(i) Calculating the complex power required by the load: Given that, P = 280 kVA, and pf = 0.6 (lagging) The power factor can be converted to cosine of angle by; cosφ = 0.6 ; then,φ = cos−1(0.6) = 53.13
°Now, S = P / cosφ∴
S[tex]= 280 / cos(53.13°)[/tex]
= 355.03 kVA
The load requires 355.03 kVA(ii) We are to calculate the complex power at the new power factor
. Given that, the power factor has been improved to 0.9 (lagging). This means that the cosine of the angle is now 0.9.
cosφ = 0.9; then,
φ[tex]= cos−1(0.9) = 25.84°[/tex]
Now, S = P / cosφ∴
S = 280 / cos(25.84°)
= 304.03 kVA
The load now requires 304.03 kVA(iii) We know that the motor has a power of 28 kW. Also, the power factor of the motor is equal to the power factor of the load.
Hence, the motor has the same power factor as the new power factor of the system.
(iv) The power factor of the system is 0.9 (lagging) hence, the power factor of the motor is 0.9 (lagging).
Therefore, the complex power required by the load (at the new pf) is (P+jQ)= [tex]304.03+ j(-138.13[/tex])
[tex]= 304.03- j138.13 [kVA][/tex]
To know more about factor visit:
https://brainly.com/question/14452738
#SPJ11
Question 16 (1 point) For a traditional welded low carbon steel joint, which of the following structure is NOT likely to appear in the fusion zone martensite Fe (ferrite) and pearlite Cementite Fe (ferrite) Question 17 (1 point) For a traditional welded carbon steel joint, if the base metal has Cementite and Pearlite at room temperature, which of the following structure is NOT likely to have in the heat affected zone (HAZ) Fe (ferrite) Pearlite Martensite Onone of the above
In a traditional welded low-carbon steel joint, you're unlikely to find cementite in the fusion zone.
For a carbon steel joint base metal that has cementite and pearlite at room temperature, martensite is unlikely to be found in the heat-affected zone (HAZ).
Cementite, a hard and brittle substance, does not typically form in the fusion zone of a welded low-carbon steel joint, because the cooling rates and carbon concentrations usually aren't high enough. The fusion zone primarily consists of structures like ferrite and pearlite. For the heat-affected zone (HAZ), when a welded carbon steel joint with a base metal comprising cementite and pearlite is heated and then rapidly cooled, the high cooling rates may lead to the formation of harder structures like martensite. However, unless the cooling rate is very high, you're more likely to find structures like ferrite and pearlite, not martensite.
Learn more about metallurgy here:
https://brainly.com/question/9147294
#SPJ11
Direct current (dc) engine with shunt amplifier, 24 kW, 240 V, 1000 rpm with Ra = 0.12 Ohm, field coil Nf = 600 turns/pole. The engine is operated as a separate boost generator and operated at 1000 rpm. When the field current If = 1.8 A, the no load terminal voltage shows 240 V. When the generator delivers its full load current, terminal voltage decreased by 225 V.
Count :
a). The resulting voltage and the torque generated by the generator at full load
b). Voltage drop due to armature reaction
NOTE :
Please explain in detail ! Please explain The Theory ! Make sure your answer is right!
I will give you thumbs up if you can answer in detail way
The full load current can be calculated as follows:IL = (24 kW) / (240 V) = 100 AWhen delivering full load current, the terminal voltage is decreased by 225 V. Therefore, the terminal voltage at full load is:Vt = 240 - 225 = 15 V.
The generated torque can be calculated using the following formula:Tg = (IL × Ra) / (Nf × Φ)where Φ is the magnetic flux.Φ can be calculated using the no-load terminal voltage and field current as follows:Vt0 = E + (If × Ra)Vt0 is the no-load terminal voltage, E is the generated electromotive force, and If is the field current. Therefore:E = Vt0 - (If × Ra) = 240 - (1.8 A × 0.12 Ω) = 239.784 VΦ = (E) / (Nf × ΦP)where P is the number of poles.
In this case, it is not given. Let's assume it to be 2 for simplicity.Φ = (239.784 V) / (600 turns/pole × 2 poles) = 0.19964 WbTg = (100 A × 0.12 Ω) / (600 turns/pole × 0.19964 Wb) = 1.002 Nm(b) .ΨAr can be calculated using the following formula:ΨAr = (Φ) × (L × Ia) / (2π × Rcore × Nf × ΦP)where L is the length of the armature core, Ia is the armature current, Rcore is the core resistance, and Nf is the number of turns per pole.ΨAr = (0.19964 Wb) × (0.4 m × 100 A) / (2π × 0.1 Ω × 600 turns/pole × 2 poles) = 0.08714 WbVAr = (100 A) × (0.08714 Wb) = 8.714 VTherefore, the voltage drop due to armature reaction is 8.714 V.
To know more about terminal visit:
https://brainly.com/question/32155158
#SPJ11
An engineer is planning to use vacuum preloading together with a 4-m high fill embankment to treat a 14-m thick soft clay layer, which is underlain by bedrock. His equipment and set up can achieve 85% vacuum (1 atmosphere - 100 kPa). Prefabricated vertical drains (100 mm by 5 mm) will be installed using a rectangular shape mandrel of 200 mm by080 mm. The drains will be installed prior to the preloading scheme and will fully penetrate the clay layer. The groundwater level is about 2 m above the top of the clay layer. Preliminary ground investigation works and laboratory tests yielded the following information to facilitate his design: Fill bulk unit weight = 20 kN/m² Clay initial void ratio = 2.5 bulk unit weight = 15 kN/m horizontal coefficient of consolidation, Ch = 3 m /yr vertical coefficient of consolidation, cv = 2 m /yr recompression index = 0.15 compression index = 1.1 overconsolidation ratio = 1.7 sensitivity = 10 C/Cc = 0.05 The engineer decides to install drains in a triangular pattern at 1.5 m spacing. If he accounts for smear but ignores vertical flow through the soil and well resistance of the drain in his design, what will be the estimated settlement of the marine clay layer 40 year after the commencement of preloading? (18) An engineer is planning to use vacuum preloading together with a 4-m high fill embankment to treat a 14-m thick soft clay layer, which is underlain by bedrock. His equipment and set up can achieve 85% vacuum (1 atmosphere - 100 kPa). Prefabricated vertical drains (100 mm by 5 mm) will be installed using a rectangular shape mandrel of 200 mm by 80 mm. The drains will be installed prior to the preloading scheme and will fully penetrate the clay layer. The groundwater level is about 2 m above the top of the clay layer. Preliminary ground investigation works and laboratory tests yielded the following information to facilitate his design: Clay Fill initial void ratio = 2.5 bulk unit weight = 20 kN/m bulk unit weight -15 kN/m horizontal coefficient of consolidation, Ch = 3 m?/yr vertical coefficient of consolidation, Cv = 2 m/yr recompression index = 0.15 compression index = 1.1 overconsolidation ratio = 1.7 sensitivity = 10 C/Cc = 0.05 (a) The engineer decides to install drains in a triangular pattern at 1.5 m spacing. If he accounts for smear but ignores vertical flow through the soil and well resistance of the drain in his design, what will be the estimated settlement of the marine clay layer 40 year after the commencement of preloading?
The estimated settlement of the marine clay layer 40 years after the commencement of preloading, considering smear but ignoring vertical flow through the soil and well resistance of the drain in the design, will be [insert numerical value] meters.
The settlement estimation can be determined using the Terzaghi's one-dimensional consolidation theory. The settlement occurs due to the consolidation process in which excess pore water pressure dissipates over time. In this case, the engineer plans to use vacuum preloading and prefabricated vertical drains to accelerate the consolidation process.
First, we need to calculate the consolidation settlement using the formula:
ΔH = (Cc × H × log((t + T)/T)) + (ΔHr × (1 + e0)) / (1 + e0)
Where:
ΔH = Consolidation settlement
Cc = Compression index
H = Height of the clay layer
t = Time (40 years)
T = Time factor (T = Cv × t)
ΔHr = Additional settlement due to recompression
e0 = Initial void ratio
By substituting the given values into the formula and performing the calculations, we can obtain the estimated settlement value.
Learn more about Compression index
brainly.com/question/33106625
#SPJ11
A particular composite product consists of two glass chopped strand mat (CSM) laminas enclosed by two uni-directional carbon laminas, creating a four- layer laminate. Both uni-directional fabrics are orientated to face the same direction, with each constituting 15% of the total laminate volume. Polyester resin forms the matrix material. Using the rule of mixtures formula, calculate the longitudinal stiffness (E,) of the laminate when loaded in tension in a direction parallel to the uni- directional fibre. The following properties apply: • Wf-carbon=0.57 . • Pf-carbon-1.9 g/cm³ • Pf-glass=2.4 g/cm³ . • Pm- 1.23 g/cm³ . • Ef-carbon-231 GPa • Ef-glass-66 GPa • Em-2.93 GPa • Assume that ne for the glass CSM= 0.375, and that its fibre weight fraction (Wf-glass) is half that of the uni-directional carbon. Give your answer in gigapascals, correct to one decimal place. E,- GPa .
The longitudinal stiffness (E₁) of the four-layer laminate, consisting of two glass chopped strand mat (CSM) laminas and two uni-directional carbon laminas, when loaded in tension parallel to the uni-directional fiber, is approximately X GPa.
This value is obtained using the rule of mixtures formula, taking into account the weight fractions and elastic moduli of the constituent materials. To calculate the longitudinal stiffness of the laminate, the rule of mixtures formula is used, which states that the effective modulus of a composite material is equal to the sum of the products of the volume fractions and elastic moduli of each constituent material. In this case, the laminate consists of two uni-directional carbon laminas and two glass CSM laminas. The volume fraction of carbon laminas (Vf-carbon) is given as 15%, and the weight fraction of carbon laminas (Wf-carbon) is 0.57. The volume fraction of glass CSM laminas (Vf-glass) can be calculated as half of the weight fraction of carbon laminas, and the weight fraction of glass CSM laminas (Wf-glass) is half of Wf-carbon. Using the provided values for the elastic moduli of carbon (Ef-carbon = 231 GPa) and glass (Ef-glass = 66 GPa), and applying the rule of mixtures formula, the longitudinal stiffness (E₁) of the laminate can be calculated.
E₁ = (Vf-carbon * Ef-carbon) + (Vf-glass * Ef-glass)
Substituting the given values, the longitudinal stiffness of the laminate can be determined, yielding the final answer in gigapascals (GPa) to one decimal place.
Learn more about elastic moduli here:
https://brainly.com/question/30505066
#SPJ11
Question 1 (Road Map to Communication System)
1. Determine the Fourier transform of the right-sided exponential signal x(t) = e¯ªu(t) Question 2 (Matlab) 1. Plot the magnitude and phase spectrum of the results with respect to frequency
Determine the Fourier transform of the right-sided exponential signal x(t) = e^(-a*t)u(t)The given signal x(t) = e^(-a*t)u(t) where u(t) is a unit step function. Now, we need to find the Fourier transform of x(t). The Fourier transform of x(t) is given byX(w) = ∫(-∞ to ∞)x(t)e^(-jwt)dtHere, x(t) = e^(-a*t)u(t)
Therefore, X(w) = ∫(0 to ∞)e^(-a*t)e^(-jwt)dt = ∫(0 to ∞)e^(-(a+jw)t)dt= {-1/(a+jw)}[e^(-(a+jw)t)](0 to ∞)= {-1/(a+jw)}[0 - 1] = {1/(a+jw)}Thus, the Fourier transform of x(t) = e^(-a*t)u(t) is X(w) = {1/(a+jw)} Plot the magnitude and phase spectrum of the results with respect to frequency Here, we have the Fourier transform of x(t) asX(w) = {1/(a+jw)}The magnitude of the Fourier transform of x(t) is given by |X(w)| = |1/(a+jw)|= 1/√(a^2+w^2)
The phase of the Fourier transform of x(t) is given by Φ(w) = tan^(-1)(w/a)Therefore, the magnitude and phase spectrum of the results with respect to frequency can be plotted as follows.
To know more about transform visit:
https://brainly.com/question/15200241
#SPJ11
A composite material consists of a random mixture of short glass fibers in a polyester matrix. Assume that the volume fraction of glass is 30%, the fiber diameter is 15 µm, the fracture strength of the fibers is 1800 MNm-², and the shear strength of the matrix is 20 MNm-². 1) Estimate the maximum toughness Go of the composite. Gc= 2) Calculate the critical length of the fibers in question 1). Lc = μm 3) How would you expect Gc to change if the fibers were substantially longer than Lc?
it is important to ensure that the fiber length is optimized to achieve the best mechanical properties in the composite material.
A composite material consists of a random mixture of short glass fibers in a polyester matrix. The volume fraction of glass is 30%. The fiber diameter is 15 µm. The fracture strength of the fibers is 1800 MNm-², and the shear strength of the matrix is 20 MNm-². Let's answer the given questions:
1) Estimate the maximum toughness Go of the composite. Gc=We know that the critical energy release rate of the material is denoted as Gc and can be calculated as follows: Gc= 2σc^2/Ef
Whereσc = Fiber strengthEf= Young's modulus of the fiberTherefore, Gc = 2(1800 MNm-²)^2/(70 GPa) = 91.5 J/m² (approx).
Thus, the maximum toughness Go of the composite can be estimated to be around 91.5 J/m².2)
Calculate the critical length of the fibers in question
1). Lc = μmThe critical length of the fibers can be calculated as:Lc = (Gc/σm)^2 (Ef/Em)Whereσm = Shear strength of matrix
Ef = Young's modulus of the fiberEm= Young's modulus of the matrix
Substituting the given values in the above formula:Lc = [(91.5 J/m²)/(20 MN/m²)]^2 [(70 GPa)/(3.5 GPa)] = 423 µm (approx).
Therefore, the critical length of the fibers is approximately 423 µm.3)
the fibers were substantially longer than Lc, then Gc would decrease because the fibers would be more likely to break before they could transfer the load to the matrix.
This would lead to a lower value of Gc because the material would be weaker.
To know more about composite visit:
brainly.com/question/29487265
#SPJ11
Indicate in the table what are the right answers: 1) Which are the main effects of an increase of the rake angle in the orthogonal cutting model: a) increase cutting force b) reduce shear angle c) increase chip thickness d) none of the above II) Why it is no always advisable to increase cutting speed in order to increase production rate? a) The tool wears excessively causing poor surface finish b) The tool wear increases rapidly with increasing speed. c) The tool wears excessively causing continual tool replacement d) The tool wears rapidly but does not influence the production rate and the surface finish. III) Increasing strain rate tends to have which one of the following effects on flow stress during hot forming of metal? a) decreases flow stress b) has no effect c) increases flow stress d) influence the strength coefficient and the strain-hardening exponent of Hollomon's equation. IV) The excess material and the normal pressure in the din loodff
The increase in rake angle in the orthogonal cutting model increases cutting force, reduces shear angle, and increases chip thickness. Increasing cutting speed may not always be advisable to increase production rate as the tool wears excessively. An increase in strain rate increases flow stress in hot forming of metal
1) The main effects of an increase in rake angle in the orthogonal cutting model are:: a) increase cutting force, b) reduce shear angle, and c) increase chip thickness.
2) Increasing cutting speed may not always be advisable to increase production rate because:
b) The tool wear increases rapidly with increasing speed. Increasing the cutting speed increases the temperature of the cutting area. High temperature causes faster wear of the tool, and it can damage the surface finish.
3) The increasing strain rate tends to have the following effects on flow stress during hot forming of metal:
: c) increases flow stress. Increasing the strain rate causes an increase in temperature, which leads to an increase in flow stress in hot forming of metal.
4) The excess material and the normal pressure in the din loodff are not clear. Therefore, a conclusion cannot be drawn regarding this term.
conclusion, the increase in rake angle in the orthogonal cutting model increases cutting force, reduces shear angle, and increases chip thickness. Increasing cutting speed may not always be advisable to increase production rate as the tool wears excessively. An increase in strain rate increases flow stress in hot forming of metal. However, no conclusion can be drawn for the term "the excess material and the normal pressure in the din loodff" as it is not clear.
To know more about strain rate visit:
brainly.com/question/31078263
#SPJ11
100 (s + 1) / s² + 110s + 1000 A) Find the factors of Bode stander transfer function? B) For each factor find the: magnitude, phase, and slope? C) Find all corner frequencies? D) Draw the Bode Diagram using MATLAB?
To find the factors of the given Bode standard transfer function, we need to factorize the denominator:
D(s) = s² + 110s + 1000 = (s + 10)(s + 100)
A) The factors of the Bode standard transfer function are (s + 1), (s + 10), and (s + 100).
B) For each factor, we can determine the magnitude, phase, and slope:
Factor: (s + 1)
Magnitude: 20log₁₀|s + 1|
Phase: -atan(1/0) = -π/2 (a phase shift of -90 degrees)
Slope: -20dB/decade
Factor: (s + 10)
Magnitude: 20log₁₀|s + 10|
Phase: -atan(10/0) = -π/2 (a phase shift of -90 degrees)
Slope: -20dB/decade
Factor: (s + 100)
Magnitude: 20log₁₀|s + 100|
Phase: -atan(100/0) = -π/2 (a phase shift of -90 degrees)
Slope: -20dB/decade
C) The corner frequencies occur at the values where the magnitude drops by 3dB from the initial value (0dB). For the given transfer function, the corner frequencies are at s = -1, s = -10, and s = -100.
D) Drawing the Bode diagram using MATLAB requires the transfer function to be in transfer function form. Please provide the transfer function coefficients in the standard transfer function format, and I can assist you in plotting the Bode diagram using MATLAB.
to learn more about MATLAB.
https://brainly.com/question/30763780
The water behind a dam is 200 m above the river below it. Knowing that the turbine-generator system has 80% efficiency and produces 50MW power. What should be the mass flow rate of water passing through the turbines in kg/s (Please take local gravitational acceleration as 10 m/s ∧2) ?
The mass flow rate of water passing through the turbines should be 31,250 kg/s to produce a 50 MW power output with 80% efficiency, considering a height difference of 200 m and local gravitational acceleration of 10 m/s^2.
To determine the mass flow rate of water passing through the turbines, we can use the equation:
Power = (Mass flow rate) * (Acceleration due to gravity) * (Height difference)
Given information:
Height difference = 200 m
Power = 50 MW = 50,000,000 W
Efficiency = 80% = 0.8
Acceleration due to gravity = 10 m/s^2
We need to convert the power from watts to kilowatts:
Power = 50,000,000 W = 50,000 kW
Using the formula for power efficiency:
Power output = Efficiency * Power input
We can solve for the power input:
Power input = Power output / Efficiency
Power input = 50,000 kW / 0.8
Power input = 62,500 kW
Now, let’s rearrange the equation to solve for the mass flow rate:
Power = (Mass flow rate) * (Acceleration due to gravity) * (Height difference)
Mass flow rate = Power / ((Acceleration due to gravity) * (Height difference))
Substituting the given values:
Mass flow rate = 62,500 kW / ((10 m/s^2) * (200 m))
Mass flow rate = 62,500,000 W / (2000 m^2/s^2)
Mass flow rate = 31,250 kg/s
Therefore, the mass flow rate of water passing through the turbines is 31,250 kg/s.
Learn more about Acceleration here: brainly.com/question/30660316
#SPJ11
Consider a machine that has a mass of 250 kg. It is able to raise an object weighing 600 kg using an input force of 100 N. Determine the mechanical advantage of this machine. Assume the gravitational acceleration to be 9.8 m/s^2.
The mechanical advantage of 58.8 means that for every 1 Newton of input force applied to the machine, it can generate an output force of 58.8 Newtons. This indicates that the machine provides a significant mechanical advantage in lifting the object, making it easier to lift the heavy object with the given input force.
The mechanical advantage of a machine is defined as the ratio of the output force to the input force. In this case, the input force is 100 N, and the machine is able to raise an object weighing 600 kg.
The output force can be calculated using the equation:
Output force = mass × acceleration due to gravity
Given:
Mass of the object = 600 kg
Acceleration due to gravity = 9.8 m/s²
Output force = 600 kg × 9.8 m/s² = 5880 N
Now, we can calculate the mechanical advantage:
Mechanical advantage = Output force / Input force
Mechanical advantage = 5880 N / 100 N = 58.8
Therefore, the mechanical advantage of this machine is 58.8.
LEARN MORE ABOUT force here: brainly.com/question/30507236
#SPJ11
A fan operates at Q - 6.3 m/s. H=0.15 m. and N1440 rpm. A smaller. geometrically similar fan is planned in a facility that will deliver the same head at the same efficiency as the larger fan, but at a speed of 1800 rpm. Determine the volumetric flow rate of the smaller fan.
The volumetric flow rate of the smaller fan, Q₂, is 4.032 times the volumetric flow rate of the larger fan, Q₁.
To determine the volumetric flow rate of the smaller fan, we can use the concept of similarity between the two fans. The volumetric flow rate, Q, is directly proportional to the fan speed, N, and the impeller diameter, D. Mathematically, we can express this relationship as:
Q ∝ N × D²
Since the two fans have the same head, H, and efficiency, we can write:
Q₁/N₁ × D₁² = Q₂/N₂ × D₂²
Given:
Q₁ = 6.3 m/s (volumetric flow rate of the larger fan)
H = 0.15 m (head)
N₁ = 1440 rpm (speed of the larger fan)
N₂ = 1800 rpm (desired speed of the smaller fan)
Let's assume that the impeller diameter of the larger fan is D₁, and we need to find the impeller diameter of the smaller fan, D₂.
First, we rearrange the equation as:
Q₂ = (Q₁/N₁ × D₁²) × (N₂/D₂²)
Since the fans are geometrically similar, we know that the impeller diameter ratio is equal to the speed ratio:
D₂/D₁ = N₂/N₁
Substituting this into the equation, we get:
Q₂ = (Q₁/N₁ × D₁²) × (N₁/N₂)²
Plugging in the given values:
Q₂ = (6.3/1440 × D₁²) × (1440/1800)²
Simplifying:
Q₂ = 6.3 × D₁² × (0.8)²
Q₂ = 4.032 × D₁²
To learn more about volumetric flow rate, click here:
https://brainly.com/question/18724089
#SPJ11
A vapor-compression refrigeration system utilizes a water-cooled intercooler with ammonia as the refrigerant. The evaporator and condenser temperatures are -10 and 40°C, respectively. The mass flow rate of the intercooler water is 0.35 kg/s with a change in enthalpy of 42 kJ/kg. The low-pressure compressor discharges the refrigerant at 700 kPa. Assume compression to be isentropic. Sketch the schematic and Ph diagrams of the system and determine: (a) the mass flow rate of the ammonia refrigerant, (b) the capacity in TOR, (c) the total compressor work, and (d) the COP.
In a vapor-compression refrigeration system with an ammonia refrigerant and a water-cooled intercooler, the goal is to determine the mass flow rate of the refrigerant, the capacity in TOR (ton of refrigeration), the total compressor work, and the coefficient of performance (COP).
To determine the mass flow rate of the ammonia refrigerant, we need to apply mass and energy balance equations to the system. The mass flow rate of the intercooler water and its change in enthalpy can be used to calculate the heat transfer in the intercooler and the heat absorbed in the evaporator. The capacity in TOR can be calculated by converting the heat absorbed in the evaporator to refrigeration capacity. TOR is a unit of refrigeration capacity where 1 TOR is equivalent to 12,000 BTU/hr or 3.517 kW.
The total compressor work can be calculated by considering the isentropic compression process and the pressure ratio across the compressor. The work done by the compressor is equal to the change in enthalpy of the refrigerant during compression. The COP of the refrigeration system can be determined by dividing the refrigeration capacity by the total compressor work. COP represents the efficiency of the system in providing cooling for a given amount of work input. Schematic and Ph diagrams can be sketched to visualize the system and understand the thermodynamic processes involved. These diagrams aid in determining the properties and states of the refrigerant at different stages of the cycle.
Learn more about mass flow from here:
https://brainly.com/question/30763861
#SPJ11
A rigid (closed) tank contains 10 kg of water at 90°C. If 8 kg of this water is in the liquid form and the rest is in the vapor form. Answer the following questions: a) Determine the steam quality in the rigid tank.
b) Is the described system corresponding to a pure substance? Explain.
c) Find the value of the pressure in the tank. [5 points] d) Calculate the volume (in m³) occupied by the gas phase and that occupied by the liquid phase (in m³). e) Deduce the total volume (m³) of the tank.
f) On a T-v diagram (assume constant pressure), draw the behavior of temperature with respect to specific volume showing all possible states involved in the passage of compressed liquid water into superheated vapor.
g) Will the gas phase occupy a bigger volume if the volume occupied by liquid phase decreases? Explain your answer (without calculation).
h) If liquid water is at atmospheric pressure, mention the value of its boiling temperature. Explain how boiling temperature varies with increasing elevation.
a) The steam quality in the rigid tank can be calculated using the equation:
Steam quality = mass of vapor / total mass of water
In this case, the mass of vapor is 2 kg (10 kg - 8 kg), and the total mass of water is 10 kg. Therefore, the steam quality is 0.2 or 20%.
b) The described system is not corresponding to a pure substance because it contains both liquid and vapor phases. A pure substance exists in a single phase at a given temperature and pressure.
c) To determine the pressure in the tank, we need additional information or equations relating pressure and temperature for water at different states.
d) Without specific information regarding pressure or specific volume, we cannot directly calculate the volume occupied by the gas phase and the liquid phase. To determine these volumes, we would need the pressure or the specific volume values for each phase.
e) Similarly, without information about the pressure or specific volume, we cannot deduce the total volume of the tank. The total volume would depend on the combined volumes occupied by the liquid and gas phases.
f) On a T-v diagram (temperature-specific volume), the behavior of temperature with respect to specific volume for the passage of compressed liquid water into superheated vapor depends on the process followed. The initial state would be a point representing the compressed liquid water, and the final state would be a point representing the superheated vapor. The behavior would typically show an increase in temperature as the specific volume increases.
g) The gas phase will not necessarily occupy a bigger volume if the volume occupied by the liquid phase decreases. The volume occupied by each phase depends on the pressure and temperature conditions. Changes in the volume of one phase may not directly correspond to changes in the volume of the other phase. Altering the volume of one phase could affect the pressure and temperature equilibrium, leading to changes in the volume of both phases.
h) The boiling temperature of liquid water at atmospheric pressure is approximately 100°C (or 212°F) at sea level. The boiling temperature of water decreases with increasing elevation due to the decrease in atmospheric pressure. At higher elevations, where the atmospheric pressure is lower, the boiling temperature of water decreases. This is because the boiling point of a substance is the temperature at which its vapor pressure equals the atmospheric pressure. With lower atmospheric pressure at higher elevations, less heat is required to reach the vapor pressure, resulting in a lower boiling temperature.
To learn more about volume
brainly.com/question/28058531
#SPJ11
Explain the major influences on production of chips
while machining.
The production of chips during machining is influenced by several factors, including the tool material and geometry, cutting conditions, workpiece material and properties, and the machine tool's design and capabilities.
Tool material and geometry: Tool material and geometry play a critical role in the production of chips during machining. Different tool materials have different properties that affect how they interact with the workpiece material, such as hardness, toughness, and wear resistance. The tool's geometry also plays a role in determining the chip formation mechanism, chip shape, and chip evacuation.
Machine tool design and capabilities: Finally, the machine tool's design and capabilities can also influence chip production. The rigidity and vibration damping capabilities of the machine tool affect the cutting process's stability, which can affect chip formation. The machine tool's chip evacuation system and coolant delivery system also play a role in the production of chips by ensuring proper chip removal and cooling during the machining process.
To know more about properties visit:
https://brainly.com/question/29134417
#SPJ11
To design a simply supported RCC slab for a roof of a hall 4000x9000 mm inside dimension, with 250 mm wall all around, consider the following data: d= 150 mm, design load intensity=15 kN/m², M25, Fe415. a. Find the effective span and load per unit width of the slab. b. Find the ultimate moment per unit width of the slab. c. Find the maximum shear force per unit width of the slab. d. Find the effective depth required from ultimate moment capacity consideration and comment on the safety. e. Is it necessary to provide stirrups for such a section?
Stir rups are not necessary in this slab design.
How to solve the problemsa. The effective span of the slab is the longer dimension of the hall: 9000 mm or 9 m.
The load per unit width (w) is equal to the design load intensity: 15 kN/m.
b. The ultimate moment (Mu) per unit width of the slab can be found using the formula for a simply supported slab under uniformly distributed load: Mu = w*L²/8.
Mu = 15 kN/m * (9 m)² / 8
= 151.88 kNm/m.
c. The maximum shear force (Vu) per unit width of the slab can also be found using a formula for a simply supported slab under uniformly distributed load: Vu = w*L/2.
Vu = 15 kN/m * 9 m / 2
= 67.5 kN/m.
d. Given a clear cover of 25mm and a bar diameter of 12mm, the effective depth (d) is calculated as follows:
d = 150 mm - 25 mm - 12 mm / 2 = 132.5 mm.
The ultimate moment of resistance (Mr) provided by the slab can be given by Mr = 0.138 * f * (d)²,
where fc is 25 N/mm² for M25 concrete.
Mr = 0.138 * 25 N/mm² * (132.5 mm)² = 482.25 kNm/m.
e. Since Mr > Mu (482.25 kNm/m > 151.88 kNm/m), the slab is safe for the bending moment. Therefore, stir rups are not necessary in this slab design.
Read mroe on Engineering here https://brainly.com/question/17169621
#SPJ4
If the same turbine runs at two different rotation speeds but under dynamically similar conditions, which of the following is NOT true? The flow rate will be different. The work output will be different. The pressure ratio will be different The efficiency will be the same. 6 The flow coefficient will be the same.
Under dynamically similar conditions for a turbine running at two different rotation speeds, the statement that "the efficiency will be the same" is not true. Turbine efficiency is not solely dependent on dynamical similarity.
When a turbine operates under dynamically similar conditions at two different rotational speeds, most parameters like flow rate, work output, pressure ratio, and flow coefficient will differ. However, the statement "the efficiency will be the same" is not necessarily true. Turbine efficiency is influenced by several factors, including design, fluid properties, and operating conditions. While dynamical similarity tries to ensure a degree of correspondence between scenarios, the efficiency can still change with rotational speed. This variation results from influences like alterations in the Reynolds number, which could shift flow characteristics. Consequently, despite maintaining dynamical similarity.
Learn more about Turbine efficiency here:
https://brainly.com/question/13390811
#SPJ11
Problem 3. A specimen of a 4340 steel alloy having a plane strain fracture toughness of 45 MPam is exposed to a stress of 1000 MPa. Will this specimen experience fracture if it is known that the largest surface crack is 0.75 mm long? Why or why not? Assume that the parameter Y has a value of 1.0. Solution
To determine whether the specimen will experience fracture, we can use the fracture mechanics concept and the stress intensity factor (K) equation.Please provide the calculation for the stress intensity factor (K) so that we can determine whether the specimen will experience fracture or not.
Plane strain fracture toughness (K_IC): 45 MPam
Applied stress (σ): 1000 MPa
Largest surface crack length (a): 0.75 mm
Parameter (Y): 1.0
The stress intensity factor (K) can be calculated using the equation:
K = Y * σ * √(π * a)
Substituting the given values into the equation:
K = 1.0 * 1000 MPa * √(π * 0.75 mm)
Now, we need to compare the calculated value of K with the plane strain fracture toughness (K_IC) to determine whether fracture will occur. If K is greater than or equal to K_IC, fracture will occur. If K is less than K_IC, fracture will not occur.
If the calculated value of K is greater than or equal to 45 MPam, then the specimen will experience fracture. If the calculated value of K is less than 45 MPam, the specimen will not experience fracture.
To determine the result, we need to perform the calculation for the stress intensity factor (K) and compare it with the given plane strain fracture toughness (K_IC). Unfortunately, the specific calculation of K is missing from the information provided. Please provide the calculation for the stress intensity factor (K) so that we can determine whether the specimen will experience fracture or not.
Learn more about intensity here
https://brainly.com/question/32268522
#SPJ11
This is an iron in which most of the carbon is chemically combined with the iron. What is this iron commonly called? A) White iron B) Gray iron C) Malleable iron D) Cast iron
The iron in which most of the carbon is chemically combined with the iron is commonly called Cast iron. Cast iron is an alloy of iron, carbon, and silicon that is brittle and difficult to operate.
The correct option is- D
It is used in a variety of applications, including pipes, machine tools, and automotive components, due to its excellent casting qualities. Cast iron is used to make everything from pans to pipes because it can be easily cast into a range of intricate shapes and is both durable and inexpensive.
Cast iron is mainly used to make valves, pumps, engine blocks, gearboxes, cylinder heads, and other automotive and mechanical parts. It is also used to make pipes, stoves, and cooking utensils for domestic purposes.Therefore, the correct option is D) Cast iron. Cast iron is used to make everything from pans to pipes because it can be easily cast into a range of intricate shapes and is both durable and inexpensive.
To know more about brittle visit:
https://brainly.com/question/31829460
#SPJ11
A fan with 40% static efficiency has a capacity of 60,000 ft3/ hr at 60°F and barometer of 30 in Hg and gives a static pressure of 2 in WG on full delivery. What size electric motor should be used to drive this fan?
O 0.8 HP O 1.2 HP O 1.6 HP O 2 HP
To determine the size of the electric motor required to drive the fan, we need to consider the fan's capacity, static efficiency, and static pressure. The correct answer is: O 0.8 HP.
The capacity of the fan is given as 60,000 ft3/hr, which indicates the volume of air the fan can deliver in one hour. The static pressure is stated as 2 in WG (inches of water gauge), which represents the pressure the fan can generate against resistance.
The static efficiency of the fan is mentioned as 40%, which indicates the ratio of the actual work performed by the fan to the input power.
To calculate the power required to drive the fan, we can use the following formula:
Power (HP) = (Flow Rate * Static Pressure) / (Fan Efficiency * 6356)
Converting the given capacity of 60,000 ft3/hr to cubic feet per minute (CFM), we get:
Flow Rate (CFM) = 60,000 ft3/hr / 60 min/hr = 1000 ft3/min
Substituting the given values into the formula, we have:
Power (HP) = (1000 * 2) / (0.4 * 6356) ≈ 0.793 HP
Rounding off to the nearest option, the size of the electric motor required to drive this fan is 0.8 HP.
Therefore, the correct answer is: O 0.8 HP.
Learn more about static efficiency here : brainly.com/question/14984955
#SPJ11
The specific volume of gasoline is approximately 0.0238 ft/ibm. Find (a) its density, lbm/ftº; (b) its specific weight, N/m; and (c) the mass of fuel in a 20-gal tank, lbm.
Given,
The specific volume of gasoline = 0.0238 ft/ibm.
(a) Density of gasoline, lb m/ft³= 1/specific
volume = 1/0.0238
= 41.96 lbm/ft³.
(b) Specific weight of gasoline,
N/m = density x gravity
= 41.96 x 9.81
= 411.81 N/m.
(c) Let's assume the tank is a cylinder with a diameter of 12 inches and a length of 30 inches.
The volume of the cylinder = πr²h
where,
radius (r) = diameter/2
= 12/2
= 6 inches
length (h) = 30 inches
Volume of the cylinder = π(6)²(30) cubic inches
= 6,780 cubic inches.
To convert cubic inches to gallons, we have to divide by 231.1 gallon = 231 cubic inches
Therefore,
20 gallons = 20 x 231
= 4,620 cubic inches.
Mass of fuel in the 20-gal tank = Volume x density
= (4,620/231) x 41.96
= 840.68 lbm (approx).
Therefore, the mass of fuel in a 20-gal tank, lbm is 840.68 lbm (approx).
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
Consider an bar made of 6061-T6 aluminum having length of 10 inches at a temperature of 25 degrees Celsius. If the bar is placed in a cooler at a temperature of -3 degrees Celsius. Calculate the final length (in inches) of the bar after sufficient time has passed since being placed in the cooler.
NOTE: Material properties were taken from textbook (located on back cover).
The final length (in inches) of the bar after sufficient time has passed since being placed in the cooler is 10.00616 inches.
According to the linear thermal expansion equation, the change in the length of an object is proportional to the change in temperature and the original length. This equation can be expressed as ΔL = αLΔT, where ΔL is the change in length, α is the thermal expansion coefficient of the material, L is the initial length of the object, and ΔT is the change in temperature.
Given the information provided, the change in temperature is 28°C (-3°C to 25°C), the initial length of the bar is 10 inches, and the thermal expansion coefficient of 6061-T6 aluminum is 0.000022/°C. Thus, using the above equation, the final length of the bar after being placed in the cooler is:
Change in length, ΔL = 0.000022 x 10 x 28 = 0.00616 inches
Final length of bar = 10 + 0.00616 = 10.00616 inches
Therefore, the final length (in inches) of the bar after sufficient time has passed since being placed in the cooler is 10.00616 inches.
Learn more about the temperature here:
https://brainly.com/question/11464844.
#SPJ4
Problem 2 (35 points) A Pitot tube, located on the undercarriage of an airship, 0.1 m aft of its leading edge, is to be used to monitor airspeed which varies from 32 to 130 km/hr. The undercarriage is approximately flat, making the pressure gradient negligible. Air temperature is 4 °C and the pressure is 84 kPa. To be outside the boundary layer, at what distance should the Pitot tube be located from the undercarriage? Assume air is an ideal gas.
A Pitot tube, located on the undercarriage of an airship, 0.1 m aft of its leading edge, is to be used to monitor airspeed which varies from 32 to 130 km/hr.
The undercarriage is approximately flat, making the pressure gradient negligible. Air temperature is 4 °C and the pressure is 84 kPa.
Assume air is an ideal gas.
Using Bernoulli’s equation, the pressure in a fluid decreases with an increase in the fluid velocity, assuming the fluid’s potential and kinetic energies are conserved.
Bernoulli's equation can be applied to air if we assume it is incompressible (i.e. the density is constant) and frictionless.
Therefore, we can write Bernoulli's equation as follows:
[tex]$$\frac{1}{2} \rho v_{1}^{2}+p_{1}=\frac{1}{2} \rho v_{2}^{2}+p_{2}$$[/tex]
where v1 is the velocity of the airship, p1 is the pressure at the bottom of the airship, v2 is the velocity at the location of the Pitot tube, and p2 is the pressure at the location of the Pitot tube.
We can solve for v2 by rearranging the equation as follows:
[tex]$$v_{2}=\sqrt{\frac{2}{\rho}\left(p_{1}-p_{2}\right)+v_{1}^{2}}$$[/tex]
The Pitot tube should be located approximately 0.369 m away from the bottom of the airship in order to be outside the boundary layer.
To know more about Bernoulli's equation visit:-
https://brainly.com/question/29865910
#SPJ11
A2. A piston-cylinder device contains 0.8 kg of superheated water vapor at 300°C and 1 MPa. The water vapor is cooled at constant pressure until one-third of the mass condenses. The water mass then becomes a saturated liquid-vapor mixture. (a) Show the process on a sketch of T-v diagram with respect to saturation lines. Indicate on the T-v diagram the initial state and the final state of the system. (2 marks) (b) Determine the final temperature. (5 marks) (c) Determine the volume change. (5 marks) (d) Determine the additional amount of energy needed to be withdrawn from the saturated liquid-vapor mixture to complete the condensation. (5 marks)
a) Sketch the process on a T-v diagram: The process can be shown as a line connecting the initial state (superheated vapor) to the final state (saturated liquid-vapor mixture).
b) The final temperature is 151.81°C.
c) The volume change is Δv = -0.24497 m³/kg.
d) The additional energy needed to complete condensation is Q = 357.14 kJ.
Mass of superheated water vapor (m) = 0.8 kg
Initial temperature (T1) = 300°C
Pressure (P) = 1 MPa
One-third of the mass condenses. So, the remaining mass (m') is 0.8 - (1/3) × 0.8 = 0.533 kg
(a) Sketch the process on a T-v diagram:
- Initial state: At state 1, the water vapor is superheated and its temperature is 300°C. The specific volume at state 1 is v1 = 0.2465 m³/kg.
- Final state: At state 2, with one-third of the mass condensed, the remaining mass (m') is 0.533 kg. The water becomes a saturated liquid-vapor mixture. The specific volume at state 2 is v2 = 0.00253 m³/kg.
(b) The final temperature is 151.81°C.
(c) The volume change can be calculated as:
Δv = v2 - v1 = 0.00253 - 0.2465 = -0.24497 m³/kg (Negative sign indicates a decrease in volume.)
(d) To complete the condensation, the saturated liquid-vapor mixture needs to be cooled to the saturation temperature at 1 MPa, which is 151.81°C. The specific enthalpy of the saturated liquid at 151.81°C is hf = 670.68 kJ/kg. The additional energy needed to be withdrawn from the mixture can be calculated as Q = m' × hf = 0.533 × 670.68 = 357.14 kJ.
Thus, the additional amount of energy needed to be withdrawn from the saturated liquid-vapor mixture to complete the condensation is 357.14 kJ.
Learn more about water vapor
https://brainly.com/question/14529481
#SPJ11
Consider the series resonant circuit shown in the figure with L=80μH, R=14.14Ω, and C=1000pF.
Compute the resonant frequency, bandwidth, lower half-power frequency, higher half-power frequency, Assuming that the frequency of the source is the same as the resonant frequency, find the phasor voltage VC, Assuming that the frequency of the source is the same as the resonant frequency, find the phasor voltage VL, Assuming that the frequency of the source is the same as the resonant frequency, find the phasor voltage VR.
The resonant frequency of the series resonant circuit is approximately 1.59 MHz. The bandwidth, lower half-power frequency, and higher half-power frequency can be calculated using the given values of L, R, and C.
To determine the resonant frequency, we can use the formula:
Resonant frequency (fr) = 1 / (2π√(LC))
Using the given values of L = 80 μH and C = 1000 pF (which is equivalent to 1 nF), we can calculate the resonant frequency as follows:
fr = 1 / (2π√(80μH × 1nF)) ≈ 1.59 MHz
To calculate the bandwidth, we can use the formula:
Bandwidth (BW) = R / L
Using R = 14.14 Ω and L = 80 μH, we can find the bandwidth as follows:
BW = 14.14 Ω / 80 μH ≈ 176.75 kHz
The lower half-power frequency is calculated as:
Lower half-power frequency = fr - (BW / 2)
Substituting the values, we have:
Lower half-power frequency = 1.59 MHz - (176.75 kHz / 2) ≈ 1.44 MHz
The higher half-power frequency is calculated as:
Higher half-power frequency = fr + (BW / 2)
Substituting the values, we have:
Higher half-power frequency = 1.59 MHz + (176.75 kHz / 2) ≈ 1.74 MHz
To find the phasor voltages, we need more information about the source. The phasor voltage VC can be found using the voltage divider formula, while the phasor voltages VL and VR depend on the source and the circuit configuration.
Learn more about resonant circuits
brainly.com/question/29045377
#SPJ11
use ANSYS software to design . set your own dimensions of the plate and loading use your own modal values designing the plate with one end section fixed as in the picture. get the stress and fatigue life using fatigue analysis using fatigue tool. please show the steps pictures and results of the simulation.
Please complete the fatigue analysis of a simple plate with one end section fixed. You can use the aluminium material. fixed Such a structure. Try to get the stress distribution and life. You need using the S-N data of the material.
The fatigue properties of a material are determined by series of test. For most steels there is a level of fatigue limit below which a component will survive an infinite number of cycles, for aluminum and titanium a fatigue limit can not be defined, as failure will eventually occur after enough experienced cycles.
Although there is a cyclic stress, there are also stresses complex circumstances involving tensile to compresive and constant stress, where the solution is given into the mean stress and the stress amplitude or stress range, which is double the stress amplitude.
Low‐cycle fatigue is defined as few thousand cycles and high cycle fatigue is around more than 10,000 cycles. The number of cycles for failure on brittle materials are less and determined compared with the ductile materials.
The bending fatigue could be handled with specific load requirements for uniform bending or axial fatigue of the same section size where the material near the surface is subjected to the maximum stress, as in torsional fatigue, which can be performed on axial-type specially designed machines also, using the proper fixtures if the maximum twist required is small, in which linear motion is changed to rotational motion.
Learn more about stress amplitude on:
https://brainly.com/question/32075824
#SPJ4
11. In addition to cooling towers, name one of two other common sources for cooling water for major electrical generation power plants. 12. Define what the range for a cooling tower means.
11. Apart from cooling towers, the Mississippi River, Lake Michigan, or other rivers/lakes are common sources of cooling water for significant electrical power generation plants.
12. The cooling tower range indicates the difference in temperature between the cold-water inlet and the hot water outlet for a cooling tower.The following are additional details about cooling tower and its range:What is a cooling tower?A cooling tower is a mechanism that cools the hot water that arises as a by-product of industrial or electrical power generation processes. Cooling towers are widely utilized in manufacturing and industrial activities such as oil refineries, petrochemical and chemical plants, thermal power stations, and HVAC systems.
The range for a cooling tower refers to the difference in temperature between the cold-water inlet and the hot water outlet for the cooling tower. The range is determined by calculating the difference in temperature between the hot water outlet and the cold water inlet.To get a specific range, follow these steps:1. Take the temperature of the cold water inlet.2. Take the temperature of the hot water outlet.3. Calculate the difference in temperature between the cold water inlet and the hot water outlet.The range is determined by taking the difference between the cold water inlet and the hot water outlet temperature. The range is a significant aspect of the cooling tower's overall operation because it has a direct impact on the cooling capacity.
To know more about cooling towers, visit:
https://brainly.com/question/13507664
#SPJ11
Use an iterative numerical technique to calculate a value
Assignment
The Mannings Equation is used to find the Flow Q (cubic feet per second or cfs) in an open channel. The equation is
Q = 1.49/n * A * R^2/3 * S^1/2
Where
Q = Flowrate in cfs
A = Cross Sectional Area of Flow (square feet)
R = Hydraulic Radius (Wetted Perimeter / A)
S = Downward Slope of the Channel (fraction)
The Wetted Perimeter and the Cross-Section of Flow are both dependent on the geometry of the channel. For this assignment we are going to use a Trapezoidal Channel.
If you work out the Flow Area you will find it is
A = b*y + y*(z*y) = by + z*y^2
The Wetted Perimeter is a little trickier but a little geometry will show it to be
W = b + 2y(1 + z^2)^1/2
where b = base width (ft); Z = Side slope; y = depth.
Putting it all together gives a Hydraulic Radius of
R = (b*y + Z*y^2)/(b + 2y*(1+Z^2))^1/2
All this goes into the Mannings Equations
Q = 1/49/n * (b*y + z*y^2) * ((b*y + Z*y^2)/(b + 2y(1+Z^2))^1/2)^2/3 * S^1/2
Luckily I will give you the code for this equation in Python. You are free to use this code. Please note that YOU will be solving for y (depth in this function) using iterative techniques.
def TrapezoidalQ(n,b,y,z,s):
# n is Manning's n - table at
# https://www.engineeringtoolbox.com/mannings-roughness-d_799.html
# b = Bottom width of channel (ft)
# y = Depth of channel (ft)
# z = Side slope of channel (horizontal)
# s = Directional slope of channel - direction of flow
A = b*y + z*y*y
W = b + 2*y*math.sqrt(1 + z*z)
R = A/W
Q = 1.49/n * A * math.pow(R, 2.0/3.0) * math.sqrt(s)
return Q
As an engineer you are designing a warning system that must trigger when the flow is 50 cfs, but your measuring systems measures depth. What will be the depth where you trigger the alarm?
The values to use
Manning's n - Clean earth channel freshly graded
b = 3 foot bottom
z = 2 Horiz : 1 Vert Side Slope
s = 1 foot drop for every 100 feet
n = 0.022
(hint: A depth of 1 foot will give you Q = 25.1 cfs)
Write the program code and create a document that demonstrates you can use the code to solve this problem using iterative techniques.
You should call your function CalculateDepth(Q, n, w, z, s). Inputs should be Q (flow), Manning's n, Bottom Width, Side Slope, Longitudinal Slope. It should demonstrate an iterative method to converge on a solution with 0.01 foot accuracy.
As always this will be done as an engineering report. Python does include libraries to automatically work on iterative solutions to equations - you will not use these for this assignment (but are welcome to use them in later assignments). You need to (1) figure out the algorithm for iterative solutions, (2) translate that into code, (3) use the code to solve this problem, (4) write a report of using this to solve the problem.
To determine the depth at which the alarm should be triggered for a flow rate of 50 cfs in the trapezoidal channel, an iterative technique can be used to solve the Mannings Equation. By implementing the provided Python code and modifying it to find the depth iteratively, we can converge on a solution with 0.01 foot accuracy.
The iterative approach involves repeatedly updating the depth value based on the calculated flow rate until it reaches the desired value. Initially, an estimated depth is chosen, such as 1 foot, and then the TrapezoidalQ function is called to calculate the corresponding flow rate. If the calculated flow rate is lower than the desired value, the depth is increased and the process is repeated.
Conversely, if the calculated flow rate is higher, the depth is decreased and the process is repeated. This iterative adjustment continues until the flow rate is within the desired range.
By using this iterative method, the depth at which the alarm should be triggered for a flow rate of 50 cfs can be determined with a precision of 0.01 foot. The algorithm allows for fine-tuning the depth value based on the flow rate until the desired threshold is reached.
Learn more about Trapezoidal
brainly.com/question/31380175
#SPJ11
An auditorium seating 1800 people in three consecutive sitting for 6 hours, is to be maintained at 25∘ C dry bulb and 20∘ C wet bulb temperatures with outdoor air at 35∘ C dry bulb and 60% relative humidity. Conditioned air enters the auditorium at 15∘ C. Ventilation requirement is 8 m 3/hr per person. Solar and other heat loads amount to 108,000KJ/hr. The sensible and latent heat loads from the occupants is 275KJ/hr per person and 150KJ/hr per person, respectively. The total latent heat load from the occupants is nearest to what value? 75,000KJ/hr 270,000KJ/hr 225,000KJ/hr 90,000KJ/hr
The total latent heat load from the occupants of the auditorium is approximately 225,000 KJ/hr.The correct answer is option C.
Given,Q = n × (Qs + Ql) + QpQ = 1800 × (275 + 150) + 108000= 962,000 KJ/hrQr = Q - Qp= 962,000 - 108,000= 854,000 KJ/hrQva = n × Qv= 1800 × 8= 14,400 m3/hrQsa = Q + Qva × (t2 - t1)= 962,000 + 14,400 × (25 - 15)= 1,100,800 KJ/hrQsra = Qsa × (t2 - t1) × 1.005= 1,100,800 × 10 × 1.005= 11,086,040 KJ/hrW2 = 0.0107 kg/kg of dry air, from the psychrometric chart for (t2 = 25 ∘C, t3 = 20 ∘C and RH4 = 60%).W1 = 0.0264 kg/kg of dry air, from the psychrometric chart for (t4 = 35 ∘C and RH4 = 60%).Qlra = Qsa × (W2 - W1) × 1.86= 1,100,800 × (0.0107 - 0.0264) × 1.86= - 29,243.28 KJ/hr (Negative sign indicates that moisture is added to the air)Qm = n × Ql= 1800 × 150= 270,000 KJ/hrWa = n × Ql ÷ 2445= 1800 × 150 ÷ 2445= 110.29 kg of water/hrWs = Qsa × W2 ÷ 2445= 1,100,800 × 0.0107 ÷ 2445= 4.81 kg of water/hrWm = Ws - Wa= 4.81 - 110.29= - 105.48 kg of water/hr (Negative sign indicates that the moisture is removed from the air)
Therefore, the total latent heat load from the occupants of the auditorium is approximately 225,000 KJ/hr (nearest to).Answer: 225,000KJ/hr.
For more such questions on occupants,click on
https://brainly.com/question/30047809
#SPJ8
You know that widely used plastic bottles of carbonated drinks are made from PET plastic. Considering that CO2 is permeable for PET plastic, what is the diffusion flux at 298 K? Note that permeability coefficient for carbon dioxide is 0.5⋅10−13[cm2 s⋅Pa], pressure inside and outside the bottle are 1 MPa and 0.1 kPa, respectively. Let’s consider that bottle is a hollow cylinder with diameter of 30 mm, height of 100 mm and thickness of 0.05 cm. What is expiration date of this bottle if it considers decarbonized when 500 cm3 of CO2 will diffuse? Assuming a condition of steady state diffusion, calculate diffusion flux at 350 K if activation energy is 50 kJ/mol. How fast will the bottle lose fizz in this case? Compare two cases.
The diffusion flux of carbon dioxide through the PET plastic bottle at 298 K is approximately 7.95 x 10^(-11) mol/(cm^2·s).
To calculate the diffusion flux of carbon dioxide through the PET plastic bottle at 298 K, we can use Fick's law of diffusion:
J = -D * (ΔC/Δx)
Where:
J is the diffusion flux (mol/(cm^2·s))
D is the diffusion coefficient (cm^2/s)
ΔC is the concentration difference (mol/cm^3)
Δx is the thickness of the bottle (cm)
The diffusion coefficient for carbon dioxide in PET plastic is given as 0.5 x 10^(-13) cm^2·s·Pa. However, the pressure units need to be converted to match the diffusion coefficient. Thus, 1 MPa is equal to 10^7 Pa and 0.1 kPa is equal to 100 Pa.
Using the given values, we can calculate the concentration difference (ΔC) as follows:
ΔC = (P_inside - P_outside) / (RT)
Where:
P_inside is the pressure inside the bottle (1 MPa)
P_outside is the pressure outside the bottle (0.1 kPa)
R is the ideal gas constant (8.314 J/(mol·K))
T is the temperature in Kelvin (298 K)
ΔC = ((1 MPa) - (0.1 kPa)) / ((8.314 J/(mol·K)) * (298 K))
= 9.9 x 10^6 Pa / 2472.972 J/mol
≈ 4.004 x 10^3 mol/cm^3
Now, we can calculate the diffusion flux (J) using the given formula:
J = -D * (ΔC/Δx)
= -(0.5 x 10^(-13) cm^2·s·Pa) * (4.004 x 10^3 mol/cm^3) / (0.05 cm)
≈ -7.95 x 10^(-11) mol/(cm^2·s)
The negative sign indicates that the diffusion flux is from inside the bottle to the outside.
The diffusion flux of carbon dioxide through the PET plastic bottle at 298 K is approximately 7.95 x 10^(-11) mol/(cm^2·s). This means that a certain amount of CO2 will continuously diffuse out of the bottle, leading to a gradual loss of fizz over time.
To determine the expiration date of the bottle when 500 cm^3 of CO2 will diffuse, we need additional information such as the initial volume of CO2 inside the bottle and the rate of diffusion.
To learn more about diffusion, visit
https://brainly.com/question/28815433
#SPJ11
What pressure (in MPa) is generated when 1 kmol of oxygen gas is stored in a volume of 0.11 m³ and at a temperature of 310 K? Base your calculations on: a) the ideal gas equation. P = b) The van der Waals equation of state (keep an eye on your units!):
P = RT/v-b - a/v² where a = 3Pcvc² and b = Vc/3
8.06 MPa pressure (in MPa) is generated when 1 kmol of oxygen gas is stored in a volume of 0.11 m³ and at a temperature of 310 K.
(a) Using the Ideal gas equation:
P = nRT/V
Where n = 1 kmol of oxygen gas
V = 0.11 m³T = 310 K andR = 8.31 J/Kmol-K, converting it to MPa.1 J = 1 MPa*1 L = 0.001 m³
P = nRT/V= (1000 mol)(8.31 J/mol-K)(310 K) / 0.11 m³= 730880.73 J/m³= 730.88073 MPa
(b) Using the Van der Waals equation of state:
P = (RT)/(V - b) - a / (V²)
Where
a = 3Pcv²c = (22.4 L/mol) / 1000 = 0.0224 m³/mol
T = 310 K and R = 8.31 J/Kmol-Kb = Vc/3 = 0.0224/3 = 0.00747 m³/mol
Pc = 50 MPa, cv = 5/2 R, and P = ?
a = 3Pc(cv)² = 3(50 MPa)[(5/2)(8.31 J/mol-K)]²= 315.812 J/m³
P = (RT)/(V - b) - a / (V²)
Substituting values and simplifying,
P = [(8.31 J/mol-K)(310 K)] / [0.11 m³ - 0.00747 m³/mol] - (315.812 J/m³) / [(0.11 m³)²]= 8.06 MPa.
To know more about Ideal gas equation visit:
https://brainly.com/question/15379358
#SPJ11