The capacity required for statistical TDM = 0.5 × 96,000 bits per second/0.8 = 60,000 bits per second (bps).
The bandwidth required for FDM:If there are twenty-four voice signals that are to be multiplexed and transmitted over twisted pair, what would be the bandwidth required for FDM.
B = 24 × 4 kHz = 96 kHz.TDM using PCM:TDM using PCM requires the following formula to be used.
B = N × R × L,where N = number of sources, R = bit rate per source and L = the number of time slots in a frame. For TDM, the given bandwidth efficiency is 1 bps/Hz.
Problem 2: The block diagram for a TDM PCM system that will accommodate four 300-bps, synchronous, digital inputs and one analog input with a bandwidth of 500 Hz can be drawn as below:Note: The low-pass filter can be used to restrict the input bandwidth of the analog signal. The source encoder is used to encode the samples of the input signal.
Problem 3: Number of devices that could be accommodated by a T1-type TDM line if 1% of the T1 line capacity is reserved for synchronization purposes are as follows:
a. 110-bps teleprinter terminals: 20,000 b. 300-bps computer terminals: 7,352 c. 1200-bps computer terminals: 1,838 d. 9600-bps computer output ports: 230 e. 64-kbps PCM voice-frequency lines: 24The numbers change if each of the sources were transmitting an average of 10% of the time and a statistical multiplexer was used in the following ways: a. 110-bps teleprinter terminals: 500 b. 300-bps computer terminals: 183 c. 1200-bps computer terminals: 46 d. 9600-bps computer output ports: 6 e. 64-kbps PCM voice-frequency lines: 1
Problem 4: Total capacity required for synchronous TDM, if ten 9600-bps lines are to be multiplexed using TDM can be calculated as follows:
The required total bandwidth of the synchronous TDM = 10 × 9600 bits per second
= 96,000 bits per second (bps).The capacity required for statistical TDM can be calculated as follows:
Average link utilization = 0.8 and each TDM link is busy 50% of the time.
Thus, the capacity required for statistical TDM = 0.5 × 96,000 bits per second/0.8 = 60,000 bits per second (bps).
To know more about bandwidth visit:
https://brainly.com/question/31318027
#SPJ11
Why is it generally preferable to use a Logistic Regression classifier rather than a classical Perceptron (i.e., a single layer of threshold logic units trained using the Perceptron training algorithm)? How can you tweak a Perceptron to make it equivalent to a Logistic Regression classifier?
Logistic Regression is generally preferred over a classical Perceptron due to Logistic Regression provides probabilistic outputs. To make a Perceptron equivalent to a Logistic Regression classifier, we can introduce a non-linear activation function such as the sigmoid function.
Logistic Regression is generally preferred over a classical Perceptron for classification tasks due to its several advantages. One key advantage is that Logistic Regression provides probabilistic outputs, which represent the likelihood of belonging to a certain class. This is crucial for tasks that require estimating probabilities or making decisions based on confidence levels. In contrast, the Perceptron only provides binary outputs, making it less flexible.
To make a Perceptron equivalent to a Logistic Regression classifier, we can introduce a non-linear activation function such as the sigmoid function. By applying the sigmoid activation function to the output of the Perceptron, we can map the output to a probability-like range between 0 and 1. This allows us to interpret the output as the estimated probability of belonging to a particular class. Additionally, to ensure a probabilistic interpretation, we can modify the Perceptron training algorithm to optimize a probabilistic loss function such as cross-entropy instead of the traditional Perceptron update rule.
By incorporating the sigmoid activation function and modifying the training algorithm to optimize the cross-entropy loss, we can effectively transform a Perceptron into a classifier with probabilistic outputs, making it equivalent to a Logistic Regression classifier.
To know more about Logistic Regression, visit:
https://brainly.com/question/32505018
#SPJ11
Technician A says that there are nine or more electric motors in electric hybrid vehicles. Technician B says that many of these motors use an electronic module to control their operation. Which technician is correct? A) Technician A only B) Technician B only C) Both technicians D) Neither technician
Both Technician A and Technician B are correct. Electric hybrid vehicles typically have nine or more electric motors, and many of these motors use electronic modules to control their operation.
Technician A is correct because electric hybrid vehicles often employ multiple electric motors for various purposes. These motors can be found in different areas of the vehicle, such as the propulsion system, power steering, braking, and ancillary functions. The number of motors may vary depending on the specific hybrid vehicle model, but it is common to have at least nine electric motors or more in such vehicles.
Technician B is also correct because many electric motors in hybrid vehicles utilize electronic modules to control their operation. These electronic modules, often referred to as motor controllers or inverters, play a crucial role in managing the power flow to the motors, adjusting their speed, and coordinating their actions. These modules incorporate sophisticated electronics and software algorithms to optimize the efficiency and performance of the electric motors, making them an integral part of the hybrid vehicle's overall system.
To learn more about propulsion click here: brainly.com/question/18018497
#SPJ11
Both Technician A and Technician B are correct. Electric hybrid vehicles typically have nine or more electric motors, and many of these motors use electronic modules to control their operation.
Technician A is correct because electric hybrid vehicles often employ multiple electric motors for various purposes. These motors can be found in different areas of the vehicle, such as the propulsion system, power steering, braking, and ancillary functions.
The number of motors may vary depending on the specific hybrid vehicle model, but it is common to have at least nine electric motors or more in such vehicles.
Technician B is also correct because many electric motors in hybrid vehicles utilize electronic modules to control their operation.
These electronic modules, often referred to as motor controllers or inverters, play a crucial role in managing the power flow to the motors, adjusting their speed, and coordinating their actions.
These modules incorporate sophisticated electronics and software algorithms to optimize the efficiency and performance of the electric motors, making them an integral part of the hybrid vehicle's overall system.
To know more about software click here
brainly.com/question/29946531
#SPJ11
Hello,
I need to find the force required to push 300 CC of silicon in two separate syringes. The syringes A and B are fixed to a plate.
Detailed calculations would be appreciated.
To calculate the force required to push 300 CC of silicon in two separate syringes fixed to a plate, we need to consider a few factors. The force required to push 300 CC of silicon through two separate syringes fixed to a plate is 3.925 N.
These factors include the viscosity of the silicon, the diameter of the syringe, and the pressure required to push the silicon through the syringe.
Given that we have limited information about the problem, we will assume a few values to make our calculations more manageable.
Let us assume that the viscosity of the silicon is 10 Pa.s, which is the typical viscosity of silicon. We will also assume that the diameter of the syringe is 1 cm, and the pressure required to push the silicon through the syringe is 10 Pa.
To calculate the force required to push 300 CC of silicon in two separate syringes fixed to a plate, we will use the formula:
F = (P * A)/2
Where F is the force required, P is the pressure required, and A is the area of the syringe.
The area of the syringe is given by:
A = π * (d/2)^2
Where d is the diameter of the syringe.
Substituting the values we assumed, we get:
A = π * (1/2)^2 = 0.785 cm^2
Therefore, the force required to push 300 CC of silicon through two separate syringes fixed to a plate is:
F = (10 * 0.785)/2 = 3.925 N
To know more about force visit:
https://brainly.com/question/30507236
#SPJ11
A torsional pendulum has a centroidal mass moment of inertia of 0.65 kg-m2 and when given an initial twist and released is found to have a frequency of oscillation of 200 rpm. Knowing that when this pendulum is immersed in oil and given the same initial condition it is found to have a frequency of oscillation of 180 rpm, determine the damping constant for the oil. The damping constant for the oil is
A torsional pendulum has a centroidal mass moment of inertia of 0.65 kg-m² and when given an initial twist and released is found to have a frequency of oscillation of 200 rpm.
Knowing that when this pendulum is immersed in oil and given the same initial condition it is found to have a frequency of oscillation of 180 rpm, determine the damping constant for the oil. The damping constant for the oil can be calculated using the following formula.
The frequency of oscillation of the pendulum without oil is given as; f₁=200 rpmand the frequency of oscillation of the pendulum with oil is given as; f₂=180 rpm Now, substituting the values of f₁ and f₂ in the damping constant formula;
[tex]k= 2π (f₁-f₂)/ln(f₁/f₂)=2π (200-180)/ln(200/180)= 2π (20)/ln(10/9)≈ 15.10[/tex]
Therefore, the damping constant for the oil is 15.10.
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
This code segment read the elements for the array M(10) using input box, then calculate the product (the result of multiplying) of elements greater than the number 5. Then print the final result of the multiplication. 1-............ For I 1 To 10 M(I) = InputBox("M") 2-.......... 3-...... 4-....... 5-......... 6-...... O 1-P = 12-lf M(I) > 5 Then 3-P = P * M(I) 4-End If 5-Next 6-Print P O 1-P = 1 2-lf M(1) > 5 Then 3-P = P * M(1) 4-End If 5-Print P 6-Next O 1-P = 0 2-lf M(1) > 5 Then 3-P = P * M(1) 4-End If 5-Next 6-Print P O 1-P = 1 2-1f M(1) > 5 Then 3-P = P * M(1) 4-Next 5- End If 6-Print P O 1-P = 1 2-lf M(I) <=5 Then 3-P = P * M(I) 4-End If 5-Next 6-Print P
The product (the result of multiplying) of elements greater than the number 5 in the code is given below.
Given the code segment read the elements for the array M(10) using input box, then compute the product (the result of multiplying) of elements greater than the number 5.
Then the code could be written:
```
Dim M(10), P
P = 1
For i = 1 To 10
M(i) = InputBox("Enter a number:")
If M(i) > 5 Then
P = P * M(i)
End If
Next
Print "Product of elements greater than 5: " & P
```
LEarn more about array here;
https://brainly.com/question/33364957
#SPJ4
QUESTION 3 An engineer in the design team is finalizing the design for the pressing cylinder - cylinder P - in the upgraded stamping machine. a. The engineer suggested the use speed controllers to control the speed of the double acting cylinder. Draw a pneumatic circuit showing the proper connection speed controllers to a double acting cylinder and a 5/2 way pilot operated valve. [C6, SP1, SP3] [5 marks] b. The engineer suggested 2 cylinders for your evaluation. The first proposed cylinder is 12 mm diameter cylinder with the radius of cylinder rod of 2 mm. The second proposed cylinder is 16 mm diameter cylinder with the radius of cylinder rod of 4 mm. Evaluate the cylinders and recommend which cylinder delivers a higher cylinder force. Assume pressure, Pauge=4 bar. [CS, SP4] [5 marks] c. The engineering team has asked you to design an upgraded stamping machine using double acting cylinders arranged in the following sequence: Start, C+, C-, B+, A+, A-, X-, X+, B- Design a pneumatic circuit using basic sequence technique for this machine. [C5, SP4] [15 marks
Answer:a. The circuit for the speed controller can be designed using a 5/2 way pilot-operated valve in combination with a double-acting cylinder. It should be noted that a pilot-operated valve cannot provide fluidic resistance, making it necessary to include a separate flow control valve between the pilot-operated valve and the cylinder. Below is the circuit diagram:b.
To evaluate the force produced by the cylinders, we can use the formula for force: Force= Pressure x AreaFor the 12 mm cylinder: Force= 4 x π(0.012² - 0.002²)= 0.441 NFor the 16 mm cylinder: Force= 4 x π(0.016² - 0.004²)= 1.005 NThe cylinder with a diameter of 16 mm and a rod radius of 4 mm produces a higher force than the cylinder with a diameter of 12 mm and a rod radius of 2 mm. c. The sequence for the upgraded stamping machine can be represented using basic sequence technique. The basic sequence technique includes three positions of the directional control valve and five ports. Port A and port B are the supply ports while ports P and T are the exhaust ports. Below is the circuit diagram for the upgraded stamping machine
:The given problem involves designing a pneumatic circuit for the upgraded stamping machine using a double-acting cylinder. The design engineer suggested the use of speed controllers to control the speed of the cylinder.The pneumatic circuit for the speed controller can be designed using a 5/2 way pilot-operated valve in combination with a double-acting cylinder. The circuit diagram should include a flow control valve between the pilot-operated valve and the cylinder. The evaluation of the force produced by the cylinders involves the use of the formula for force, which is force= pressure x area.The basic sequence technique can be used to design the pneumatic circuit for the upgraded stamping machine. This technique includes three positions of the directional control valve and five ports. Port A and port B are the supply ports, while ports P and T are the exhaust ports.
To know more about cylinder visit:
https://brainly.com/question/31462197
#SPJ11
Neurons conduct electrical impulses by using the action potential. Describe how an action potential is generated at a neuron. Include in your description the typical action potential waveform with labelling.
The action potential is an all-or-nothing event, meaning that once it is initiated, it will continue until it reaches the end of the axon. The action potential is generated at the axon hillock, the region where the axon originates from the cell body. The action potential waveform is generated by the movement of ions across the neuron's membrane.
A neuron is the basic functional unit of the nervous system. Neurons are cells that are specialized in the processing and transmitting of information by electrical and chemical signals. A neuron has a cell body, dendrites, and an axon. Dendrites receive signals from other neurons, while axons transmit signals to other neurons. Neurons conduct electrical impulses by using the action potential, which is a brief reversal of membrane potential generated by the movement of ions across the neuron's membrane.Action potential generation is a complex process that involves the movement of ions across the neuron's membrane.
At resting potential, the neuron's membrane potential is negative inside and positive outside. When a stimulus is applied to the neuron, it causes depolarization, which is the movement of positive ions into the neuron, resulting in a more positive membrane potential. When the membrane potential reaches a threshold level, an action potential is generated.The typical action potential waveform has four phases: resting potential, depolarization, repolarization, and hyperpolarization. During the resting potential phase, the membrane potential is negative inside and positive outside.
During the depolarization phase, the membrane potential becomes more positive as positive ions, primarily sodium ions, rush into the neuron. During the repolarization phase, the membrane potential becomes negative again as positive ions leave the neuron, primarily potassium ions. During the hyperpolarization phase, the membrane potential becomes more negative than resting potential as potassium ions continue to leave the neuron.
To know more about Neuron visit :
https://brainly.com/question/29451794
#SPJ11
What is X-ray computed tomography (X-CT)? What is the typical configuration of an X-CT scanner?
List some applications of X-CT around you? And try to explain their working principle.
In your opinion, what factors determine the quality of CT images? And try to give some discussion.
What can X-CT do for industries? And try to give some examples.
X-ray computed tomography (X-CT) is a medical imaging technique that uses X-ray technology to generate detailed cross-sectional images of the body. The typical configuration of an X-CT scanner involves a rotating X-ray source and detectors that capture the transmitted X-rays from multiple angles as they pass through the body. These captured data are then processed by a computer to construct a three-dimensional image of the scanned area.
Applications of X-CT can be found in various fields, including medicine, research, and industry. In medicine, X-CT is commonly used for diagnosing and monitoring diseases, planning surgeries, and evaluating treatment responses. In research, X-CT aids in studying anatomical structures, investigating biological processes, and developing new medical techniques. In industrial settings, X-CT plays a crucial role in non-destructive testing, quality control, and product development, enabling the inspection of internal structures and detecting defects.
The quality of CT images is influenced by several factors. One key factor is the spatial resolution, which determines the level of detail captured in the images. Higher spatial resolution allows for better visualization of small structures, but it may result in increased radiation dose to the patient. Image noise is another factor, with lower noise levels corresponding to clearer images. The choice of imaging parameters, such as X-ray energy, exposure time, and detector sensitivity, can impact both spatial resolution and noise. Additionally, the patient's motion during scanning and the presence of artifacts can also affect image quality.
To learn more about tomography click here: brainly.com/question/32222524
#SPJ11
X-ray computed tomography (X-CT) is a medical imaging technique that uses X-ray technology to generate detailed cross-sectional images of the body.
The typical configuration of an X-CT scanner involves a rotating X-ray source and detectors that capture the transmitted X-rays from multiple angles as they pass through the body. These captured data are then processed by a computer to construct a three-dimensional image of the scanned area.
Applications of X-CT can be found in various fields, including medicine, research, and industry. In medicine, X-CT is commonly used for diagnosing and monitoring diseases, planning surgeries, and evaluating treatment responses.
In research, X-CT aids in studying anatomical structures, investigating biological processes, and developing new medical techniques.
In industrial settings, X-CT plays a crucial role in non-destructive testing, quality control, and product development, enabling the inspection of internal structures and detecting defects.
The quality of CT images is influenced by several factors. One key factor is the spatial resolution, which determines the level of detail captured in the images.
Higher spatial resolution allows for better visualization of small structures, but it may result in increased radiation dose to the patient. Image noise is another factor, with lower noise levels corresponding to clearer images.
The choice of imaging parameters, such as X-ray energy, exposure time, and detector sensitivity, can impact both spatial resolution and noise. Additionally, the patient's motion during scanning and the presence of artifacts can also affect image quality.
To learn more about tomography click here:
brainly.com/question/32222524
#SPJ11
Cryopreservation is the process by which biological material is preserved through a fast-cooling process. The intent of fast cooling is to drop the temperature of the cellular materials so quickly that there is not time for the water to create damaging ice crystals. Rather, the water vitrifies in an amorphic state. You decide to carry out preliminary chilling experiments using a cold bath of liquid ammonia that is kept at -53 degree C. A cellular iceball with diameter of 0.1 mm starts out at a uniform 0 degree C before it is plunged into the liquid ammonia, as suggested in the sketch below. The heat transfer coefficient can be assumed to be h=5000 W/m^2K. Thermal properties for the ice ball are k= 2.5 W/m-K rho= 920 kg/m^3 and cp=1.882 kj/kg-K
Find:
A) Determine an appropriate transient model for the spherical iceball. Clearly show the criteria used to identify the modeling approach, and then describe the model that needs to be used for finding the temperature at the center of the iceball as a function of time( the equation(s)/figures that would be used)
B) Determine the temperature in degree C for the centerpoint of iceball after 2 milli-seconds in the ammonia bath.
The temperature at the centerpoint of the iceball can be obtained from the numerical solution at the desired time point of 2 milliseconds.
To determine an appropriate transient model for the spherical iceball, the criteria used would include the assumption of a homogeneous and isotropic iceball, neglecting any internal heat generation, and considering one-dimensional radial heat conduction. The appropriate model for finding the temperature at the center of the iceball as a function of time is the transient conduction equation for a spherical coordinate system:ρc_p(∂T/∂t) = (1/r^2)(∂/∂r)(r^2k(∂T/∂r))Where ρ is the density, c_p is the specific heat capacity, k is the thermal conductivity, T is the temperature, t is time, and r is the radial distance. To determine the temperature at the center of the iceball after 2 milliseconds, the transient conduction equation needs to be solved numerically using appropriate boundary and initial conditions. The specific values of density (ρ), specific heat capacity (c_p), thermal conductivity (k), initial temperature (T_0), and the boundary condition (T_inf) should be substituted into the equation. The resulting temperature distribution within the iceball can then be calculated as a function of time using numerical methods, such as finite difference or finite element analysis.
To know more about milliseconds click the link below:
brainly.com/question/31500009
#SPJ11
A helical spring is made of hard-drawn spring steel
wire 2 mm in diameter and has an outside diameter of 22 mm. The
ends are plain and ground, and there are 8 1/2 total coils.
The helical spring is made of hard-drawn spring steel wire, 2 mm in diameter, with an outside diameter of 22 mm and 8 1/2 total coils.
What are the specifications of the helical spring made of hard-drawn spring steel wire, including its diameter, outside diameter, and total number of coils?The helical spring in question is constructed using hard-drawn spring steel wire, which has a diameter of 2 mm.
The spring has an outside diameter of 22 mm, indicating the size of the coil.
The ends of the spring are plain and ground, ensuring a smooth and even surface.
The spring consists of a total of 8 1/2 coils, representing the number of complete rotations formed by the wire.
This design and construction allow the spring to possess elastic properties, enabling it to store and release mechanical energy when subjected to external forces or loads.
The use of hard-drawn spring steel provides the necessary strength and resilience for the spring to effectively perform its intended function in various applications such as mechanical systems, automotive components, and industrial machinery.
Learn more about helical spring
brainly.com/question/14283430
#SPJ11
what is athree quadrant dc drive
A three-quadrant DC drive refers to a type of DC motor drive system that can operate in three different quadrants of the motor's speed-torque characteristic. In DC drives, the quadrants represent different combinations of motor speed and torque.
The four quadrants in a DC motor drive system are:
Quadrant I: Forward motoring - Positive speed and positive torque.
Quadrant II: Forward braking or regenerative braking - Negative speed and positive torque.
Quadrant III: Reverse motoring - Negative speed and negative torque.
Quadrant IV: Reverse braking or regenerative braking - Positive speed and negative torque.
A three-quadrant DC drive is capable of operating in three of these quadrants, excluding one of the braking quadrants. Typically, a three-quadrant DC drive allows for forward motoring, forward braking/regenerative braking, and reverse motoring.
This type of drive is commonly used in applications where bidirectional control of the DC motor is required, such as in electric vehicles, cranes, elevators, and rolling mills.
By providing control over motor speed and torque in multiple directions, a three-quadrant DC drive enables precise and efficient control of the motor's operation, allowing for smooth acceleration, deceleration, and reversing capabilities.
to learn more about DC drive.
https://brainly.com/question/14268310
Compute the coefficient of friction of -10°C air flowing with a mean velocity of 5 m/s in a circular
sheet-metal duct 400 mm in diameter and 10 m long.
A 0.0151
B 0.0155
C 0.0159
D 0.0152
Therefore, the coefficient of friction of -10°C air flowing with a mean velocity of 5 m/s in a circular sheet-metal duct 400 mm in diameter and 10 m long is approximately 0.0155.
The Reynolds number of the airflow in the duct can be calculated using the formula: Re = (ρvd) / μWhere:
ρ = air density
v = mean velocity
d = duct diameter
μ = air viscosity at -10°C
Using the above formula, we have:
ρ = 1.307 kg/m³ (density of air at -10°C)
v = 5 m/s (given)
d = 400 mm = 0.4 m (given)
μ = 2.005 x 10^-5 Ns/m² (viscosity of air at -10°C)
Plugging in the values, we get:
Re = (1.307 x 5 x 0.4) / (2.005 x 10^-5)
Re ≈ 1.64 x 10^6
The friction factor can be obtained using the Colebrook-White equation:
1/√f = -2.0log((ε/d)/3.7 + 2.51/(Re√f))
Where:
ε = surface roughness of duct
d = duct diameter
Re = Reynolds number
Assuming the surface roughness of the sheet-metal duct is 0.03 mm (which is typical), we have:
ε = 0.03 mm = 0.00003 m
d = 0.4 m (given)
Re = 1.64 x 10^6 (calculated above)
Substituting the values into the Colebrook-White equation and solving for f using a numerical method (e.g. iterative), we get:
f ≈ 0.0155
Therefore, option B (0.0155) is the correct option.
To know more about friction visit:
https://brainly.com/question/28356847
#SPJ11
An inductor L, resistor R, of value 5 2 and resistor R, of value 10 2 are connected in series with a voltage source of value V(t) = 50 cos cot. If the power consumed by the R, resistor is 10 W, calculate the power factor of the circuit. [5 Marks]
The power factor of the circuit is 0.2.
To calculate the power factor of the circuit, we need to determine the phase relationship between the current and voltage in the circuit.
Given that the power consumed by the R2 resistor is 10 W, we can use the formula for power in an AC circuit:
P = IV cos φ
where P is the power, I is the current, V is the voltage, and φ is the phase angle between the current and voltage.
In this case, the power consumed by the R2 resistor is given as 10 W. We know that the voltage across the resistor is the same as the source voltage V(t) since they are connected in series. Therefore, we can rewrite the equation as:
10 = V cos φ
Substituting the given voltage source V(t) = 50 cos ωt, we have:
10 = 50 cos φ
Simplifying the equation, we find:
cos φ = 10/50 = 0.2
Know more about AC circuit here:
https://brainly.com/question/1542791
#SPJ11
The First Law of Thermodynamics QUESTIONS: 1. When a fluid is vaporized, the temperature does not change during the process as heat is added. What is the specific heat for this process? 2. Discuss the problems associated with the Bernoulli equation. 3. With all of the problems associated with the Bernoulli equation, why is it still used? 4. An automobile engine consists of a number of pistons and cylinders. If a complete cycle of the events that occur in each cylinder can be considered to consist of a number of nonflow events, can the engine be considered a nonflow device? 5. Can you name or describe some adiabatic processes?
The First Law of Thermodynamics
The First Law of Thermodynamics is simply a statement of the conservation of energy principle.
It states that energy cannot be created or destroyed, only transferred or converted from one form to another.
The first law of thermodynamics is based on the concept of internal energy, which is the energy associated with the motion and configuration of the atoms and molecules that make up a system.
1. For a process where a fluid is vaporized, the temperature does not change during the process as heat is added.
What is the specific heat for this process?
The specific heat for the process of vaporization is known as latent heat.
The specific heat for this process is equal to the amount of heat required to convert a unit mass of a substance from a solid or liquid state into a vapor state without any change in temperature.
2. Discuss the problems associated with the Bernoulli equation.
The Bernoulli equation is based on the conservation of energy principle, which states that energy cannot be created or destroyed, only transferred or converted from one form to another.
However, there are some problems associated with the Bernoulli equation, including: The equation assumes that the fluid is incompressible.
This means that the density of the fluid remains constant throughout the flow.
The equation assumes that the flow is steady, which means that the velocity of the fluid does not change with time.
The equation assumes that the flow is irrotational, which means that there is no turbulence in the flow.
3. With all of the problems associated with the Bernoulli equation, why is it still used?
Despite the problems associated with the Bernoulli equation, it is still used because it provides a simple and useful way of describing fluid flow.
It is also a useful tool for engineers who need to design fluid systems.
The Bernoulli equation is particularly useful for analyzing fluid flow through pipes and ducts, and it is also used to design aerodynamic systems such as airplane wings and wind turbines.
4. An automobile engine consists of a number of pistons and cylinders.
If a complete cycle of the events that occur in each cylinder can be considered to consist of a number of nonflow events, can the engine be considered a nonflow device?
No, an automobile engine cannot be considered a nonflow device, even if a complete cycle of the events that occur in each cylinder can be considered to consist of a number of nonflow events.
This is because an engine is a device that involves the transfer of energy from one form to another. In an engine, chemical energy is converted into mechanical energy, which is then used to power the vehicle.
5. Can you name or describe some adiabatic processes?
Adiabatic processes are processes that occur without the transfer of heat between the system and its surroundings.
Some examples of adiabatic processes include:
Isochoric process: This is a process that occurs at constant volume.
During an isochoric process, the work done by the system is zero, and there is no change in the internal energy of the system.
Isobaric process: This is a process that occurs at constant pressure.
During an isobaric process, the work done by the system is equal to the change in the internal energy of the system.
Adiabatic process: This is a process that occurs without the transfer of heat between the system and its surroundings.
During an adiabatic process, the work done by the system is equal to the change in the internal energy of the system.
To know more about atoms, visit:
https://brainly.com/question/1566330
#SPJ11
Composite Product/Process Matching. (
Ladder____
Pressurized gas cylinder____
Shower enclosure____ Fireman's helmet____
Aircraft wing____ a. Filament winding b. Spray-up c. Pultrusion d. Automated prepreg tape laying e. Compression molding
The manufacturing techniques associated with the given examples are as follows:
a. Filament winding: This method is used to create composite structures by winding continuous filaments around a rotating mandrel. It is suitable for producing fireman's helmets that require Pultrusion and impact resistance.
b. Spray-up: Also known as open molding, this process involves spraying or manually placing fiberglass or other reinforcements into a mold. It is commonly used for manufacturing shower enclosures due to its flexibility and ease of customization.
c. Pultrusion: This continuous manufacturing process is used to produce composite profiles with a constant cross-section. It is commonly employed for manufacturing ladders, which require high strength and lightweight properties.
d. Automated prepreg tape laying: This technique involves automated placement of pre-impregnated fiber tape onto a mold to create composite structures. It is utilized in the production of aircraft wings to ensure precision and consistent fiber alignment.
e. Compression molding: This method involves placing a preheated composite material into a mold and applying pressure to shape and cure it. It is used for manufacturing pressurized gas cylinders to ensure structural integrity and pressure resistance.
These manufacturing techniques are chosen based on the specific requirements of each product to achieve the desired properties, strength, and functionality.
To know more about Pultrusion, visit
https://brainly.com/question/33289071
#SPJ11
Which of the given statement is true for a zero-order system?
Varying transfer function with time
Constant transfer function
Transfer function = 1/S
Transfer function = 1/S²
The statement "Transfer function = 1/S" is true for a zero-order system.
In control systems, the transfer function is a mathematical representation of the relationship between the input and output of a system. It describes how the system responds to different input signals. In the case of a zero-order system, the transfer function is given by "Transfer function = 1/S", where S represents the Laplace variable. A zero-order system is characterized by a transfer function that does not contain any poles in the denominator. This means that the system's output is only dependent on the current value of the input, without any influence from past or future values. The transfer function "1/S" represents a system with a constant gain, where the output is directly proportional to the input. It indicates that the system has no internal dynamics or time delays. Therefore, among the given options, the statement "Transfer function = 1/S" is the one that accurately describes a zero-order system.
Learn more about Laplace variable here:
https://brainly.com/question/31481915
#SPJ11
Implement a parameterizable 3:1 multiplexer. Make the default
bit-width 10 bits.
Here is the implementation of a parameterizable 3:1 multiplexer with a default bit-width of 10 bits.
The mux_3to1 module takes three input data signals (data0, data1, data2) of width WIDTH and a 2-bit select signal (select). The output signal (output) is also of width WIDTH.
Inside the always block, a case statement is used to select the appropriate data input based on the select signal. If select is 2'b00, data0 is assigned to the output. If select is 2'b01, data1 is assigned to the output. If select is 2'b10, data2 is assigned to the output. In the case of an invalid select value, the default assignment is data0.
You can instantiate this mux _3to1 module in your design, specifying the desired WIDTH parameter value. By default, it will be set to 10 bits.
To know more about data signals visit:
https://brainly.com/question/32391218
#SPJ11
If we double the amount of cement, what would you expect to
happen to: - Compressive Strength - Workability - Dureability
Advantages of renewable energy sources include reduced greenhouse gas emissions, energy sustainability, and potential for job creation. Disadvantages include intermittency, high initial costs, and dependence on weather conditions.
What are the advantages and disadvantages of using renewable energy sources?If we double the amount of cement in a concrete mix, the expected effects on compressive strength, workability, and durability are as follows:
- Compressive Strength: Increasing the amount of cement generally leads to higher compressive strength in concrete. This is because cement is the binding material that provides strength to the concrete matrix. Therefore, doubling the amount of cement would likely result in increased compressive strength.
- Workability: Workability refers to the ease with which concrete can be mixed, placed, and finished. Increasing the amount of cement can decrease the workability of concrete. With higher cement content, the concrete mixture becomes stiffer and less fluid, making it more difficult to work with and shape. Additional water or additives may be required to maintain the desired workability.
- Durability: Increasing the amount of cement can improve the durability of concrete in certain aspects. Cement provides chemical and physical stability to the concrete, enhancing its resistance to environmental factors such as moisture, chemical attack, and abrasion. However, excessive cement content can also lead to increased shrinkage and cracking, which can compromise durability. Proper proportions and mix design considerations are crucial to achieving the desired durability.
Learn more about Disadvantages
brainly.com/question/29548862
#SPJ11
A Δ-connected source supplies power to a Y-connected load in a three-phase balanced system. Given that the line impedance is 3+j1Ω per phase while the load impedance is 6+j4Ω per phase, find the magnitude of the line voltage at the load. Assume the source phase voltage V ab= 208∠0∘ Vrms. A. VLL=125.5Vrms at the load B. VLL=145.7Vrms at the load C. VLL=150.1Vrms at the load D. VLL=130.2Vrms at the load
Given that the line impedance is 3+j1Ω per phase while the load impedance is 6+j4Ω per phase, find the magnitude of the line voltage at the load. Assume the source phase voltage Vab= 208∠0∘ Vrms.
The line voltage per phase, Vl = Vab - ILine (ZLine)Where Vab is the source phase voltage, and ILine is the line current.
The phase currents in the load, IPhase = Vab / ZLoad = (208 / √3 ) ∠0° / (6 + j4) = 20.97 ∠-36.87°
The line current,
ILine = √3 IPhase = 36.34 ∠-36.87°
The line impedance, ZLine = 3 + j1 Ω (per phase)
The line voltage, Vl = Vab - ILine (ZLine) = (208 / √3) ∠0° - 36.34 ∠-36.87° (3 + j1) V= 145.7 ∠2.77° VRMS, approximately 146 VRMS
The line voltage is, VLL = √3 VL = √3 (145.7) = 251.89 Vrms ≈ 252 Vrms
The answer is B. VLL=145.7Vrms at the load.
To know more about the voltage, visit:
https://brainly.com/question/31215137
#SPJ11
An airport is to be constructed at a site 190m above mean sea level and on a level ground. The runway length required under standard atmospheric condition at sea level for landing is considered as 2100m and for take-off as 1600m respectively. Determine the actual runway length to be provided at this airport site. Airport reference temperature may be considered as 21-degree C
The actual runway length to be provided at the airport site 190m above mean sea level is 2171m.
The required runway length for landing under standard atmospheric conditions at sea level is 2100m, while for take-off it is 1600m. However, since the airport site is located 190m above mean sea level, the altitude needs to be taken into account when determining the actual runway length.
As altitude increases, the air density decreases, which affects the aircraft's performance during take-off and landing. To compensate for this, additional runway length is required. The specific calculation for this adjustment depends on various factors, including temperature, pressure, and the aircraft's performance characteristics.
In this case, we can use the International Civil Aviation Organization (ICAO) standard formula to calculate the adjustment factor. According to the formula, for every 30 meters of altitude above mean sea level, an additional 7% of runway length is required for take-off and 15% for landing.
For the given airport site at 190m above mean sea level, we can calculate the adjustment as follows:
Additional runway length for take-off: 190m / 30m * 7% of 1600m = 76m
Additional runway length for landing: 190m / 30m * 15% of 2100m = 199.5m
Adding these adjustment lengths to the original required runway lengths, we get:
Actual runway length for take-off: 1600m + 76m = 1676m
Actual runway length for landing: 2100m + 199.5m = 2299.5m
Rounding up to the nearest whole number, the actual runway length to be provided at this airport site is 2299.5m.
Learn more about Runway length
brainly.com/question/30909833
#SPJ11
a) name some of the metallic and none metallic materials used in pump construction against the following applications, a) Hazardous nature fluids b) High temperature fluids c)Corrosive fluids.
Pumps are used in numerous industrial and domestic applications, from moving water and sewage to chemicals and petroleum products.
The materials utilized for constructing pumps must be compatible with the liquids being handled. This can necessitate the use of different materials for different fluids. This text discusses the metallic and non-metallic materials used in pump construction for handling hazardous, high-temperature, and corrosive fluids.The materials utilized for constructing pumps must be compatible with the liquids being handled. This can necessitate the use of different materials for different fluids.The following materials can be used in pump construction, depending on the nature of the fluids being handled:
a) Hazardous Nature Fluids: Materials such as stainless steel, nickel, and chrome are frequently utilized in the construction of pumps that handle hazardous fluids.
b) High-Temperature Fluids: When handling high-temperature fluids, pump components are frequently constructed of metals like carbon steel, stainless steel, and bronze, as well as materials like ceramic and tungsten carbide.
c) Corrosive Fluids: Stainless steel, nickel, and ceramics are used to construct pumps that handle corrosive fluids. Non-metallic materials like carbon fiber-reinforced polymer, polytetrafluoroethylene, and ethylene propylene diene monomer are often employed because of their corrosion resistance properties.In conclusion, pumps are constructed using a variety of materials to handle different fluids.
Materials such as stainless steel, nickel, and chrome are frequently utilized in the construction of pumps that handle hazardous fluids, while high-temperature fluids are frequently handled with materials like carbon steel, stainless steel, and bronze, as well as materials like ceramic and tungsten carbide. Finally, stainless steel, nickel, ceramics, carbon fiber-reinforced polymer, polytetrafluoroethylene, and ethylene propylene diene monomer are commonly used for pumps that handle corrosive fluids.
Learn more about Pumps :
https://brainly.com/question/32052332
#SPJ11
8.7 Reheat in a vapor power cycle is the performance improvement
strategy that increases ________________ .
sponding isentropic expansion is 8.7 Reheat in a vapor power cycle is the performance improvement strategy that increases 8.8 A direct-contact-type heat exchanger found in regenerative vapor
The missing word in the sentence is "efficiency". The performance improvement strategy that increases efficiency in a vapor power cycle is reheat. In a reheat cycle, steam is extracted from the turbine and sent back to the boiler to be reheated.
This increases the average temperature of heat addition to the cycle, which in turn increases the cycle's efficiency. The steam is then sent back to the turbine, where it goes through another set of expansion and condensation processes before being extracted again for reheat. This cycle is repeated until the steam reaches the desired temperature and pressure levels.
The regenerative vapor cycle makes use of a direct-contact-type heat exchanger. In this type of heat exchanger, hot steam coming from the turbine is brought into contact with cooler water, which absorbs the steam's heat and turns it into liquid. The liquid water is then sent back to the boiler, where it is reheated and reused in the cycle. This type of heat exchanger increases the cycle's efficiency by reducing the amount of heat lost in the condenser and increasing the amount of heat added to the cycle.Overall, the reheat and regenerative vapor power cycle strategies are effective ways to increase the efficiency of vapor power cycles. By increasing the average temperature of heat addition and reducing heat losses, these strategies can improve the cycle's performance and reduce fuel consumption.Answer: The missing word in the sentence is "efficiency".
To know more about cycle visit:
https://brainly.com/question/31391800
#SPJ11
A 12N force is required to turn a screw of body diameter equal
to 6mm and 1mm pitch. Calculate the driving force acting on the
screw.
A. 452N
B. 144N
C. 24N
The driving force acting on the screw is 36 N. None of the options provided (A, B, or C) match the calculated value.
To calculate the driving force acting on the screw, we can use the equation:
Driving force = Torque / Lever arm
The torque required to turn the screw can be calculated as the product of the force applied and the radius of the screw:
Torque = Force * Radius
Given:
Force required to turn the screw = 12 N
Body diameter of the screw = 6 mm
Pitch of the screw = 1 mm
The radius of the screw can be calculated by dividing the diameter by 2:
Radius = Body diameter / 2 = 6 mm / 2 = 3 mm = 0.003 m
Now we can calculate the torque:
Torque = Force * Radius = 12 N * 0.003 m = 0.036 Nm
To calculate the driving force, we need to determine the lever arm of the screw. In this case, the lever arm is the pitch of the screw:
Lever arm = Pitch = 1 mm = 0.001 m
Finally, we can calculate the driving force:
Driving force = Torque / Lever arm = 0.036 Nm / 0.001 m = 36 N
To learn more about driving force, click here:
https://brainly.com/question/29795032
#SPJ11
Explain why a diesel engine can operate at very high air fuel ratios but the gasoline engine must operate at close to the stoichiometric air fuel ratio.
diesel engines can operate at higher air-fuel ratios due to their compression ignition process, while gasoline engines require a near stoichiometric air-fuel ratio to ensure proper combustion and prevent knocking.
The difference in the air-fuel ratio requirements between a diesel engine and a gasoline engine can be explained by their respective combustion processes and fuel properties.
In a diesel engine, combustion is achieved through the process of compression ignition. The air and fuel are introduced separately into the combustion chamber. The high compression ratio and temperature in the cylinder cause the air to reach a state of high pressure and temperature. When fuel is injected into the cylinder, it rapidly ignites due to the high temperature and pressure, leading to combustion. Since the combustion is initiated by compression rather than a spark, diesel engines can operate at higher air-fuel ratios, commonly referred to as "lean" conditions.
On the other hand, gasoline engines use spark ignition, where a spark plug ignites the air-fuel mixture. Gasoline has a lower auto-ignition temperature compared to diesel fuel, making it more prone to knocking and misfires under lean conditions. Therefore, gasoline engines are designed to operate at or near the stoichiometric air-fuel ratio, which provides the ideal balance between complete combustion and avoiding knocking. The stoichiometric ratio ensures that there is enough fuel available to react with all the oxygen in the air, resulting in complete combustion and maximum power output.
To know more about diesel engines, visit:
https://brainly.com/question/13147547
#SPJ11
HW11: suppose the length of a sequence is 1000 (points) and sampling frequency is 3000HZ There are two peaks in the DFT of the sequence at P1=17 and P2 = 364, respectively. compute the corresponding frequency in the sequence.
The corresponding frequencies in the sequence for Peak 1 and Peak 2 are 51 Hz and 1092 Hz, respectively.
To compute the corresponding frequency in the sequence, we can use the formula:
frequency = (peak_index / sequence_length) * sampling_frequency
Given:
Sequence length (N) = 1000
Sampling frequency (Fs) = 3000 Hz
Peak 1 (P1) = 17
Peak 2 (P2) = 364
For Peak 1:
frequency1 = (P1 / N) * Fs
= (17 / 1000) * 3000
= 51 Hz
For Peak 2:
frequency2 = (P2 / N) * Fs
= (364 / 1000) * 3000
= 1092 Hz
Therefore, the corresponding frequencies in the sequence for Peak 1 and Peak 2 are 51 Hz and 1092 Hz, respectively.
Know more about frequencies here:
https://brainly.com/question/29739263
#SPJ11
A V8 engine with 7.5-cm bores is redesigned from two valves per cylinder to four valves per cylinder. The old design had one inlet valve of 34 mm diameter and one exhaust valve of 29 mm diameter per cylinder. This is replaced with two inlet valves of 27 mm diameter and two exhaust valves of 23 mm diameter. Maximum valve lift equals 22% of the valve diameter for all valves. Calculate: a. Increase of inlet flow area per cylinder when the valves are fully open. b. Give advantages and disadvantages of the new system.
A V8 engine with 7.5 cm bores was redesigned from two valves per cylinder to four valves per cylinder. The old design had one inlet valve of 34 mm diameter and one exhaust valve of 29 mm diameter per cylinder.
This was replaced with two inlet valves of 27 mm diameter and two exhaust valves of 23 mm diameter. Maximum valve lift equals 22% of the valve diameter for all valves. The cross-sectional area of flow for the inlet valve is given by: Area of flow = 0.22 x (diameter of the valve)²For the old design, Area of flow = 0.22 x (34 mm)² = 310.88 mm²For the new design, Area of flow = 0.22 x (27 mm)² x 2 = 306.36 mm²Increase in inlet flow area per cylinder = (306.36 - 310.88) mm² = -4.52 mm²When the valves are fully open, the inlet flow area per cylinder reduces by 4.52 mm².
In general, a four-valve engine provides a higher ratio of valve area to bore area than a two-valve engine of the same size. Advantages of the new system are:Improved breathing efficiency due to better gas flow through the engine. The greater number of smaller valves results in a more compact combustion chamber, which leads to an increased compression ratio.Disadvantages of the new system are:An increased number of valves increases the complexity of the valve-train, adding weight and complexity to the engine. This means that a four-valve engine will be more expensive to manufacture and maintain than a two-valve engine of the same size.
To know more about diameter per cylinder visit:
brainly.com/question/20895732
#SPJ11
A burner was designed to use LPG whose volumetric composition is propane 60% and butane 40%, currently this burner must use C.N. (methane 100%). Find the diameter ratio between the NG injector and the fuel injector. LPG if you want to keep constant the power in the burner and the pressure of feed is the same for both gases.
The diameter ratio between the NG injector and the fuel injector is the ratio of the mass flow rates of LPG and methane. The mass flow rate of fuel must be the same for both gases.
The question is asking about the diameter ratio between the NG injector and the fuel injector when a burner was designed to use LPG whose volumetric composition is propane 60% and butane 40%, but currently, it must use C.N. (methane 100%).To solve this problem, we can use the concept of Stoichiometry. Stoichiometry is the measure of quantitative relationships of the reactants and products in a chemical reaction. It is based on the law of conservation of mass that states that mass is neither created nor destroyed in a chemical reaction.How to use stoichiometry to solve the problem?We can assume that the fuel and oxidant both reach stoichiometric conditions, which means that we have enough fuel and oxidant to ensure complete combustion of the fuel.So, we can write the stoichiometric equation for the combustion of LPG and C.N. as follows:LPG: C3H8 + 5 O2 → 3 CO2 + 4 H2O + Heat C.N.: CH4 + 2 O2 → CO2 + 2 H2O + HeatNote that for LPG, we use the volumetric composition to determine the ratio of propane to butane.
Assuming that the pressure of feed is the same for both gases, we can use the ideal gas law to convert the volumetric composition to the molar composition of LPG.Let Vp and Vb be the volumes of propane and butane, respectively. Then, we have:Vp + Vb = 1 (since the sum of the volumes is equal to 1)PVp/V = 0.6 (since the volumetric composition of propane is 60%)PVb/V = 0.4 (since the volumetric composition of butane is 40%)where P is the pressure and V is the total volume of LPG.Using the ideal gas law, we have:P V = n R Twhere n is the number of moles, R is the gas constant, and T is the temperature.
Assuming that the temperature is constant, we have:P Vp = 0.6 n R TandP Vb = 0.4 n R TDividing these two equations, we get:P Vp / P Vb = 0.6 / 0.4orVp / Vb = 3 / 2Thus, the molar ratio of propane to butane is 3 : 2. Therefore, the molar composition of LPG is:C3H8 = 3/(3+2) = 0.6 or 60% (by mole)C4H10 = 2/(3+2) = 0.4 or 40% (by mole)Now, we can calculate the amount of air needed for complete combustion of LPG and C.N. using the stoichiometric equation and assuming that the combustion is at constant pressure and temperature.We know that:1 mole of C3H8 requires 5 moles of O21 mole of C4H10 requires 6.5 moles of O21 mole of CH4 requires 2 moles of O2Therefore, the mass of air required is:For LPG: (3/5) x (2) + (2/5) x (6.5) = 3.4 moles of airFor C.N.: 2 moles of air
Since the pressure of feed is the same for both gases, the ratio of the fuel injector diameter to the NG injector diameter is given by the ratio of the mass flow rates of fuel and oxidant.For the same power output, the mass flow rate of fuel must be the same for both gases. Therefore, we have:(mass flow rate of C.N.) x (density of LPG / density of C.N.) = mass flow rate of LPGThus, the ratio of the fuel injector diameter to the NG injector diameter is:diameter ratio = (mass flow rate of LPG / density of LPG) / (mass flow rate of C.N. / density of C.N.)
The diameter ratio between the NG injector and the fuel injector is the ratio of the mass flow rates of LPG and methane. The mass flow rate of fuel must be the same for both gases.
To know more about diameter visit
https://brainly.com/question/33140251
#SPJ11
You are tasked with investigating the heat extraction form a flat plate heat exchanger. List the various variables you are expecting and classify each as dependent, independent or extraneous. Develop a experimental matrix based on these variables.
Heat extraction from a flat plate heat exchanger can be investigated by considering the various variables that affect the process. These variables can be classified into dependent, independent or extraneous variables.
The following variables are expected in the investigation: Dependent Variables: Heat extraction rate is the dependent variable in this investigation as it is directly influenced by other variables. The heat extraction rate will be measured in Watts .Independent Variables :Fluid flow rate, temperature difference and plate spacing are the independent variables in this investigation. Fluid flow rate will be measured in litres per minute. Temperature difference will be measured in degrees Celsius. Plate spacing will be measured in millimeters .Extraneous Variables:
Fluid viscosity, fluid type and fluid velocity are the extraneous variables in this investigation. Fluid viscosity will be measured in centipoise. Fluid type will be classified as either water or oil. Fluid velocity will be measured in metres per second.Experimental Matrix:The experimental matrix is based on the independent variables and their levels:Fluid Flow Rate (litres/min)Temperature Difference (°C)Plate Spacing (mm)Level 1: 2 10 4Level 2: 4 20 6Level 3: 6 30 8Level 4: 8 40 10This matrix allows for the investigation of the independent variables and their effects on the dependent variable. The extraneous variables will be controlled and kept constant throughout the investigation to ensure accurate results.
To know more about Dependent Variables visit:
brainly.com/question/32734526
#SPJ11
There is a spherical thermometer. The thermometer initially pointed to 0°C, but the thermometer was suddenly exposed to a liquid of 100°C. (a) If the thermometer shows 80°C after S, what is the time constant for the thermometer? (b) Determine the value shown on the thermometer after 1.5 s.
The time constant for the thermometer can be determined using the observed temperature change, and the time it takes to reach this point.
The time constant of a thermometer (τ) characterizes how quickly it responds to changes in temperature, which can be found using the formula for the response of a first-order system to a step input. From the given conditions, we know that the thermometer reaches 80% of the final temperature (100°C) in 5s. Using this information, the time constant τ can be computed. Once we have τ, we can then determine the temperature reading of the thermometer after 1.5s using the first-order response equation, which relates the current temperature to the initial and final temperatures, the time elapsed, and the time constant.
Learn more about [time constant] here:
https://brainly.com/question/32577767
#SPJ11
A 50 km long optical fiber link operating at 850 nm offers an average attenuation of 0.5 dB/km. An optical power of 100 μW is launched into the fiber at the input. What is the value of optical power at a distance of 30 km from the input? Also express the power in W and in dBm. What is the output power at the end of the link?
The attenuation of the optical fiber link over a distance of 30 km is 15 dB. Power in W and dBm are 3.162277660168379e-09 W and -85.0 dBm respectively
Given that :
attenuation of fiber link = 0.5distance = 30kmAttenuation over a distance of 50km would be :
30 * 0.5 = 15dBHence, attenuation over a distance of 30km is 15dB.
B.)
Output power
Power = Input power * 10^(-Attenuation/10)Power = 100 * 10^-6 * 10^(-15/10)
Power = 3.162277660168379e-09 W
Hence power in W is
Power (dBm) = 10 * log10(Power (W))
Power (dBm) = 10 * log10(3.162277660168379e-09)
Power (dBm) = -85.0 dBm
Hence, power in dBm is -85.0 dBm
Learn more on output power :https://brainly.com/question/20038729
#SPJ4