The minimum percent uncertainty of the proton's momentum is 49.7%.
Momentum of an electron = 68.1 ± 0.83
Location of an electron = 7.84 mm = 7.84 × 10⁶ nm
We know that, ∆x ∆p ≥ h/(4π)
Where,
∆x = uncertainty in position
∆p = uncertainty in momentum
h = Planck's constant = 6.626 × 10⁻³⁴ Js
Putting the given values,
∆x (68.1 ± 0.83) × 10⁻²⁷ ≥ (6.626 × 10⁻³⁴) / (4π)
∆x ≥ h/(4π × ∆p) = 6.626 × 10⁻³⁴ /(4π × (68.1 + 0.83) × 10⁻²⁷)
∆x ≥ 2.60 nm (approx)
Hence, the minimum uncertainty of the electron's position is 2.60 nm.
A proton has been accelerated by a potential difference of 23 kV. If its position is known to have an uncertainty of 4.63 fm, then the minimum percent uncertainty of the proton's momentum is given by:
∆x = 4.63 fm = 4.63 × 10⁻¹⁵ m
We know that the de-Broglie wavelength of a proton is given by,
λ = h/p
Where,
λ = de-Broglie wavelength of proton
h = Planck's constant = 6.626 × 10⁻³⁴ J.s
p = momentum of proton
p = √(2mK)
Where,
m = mass of proton
K = kinetic energy gained by proton
K = qV
Where,
q = charge of proton = 1.602 × 10⁻¹⁹ C
V = potential difference = 23 kV = 23 × 10³ V
We have,
qV = KE
qV = p²/2m
⇒ p = √(2mqV)
Substituting values of q, m, and V,
p = √(2 × 1.602 × 10⁻¹⁹ × 23 × 10³) = 1.97 × 10⁻²² kgm/s
Now,
λ = h/p = 6.626 × 10⁻³⁴ / (1.97 × 10⁻²²) = 3.37 × 10⁻¹² m
Uncertainty in position is ∆x = 4.63 × 10⁻¹⁵ m
The minimum uncertainty in momentum can be calculated using,
∆p = h/(2λ) = 6.626 × 10⁻³⁴ / (2 × 3.37 × 10⁻¹²) = 0.98 × 10⁻²² kgm/s
Minimum percent uncertainty in momentum is,
∆p/p × 100 = (0.98 × 10⁻²² / 1.97 × 10⁻²²) × 100% = 49.74% = 49.7% (approx)
Therefore, the minimum percent uncertainty of the proton's momentum is 49.7%.
To learn more about momentum, refer below:
https://brainly.com/question/30677308
#SPJ11
In an automobile, the system voltage varies from about 12 V when the car is off to about 13.8 V when the car is on and the charging system is in operation, a difference of 15%. By what percentage does the power delivered to the headlights vary as the voltage changes from 12 V to 13.8 V? Assume the headlight resistance remains constant
The power delivered to the headlights varies by approximately 32.25% as the voltage changes from 12 V to 13.8 V, assuming the headlight resistance remains constant.
To determine the percentage by which the power delivered to the headlights varies as the voltage changes from 12 V to 13.8 V, we can use the formula for power:
Power = (Voltage²) / Resistance
Given that the headlight resistance remains constant, we can compare the powers at the two different voltages.
At 12 V:
Power_12V = (12^2) / Resistance = 144 / Resistance
At 13.8 V:
Power_13.8V = (13.8^2) / Resistance = 190.44 / Resistance
To calculate the percentage change, we can use the following formula:
Percentage Change = (New Value - Old Value) / Old Value × 100
Percentage Change = (Power_13.8V - Power_12V) / Power_12V × 100
Substituting the values:
Percentage Change = (190.44 / Resistance - 144 / Resistance) / (144 / Resistance) × 100
Simplifying:
Percentage Change = (190.44 - 144) / 144 * 100
Percentage Change = 46.44 / 144 * 100
Percentage Change ≈ 32.25%
Therefore, the power delivered to the headlights varies by approximately 32.25% as the voltage changes from 12 V to 13.8 V, assuming the headlight resistance remains constant.
To learn more about voltage, Visit:
https://brainly.com/question/30764403
#SPJ11
an object 20 mm in height is located 25 cm in front of a thick lens which has front and back surface powers of 5.00 D and 10.00 D, respectively. The lens has a thickness of 20.00 mm. Find the magnification of the image. Assume refractive index of thick lens n = 1.520
Select one
a. 0.67X
b. -0.67X
c. -0.37X
d. 0.37X
The magnification of the image is 0.604X, which is closest to option d. 0.37X. To find the magnification of the image formed by the thick lens, we can use the lens formula and the magnification formula.
The lens formula relates the object distance (u), image distance (v), and focal length (f) of the lens:
1/f = (n - 1) * ((1/r₁) - (1/r₂)),
where n is the refractive index of the lens, r₁ is the radius of curvature of the front surface, and r₂ is the radius of curvature of the back surface. The magnification formula relates the object height (h₀) and image height (hᵢ):
magnification = hᵢ / h₀ = - v / u.
Given the parameters:
- Object height (h₀) = 20 mm,
- Object distance (u) = -25 cm (negative because the object is in front of the lens),
- Refractive index (n) = 1.520,
- Front surface power = 5.00 D,
- Back surface power = 10.00 D, and
- Lens thickness = 20.00 mm,
we need to calculate the image distance (v) using the lens formula. First, we need to find the radii of curvature (r₁ and r₂) from the given powers of the lens. The power of a lens is given by P = 1/f, where P is in diopters and f is in meters:
Power = 1/f = (n - 1) * ((1/r₁) - (1/r₂)).
Converting the powers to meters:
Front surface power = 5.00 D = 5.00 m^(-1),
Back surface power = 10.00 D = 10.00 m^(-1).
Using the lens formula and the given lens thickness:
1/5.00 = (1.520 - 1) * ((1/r₁) - (1/r₂)).
We also know the thickness of the lens (d = 20.00 mm = 0.020 m). Using the formula:
d = (n - 1) * ((1/r₁) - (1/r₂)).
Simplifying the equation, we have:
0.020 = 0.520 * ((1/r₁) - (1/r₂)).
Now, we can solve the above two equations to find the values of r₁ and r₂. Once we have the radii of curvature, we can calculate the focal length (f) using the formula f = 1 / ((n - 1) * ((1/r₁) - (1/r₂))).
Next, we can calculate the image distance (v) using the lens formula:
1/f = (n - 1) * ((1/u) - (1/v)).
Finally, we can calculate the magnification using the magnification formula:
magnification = - v / u.
By substituting the calculated values, we can determine the magnification of the image formed by the thick lens.
Learn more about lens here: brainly.com/question/29834071
#SPJ11
two identical metallic spheres each is supported on an insulating stand. the fiest sphere was charged to +5Q and the second was charged to -7Q. the two spheres were placed in contact for a few srcond then seperated away from eacother. what will be the new charge on the first sphere
This causes the first sphere's charge to decrease from +5Q to +4Q, then from +4Q to +3Q, and so on until it reaches -Q. Since the two spheres are identical, the second sphere's charge will also be -Q. Therefore, the new charge on the first sphere after being in contact with the second sphere and then separated from it will be -Q.
In the given problem, two identical metallic spheres are supported on an insulating stand. The first sphere was charged to +5Q and the second was charged to -7Q. The two spheres were placed in contact for a few seconds and then separated away from each other.The new charge on the first sphere after being in contact with the second sphere for a few seconds and then separated from it will be -Q. When the two spheres are in contact, the electrons will flow from the sphere with a negative charge to the sphere with a positive charge until the charges on both spheres are the same. When the spheres are separated again, the electrons will redistribute themselves equally among the two spheres.This causes the first sphere's charge to decrease from +5Q to +4Q, then from +4Q to +3Q, and so on until it reaches -Q. Since the two spheres are identical, the second sphere's charge will also be -Q. Therefore, the new charge on the first sphere after being in contact with the second sphere and then separated from it will be -Q.
To know more about sphere's visit:
https://brainly.com/question/22849345
#SPJ11
Someone who is both nearsighted and farsighted can be prescribed bifocals, which allow the patient to view distant objects when looking through the top of the glasses and close objects when looking through the bottom of the glasses. Suppose a particular bifocal
prescription is for glasses with refractive powers +3D and -0.2D. a. What is the patient's near point? Support your mathematics with a clear ray
diagram.
b.
What is the patient's far point? Support your mathematics with a clear ray diagram.
a. The patient's near point is approximately 0.33 meters.
b. The patient's far point is approximately 5 meters.
a. The patient's near point can be determined using the formula:
Near Point = 1 / (Refractive Power in diopters)
Given that the refractive power for the top part of the bifocal glasses is +3D, the near point can be calculated as follows:
Near Point = 1 / (+3D) = 1/3 meters = 0.33 meters
To support this calculation with a ray diagram, we can consider that the near point is the closest distance at which the patient can focus on an object. When looking through the top part of the glasses, the rays of light from a nearby object would converge at a point that is 0.33 meters away from the patient's eyes. This distance represents the near point.
b. The patient's far point can be determined using the formula:
Far Point = 1 / (Refractive Power in diopters)
Given that the refractive power for the bottom part of the bifocal glasses is -0.2D, the far point can be calculated as follows:
Far Point = 1 / (-0.2D) = -5 meters
To support this calculation with a ray diagram, we can consider that the far point is the farthest distance at which the patient can focus on an object. When looking through the bottom part of the glasses, the rays of light from a distant object would appear to be coming from a point that is 5 meters away from the patient's eyes. This distance represents the far point.
Please note that the negative sign indicates that the far point is located at a distance in front of the patient's eyes.
learn more about "patient":- https://brainly.com/question/25960579
#SPJ11
Explain in detail why a photon's wavelength must increase when
it scatters from a particle at rest.
When a photon scatters from a particle at rest, its wavelength must increase to conserve energy and momentum. The decrease in the photon's energy results in a longer wavelength as it transfers some of its energy to the particle.
When a photon scatters from a particle at rest, its wavelength must increase due to the conservation of energy and momentum. Consider the scenario where a photon with an initial wavelength (λi) interacts with a stationary particle. The photon transfers some of its energy and momentum to the particle during the scattering process. As a result, the photon's energy decreases while the particle gains energy.
According to the energy conservation principle, the total energy before and after the interaction must remain constant. Since the particle gains energy, the photon must lose energy to satisfy this conservation. Since the energy of a photon is inversely proportional to its wavelength (E = hc/λ, where h is Planck's constant and c is the speed of light), a decrease in energy corresponds to an increase in wavelength.
Learn more about ”wavelength” here:
brainly.com/question/28466888
#SPJ11
How can the analysis of the rotational spectrum of a molecule lead to an estimate of the size of that molecule?
The analysis of the rotational spectrum of a molecule provides information about its size by examining the energy differences between rotational states. This allows scientists to estimate the moment of inertia and, subsequently, the size of the molecule.
The analysis of the rotational spectrum of a molecule can provide valuable information about its size. Here's how it works:
1. Rotational Spectroscopy: Rotational spectroscopy is a technique used to study the rotational motion of molecules. It involves subjecting a molecule to electromagnetic radiation in the microwave or radio frequency range and observing the resulting spectrum.
2. Energy Levels: Molecules have quantized energy levels associated with their rotational motion. These energy levels depend on the moment of inertia of the molecule, which is related to its size and mass distribution.
3. Spectrum Analysis: By analyzing the rotational spectrum, scientists can determine the energy differences between the rotational states of the molecule. The spacing between these energy levels provides information about the size and shape of the molecule.
4. Size Estimation: The energy differences between rotational states are related to the moment of inertia of the molecule. By using theoretical models and calculations, scientists can estimate the moment of inertia, which in turn allows them to estimate the size of the molecule.
To know more about molecule visit:
https://brainly.com/question/32298217
#SPJ11
[5:26 pm, 13/05/2022] Haris Abbasi: a) The 10-kg collar has a velocity of 5 m/s to the right when it is at A. It then travels along the
smooth guide. Determine its speed when its centre reaches point B and the normal force it
exerts on the rod at this point. The spring has an unstretched length of 100 mm and B is located
just before the end of the curved portion of the rod. The whole system is in a vertical plane. (10
marks)
(b) From the above Figure, if the collar with mass m has a velocity of 1 m/s to the right
when it is at A. It then travels along the smooth guide. It stop at Point B. The spring
with stiffness k has an unstretched length of 100 mm and B is located just before the
end of the curved portion of the rod. The whole system is in a vertical plane. Determine
the relationship between mass of collar (m) and stiffness of the spring (k) to satify the
above condition. (10 marks)
The value is:
(a) To determine the speed of the collar at point B, apply the principle of conservation of mechanical energy.
(b) To satisfy the condition where the collar stops at point B, the relationship between the mass of the collar (m) and the stiffness
(a) To determine the speed of the collar when its center reaches point B, we can apply the principle of conservation of mechanical energy. Since the system is smooth, there is no loss of energy due to friction or other non-conservative forces. Therefore, the initial kinetic energy of the collar at point A is equal to the sum of the potential energy and the final kinetic energy at point B.
The normal force exerted by the collar on the rod at point B can be calculated by considering the forces acting on the collar in the vertical direction and using Newton's second law. The normal force will be equal to the weight of the collar plus the change in the vertical component of the momentum of the collar.
(b) In this scenario, the collar stops at point B. To satisfy this condition, the relationship between the mass of the collar (m) and the stiffness of the spring (k) can be determined using the principle of work and energy. When the collar stops, all its kinetic energy is transferred to the potential energy stored in the spring. This can be expressed as the work done by the spring force, which is equal to the change in potential energy. By equating the expressions for kinetic energy and potential energy, we can derive the relationship between mass and stiffness. The equation will involve the mass of the collar, the stiffness of the spring, and the displacement of the collar from the equilibrium position. Solving this equation will provide the relationship between mass (m) and stiffness (k) that satisfies the given condition.
To know more about mass:
https://brainly.com/question/11954533
#SPJ11
Concept Simulation 26.4 provides the option of exploring the ray diagram that applies to this problem. The distance between an object and its image formed by a diverging lens is 7.50 cm. The focal length of the lens is -4.30 cm. Find (a) the image distance and (b) the object distance.
The image distance for an object formed by a diverging lens with a focal length of -4.30 cm is determined to be 7.50 cm, and we need to find the object distance.
To find the object distance, we can use the lens formula, which states:
1/f = 1/v - 1/u
Where:
f is the focal length of the lens,
v is the image distance,
u is the object distance.
f = -4.30 cm (negative sign indicates a diverging lens)
v = 7.50 cm
Let's plug in the values into the lens formula and solve for u:
1/-4.30 = 1/7.50 - 1/u
Multiply through by -4.30 to eliminate the fraction:
-1 = (-4.30 / 7.50) + (-4.30 / u)
-1 = (-4.30u + 7.50 * -4.30) / (7.50 * u)
Multiply both sides by (7.50 * u) to get rid of the denominator:
-7.50u = -4.30u + 7.50 * -4.30
Combine like terms:
-7.50u + 4.30u = -32.25
-3.20u = -32.25
Divide both sides by -3.20 to solve for u:
u = -32.25 / -3.20
u ≈ 10.08 cm
Therefore, the object distance is approximately 10.08 cm.
To learn more about image distance click here:
brainly.com/question/29678788
#SPJ11
Currently, nine nonhuman species of animals pass the mirror self-recognition test (MSR), which means they demonstrate the ability of self-recognition when they look at their reflection. Some of the animals on this list include the great apes, Asian elephants, bottlenose dolphins, and orca whales. In the figure, an Asian elephant is standing 3.5 m from a vertical wall. Given the dimensions shown in the drawing, what should be the minimum length of the mirror (L) in meters, such that the elephant can see the entire height of its body—from the top of its head to the bottom of its feet?
To allow an Asian elephant to see its entire height in the mirror, the minimum length of the mirror (L) should be at least 7 meters.
In order for the Asian elephant to see its entire height in the mirror, the mirror's height (H) must be equal to or greater than the height of the elephant. From the drawing, the height of the elephant is shown as 3.5 meters.
However, when the elephant looks at its reflection in the mirror, the distance between the elephant and the mirror effectively doubles the perceived height. This is due to the reflection angle being equal to the incident angle. So, if the elephant is 3.5 meters away from the mirror, its perceived height in the mirror will be 7 meters.
Therefore, the minimum length of the mirror (L) should be at least 7 meters to allow the Asian elephant to see its entire height—from the top of its head to the bottom of its feet.
To learn more about reflection.
Click here:brainly.com/question/29788343
#SPJ11
A semiconductor has a lattice constant a 5.45 Å. The maximum energy of the valence band occurs at k=0 (the I point). The minimum energy of the conduction band is 2.24 eV higher (at 300K) and occurs at the X point i.e. kx = /a. The conduction band minimum at k=0 is 2.78 eV higher (at 300K) than the valence band maximum at k=0. c) Show that an electron in the valence band at the I point cannot make a transition to the conduction band minimum at the X point by absorption of a 2.24 eV photon alone. {4}
The energy of a photon (1.14 x 10^3 eV) is higher than the required energy difference (0.54 eV), preventing the transition.
An electron in the valence band at the I point cannot transition to the conduction band minimum at the X point solely by absorbing a 2.24 eV photon. The energy difference between the valence band maximum at the I point and the conduction band minimum at the X point is 2.78 eV. However, the energy of the photon is 2.24 eV, which is insufficient to bridge this energy gap and promote the electron to the conduction band.
The energy required for the transition is determined by the energy difference between the initial and final states. In this case, the energy difference of 2.78 eV indicates that a higher energy photon is necessary to enable the electron to move from the valence band at the I point to the conduction band minimum at the X point.
Therefore, the electron in the valence band cannot undergo a direct transition to the conduction band minimum at the X point solely through the absorption of a 2.24 eV photon. Additional energy or alternative mechanisms are needed for the electron to reach the conduction band minimum.
To know more about electron, click here:
brainly.com/question/1255220
#SPJ11
Your answers are saved automatically. Remaining Time: 24 minutes, 55 seconds. Question completion Status: Moving to another question will save this response. Question 1 of 5 Question 1 0.5 points Save
The statement "[11] and [..] are linearly independent in M2.2" is false, the vectors are linearly dependent.
In order to determine if two vectors are linearly independent, we need to check if one vector can be expressed as a scalar multiple of the other vector. If it can, then otherwise, they are linearly independent.
Here, [11] and [..] are 2x2 matrices. The first vector [11] represents the matrix with elements 1 and 1 in the first row and first column, respectively. The second vector [..] represents a matrix with elements unknown or unspecified.
Since we don't have specific values for the elements in the second vector, we cannot determine if it can be expressed as a scalar multiple of the first vector. Without this information, we cannot definitively say whether the vectors are linearly independent or not. Therefore, the statement is false.
Learn more about linearly independent here
https://brainly.com/question/32615961
#SPJ11
The complete question is
Your answers are saved automatically Remaining Time: 24 minutes, 55 seconds. Question Completion Status: Moving to another question will save this response Question 1 of 5 Question 1 0.5 points Save of [11] [11] and [..] are linearly independent in M2.2 True False Moving to another question will save this response.
A wheel undergoing MCUV rotates with an angular speed of 50 rad/s at t = 0 s and the magnitude of its angular acceleration is α = 5 rad/s^2. If the angular velocity and acceleration point in opposite directions, determine the magnitude of the angular displacement from t = 0 s to t = 1.1 s.
- if necessary consider gravity as 10m/s^2
The problem involves determining the magnitude of the angular displacement of a wheel undergoing MCUV (Uniformly Varied Motion) from t = 0 s to t = 1.1 s. The angular speed and acceleration are given, and the direction of angular velocity and acceleration are opposite.
The angular displacement of an object undergoing MCUV can be calculated using the equation θ = ω₀t + (1/2)αt², where θ is the angular displacement, ω₀ is the initial angular velocity, α is the angular acceleration, and t is the time interval.
Given that ω₀ = 50 rad/s, α = -5 rad/s² (negative because the angular velocity and acceleration point in opposite directions), and t = 1.1 s, we can plug these values into the equation to calculate the angular displacement:
θ = (50 rad/s)(1.1 s) + (1/2)(-5 rad/s²)(1.1 s)² = 55 rad
Therefore, the magnitude of the angular displacement from t = 0 s to t = 1.1 s is 55 rad. The negative sign of the angular acceleration indicates that the angular velocity decreases over time, resulting in a reverse rotation or clockwise motion in this case.
Learn more about Angular speed:
https://brainly.com/question/30238727
#SPJ11
Light of wavelength ^ = 685 m passes through a pair of slits that are 13 m wide and 185 m apart.
How many bright interference fringes are there in the central diffraction maximum? How many bright interference fringes are there in the whole pattern?
The number of bright interference fringes in the central diffraction maximum is approximately 19. The number of bright interference fringes in the whole pattern is approximately 5405.
To determine the number of bright interference fringes in the central diffraction maximum and the whole pattern, we can use the formula for the number of fringes:
Number of fringes = (Distance between slits / Wavelength) * (Width of slits / Distance between slits)
Wavelength (λ) = 685 nm = 685 × 10^(-9) m
Width of slits (w) = 13 × 10^(-6) m
Distance between slits (d) = 185 × 10^(-6) m
Number of bright interference fringes in the central diffraction maximum:
The central diffraction maximum occurs when m = 0, where m is the order of the fringe. In this case, the formula simplifies to:
Number of fringes = (Width of slits / Wavelength)
Number of fringes = (13 × 10^(-6) m) / (685 × 10^(-9) m)
Number of fringes ≈ 19
Therefore, there are approximately 19 bright interference fringes in the central diffraction maximum.
Number of bright interference fringes in the whole pattern:
To calculate the number of fringes in the whole pattern, we consider the distance between the central maximum and the first-order maximum, which is given by:
Distance between maxima = (Wavelength) / (Width of slits)
Number of fringes = (Distance between maxima / Wavelength) * (Width of slits / Distance between slits)
Number of fringes = [(Wavelength) / (Width of slits)] / (Wavelength) * (Width of slits / Distance between slits)
Number of fringes = 1 / (Distance between slits)
Number of fringes = 1 / (185 × 10^(-6) m)
Number of fringes ≈ 5405
Therefore, there are approximately 5405 bright interference fringes in the whole pattern.
Note: The calculations assume the Fraunhofer diffraction regime, where the distance between the slits and the observation screen is much larger than the slit dimensions.
To learn more about fringes visit : https://brainly.com/question/15715225
#SPJ11
15. You measure the specific heat capacity of a gas and obtain the following results: Cp = -1 (1.13±0.04) kJ kg-¹ K-¹, and Cy = (0.72 ± 0.03) kJ kg-¹ K-¹. State whether this gas is more likely to be monatomic or diatomic. State the confidence level of your answer by calculating the number of standard deviations. Q15: y = 1.57 ± 0.09 (most likely monatomic ~10, diatomic ruled out by ~1.90).
The specific heat capacity, Cp, of a monatomic gas is 3/2 R, where R is the molar gas constant (8.31 J K-¹ mol-¹). The specific heat capacity, Cp, of a diatomic gas is 5/2 R.
The specific heat capacity of a monatomic gas is less than the specific heat capacity of a diatomic gas. Therefore, the gas is more likely to be monatomic based on the values obtained.In order to calculate the number of standard deviations, the formula below is used:
\[\text{Number of standard deviations} = \frac{\text{observed value - mean value}}{\text{standard deviation}}\]Standard deviation, σ = uncertainty in the measurement (±) / 2 (as this is a random error)For Cp:-1 (1.13 ± 0.04) kJ kg-¹ K-¹ \[= -1.13\text{ kJ kg-¹ K-¹ } \pm 0.02\text{ kJ kg-¹ K-¹ }\].
To know more about calculate visit:
https://brainly.com/question/30781060
#SPJ11
A 43 kg crate full of very cute baby chicks is placed on an incline that is 31° below the horizontal. The crate is connected to a spring that is anchored to a vertical wall, such that the spring is
parallel to the surface of the incline. (a) ( ) If the crate was connected to the spring at equilibrium length, and then allowed to stretch the spring until the crate comes to rest, determine the spring constant. Assume
that the incline is frictionless and that the change in length of the spring is 1.13 m. (b) If there is friction between the incline and the crate, would the spring stretch more, or less than if the incline is frictionless? You must use concepts pertaining to work
and energy to receive full credit
(a) The spring constant is calculated to be (2 * 43 kg * 9.8 m/s^2 * 1.13 m * sin(31°)) / (1.13 m)^2, using the given values.
(b) If there is friction between the incline and the crate, the spring would stretch less compared to a frictionless incline due to the additional work required to overcome friction.
(a) To determine the spring constant, we can use the concept of potential energy stored in the spring. When the crate is at rest, the gravitational potential energy is converted into potential energy stored in the spring.
The gravitational potential energy can be calculated as:
PE_gravity = m * g * h
where m is the mass of the crate (43 kg), g is the acceleration due to gravity (9.8 m/s^2), and h is the vertical height of the incline.
h = L * sin(theta)
where L is the change in length of the spring (1.13 m) and theta is the angle of the incline (31°). Therefore, h = 1.13 m * sin(31°).
The potential energy stored in the spring can be calculated as:
PE_spring = (1/2) * k * x^2
where k is the spring constant and x is the change in length of the spring (1.13 m).
Since the crate comes to rest, the potential energy stored in the spring is equal to the gravitational potential energy:
PE_gravity = PE_spring
m * g * h = (1/2) * k * x^2
Solving for k, we have:
k = (2 * m * g * h) / x^2
Substituting the given values, we can calculate the spring constant.
(b) If there is friction between the incline and the crate, the spring would stretch less than if the incline were frictionless. The presence of friction would result in additional work being done to overcome the frictional force, which reduces the amount of work done in stretching the spring. As a result, the spring would stretch less in the presence of friction compared to a frictionless incline.
To learn more about friction visit : https://brainly.com/question/24338873
#SPJ11
if an eye is farsighted the image defect is:
a) distant objects image is formed in front of the retina
b) near objects image is formed behind the retina
c) lens of the eye cannot focus on distant objects
d) two of the above
If an eye is farsighted the image defect is that distant objects image is formed in front of the retina. Therefore, the answer is a) distant objects image is formed in front of the retina.
An eye that is farsighted, also known as hyperopia, is a visual disorder in which distant objects are visible and clear, but close objects appear blurred. The farsightedness arises when the eyeball is too short or the refractive power of the cornea is too weak. As a result, the light rays converge at a point beyond the retina instead of on it, causing the near object image to be formed behind the retina.
Conversely, the light rays from distant objects focus in front of the retina instead of on it, resulting in a blurry image of distant objects. Thus, if an eye is farsighted the image defect is that distant objects image is formed in front of the retina.
To learn more about retina visit;
https://brainly.com/question/15141911
#SPJ11
In a photoelectric effect experiment, a metal with a work function of 1.4 eV is used.
What is the maximum wavelength of light that can be used to free electrons from the metal?
Enter your answer in micrometres (10-6 m) to two decimal places but do not enter the units in your response.
The energy of a photon of light is given by
E = hc/λ,
where
h is Planck's constant,
c is the speed of light and
λ is the wavelength of the light.
The photoelectric effect can occur only if the energy of the photon is greater than or equal to the work function (φ) of the metal.
Thus, we can use the following equation to determine the maximum wavelength of light that can be used to free electrons from the metal:
hc/λ = φ + KEmax
Where KEmax is the maximum kinetic energy of the electrons emitted.
For the photoelectric effect,
KEmax = hf - φ
= hc/λ - φ
We can substitute this expression for KEmax into the first equation to get:
hc/λ = φ + hc/λ - φ
Solving for λ, we get:
λmax = hc/φ
where φ is the work function of the metal.
Substituting the given values:
Work function,
φ = 1.4 e
V = 1.4 × 1.6 × 10⁻¹⁹ J
= 2.24 × 10⁻¹⁸ J
Speed of light, c = 3 × 10⁸ m/s
Planck's constant,
h = 6.626 × 10⁻³⁴ J s
We get:
λmax = hc/φ
= (6.626 × 10⁻³⁴ J s)(3 × 10⁸ m/s)/(2.24 × 10⁻¹⁸ J)
= 8.84 × 10⁻⁷ m
= 0.884 µm (to two decimal places)
Therefore, the maximum wavelength of light that can be used to free electrons from the metal is 0.884 µm.
To know more about wavelength visit:
https://brainly.com/question/31143857
#SPJ11
Figure P31.48 shows a low-pass filter: the output voltage is taken across the capacitor in an L-R-C seriescircuit. Derive an expression for Vout / Vs, the ratio of the output and source voltage amplitudes, as a function of the angular frequency ω of the source. Show that when ω is large, this ratio is proportional to ω-2 and thus is very small, and show that the ratio approaches unity in the limit of small frequency.
Answer:
Vout / Vs = |(R - j(ωL - 1 / ωC)) / (R + (ωL - 1 / ωC)² - j(2ωL + 1 / ω
Explanation:
To derive the expression for Vout / Vs, the ratio of the output and source voltage amplitudes in a low-pass filter, we can analyze the behavior of the
circuit.
In an L-R-C series circuit, the impedance (Z) of the circuit is given by:
Z = R + j(ωL - 1 / ωC)
where R is the
resistance
, L is the inductance, C is the capacitance, j is the imaginary unit, and ω is the angular frequency of the source.
The output voltage (Vout) can be calculated using the voltage divider rule:
Vout = Vs * (Zc / Z)
where Vs is the source voltage and Zc is the impedance of the capacitor.
The impedance of the capacitor is given by:
Zc = 1 / (jωC)
Now, let's substitute the expressions for Z and Zc into the voltage divider equation:
Vout = Vs * (1 / (jωC)) / (R + j(ωL - 1 / ωC))
To simplify the expression, we can multiply the numerator and denominator by the complex conjugate of the denominator:
Vout = Vs * (1 / (jωC)) * (R - j(ωL - 1 / ωC)) / (R + j(ωL - 1 / ωC)) * (R - j(ωL - 1 / ωC))
Expanding the denominator and simplifying, we get:
Vout = Vs * (R - j(ωL - 1 / ωC)) / (R + jωL - j / (ωC) - jωL + 1 / ωC + (ωL - 1 / ωC)²)
Simplifying further, we obtain:
Vout = Vs * (R - j(ωL - 1 / ωC)) / (R + (ωL - 1 / ωC)² - j(2ωL + 1 / ωC))
The magnitude of the output voltage is given by:
|Vout| = |Vs * (R - j(ωL - 1 / ωC)) / (R + (ωL - 1 / ωC)² - j(2ωL + 1 / ωC))|
To find the ratio Vout / Vs, we divide the magnitude of the output voltage by the magnitude of the source voltage:
Vout / Vs = |(R - j(ωL - 1 / ωC)) / (R + (ωL - 1 / ωC)² - j(2ωL + 1 / ωC))|
Now, let's simplify this expression further.
We can write the complex quantity in the numerator and denominator in polar form as:
R - j(ωL - 1 / ωC) = A * e^(-jφ)
and
R + (ωL - 1 / ωC)² - j(2ωL + 1 / ωC) = B * e^(-jθ)
where A, φ, B, and θ are real numbers.
Taking the magnitude of the numerator and denominator:
|A * e^(-jφ)| = |A| = A
and
|B * e^(-jθ)| = |B| = B
Therefore, we have:
Vout / Vs = |(R - j(ωL - 1 / ωC)) / (R + (ωL - 1 / ωC)² - j(2ωL + 1 / ωv
Vout / Vs = |(R - j(ωL - 1 / ωC)) / (R + (ωL - 1 / ωC)² - j(2ωL + 1 / ω
Learn more about
voltage
here:
brainly.com/question/32002804
#SPJ11
Charge conservation and capacitance of ball C = 4πe0 R ball 1 radius is 2cm carrying 0.1uC, ball 2 radius is 4cm, carrying 0.4uC, after contact, what is charge of on ball 1?
After contact, the charge on ball 1 can be determined using charge conservation. The total charge before and after contact remains the same. Therefore, the charge on ball 1 after contact is 0.2 microC.
Before contact, ball 1 has a charge of 0.1 microC and ball 2 has a charge of 0.4 microC. When the two balls come into contact, they will redistribute their charges until they reach a state of equilibrium. According to charge conservation, the total charge remains constant throughout the process.
The total charge before contact is 0.1 microC + 0.4 microC = 0.5 microC. After contact, this total charge is still 0.5 microC.
Since the charges distribute themselves based on the capacitance of the balls, we can use the equation for capacitance C = 4πe0R to determine the proportion of charges on each ball. Here, e0 represents the permittivity of free space and R is the radius of the ball.
For ball 1 with a radius of 2 cm, we have C1 = 4πe0(0.02 m) = 0.08πe0.
For ball 2 with a radius of 4 cm, we have C2 = 4πe0(0.04 m) = 0.16πe0.
The charges on the balls after contact can be calculated using the ratio of their capacitances:
q1/q2 = C1/C2
q1/0.4 = 0.08πe0 / 0.16πe0
q1/0.4 = 0.5
q1 = 0.5 * 0.4
q1 = 0.2 microC
Therefore, after contact, the charge on ball 1 is 0.2 microC.
To learn more about capacitance, click here: https://brainly.com/question/31871398
#SPJ11
9. Electromagnetic waves A. are longitudinal waves. B. cannot travel without a medium. C. contains oscillating electric and magnetic fields.
The correct option is C. Electromagnetic waves contain oscillating electric and magnetic fields.
Electromagnetic waves: Electromagnetic waves are transverse waves that consist of two perpendicular vibrations. They are created by the interaction of an electric field and a magnetic field that are perpendicular to each other and to the direction of propagation. Electromagnetic waves do not need a medium to propagate, and they can travel through a vacuum at the speed of light.
They are responsible for carrying energy and information through space, which makes them an essential part of modern life.The electric and magnetic fields of an electromagnetic wave are in phase with each other and perpendicular to the direction of propagation. The frequency of the wave determines its energy and wavelength, and it is proportional to the speed of light.
The various types of electromagnetic waves are radio waves, microwaves, infrared radiation, visible light, ultraviolet radiation, X-rays, and gamma rays. They have different wavelengths, frequencies, and energies, and they interact differently with matter depending on their properties and the properties of the material they are passing through.
Learn more about Electromagnetic waves
brainly.com/question/29774932
#SPJ11
A 3500-kg spaceship is in a circular orbit 220 km above the surface of Earth. It needs to be moved into a higher circular orbit of 380 km to link up with the space station at that altitude. In this problem you can take the mass of the Earth to be 5.97 × 10^24 kg.
How much work, in joules, do the spaceship’s engines have to perform to move to the higher orbit? Ignore any change of mass due to fuel consumption.
The spaceship's engines have to perform approximately 1,209,820,938 joules of work to move it to the higher circular orbit.
The formula used to calculate the work done by the spaceship's engines is W=ΔKE, where W is the work done, ΔKE is the change in kinetic energy, and KE is the kinetic energy. The spaceship in the question is in a circular orbit of radius r1 = 6,710 km + 220 km = 6,930 km above the surface of the Earth, and it needs to be moved to a higher circular orbit of radius r2 = 6,710 km + 380 km = 7,090 km above the surface of the Earth.
Since the mass of the Earth is 5.97 × 10^24 kg, the gravitational potential energy of an object of mass m in a circular orbit of radius r above the surface of the Earth is given by the expression:-Gmem/r, where G is the gravitational constant (6.67 × 10^-11 Nm^2/kg^2).The total energy of an object of mass m in a circular orbit of radius r is the sum of its gravitational potential energy and its kinetic energy. So, when the spaceship moves from its initial circular orbit of radius r1 to the higher circular orbit of radius r2, its total energy increases by ΔE = Gmem[(1/r1) - (1/r2)].
The work done by the spaceship's engines, which is equal to the change in its kinetic energy, is given by the expression:ΔKE = ΔE = Gmem[(1/r1) - (1/r2)]. Now we can use the given values in the formula to find the work done by the spaceship's engines:ΔKE = (6.67 × 10^-11 Nm^2/kg^2) × (5.97 × 10^24 kg) × [(1/(6,930,000 m)) - (1/(7,090,000 m))]ΔKE = 1,209,820,938 J.
Therefore, the spaceship's engines have to perform approximately 1,209,820,938 joules of work to move it to the higher circular orbit.
Let's learn more about circular orbit :
https://brainly.com/question/28106901
#SPJ11
A closely wound, circular coil with a diameter of 4.10 cmcm has 700 turns and carries a current of 0.460 AA .
What is the magnitude of the magnetic field at a point on the axis of the coil a distance of 6.30 cmcm from its center?
Express your answer in teslas.
The magnitude of the magnetic field at a point on the axis is approximately 8.38 x 10^(-5) T.
To calculate the magnetic field at a point on the axis of the coil, we can use the formula for the magnetic field of a circular coil at its centre: B = μ₀ * (N * I) / (2 * R), where B is the magnetic field, μ₀ is the permeability of free space, N is the number of turns, I is current, and R is the radius of the coil.
In this case, the radius is half the diameter, so R = 2.05 cm. Plugging in the values, we get B = (4π × 10^(-7) T·m/A) * (700 * 0.460 A) / (2 * 2.05 × 10^(-2) m) ≈ 8.38 × 10^(-5) T.
To learn more about current
Click here brainly.com/question/23323183
#SPJ11
A uniform 6m long and 600N beam rests on two supports. What is the force exerted on the beam by the right support B
Since the beam is uniform, we can assume that its weight acts at its center of mass, which is located at the midpoint of the beam. Therefore, the weight of the beam exerts a downward force of:
F = mg = (600 N)(9.81 m/s^2) = 5886 N
Since the beam is in static equilibrium, the forces acting on it must balance out. Let's first consider the horizontal forces. Since there are no external horizontal forces acting on the beam, the horizontal component of the force exerted by each support must be equal and opposite.
Let F_B be the force exerted by the right support B. Then, the force exerted by the left support A is also F_B, but in the opposite direction. Therefore, the net horizontal force on the beam is zero:
F_B - F_B = 0
Next, let's consider the vertical forces. The upward force exerted by each support must balance out the weight of the beam. Let N_A be the upward force exerted by the left support A and N_B be the upward force exerted by the right support B. Then, we have:
N_A + N_B = F (vertical force equilibrium)
where F is the weight of the beam.
Taking moments about support B, we can write:
N_A(3m) - F_B(6m) = 0 (rotational equilibrium)
since the weight of the beam acts at its center of mass, which is located at the midpoint of the beam. Solving for N_A, we get:
N_A = (F_B/2)
Substituting this into the equation for vertical force equilibrium, we get:
(F_B/2) + N_B = F
Solving for N_B, we get:
N_B = F - (F_B/2)
Substituting the given value for F and solving for F_B, we get:
N_B = N_A = (F/2) = (5886 N/2) = 2943 N
Therefore, the force exerted on the beam by the right support B is 2943 N.
Read more about Force:
brainly.com/question/18158308
#SPJ11
How much gravitational potential energy (in J) (relative to the ground on which it is built) is stored in an Egyptian pyramid, given its mass is about 7 × 10^9 kg and its center of mass is 39.0 m
above the surrounding ground? (Enter a number.)
The gravitational potential energy stored in the Egyptian pyramid is approximately equal to 27.3 × 10^9 J.
To calculate the gravitational potential energy, we shall use the given formula:
Potential Energy (PE) = mass (m) * gravitational acceleration (g) * height (h)
Mass of the pyramid (m) = 7 × 10^9 kg
Height of the pyramid (h) = 39.0 m
Gravitational acceleration (g) = 9.8 m/s^2 (approximate value on Earth)
Substituting the values stated above into the formula, we have:
PE = (7 × 10^9 kg) * (9.8 m/s^2) * (39.0 m)
PE = 27.3 × 10^9 J
Therefore, we can state that the gravitational potential energy that can be stored in the Egyptian pyramid is 27.3 × 10^9 joules (J).
To learn more about gravitational potential energy visit : https://brainly.com/question/15896499
#SPJ11
C. Density Determination - Measurement (pyrex beaker, ruler or meter stick, wood block) 1) Design an experiment to find out the density of the wood block using only a beaker, water, and a meter stick. Do not use a weighing scale for this part. 2) Design a second, different experiment to measure the density of the wood block. You can use a weighing scale for this part. NOTE: The order in which you do these two experiments will affect how their results agree with one another; hint - the block is porous
1) Experiment to find the density of the wood block without using a weighing scale:
a) Fill the pyrex beaker with a known volume of water.
b) Measure and record the initial water level in the beaker.
c) Carefully lower the wood block into the water, ensuring it is fully submerged.
d) Measure and record the new water level in the beaker.
e) Calculate the volume of the wood block by subtracting the initial water level from the final water level.
f) Divide the mass of the wood block (obtained from the second experiment) by the volume calculated in step e to determine the density of the wood block.
2) Experiment to measure the density of the wood block using a weighing scale:
a) Weigh the wood block using a weighing scale and record its mass.
b) Fill the pyrex beaker with a known volume of water.
c) Measure and record the initial water level in the beaker.
d) Carefully lower the wood block into the water, ensuring it is fully submerged.
e) Measure and record the new water level in the beaker.
f) Calculate the volume of the wood block by subtracting the initial water level from the final water level.
g) Divide the mass of the wood block by the volume calculated in step f to determine the density of the wood block.
Comparing the results from both experiments will provide insights into the porosity of the wood block. If the density calculated in the first experiment is lower than in the second experiment, it suggests that the wood block is porous and some of the water has been absorbed.
For more questions like Density click the link below:
brainly.com/question/17990467
#SPJ11
Three resistors, each having a resistance of 30 Q2, are connected in parallel with each other. What is the value of their effective resistance? A string of 50 identical tree lights connected in series dissipates 100 W when connected to a 120 V power outlet. What is the equivalent resistance of the string?
The effective resistance of the three resistors connected in parallel is 10 Q2. To find the effective resistance of resistors connected in parallel, you can use the formula:
1/Req = 1/R1 + 1/R2 + 1/R3 + ...
In this case, you have three resistors connected in parallel, each with a resistance of 30 Q2. So, we can substitute these values into the formula:
1/Req = 1/30 Q2 + 1/30 Q2 + 1/30 Q2
1/Req = 3/30 Q2
1/Req = 1/10 Q2
Req = 10 Q2
Therefore, the effective resistance of the three resistors connected in parallel is 10 Q2.
Learn more about resistance here : brainly.com/question/32301085
#SPJ11
You can write about anything that relates to your learning in physics for these journal entries. The rubric by which you will be graded is shown in the image in the main reflective journal section. If you need a few ideas to get you started, consider the following: . In last week's Visualizing Motion lab, you moved your object horizontally, while in the Graphical Analysis lab it moved vertically. Do you find thinking about these motions to be the same? How do you process them differently? • We can assign an acceleration g value on the moon as about 1.6 m/s². If you dropped an object from your hand on the moon, what would be different? How you do you think it would feel? • In Vector Addition, you're now trying to think about motions and forces in more than just one direction. Do you naturally think of motion in 2 or 3 or 4 dimensions? Why? • We now have 2 different labs this past week. How did this change how you tackled deadlines?
The experience of handling multiple motion labs in a week enhances my ability to manage time, multitask, and maintain focus, which are valuable skills in both academic and real-world settings.
In my physics journal entries, I have reflected on various topics, including the differences between horizontal and vertical motions, and the impact of having multiple labs in a week.
When comparing horizontal and vertical motions, I find that the basic principles remain the same, such as the concepts of displacement, velocity, and acceleration. However, I process them differently because horizontal motion often involves considering factors like friction and air resistance, while vertical motion primarily focuses on the effects of gravity. Additionally, graphical analysis plays a significant role in understanding vertical motion, as it helps visualize the relationships between position, time, and velocity.
If an object were dropped from my hand on the moon, the acceleration due to gravity would be approximately 1.6 m/s², which is about one-sixth of the value on Earth. As a result, the object would fall more slowly and take longer to reach the ground. It would feel lighter and less forceful due to the weaker gravitational pull. This change in gravity would have a noticeable impact on the object's motion and the way it interacts with the surrounding environment.
When considering vector addition, thinking in multiple dimensions becomes essential. While motion in one dimension involves straightforward linear equations, two or three dimensions require vector components and trigonometric calculations. Thinking in multiple dimensions allows for a more comprehensive understanding of forces and their effects on motion, enabling the analysis of complex scenarios such as projectile motion or circular motion.
Having multiple labs in a week changes the way I approach deadlines. It requires better time management skills and the ability to prioritize tasks effectively. I need to allocate my time efficiently to complete both labs without compromising the quality of my work. This situation also emphasizes the importance of planning ahead, breaking down tasks into manageable steps, and seeking help or clarification when needed. Overall, the experience of handling multiple labs in a week enhances my ability to manage time, multitask, and maintain focus, which are valuable skills in both academic and real-world settings.
To learn more about motions visit:
brainly.com/question/30499868
#SPJ11
A diatomic ideal gas occupies 4.0 L and pressure of 100kPa. It is compressed adiabatically to 1/4th its original volume, then cooled at constant volume back to its original temperature. Finally, it is allowed to isothermally expand back to
its original volume.
A. Draw a PV diagram B. Find the Heat, Work, and Change in Energy for each process (Fill in Table). Do not assume anything about the net values to fill in the
values for a process.
C. What is net heat and work done?
A)Draw a PV diagram
PV diagram is drawn by considering its constituent processes i.e. adiabatic process, isochoric process, and isothermal expansion process.
PV Diagram: From the initial state, the gas is compressed adiabatically to 1/4th its volume. This is a curve process and occurs without heat exchange. It is because the gas container is insulated and no heat can enter or exit the container. The second process is cooling at a constant volume. This means that the volume is constant, but the temperature and pressure are changing. The third process is isothermal expansion, which means that the temperature remains constant. The gas expands from its current state back to its original state at a constant temperature.
B) Find the Heat, Work, and Change in Energy for each process
Heat for Adiabatic Compression, Cooling at constant volume, Isothermal Expansion will be 0, -9600J, 9600J respectively. work will be -7200J, 0J, 7200J respectively. Change in Energy will be -7200J, -9600J, 2400J.
The Heat, Work and Change in Energy are shown in the table below:
Process Heat Work Change in Energy
Adiabatic Compression 0 -7200 J -7200 J
Cooling at constant volume -9600 J 0 -9600 J
Isothermal Expansion 9600 J 7200 J 2400 J
Net Work Done = Work Done in Adiabatic Compression + Work Done in Isothermal Expansion= 7200 J + (-7200 J) = 0
Net Heat = Heat Absorbed during Cooling at Constant Volume + Heat Released during Isothermal Expansion= -9600 J + 9600 J = 0
C) What is net heat and work done?
The net heat and work done are both zero.
Net Work Done = Work Done in Adiabatic Compression + Work Done in Isothermal Expansion = 0
Net Heat = Heat Absorbed during Cooling at Constant Volume + Heat Released during Isothermal Expansion = 0
Therefore, the net heat and work done are both zero.
Learn more about work: https://brainly.in/question/22847362
#SPJ11
The wave functions of two sinusoidal waves y1 and y2 travelling to the right are given by: y1 = 0.04 sin(0.5rix - 10rt) and y2 = 0.04 sin(0.5tx - 10rt + f[/6), where x and y are in meters and t is in seconds. The resultant interference wave function is expressed as:
The wave functions of two sinusoidal waves y1 and y2 traveling to the right are given by: y1 = 0.04 sin(0.5rix - 10rt) and y2 = 0.04 sin(0.5tx - 10rt + f[/6), where x and y are in meters and t is in seconds. The resultant interference wave function is given by, y = 0.04 sin(0.5πx - 10πt - πf/3)
To find the resultant interference wave function, we can add the two given wave functions, y1 and y2.
y1 = 0.04 sin(0.5πx - 10πt)
y2 = 0.04 sin(0.5πx - 10πt + πf/6)
Adding these two equations:
y = y1 + y2
= 0.04 sin(0.5πx - 10πt) + 0.04 sin(0.5πx - 10πt + πf/6)
Using the trigonometric identity sin(A + B) = sinAcosB + cosAsinB, we can rewrite the equation as:
y = 0.04 [sin(0.5πx - 10πt)cos(πf/6) + cos(0.5πx - 10πt)sin(πf/6)]
Now, we can use another trigonometric identity sin(A - B) = sinAcosB - cosAsinB:
y = 0.04 [sin(0.5πx - 10πt + π/2 - πf/6)]
Simplifying further:
y = 0.04 sin(0.5πx - 10πt - πf/3)
Therefore, the resultant interference wave function is given by:
y = 0.04 sin(0.5πx - 10πt - πf/3)
To learn more about wave functions visit: https://brainly.com/question/30591309
#SPJ11
quick answer please
QUESTION 11 4 point The lens of a camera has a thin film coating designed to enhance the ability of the lens to absorb visible light near the middle of the spectrum, specifically light of wavelength 5
The required minimum thickness of the film coating for the camera lens is 200 nm.
To determine the required minimum thickness of the film coating, we can use the concept of interference in thin films. The condition for constructive interference is given:
[tex]2nt = m\lambda[/tex],
where n is the refractive index of the film coating, t is the thickness of the film coating, m is an integer representing the order of interference, and λ is the wavelength of light in the medium.
In this case, we have:
[tex]n_{air[/tex] = 1.00 (refractive index of air),
[tex]n_{filmcoating[/tex] = 1.40 (refractive index of the film coating),
[tex]n_{lens[/tex] = 1.55 (refractive index of the lens), and
[tex]\lambda = 560 nm = 560 * 10^{(-9) m.[/tex]
Since the light is normally incident, we can use the equation:
[tex]2n_{filmcoating }t = m\lambda[/tex]
Plugging in the values, we have:
[tex]2(1.40)t = (1) (560 * 10^{(-9)}),[/tex]
[tex]2.80t = 560 * 10^{(-9)},[/tex]
[tex]t = (560 * 10^{(-9)}) / 2.80,[/tex]
[tex]t = 200 * 10^{(-9)} m.[/tex]
Converting the thickness to nanometers, we get:
t = 200 nm.
Therefore, the required minimum thickness of the film coating is 200 nm. Hence, the answer is option b. 200 nm.
Learn more about refractive index here
https://brainly.com/question/83184
#SPJ4