Air at 1.00 atm is passed through a horizontal 1.5-in. Schedule 40 (steam-jacketed) steel pipe at a velocity of 2.10 ft/s and an inlet and outlet temperature of 25.0 °C and 95.5 °C, respectively. The pipe wall temperature is maintained at 121.1 °C. (HINT: You may neglect the viscosity correction in your calculations.) a) Assuming only heat transfer by forced convection, how long must

Answer:

missing question; How long must the heated section be

answer : 5.898 meters

Explanation:

Given parameters:

Diameter of steel pipe = 1.5 inches = 0.0381 m

velocity of air = 2.10 ft/s = 0.64 m/s

Inlet temperature = 25°C

Outlet temperature = 95.5°C

pipe wall temperature = 121.1°C

Average temperature = ( 25 + 95.5 ) / 2 = 60.25°

determine Reynolds number of air at 60.25°

= VD / v = ( 0.64 * 0.0381 ) / ( 1.83 * 10^-5 )

              = 1332.46  this means the flow is laminar

hence mass flow rate ( m ) = eAv = 1.08 * πd^2 * velocity

= 1.08 * 0.0046 * 0.64 = 0.0032 g/s

attached below is the remaining part of the solution

name the process by which mild steel can be converted into high carbon steel and explain it briefly ?​

(TCO 3) Below is the frequency response of the IIR realization of an analog band-pass filter. What type of filter is this?

180 kg/h of a liquid feed enters an extraction column with 98% paraffin oil and 2% ethyl alcohol at room temperature and pressure. Liquid absorbent is 100% water. Required recovery (extraction) of ethyl alcohol from paraffin oil is 97%. Given that paraffin oil and water are immiscible with each other and the extraction column operates in a counter current fashion. Assume isothermal and isobaric conditions and that only ethyl alcohol is absorbed. Equilibrium relation between mass fractions of ethyl alcohol in water and paraffin oil is given by Xwater = 1.7544 * Xparaffin oil (a) Find minimum amount of water required (Answer – 97.5 kg/hr) (b) If you have 1.5 times minimum water amount, how many equilibrium stages are required? (Answer ~ 6)

If we want to create a single function for insertion and deletion in the linked list, Suggest any approach by which this task can be carried out. Just verbally explain how we can accomplish this, no need to write the code

Air enters the combustor of a jet engine at Pressure=10 atm, T=1000R and M=0.2. Fuel is injected and burned with fuel-air ratio (by mass) of 0.06. The heat released during the combustion is 4.50000000 ft-lb per slug of fuel. Assuming one-dimensional frictionless flow with r=1.4 for the fuel-air mixture, calculate M2, p2 and T2 at the exit of combustor?

Switching to first order kinetics, enzymes are immobilized in 6 mm radius (R) beads. Beads are immersed in a solution containing substrate at a concentration (CAs) of 22 gmol/m3. The observed reaction rate (rA,obs) of the heterogeneous reaction is 4.3 x 10-6 gmol/sec. The first order rate constant (k1) is 0.24 /sec. Calculate the hypothetical rate, r*As of the reaction in this system.

Iman wanted to find out at what temperature butter melts. She placed a cube of solid butter in a beaker. She put the beaker on a hot plate. She turned up the temperature dial one degree every two minutes. Then she recorded the temperature at which the butter started to melt.

Iman wanted to determine if her results were reliable. She decided to repeat the experiment. Which statement describes the main purpose of repeating the experiment?


to test a different substance

to see if the results are similar

to practice completing experiments

to determine if butter will melt twice