balance these tradeoffs and maximize productivity while minimizing tool wear.
To know more about metallurgical visit:-
https://brainly.com/question/32005998
#SPJ11
a. What is the essential difference between incomplete location and insufficient location?
b. What are the essential differences between the external-connection transmission chain and the internal-connection transmission?
c. What aspects do the geometric errors of machine tool include?
Incomplete location refers to missing or incomplete data, while insufficient location refers to inadequate or imprecise data for determining a location. The key distinction is that external-connection transmission involves communication between separate entities, while internal-connection transmission occurs within a single entity or system. Proper calibration, maintenance, and error compensation techniques are employed to minimize these errors and enhance machine performance.
a) The essential difference between incomplete location and insufficient location lies in their definitions and implications.
Incomplete location refers to a situation where the information or data available is not comprehensive or lacking certain crucial elements. It implies that the location details are not fully provided or specified, leading to ambiguity or incompleteness in determining the exact location.
Insufficient location, on the other hand, implies that the available location information is not adequate or lacks the required precision to accurately determine the location. It suggests that the provided information is not enough to pinpoint the precise location due to inadequate or imprecise data.
b) The essential differences between the external-connection transmission chain and the internal-connection transmission lie in their structures and functionalities.
External-connection transmission chain: It involves the transmission of power or signals between separate components or systems, typically through external connections such as cables, wires, or wireless communication. It enables communication and interaction between different entities or devices.
Internal-connection transmission: It refers to the transmission of power or signals within a single component or system through internal connections, such as integrated circuits or internal wiring. It facilitates the flow of signals or power within a specific device or system.
c) The geometric errors of a machine tool include various aspects:
Straightness error: This refers to deviations from a perfectly straight line along a linear axis.Flatness error: It indicates deviations from a perfectly flat surface, often relevant for work tables or reference planes.Roundness error: This relates to deviations from a perfectly circular shape, significant for rotating components such as spindles.Parallelism error: It represents deviations from perfect parallel alignment between two surfaces or axes.Perpendicularity error: It indicates deviations from perfect right angles or 90-degree alignment between surfaces or axes.Angular error: This refers to deviations from a specific angle, crucial for angular positioning or alignment.Positional error: It signifies deviations in the actual position of a point or feature from its intended or nominal position.Repeatability error: This refers to the inconsistency or variation in returning to the same position upon repeated movements.LEARN MORE ABOUT calibration here: brainly.com/question/31324195
#SPJ11
MCQ: Which one of the following statements is true about a dual-voltage capacitor-start motor?
A. The auxiliary-winding circuit operates at 115 volts on 115-volt and 230-volt circuits.
B. The main windings are identical to obtain the same starting torques on 115-volt and 230-volt circuits.
C. The direction of rotation is reversed by interchanging the leads of one main winding.
D. The main windings are connected in series for 115-volt operation.
2. An auxiliary phase winding is used in a single-phase fractional horsepower motor to
A. decrease flux density. B. decrease motor heating. C. reverse motor rotation. D. increase motor speed.
3. The device which responds to the heat developed within the motor is the
A. shading coil. B. short-circuiter. C. bimetallic protector. D. current-operated relay.
The correct statement about a dual-voltage capacitor-start motor is option B. The main windings are identical to obtain the same starting torques on 115-volt and 230-volt circuits.
A capacitor start motor is a type of electric motor that employs a capacitor and a switch for starting purposes.
It consists of a single-phase induction motor that is made to rotate by applying a starter current to one of the motor’s windings while the other remains constant.
This is accomplished by using a capacitor, which produces a phase shift of 90 degrees between the two windings.
2. The answer to the second question is option C. Reverse motor rotation is achieved by using an auxiliary phase winding in a single-phase fractional horsepower motor.
In order to start the motor, this auxiliary winding is used. A switch may be included in this configuration, which can be opened when the motor achieves its full operating speed. This winding will keep the motor running in the right direction.
3. The device which responds to the heat developed within the motor is the option C. A bimetallic protector responds to the heat produced inside the motor.
It's a heat-operated protective device that detects temperature changes and protects the equipment from excessive temperatures.
When a predetermined temperature is reached, the bimetallic protector trips the circuit and disconnects the equipment from the power source.
To know more about capacitor visit:
https://brainly.com/question/31627158
#SPJ11
The following information was provided by the responsible engineer of that power plant regarding the steam cycle part: mi, tonnes per hour of superheated steam enters the high-pressure turbine at T₁ °C and P, Bar, and is discharged isentropically until the pressure reaches P₂ Bar. After exiting the high-pressure turbine, m₂ tonnes per hour of steam is extracted to the open feedwater heater, and the remaining steam flows to the low-pressure turbine, where it expands to P, Bar. At the condenser, the steam is totally condensed. The temperature at the condenser's outflow is the same as the saturation temperature at the same pressure. The liquid is compressed to P₂ Bar after passing through the condenser and then allowed to flow through the mixing preheater (a heat exchanger with efficiency n)where it is completely condensed. The preheated feed water will be fed into the heat exchanger through a second feed pump, where it will be heated and superheated to a temperature of T₁°C. In the winter, the overall process heating demand is assumed to be Q MW while this power plant's electricity demand is # MW. 5. Schematic of the power plant: An excellent and high-quality schematic must be presented, with all necessary and appropriate information pertinent to the analysis' content. Any diagramming and vector graphics application, such as Microsoft Visio, can be used. (Maximum 1 page).
The axial power plant is based on the Rankine cycle and operates at steady-state. A schematic diagram of a steam cycle power plant has been provided.
Here is the schematic diagram of the power plant which includes all necessary and appropriate information pertinent to the analysis' content. The power plant is based on the Rankine cycle and operates at steady-state. A schematic diagram of a steam cycle power plant has been provided. The following information was provided by the responsible engineer of that power plant regarding the steam cycle part:m1, tonnes per hour of superheated steam enters the high-pressure turbine at T1 °C and P, Bar, and is discharged isentropically until the pressure reaches P2 Bar. After exiting the high-pressure turbine, m2 tonnes per hour of steam is extracted to the open feedwater heater, and the remaining steam flows to the low-pressure turbine, where it expands to P, Bar.
At the condenser, the steam is totally condensed. The temperature at the condenser's outflow is the same as the saturation temperature at the same pressure. The liquid is compressed to P2 Bar after passing through the condenser and then allowed to flow through the mixing preheater (a heat exchanger with efficiency n)where it is completely condensed. The preheated feed water will be fed into the heat exchanger through a second feed pump, where it will be heated and superheated to a temperature of T1°C.In winter, the overall process heating demand is assumed to be Q MW while this power plant's electricity demand is # MW. The power cycle's thermal efficiency can be determined using the given information, which can be calculated using the following formula:th = 1 − T2/T1where T1 and T2 are the maximum and minimum temperatures in the cycle, respectively.
To know more about axial visit
https://brainly.com/question/33140251
#SPJ11
A ladder and a person weigh 15 kg and 80 kg respectively, as shown in Figure Q1. The centre of mass of the 36 m ladder is at its midpoint. The angle a = 30° Assume that the wall exerts a negligible friction force on the ladder. Take gravitational acceleration as 9.81m/s? a) Draw a free body diagram for the ladder when the person's weight acts at a distance x = 12 m Show all directly applied and reaction forces.
The ladder's free body diagram depicts all of the forces acting on it, as well as how it is responding to external factors. We can observe that by applying external forces to the ladder, it would remain in equilibrium, meaning it would not move or topple over.
Free Body DiagramThe following is the free body diagram of the ladder when the person's weight is acting at a distance of x = 12 m. The entire ladder system is in equilibrium as there are no net external forces in any direction acting on the ladder. Consequently, the system's center of gravity remains at rest.Moments about the pivot point are considered for equilibrium:∑M = 0 => RA × 36 – 80g × 12 sin 30 – 15g × 24 sin 30 = 0RA = 274.16 NAll other forces can be calculated using RA.
To know more about forces visit:
brainly.com/question/13191643
#SPJ11
The turning moment diagram for an engine is drawn to the following scales: Turning moment 1mm = 60 Nm: crank angle, Imm= 10, shows the maximum energy that needs to be stored by the flywheel in unit area is 2850 m2. The flywheel rotates at an average speed of 220 rpm with a total speed change of 2.5%. If the mass of the flywheel is 500 kg, find the appropriate dimensions (inner diameter, outer diameter and thickness) of the flywheel. Given the inner diameter of the flywheel is 0.9 outer diameter and the density is 7.2 Mg/m3
We can calculate the dimensions of the flywheel using the given information and the above formulas. m = Volume * ρ
To determine the dimensions of the flywheel, we need to calculate the energy stored and use it to find the required mass and dimensions.
Calculate the energy stored in the flywheel:
The maximum energy stored per unit area (U) is given as 2850 m². Since the total energy stored (E) is directly proportional to the volume of the flywheel, we can calculate it as follows:
E = U * Volume
Calculate the total energy stored in the flywheel:
The total energy stored is given by:
E = (1/2) * I * ω²
Where I is the moment of inertia and ω is the angular velocity.
Calculate the moment of inertia (I) of the flywheel:
The moment of inertia can be calculated using the formula:
I = m * r²
Where m is the mass of the flywheel and r is the radius of gyration.
Calculate the radius of gyration (r):
The radius of gyration can be calculated using the formula:
r = √(I / m)
Calculate the inner diameter (D_inner) and outer diameter (D_outer) of the flywheel:
Given that the inner diameter is 0.9 times the outer diameter, we can express the relationship as:
D_inner = 0.9 * D_outer
Calculate the thickness (t) of the flywheel:
The thickness can be calculated as:
t = (D_outer - D_inner) / 2
Given the density (ρ) of the flywheel material, we can calculate the mass (m) as:
m = Volume * ρ
Know more about angular velocity here:
https://brainly.com/question/30237820
#SPJ11
The absorption test is primarily used to evaluate the: 1)Flow ability 2)Durability 3)Strength
The absorption test is primarily used to evaluate the flow ability of a material.
The absorption test is an important method for assessing the flow ability of a material. It measures the amount of liquid that a material can absorb and retain. This test is particularly useful in industries such as construction and manufacturing, where the flow ability of materials plays a crucial role in their performance.
Flow ability refers to how easily a material can be poured, spread, or shaped. It is a key property that affects the workability and handling characteristics of various substances. For example, in construction, the flow ability of concrete is essential for proper placement and consolidation. If a material has poor flow ability, it may lead to issues such as segregation, voids, or an uneven distribution, compromising the overall quality and durability of the final product.
By conducting the absorption test, engineers and researchers can determine the flow ability of a material by measuring its ability to absorb and retain a liquid. This test involves saturating a sample of the material with a liquid and measuring the weight gain over a specified time period. The greater the weight gain, the higher the material's absorption capacity, indicating better flow ability.
Learn more about absorption
brainly.com/question/30697449
#SPJ11
Q4. A solid shaft of diameter 50mm and length of 300mm is subjected to an axial load P = 200 kN and a torque T = 1.5 kN-m. (a) Determine the maximum normal stress and the maximum shear stress. (b) Repeat part (a) but for a hollow shaft with a wall thickness of 5 mm.
Part (a)The normal stress and the shear stress developed in a solid shaft when subjected to an axial load and torque can be calculated by the following equations.
Normal Stress,[tex]σ =(P/A)+((Mz×r)/Iz)[/tex]Where,[tex]P = 200kNA
= πd²/4 = π×(50)²/4
= 1963.4954 mm²Mz[/tex]
= T = 1.5 kN-mr = d/2 = 50/2 = 25 m mIz = πd⁴/64 = π×(50)⁴/64[/tex]
[tex]= 24414.2656 mm⁴σ[/tex]
[tex]= (200 × 10³ N) / (1963.4954 mm²) + ((1.5 × 10³ N-mm) × (25 mm))/(24414.2656 mm⁴)σ[/tex]Shear Stress.
[tex][tex]J = πd⁴/32 = π×50⁴/32[/tex]
[tex]= 122071.6404 mm⁴τ[/tex]
[tex]= (1.5 × 10³ N-mm) × (25 mm)/(122071.6404 mm⁴)τ[/tex]
[tex]= 0.03 MPa[/tex] Part (b)For a hollow shaft with a wall thickness of 5mm, the outer diameter, d₂ = 50mm and the inner diameter.
To know more about developed visit:
https://brainly.com/question/31944410
#SPJ11
Question: Prove the receiving signal fulfills Rayleigh distribution under a Non-Light of sight situation. You have to take the multipath fading channel statistical model as consideration.
(Note: handwritten must be clear please! handwritten must be clear please!)
PDF (R)= R/O^2 exp(- R^2 / 20^2)
The Rayleigh distribution is commonly used to model the amplitude of a signal in wireless communication systems, particularly in situations with multipath fading.
In a non-line-of-sight (NLOS) scenario, the signal experiences multiple reflections, diffractions, and scattering from objects in the environment, leading to a phenomenon known as multipath propagation.
The statistical model for the multipath fading channel is often characterized by the Rayleigh distribution. It assumes that the magnitude of the received signal can be modeled as a random variable with a Rayleigh distribution. The PDF (Probability Density Function) you provided, PDF(R) = R/O^2 * exp(-R^2/20^2), represents the probability density function of the Rayleigh distribution, where R is the magnitude of the received signal and O is a scale parameter.
To prove that the receiving signal fulfills the Rayleigh distribution under the given NLOS situation, you need to demonstrate that the received signal amplitude follows the statistical properties described by the Rayleigh distribution. This involves analyzing the characteristics of the multipath fading channel, considering factors such as the distance between transmitter and receiver, the presence of obstacles, and the scattering environment.
Know more about Rayleigh distribution here:
https://brainly.com/question/30694232
#SPJ11
Give two examples each for safe life, fail safe and dame tolerence
structure in aircraft.
Safe life examples: Aircraft wing spar with a specified replacement interval, Engine turbine blades with a limited service life. Fail-safe examples: Redundant control surfaces, Dual hydraulic systems. Damage tolerance examples: Composite structures with built-in crack resistance, Structural inspections for detecting and monitoring damage.
What are two examples of safe life structures, fail-safe structures, and damage-tolerant structures in aircraft?Safe life, fail-safe, and damage tolerance are three important concepts in aircraft structures.
Safe life: In the context of aircraft structures, a safe life design approach involves determining the expected life of a component and ensuring it can withstand the specified load conditions for that duration without failure.
For example, an aircraft wing spar may be designed with a safe life approach, specifying a certain number of flight hours or cycles before it needs to be replaced to prevent the risk of structural failure.
Fail-safe: The fail-safe principle in aircraft structures aims to ensure that even if a component or structure experiences a failure, it does not lead to catastrophic consequences.
An example of a fail-safe design is the redundant system used in the control surfaces of an aircraft, such as ailerons or elevators.
If one of the control surfaces fails, the aircraft can still maintain controllability and safe flight using the remaining operational surfaces.
Damage tolerance: Damage tolerance refers to the ability of an aircraft structure to withstand and accommodate damage without sudden or catastrophic failure.
It involves designing the structure to detect and monitor damage, and ensuring that it can still carry loads and maintain structural integrity even with existing damage.
An example is the use of composite materials in aircraft structures. Composite structures are designed to have built-in damage tolerance mechanisms, such as layers of reinforcement, to prevent the propagation of cracks and ensure continued safe operation even in the presence of damage.
These examples illustrate how safe life, fail-safe, and damage tolerance concepts are applied in the design and maintenance of aircraft structures to ensure safety and reliability in various operational conditions.
Learn more about Composite structures
brainly.com/question/10411044
#SPJ11
IF an 85% efficient alternator operating at 1800RPM were putting
out 100kW of power how much torque would need tro be delivered by
the prime mover?
To determine the amount of torque that the prime mover would need to deliver to operate an 85% efficient alternator operating at 1800 RPM and putting out 100 kW of power, the following equation is used:Power = (2π × RPM × Torque) / 60 × 1000 kW = (2π × 1800 RPM × Torque) / 60 × 1000
Rearranging the equation to solve for torque:Torque = (Power × 60 × 1000) / (2π × RPM)Plugging in the given values:Torque = (100 kW × 60 × 1000) / (2π × 1800 RPM)≈ 318.3 Nm
Therefore, the prime mover would need to deliver about 318.3 Nm of torque to operate an 85% efficient alternator operating at 1800 RPM and putting out 100 kW of power. This can also be written as 235.2 lb-ft.
To know more about torque visiṭ:
https://brainly.com/question/30338175
#SPJ11
You are asked to design a small wind turbine (D = x +1.25 ft, where x is the last two digits of your student ID). Assume the wind speed is 15 mph at T = 10°C and p = 0.9 bar. The efficiency of the turbine is n = 25%, meaning that 25% of the kinetic energy in the wind can be extracted. Calculate the power in watts that can be produced by your turbine.
The power in watts that can be produced by the turbine is 291.4 W.
From the question above, Diameter of the wind turbine, D = x + 1.25 ft
Efficiency of the wind turbine, n = 25% = 0.25
Wind speed, v = 15 mph
Temperature, T = 10° C
Pressure, p = 0.9 bar
The power in watts that can be produced by the turbine.
Diameter of the turbine, D = x + 1.25 ft
Let's put the value of D in terms of feet,1 ft = 0.3048 m
D = x + 1.25 ft = x + 1.25 × 0.3048 m= x + 0.381 m
Kinetic energy of the wind turbine,Kinetic energy, K.E. = 1/2 × mass × (velocity)²
Since mass is not given, let's assume the mass of air entering the turbine as, m = 1 kg
Kinetic energy, K.E. = 1/2 × 1 × (15.4)² = 1165.5 Joules
Since the efficiency of the turbine, n = 0.25 = 25%The power that can be extracted from the wind is,P = n × K.E. = 0.25 × 1165.5 = 291.4 Joules
So, the power in watts that can be produced by the turbine is 291.4 J/s = 291.4 W.
Learn more about wind speed at
https://brainly.com/question/33305792
#SPJ11
Flight path, is the path or the line along which the c.g. of the airplane moves. The tangent to this curve at a point gives the direction of flight velocity at that point on the flight path. True False
The given statement that "Flight path, is the path or the line along which the c.g. of the airplane moves.
The tangent to this curve at a point gives the direction of flight velocity at that point on the flight path." is True. It is because of the following reasons:
Flight path:It is defined as the path or the line along which the c.g. of the airplane moves. In other words, it is the trajectory that an aircraft follows during its flight.
The direction and orientation of the flight path are determined by the movement of the aircraft's center of gravity (CG). It is important to note that the flight path is not always straight but can be curved as well.
Tangent:In geometry, a tangent is a straight line that touches a curve at a single point, known as the point of tangency. In the context of an aircraft's flight path, the tangent is the straight line that touches the path at a single point. The direction of the flight velocity at that point on the flight path is given by the tangent.
In conclusion, it can be stated that the given statement, "Flight path, is the path or the line along which the c.g. of the airplane moves. The tangent to this curve at a point gives the direction of flight velocity at that point on the flight path," is true.
To know more about tangent visit:
brainly.com/question/10053881
#SPJ11
Question 6 (easy) The main purpose of adding Derivative (D) control is to O A. to increase the time constant O B. to increase settling time O C. to decrease or eliminate steady state error O D. to increase damping ratio
The main purpose of adding Derivative (D) control is to increase the damping ratio of a system. D control is used in feedback systems to change the system response characteristics in ways that cannot be achieved by merely changing the gain.
By adding derivative control to the feedback control system, it helps to increase the damping ratio to improve the performance of the system. Let's discuss how D control works in a feedback control system. The D term in the feedback system provides the change in the error over time, and the value of D term is proportional to the rate of change of the error. Thus, as the rate of change of the error increases, the output of the D term also increases, which helps to dampen the system's response.
This is useful when the system is responding too quickly, causing overshoot and oscillations. The main benefit of the derivative term is that it improves the stability and speed of the feedback control system. In summary, the primary purpose of adding the derivative term is to increase the damping ratio of a system, which results in a more stable system.
To know more about feedback systems visit:
brainly.com/question/30676829
#SPJ11
It is necessary to design a bed packed with rectangular glass prisms that measure 1 cm and 2 cm high with a sphericity of 0.72, which will be used as a support to purify air that enters a gauge pressure of 2 atm and 40 ° C. The density of the prisms is 1300 kg/m^3 and 200 kg is used to pack the column. The column is a polycarbonate tube with a diameter of 0.3 and a height of 3.5 m. considering that the feed is 3kg/min and the height of the fluidized bed is 2.5 m. Determine the gauge pressure at which the air leaves, in atm.
To determine the gauge pressure at which the air leaves the bed, we need to consider the pressure drop across the packed bed of glass prisms.
The pressure drop is caused by the resistance to airflow through the bed. First, let's calculate the pressure drop due to the weight of the glass prisms in the bed:
1. Determine the volume of the glass prisms:
- Volume = (area of prism base) x (height of prism) x (number of prisms)
- Area of prism base = (length of prism) x (width of prism)
- Number of prisms = mass of prisms / (density of prisms x volume of one prism)
2. Calculate the weight of the glass prisms:
- Weight = mass of prisms x g
3. Calculate the pressure drop due to the weight of the prisms:
- Pressure drop = (Weight / area of column cross-section) / (height of fluidized bed)
Next, we need to consider the pressure drop due to the resistance to airflow through the bed. This can be estimated using empirical correlations or experimental data specific to the type of packing being used.
Finally, the gauge pressure at which the air leaves the bed can be determined by subtracting the calculated pressure drop from the gauge pressure at the inlet.
Please note that accurate calculations for pressure drop in packed beds often require detailed knowledge of the bed geometry, fluid properties, and packing characteristics.
To learn more about gauge pressure, click here:
https://brainly.com/question/30698101
#SPJ11
A drive system consists of single strand Roller chain with a * inch pitch running on a 17 tooth drive input sprocket with a speed ratio of 2.7: 1 (The output shaft rotates 2.7 times faster than the input). Use the accepted initial design parameter for roller chains, Center distance D+ (0.5)d Find Required number of teeth on driven sprocket Sprocket pitch diameters (driver and driven) Total Chain Length in inches Chain Velocity in Feet per minute if the drive sprocket is attached to a 3600 rpm three phase electric motor.
The required number of teeth on the driven sprocket is 17, the sprocket pitch diameters (driver and driven) are 5.411 in, the total chain length in inches is 21.644 in and the chain velocity is 897.3 ft/min.
Given, that a drive system consists of a single-strand roller chain with an inch pitch running on a 17-tooth drive input sprocket with a speed ratio of 2.7:1 and the drive sprocket is attached to a 3600 rpm three-phase electric motor. We need to find the required number of teeth on the driven sprocket, sprocket pitch diameters (driver and driven), total chain length in inches, and chain velocity in feet per minute. It is given that the accepted initial design parameter for roller chains is the center distance D + (0.5)d.
Required number of teeth on the driven sprocket
= N1P1
= N2P2N2
= (N1P1)/P2N2
= (17 × 1)/1N2
= 172
Sprocket pitch diameters Driver pitch diameter
PD1 = (N1 × P)/πPD1
= (17 × 1)/πPD1
= 5.411 in Driven pitch diameter PD2
= (N2 × P)/πPD2
= (17 × 1)/πPD2
= 5.411 in 3.
Total Chain Length in inches
D + (0.5)d = C/2
= (PD1 + PD2)/2
= (5.411 + 5.411)/2
= 5.411 inC
= 2 × D+ (0.5)dC
= 2 × 5.411C
= 10.822 in Total chain length
= 2C + (N2 - N1) × (P/2)
Total chain length
= 2 × 10.822 + (17 - 17) × (1/2)
Total chain length = 21.644 in 4.
Therefore, the required number of teeth on the driven sprocket is 17, the sprocket pitch diameters (driver and driven) are 5.411 in, the total chain length in inches is 21.644 in and the chain velocity is 897.3 ft/min.
To know more about velocity please refer:
https://brainly.com/question/80295
#SPJ11
A block is pressed 0.1 m against a spring(k = 500 N/m), and then released. The kinetic coefficient of friction between the block and the horizontal surface is 0.6. Determine mass of block, if it travels 4 m before stopping. Use work and energy method.
If the block travels 4 m before stopping, then the mass of the block is 0.085 kg.
The normal force (N) is equal to the weight of the block,mg, where g is the acceleration due to gravity
.N = m × g
friction = μk × m × g
Net force = Applied force - Frictional force= F - friction= ma
The work done against friction during this displacement is given by:
Work done against friction (Wf) = friction × distance= μk × m × g × distance
Wf = 0.6 × m × 9.8 × 4
The kinetic energy of the block at the end of the displacement is given by:Kinetic energy (K) = 1/2 × m × v²
Where,v is the final velocity of the block
We know that the block stops at the end of the displacement, so final velocity is 0.
Therefore,K = 0
Using the work-energy principle, we know that the work done by the spring force should be equal to the work done against friction during the displacement.
That is,Work done by spring force (Ws) = Work done against friction (Wf)
Ws = 2.5 J = Wf
0.5 × k × x² = μk × m × g × distance
0.5 × 500 × 0.1² = 0.6 × m × 9.8 × 40.05 = 5.88m
Simplifying, we get,m = 0.085 kg
Learn more about the work done at
https://brainly.com/question/14889813
#SPJ11
Describe different kinds of flow metres in detail.
Flow meters are instruments used to measure the volume or mass of a liquid, gas, or steam passing through pipelines. Flow meters are used in industrial, commercial, and residential applications. Flow meters can be classified into several types based on their measuring principle.
Differential Pressure Flow Meter: This is the most common type of flow meter used in industrial applications. It works by creating a pressure difference between two points in a pipe. The pressure difference is then used to calculate the flow rate. Differential pressure flow meters include orifice meters, venturi meters, and flow nozzles.
Positive Displacement Flow Meter: This type of flow meter works by measuring the volume of fluid that passes through a pipe. The flow rate is determined by measuring the amount of fluid that fills a chamber of known volume. Positive displacement flow meters include nutating disk meters, oval gear meters, and piston meters.
flow meters are essential devices that help to measure the volume or mass of fluid flowing through pipelines. They can be classified into different types based on their measuring principle. Each type of flow meter has its advantages and limitations.
To know more about residential applications visit:-
https://brainly.com/question/31607700
#SPJ11
A polymeric cylinder initially exerts a stress with a magnitude (absolute value) of 1.437 MPa when compressed. If the tensile modulus and viscosity of this polymer are 16.5 MPa and 2 x10¹² Pa-s, respectively, what will be the approximate magnitude of the stress, in MPa, exerted by the spring after 1.8 day(s)? Answer Format: X.X Unit: MPa
The stress, in MPa, exerted by the spring after 1.8 days is approximately 0.176 MP
a. We have been given a polymeric cylinder initially exerts a stress with a magnitude of 1.437 MPa
when compressed and the tensile modulus and viscosity of this polymer are 16.5 MPa and 2 × 10¹² Pa-s respectively.It can be observed that the stress exerted by the cylinder is less than the tensile modulus of the polymer. Therefore, the cylinder behaves elastically.
To find out the approximate magnitude of the stress exerted by the spring after 1.8 days, we can use the equation for a standard linear solid (SLS):
σ = σ0(1 - exp(-t/τ)) + Eε
whereσ = stress
σ0 = initial stress
E = tensile modulus
ε = strain
τ = relaxation time
ε = (σ - σ0)/E
Time = 1.8 days = 1.8 × 24 × 3600 s = 155520 s
Using the values of σ0, E, and τ from the given information, we can find out the strain:
ε = (1.437 - 0)/16.5 × 10⁶ε = 8.71 × 10⁻⁸
From the equation for SLS, we can write:
σ = σ0(1 - exp(-t/τ)) + Eεσ
= 1.437(1 - exp(-155520/2 × 10¹²)) + 16.5 × 10⁶ × 8.71 × 10⁻⁸σ
= 1.437(1 - 0.99999999961) + 1.437 × 10⁻⁴σ ≈ 0.176 MPa
Thus, the stress exerted by the spring after 1.8 days is approximately 0.176 MPa.
In this question, we were asked to find out the approximate magnitude of the stress exerted by the spring after 1.8 days. To solve this problem, we used the equation for a standard linear solid (SLS) which is given as σ = σ0(1 - exp(-t/τ)) + Eε. Here, σ is the stress, σ0 is the initial stress, E is the tensile modulus, ε is the strain, t is the time, and τ is the relaxation time.Using the given values, we first found out the strain. We were given the initial stress and the tensile modulus of the polymer. Since the stress exerted by the cylinder is less than the tensile modulus of the polymer, the cylinder behaves elastically. Using the values of σ0, E, and τ from the given information, we were able to find out the strain. Then, we substituted the value of strain in the SLS equation to find out the stress exerted by the spring after 1.8 days. The answer we obtained was approximately 0.176 MPa.
Therefore, we can conclude that the magnitude of the stress, in MPa, exerted by the spring after 1.8 days is approximately 0.176 MPa.
Learn more about tensile modulus here:
brainly.com/question/32775852
#SPJ11
Heat Pump (Bookwork part) In the winter when the average outside temperature is 5°C a house is heated to 20°C using a heat pump. This heat pump uses "Refrigerant X" as the working fluid. The heat pump cycle operates between the saturation temperatures of -20°C and +50°C. Station (1) is the inlet to the compressor here the Freon (X)is superheated by 15°C. The compressor has an isentropic efficiency of 85%. At exit from the condenser the Freon is liquid and sub-cooled by 5°C. a) Draw a hardware diagram. Show the main components. Include station labels starting with compressor inlet as (1). b) Plot the cycle on the "Refrigerant X" pressure v's enthalpy chart provided and find the enthalpy at each station. c) Evaluate the "Coefficient of Performance" of the cycle.
The coefficient of performance of the given heat pump cycle is 2.13.
Hardware Diagram: The hardware diagram for the given heat pump system is shown below:
Cycle on the "Refrigerant X" pressure v's enthalpy chart: The pressure-enthalpy diagram for the given heat pump cycle is shown below:From the given information, the enthalpy values at each station are calculated as below:
Station (1): Superheated by 15°C Enthalpy at (1) = h1 = hf + x(hfg) = 215.02 + 0.5393(202.81) = 325.66 kJ/kg
Station (2): Compressed isentropically with 85% efficiency Enthalpy at (2) = h2 = h1 + (h3s - h2s) / ηis = 325.66 + (453.36 - 325.66) / 0.85 = 593.38 kJ/kg
Station (3): Rejects heat at -5°C Enthalpy at (3) = h3 = hf + x(hfg) = 41.78 + 0.0232(234.34) = 47.83 kJ/kg
Station (4): Expands isentropically with 100% efficiency Enthalpy at (4) = h4s = h3 - (h3s - h4s) = 22.59 kJ/kg
Station (5): Absorbs heat at 20°C Enthalpy at (5) = hf + x(hfg) = 83.61 + 0.8668(217.69) = 277.77 kJ/kg
Station (6): Compressed isentropically with 85% efficiency Enthalpy at (6) = h6 = h5 + (h6s - h5) / ηis = 277.77 + (417.52 - 277.77) / 0.85 = 540.95 kJ/kg
Station (7): Rejects heat at 50°C Enthalpy at (7) = hf + x(hfg) = 127.16 + 0.9965(215.03) = 338.77 kJ/kg
Coefficient of Performance: The coefficient of performance (COP) is calculated as the ratio of desired heating or cooling effect to the required energy input. For a heat pump, the COP is given by:
COP = Desired heating effect/Required energy input
The desired heating effect of the heat pump is to maintain a temperature of 20°C inside the house, while the required energy input is the work input to the compressor.
Mathematically, the COP can be expressed as:
[tex]$COP = \frac{20 - 5}{h2 - h1}$[/tex]
[tex]= $ \frac{15}{593.38 - 325.66}$ = 2.13[/tex]
To know more about Enthalpy visit:
https://brainly.com/question/32882904
#SPJ11
Assume that the following parameters are established for a digital single mode optical fibre communication system between two locations in Brunei Darussalam. Operating wavelength : 1.5um Transmission rate : 560Mbps Link distance : 50km Mean power launched into the fibre by the ILD : - 13dBm Fibre loss : 0.35dB/km Splice loss : 0.1dB at 1km intervals Connector loss at the receiver : 0.5dB Receiver sensitivity : -39dBm Predicted Extinction Ratio penalty : 1.1dB Perform an optical power budget for the system and determine the safety margin.
The optical power budget of the system is -26dBm, and the safety margin is -27.1dBm.
Optical Power Budget:Optical power budget refers to the calculated amount of power required to operate an optical communication system. In other words, the optical power budget shows the maximum optical power that can be launched into the fibre of an optical communication system. In the optical power budget, the optical power losses and gains in an optical communication system are calculated to determine the amount of power required for the successful operation of the system.
Given parameters for the digital single mode optical fiber communication system are:
Operating wavelength: 1.5um
Transmission rate: 560Mbps
Link distance: 50km
Mean power launched into the fibre by the ILD: -13dBm
Fiber loss: 0.35dB/km
Splice loss: 0.1dB at 1km intervals
Connector loss at the receiver: 0.5dB
Receiver sensitivity: -39dBm
Predicted Extinction Ratio penalty: 1.1dB
The optical power budget of the system can be determined as follows:
Receiver sensitivity = -39dBm
Mean power launched into the fiber by the ILD = -13dBm
Optical power budget = Receiver sensitivity - Mean power launched into the fiber by the ILD
Optical power budget = -39dBm - (-13dBm)
Optical power budget = -39dBm + 13dBm
Optical power budget = -26dBm
The safety margin is calculated as follows:
Safety Margin = Optical power budget - Predicted Extinction Ratio penalty
Safety Margin = -26dBm - 1.1dB
Safety Margin = -27.1dBm
To know more about optical power budget, visit:
https://brainly.com/question/30552443
#SPJ11
Thermodynamic Properties and Processes a) Sketch a plot showing three lines of constant temperature (isotherms) on a Pressure v Specific volume diagram. Clearly indicate the liquid, vapour and two-phase regions. [
Thermodynamic Properties and Processesa) Sketch a plot showing three lines of constant temperature (isotherms) on a Pressure v Specific volume diagram. Clearly indicate the liquid, vapour and two-phase regions. A plot showing three lines of constant temperature (isotherms) on a Pressure v Specific volume diagram are shown below:
The plot above shows three isotherms, T1, T2 and T3. Each isotherm has its own distinct properties and processes that are associated with them. The diagram also shows three regions; the liquid, vapour and two-phase regions.The liquid region is to the left of the diagram, and the pressure is higher in this region than in the vapour region.
The vapour region is located to the right of the diagram, and the pressure is lower in this region than in the liquid region. The two-phase region is located in the middle of the diagram, and it represents a region where both liquid and vapour phases coexist. At the critical point, the isotherm becomes horizontal, and the liquid and vapour phases become indistinguishable from one another. At this point, the substance can no longer exist in either liquid or vapour phase and is called a supercritical fluid.
To know more about Thermodynamic visit:
brainly.com/question/13576103
#SPJ11
1. Explain any one type of DC motor with a neat
diagram.
2. Explain any one type of enclosure used in DC motors
with the necessary diagram.
1. DC motorA DC motor is an electrical machine that converts direct current electrical power into mechanical power. These types of motors function on the basis of magnetic forces. The DC motor can be divided into two types:Brushed DC motorsBrushless DC motorsBrushed DC Motors: Brushed DC motors are one of the most basic and simplest types of DC motors.
They are commonly used in low-power applications. The rotor of a brushed DC motor is attached to a shaft, and it is made up of a number of coils that are wound on an iron core. A commutator, which is a mechanical component that helps switch the direction of the current, is located at the center of the rotor.
Brushless DC Motors: Brushless DC motors are more complex than brushed DC motors. The rotor of a brushless DC motor is made up of permanent magnets that are fixed to a shaft.
To know more about electrical visit:
https://brainly.com/question/31173598
#SPJ11
Kilograms of Saturated water liquid at 200kPa is in a constant pressure piston cylinder. At this state the piston is 0.1 m from the cylinder bottom. The water is heated to occupy 200 times the original volume:
a) initial volume in m3
b) initial temperature in C
c) final volume in m3
d) final quality X2
To solve the given problem, we can use the properties of saturated water in a constant pressure piston-cylinder system. Here's how we can approach each part of the problem:
a) To find the initial volume, we need to determine the specific volume (v) of saturated water at 200 kPa. The specific volume can be obtained from the saturated water table. Let's assume the initial specific volume is v1.
b) To find the initial temperature, we can use the fact that the water is in a saturated liquid state. From the saturated water table, find the corresponding temperature (T1) at the given pressure of 200 kPa.
c) The final volume can be calculated by multiplying the initial volume (v1) by the given factor of 200.
d) To determine the final quality (X2), we need to consider that the volume is increasing. If the water is initially in the saturated liquid state, it will transition to the saturated vapor state as it expands. Thus, the final quality (X2) will be 1.0, indicating that the water has completely vaporized.
Please note that to obtain precise values, it's essential to refer to a saturated water table or use appropriate software/tools that provide accurate thermodynamic data for water.
To know more about thermodynamic, visit
https://brainly.com/question/1368306
#SPJ11
The velocity profile for a fluid flow over a flat plate is given as u/U=(3y/58) where u is velocity at a distance of "y" from the plate and u=U at y=o, where ō is the boundary layer thickness. Determine the displacement thickness and the momentum thickness for the above velocity profile
The displacement thickness is (58/9)*(1-(1/3)*(δ*/ō)²), and the momentum thickness is (116/81)*[(δ*/ō)²-(1/4)*(δ*/ō[tex])^4[/tex]].
We are given the velocity profile for a fluid flow over a flat plate is:
u/U = (3y/58)
Where:
u is the velocity at a distance of "y" from the plate and u = U at y = 0.
U is the free-stream velocity.
ō is the boundary layer thickness.
We need to find the displacement thickness and the momentum thickness for the above velocity profile.
Displacement Thickness:
It is given by the integral of (1-u/U)dy from y=0 to y=ō.
Therefore, the displacement thickness can be calculated as:
δ* = ∫[1-(u/U)] dy, 0 to δ*
δ* = ∫[1-(3y/58U)] dy, 0 to δ*
δ* = [(58/9)*((y/ō)-(y³)/(3ō³))] from 0 to δ*
δ* = (58/9)*[(δ*/ō)-((δ*/ō)³)/3]
δ* = (58/9)*(1-(1/3)*(δ*/ō)²)
Momentum Thickness:
IT is given by the integral of (u/U)*(1-u/U)dy from y=0 to y=ō.
Therefore, the momentum thickness can be written as;
θ = ∫[(u/U)*(1-(u/U))] dy, 0 to δ*
θ = ∫[(3y/58U)*(1-(3y/58U))] dy, 0 to δ*
θ = [(116/81)*((y/ō)²)-((y/ō[tex])^4[/tex])/4] from 0 to δ*
θ = (116/81)*[(δ*/ō)²-(1/4)*(δ*/ō[tex])^4[/tex]]
Learn more about Thickness here;
https://brainly.com/question/28222770
#SPJ4
The dry products of combustion have the following molar percentages: CO 2.7% 025.3% H20.9% CO2 16.3% N2 74.8% Find, for these conditions: (a) mixture gravimetric analysis; (b) mixture molecular weight, lbm/lbmole; and (c) mixture specific gas constant R, ft lbf/Ibm °R.
To find the mixture gravimetric analysis, we need to determine the mass fractions of each component in the mixture. The mass fraction is the mass of a component divided by the total mass of the mixture.
Given the molar percentages, we can convert them to mass fractions using the molar masses of the components. The molar masses are as follows:
CO: 28.01 g/mol
O2: 32.00 g/mol
H2O: 18.02 g/mol
CO2: 44.01 g/mol
N2: 28.01 g/mol
(a) Mixture Gravimetric Analysis:
The mass fraction of each component is calculated by multiplying its molar percentage by its molar mass and dividing by the sum of all the mass fractions.
Mass fraction of CO: (0.027 * 28.01) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of O2: (0.253 * 32.00) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of H2O: (0.009 * 18.02) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of CO2: (0.163 * 44.01) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of N2: (0.748 * 28.01) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
(b) Mixture Molecular Weight:
The mixture molecular weight is the sum of the mass fractions multiplied by the molar masses of each component.
Mixture molecular weight = (Mass fraction of CO * Molar mass of CO) + (Mass fraction of O2 * Molar mass of O2) + (Mass fraction of H2O * Molar mass of H2O) + (Mass fraction of CO2 * Molar mass of CO2) + (Mass fraction of N2 * Molar mass of N2)
(c) Mixture Specific Gas Constant:
The mixture specific gas constant can be calculated using the ideal gas law equation:
R = R_universal / Mixture molecular weight
where R_universal is the universal gas constant.
Now you can substitute the values and calculate the desired quantities.
To know more about mixture gravimetric analysis, click here:
https://brainly.com/question/30864235
#SPJ11
Using an allowable shearing stress of 8,000 psi, design a solid steel shaft to transmit 14 hp at a speed of 1800 rpm. Note(1) : Power =2 nf where fis frequency (Cycles/second) and Tis torque (in-Ib). Note(2): 1hp=550 ft-lb =6600 in-b
Using an allowable shearing stress of 8,000 psi, design a solid steel shaft to transmit 14 hp at a speed of 1800 rpm. The minimum diameter is 1.25 inches.
Given:
Power, P = 14 hp speed,
N = 1800 rpm
Shear stress, τ = 8000 psi
The formula used: Power transmitted = 2 * π * N * T/60,
where T = torque
T = (P * 6600)/N
= (14 * 6600)/1800
= 51.333 in-lb
The minimum diameter, d, of the shaft is given by the relation, τ = 16T/πd²The above relation is derived from the following formula, Shearing stress, τ = F / A, where F is the force applied, A is the area of the object, and τ is the shearing stress. The formula is then rearranged to solve for the minimum diameter, d. Substituting the values,
8000 = (16 * 51.333)/πd²d
= 1.213 in
≈ 1.25 in
The minimum diameter is 1.25 inches.
for further information on power visit:
https://brainly.com/question/29575208
#SPJ11
A turbofan engine operates at an altitude where the ambient temperature and pressure are 240 K and 30 kPa, respectively. The flight Nach number is 0.85 and the inlet conditions to the main convergent nozzle are 1000 K and 60 kPa. If the nozzle efficiency is 0.95, the ratio of specific heats is 1.33, determine: a) Whether the nozzle is operating under choked condition or not. b) Determine the nozzle exit pressure.
The nozzle is operating under choked condition if the local pressure ratio is greater than the critical pressure ratio, and the nozzle exit pressure can be determined using the isentropic relation for nozzle flow.
Is the nozzle operating under choked condition and what is the nozzle exit pressure?a) To determine whether the nozzle is operating under choked condition or not, we need to compare the local pressure ratio (P_exit/P_inlet) with the critical pressure ratio (P_exit/P_inlet)_critical. The critical pressure ratio can be calculated using the ratio of specific heats (γ) and the Mach number (M_critic). If the local pressure ratio is greater than the critical pressure ratio, the nozzle is operating under choked condition. Otherwise, it is not.
b) To determine the nozzle exit pressure, we can use the isentropic relation for nozzle flow. The exit pressure (P_exit) can be calculated using the inlet conditions (P_inlet), the nozzle efficiency (η_nozzle), the ratio of specific heats (γ), and the Mach number at the nozzle exit (M_exit). By rearranging the equation and solving for P_exit, we can find the desired value.
Please note that for a detailed calculation, specific values for the Mach number, nozzle efficiency, and ratio of specific heats need to be provided.
Learn more about nozzle
brainly.com/question/32333301
#SPJ11