The rate of change of total enthalpy for this process is 84.35 kW.Processes can be classified as steady or unsteady. In a steady flow process, the flow properties (temperature, pressure.
The energy or mass entering a system is equal to the energy or mass leaving the system. Given the information provided in the question, it is a steady flow process.As per the given data,Mass flow rate = 1.7 kg/sReduced pressure at inlet (P1) = 2Reduced temperature at inlet Reduced temperature at outlet (T2) = 1.7The compressibility factor (Z) can be obtained from the compressibility chart
The compressibility factor at the inlet and outlet can be found as follows:Compressibility factor at inlet, Z1:From the chart .Compressibility factor at outlet, Z2:From the chart, for P2 = 3 and T2 = 1.7, Z2 = 0.97.The specific heat of nitrogen at constant pressure .The rate of change of total enthalpy for this process can be calculated as follows Therefore, the rate of of total enthalpy for this process.
To know more about compressibility visit:
https://brainly.com/question/22170796
#SPJ11
1) An undamped, unforced, spring/mass system has 13 N/m and a mass m 5 kg. The mass is given an initial displacement of x(0) = .01 m, and zero initial velocity, i(t) = 0 at t = 0. Determine the maximum velocity of the mass.
For an undamped, unforced spring/mass system with the given parameters and initial conditions, the maximum velocity of the mass is zero. The spring constant is 13 N/m, and the mass of the system is 5 kg.
The system is initially displaced with a value of 0.01 m and has zero initial velocity. The motion of the mass in an undamped, unforced spring/mass system can be described by the equation:
m * x''(t) + k * x(t) = 0
where m is the mass, x(t) is the displacement of the mass at time t, k is the spring constant, and x''(t) is the second derivative of x with respect to time (acceleration).
To solve for the maximum velocity, we need to find the expression for the velocity of the mass, v(t), which is the first derivative of the displacement with respect to time:
v(t) = x'(t)
To find the maximum velocity, we can differentiate the equation of motion with respect to time:m * x''(t) + k * x(t) = 0
Taking the derivative with respect to time gives:
m * x'''(t) + k * x'(t) = 0
Since the system is undamped and unforced, the third derivative of displacement is zero. Therefore, the equation simplifies to:
k * x'(t) = 0
Solving for x'(t), we find:
x'(t) = 0
This implies that the velocity of the mass is constant and equal to zero throughout the motion. Therefore, the maximum velocity of the mass is zero.
Learn more about displacement here:
https://brainly.com/question/28609499
#SPJ11
why does nano-meter sized grains often contain no
dislocations.
Nanometer-sized grains are small, and their size ranges from 1 to 100 nanometers. These grains often contain no dislocations because they are so small that their dislocation density is low.
As a result, the dislocations tend to be absorbed by the grain boundaries, which act as obstacles for their motion. This is known as a dislocation starvation mechanism.In nanometer-sized grains, the dislocation density is proportional to the grain size, which means that the smaller the grain size, the lower the dislocation density. The reason for this is that the number of dislocations that can fit into a grain is limited by its size.
As the grain size decreases, the dislocation density becomes lower, and eventually, the grain may contain no dislocations at all. The grain boundaries in nanometer-sized grains are also often curved or misaligned, which creates an additional energy barrier for dislocation motion.Dislocations are linear defects that occur in crystalline materials when there is a mismatch between the lattice planes.
They play a crucial role in the deformation behavior of materials, but their presence can also lead to mechanical failure. Nanometer-sized grains with no dislocations may have improved mechanical properties, such as higher strength and hardness. In conclusion, nanometer-sized grains often contain no dislocations due to their small size, which results in a low dislocation density, and the presence of grain boundaries that act as obstacles for dislocation motion.
To know about Nanometer visit:
https://brainly.com/question/13311743
#SPJ11
"What is the magnitude of the inductive reactance XL at a frequency of 10 Hz, if L is 15 H?" O 0.1 ohms O 25 ohms O 0.0011 ohms O 942 48 ohms
Inductive reactance (XL) is a property of an inductor in an electrical circuit. It represents the opposition that an inductor presents to the flow of alternating current (AC) due to the presence of inductance.
The magnitude of the inductive reactance XL at a frequency of 10 Hz, with L = 15 H, is 942.48 ohms.
The inductive reactance (XL) of an inductor is given by the formula:
XL = 2πfL
Where:
XL = Inductive reactance
f = Frequency
L = Inductance
Given:
f = 10 Hz
L = 15 H
Substituting these values into the formula, we can calculate the inductive reactance:
XL = 2π * 10 Hz * 15 H
≈ 2 * 3.14159 * 10 Hz * 15 H
≈ 942.48 ohms
The magnitude of the inductive reactance (XL) at a frequency of 10 Hz, with an inductance (L) of 15 H, is approximately 942.48 ohms.
To know more about alternating current, visit;
https://brainly.com/question/10715323
#SPJ11
(Q4) Explain the roles of a voltage buffer and an · inverting amplifier, each built with peripherals, in constructing an OP AMP and a capacitance multiplier. Why is it impor- tant to make use of a floating capacitor ture? within the structure
In constructing an OP AMP and a capacitance multiplier, the roles of a voltage buffer and an inverting amplifier, each built with peripherals, are explained below. Additionally, the importance of making use of a floating capacitor structure is also explained.
OP AMP construction using Voltage bufferA voltage buffer is a circuit that uses an operational amplifier to provide an idealized gain of 1. Voltage followers are a type of buffer that has a high input impedance and a low output impedance. A voltage buffer is used in the construction of an op-amp. Its main role is to supply the operational amplifier with a consistent and stable power supply. By providing a high-impedance input and a low-impedance output, the voltage buffer maintains the characteristics of the input signal at the output.
This causes the voltage to remain stable throughout the circuit. The voltage buffer is also used to isolate the output of the circuit from the input in the circuit design.OP AMP construction using inverting amplifierAn inverting amplifier is another type of operational amplifier circuit. Its output is proportional to the input signal multiplied by the negative of the gain. Inverting amplifiers are used to amplify and invert the input signal.
To know more about capacitance visit:
brainly.com/question/33281017
#SPJ11
A thin-walled spherical vessel, of internal diameter 10 m and wall thickness 2 cm, is filled with water. Determine the additional water that is required to be pumped into the vessel to raise its internal pressure by 0.5 MPa. Let: E = 200 GPa; K = 2 GPa; v = 0.3. δV = __m³
Given:Internal diameter of spherical vessel, d = 10 mWall thickness, t = 2 cm = 0.02 mInternal pressure, Δp = 0.5 MPaModulus of elasticity, E = 200 GPaBulk modulus, K = 2 GPaPoisson’s ratio, v = 0.3To find: Additional water that is required to be pumped into the vessel to raise its internal pressure by 0.5 MPaChange in volume, δV = .
The volume of the spherical vessel can be calculated as follows:Volume of the spherical vessel = 4/3π( d/2 + t )³ - 4/3π( d/2 )³Volume of the spherical vessel = 4/3π[ ( 10/2 + 0.02 )³ - ( 10/2 )³ ]Volume of the spherical vessel = 4/3π[ ( 5.01 )³ - ( 5 )³ ]Volume of the spherical vessel = 523.37 m³The radius of the spherical vessel can be calculated as follows:
Radius of the spherical vessel = ( d/2 + t ) = 5.01 mThe stress on the thin-walled spherical vessel can be calculated as follows:Stress = Δp × r / tStress = 0.5 × 5.01 / 0.02Stress = 125.25 MPa.
To know more about diameter visit:
https://brainly.com/question/32968193
#SPJ11
Water flows through a long pipe of diameter 10 cm. Assuming fully developed flow and that the pressure gradient along the pipe is 400 Nm−3, perform an overall force balance to show that the frictional stress acting on the pipe wall is 10 Nm−2. What is the velocity gradient at the wall?
The force balance for the flow of fluid in the pipe is given beef = Fo + Where Fb is the balance force in the pipe, is the pressure force acting on the pipe wall, and Ff is the force of frictional stress acting on the pipe wall.
According to the equation = π/4 D² ∆Where D is the diameter of the pipe, ∆P is the pressure gradient, and π/4 D² is the cross-sectional area of the pipe.
At the wall of the pipe, the velocity of the fluid is zero, so the velocity gradient at the wall is given by:μ = (du/dr)r=D/2 = 0, because velocity is zero at the wall. Hence, the velocity gradient at the wall is zero. Therefore, the answer is: The velocity gradient at the wall is zero.
To know more about balance visit:
https://brainly.com/question/27154367
#SPJ11
By using an appropriate method, determine the deflection at the mid-span of the beam and rotation at both ends of the beam. Take Young’s modulus as 31 GPa. Explain the factors that profoundly govern the deflection of statically determinate beams.
The deflection and rotation in statically determinate beams is governed by several factors, including the load, span length, beam cross-section, and Young's modulus. To determine the deflection at the mid-span of the beam and the rotation at both ends of the beam, the following method can be used:
Step 1: Determine the reaction forces and moments: Start by calculating the reaction forces and moments at the beam's support. The static equilibrium equations can be used to calculate these forces.
Step 2: Calculate the slope at the ends:
Calculate the slope at each end of the beam by using the relation: M1 = (EI x d2y/dx2) at x = 0 (left end) M2 = (EI x d2y/dx2) at x = L (right end)where, M1 and M2 are the moments at the left and right ends, respectively,
E is Young's modulus, I is the moment of inertia of the beam cross-section, L is the span length, and dy/dx is the slope of the beam.
Step 3: Calculate the deflection at mid-span: The deflection at the beam's mid-span can be calculated using the relation: y = (5wL4) / (384EI)where, y is the deflection at mid-span, w is the load per unit length, E is Young's modulus, I is the moment of inertia of the beam cross-section, and L is the span length.
Factors that govern the deflection of statically determinate beams. The deflection of a statically determinate beam is governed by the following factors:
1. Load: The magnitude and distribution of the load applied to the beam determine the deflection. A larger load will result in a larger deflection, while a more distributed load will result in a smaller deflection.
2. Span length: The longer the span, the greater the deflection. This is because longer spans are more flexible than shorter ones.
3. Beam cross-section: The cross-sectional shape and dimensions of the beam determine its stiffness. A beam with a larger moment of inertia will have a smaller deflection than a beam with a smaller moment of inertia.
4. Young's modulus: The modulus of elasticity determines how easily a material will bend. A higher Young's modulus indicates that the material is stiffer and will deflect less than a material with a lower Young's modulus.
Learn more about Young's modulus:
https://brainly.com/question/13257353
#SPJ11
An engine lathe is used to turn a cylindrical work part 125 mm in diameter by 400 mm long. After one pass of turn, the part is turned to be a diameter of 119mm with a cutting speed = 2.50 m/s and feed = 0.40 mm/rev. Determine the cutting time in seconds.
The cutting time in seconds is 400.
To determine the cutting time for the given scenario, we need to calculate the amount of material that needs to be removed and then divide it by the feed rate.
The cutting time can be found using the formula:
Cutting time = Length of cut / Feed rate
Given that the work part was initially 125 mm in diameter and was turned to a diameter of 119 mm in one pass, we can calculate the amount of material removed as follows:
Material removed = (Initial diameter - Final diameter) / 2
= (125 mm - 119 mm) / 2
= 6 mm / 2
= 3 mm
Now, let's calculate the cutting time:
Cutting time = Length of cut / Feed rate
= 400 mm / (0.40 mm/rev)
= 1000 rev
The feed rate is given in mm/rev, so we need to convert the length of the cut to revolutions by dividing it by the feed rate. In this case, the feed rate is 0.40 mm/rev.
Finally, to convert the revolutions to seconds, we need to divide by the cutting speed:
Cutting time = 1000 rev / (2.50 m/s)
= 400 seconds
Therefore, the cutting time for the given scenario is 400 seconds.
For more such questions on cutting,click on
https://brainly.com/question/12950264
#SPJ8
In a health examination survey of a prefecture in Japan, the population was found to have an average fasting blood glucose level of 99.0 with a standard deviation of 12 (normally distributed). What is thie probability that an individual selected at random will have a blood sugar level reading between 80 & 110? a 0.7641 b 0.6147 c 0.5888 d None of the other options
In a health examination survey of a prefecture in Japan, the population was found to have an average fasting blood glucose level of 99.0 with a standard deviation of 12 (normally distributed).
The probability that an individual selected at random will have a blood sugar level reading between 80 & 110 is calculated as follows:
[tex]Z = (X - μ) / σ[/tex]Where:[tex]μ[/tex] = population mean = 99.0
standard deviation = [tex]12X1 = 80X2 = 110Z1 = (80 - 99) / 12 = -1.583Z2 = (110 - 99) / 12 = 0.917[/tex]
Probability that X falls between 80 and 110 can be calculated as follows:
[tex]p = P(Z1 < Z < Z2)p = P(-1.583 < Z < 0.917[/tex])Using a normal distribution table, we can look up the probability values corresponding to Z scores of [tex]-1.583 and 0.917.p[/tex] =[tex]P(Z < 0.917) - P(Z < -1.583)p = 0.8212 - 0.0571p = 0.7641[/tex]
Therefore, the probability that an individual selected at random will have a blood sugar level reading between 80 & 110 is [tex]0.7641[/tex].
To know more about standard deviation visit:-
https://brainly.com/question/29115611
#SPJ11
Briefly explain how the resources in a GAL architecture can be used to implement a FSM. 2. (3 points) Repeat question 1 for a FPGA 3. (2 point) Theoretically, what size is the largest modulo-n counter that you can build in a Spartan XCS30XL FPGA?
Since the Spartan XCS30XL FPGA contains n flip-flops, the largest modulo-n counter that can be built is n bits long.
1. GAL is an acronym for a generic array logic device which is an improvement over the earlier PALs (programmable array logic). In a GAL architecture, an FSM (finite state machine) can be implemented using the following resources:
i. AND-OR gates: The AND-OR gates are used to implement the logic functions that define the state transitions of the FSM.
ii. JK flip-flops: These flip-flops are used as the storage elements to hold the present state of the FSM.
2. FPGA is an acronym for field-programmable gate array, which is an integrated circuit that can be programmed after being manufactured. In an FPGA, an FSM can be implemented using the following resources:
i. Look-up tables (LUTs): The LUTs can be used to implement the logic functions that define the state transitions of the FSM.
ii. Flip-flops: These flip-flops are used as the storage elements to hold the present state of the FSM.
3. The largest modulo-n counter that can be built in a Spartan XCS30XL FPGA theoretically is n bits. This is because a modulo-n counter requires n flip-flops to store the n states that the counter can take on.
Since the Spartan XCS30XL FPGA contains n flip-flops, the largest modulo-n counter that can be built is n bits long.
To know more about FPGA visit:
https://brainly.com/question/30434774
#SPJ11
A closed-loop system is analyzed. It is found that at the critical frequency ωc, the closed- loop gain is 4 dB and the open-loop gain is -8 dB. Which of the response is correct? O. We cannot conclude about the system stability. O. The system is stable. O. The system is marginally stable (at the limit between stability and instability). O. The system is unstable.
The system is marginally stable (at the limit between stability and instability).
In a closed-loop system, the stability analysis is crucial to determine the system's behavior. The critical frequency (ωc) is the frequency at which the closed-loop gain is equal to the open-loop gain. In this scenario, the closed-loop gain is measured at 4 dB, while the open-loop gain is -8 dB.
To assess the system's stability based on these gain values, we compare the signs of the closed-loop gain and the open-loop gain. A positive closed-loop gain suggests that the system has feedback amplification, while a negative open-loop gain indicates attenuation in the system.
Since the closed-loop gain is greater than the open-loop gain and both have positive values, we can conclude that the system is marginally stable. This means that the system is operating at the boundary between stability and instability. Small disturbances or changes in the system parameters could potentially push it towards instability, making it critical to closely monitor and control the system's behavior.
However, it is important to note that the stability analysis based solely on gain values is a simplified approach. Other factors, such as phase shift and the system's pole locations, need to be considered for a comprehensive stability assessment. Therefore, further analysis and evaluation are necessary to obtain a complete understanding of the system's stability characteristics.
To learn more about stability click here
brainly.com/question/32412546
#SPJ11
Learning Goal: Part A - Moment about the x axis at A A solid rod has a diameter of e=60 mm and is subjected to the loading shown. Let a=180 mm,b=200 mm,c= 350 mm,d=250 mm, and P=5.0kN. Take point A to Part B - Moment about the z axis at A be at the top of the circular cross-section.
The moment about the x-axis at A is 2.175 kN*m. The moment about the x-axis at A in the given diagram can be calculated.
Firstly, we need to calculate the magnitude of the vertical component of the force acting at point A; i.e., the y-component of the force. Since the rod is symmetric, the net y-component of the forces acting on it should be zero.The force acting on the rod at point C can be split into its horizontal and vertical components. The horizontal component can be found as follows:F_Cx = P cos 60° = 0.5 P = 2.5 kNThe vertical component can be found as follows:F_Cy = P sin 60° = 0.87 P = 4.35 kNThe force acting on the rod at point D can be split into its horizontal and vertical components. The horizontal component can be found as follows:F_Dx = P cos 60° = 0.5 P = 2.5 kNThe vertical component can be found as follows:F_Dy = P sin 60° = 0.87 P = 4.35 kNThe net y-component of the forces acting on the rod can now be calculated:F_y = F_Cy + F_Dy = 4.35 + 4.35 = 8.7 kNWe can now calculate the moment about the x-axis at A as follows:M_Ax = F_y * d = 8.7 * 0.25 = 2.175 kN*mTherefore, the moment about the x-axis at A is 2.175 kN*m. Answer: 2.175 kN*m.
Learn more about forces :
https://brainly.com/question/13191643
#SPJ11
The minimum pressure on an object moving horizontally in water (Ttemperatu at10 degree centrigrade) at (x+5) mm/s (where x is the last two digits of your student 10) at a depth of 1 m is 80 kPa (absolute). Calculate the velocity that will initiate cavitation. Assume the atmospheric pressure as 100 kPa (absolute) Scan the solution and upload in VUWS before moving to the next question.
Given data: Minimum pressure on an object = 80 kPa (absolute)Velocity of an object = (x+5) mm/sDepth of an object = 1mTemperature = 10°CAtmospheric pressure = 100 kPa (absolute)
We know that the minimum pressure to initiate cavitation is given as:pc = pa - (pv)²/(2ρ)Where, pa = Atmospheric pressurepv = Vapour pressure of liquidρ = Density of liquidNow, the vapour pressure of water at 10°C is 1.223 kPa (absolute) and density of water at this temperature is 999.7 kg/m³.Substituting the values in the above equation, we get:80 = 100 - (pv)²/(2×999.7) => (pv)² = 39.706
Now, the velocity that will initiate cavitation is given as:pv = 0.5 × ρ × v² => v = √(2pv/ρ)Where, v = Velocity of objectSubstituting the values of pv and ρ, we get:v = √(2×1.223/999.7) => v = 1.110 m/sTherefore, the velocity that will initiate cavitation is 1.110 m/s.
To know more about Velocity visit:-
https://brainly.com/question/18084516
#SPJ11
A heavy particle M moves up a rough surface of inclination a = 30 to the horizontal. Initially the velocity of the particle is v₀ = 15 m/s. The coefficient of friction is f = 0.1. Determine the distance travelled by the particle before it comes to rest and the time taken.
The distance travelled by the particle before it comes to rest is 284.9 m and the time taken is 19 s.
Given,
- Mass of the particle, `M` = heavy particle (not specified), assumed to be 1 kg
- Inclination of the surface, `a` = 30°
- Initial velocity of the particle, `v₀` = 15 m/s
- Coefficient of friction, `f` = 0.1
Here, the force acting along the incline is `F = Mgsin(a)` where `g` is the acceleration due to gravity. The force of friction opposing the motion is `fF⋅cos(a)`. From Newton's second law, we know that `F - fF⋅cos(a) = Ma`, where `Ma` is the acceleration along the incline.
Substituting the values given, we get,
`F = Mg*sin(a) = 1 * 9.8 * sin(30°) = 4.9 N`
`fF⋅cos(a) = 0.1 * 4.9 * cos(30°) = 0.42 N`
So, `Ma = 4.48 N`
Using the motion equation `v² = u² + 2as`, where `u` is the initial velocity, `v` is the final velocity (0 in this case), `a` is the acceleration and `s` is the distance travelled, we can calculate the distance travelled by the particle before it comes to rest.
`0² = 15² + 2(4.48)s`
`s = 284.9 m`
The time taken can be calculated using the equation `v = u + at`, where `u` is the initial velocity, `a` is the acceleration and `t` is the time taken.
0 = 15 + 4.48t
t = 19 s
The distance travelled by the particle before it comes to rest is 284.9 m and the time taken is 19 s.
To know more about distance, visit:
https://brainly.com/question/26550516
#SPJ11
A tank contains 1.6 kmol of a gas mixture with a gravimetric composition of 40% methane, 20% hydrogen, and the remainder is carbon monoxide. What is the mass of carbon monoxide in the mixture? Express your answer in kg.
Therefore, the mass of carbon monoxide in the gas mixture is approximately 17.92 kg.
What is the relationship between the boiling point and the intermolecular forces of a substance?To determine the mass of carbon monoxide in the gas mixture, we need to calculate the number of moles of carbon monoxide first.
The total number of moles in the mixture is given as 1.6 kmol. From the gravimetric composition, we know that methane constitutes 40% and hydrogen constitutes 20% of the mixture.
Therefore, the remaining percentage, which is 40%, represents the fraction of carbon monoxide in the mixture.
To calculate the number of moles of carbon monoxide, we multiply the total number of moles by the fraction of carbon monoxide:
Number of moles of carbon monoxide = 1.6 kmol ˣ 40% = 0.64 kmol
Next, we need to convert the moles of carbon monoxide to its mass. The molar mass of carbon monoxide (CO) is approximately 28.01 g/mol.
Mass of carbon monoxide = Number of moles ˣ Molar mass
Mass of carbon monoxide = 0.64 kmol ˣ 28.01 g/mol
Finally, we can convert the mass from grams to kilograms:
Mass of carbon monoxide = 0.64 kmol ˣ 28.01 g/mol / 1000 = 17.92 kg
Learn more about carbon monoxide
brainly.com/question/10193078
#SPJ11
The following state of strain has been determined on the surface of a machine part subjected to plane strain using a 600 strain rosette, where E= 210 GPa and ν= 0.3. = −90 = −360 c = +170 Determine: (a) The normal strains (εx, εy) and the shear strain γxy. (3 marks) (b) The normal strain (εn) and the shear strain (γxy) on an inclined plane that is oriented 30o counterclokwise from the x-axis. (4 marks) (c) The principal strains (εp1, εp2, εp3) and the maximum shear strain (γmax). (4 marks) (d) The normal stresses (, ) and shear stress () in a plane oriented at 30o counterclokwise from the x axis. (4 marks)
Given the information:
E = 210 GPa
v = 0.3
The normal strain (ε) is given by:
[tex]εx = 1/E (σx – vσy) + 1/E √(σx – vσy)² + σy² + 1/E √(σx – vσy)² + σy² – 2σxγxy + 1/E √(σx – vσy)² + σy² – 2σyγxy[/tex]
[tex]εy = 1/E (σy – vσx) + 1/E √(σx – vσy)² + σy² + 1/E √(σx – vσy)² + σy² + 2σxγxy + 1/E √(σx – vσy)² + σy² – 2σyγxy[/tex]
[tex]γxy = 1/(2E) [(σx – vσy) + √(σx – vσy)² + 4γ²xy][/tex]
Substituting the given values:
σx = -90 MPa, σy = -360 MPa, γxy = 170 MPa
Normal strains are:
εx = [tex]1/(210000) (-90 – 0.3(-360)) + 1/(210000) √((-90 – 0.3(-360))² + (-360)²) + 1/(210000) √((-90 – 0.3(-360))²[/tex]+
[tex]εx ≈ 0.0013888889[/tex]
[tex]εy ≈ -0.0027777778[/tex]
Shear strain [tex]γxy = 1/(2(210000)) [(-90) – 0.3(-360) + √((-90) – 0.3(-360))² + 4(170)²][/tex]
[tex]γxy ≈ 0.0017065709[/tex]
Normal stress is given by:
[tex]σx = σn/ cos²θ + τncosθsinθ + τnsin²θ[/tex]
[tex]σy = σn/ sin²θ – τncosθsinθ + τnsin²θ[/tex]
Substituting the given values:
[tex]θ = 30°[/tex]
[tex]σn = σx cos²θ + σy sin²θ + 2τxysinθcosθ[/tex]
[tex]σn = (-90)cos²30° + (-360)sin²30° + 2(170)sin30°cos30°[/tex]
[tex]σn = -235.34[/tex] MPa
[tex]τxy = [(σy – σx)/2] sin2θ + τxycos²θ – τn sin²θ[/tex]
[tex]τxy = [(360 – (-90))/2] sin60[/tex]
To know more about Substituting visit:
https://brainly.com/question/29383142
#SPJ11
1- Write about daily, monthly, and yearly loads.
2- Why generated power at electrical stations must equal load power (consumed power).
3- What is " based load", "intermediate load" and "peak load", draw.
4- Why electrical station are built far from cities?
5- On which principles the location of electrical stations is selected.
6- Why mainly A/C synchronous generators are used to generate electrical energy.
7- Why we use high voltage for transmission lines.
8- Compare between A/C and DC transmission lines.
9- What do we mean by "synchronized system"?
10- What is the role of the "preheater" in electrical stations?
11- Why we use low, medium and high-pressure turbines in electrical stations.
12- Discuss electrical stations efficiencies. and losses in electrical stations.
Daily, monthly, as well as yearly loads connote to the extent of electrical power that is taken in by a system or a region over different time frame.
What is load",Daily load means how much electricity is being used at different times of the day, over a 24-hour period. Usually, people use more electricity in the morning and evening when they use appliances and lights.
Monthly load means the total amount of electricity used in a month. This considers changes in how much energy is used each day and includes things like weather, seasons, and how people typically use energy.
Yearly load means the amount of energy used in a whole year. This looks at how much energy people use each month and helps companies plan how much energy they need to make and deliver over a long time.
Read more about based load here:
https://brainly.com/question/1288780
#SPJ4
A sensitive instrument of mass 100 kg is installed at a location that is subjected to harmonic motion with frequency 20 Hz and acceleration 0.5 m/s². If the instrument is supported on an isolator having a stiffness k = 25x104 N/m and a damping ratio & = 0.05, determine the maximum acceleration experienced by the instrument.
The maximum acceleration experienced by the instrument subjected to harmonic motion can be determined using the given frequency, acceleration, and the properties of the isolator, including stiffness and damping ratio.
The maximum acceleration experienced by the instrument can be calculated using the equation for the response of a single-degree-of-freedom system subjected to harmonic excitation:
amax = (ω2 / g) * A
where amax is the maximum acceleration, ω is the angular frequency (2πf), g is the acceleration due to gravity, and A is the amplitude of the excitation.
In this case, the angular frequency ω can be calculated as ω = 2πf = 2π * 20 Hz = 40π rad/s.
Using the given acceleration of 0.5 m/s², the amplitude A can be calculated as A = a / ω² = 0.5 / (40π)² ≈ 0.000199 m.
Now, we can calculate the maximum acceleration:
amax = (40π² / 9.81) * 0.000199 ≈ 0.806 m/s²
Therefore, the maximum acceleration experienced by the instrument is approximately 0.806 m/s².
Learn more about maximum acceleration here:
https://brainly.com/question/30703881
#SPJ11
Three identical capacitors of 15 micro farad are connected in star across a 415 volts, 50Hz 3-phase supply. What value of capacitance must be connected in delta to take the same line current and line voltage? Phase current in star Phase current in delta Value of Xc in delta Capacitance in delta
To achieve the same line current and line voltage as in the star connection with three identical capacitors of 15 microfarads. This ensures that the phase current in the delta connection matches the line current in the star connection.
To find the value of capacitance that must be connected in delta to achieve the same line current and line voltage as in the star connection, we can use the following formulas and relationships:
1. Line current in a star connection (I_star):
I_star = √3 * Phase current in star connection
2. Line current in a delta connection (I_delta):
I_delta = Phase current in delta connection
3. Relationship between line current and capacitance:
Line current (I) = Voltage (V) / Xc
4. Capacitive reactance (Xc):
Xc = 1 / (2πfC)
Where:
- f is the frequency (50 Hz)
- C is the capacitance
- Capacitance of each capacitor in the star connection (C_star) = 15 microfarad
- Voltage in the star connection (V_star) = 415 volts
Now let's calculate the required values step by step:
Step 1: Find the phase current in the star connection (I_star):
I_star = √3 * Phase current in star connection
Step 2: Find the line current in the star connection (I_line_star):
I_line_star = I_star
Step 3: Calculate the capacitive reactance in the star connection (Xc_star):
Xc_star = 1 / (2πfC_star)
Step 4: Calculate the line current in the star connection (I_line_star):
I_line_star = V_star / Xc_star
Step 5: Calculate the phase current in the delta connection (I_delta):
I_delta = I_line_star
Step 6: Find the value of capacitance in the delta connection (C_delta):
Xc_delta = V_star / (2πfI_delta)
C_delta = 1 / (2πfXc_delta)
Now let's substitute the given values into these formulas and calculate the results:
Step 1:
I_star = √3 * Phase current in star connection
Step 2:
I_line_star = I_star
Step 3:
Xc_star = 1 / (2πfC_star)
Step 4:
I_line_star = V_star / Xc_star
Step 5:
I_delta = I_line_star
Step 6:
Xc_delta = V_star / (2πfI_delta)
C_delta = 1 / (2πfXc_delta)
In a star connection, the line current is √3 times the phase current. In a delta connection, the line current is equal to the phase current. We can use this relationship to find the line current in the star connection and then use it to determine the phase current in the delta connection.
The capacitance in the star connection is given as 15 microfarads for each capacitor. Using the formula for capacitive reactance, we can calculate the capacitive reactance in the star connection.
We then use the formula for line current (I = V / Xc) to find the line current in the star connection. The line current in the star connection is the same as the phase current in the delta connection. Therefore, we can directly use this value as the phase current in the delta connection.
Finally, we calculate the value of capacitive reactance in the delta connection using the line current in the star connection and the formula Xc = V / (2πfI). From this, we can determine the required capacitance in the delta connection.
To read more about microfarads, visit:
https://brainly.com/question/32421296
#SPJ11
b) Determine the 4-point Discrete Fourier Transform (DFT) of the below function: x(n)={ 0
1
(n=0,3)
(n=1,2)
Find the magnitude of the DFT spectrum, and sketch the result. (10 marks)
The correct answer is "The 4-point DFT of the given function is x(0)=2, x(1)=0, x(2)=0, and x(3)=0. The magnitude of the DFT spectrum is 2, 0, 0, 0. The graph of the magnitude of the DFT spectrum is as shown above."
The given function is;x(n)={ 0 1
(n=0,3)
(n=1,2)
The formula for Discrete Fourier Transform (DFT) is given by;
x(k)=∑n
=0N−1x(n)e−i2πkn/N
Where;
N is the number of sample points,
k is the frequency point,
x(n) is the discrete-time signal, and
e^(-i2πkn/N) is the complex sinusoidal component which rotates once for every N samples.
Substituting the given values in the above formula, we get the 4-point DFT as follows;
x(0) = 0+1+0+1
=2
x(1) = 0+j-0-j
=0
x(2) = 0+1-0+(-1)
= 0
x(3) = 0-j-0+j
= 0
The DFT spectrum for 4-point DFT is given as;
x(k)=∑n
=0
N−1x(n)e−i2πkn/N
So, x(0)=2,
x(1)=0,
x(2)=0, and
x(3)=0
As we know that the magnitude of a complex number x is given by
|x| = sqrt(Re(x)^2 + Im(x)^2)
So, the magnitude of the DFT spectrum is given as;
|x(0)| = |2|
= 2|
x(1)| = |0|
= 0
|x(2)| = |0|
= 0
|x(3)| = |0| = 0
Hence, the magnitude of the DFT spectrum is 2, 0, 0, 0 as we calculated above. Also, the graph of the magnitude of the DFT spectrum is as follows:
Therefore, the correct answer is "The 4-point DFT of the given function is x(0)=2, x(1)=0, x(2)=0, and x(3)=0. The magnitude of the DFT spectrum is 2, 0, 0, 0. The graph of the magnitude of the DFT spectrum is as shown above."
To know more about DFT spectrum visit:
https://brainly.com/question/32065478
#SPJ11
A piston-cylinder device contains 0.005 m3 of liquid water and 0.95 m3 of water vapor in equilibrium at 600 kPa. Heat is transferred at constant pressure until the temperature reaches 200°C. Using appropriate software, investigate the effect of pressure on the total mass of water in the tank. Let the pressure vary from 0.1 MPa to 1 MPa. Plot the total mass of water against pressure, and discuss the results. Also, show the process on a P-V diagram using the property plot feature of the software. Solve this problem using the appropriate software. Use data from the tables. Please upload your response/solution by using the controls provided below.
The total mass of water in the tank decreases as the pressure increases from 0.1 MPa to 1 MPa.
As the pressure increases, the water vapor in the piston-cylinder device undergoes compression, causing a decrease in its volume. This decrease in volume leads to a decrease in the amount of water vapor present in the system. Since the water and water vapor are in equilibrium, a decrease in the amount of water vapor also results in a decrease in the amount of liquid water.
At lower pressures, there is a larger amount of water vapor in the system, and as the pressure increases, the vapor condenses into liquid water. Therefore, as the pressure increases from 0.1 MPa to 1 MPa, the total mass of water in the tank decreases.
Learn more about Total mass
brainly.com/question/15582690
#SPJ11
Select all items below which are crucial in lost-foam casting.
(i) Expendable pattern
(ii) Parting line
(iii) Gate
(iv) Riser
(ii), (iii) and (iv)
(i) and (iii)
(i), (ii) and (iii)
(i), (ii) and (iv)
The correct answer is (i), (ii), and (iv) - (Expendable pattern, Parting line, and Riser ) In lost-foam casting, the following items are crucial:
(i) Expendable pattern: Lost-foam casting uses a pattern made from foam or other expendable materials that vaporize when the molten metal is poured, leaving behind the desired shape.
(ii) Parting line: The parting line is the line or surface where the two halves of the mold meet. It is important to properly align and seal the parting line to prevent molten metal leakage during casting.
(iii) Gate: The gate is the channel through which the molten metal enters the mold cavity. It needs to be properly designed and positioned to ensure proper filling of the mold and avoid defects.
(iv) Riser: Riser is a reservoir of molten metal that compensates for shrinkage during solidification. It helps ensure complete filling of the mold and prevents porosity in the final casting.
Therefore, the correct answer is (i), (ii), and (iv) - (Expendable pattern, Parting line, and Riser)
For more information on Lost-foam visit https://brainly.com/question/33282866
#SPJ11
The grinder has a force of 400 N in the direction shown at the bottom. The grinder has a mass of 300 kg with center of mass at G. The wheel at B is free to move (no friction). Determine the force in the hydraulic cylinder DF. Express in newtons below.
The resultant force in the hydraulic cylinder DF can be determined by considering the equilibrium of forces and moments acting on the grinder.
A detailed explanation requires a clear understanding of the principles of statics and dynamics. First, we need to identify all forces acting on the grinder: gravitational force, which is the product of mass and acceleration due to gravity (300 kg * 9.8 m/s^2), force due to the grinder (400 N), and force in the hydraulic cylinder DF. Assuming the system is in equilibrium (i.e., sum of all forces and moments equals zero), we can create equations based on the force equilibrium in vertical and horizontal directions and the moment equilibrium around a suitable point, typically point G. Solving these equations gives us the force in the hydraulic cylinder DF.
Learn more about static equilibrium here:
https://brainly.com/question/25139179
#SPJ11
Determine the design heating load for a residence, 30 by 100 by 10 ft (height), to be located in Windsor Locks, Connecticut (design indoor temperature is 72 F and 30% RH and outdoor temperature is 3 F and 100% RH), which has an uninsulated slab on grade concrete floor (F-0.84 Btu/ft). The construction consists of Walls: 4 in. face brick (R=0.17), % in plywood sheathing (R=0.93), 4 in. cellular glass insulation (R=12.12), and / in. plasterboard (R=0.45) Ceiling/roof: 3 in. lightweight concrete deck (R=0.42), built-up roofing (R=0.33), 2 in. of rigid, expanded rubber insulation (R=9.10), and a drop ceiling of 7 in, acoustical tiles (R=1.25), air gap between rubber insulation and acoustical tiles (R=1.22) Windows: 45% of each wall is double pane, nonoperable, metal-framed glass with 1/4 in, air gap (U-0.69) Doors: Two 3 ft by 7 A, 1.75 in. thick, solid wood doors are located in each wall (U-0.46) All R values are in hr ft F/Btu and U values are in Btu/hr ft F units. R=1/U.
Design Heating Load Calculation for a residence located in Windsor Locks, Connecticut with an uninsulated slab on grade concrete floor and different construction materials is given below: The heating load is calculated by using the formula:
Heating Load = U × A × ΔTWhere,U = U-value of wall, roof, windows, doors etc.A = Total area of the building, walls, windows, roof and doors, etc.ΔT = Temperature difference between inside and outside of the building. And a drop ceiling of 7 in,
acoustical tiles (R = 1.25)Air gap between rubber insulation and acoustical tiles (R = 1.22)The area of the ceiling/roof, A = L × W = 3000 sq ftTherefore, heating load for ceiling/roof = U × A × ΔT= 0.0813 × 3000 × (72 - 3)= 17973 BTU/hrWalls:4 in.
face brick (R = 0.17)0.5 in. plywood sheathing (R = 0.93)4 in. cellular glass insulation (R = 12.12)And 0.625 in. Therefore, heating load for walls = U × A × ΔT= 0.0731 × 5830 × (72 - 3)= 24315 BTU/hrWindows:
45% of each wall is double pane, nonoperable, metal-framed glass with 1/4 in. air gap (U = 0.69)Therefore, heating load for doors = U × A × ΔT= 0.46 × 196 × (72 - 3)= 4047 BTU/hrFloor:
To know more about Calculation visit:
https://brainly.com/question/30781060
#SPJ11
On the basis of past experience, the probability that a certain electrical component will be satisfactory is 0.98. The components are sampled item by item from continuous production. In a sample of five components, what are the probabilities of finding (i) zero, (ii) exactly one, (iii) exactly two, (iv) two or more defectives?
The probability of an electrical component to be satisfactory is 0.98. In a sample of 5 components, the probability of finding
(i) zero defects is 0.000032,
(ii) exactly one defective is 0.00154,
(iii) exactly two defectives is 0.0293,
(iv) two or more defectives is 0.0313.
Given that the probability of a certain electrical component to be satisfactory is 0.98. The components are sampled item by item from continuous production. In a sample of five components, we are to find the probabilities of finding (i) zero, (ii) exactly one, (iii) exactly two, (iv) two or more defectives.
Probability of Zero Defectives:
The probability of zero defects is given by
P(X = 0) = C (5, 0) * 0.98^5 * 0^0 = 0.98^5.
Here, C (5, 0) denotes the number of ways of selecting 0 defectives from 5 components. Therefore, the probability of zero defects is P(X = 0) = 0.000032.
Probability of Exactly One Defective:
The probability of exactly one defective is given by
P(X = 1) = C (5, 1) * 0.98^4 * 0^1 = 0.98^4 * 0.02 * 5.
Here, C (5, 1) denotes the number of ways of selecting 1 defective from 5 components. Therefore, the probability of exactly one defective is P(X = 1) = 0.00154.
Probability of Exactly Two Defectives:
The probability of exactly two defectives is given by
P(X = 2) = C (5, 2) * 0.98^3 * 0^2 = 0.98^3 * 0.02^2 * 10.
Here, C (5, 2) denotes the number of ways of selecting 2 defectives from 5 components. Therefore, the probability of exactly two defectives is P(X = 2) = 0.0293.
Probability of Two or More Defectives:
The probability of two or more defectives is given by
P(X ≥ 2) = 1 - P(X < 2) = 1 - P(X = 0) - P(X = 1) = 1 - 0.000032 - 0.00154 = 0.9984.
Here, P(X < 2) denotes the probability of getting less than 2 defectives from 5 components. Therefore, the probability of two or more defectives is P(X ≥ 2) = 0.0313.
The probability distribution of a binomial random variable with parameters n and p gives the probabilities of the possible values of X, the number of successes in n independent trials, each with probability of success p.
Here, n = 5 and p = 0.98.
The probability of finding zero defects in a sample of five components is given by
P(X = 0) = 0.98^5 = 0.000032.
The probability of finding exactly one defective is given by
P(X = 1) = 0.02 * 0.98^4 * 5 = 0.00154.
The probability of finding exactly two defectives is given by
P(X = 2) = 0.02^2 * 0.98^3 * 10 = 0.0293.
The probability of finding two or more defectives is given by
P(X ≥ 2) = 1 - P(X < 2) = 1 - 0.000032 - 0.00154 = 0.9984.
Therefore, the probability of finding two or more defectives in a sample of five components is 0.0313.
To learn more about probability
https://brainly.com/question/16988487
#SPJ11
Steam at 20 bar, 360 C is expanded in a steam turbine to 0.08 bar. It then enters a condenser, where it is condensed to saturated liquid water. The pump feeds back the water into the boiler. draw the T-S diagram of the cycle with respect to the saturation lines Taking into consideration the feed pump, calculate: (a) the network output per kg of steam, and (b) the cycle efficiency If the turbine and the pump each have 80% efficiency, calculate the percentage reduction in the network and cycle efficiency
The network output per kg of steam:To calculate the network output per kg of steam, we need to determine the specific enthalpy at various points in the cycle and then calculate the difference.
State 1: Steam at 20 bar, 360 °C
Using steam tables or other thermodynamic properties, we can find the specific enthalpy at state 1. Let's denote it as h1.
State 2: Steam expanded to 0.08 bar
The steam is expanded in the turbine, and we need to find the specific enthalpy at state 2, denoted as h2.
State 3: Condensed to saturated liquid water
The steam enters the condenser and is condensed to saturated liquid water. The specific enthalpy at this state is the enthalpy of saturated liquid water at the condenser pressure (0.08 bar). Let's denote it as h3.
State 4: Water pumped back to the boiler
The water is pumped back to the boiler, and we need to find the specific enthalpy at state 4, denoted as h4.
Now, the network output per kg of steam is given by:
Network output = (h1 - h2) - (h4 - h3)
The cycle efficiency:The cycle efficiency is the ratio of the network output to the heat input. Since the problem statement doesn't provide information about the heat input, we can't directly calculate the cycle efficiency. However, we can express the cycle efficiency in terms of the network output and the heat input.
Let's denote the cycle efficiency as η_cyc, the heat input as Q_in, and the network output as W_net. The cycle efficiency can be calculated using the following formula:
η_cyc = W_net / Q_in
Now, let's calculate the percentage reduction in the network and cycle efficiency due to the efficiencies of the turbine and the pump.
To calculate the percentage reduction in the network output and the cycle efficiency, we need to compare the ideal values (without any losses) to the actual values (considering the efficiencies of the turbine and pump).
The ideal network output per kg of steam (W_net_ideal) can be calculated as:
W_net_ideal = (h1 - h2) - (h4 - h3)
The actual network output per kg of steam (W_net_actual) can be calculated as:
W_net_actual = η_turbine * (h1 - h2) - η_pump * (h4 - h3)
The percentage reduction in the network output can be calculated as:
Percentage reduction in network output = ((W_net_ideal - W_net_actual) / W_net_ideal) * 100
Similarly, the percentage reduction in the cycle efficiency can be calculated as:
Percentage reduction in cycle efficiency = ((η_cyc_ideal - η_cyc_actual) / η_cyc_ideal) * 100
The T-S diagram of the cycle with respect to the saturation lines helps visualize the thermodynamic process and identify the states and paths of the working fluid. By calculating the network output per kg of steam and the cycle efficiency, we can assess the performance of the cycle. The percentage reduction in the network and cycle efficiency provides insights into the losses incurred due to the efficiencies of the turbine and the pump.
Learn more about enthalpy ,visit:
https://brainly.com/question/30464179
#SPJ11
A square key is to be used in 40 mm diameter shaft and that will developed a 2 KN-m torque. If bearing stress of the key is 400 Mpa, determine the cross sectional dimension of square key to be used if key length is 30 mm. Answer: D
A. 324.80 mm2
B. 246.80 mm2
C. 446.80 mm2
D. 277.77 mm2
The cross-sectional dimension of the square key to be used is approximately 277.77 mm². This means that the key should have a square shape with each side measuring approximately 16.68 mm (sqrt(277.77)).
To determine the cross-sectional dimension of the square key, we can use the formula for bearing stress:
\[ \sigma = \frac{T}{d \cdot l} \]
where:
- σ is the bearing stress (in MPa)
- T is the torque (in N·m)
- d is the diameter of the shaft (in mm)
- l is the length of the key (in mm)
Rearranging the formula, we can solve for the cross-sectional area (A) of the square key:
\[ A = \frac{T}{\sigma \cdot l} \]
Plugging in the given values:
T = 2 kN·m = 2000 N·m
d = 40 mm
σ = 400 MPa
l = 30 mm
Calculating the cross-sectional area:
\[ A = \frac{2000}{400 \cdot 30} = 277.77 mm².
Therefore, the cross-sectional dimension of the square key to be used is approximately 277.77 mm². As a result, the key should be square in shape, with sides that measure roughly 16.68 mm (sqrt(277.77)).
To know more about cross-sectional, visit:
https://brainly.com/question/15847581
#SPJ11
1. (20pts) Schedule 80 PVC pipe has an outside diameter of 1.900in and an inside diameter of 1.476in. PVC has a yield strength of 8ksi and an elastic modulus of 400ksi. You intend to make a "potato cannon." a. (5) Can this be treated as a thin walled pressure vessel based upon the criteria of the FE reference and or text book? b. (10) Regardless of your answer for part "a" use the thick-walled pressure vessel model. Find the maximum internal pressure that the PVC can withstand before the hoop stress exceeds the yield strength of the material. c. (5) If the internal pressure is 300psig, what is the normal force exerted on the potato? Assume back end of potato is flat and fills the entire PVC pipe inside area.
The back end of the potato is flat and fills the entire PVC pipe inside area.Substituting the given values in the equation, we get the value of Fn.Fn= p * A= 300 * π * (1.476/2)²= 535.84 lb.
a. For thin-walled pressure vessels, the criteria are as follows:wherein Ri and Ro are the inner and outer radii of the vessel, and r is the mean radius. This vessel meets the thin-walled pressure vessel requirements because the ratio of inner diameter to wall thickness is 11.6, which is higher than the criterion of 10.b. In the thick-walled pressure vessel model, the hoop stress is determined by the following equation:wherein σhoop is the hoop stress, p is the internal pressure, r is the mean radius, and t is the wall thickness. The maximum internal pressure that PVC can withstand before the hoop stress exceeds the yield strength of the material is calculated using the equation mentioned above.Substituting the given values in the equation, we get the value of p.σhoop
= pd/2tσhoop
= p * (1.9 + 1.476) / 2 / (1.9 - 1.476)
= 13.34psi.
The maximum internal pressure is 13.34psi.c. Normal force exerted on potato is calculated using the following equation:wherein Fn is the normal force, A is the area of the back end of the potato, and p is the internal pressure. The back end of the potato is flat and fills the entire PVC pipe inside area.Substituting the given values in the equation, we get the value of Fn.Fn
= p * A
= 300 * π * (1.476/2)²
= 535.84 lb.
To know more about Substituting visit:
https://brainly.com/question/29383142
#SPJ11
A steam power plant that produces 125,000 kw power has a turbo-generator with reheat-regenerative unit. The turbine operates steam with a condition of 92 bar, 440 C and a flow rate of 8,333.33 kg/min. Consider the cycle with 3 extraction on 23.5 bar, 17 bar and last extraction is saturated. The condenser has a measured temperature of 45C. Solve for
(a) engine thermal efficiency,
(b) cycle thermal efficiency,
(c) work of the engine,
(d) combined engine efficiency
(a) Engine thermal efficiency ≈ 1.87% (b) Cycle thermal efficiency ≈ 1.83% (c) Work of the engine ≈ 26,381,806.18 kJ/min (d) Combined engine efficiency ≈ 97.01%
To solve this problem, we’ll use the basic principles of thermodynamics and the given parameters for the steam power plant. We’ll calculate the required values step by step.
Given parameters:
Power output (P) = 125,000 kW
Turbine inlet conditions: Pressure (P₁) = 92 bar, Temperature (T₁) = 440 °C, Mass flow rate (m) = 8,333.33 kg/min
Extraction pressures: P₂ = 23.5 bar, P₃ = 17 bar
Condenser temperature (T₄) = 45 °C
Let’s calculate these values:
Step 1: Calculate the enthalpy at each state
Using the steam tables or software, we find the following approximate enthalpy values (in kJ/stat
H₁ = 3463.8
H₂ = 3223.2
H₃ = 2855.5
H₄ = 190.3
Step 2: Calculate the heat added in the boiler (Qin)
Qin = m(h₁ - h₄)
Qin = 8,333.33 * (3463.8 – 190.3)
Qin ≈ 27,177,607.51 kJ/min
Step 3: Calculate the heat extracted in each extraction process
Q₂ = m(h₁ - h₂)
Q₂ = 8,333.33 * (3463.8 – 3223.2)
Q₂ ≈ 200,971.48 kJ/min
Q₃ = m(h₂ - h₃)
Q₃ = 8,333.33 * (3223.2 – 2855.5)
Q₃ ≈ 306,456.43 kJ/min
Step 4: Calculate the work done by the turbine (Wturbine)
Wturbine = Q₂ + Q₃ + Qout
Wturbine = 200,971.48 + 306,456.43
Wturbine ≈ 507,427.91 kJ/min
Step 5: Calculate the heat rejected in the condenser (Qout)
Qout = m(h₃ - h₄)
Qout = 8,333.33 * (2855.5 – 190.3)
Qout ≈ 795,801.33 kJ/min
Step 6: Calculate the engine thermal efficiency (ηengine)
Ηengine = Wturbine / Qin
Ηengine = 507,427.91 / 27,177,607.51
Ηengine ≈ 0.0187 or 1.87%
Step 7: Calculate the cycle thermal efficiency (ηcycle)
Ηcycle = Wturbine / (Qin + Qout)
Ηcycle = 507,427.91 / (27,177,607.51 + 795,801.33)
Ηcycle ≈ 0.0183 or 1.83%
Step 8: Calculate the work of the engine (Wengine)
Wengine = Qin – Qout
Wengine = 27,177,607.51 – 795,801.33
Wengine ≈ 26,381,806.18 kJ/min
Step 9: Calculate the combined engine efficiency (ηcombined)
Ηcombined = Wengine / Qin
Ηcombined = 26,381,806.18 / 27,177,607.51
Ηcombined ≈ 0.9701 or 97.01%
Learn more about Engine thermal efficiency here: brainly.com/question/32492186
#SPJ11
An engineer is tasked with pumping oil (p = 870 kg/m) from a tank 2 m below the ground to a tank 35 m above the ground. Calculate the required pressure difference across the pump.
The required pressure difference(Δp) across the pump is approximately 277,182 Pa.
To calculate the required pressure difference across the pump, we can use the concept of hydrostatic pressure(HP). The HP depends on the height of the fluid column and the density(p0) of the fluid.
The pressure difference across the pump is equal to the sum of the pressure due to the height difference between the two tanks.
Given:
Density of oil (p) = 870 kg/m³
Height difference between the two tanks (h) = 35 m - 2 m = 33 m
The pressure difference (ΔP) across the pump can be calculated using the formula:
ΔP = ρ * g * h
where:
ρ is the density of the fluid (oil)
g is the acceleration due to gravity (approximately 9.8 m/s²)
h is the height difference between the two tanks
Substituting the given values:
ΔP = 870 kg/m³ * 9.8 m/s² * 33 m
ΔP = 277,182 Pa.
To know more about hydrostatic pressure visit:
https://brainly.com/question/33192185
#SPJ11