Answer:
Her speed at the bottom of the slide is 7.42 m/s
Explanation:
From the question,
The swimmer starts at rest, that is, her initial speed, u is 0 m/s.
Since she slides without friction and descends through a vertical height, then it is a free fall motion (due to gravity).
Also, from the question,
She descends through a vertical height of 2.81 m.
To determine her speed at the bottom of the slide, that is her final speed,
From one of the equations of motion for freely falling bodies
v² = u² + 2gh
Where v is the final speed
u is the initial speed
g is acceleration due to gravity (g = 9.8 m/s²)
and h is height
From the question,
u = 0 m/s
h = 2.81 m
Putting the values into the equation
v² = u² + 2gh
v² = 0² + 2×9.8×2.81
v² = 55.076
v =√55.076
v = 7.42 m/s
Hence, her speed at the bottom of the slide is 7.42 m/s.
Write a haiku
poem
explaining
why graphing
is useful.
If you are
able, share
your poem
with others.
Answer:
Explanation:
graphing is helpful
helps visualize the line
of your equation
I WILL MARK YOU AS BRAINLIEST IF RIGHT
What is the magnitude of the net force acting on this object? And what direction?
Answer:
The magnitude of the net force acting on an object is equal to the mass. and the direction is in 20N
Explanation:
A 10-ohm resistor has a constant current. If 1200 C of charge flow through it in 4 minutes what
is the value of the current?
A. 3.0 A
B 5.0 A
C. 11 A
D. 15 A
E. 20A
Answer:
B 5.0 A .
Explanation:
Hello.
In this case, since we know the charge (1200 C), time (4 min =240 s) and resistance (10Ω) which is actually not needed here, we compute the current as follows:
[tex]I=\frac{Q}{t}[/tex]
Then, for the given data, we obtain:
[tex]I=\frac{1200C}{4min}*\frac{1min}{60s}\\\\I=5A[/tex]
Therefore, answer is B 5.0 A .
Best regards!
A single-turn circular loop of radius 9.4 cm is to produce a field at its center that will just cancel the earth's field of magnitude 0.7 G directed at 70degrees below the horizontal north direction. Find the current in the loop.
Answer:
The current in the loop is 10.5 A.
Explanation:
Given that,
Radius = 9.4 cm
Magnetic field = 0.7 G
Angle = 70°
We know that,
The magnetic field due to the current in a loop is
[tex]B_{I}=\dfrac{\mu_{0}NI}{2r}[/tex]
The magnetic field due to the current is equal to the magnetic field of earth.
[tex]B_{E}=B_{I}=\dfrac{\mu_{0}NI}{2r}[/tex]
We need to calculate the current in the loop
Using formula of magnetic field
[tex]B=\dfrac{\mu_{0}NI}{2r}[/tex]
[tex]I=\dfrac{2rB}{\mu_{0}N}[/tex]
Put the value into the formula
[tex]I=\dfrac{2\times9.4\times10^{-2}\times0.7\times10^{-4}}{4\pi\times10^{-7}\times1}[/tex]
[tex]I=10.5\ A[/tex]
Hence, The current in the loop is 10.5 A.
If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in the above situation to be Imax
The complete question is;
A person with body resistance between his hands of 10 kΩ accidentally grasps the terminals of a 16-kV power supply. What is the power dissipated in his body?
A) If the internal resistance of the power supply is 1600 Ω , what is the current through the person's body?
B) What is the power dissipated in his body?
C) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in the above situation to be I_max = 1.00mA or less?
Answer:
A) I = 1.379 A
B) P = 19016.41 W
C) r = 15990000 Ω
Explanation:
A) We are given;
Internal resistance of the power supply; r = 1600 Ω
Body resistance between hands; R = 10kΩ = 10000 Ω
Power supply voltage; E =16 kV = 16000 V
Formula for the current through the person's body with internal resistance is given by;
I = E/(R + r)
Thus;
I = 16000/(10000 + 1600)
I = 1.379 A
B) Formula for power dissipated is;
P = I²R
P = 1.379² × 10000
P = 19016.41 W
C) Now, we are told that the maximum current should be I_max = 1.00mA or less. So, I_max = 0.001 A
Thus, from I = E/(R + r) and making r the subject, we have;
r = (E/I) - R
r = (16000/0.001) - 10000
r = 15990000 Ω
Chris races his Audi north down a road for 1000 meters in 20 seconds, what is his velocity?
Answer:
I think it would be 50 I am not really sure
Explanation:
I think you would have to divid 1000 by 20 Again I'm not sure
A cannonball is fired horizontally from a 10 m high cliff at 20 m/s. How long will the cannonball be in the air? How far away will the cannonball strike the ground?
Answe ¡Buenos días! –
#3 ¡Buenas tardes! –
#4 ¡Bienvenid
In a spy movie, the hero, James, stands on a scale that is positioned horizontally on the floor. It registers his weight as 810 N . Unknown to our hero, the floor is actually a trap door, and when the door suddenly disappears, James and the scale fall at the acceleration of gravity, down towards an unknown fate. As James falls, he looks at the scale to see his weight. What does he see
Answer:
His weight would be zero on the scale i.e he is weightless at that instance.
Explanation:
weight = mg
where m is the mass of the object, and g is the acceleration of gravity.
⇒ 810 = mg
During free fall, the weight of an object can be determined by:
W = mg - ma (provided that acceleration of gravity is greater than acceleration of the object)
where a is the acceleration of the object.
But since James fall at the acceleration of gravity, then:
g = a
mg = ma = 810 N
So that;
W = 810 - 810
= 0 N
Therefore though the weight of James is 810 N, but the scale reads 0 N. this condition is referred to as weightlessness.
The interaction between electrical energy and magnetism has been an important
topic in 20th century science, Which term describes this interaction?
Answer:
Maybe
Explanation:
I say maybe because it will help them still but not quite
Design a tension member and slip-critical splice to carry a factored load of 500 kips. Please use a wide-flange section for the tension member. Please use A572 Gr. 50 steel plates for the splice plates. Please use Group B, A490 bolts for the splice connection. The splice connection should be slip-critical, and have adequate strength after slip occurs as well. Please make any other assumptions you need in order to complete the problem. Provide detailed sketches and drawings for your design.
Answer:
Kindly check the explanation section.
Explanation:
For the design we are asked for in this question/problem there is the need for us to calculate or determine the strength in fracture and that of the yield. Also, we need to calculate for the block shear strength.
From the question, we have that the factored load = 500kips. Also, note that the tension splice must not slip.
Also, the shear force are resisted by friction, that is to say shear resistance = 1.13 × Tb × Ns.
Assuming our db = 3/4 inches, then the slip critical resistance to shear service load = 18ksi(refer to AISC manual for the table).
If db = 7/8 inches, then the shear force resistance for n bolt = 10.2kips, n > 49.6.
The yielding strength = 0.9 × Aj × Fhb= 736 kips > 500
The fracture strength = .75 × Ah × Fhb = 309 kips.
The bearing strength of 7/8 inches bolt at the edge hole and other holes = 46 kips and 102 kips.
What resistance must be connected in parallel with a 633-Ω resistor to produce an equivalent resistance of 205 Ω?
Answer:
303 Ω
Explanation:
Given
Represent the resistors with R1, R2 and RT
R1 = 633
RT = 205
Required
Determine R2
Since it's a parallel connection, it can be solved using.
1/Rt = 1/R1 + 1/R2
Substitute values for R1 and RT
1/205 = 1/633 + 1/R2
Collect Like Terms
1/R2 = 1/205 - 1/633
Take LCM
1/R2 = (633 - 205)/(205 * 633)
1/R2 = 428/129765
Take reciprocal of both sides
R2 = 129765/428
R2 = 303 --- approximated
the neuron is considered a (a. Cell. (B.artery. (C. Vein
Answer:
A Cell
Explanation:
The precision value of measuring tape is
1)0.1cm
2)0.1mm
3)1cm
4)0.01cm
C.1cm
Explanation:
precision is how close two or more measurements are to each other
4?
Explanation:
sorry im not sure but
You can always take a metre ruler as a starting point. Your metre ruler has the same precision as your 15.0cm or 30.0cm ruler, so bring a ruler during exams as they'll come in handy ;)
The order goes like this:
rulers: 0.1cm or 1mm
measuring tape: 0.01cm or 0.1mm
vernier calipers: 0.001cm or 0.01mm
micrometer screw gauge: 0.0001cm or 0.001mm
((if i'm not wrong))
A 1870 kg car traveling at 13.5 m/s collides with a 2970 kg car that is initally at rest at a stoplight. The cars stick together and move 1.93 m before friction causes them to stop. Determine the coefficient of kinetic friction between the cars and the road, assuming that the negative acceleration is constant and all wheels on both cars lock at the time of impact.
Answer:
The value is [tex] \mu = 0.72 [/tex]
Explanation:
From the question we are told that
The mass of the first car is [tex]m_1 = 1870\ kg[/tex]
the initial speed of the car is [tex]u = 13.5 \ m/s[/tex]
The mass of the second car is [tex]m_2 = 2970\ kg[/tex]
The distance move by both cars is s = 1.93 m
Generally from the law of momentum conservation
[tex]m_1 * u_1 + m_2 * u_2 = (m_1 + m_2 ) * v_f[/tex]
Here [tex]u_2 = 0[/tex] because the second car is at rest
and [tex]v_f[/tex] is the final velocity of the the two car
So
[tex]1870* 13.5+ 0= ( 1870 + 2970 ) * v_f[/tex]
=> [tex]v_f = 5.22\ m/s[/tex]
Generally from kinematic equation
[tex]v_f^2 = u_2^2 + 2as[/tex]
here a is the deceleration
So
[tex]5.22^2 = 0 + 2 *a * 1.93[/tex]
=> [tex]a = 7.06 \ m/s^2 [/tex]
Generally the frictional force is equal to the force propelling the car , this can be mathematically represented as
[tex]F_f = F[/tex]
Here F is mathematically represented as
[tex]F = (m_1 + m_2) * a[/tex]
[tex]F = (1870 + 2970) * 7.06 [/tex]
[tex]F =34170.4 \ N[/tex]
and
[tex]F_f = \mu * (m_1 + m_2 ) * g[/tex]
[tex]F_f = 47432 * \mu [/tex]
So
[tex] 47432 * \mu = 34170.4 [/tex]
=> [tex] 47432 * \mu = 34170.4 [/tex]
=> [tex] \mu = 0.72 [/tex]
A 849-kg car starts from rest on a horizontal roadway and accelerates eastward for 5.00 s when it reaches a speed of 35.0 m/s. What is the average force exerted on the car during this time
Answer:
The average force exerted on the car during this time is 5,943 N
Explanation:
Given;
mass of the car, m = 849 kg
initial velocity of the car, u = 0
time of motion of the car, t = 5.00 s
final velocity of the car, v = 35 m/s
The average force exerted on the car during this time is given by;
[tex]F = ma \\\\F = \frac{m(v-u)}{t}\\\\F = \frac{849(35-0)}{5}\\\\F = \frac{849(35)}{5}\\\\ F = 849*7\\\\F = 5,943 \ N[/tex]
Therefore, the average force exerted on the car during this time is 5,943 N
Answer:
5943N
Let's say (+x) = eastward
Average horizontal acceleration
ax = vx -v0x/5.00s
= 35.0m/s-0/5.00s
= +7.09m/s
From here we apply the second law of newton
During this period average horizontal force acting on car
Summation x = max = (849kg)(+7.09m/s²)
= 5943N
+5.943x10³N
= 5.94kN east ward.
You measure the radius of a sphere as (6.45 ± 0.30) cm, and you measure its mass as (1.79 ± 0.08) kg. What is the density and uncertainty in the density of the sphere, in kilograms per cubic meter?
Answer:
[tex](1630.13\pm 300.10)\ kg/m^3[/tex]
Explanation:
Given that,
The radius of a sphere is (6.45 ± 0.30) cm
Mass of the sphere is (1.79 ± 0.08) kg
Density = mass/volume
For sphere,
[tex]d=\dfrac{m}{V}\\\\d=\dfrac{m}{\dfrac{4}{3}\pi r^3}\\\\d=\dfrac{1.79\ kg}{\dfrac{4}{3}\pi (6.4\times 10^{-2}\ m)^3}\\\\d=1630.13\ kg/m^3[/tex]
We can find the uncertainty in volume as follows :
[tex]\dfrac{\delta V}{V}=3\dfrac{\delta r}{r}\\\\=3\times \dfrac{0.3\times 10^{-2}}{6.45\times 10^{-2}}\\\\=0.1395[/tex]
Uncertainty in mass,
[tex]\dfrac{\delta m}{m}=\dfrac{0.08}{1.79}\\\\=0.0446[/tex]
Now, the uncertainty in density of sphere is given by :
[tex]\dfrac{\delta d}{d}=\dfrac{\delta m}{m}+\dfrac{\delta V}V}\\\\=0.0446+0.1395\\\\\dfrac{\delta d}{d}=0.1841\\\\\delta d=0.1841\times d\\\\\delta d=0.1841\times 1630.13\\\\\delta d = 300.10\ kg/m^3[/tex]
Hence, the density pf the sphere is [tex](1630.13\pm 300.10)\ kg/m^3[/tex]
An object moving 20 m/s
experiences an acceleration of 4 m/s' for 8
seconds. How far did it move in that time?
Variables:
Equation and Solve:
Answer:
We are given:
initial velocity (u) = 20m/s
acceleration (a) = 4 m/s²
time (t) = 8 seconds
displacement (s) = s m
Solving for Displacement:
From the seconds equation of motion:
s = ut + 1/2 * at²
replacing the variables
s = 20(8) + 1/2 * (4)*(8)*(8)
s = 160 + 128
s = 288 m
A crane uses a single cable to lower a steel girder into place. The girder moves with constant speed. The cable tension does work WT and gravity does work WG. Which statement is true
Explanation:
Work done by a force is given by :
[tex]W=Fd\cos\theta[/tex]
Where
F is force, d is displacement and [tex]\theta[/tex] is the angle between F and d.
In this problem, a crane is moving in downward direction, the force gravity is in downward direction and the tension is in upward direction.
We know that if force and displacement is in same direction, work is positive while if force and displacement is in oposite direction, work is negative.
I would mean that, [tex]W_g[/tex] is positive, because gravity is parallel to the displacement and [tex]W_t[/tex] is negative, because the tension is opposite to the displacement.
A car starts from rest and accelerates uniformly over a time of 18 seconds for a distance of 390 m. Determine the acceleration of the car.
Answer:
[tex]a=2.4\ m/s^2[/tex]
Explanation:
Given that,
The initial speed of a car, u = 0
Time, t = 18 s
Distance, d = 390 m
We need to find the acceleration of the car. Let it is a. Using the second equation of motion to find it.
[tex]d=ut+\dfrac{1}{2}at^2[/tex]
or
[tex]d=\dfrac{1}{2}at^2\\\\a=\dfrac{2d}{t^2}\\\\a=\dfrac{2\times 390}{(18)^2}\\\\a=2.4\ m/s^2[/tex]
So, the acceleration of the car is [tex]2.4\ m/s^2[/tex].
A mountain climber, in the process of crossing between two cliffs by a rope, pauses to rest. She weighs 555 N. As the drawing shows, she is closer to the left cliff than to the right cliff, with the result that the tensions in the left and right sides of the rope are not the same. Find the tension in the rope to the left of the mountain climber.
Complete Question
The diagram for this question is shown on the first uploaded image
Answer:
The tension in the rope on the left of the mountain climber is [tex] T_a = 1106 \ N [/tex]
Explanation:
From the question we are told that
The weight of the mountain climber is m = 555 N
Generally from the diagram , the total amount of force acting on the rope along the vertical axis at equilibrium is mathematically represented as
[tex]T_a* cos 65 -555 + T_b * cos(85) = 0[/tex]
Here [tex]T_a, T_b[/tex] are the tension of the rope on the left and on the right hand side
So
[tex]0.423T_a + 0.0871T_b = 555[/tex]
=> [tex] 0.0871T_b = 555 - 0.423T_a[/tex]
=> [tex] T_b = \frac{555 - 0.423T_a}{0.0871}[/tex]
Generally from the diagram , the total amount of force acting on the rope along the horizontal axis at equilibrium is mathematically represented as
[tex]T_a* sin 65 - T_b * sin(85) = 0[/tex]
=> [tex] 0.9063T_a - 0.9962T_b = 0[/tex]
=> [tex] 0.9063T_a = 0.9962T_b [/tex]
=> [tex] 0.9063T_a = 0.9962[\frac{555 - 0.423T_a}{0.0871}] [/tex]
=> [tex] 0.9063T_a = [\frac{552.891 - 0.421T_a}{0.0871}] [/tex]
=> [tex] 0.0789T_a = [552.891 - 0.421T_a[/tex]
=> [tex] 0.4999T_a = 552.891 [/tex]
=> [tex] T_a = 1106 \ N [/tex]
The Jamaican Bobsled Team is sliding down a hill in a toboggan at a rate of 5 m/s when he reaches an even steeper slope. If he accelerates at 2 m/s2 for the 5 m slope, how fast is he traveling when he reaches the bottom of the 5 m slope?
Answer:
6.7 m/s
Explanation:
Given:
Δx = 5 m
v₀ = 5 m/s
a = 2 m/s²
Find: v
v² = v₀² + 2aΔx
v² = (5 m/s)² + 2 (2 m/s²) (5 m)
v = 6.7 m/s
The particles of a more dense substance are closer together
than the particles of a less dense substance.
TRUE
FALSE
The particles of a more dense substance are closer together than the particles of a less dense substance. Thus, the given statement is true.
What is density of particles?Density of the particles is the substance's mass per unit of volume. The symbol which is most often used for the density is ρ (rho), although the Latin letter D can also be used to denote density.
Density is the mass of a unit volume of a material substance or particle. The formula for density is d = M/V (mass per unit volume), where d is density, M is the mass of particle, and V is the volume. Density is commonly expressed in the units of grams per cubic centimeters.
The S.I. unit of density is made up of the mass of the particle which is kg and that of volume is meter cube. Hence, the S.I. unit of density is kg/m³.
Learn more about Density here:
https://brainly.com/question/29775886
#SPJ6
Calculate the work WC done by the gas during the isothermal expansion. Express WC in terms of p0, V0, and Rv.
Complete Question
The complete question is shown on the first and second uploaded image
Answer:
The expression is [tex]W_c = P_o V_o ln (R_v)[/tex]
Explanation:
Generally smallest workdone done by a gas is mathematically represented as
[tex]dW = PdV[/tex]
Generally for an isothermal process
[tex]PV = nRT = constant [/tex]
=> [tex]P = \frac{nRT}{V}[/tex]
Generally the total workdone is mathematically represented as
[tex]W_c = \int\limits^{v_f}_{V_o} {\frac{nRT}{V} } \, dV[/tex]
=> [tex]W_c = nRT \int\limits^{V_f}_{V_o} {\frac{1}{V} } \, dV[/tex]
=> [tex]nRT [lnV] | \left \ {V_f}} \atop {V_o}} \right.[/tex]
=> [tex]W_c = nRT [ln(V_f) - ln(V_o)][/tex]
=> [tex]W_c = nRT ln \frac{V_f}{V_o}[/tex]
From the question [tex]\frac{V_f}{V_o } = R_v[/tex]
=> [tex]W_c = P Vln (R_v)[/tex]
at initial state
[tex]W_c = P_o V_o ln (R_v)[/tex]
A car traveling at 27 m/s slams on its brakes to come to a stop. It decelerates at a rate of 8 m/s2 . What is the stopping distance of the car?
v² - u² = 2 a ∆x
where u = initial velocity (27 m/s), v = final velocity (0), a = acceleration (-8 m/s², taken to be negative because we take direction of movement to be positive), and ∆x = stopping distance.
So
0² - (27 m/s)² = 2 (-8 m/s²) ∆x
∆x = (27 m/s)² / (16 m/s²)
∆x ≈ 45.6 m
The stopping distance of car achieved during the braking is of 45.56 m.
Given data:
The initial speed of car is, u = 27 m/s.
The final speed of car is, v = 0 m/s. (Because car comes to stop finally)
The magnitude of deacceleration is, [tex]a = 8\;\rm m/s^{2}[/tex].
In order to find the stopping distance of the car, we need to use the third kinematic equation of motion. Third kinematic equation of motion is the relation between the initial speed, final speed, acceleration and distance covered.
Therefore,
[tex]v^{2}=u^{2}+2(-a)s[/tex]
Here, s is the stopping distance.
Solving as,
[tex]0^{2}=27^{2}+2(-8)s\\\\s = 45.56 \;\rm m[/tex]
Thus, we can conclude that the stopping distance of car achieved during the braking is of 45.56 m.
Learn more about the kinematic equation of motion here:
https://brainly.com/question/11298125
g A child bounces a 50 g super ball on the sidewalk. The velocity change of the super bowl is from 27 m/s downward to 17 m/s upward. If the contact time with the sidewalk is 1 800 s, what is the magnitude of the average force exerted on the superball by the sidewalk
Answer:
The average force exerted on the superball by the sidewalk is 0.00122 N.
Explanation:
Given;
mass of the super ball, m = 50 g = 0.05 kg
initial velocity of the super bowl, u = -27 m/s (assuming downward motion to be negative)
final velocity of the super bowl, u = 17 m/s (assuming upward motion to be positive)
time of motion, t = 1800 s
The average force exerted on the superball by the sidewalk is given by;
[tex]F = ma\\\\F = \frac{m(v-u)}{t} \\\\F = \frac{0.05(17-(-27))}{1800}\\\\ F = \frac{0.05(44)}{1800}\\\\F = 0.00122 \ N[/tex]
Therefore, the average force exerted on the superball by the sidewalk is 0.00122 N.
A particle is moved along the x-axis by a force that measures 10/(1+x)^2 pounds at a point x feet from the origin. Find the work (in ft-lb) done in moving the particle from the origin to a distance of 9 feet.
Answer:
9 ft*lb
Explanation:
super simple but you just have to understand that the integral is going with the curve
work = integral a to b of f(x)dx = integral 0 to 9 of 10/(1+x)^2dx = 9ft*lb
A car is traveling south at 8.77 m/s. It then begins a uniform acceleration until it reaches a velocity of 47.8 m/s over a period of 3.84s. What is the car's acceleration?
Please help !
Answer:
The acceleration of the car is 10.16m/s²
Explanation:
Given parameters:
Initial velocity = 8.77m/s
Final velocity = 47.8m/s
Time duration = 3.84s
Unknown:
Acceleration of the car = ?
Solution:
To find the acceleration, we must bear in mind that this physical quantity is the change in velocity with time;
Acceleration = [tex]\frac{V - U}{T}[/tex]
V is the final velocity
U is the initial velocity
T is the time taken
Input the parameters and solve for acceleration;
Acceleration = [tex]\frac{47.8 - 8.77}{3.84}[/tex] = 10.16m/s²
The acceleration of the car is 10.16m/s²
Take the regular compass and hold it so the case is vertical. Now use it to investigate the direction of the coil’s magnetic field at locations other than the central axis. What happens as you move away from the center axis toward the coil? What happens above the coil? Outside the coil? Below the coil?
Answer:
Please find the answer in the explanation
Explanation:
Take the regular compass and hold it so the case is vertical. Now use it to investigate the direction of the coil’s magnetic field at locations other than the central axis.
What happens as you move away from the center axis toward the coil? The direction of the magnetic compass needle will move in an opposite direction since the direction of the induced voltage is reversed.
What happens above the coil?
the needle on the magnetic compass will be deflected. Since compasses work by pointing along magnetic field lines
Outside the coil? The magnetic compass needle will experience no deflection. Since there is no induced voltage or current.
Below the coil?
The needle will move in an opposite direction.
The steam from a boiling pot of water is
A: conduction
B: Convection
C: radiation
D: Radiant energy
Converting compound units
You would like to know whether silicon will float in mercury and you know that can determine this based on their densities. Unfortunately, you have the density of mercury in units of kilogram/meter3 and the density of silicon in other units: 2.33 gram/centimeter3. You decide to convert the density of silicon into units of kilogram/meter3 to perform the comparison. By which combination of conversion factors will you multiply 2.33 gram/centimeter3 to perform the unit conversion?
Answer:
Explanation:
Given the density of silicon as 2.33g/cm³
We are to convert this to kg/cm³
We will be using the following conversion factors
1000g = 1kg
2.33g = x
Cross multiply
1000x = 2.33
x = 2.33/1000
x = 0.00233kg
Also we need to convert 1cm³ to 1m³
1cm = 0.01m
1cm³ = 0.01×0.01×0.01
1cm³ = 0.000001m³
Substituting into the density value of silicon
2.33g/cm³ = 0.00233kg/0.000001m³
= 2330kg/m³