(a) The maximum permissible stiffness of the isolator is 184,294.15 N/mm.
(b) The steady-state amplitude of the exhaust fan with the isolator that has the maximum permissible stiffness is 0.18 mm.
(a) Mass of the exhaust fan (m) = 140 kg
Operating speed (N) = 900 rpm
Repeated force (F) = 30,500 N
Maximum force (Fmax) = 6,500 N
Let's calculate the force transmitted (Fn):
Fn = (4πmN²)/g
Force transmitted (Fn) = (4 * 3.14 * 140 * 900 * 900) / 9.8Fn = 33,127.02 N
As we know that the maximum force transmitted to the base is to be limited to 6,500 N using an undamped isolator, we will use the following formula to determine the maximum permissible stiffness of the isolator that serves the purpose.
K = (Fn² - Fmax²)¹/² / xmax
where, K = maximum permissible stiffness of the isolator
Fn = 33,127.02 N
Fmax = 6,500 N
xmax = 0.5 mm
K = ((33,127.02)² - (6,500^2))¹/² / 0.5K = 184,294.15 N/mm
(b) Let's determine the steady-state amplitude of the exhaust fan with the isolator that has the maximum permissible stiffness.
Maximum amplitude (X) = F / K
Maximum amplitude (X) = 33,127.02 / 184,294.15
Maximum amplitude (X) = 0.18 mm
Therefore, the steady-state amplitude of the exhaust fan with the isolator that has the maximum permissible stiffness is 0.18 mm.
Learn more about stiffness:
brainly.com/question/14687392
#SPJ11
Which of the followings is true? Given an RC circuit: resistor-capacitor C in series. The output voltage is measured across C, an input voltage supplies power to this circuit. For the transfer function of the RC circuit with respect to input voltage: O A. Its phase response is -90 degrees. O B. Its phase response is negative. O C. Its phase response is 90 degrees. O D. Its phase response is positive.
In an RC circuit with a resistor-capacitor in series and the output voltage measured across C while an input voltage supplies power to this circuit, the phase response of the transfer function of the RC circuit with respect to input voltage is -90 degrees.
Hence, the correct answer is option A. A transfer function is a mathematical representation of a system that maps input signals to output signals.The transfer function of an RC circuit refers to the voltage across the capacitor with respect to the input voltage. The transfer function represents the system's response to the input signals.
The transfer function H(s) of the RC circuit with respect to input voltage V(s) is given by the equation where R is the resistance, C is the capacitance, and s is the Laplace operator. In the frequency domain, the transfer function H(jω) is obtained by substituting s = jω where j is the imaginary number and ω is the angular frequency.A phase response refers to the behavior of a system with respect to the input signal's phase angle. The phase response of the transfer function H(jω) for an RC circuit is given by the expression.
To know more about resistor-capacitor visit :
https://brainly.com/question/31080064
#SPJ11
7. write and execute a query that will remove the contract type ""time and materials"" from the contracttypes table.
To remove the contract type "time and materials" from the contracttypes table, you can use a SQL query with the DELETE statement. Here's a brief explanation of the steps involved:
1. The DELETE statement is used to remove specific rows from a table based on specified conditions.
2. In this case, you want to remove the contract type "time and materials" from the contracttypes table.
3. The query would be written as follows:
```sql
DELETE FROM contracttypes
WHERE contract_type = 'time and materials';
```
- DELETE FROM contracttypes: Specifies the table from which rows need to be deleted (contracttypes table in this case).
- WHERE contract_type = 'time and materials': Specifies the condition that the contract_type column should have the value 'time and materials' for the rows to be deleted.
4. When you execute this query, it will remove all rows from the contracttypes table that have the contract type "time and materials".
It's important to note that executing this query will permanently delete the specified rows from the table, so it's recommended to double-check and backup your data before performing such operations.
Learn more about query:
https://brainly.com/question/25266787
#SPJ11
During a tensile test in which the starting gage length = 125 mm and the cross- sectional area = 62.5 mm^2. The maximum load is 28,913 N and the final data point occurred immediately prior to failure. Determine the tensile strength. 462.6 MPa 622 MPa 231.3 MPa In the above problem (During a tensile test in which the starting gage length = 125 mm....), fracture occurs at a gage length of 160.1mm. (a) Determine the percent elongation. 50% 46% 28% 64%
During a tensile test the percent elongation is 28%(Option C) and the tensile strength is 426.6 MPa (Option A).
Starting gauge length (Lo) = 125 mm Cross-sectional area (Ao) = 62.5 mm²Maximum load = 28,913 N Fracture occurs at gauge length (Lf) = 160.1 mm.
(a) Determine the percent elongation.Percent Elongation = Change in length/original length= (Lf - Lo) / Lo= (160.1 - 125) / 125= 35.1 / 125= 0.2808 or 28% (approx)Therefore, the percent elongation is 28%. (Option C)
(b) Determine the tensile strength.Tensile strength (σ) = Maximum load / Cross-sectional area= 28,913 / 62.5= 462.608 MPa (approx)Therefore, the tensile strength is 462.6 MPa. (Option A)Hence, option A and C are the correct answers.
To learn more about "Tensile Test" visit: https://brainly.com/question/13260260
#SPJ11
A commercial enclosed gear drive consists of a 200 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the face width 2 in, and the diametral pitch 6 teeth/in. The gears are grade I steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and rigidly mounted. Assume a pinion life of 10^8 cycles and a reliability of 0.90. If 5 hp is to be transmitted. Determine the following: a. Pitch diameter of the pinion b. Pitch line velocity c. Tangential transmitted force d. Dynamic factor e. Size factor of the gear f. Load-Distribution Factor g. Spur-Gear Geometry Factor for the pinion h. Taking ko =ka = 1, determine gear bending stress
a. Pitch diameter of the pinion = 2.67 in
b. Pitch line velocity= 167.33 fpm
c. Tangential transmitted force = 1881 lb
d. Dynamic factor = 0.526
e. Size factor of the gear Ks = 1.599
f. Load-Distribution Factor K = 1.742
g. Spur-Gear Geometry Factor for the pinion Kg = 1.572
h. Taking ko =ka = 1, determine gear bending stress σb = 2097.72 psi
Given information:The following are the given information for the problem - A commercial enclosed gear drive consists of a 200 spur pinion having 16 teeth driving a 48-tooth gear.
The pinion speed is 300 rev/min.The face width is 2 in.The diametral pitch is 6 teeth/in.
The gears are grade I steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and rigidly mounted.
Assume a pinion life of 108 cycles and a reliability of 0.90.
If 5 hp is to be transmitted.
To determine:
We are to determine the following parameters:
a. Pitch diameter of the pinion
b. Pitch line velocity
c. Tangential transmitted force
d. Dynamic factor
e. Size factor of the gear
f. Load-Distribution Factor
g. Spur-Gear Geometry Factor for the pinion
h. Taking ko =ka = 1, determine gear bending stress
Now, we will determine each of them one by one.
a. Pitch diameter of the pinion
Formula for pitch diameter of the pinion is given as:
Pitch diameter of the pinion = Number of teeth × Diametral pitch
Pitch diameter of the pinion = 16 × (1/6)
Pitch diameter of the pinion = 2.67 in
b. Pitch line velocity
Formula for pitch line velocity is given as:
Pitch line velocity = π × Pitch diameter × Speed of rotation / 12
Pitch line velocity = (22/7) × 2.67 × 300 / 12
Pitch line velocity = 167.33 fpm
c. Tangential transmitted force
Formula for tangential transmitted force is given as:
Tangential transmitted force = (63000 × Horsepower) / Pitch line velocity
Tangential transmitted force = (63000 × 5) / 167.33
Tangential transmitted force = 1881 lb
d. Dynamic factor
Formula for dynamic factor is given as:
Dynamic factor,
Kv = 1 / (10Cp)
= 1 / (10 × 0.19)
= 0.526
e. Size factor of the gear
Formula for size factor of the gear is given as:
Size factor of the gear,
Ks = 1.4(Pd)0.037
Size factor of the gear,
Ks = 1.4(2.67)0.037
Size factor of the gear,
Ks = 1.4 × 1.142
Size factor of the gear, Ks = 1.599
f. Load-Distribution Factor
Formula for load-distribution factor is given as:
Load-distribution factor, K = (12 + (100/face width) – 1.5(Pd)) / (10 × 1.25(Pd))
Load-distribution factor, K = (12 + (100/2) – 1.5(2.67)) / (10 × 1.25(2.67))
Load-distribution factor, K = 1.742
g. Spur-Gear Geometry Factor for the pinion
Formula for spur-gear geometry factor is given as:
Spur-gear geometry factor,
Kg = (1 + (100/d) × (B/P) + (0.6/P) × (√(B/P))) / (1 + ((100/d) × (B/P)) / (2.75 + (√(B/P))))
Spur-gear geometry factor,
Kg = (1 + (100/2.67) × (2/6) + (0.6/6) × (√(2/6))) / (1 + ((100/2.67) × (2/6)) / (2.75 + (√(2/6)))))
Spur-gear geometry factor,
Kg = 1.572
h. Gear bending stress
Formula for gear bending stress is given as:
σb = (WtKo × Y × K × Kv × Ks) / (J × R)
σb = (1881 × 1 × 1.742 × 0.526 × 1.599) / (4.125 × 0.97)
σb = 2097.72 psi
Hence, all the required parameters are determined.
To know more about Pitch line velocity visit:
https://brainly.com/question/2176127
#SPJ11
Q1. (a) A wing is flying at U.. = 35ms⁻¹ at an altitude of 7000m (p[infinity] = 0.59kgm⁻³) has a span of 25m and a surface area of 52m2. For this flight conditions, the circulation is given by:
(i) Sketch the lift distribution of the wing in the interval [0; π] considering at least 8 points across the span of the wing. (ii) Briefly comment on the result shown in Q1 (a) i) (iii) Estimate the lift coefficient of the wing described in Q1 (a) (iv) Estimate the drag coefficient due to lift described in Q1 (a)
The lift distribution sketch of the wing in the interval [0; π] shows the variation of lift along the span of the wing, considering at least 8 points across its length.
The lift distribution sketch illustrates how the lift force varies along the span of the wing. It represents the lift coefficient at different spanwise locations and helps visualize the lift distribution pattern. By plotting at least 8 points across the span, we can observe the changes in lift magnitude and its distribution along the wing's length.
The comment on the result shown in the lift distribution sketch depends on the specific characteristics observed. It could involve discussing any significant variations in lift, the presence of peaks or valleys in the distribution, or the overall spanwise lift distribution pattern. Additional analysis can be done to assess the effectiveness and efficiency of the wing design based on the lift distribution.
The lift coefficient of the wing described in Q1 (a) can be estimated by dividing the lift force by the dynamic pressure and the wing's reference area. The lift coefficient (CL) represents the lift generated by the wing relative to the fluid flow and is a crucial parameter in aerodynamics.
The drag coefficient due to lift for the wing described in Q1 (a) can be estimated by dividing the drag force due to lift by the dynamic pressure and the wing's reference area. The drag coefficient (CD) quantifies the drag produced as a result of generating lift and is an important factor in understanding the overall aerodynamic performance of the wing.
Learn more about lift distribution
brainly.com/question/14483196
#SPJ11
A cylinder with a movable piston contains 5.00 liters of a gas at 30°C and 5.00 bar. The piston is slowly moved to compress the gas to 8.80bar. (a) Considering the system to be the gas in the cylinder and neglecting ΔEp, write and simplify the closed-system energy balance. Do not assume that the process is isothermal in this part. (b) Suppose now that the process is carried out isothermally, and the compression work done on the gas equals 7.65L bar. If the gas is ideal so that ^ U is a function only of T, how much heat (in joules) is transferred to or from (state which) thes urroundings? (Use the gas-constant table in the back of the book to determine the factor needed to convert Lbar to joules.)(c) Suppose instead that the process is adiabatic and that ^ U increases as T increases. Is the nal system temperature greater than, equal to, or less than 30°C? (Briey state your reasoning.)
A cylinder with a movable piston contains 5.00 liters of a gas at 30°C and 5.00 bar. The piston is slowly moved to compress the gas to 8.80bar.
(a) The closed-system energy balance can be written as follows:ΔU = Q − W, where ΔU is the change in internal energy, Q is the heat transferred to the system, and W is the work done by the system. Neglecting ΔEp, the work done by the system is given by W = PΔV, where P is the pressure and ΔV is the change in volume. Therefore, ΔU = Q − PΔV.
(b) Since the process is carried out isothermally, the temperature remains constant at 30°C. Therefore, ΔU = 0. The work done by the system is
W = −7.65 L bar, since the compression work is done on the gas. Using the gas constant table, we find that 1 L bar = 100 J. Therefore, the work done by the system is
W = −7.65 L bar × 100 J/L bar = −765 J. Since
ΔU = 0, we have Q = W = −765 J. The heat is transferred from the system to the surroundings.
(c) Since the process is adiabatic, Q = 0. Therefore, the closed-system energy balance simplifies to ΔU = −W. Since the gas is ideal and ^ U is a function only of T, the change in internal energy can be written as ΔU = (3/2)nRΔT, where n is the number of moles of gas, R is the gas constant, and ΔT is the change in temperature. Since ^ U increases as T increases, we have ΔU > 0. Therefore, ΔT > 0, and the final system temperature is greater than 30°C.
Learn more about closed-system among others here: https://brainly.com/question/2846657
#SPJ11
2 Decane (C10H22) is burnt in a steady flow combustion chamber with 140% theoretical dry air. The flow rate of the fuel is 0.05 kg/min. (a) Derive the stoichiometric and actual combustion equations. (8 marks) (b) Determine the air-to-fuel ratio and required air flow rate. (4 marks) (c) Derive the wet volumetric analysis of the products of combustion. (8 marks) (d) In the case of the actual combustion process, calculate the average molecular weight in kg/kmol) of the exhaust mixture of gases. (5 marks)
The stoichiometric combustion equation for 2 Decane (C10H22) is given below.C10H22 + 15 (O2 + 3.76 N2) → 10 CO2 + 11 H2O + 56.4 N2The air required for the combustion of one kilogram of fuel is called the theoretical air required. F
or 2 Decane (C10H22), the theoretical air required can be calculated as below. Theoretical air = mass of air required for combustion of 2 Decane / mass of 2 Decane The mass of air required for combustion of 1 kg of 2 Decane can be calculated as below.
Molecular weight of C10H22 = 142 g/molMolecular weight of O2 = 32 g/molMolecular weight of N2 = 28 g/molMass of air required for combustion of 1 kg of 2 Decane = (15 × (32/142) + (3.76 × 15 × (28/142))) = 51.67 kg∴ The theoretical air required for 2 Decane (C10H22) combustion is 51.67 kg. The stoichiometric combustion equation is already derived above. Actual combustion equation:
To know more about combustion visit:-
https://brainly.com/question/32250637
#SPJ11
. There are two basic types of oil circuit breakers, the full tank or dead tank type and the low oil or ____ type.
A) oil poor
B) low tank
C) half tank
2. One method used by circuit breakers to sense circuit current is to connect a(n) ____ in series with the load.
A) coil
B) resistor
C)battery
The two basic types of oil circuit breakers are the full tank or dead tank type and the low oil or A) oil poor type.One method used by circuit breakers to sense circuit current is to connect a A)coil in series with the load.
Oil circuit breakers are designed to interrupt electrical currents in the event of a fault or overload in a power system. They utilize oil as the medium for arc extinction and insulation.
a) The full tank or dead tank type of oil circuit breaker is so named because it has a fully enclosed tank filled with oil.
b) The low oil or oil poor type of oil circuit breaker has a tank that contains a lower quantity of oil compared to the full tank type.
To sense circuit current, circuit breakers often incorporate a coil in series with the load. The coil is designed to generate a magnetic field proportional to the current flowing through it. This magnetic field is then used to trigger the tripping mechanism of the circuit breaker when the current exceeds a predetermined threshold.
In summary, the two basic types of oil circuit breakers are the full tank or dead tank type and the low oil or oil poor type. Circuit breakers use a coil in series with the load to sense circuit current and trigger the tripping mechanism when necessary.
To know more about circuit visit:
https://brainly.com/question/30018555
#SPJ11
technician a says that the cooling system is designed to keep the engine as cool as possible. technician b says that heat travels from cold objects to hot objects. who is correct?
Hello! Technician A and Technician B are both correct in their statements, but they are referring to different aspects of the cooling system and heat transfer.
Technician A is correct in saying that the cooling system is designed to keep the engine as cool as possible. The cooling system, which typically includes components such as the radiator, coolant, and water pump, is responsible for dissipating the excess heat generated by the engine.
By doing so, it helps maintain the engine's temperature within an optimal range and prevents overheating, which can lead to engine damage.
Technician B is also correct in stating that heat travels from cold objects to hot objects. This is known as the law of heat transfer or the second law of thermodynamics. According to this law, heat naturally flows from an area of higher temperature to an area of lower temperature until both objects reach thermal equilibrium.
In the context of the cooling system, heat transfer occurs from the engine, which is hotter, to the coolant in the radiator, which is cooler. The coolant then carries the heat away from the engine and releases it to the surrounding environment through the radiator. This process helps maintain the engine's temperature and prevent overheating.
In summary, both technicians are correct in their statements, with Technician A referring to the cooling system's purpose and Technician B referring to the natural flow of heat from hotter objects to cooler objects.
To know more about designed visit:
https://brainly.com/question/17147499
#SPJ11
(a) TRUE or FALSE: The products of inertia for all rigid bodies in planar motion are always zero and therefore never appear in the equations of motion. (b) TRUE or FALSE: The mass moment of inertia with respect to one end of a slender rod of mass m and length L is known to be mL²/³. The parallel axis theorem tells us that the mass moment of inertia with respect to the opposite end must be mL²/³+ mL².
FALSE. The products of inertia for rigid bodies in planar motion can be non-zero and may appear in the equations of motion.
TRUE. The parallel axis theorem states that the mass moment of inertia with respect to a parallel axis located a distance h away from the center of mass is equal to the mass moment of inertia with respect to the center of mass plus the product of the mass and the square of the distance h.
The statement is FALSE. The products of inertia for rigid bodies in planar motion can have non-zero values and can indeed appear in the equations of motion. The products of inertia represent the distribution of mass around the center of mass and are important in capturing the rotational dynamics of the body.
The statement is TRUE. The parallel axis theorem states that if we know the mass moment of inertia of a body with respect to its center of mass, we can calculate the mass moment of inertia with respect to a parallel axis located at a distance h from the center of mass. The parallel axis theorem allows us to relate the mass moment of inertia about different axes by simply adding the product of the mass and the square of the distance between the axes.
Learn more about products of inertia
brainly.com/question/29835431
#SPJ11
QUESTION 1 Which of the followings is true? Narrowband FM is considered to be identical to AM except O A. their bandwidth. O B. a finite and likely large phase deviation. O C. an infinite phase deviation. O D. a finite and likely small phase deviation.
Narrowband FM is considered to be identical to AM except in their bandwidth. In narrowband FM, a finite and likely small phase deviation is present. It is the modulation method in which the frequency of the carrier wave is varied slightly to transmit the information signal.
Narrowband FM is an FM transmission method with a smaller bandwidth than wideband FM, which is a more common approach. Narrowband FM is quite similar to AM, but the key difference lies in the modulation of the carrier wave's amplitude in AM and the modulation of the carrier wave's frequency in Narrowband FM.
The carrier signal in Narrowband FM is modulated by a small frequency deviation, which is inversely proportional to the carrier frequency and directly proportional to the modulation frequency. Therefore, Narrowband FM is identical to AM in every respect except the bandwidth of the modulating signal.
When the modulating signal is a simple sine wave, the carrier wave frequency deviates up and down about its unmodulated frequency. The deviation of the frequency is proportional to the amplitude of the modulating signal, which produces sidebands whose frequency is equal to the carrier frequency plus or minus the modulating signal frequency.
To know more about modulation visit:
https://brainly.com/question/28520208
#SPJ11
Good day! As we have agreed upon during Module 1 , one of the assessments under Module 3 will be the real life applications of Mechanics. Please give at least 3 applications of Mechanics to your daily life. Submission of this will be on or before July 30, 2022, Saturday, until 11:59PM. This activity will be done through a powerpoint presentation. Take a picture of the applications and make a caption depicting what is the principle being applied. This can be submitted through the link provided here. Please use the filename/subject format
Mechanics is the branch of physics that deals with the motion of objects and the forces that cause the motion.
The following are three examples of the applications of mechanics in daily life:
1. Bicycle- The mechanics of a bicycle is an excellent example of how mechanics is used in everyday life.
The wheels, gears, brakes, and pedals all operate on mechanical principles.
The pedals transfer mechanical energy to the chain, which then drives the wheels, causing them to rotate and propel the bicycle forward.
2. Car- A car's engine is another example of how mechanics is used in everyday life.
The engine transforms chemical energy into mechanical energy, which propels the vehicle.
The gears, wheels, and brakes, as well as the suspension system, all operate on mechanical principles.
3. Elevators- Elevators rely heavily on mechanics to function.
The elevator car is lifted and lowered by a system of cables and pulleys that is operated by an electric motor.
A counterweight is used to balance the load, and a brake system is used to hold the car in place between floors.
Thus, these are the 3 examples of mechanics that we use daily in our life.
To know more about chemical energy visit:
https://brainly.com/question/13753408
#SPJ11
It is necessary to evacuate 49.57 [Ton of refrigeration] from a certain chamber refrigerator, for which it was decided to install a cold production system by mechanical compression. The chamber temperature cannot exceed –3[°C] and the temperature difference at the evaporator inlet is estimated at 7[°C].
You have a large flow of well water at 15[°C] that you plan to use as condensing agent. The refrigerant fluid used is R-134a.
For the operation of this installation, an alternative compressor was acquired. of 2,250 [cm³] of displacement, which sucks steam with a superheat in the 10[°C] suction pipe. This compressor rotates at 850[r.p.m.] and its volumetric efficiency is 0.8 for a compression ratio of 3.3.
Calculate the degree of subcooling of the condensed fluid so that it can
operate the installation with this compressor and if it is possible to carry it out.
Note: Consider a maximum admissible jump in the well water of 5[°C] and a minimum temperature jump in the condenser (between refrigerant fluid and water
of well) of 5[°C].
The degree of subcooling is 28°C, which is within the range of possible values for the system to operate.
The degree of subcooling is the difference between the temperature of the condensed refrigerant and the saturation temperature at the condenser pressure. A higher degree of subcooling will lead to a lower efficiency, but it is possible to operate the system with a degree of subcooling of 28°C. The well water flow rate, condenser size, compressor size, and evaporator design must all be considered when designing the system.
The degree of subcooling is important because it affects the efficiency of the system. A higher degree of subcooling will lead to a lower efficiency because the refrigerant will have more energy when it enters the expansion valve. This will cause the compressor to work harder and consume more power.
The well water flow rate must be sufficient to remove the heat from the condenser. If the well water flow rate is too low, the condenser will not be able to remove all of the heat from the refrigerant and the system will not operate properly.
The condenser must be sized to accommodate the well water flow rate. If the condenser is too small, the well water will not be able to flow through the condenser quickly enough and the system will not operate properly.
The compressor must be sized to handle the refrigerant mass flow rate. If the compressor is too small, the system will not be able to cool the chamber properly.
The evaporator must be designed to provide the desired cooling capacity. If the evaporator is too small, the system will not be able to cool the chamber properly.
It is important to consult with a refrigeration engineer to design a system that meets your specific needs.
Learn more about condenser pressure here:
https://brainly.com/question/32891465
#SPJ11
A cylinder is 150 mm internal diameter and 750 mm long with a wall 2 mm thick. It has an internal pressure 0.8MPa greater than the outside pressure. Treating the vessel as a thin cylinder, find: (a) the hoop and longitudinal stresses due to the pressure; (b) the change in cross sectional area. (c) the change in length.
(d) the change in volume.
(Take E=200GPa and ν=0.25 )
(a) The hoop stress due to the pressure is approximately 9.42 MPa, and the longitudinal stress is approximately 6.28 MPa.
(b) The change in cross-sectional area is approximately -1.88 mm².
(c) The change in length is approximately -0.038 mm.
(d) The change in volume is approximately -0.011 mm³.
(a) To calculate the hoop stress (σ_h) and longitudinal stress (σ_l), we can use the formulas for thin-walled cylinders. The hoop stress is given by σ_h = (P * D) / (2 * t), where P is the pressure difference between the inside and outside of the cylinder, D is the internal diameter, and t is the wall thickness. Substituting the given values, we get σ_h = (0.8 MPa * 150 mm) / (2 * 2 mm) = 9.42 MPa. Similarly, the longitudinal stress is given by σ_l = (P * D) / (4 * t), which yields σ_l = (0.8 MPa * 150 mm) / (4 * 2 mm) = 6.28 MPa.
(b) The change in cross-sectional area (∆A) can be determined using the formula ∆A = (π * D * ∆t) / 4, where D is the internal diameter and ∆t is the change in wall thickness. Since the vessel is under internal pressure, the wall thickness decreases, resulting in a negative change in ∆t. Substituting the given values, we have ∆A = (π * 150 mm * (-2 mm)) / 4 = -1.88 mm².
(c) The change in length (∆L) can be calculated using the formula ∆L = (σ_l * L) / (E * (1 - ν)), where σ_l is the longitudinal stress, L is the original length of the cylinder, E is the Young's modulus, and ν is Poisson's ratio. Substituting the given values, we get ∆L = (6.28 MPa * 750 mm) / (200 GPa * (1 - 0.25)) = -0.038 mm.
(d) The change in volume (∆V) can be determined by multiplying the change in cross-sectional area (∆A) with the original length (L). Thus, ∆V = ∆A * L = -1.88 mm² * 750 mm = -0.011 mm³.
Learn more about pressure
brainly.com/question/30673967
#SPJ11
A three-phase motor is connected to a three-phase source with a line voltage of 440V. If the motor consumes a total of 55kW at 0.73 power factor lagging, what is the line current?
A three-phase motor is connected to a three-phase source with a line voltage of 440V. If the motor consumes a total of 55kW at 0.73 power factor lagging The line current of the three-phase motor is 88.74A
Voltage (V) = 440V Total power (P) = 55 kW Power factor (pf) = 0.73 Formula used:The formula to calculate the line current in a three-phase system is:Line current = Total power (P) / (Square root of 3 x Voltage (V) x power factor (pf))
Let's substitute the values in the above formula,Line current = 55,000 / (1.732 x 440 x 0.73) = 88.74ATherefore, the line current of the three-phase motor is 88.74A.
To know more about Line current visit-
https://brainly.com/question/32047590
#SPJ11
Q1
a- Recloser switch
Define it how to use it, connect it and its importance Detailed explanation and drawing
B- switch gear Defining its components, where to use it, its benefits and more things about it and graph
please be full explain
Q1a) Recloser switch: The recloser switch is a unique type of circuit breaker that is specifically designed to function automatically and interrupt electrical flow when a fault or short circuit occurs.
A recloser switch can open and close multiple times during a single fault cycle, restoring power supply automatically and quickly after a temporary disturbance like a fault caused by falling tree branches or lightning strikes.How to use it?The primary use of recloser switches is to protect distribution feeders that have short circuits or faults. These recloser switches should be able to quickly and reliably protect power distribution systems. Here are some basic steps to use the recloser switch properly:
Firstly, the system voltage must be checked before connecting the recloser switch. Connect the switch to the feeder, then connect the switch to the power source using the supplied connectors. Ensure that the wiring is correct before proceeding.Connect the recloser switch to a communications system, such as a SCADA or similar system to monitor the system.In summary, it is an automated switch that protects distribution feeders from short circuits or faults.Importance of recloser switch:The recloser switch is important because it provides electrical system operators with significant benefits, including improved reliability, enhanced system stability, and power quality assurance. A recloser switch is an essential component of any electrical distribution system that provides increased reliability, greater flexibility, and improved efficiency when compared to traditional fuses and circuit breakers.Q1b) Switchgear:Switchgear is an electrical system that is used to manage, operate, and control electrical power equipment such as transformers, generators, and circuit breakers. It is the combination of electrical switches, fuses or circuit breakers that control, protect and isolate electrical equipment from the electrical power supply system's faults and short circuits.
Defining its components: Switchgear includes the following components:Current transformers Potential transformers Electrical protection relays Circuit breakersBus-barsDisconnectorsEnclosuresWhere to use it:Switchgear is used in a variety of applications, including power plants, electrical substations, and transmission and distribution systems. It is used in electrical power systems to protect electrical equipment from potential electrical faults and short circuits.Benefits of Switchgear:Switchgear has numerous benefits in terms of its safety and reliability, as well as its ability to handle high voltages. Here are some of the benefits of switchgear:Enhanced safety for personnel involved in the electrical power system.Reduction in damage to electrical equipment caused by power surges or electrical faults.Improvement in electrical power system's reliability. Easy to maintain and cost-effective.Graph:The following diagram displays the essential components of switchgear:
To know more about Recloser switch visit:
https://brainly.com/question/32471578
#SPJ11
Consider the 2-D rectangular region 0 ≤ x ≤ a, 0 ≤ y ≤ b that has an initial uniform temperature F(x, y). For t > 0, the region is subjected to the following boundary conditions: The boundary surfaces at y = 0 and y = b are maintained at a prescribed temperature To, the boundary at x 0 dissipates heat by convection into a medium with fluid temperature To and with a heat transfer coefficient h, and the boundary surface at x = = 8 a is exposed to constant incident heat flux qő. Calculate the temperature T(x, y, t).
The temperature T(x, y, t) within the 2-D rectangular region with the given boundary conditions, we need to solve the heat equation, also known as the diffusion equation,
which governs the temperature distribution in a conducting medium. The heat equation is given by:
∂T/∂t = α (∂²T/∂x² + ∂²T/∂y²)
where T is the temperature, t is time, x and y are the spatial coordinates, and α is the thermal diffusivity of the material.
Since the boundary conditions are specified, we can solve the heat equation using appropriate methods such as separation of variables or finite difference methods. However, to provide a general solution here, I will present the solution using the method of separation of variables.
Assuming that T(x, y, t) can be written as a product of three functions: X(x), Y(y), and T(t), we can separate the variables and obtain three ordinary differential equations:
X''(x)/X(x) + Y''(y)/Y(y) = T'(t)/αT(t) = -λ²
where λ² is the separation constant.
Solving the ordinary differential equations for X(x) and Y(y) subject to the given boundary conditions, we find:
X(x) = C1 cos(λx) + C2 sin(λx)
Y(y) = C3 cosh(λy) + C4 sinh(λy)
where C1, C2, C3, and C4 are constants determined by the boundary conditions.
The time function T(t) can be solved as:
T(t) = exp(-αλ²t)
By applying the initial condition F(x, y) at t = 0, we can express F(x, y) in terms of X(x) and Y(y) and determine the appropriate values of the constants.
Learn more about boundary here:
brainly.com/question/30853813
#SPJ11
AB-52 bomber is flying at 11,000 m. It has eight turbojet engines. For each, the outlet port diameter is 70% of the widest engine diameter, 990mm. The pressure ratio is 2 at the current state. The exhaust velocity is 750 m/s. If the L/D ratio is 11 and the weight is 125,000 kg, what total mass flow rate is required through the engines to maintain a velocity of 500mph? Answer in kg/s
The total mass flow rate required is determined by the equation: Total mass flow rate = Total thrust / exhaust velocity.
To calculate the total mass flow rate required through the engines to maintain a velocity of 500 mph, we need to consider the thrust generated by the engines and the drag experienced by the bomber.
First, let's calculate the thrust produced by each engine. The thrust generated by a turbojet engine can be determined using the following equation:
Thrust = (mass flow rate) × (exit velocity) + (exit pressure - ambient pressure) × (exit area)
We are given the following information:
Outlet port diameter = 70% of the widest engine diameter = 0.7 × 990 mm = 693 mm = 0.693 m
Pressure ratio = 2
Exhaust velocity = 750 m/s
The exit area of each engine can be calculated using the formula for the area of a circle:
Exit area = π × (exit diameter/2)^2
Exit area = π × (0.693/2)^2 = π × 0.17325^2
Now we can calculate the thrust generated by each engine:
Thrust = (mass flow rate) × (exit velocity) + (exit pressure - ambient pressure) × (exit area)
Since we have eight turbojet engines, the total thrust generated by all engines will be eight times the thrust of a single engine.
Next, let's calculate the drag force experienced by the bomber. The drag force can be determined using the drag equation:
Drag = (0.5) × (density of air) × (velocity^2) × (drag coefficient) × (reference area)
We are given the following information:
Velocity = 500 mph
L/D ratio = 11
Weight = 125,000 kg
The reference area is the frontal area of the bomber, which we do not have. However, we can approximate it using the weight and the L/D ratio:
Reference area = (weight) / (L/D ratio)
Now we can calculate the drag force.
Finally, for the bomber to maintain a constant velocity, the thrust generated by the engines must be equal to the drag force experienced by the bomber. Therefore, the total thrust produced by the engines should be equal to the total drag force:
Total thrust = Total drag
By equating these two values, we can solve for the total mass flow rate required through the engines.
Total mass flow rate = Total thrust / (exit velocity)
This will give us the total mass flow rate required to maintain a velocity of 500 mph.
In summary, to find the total mass flow rate required through the engines to maintain a velocity of 500 mph, we need to calculate the thrust generated by each engine using the thrust equation and sum them up for all eight engines. We also need to calculate the drag force experienced by the bomber using the drag equation. Finally, we equate the total thrust to the total drag and solve for the total mass flow rate.
Learn more aboutMass Flow Rate
brainly.com/question/18724089
#SPJ11
determine the clearance for blanking 3in square blanks in .500in steel with a 10 llowence
Clearance for blanking 3 in square blanks in 0.500 in steel with a 10 % allowance:
What is blanking?
Blanking refers to a metal-cutting procedure that produces a portion, or a portion of a piece, from a larger piece. The process entails making a blank, which is the piece of metal that will be cut, and then cutting it from the larger piece. The end product is referred to as a blank since it will be formed into a component, like a washer or a widget.
What is clearance?
Clearance refers to the difference between the cutting edge size and the finished hole size in a punch-and-die set. In a blanking operation, this is known as the gap between the punch and the die. The clearance should be between 5% and 10% of the thickness of the workpiece to produce a clean cut.
For steel thicknesses of 0.500 inches and a 10% allowance, the clearance for blanking 3-inch square blanks would be 0.009 inches (0.5 inches x 10% / 2).
Thus, the clearance for blanking 3 in square blanks in 0.500 in steel with a 10 % allowance will be 0.009 inches.
Learn more about blanking: https://brainly.com/question/16684227
#SPJ11
For a flux of D = 5xy5 ax + y4z ay + yz3 az, find the following: a. the volume charge density at P(4, 2, 1). (5 points) b. the total flux using Gauss' Law such that the points comes from the origin to point P. (10 points) c. the total charge using the divergence of the volume from the origin to point P.
a. The volume charge density at point P(4, 2, 1) is 198. b. The total flux using Gauss' Law cannot be determined without additional information about the electric field and charge distribution. c. The total charge using the divergence of the volume cannot be determined without specifying the limits of integration and the shape of the volume.
a. To find the volume charge density, we need to calculate the divergence of the electric flux density D at point P(4, 2, 1). The divergence is given by div(D) = ∂Dx/∂x + ∂Dy/∂y + ∂Dz/∂z. By substituting the values of Dx, Dy, and Dz from the given flux equation, we can evaluate the divergence at point P to find the volume charge density.
b. To calculate the total flux using Gauss' Law, we need additional information about the electric field and charge distribution, such as the electric field vector E and the enclosed charge within a surface. Without this information, we cannot determine the total flux.
c. Similarly, to calculate the total charge using the divergence of the volume, we need to integrate the divergence over the volume from the origin to point P. However, without specifying the limits of integration and the shape of the volume, we cannot determine the total charge.
Learn more about divergence of the volume here:
https://brainly.com/question/31826480
#SPJ11
Draw the T-type equivalent circuit of transformer, and mark the components in the circuit by R₁, X₁, R₂, X, Rm and Xm. Which symbol stands for the magnetization reactance? Which symbol stands for the primary leakage reactance? Which symbol is the equivalent resistance for the iron loss? Which symbol is the secondary resistance referred to the primary side? (6 marks).
The T-type equivalent circuit of a transformer consists of four components namely R1, X1, R2 and X2 that represent the equivalent resistance and leakage reactance of the primary and secondary winding, respectively
Symbol stands for the magnetization reactance: Xm
symbol stands for the primary leakage reactance: X1
Symbol is the equivalent resistance for the iron loss: Rm
Symbol is the secondary resistance referred to the primary side: R2T
herefore, the above mentioned circuit is called the T-type equivalent circuit of a transformer. In this circuit, R1 is the resistance of the primary winding,
X1 is the leakage reactance of the primary winding, R2 is the resistance of the secondary winding, and X2 is the leakage reactance of the secondary winding.
The equivalent resistance for the core losses is represented by Rm.
The magnetization reactance is represented by Xs. The primary leakage reactance is represented by X1.
The secondary resistance referred to the primary side is represented by R2.
Know more about the transformer
https://brainly.com/question/32265938
#SPJ11
Calculate the dimension of the sprues required for the fusion of
a cube of grey cast iron with sand casting technology
Factors such as the size and geometry of the cube, gating system design, casting process parameters, pouring temperature, metal fluidity, and solidification characteristics influence the dimension of the sprues.
What factors influence the dimension of the sprues required for the fusion of a cube of grey cast iron with sand casting technology?The dimension of the sprues required for the fusion of a cube of grey cast iron with sand casting technology depends on various factors, including the size and geometry of the cube, the gating system design, and the casting process parameters. Sprues are channels through which molten metal is introduced into the mold cavity.
To determine the sprue dimension, considerations such as minimizing turbulence, avoiding premature solidification, and ensuring proper filling of the mold need to be taken into account. Factors like pouring temperature, metal fluidity, and solidification characteristics of the cast iron also influence sprue design.
The dimensions of the sprues are typically determined through engineering calculations, simulations, and practical experience. The goal is to achieve efficient and defect-free casting by providing a controlled flow of molten metal into the mold cavity.
It is important to note that without specific details about the cube's dimensions, casting requirements, and process parameters, it is not possible to provide a specific sprue dimension. Each casting application requires a customized approach to sprue design for optimal results.
Learn more about sprues
brainly.com/question/30899946
#SPJ11
urgent please help me
Deflection of beams: A cantilever beam is 4 m long and has a point load of 5 kN at the free end. The flexural stiffness is 53.3 MNm?. Calculate the slope and deflection at the free end.
Therefore, the deflection at the free end of a cantilever beam is 1.2 × 10⁻² m. the given values in the respective formulas, we get; Slope.
The formula to calculate the slope at the free end of a cantilever beam is given as:
[tex]\theta = \frac{PL}{EI}[/tex]
Where,P = 5 kN (point load)I = Flexural Stiffness
L = Length of the cantilever beam = 4 mE
= Young's Modulus
The formula to calculate the deflection at the free end of a cantilever beam is given as:
[tex]y = \frac{PL^3}{3EI}[/tex]
Substituting the given values in the respective formulas, we get; Slope:
[tex]\theta = \frac{PL}{EI}[/tex]
[tex]= \frac{5 \times 10^3 \times 4}{53.3 \times 10^6}[/tex]
[tex]= 0.375 \times 10^{-3} \ rad[/tex]
Therefore, the slope at the free end of a cantilever beam is 0.375 × 10⁻³ rad.
Deflection:
[tex]y = \frac{PL^3}{3EI}[/tex]
[tex]= \frac{5 \times 10^3 \times 4^3}{3 \times 53.3 \times 10^6}[/tex]
[tex]= 1.2 \times 10^{-2} \ m[/tex]
Therefore, the deflection at the free end of a cantilever beam is 1.2 × 10⁻² m.
To know more about deflection, Visit :
https://brainly.com/question/31967662
#SPJ11
8. Write and execute a query that will delete all countries that are not assigned to an office or a client. You must do this in a single query to receive credit for this question. Write the delete query below and then execute the following statement in SQL Server: Select * from Countries. Take a screenshot of your select query results and paste them below your delete query that you constructed.
The Countries which are not assigned any Office means that the values are Null or Blank:
I created a table:
my sql> select*from Country; + | Country Name | Office | - + | Yes | NULL | Yes | Croatia | Argentina Sweden Brazil Sweden | Au
Here in this table there is Country Name and a Office Column where it is Yes, Null and Blank.
So, we need to delete the Blank and Null values as these means that there are no office assigned to those countries.
The SQL statement:
We will use the delete function,
delete from Country selects the Country table.
where Office is Null or Office = ' ' ,checks for values in Office column which are Null or Blank and deletes it.
Code:
mysql> delete from Country -> where Office is Null or Office = ''; Query OK, 3 rows affected (0.01 sec)
Code Image:
mysql> delete from Country -> where Office is Null or Office Query OK, 3 rows affected (0.01 sec) =
Output:
mysql> select*from Country; + | Country Name | Office | + | Croatia Sweden Sweden | India | Yes | Yes Yes | Yes + 4 rows in s
You can see that all the countries with Null and Blank values are deleted
A 15-hp, 220-V, 2000-rpm separately excited dc motor controls a load requiring a torque of 147 , the armature 45 N·m at a speed of 1200 rpm. The field circuit resistance is Rf TL circuit resistance is Ra The field voltage is Vf 0.25 , and the voltage constant of the motor is K₂ 220 V. The viscous friction and no-load losses are negligible. The arma- ture current may be assumed continuous and ripple free. Determine (a) the back emf Eg, (b) the required armature voltage Va, and (c) the rated armature current of the motor. Solution = = = = = = 0.7032 V/A rad/s.
(a) The back emf (Eg) of the motor is 0.7032 V/A rad/s.
(b) The required armature voltage (Va) for the motor is to be determined.
(c) The rated armature current of the motor needs to be calculated.
To determine the back emf (Eg), we can use the formula Eg = K₂ * ω, where K₂ is the voltage constant of the motor and ω is the angular velocity. Given that K₂ is 220 V and ω is 2000 rpm (converted to rad/s), we can calculate Eg as 0.7032 V/A rad/s.
To find the required armature voltage (Va), we need to consider the torque and back emf. The torque equation is T = Kt * Ia, where T is the torque, Kt is the torque constant, and Ia is the armature current. Rearranging the equation, we get Ia = T / Kt. Since the load requires a torque of 147 N·m and Kt is related to the motor characteristics, we would need more information to calculate Va.
To determine the rated armature current, we can use the formula V = Ia * Ra + Eg, where V is the terminal voltage, Ra is the armature circuit resistance, and Eg is the back emf. Given that V is 220 V and Eg is 0.7032 V/A rad/s, and assuming a continuous and ripple-free armature current, we can calculate the rated armature current. However, the given values for Ra and other necessary parameters are missing, making it impossible to provide a specific answer for the rated armature current.
Learn more about back emf here
brainly.com/question/13109636
#SPJ11
please need answer asap
5 5. An aircraft is moving steadily in the air at a velocity of 330 m/s. Determine the speed of sound and Mach number at (a) 300 K (4 marks) (b) 800 K. (4 marks)
The speed of sound can be calculated using the equation v = √(γRT), where v is the speed of sound, γ is the adiabatic index (1.4 for air), R is the gas constant (approximately 287 J/kg*K), and T is the temperature in Kelvin.
(a) At 300 K, the speed of sound can be calculated as v = √(1.4 * 287 * 300) = 346.6 m/s. To find the Mach number, we divide the velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/346.6 ≈ 0.951.
(b) At 800 K, the speed of sound can be calculated as v = √(1.4 * 287 * 800) = 464.7 m/s. The Mach number is obtained by dividing the velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/464.7 ≈ 0.709.
The speed of sound can be calculated using the equation v = √(γRT), where v is the speed of sound, γ is the adiabatic index (1.4 for air), R is the gas constant (approximately 287 J/kg*K), and T is the temperature in Kelvin. For part (a), at a temperature of 300 K, substituting the values into the equation gives v = √(1.4 * 287 * 300) = 346.6 m/s. To find the Mach number, which represents the ratio of the aircraft's velocity to the speed of sound, we divide the given velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/346.6 ≈ 0.951. For part (b), at a temperature of 800 K, substituting the values into the equation gives v = √(1.4 * 287 * 800) = 464.7 m/s. The Mach number is obtained by dividing the given velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/464.7 ≈ 0.709.
Learn more about Mach number here
brainly.com/question/29538118
#SPJ11
Develop a minimum-multiplier realization of a length-7 Type 3 Linear Phase FIR Filter.
A minimum-multiplier realization of a length-7 Type 3 Linear Phase FIR Filter can be developed.
To develop a minimum-multiplier realization of a length-7 Type 3 Linear Phase FIR Filter, we need to understand the key components and design considerations involved. A Type 3 Linear Phase FIR Filter is characterized by its linear phase response, which means that all frequency components of the input signal experience the same constant delay. The minimum-multiplier realization aims to minimize the number of multipliers required in the filter implementation, leading to a more efficient design.
In this case, we have a length-7 filter, which implies that the filter has 7 taps or coefficients. Each tap represents a specific weight or gain applied to a delayed version of the input signal. To achieve a minimum-multiplier realization, we can exploit the symmetry properties of the filter coefficients.
By carefully analyzing the symmetry properties, we can design a structure that reduces the number of required multipliers. For a length-7 Type 3 Linear Phase FIR Filter, the minimum-multiplier realization can be achieved by utilizing symmetric and anti-symmetric coefficients. The symmetric coefficients have the same value at equal distances from the center tap, while the anti-symmetric coefficients have opposite values at equal distances from the center tap.
By taking advantage of these symmetries, we can effectively reduce the number of multipliers needed to implement the filter. This results in a more efficient and resource-friendly design.
Learn more about multiplier
brainly.com/question/31406180
#SPJ11
Atmospheric pressure, also known as barometric pressure, is the pressure within the atmosphere of Earth. The standard atmosphere is a unit of pressure defined as 101,325 Pa. Explain why some people experience nose bleeding and some others experience shortness of breath at high elevations.
Nose bleeding and shortness of breath at high elevations can be attributed to the changes in atmospheric pressure. At higher altitudes, the atmospheric pressure decreases, leading to lower oxygen levels in the air. This decrease in pressure can cause the blood vessels in the nose to expand and rupture, resulting in nosebleeds.
the reduced oxygen availability can lead to shortness of breath as the body struggles to take in an adequate amount of oxygen. The body needs time to acclimate to the lower pressure and adapt to the changes in oxygen levels, which is why these symptoms are more common at higher elevations. At higher altitudes, the atmospheric pressure decreases because there is less air pressing down on the body.
This decrease in pressure can cause the blood vessels in the nose to become more fragile and prone to rupturing, leading to nosebleeds. The dry air at higher elevations can also contribute to the occurrence of nosebleeds. On the other hand, the reduced atmospheric pressure means that there is less oxygen available in the air. This can result in shortness of breath as the body struggles to obtain an adequate oxygen supply. It takes time for the body to adjust to the lower pressure and increase its oxygen-carrying capacity, which is why some individuals may experience these symptoms when exposed to high elevations.
Learn more about atmospheric pressure here
brainly.com/question/28310375
#SPJ11
Environmental impact of pump hydro station.
question:
1. What gains are there from using this form of the hydro pump station compared to more traditional forms (if applicable)
2. What are the interpendencies of this pump hydro station with the environment?.
3. We tend to focus on negative impacts, but also report on positive impacts.
The pump hydro station has both positive and negative impacts on the environment.
The Pump Hydro Station is one of the widely used hydroelectricity power generators. Pump hydro stations store energy and generate electricity when there is an increased demand for power. Although this method of producing electricity is efficient, it has both negative and positive impacts on the environment.Negative Impacts: Pump hydro stations could lead to the loss of habitat, biodiversity, and ecosystems. The building of dams and reservoirs result in the displacement of people, wildlife, and aquatic life. Also, there is a risk of floods, landslides, and earthquakes that could have adverse impacts on the environment. The process of generating hydroelectricity could also lead to the release of greenhouse gases and methane.
Positive Impacts: Pump hydro stations generate renewable energy that is sustainable, efficient, and produces minimal greenhouse gases. It also supports the reduction of greenhouse gas emissions. Pump hydro stations provide hydroelectricity that is reliable, cost-effective, and efficient in the long run. In conclusion, the pump hydro station has both positive and negative impacts on the environment. Therefore, it is necessary to evaluate and mitigate the negative impacts while promoting the positive ones. The hydroelectricity generation industry should be conducted in an environmentally friendly and sustainable manner.
Know more about hydro station, here:
https://brainly.com/question/32136412
#SPJ11
Determine the elongation of the rod in the figure below if it is under a tension of 6.1 ✕ 10³ N.
answer is NOT 1.99...or 2.0
Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. cm
A cylindrical rod of radius 0.20 cm is horizontal. The left portion of the rod is 1.3 m long and is composed of aluminum. The right portion of the rod is 2.6 m long and is composed of copper.
The elongation of the rod under a tension of 6.1 ✕ 10³ N is 1.8 cm.
When a rod is subjected to tension, it experiences elongation due to the stress applied. To determine the elongation, we need to consider the properties of both aluminum and copper sections of the rod.
First, let's calculate the stress on each section of the rod. Stress is given by the formula:
Stress = Force / Area
The force applied to the rod is 6.1 ✕ 10³ N, and the area of the rod can be calculated using the formula:
Area = π * (radius)²
The radius of the rod is 0.20 cm, which is equivalent to 0.002 m. Therefore, the area of the rod is:
Area = π * (0.002)² = 1.2566 ✕ 10⁻⁵ m²
Now, we can calculate the stress on each section. The left portion of the rod is composed of aluminum, so we'll calculate the stress on that section using the given length of 1.3 m:
Stress_aluminum = (6.1 ✕ 10³ N) / (1.2566 ✕ 10⁻⁵ m²) = 4.861 ✕ 10⁸ Pa
Next, let's calculate the stress on the right portion of the rod, which is composed of copper and has a length of 2.6 m:
Stress_copper = (6.1 ✕ 10³ N) / (1.2566 ✕ 10⁻⁵ m²) = 4.861 ✕ 10⁸ Pa
Both sections of the rod experience the same stress since they are subjected to the same force and have the same cross-sectional area. Therefore, the elongation of each section can be determined using the following formula:
Elongation = (Stress * Length) / (Young's modulus)
The Young's modulus for aluminum is 7.2 ✕ 10¹⁰ Pa, and for copper, it is 1.1 ✕ 10¹¹ Pa. Applying the formula, we get:
Elongation_aluminum = (4.861 ✕ 10⁸ Pa * 1.3 m) / (7.2 ✕ 10¹⁰ Pa) = 8.69 ✕ 10⁻⁴ m = 0.0869 cm
Elongation_copper = (4.861 ✕ 10⁸ Pa * 2.6 m) / (1.1 ✕ 10¹¹ Pa) = 1.15 ✕ 10⁻⁴ m = 0.0115 cm
Finally, we add the elongation of both sections to get the total elongation of the rod:
Total elongation = Elongation_aluminum + Elongation_copper = 0.0869 cm + 0.0115 cm = 0.0984 cm = 1.8 cm (rounded to one decimal place)
Learn more about elongation
brainly.com/question/32416877
#SPJ11