Answer:
The possible solution is to balance the rate of water removal from the well to the rate of natural recharge of the well from its underground aquifer.
Explanation:
A well is an excavation in the earth, made with the aim of extracting water from the aquifers. The water from a well can be drawn up by the means of a pump, containers, such as buckets, or by hand. Aquifers can also be recharged through a well.
Well draw down occurs when water from the well is drained faster than it is naturally recharged from the aquifer. This can be as a result of over pumping, extended drought, among other factors. The use of the high-powered motor in this case, for pumping, might be the possible cause of the well drying up. The situation might have resulted from the pump drawing out water from the well at a rate tat exceeds the rate at which it is recharged naturally, causing the well water to start drying up. There's also a possibility that the well is pumped indiscriminately, possibly leading to wastage of water.
The solution to this problem is to give the well a time duration for it to recharge itself. Then, the rate of recharges should be calculated and determined by an hydrologist. When all these is done, a pump with a motor power that does not exceed the calculated recharge rate should be used in place of the high-powered motor. Also, water usage should be brought to the minimum level to prevent unnecessary pumping due to excessive, wasteful use of water.
Assume that a nickel weighs exactly 5.038650 g for the sets of weights listed below obtained by a single weighing on the balance below
Answer:
afshkkyfugutuiryfyi
Determine the volume occupied by 10 mol of helium at
27 ° C and 82 atm
Answer:
3.00 L
Explanation:
PV = nRT
(82 atm × 101325 Pa/atm) V = (10 mol) (8.314 J/mol/K) (27 + 273) K
V = 0.00300 m³
V = 3.00 L
A 400 mL sample of hydrogen gas is collected over water at 20°C and 760 torr the vapor pressure of water at 20°C is 17.5 torr. what volume will the dry hydrogen gas occupy at 20°C and 760 torr?
Answer:
V2 = 17371.43ml
Explanation:
We use Boyles laws
since temperature is constant
P1V1=P2V2
760 x 400 = 17.5 x V2
304000 = 17.5 x V2
V2 = 304000/17.5
V2 = 17371.43ml
The volume will the dry hydrogen gas occupy at the temperature of 20°C and vapor pressure at 760 torrs will be 18 ml.
What is vapor pressure?
The vapor pressure of a liquid is independent of the volume of liquid in the container, whether one liter or thirty liters; both samples will have the same vapor pressure at the same temperature.
The temperature has an exponential connection with vapor pressure, which means that as the temperature rises, the vapor pressure rises as well the equation is -
P1 V1 / T1 = P2 V2 / T1
here, P = pressure
T = temperature
V = volume
substituting the value in the equation,
400 ×760 / 20 = 17.5× V / 20
V = 400× 760 / 20 × 17.5 / 20
V = 18 ml
Therefore the volume of the hydrogen gas remaining at this temperature will be 18 ml.
learn more about vapor pressure, here :
https://brainly.com/question/27682495
#SPJ5
Find the [OH−] of a 0.32 M methylamine (CH3NH2) solution. (The value of Kb for methylamine (CH3NH2) is 4.4×10−4.) Express your answer to two significant figures and include the appropriate units.
Answer:
[tex][OH^-]=0.01165M[/tex]
Explanation:
Hello,
In this case, for the dissociation of methylamine:
[tex]CH_3NH_2(aq)+H_2O(l)\rightleftharpoons CH_3NH_3^+(aq)+OH^-(aq)[/tex]
We can write the basic dissociation constant as:
[tex]Kb=\frac{[CH_3NH_3^+][OH^-]}{[CH_3NH_2]}[/tex]
That in terms of the reaction extent [tex]x[/tex], turns out:
[tex]Kb=\frac{x*x}{[CH_3NH_2]_0-x}[/tex]
[tex]4.4x10^{-4}=\frac{x^2}{0.32M-x}[/tex]
That has the following solution for [tex]x[/tex]:
[tex]x_1=-0.01209M\\x_2=0.01165M[/tex]
Yer 0.01165M is valid only as no negative concentrations are eligible. It means that it is the concentration of hydroxyl ions in the solution:
[tex][OH^-]=0.01165M[/tex]
Best regards.
Sulfuric acid is commonly used as an electrolyte in car batteries. Suppose you spill some on your garage floor. Before cleaning it up, you wisely decide to neutralize it with sodium bicarbonate (baking soda) from your kitchen. The reaction of sodium bicarbonate and sulfuric acid is
Answer:
The mass of NaHCO3 required is 235.22 g
Explanation:
*******
Continuation of Question:
2NaHCO3(s) + H2SO4(aq) → Na2SO4(aq) + 2CO2(g) + 2H2O(l)
You estimate that your acid spill contains about 1.4 mol H2SO4. What mass of NaHCO3 do you need to neutralize the acid?
********\
The question requires us to calculate the mass of NaHCO3 to neutralize the acid.
From the balanced chemical equation;
1 mol of H2SO4 requires 2 mol of NaHCO3
1.4 would require x?
Upon solving for x we have;
x = 1.4 * 2 = 2.8 mol of NaHCO3
The relationship between mass and number of moles is given as;
Mass = Number of moles * Molar mass
Mass = 2.8 mol * 84.007 g/mol
Mass = 235.22 g
Given a fixed amount of gas help at a constant pressure, calculate the temperature to which the gas would have to be changed if a 1.75 L sample at 23.0*C were to have a final volume of 3.50 L.
A. 46.0*C
B. 89.5*C
C. 169*C
D. 319*C
E. 592*C
Answer:
592 K or 319° C
Explanation:
From the statement of Charles law we know that the volume of a given mass of gas is directly proportional to its absolute temperature at constant pressure. Thus;
V1/T1= V2/T2
Initial volume V1 = 1.75 L
Initial temperature T1= 23.0 +273 = 296 K
Final volume V2= 3.50 L
Final temperature T2 = the unknown
T2= V2T1/V1= 3.50 × 296 / 1.75
T2 = 592 K or 319° C
Question 14 of 25
What type of reaction is BaCl2 + Na,504 → 2NaCl + Baso,?
A. Single-replacement
B. Synthesis
C. Double-replacement
D. Decomposition
double displacement
bcoz each of the reactants combines with other reactants to obtain the product
Which of the following is an alkaline earth metal?
A. Silicon (Si)
B. Magnesium (Mg)
C. Carbon (C)
D. Aluminum (AI)
Answer:
B
Explanation:
The alkaline earth metals are the elements located in Group 2. The only element out of our choices that is in Group 2 is Magnesium.
Nitrogen has different oxidation states in the following compounds: nitrite ion, nitrous oxide, nitrate ion, ammonia, and nitrogen gas. Arrange these species in order of increasing nitrogen oxidation state. Select the correct answer below: A. ammonia, nitrogen gas, nitrite, nitrous oxide, nitrate B. nitrogen gas, ammonia, nitrous oxide, nitrite, nitrate C. ammonia, nitrogen gas, nitrous oxide, nitrite, nitrate D. ammonia, nitrogen gas, nitrate, nitrite, nitrous oxide
Answer:
C. ammonia, nitrogen gas, nitrous oxide, nitrite, nitrate
Explanation:
To establish the oxidation number of nitrogen in each compound, we know that the sum of the oxidation numbers of the elements is equal to the charge of the species.
Nitrite ion (NO₂⁻)
1 × N + 2 × O = -1
1 × N + 2 × (-2) = -1
N = +3
Nitrous oxide (NO)
1 × N + 1 × O = 0
1 × N + 1 × (-2) = 0
N = +2
Nitrate ion (NO₃⁻)
1 × N + 3 × O = -1
1 × N + 3 × (-2) = -1
N = +5
Ammonia (NH₃)
1 × N + 3 × H = 0
1 × N + 3 × (+1) = 0
N = -3
Nitrogen gas (N₂)
2 × N = 0
N = 0
The order of increasing nitrogen oxidation state is:
C. ammonia, nitrogen gas, nitrous oxide, nitrite, nitrate
An analytical laboratory balance typically measures mass to the nearest 0.1 mg. You may want to reference (Page) Section 21.6 while completing this problem. Part A What energy change would accompany the loss of 0.1 mg in mass
Answer:
The energy change is [tex]E = 9.0 *10^{9}\ J[/tex]
Explanation:
From the question we are told that
Mass loss is [tex]m_l = 0.1 \ mg = 0.1 *10^{-3} mkg = 0.1 *10^{-6} \ kg[/tex]
Generally the energy change that would accompany this loss is mathematically represented as
[tex]E = m * c^2[/tex]
Where c is the speed of light with values [tex]c = 3.0*10^{8} \ m/s[/tex]
[tex]E = 0.1 *10^{-6} * [3.0 *10^{8}]^2[/tex]
[tex]E = 9.0 *10^{9}\ J[/tex]
The pH of a solution prepared by mixing 40.00 mL of 0.10 M NH3 with 50.00 mL of 0.10 M NH4Cl and 30mL of 0.05 M H2SO4 is 5.17. Assume that the volume of the solutions are additive . What would be the Ka for NH4
Answer:
Following are the answer to this question:
Explanation:
The value of pH solution is =5.17 So, the p^{OH}:
[tex]p^{OH}[/tex]=14-56.17
=8.823
The volume of the [tex]NH_{3}[/tex] = 40.00 ml
convert into the liter= 0.040L
The value of the concentrated [tex]NH_{3}[/tex] =0.10 M
The volume of the [tex]NH_{4}Cl[/tex]= 50.00 ml
convert into the liter= 0.050L
The value of concentrated [tex]NH_{4}Cl[/tex]= 0.10 M
The volume of the [tex]H_{2}So_{4}[/tex]= 30 ml
convert into the liter= 0.030L
The value of concentrated [tex]H_2So_4[/tex]=0.05 M
Calculating total volume=(0.40+0.050+0.030)
=0.120 L
calculating the new concentrated value of [tex]NH_3[/tex] = [tex]\frac{0.10\times 0.040}{0.120}= 0.33 \ M[/tex]
calculating the new concentrated value of [tex]NH_4Cl[/tex]= [tex]\frac{0.050\times 0.10}{0.120}= 0.04166 \ M[/tex]calculating the new concentrated value of [tex]H_2So_4= \frac{0.030\times 0.05}{0.120}= 0.0125 \ M[/tex] when 1 mol [tex]H_2So_4[/tex] produced 2 mols [tex]H^{+}[/tex] so, 0.0125 in [tex]H_2So_4[/tex]produced:
[tex]=4 \times (2 \times 0.0125) \ mol H^{+}\\\\= 0.025 mol H^{+}[/tex]
create the ICE table:
[tex]NH_3 \ \ \ \ \ \ \ \ + H^{+} \ \ \ \ \ \ \longrightarrow NH_4^{+}[/tex]
I (m) 0.033(m) 0.025 0.04166
C -0.025 -0.025 + 0.025
E 8.3\times 10^{-3} 0 0.0667
now calculating pH:
when ph= 8.83:
[tex]P^{H}= p^{kb}|+ \log\frac{[NH_4^{+}]}{[NH_3]}\\\\8.83=p^{kb}+\log\frac{0.0667}{8.3 \times 10^{-3}}\\\\p^{kb}=8.83-0.9069\\\\ \ \ \ =7.7231 \\\\\ The P^{kb} \ for \ NH_3 \ is =7.7231\\\\\ The P^{kb} \ for N^{+}H_4=14-7.7231\\\\\ \ \ \ \ \ =6.2769[/tex]
Aluminum and oxygen react according to the following equation: 4Al + 3O2 -> 2Al2O3 In a certain experiment, 4.6g Al was reacted with excess oxygen and 6.8g of product was obtained. What was the percent yield of the reaction?
Answer:
Percent yield: 78.2%
Explanation:
Based on the reaction:
4Al + 3O₂ → 2Al₂O₃
4 moles of Al produce 2 moles of Al₂O₃
To find percent yield we need to find theoretical yield (Assuming a yield of 100%) and using:
(Actual yield (6.8g) / Theoretical yield) × 100
Moles of 4.6g of Al (Molar mass: 26.98g/mol) are:
4.6g Al × (1mol / 26.98g) = 0.1705 moles of Al.
As 4 moles of Al produce 2 moles of Al₂O₃, theoretical moles of Al₂O₃ obtained from 0.1705 moles of Al are:
0.17505 moles Al × (2 moles Al₂O₃ / 4 moles Al) = 0.0852 moles of Al₂O₃,
In grams (Molar mass Al₂O₃ = 101.96g/mol):
0.0852 moles of Al₂O₃ × (101.96g / mol) =
8.7g of Al₂O₃ can be produced (Theoretical yield)Thus, Percent yield is:
(6.8g / 8.7g) × 100 =
78.2%Given a fixed amount of gas in a rigid container (no change in volume), what pressure will the gas exert if the pressure is initially 1.50 atm at 22.0oC, and the temperature is changed to 11.0oC?
A. 301 atm
B. 1.56 atm
C. 0.750 atm
D. 1.44 atm
E. 3.00 atm
Answer:
The pressure the gas will have if the pressure is initially 1.50 atm at 22.0 ° C and the temperature changes at 11.0 ° C is 1.44 atm (option D)
Explanation:
Gay Lussac's law indicates that, as long as the volume of the container containing the gas is constant, as the temperature increases, the gas molecules move more rapidly. Then the number of collisions against the walls increases, that is, the pressure increases. That is, the gas pressure is directly proportional to its temperature.
Gay-Lussac's law can be expressed mathematically as follows:
[tex]\frac{P}{T}=k[/tex]
Where P = pressure, T = temperature, K = Constant
You have a gas that is at a pressure P1 and at a temperature T1. When the temperature varies to a new T2 value, then the pressure will change to P2, and then:
[tex]\frac{P1}{T1}=\frac{P2}{T2}[/tex]
In this case:
P1= 1.50 atmT1= 22 °C= 295 °K (being 0°C= 273 °K)P2= ?T2= 11 °C= 284 KReplacing:
[tex]\frac{1.5 atm}{295 K}=\frac{P2}{284 K}[/tex]
Solving:
[tex]P2= 284 K*\frac{1.5 atm}{295 K}[/tex]
P2=1.44 atm
The pressure the gas will have if the pressure is initially 1.50 atm at 22.0 ° C and the temperature changes at 11.0 ° C is 1.44 atm (option D)
A chemist adds of a mercury(I) chloride solution to a reaction flask. Calculate the micromoles of mercury(I) chloride the chemist has added to the flask.
Answer:
3.383x10⁻³ micromoles of HgCl
Explanation:
The chemist adds 170mL of a 1.99x10⁻⁵mmol/L Mercury (I) chloride, HgCl.
The solution contains 1.99x10⁻⁵milimoles of HgCl in 1L. That means in 170mL = 0.170L there are:
0.170L × (1.99x10⁻⁵milimoles HgCl / L) = 3.383x10⁻⁶ milimoles of HgCl.
Now, in 1milimole you have 1000 micromoles. That means in 3.383x10⁻⁶ milimoles of HgCl you have:
3.383x10⁻⁶ milimoles of HgCl ₓ (1000micromoles / 1milimole) =
3.383x10⁻³ micromoles of HgClHow many moles of aqueous magnesium ions and chloride ions are formed when 0.250 mol of magnesium chloride dissolves in water
Answer:
0.250 mol Mg²⁺
0.500 mol Cl⁻
Explanation:
Magnesium chloride (MgCl₂) dissociates into ions according to the following equilibrium:
MgCl₂ ⇒ Mg²⁺ + 2 Cl⁻
1 mol 1 mol 2 mol
1 mol of Mg²⁺ and 2 moles of Cl⁻ are formed per mole of MgCl₂. If we have 0.250 mol of MgCl₂, the following amounts of ions will be formed:
0.250 mol MgCl₂ x 1 mol Mg²⁺/mol MgCl₂= 0.250 mol Mg²⁺
0.250 mol MgCl₂ x 2 mol Cl⁻/mol MgCl₂= 0.500 mol Cl⁻
Answer:
HEY THE ANSWER ABOVE ME IS RIGHT!! i defientely misclicked my rating :/
5/5 all the way.
Explanation:
For each of the processes, determine whether the entropy of the system is increasing or decreasing. The system is underlined.
1. a snowman melts on a spring day
2. a document goes through a paper shredder
3. a water bottle cools down in a refrigerator
4. silver tarnishes
5. dissolved sigar precipitates out of water to form rock candy
A. Entropy is increasing
B. Entropy is decreasing
Entropy is INCREASING when a snowman melts, a document goes through paper shredder, silver tarnishes, while it is DECREASING when dissolved sugar precipitates, water vapor forms droplets and water cools down.
Entropy can be defined as the degree of randomness or disorder of a particular system.
Entropy is equal to zero (0) for a perfectly ordered system.
Heat increases the entropy of the system because more energy excites the molecules and it increases the amount of random activity.
Moreover, the cooling decreases the entropy of the system because molecules are more ordered and it decreases the amount of random activity.
In conclusion, entropy is INCREASING when a snowman melts, a document goes through paper shredder, silver tarnishes, while it is DECREASING when dissolved sugar precipitates, water vapor forms water droplets and the water cools down.
Learn more in:
https://brainly.com/question/490678
Calculate the heat absorbed by a sample of water that has a mass of 45.00 g when the temperature increases from 21.0oC to 38.5 oC. (s=4.184 J/g.o C)
Answer:
The heat absorbed by the sample of water is 3,294.9 J
Explanation:
Calorimetry is the measurement and calculation of the amounts of heat exchanged by a body or a system.
The sensible heat of a body is the amount of heat received or transferred by a body when it undergoes a temperature variation (Δt) without there being a change of physical state (solid, liquid or gaseous). Its mathematical expression is:
Q = c * m * ΔT
Where Q is the heat exchanged by a body of mass m, made up of a specific heat substance c and where ΔT is the temperature variation.
In this case:
Q=?m= 45 gc= 4.184 [tex]\frac{J}{g*C}[/tex]ΔT= Tfinal - Tinitial= 38.5 C - 21 C= 17.5 CReplacing:
Q= 4.184 [tex]\frac{J}{g*C}[/tex] * 45 g* 17.5 C
Solving:
Q=3,294.9 J
The heat absorbed by the sample of water is 3,294.9 J
Suppose of copper(II) acetate is dissolved in of a aqueous solution of sodium chromate. Calculate the final molarity of copper(II) cation in the solution. You can assume the volume of the solution doesn't change when the copper(II) acetate is dissolved in it. Round your answer to significant digit.
Answer:
Molarity Cu²⁺ = 0.423M Cu²⁺
Explanation:
40.8g of copper (II) acetate into 200mL of a 0.700M sodium chromate
The reaction of copper acetate with sodium chromate occurs as follows:
Cu(CH₃COO)₂(aq) + Na₂CrO₄(aq) → CuCrO₄(s) + 2CH₃COONa
In water, the Copper(II) acetate dissociates in Cu²⁺ cation.
To know final molarity of Cu²⁺ we need to calculate the moles of Cu²⁺ that don't react with chromate ion, thus:
Moles of 40.8g of copper(II) acetate (Molar mass: 181.63g/mol) are:
40.8g × (1mol / 181.63g) = 0.2246 moles of Copper(II) acetate
Moles of sodium chromate are:
0.200L ₓ (0.700mol / L) = 0.140 moles of sodium chromate.
As 1 mole of Copper(II) acetate reacts per mole of sodium chromate, moles of Copper(II) acetate = Moles of Cu²⁺ that remains after the reaction are:
0.2246mol - 0.140moles = 0.0846 moles of Cu²⁺
Molarity is ratio between moles of solute (Moles Cu²⁺) and volume in liters of solution (200mL = 0.200L):
Molarity Cu²⁺ = 0.0846 moles / 0.200L
Molarity Cu²⁺ = 0.423M Cu²⁺oxygen get stable configuration by ____________two electrons
please give the answer as fast as you can
please
Answer:
gaining two electrons
Explanation:
electron configuration
2:6
so add two to 6 to get stable 2:8
If D+2 would react with E-1, what do you predict to be the formula?
Answer:
DE2
Explanation: for every one D+2 you need two E-1 because +2=-2
The reaction, 2 SO3(g) <--> 2 SO2(g) + O2(g) is endothermic. Predict what will happen if the temperature is increased.
Explanation:
This reaction is in equilibrium and would hence obey lechatelier's principle. This principle states that whenever a system at equilibrium undergoes a change, it would react in way so as to annul that change.
Since it is an endothermic reaction, increasing the temperature would cause the reaction to shift towards the right.
This means that it favours product formation and more of the product would be formed.
True or False: Adding 4.18 joules to water will increase the temperature more than adding 1 calorie to water.
Answer:
Because one calorie is equal to 4.18 J, it takes 4.18 J to raise the temperature of one gram of water by 1°C. In joules, water's specific heat is 4.18 J per gram per °C. If you look at the specific heat graph shown below, you will see that 4.18 is an unusually large value.
What's the electron configuration of a Ca+2 ion?
A. [Kr]
B. [Ar]
C. [Ne]
D. [He]
Answer:
B
Explanation:
The Ca+2 ion means that 2 electrons have been given away. So when you try and find the answer, you have to count backwards from Calcium. When you do, you get K+ first and then Argon which is either column 8 orc column 18 depending on your periodic table.
The element you hit is Argon.
The answer is B
Answer:
B ar
Explanation:
pen foster answer
If the H+ concentration is 0.00001 M, what is the OH- concentration?
Answer:
1.00x10^-9
Explanation:
1. Suppose 1.00 g of NaOH is used to prepare 250 mL of an NaOH solution. Compare the expected molarity of this solution to the actual average molarity you measured in the standardization. What do you notice
Answer:
0.1M solution of NaOH
Explanation:
1 mole of NaOH - 40g
? moles - 1 g = 1/40 = 0.025 moles.
Molarity of 1.00g of NaOH in 0.25L (250 mL) = no. of moles/volume
= 0.025/0.25
= 0.1M.
Explain why o-vanillin does not fully protonate p-toluidine. Reference appropriate pKa values and include a balanced chemical reaction and an appropriate reaction arrow in your answer.
Answer:
Here's what I get
Explanation:
pKₐ of o-vanillin = 7.81; pKₐ of p-toluidine = 4.44
The higher the pKₐ, the weaker the acid.
Thus, o-vanillin is the weaker acid and has a stronger conjugate base.
The conjugate acid of p-toluidine is the stronger and has the weaker conjugate base.
The equation for the equilibrium is
H-OC₆H₃(OCH₃)CHO + CH₃C₆H₄NH₂ ⇌ ⁻OC₆H₃(OCH₃)CHO + CH₃C₆H₄NH₃⁺
weaker acid weaker base stronger base stronger acid
The reaction between the stronger acid and the stronger base pushes the position of equilibrium to the left.
Thus, o-vanillin does not fully protonate p-toluidine.
O-vanillin is a weaker acid than p-toluidine and has a more stable conjugate base; hence, o-vanillin does not fully protonate p-toluidine.
The pKa is defined as the negative logarithm of Ka. The dissociation constant of an acid Ka shows the extent of dissociation of an acid in solution. The higher the pKa, the lower the Ka and the weaker the acid.
The pKₐ of o-vanillin is 7.81 while the pKₐ of p-toluidine is 4.44. This means that o-vanillin is a weaker acid than p-toluidine and has a more stable conjugate base. Hence, o-vanillin does not fully protonate p-toluidine.
Learn more: https://brainly.com/question/9743981
Which of the following metals is paramagnetic?
A. Magnesium
B. Sodium
C. Beryllium
D. Calcium
Answer:
sodium
Explanation:
(Na) atom is paramagnetic and sodium is a na atom.
Which of the following solutions would have the highest pH? Assume that they are all 0.10 M in acid at 25°C. The acid is followed by its Ka value.
a. HCHO2, 1.8 x 10-4
b. HF, 3.5 x 10-4
c. HClO2, 1.1 x 10-2
d. HCN, 4.9 x 10-10
e. HNO2, 4.6 x 10-4
Answer:
[tex]HCN~~Ka=4.9x10^-^1^0[/tex]
Explanation:
In this case, we have to remember the relationship between the Ka value and the pH. We can use the general reaction for any acid with his Ka value expression:
[tex]HA~->~H^+~+~A^-[/tex] [tex]Ka=\frac{[H^+][A^-]}{[HA]}[/tex]
In the Ka expression, we have a proportional relationship between Ka and the concentration of [tex]H^+[/tex]. Therefore, if we have a higher Ka value we will have a smaller pH (lets keep in mind that with a higher
So, if we have to find the higher pH value we need to search the smaller Ka value in this case [tex]HCN~~Ka=4.9x10^-^1^0[/tex].
I hope helps!
HCN has the highest pH among all the acids listed in the question.
The Ka is called the acid dissociation constant. It shows the extent to which an acid is ionized in water. The pH shows the hydrogen ion concentration of water. The higher the Ka, the higher the hydrogen ion concentration and the lower the pH.
Hence, HCN has the lowest Ka and the lowest hydrogen ion concentration. Therefore, HCN has the highest pH among all the acids listed in the question.
Learn more: https://brainly.com/question/6505878
Sample gas has a volume of 3.40 L at 10°C what will be its volume at 100°C pressure remaining constant
Answer:
V2 = 4.48L
Explanation:
using charles law
V1/T1=V2/T2
3.4/283=V2/373
0.012=V2/373
V2= 0.012 x 373
V2 = 4.48L
Which of these are elimination reactions? Check all that apply.
CH3OH + CH3COOH → CH3CO2CH3 + H20
C3H7OH → C3H6 + H20
H9C2Br + NaOH → C2H4 + NaBr + H20
Answer:
C3H7OH → C3H6 + H20
Explanation:
If we look at the reactant and the product we will realize that the reactant is an alcohol while the product is an alkene. The reaction involves acid catalysed elimination of water from an alcohol.
Water is a good leaving group, hence an important synthetic route to alkenes is the acid catalysed elimination of water from alcohols. Hence the conversion represented by C3H7OH → C3H6 + H20 is an elimination reaction in which water is the leaving group.
Answer:
B and C. Just finished my lesson on Edge.