a) To design a lossless T-junction power divider for a 3:1 power split with a 30Ω source impedance, we can use equal-value resistors in the T-junction. The diagram would consist of a single input line connected to a T-shaped junction, with two output lines. One output line will have a resistor of 30Ω connected to it, and the other output line will have two resistors of equal value, each representing 60Ω.
b) To transform the impedance of the output lines to 30Ω, we can use quarter-wave matching transformers. Each output line would require a quarter-wave transmission line with an impedance transformation ratio of 2:1. This will match the output lines' impedance to 30Ω. The quarter-wave matching transformers can be implemented using transmission lines or lumped components, depending on the frequency range of operation.
c) To determine the magnitude of the scattering parameters (S-parameters) for this circuit with a 30Ω characteristic impedance, we would need the S-parameter matrix for the T-junction power divider. The S-parameters represent the power transfer between the input and output ports. The magnitude of the S-parameters can be determined by taking the absolute value of each element in the S-parameter matrix. The resulting magnitudes would provide the information about power transfer and isolation between the ports of the T-junction power divider.
To know more about visit-
https://brainly.com/question/33224727
#SPJ11
1 kg/s of steam enters a control volume at 10MPa and 800 C. It exits at 4MPa and 400 C. The control volume communicates with a sink at 27 C. What is the maximum work that can be obtained from the flowing stream?
In a control volume, 1 kg/s of steam enters at 10 MPa and 800°C and exits at 4 MPa and 400°C. The control volume is in communication with a sink at 27°C. The objective is to determine the maximum work that can be obtained from the flowing stream.
To calculate the maximum work that can be obtained from the flowing stream, we need to analyze the thermodynamic properties of the steam and apply the principles of energy conservation. The maximum work that can be obtained corresponds to the difference in exergy between the initial and final states of the steam. Exergy represents the maximum useful work that can be extracted from a system when it is brought into equilibrium with the surroundings. The exergy of the steam at the inlet and outlet can be calculated using the equations: Ex = h - T0 * s, where Ex represents exergy, h is the specific enthalpy, T0 is the reference temperature (in this case, the sink temperature), and s is the specific entropy. By calculating the exergy at the inlet and outlet states, and considering the mass flow rate, we can determine the maximum work that can be obtained from the flowing stream using the equation: W = m * (Ex_inlet - Ex_outlet). Substituting the known values and performing the necessary calculations, we can find the maximum work that can be obtained from the flowing stream.
Learn more about equilibrium here:
https://brainly.com/question/30742399
#SPJ11
Example – draw a value stream map for the following toy manufacturing: Monthly orders from client Weekly orders to suppliers Weekly production schedule Weekly inventory delivery from suppliers • Three production processes: -Assembly -Painting, fitments & other cosmetics -Testing
• Assembly -Lead time 4hr, C/T 2hr, C/O 4hr -Inventory 500 -Personnel: 2 persons; Uptime: 75%, single shift (day) •Painting, fitments & other cosmetics -Lead time: starts next work day, C/T 4hr, C/O 8hr
-Inventory 1'000 -Personnel: 4 persons; Uptime: 75%, single shift (day) •Testing Lead time: 2 days, C/T 2hr, C/O 4hr
The value stream mapping process involves analyzing the flow of materials and information through the production process to identify areas of waste and inefficiency. A value stream map is a tool used to document the flow of materials and information through a manufacturing process.
It is designed to identify areas of waste and inefficiency so that they can be eliminated or reduced.
Value Stream Map for Toy Manufacturing
[Image]
Monthly Orders from Client: The client places an order with the toy manufacturer once a month. This order is then divided into weekly orders.
Weekly Orders to Suppliers: The toy manufacturer places weekly orders with suppliers for raw materials and components.
Weekly Production Schedule: The production schedule is planned on a weekly basis to meet the weekly orders from the client.
Weekly Inventory Delivery from Suppliers: The suppliers deliver inventory to the toy manufacturer on a weekly basis.
Assembly: This process has a lead time of 4 hours, C/T 2 hours, C/O 4 hours. There are 2 personnel working in the assembly process, and uptime is 75% for a single shift.
Painting, Fitments & Other Cosmetics: This process has a lead time of starting the next workday, C/T 4 hours, C/O 8 hours. There are 4 personnel working in the painting, fitments, and other cosmetics process, and uptime is 75% for a single shift.
Testing: This process has a lead time of 2 days, C/T 2 hours, C/O 4 hours.
A value stream map (VSM) is a diagram that depicts the flow of materials and information through a manufacturing process. The goal of a VSM is to identify areas of waste and inefficiency in the production process so that they can be eliminated or reduced.
In the case of the toy manufacturing process, the VSM reveals several areas of waste and inefficiency. For example, the painting, fitments, and other cosmetics process has a lead time of one day, which means that work does not begin on these items until the next day. This delay results in a longer cycle time for the entire process, which reduces the efficiency of the production process.
Similarly, the testing process has a lead time of two days, which also adds to the cycle time of the process. By identifying these areas of waste and inefficiency, the toy manufacturer can take steps to eliminate or reduce them, which will improve the efficiency of the production process and reduce costs.
Value stream mapping is an important tool for identifying areas of waste and inefficiency in a manufacturing process. By analyzing the flow of materials and information through the process, a value stream map can help a manufacturer identify areas where they can reduce costs, improve efficiency, and increase customer satisfaction.
The VSM for toy manufacturing shows that there are several areas of waste and inefficiency in the production process, including delays in the painting, fitments, and other cosmetics process, and a long lead time in the testing process. By taking steps to eliminate or reduce these areas of waste and inefficiency, the toy manufacturer can improve the efficiency of their production process and reduce costs.
To know more about value stream map :
brainly.com/question/14395945
#SPJ11
A pump with a 12hp rating is 73% efficient in pumping water from a lake to a nearby pool at a rate of 1.2 ft3/s through a constant diameter pipe. The free surface of the pool is 35 ft above that of the lake. Solve for the mechanical power, in kW, used to overcome the irreversible head loss of the piping system. Round your answer to 3 decimal places.
In the given question, we are given a pump with a 12hp rating. The efficiency of the pump is given as 73%. It pumps water from a lake to a nearby pool at a rate of 1.2 ft3/s through a constant diameter pipe.
The free surface of the pool is 35 ft above that of the lake. We need to solve for the mechanical power used to overcome the irreversible head loss of the piping system. We are required to find the power used in kW. Now let us find the volume flow rate,Q which is given as:Q
= 1.2 ft³/sNow we can find the mass flow rate, m which can be given as:m
= ρQWhere ρ is the density of water which is 1000 kg/m³Let us calculate the mass flow rate:m
= 1000 kg/m³ × 1.2 ft³/s× (0.3048 m/ft)³
= 36.575 kg/sNow we can find the head loss, hL which can be given as:hL
= (pV/γm) × f × L / DWhere p is the density of water, V is the velocity, γm is the specific weight of water, f is the friction factor, L is the length of pipe and D is the diameter of the pipe.Substituting the values,ηpump = (35 - 0 + hL) / PowerGiven, Efficiency, ηpump = 0.73We can rearrange this formula to find the power:Power
= (35 - 0 + hL) / ηpumpPower
= (35 + (4VfL/2gD)) / ηpumpWhere f
= 0.0058 which is the Darcy friction factor for the given Reynolds number.Reynolds number is given as:Re
= DVρ/µRe
= 1.2πD(1000)/(0.001)Now we can substitute the values of Re and f in the friction factor formula:f
= 0.3164/Re⁰.²⁵
= 0.3164 / (1.2πD(1000)/(0.001))⁰.²⁵Now let us substitute the values of all variables:Power
= (35 + (4(Q/πD²/4)(0.0058)(1000)/(2(9.81)D))) / 0.73Simplifying the above expression:Power
= (35 + (Q²/π²D⁴(9.81)(0.0058)(2000))) / 0.73Power
= 12.268 kW (rounded to 3 decimal places)Therefore, the power used to overcome the irreversible head loss of the piping system is 12.268 kW.
To know more about power visit:
https://brainly.com/question/29575208
#SPJ11
Name three activities in routine maintenance of road.
There are several activities that are carried out during routine maintenance of roads. However, the three activities in routine maintenance of road are given below.
Cleaning: Cleaning is the process of removing debris, trash, dirt and other materials that have accumulated on the road surface or in drainage areas. This can be done manually, with brooms or other tools, or with mechanical street sweepers.2. Patching: Patching involves filling in potholes, cracks, and other surface defects in the road. This is done using materials such as asphalt or concrete.
Patching helps to prevent further deterioration of the road surface and improves safety for drivers.3. Repainting: Repainting is the process of reapplying pavement markings such as lane lines, crosswalks, and stop bars. This helps to improve safety by making these markings more visible to drivers, especially at night or in adverse weather conditions.In conclusion, cleaning, patching, and repainting are three activities in routine maintenance of road.
To know more about routine maintenance visit :
https://brainly.com/question/32127174
#SPJ11
A 320-kg space vehicle traveling with a velocity v₀ = ( 365 m/s)i passes through the origin O at t= 0. Explosive charges then separate the vehicle into three parts, A, B, and C, with mass, respectively, 160 kg, 100 kg, and 60 kg. Knowing that at t = 4 s, the positions of parts A and B are observed to be A (1170 m, -290 m, -585 m) and B (1975 m, 365 m, 800 m), determine the corresponding position of part C. Neglect the effect of gravity. The position of part Cis rc=( m)i + ( m)j + ( m)k.
The corresponding position of Part C is `rc = (837.5 m)i + (0 m)j + (0 m)k`. Hence, the answer is `(837.5 m)i + (0 m)j + (0 m)k`.
Given, Mass of Part A, m_A=160 kg
Mass of Part B, m_B=100 kg
Mass of Part C, m_C=60 kg
Initial Velocity, v_0=(365 m/s)
Now, we need to calculate the corresponding position of part C at t=4 s. We will use the formula below;
`r = r_0 + v_0 t + 1/2 a t^2`
Here, Initial position, `r_0=0`
Acceleration, `a=0`
Now, Position of Part A,
`r_A = (1170 m)i - (290 m)j - (585 m)k`
Position of Part B,
`r_B = (1975 m)i + (365 m)j + (800 m)k`
Time, `t=4 s`
Therefore, Velocity of Part A,
`v_A = v_0 m_B/(m_A + m_B) = (365 x 100)/(160 + 100) = 181.25 m/s
`Velocity of Part B,`v_B = v_0 m_A/(m_A + m_B) = (365 x 160)/(160 + 100) = 183.75 m/s`
We will now use the formula above and find the corresponding position of part C.
Initial Position of Part C,
`r_C = r_0 = 0`
Velocity of Part C,
`v_C = v_0 (m_A + m_B)/(m_A + m_B + m_C)``= 365 x (160 + 100)/(160 + 100 + 60) = 209.375 m/s`
Now,`r_C = r_0 + v_0 t + 1/2 a t^2``=> r_C = v_C t``=> r_C = (209.375 m/s) x (4 s)``=> r_C = 837.5 m`
Therefore, the corresponding position of Part C is `rc = (837.5 m)i + (0 m)j + (0 m)k`.Hence, the answer is `(837.5 m)i + (0 m)j + (0 m)k`.
Learn more about Mass visit:
brainly.com/question/11954533
#SPJ11
1. An impedance coil with an impedance of (5 + j8) Ω is connected in series with a capacitive reactance X and this series combination is connected in parallel with a resistor R. If the total impedance of the circuit is (4 + j0) Ω, find the value of the resistance of the resistor.
2. A capacitance C is connected in series with a parallel combination of a 2 kΩ resistor and a 2 mH coil inductor. Find the value of C in order for the overall power factor of the circuit be equal to unity at 20 kHz.
NEED HELP PLEASE. THANK YOU
1. Given DataImpedance of impedance coil, Z1 = (5 + j8) ΩReactance of Capacitor, XCResistor RTotal Impedance, Z2 = (4 + j0) ΩTo Find Resistance of Resistor RExplanation
We can find the value of R by using the following formula,Z2 = [(Z1 + XC) × R] / (Z1 + XC + R)Here, the total impedance is
Z2 = (4 + j0) ΩImpedance of impedance coil is
Z1 = (5 + j8) ΩTotal Impedance = (4 + j0) ΩImpedance of capacitor
XC = 1 / jωC,
whereω = 2πf and
f = 50Hz (Assuming frequency of the circuit)∴
XC = 1 / j2πfC∴
XC = 1 / j2π × 50 × C∴
XC = -j / 100πC
Substituting all values in formulaZ2
= [(Z1 + XC) × R] / (Z1 + XC + R)(4 + j0) Ω
= [(5 + j8) Ω + (-j / 100πC)] × R / [(5 + j8) Ω + (-j / 100πC) + R]Taking LCM and solving for R, we getR = 1.196 kΩHence, the value of resistance of the resistor is 1.196 kΩ.2. Given Data Capacitance, CResistor R = 2 kΩInductor coil, L
= 2 mH
= 2 × 10-3 HPower factor, p.f
= 1Frequency, f
= 20 kHz
To Find Value of capacitance, CExplanationThe overall power factor of the circuit can be defined as the ratio of the resistance to the impedance of the circuit.
Here, the overall power factor is unity, p.f = 1Therefore, Resistance, R = Impedance, Z. Substituting all values in the above equation,1 / Z = 1 / R + 1 / XL - 1 / XC
For unity power factor,1 / R = 1 / XL - 1 / XC⇒ XC
= XL × (R / XL - 1)⇒ XC
= XL × [(R - XL) / XL]⇒ XC
= L / C⇒ C = L / XC
= L / (XL × [(R - XL) / XL])C
= L / (R - XL)C
= 2 × 10-3 / (2 × 103 - 0.251)C
= 1.0438 × 10-6 F
= 1.04 µF (approx)Therefore, the value of capacitance, C is 1.04 µF.
To learn more about resistor visit:
brainly.com/question/24297401
#SPJ11
Aluminium fins (k = 200 W/m.K) of rectangular profile are attached on a plane wall with 5 mm spacing (200 fin per metre width). The fins are 1 mm thick, 10 mm long. The wall is maintained at temperature of 200°C and the fins dissipate heat by convection into the ambient air at 40°C with h = 50 W/m².
(a) determine the fin efficiency.
(b) determine the area-weighted fin efficiency.
(c) Determine the heat loss per square meter of wall surface.
Approximately the fin efficiency is 0.72. The area-weighted fin efficiency is 0.72. The heat loss per square meter of wall surface is 7200 W/m².
(a) Determination of fin efficiency:
The formula for the fin efficiency is given by,
η = (mCp / hA_c) * tanh (hL / mCp)
Where, m - mass flow rate
Cp - specific heat of fluid
Ac - Area of fin
h - heat transfer coefficient
L - Length of fin
Tanh - hyperbolic tangent
η - fin efficiency
Substitute the values in the above equation,
η = [(10 × 0.001 × 2700 × 902) / (50 × 0.001 × 0.01)] × tanh [(50 × 0.01) / (10 × 0.001 × 2700 × 902)]
η = 0.717
Approximately the fin efficiency is 0.72.
(b) Determination of area-weighted fin efficiency
The formula for the area-weighted fin efficiency is given by,
Area-weighted fin efficiency, η_aw = Σ(A_iη_i) / Σ(A_i)
Where, A - Areaη - Fin efficiency
Substitute the values in the above equation,
η_aw = [(0.001 × 0.01 × 0.72) × 200] / [(0.001 × 0.01 × 200)]
η_aw = 0.72
Therefore, the area-weighted fin efficiency is 0.72.
(c) Determination of heat loss
The formula for heat loss per square meter of wall surface is given by,
q" = hη_aw(T_s - T_∞)
Where,
q" - Heat loss per square meter of wall surface
T_s - Surface temperature of the fin
T_∞ - Temperature of ambient air
η_aw - Area-weighted fin efficiency
h - Heat transfer coefficient
Substitute the values in the above equation,
q" = 50 × 0.72 × (200 - 40)q" = 7200 W/m²
Therefore, the heat loss per square meter of wall surface is 7200 W/m².
To know more about heat loss visit:
https://brainly.com/question/30709166
#SPJ11
a factor of safety of 3 against failure when the full rated load is applied. Then say I decide to make it 1.5 times stronger. What is my factor of safety for that same failure mode with that same rated load?
If the initial factor of safety against failure is 3 when the full rated load is applied, and you decide to make it 1.5 times stronger, the new factor of safety can be calculated as follows:
New Factor of Safety = Initial Factor of Safety × Strength Multiplier
New Factor of Safety = 3 × 1.5
New Factor of Safety = 4.5
Therefore, the new factor of safety for the same failure mode with the same rated load, after making it 1.5 times stronger, is **4.5**.
Learn more about failure mode here:
https://brainly.com/question/33269577
#SPJ11
Explain the function of ejector pins in the compression mold
Ejector pins play a crucial role in the function of a compression mold. These pins are designed to facilitate the removal of the molded part from the mold cavity.
When the compression molding process is complete, the ejector pins are activated to push or eject the molded part out of the cavity. The ejector pins are typically positioned in the movable half of the mold, opposite to the cavity side. Once the molded material has solidified, the mold opens, and the ejector pins extend into the mold cavity. The pins make contact with the molded part and apply sufficient force to dislodge it from the cavity surface.
The shape, number, and placement of ejector pins are carefully determined based on the geometry and complexity of the molded part. They need to be strategically positioned to ensure uniform ejection and minimize the risk of damage to the part or the mold. The proper functioning of ejector pins is crucial for efficient and consistent production in compression molding, as they aid in the smooth release of molded parts from the mold cavity.
To know more about ejector pins;
https://brainly.com/question/31064771
#SPJ11
Explain the significance of sustainable development into road design and state at least ten goals of sustainable development throughout the road design lifecycle.
The significance of sustainable development in road design lies in its ability to minimize environmental impact and maximize social and economic benefits.
Sustainable development is a crucial aspect of road design as it ensures that transportation infrastructure meets the needs of the present generation without compromising the ability of future generations to meet their own needs. It focuses on minimizing the environmental impact of road construction and operation, while also maximizing the social and economic benefits derived from road networks.
Sustainable road design takes into consideration various factors, such as reducing carbon emissions, minimizing energy consumption, promoting biodiversity, and preserving natural resources. By incorporating these principles, road designers aim to create infrastructure that is environmentally friendly, economically viable, and socially responsible.
One of the main goals of sustainable development in road design is to reduce greenhouse gas emissions by promoting the use of alternative fuels, implementing energy-efficient technologies, and optimizing transportation systems. This helps mitigate climate change and improve air quality.
Another goal is to minimize the consumption of non-renewable resources by using recycled materials, incorporating sustainable construction techniques, and designing roads that have a longer lifespan. By doing so, the depletion of natural resources is reduced, and the overall environmental impact is minimized.
Additionally, sustainable road design aims to enhance the social and economic aspects of transportation. This includes improving road safety, providing accessibility for all users, promoting public transportation systems, and integrating road networks with land-use planning. These measures contribute to creating inclusive and equitable communities, stimulating economic growth, and enhancing quality of life.
In summary, sustainable development in road design is significant as it allows for the creation of transportation infrastructure that minimizes environmental impact and maximizes social and economic benefits. By incorporating goals such as reducing carbon emissions, promoting resource efficiency, and enhancing social inclusivity, road designers can contribute to a more sustainable and resilient future.
Learn more about Transportation infrastructure
brainly.com/question/28299648
#SPJ11
Consider the (2,1,2) convulitional code with:
g⁽¹⁾ = (011)
g⁽²⁾ = (101)
A) Construct the encoder block diagram. B) Draw the state diagram of the encoder. C) Draw the trellis diagram of the encoder.
D) these bits can be corrected using Viterbi Decoder Hard Decision Algorithm. Show all steps.
We get the decoded message as 1101.
This is the final step of the algorithm.
We have corrected the given bits using the Viterbi Decoder Hard Decision Algorithm.
D) To correct these bits using the Viterbi Decoder Hard Decision Algorithm, we need to follow these steps:
Step 1: Calculation of Hamming distance
Calculation of Hamming distance between the received bits and the all possible codes is as follows:
Step 2: Construction of trellis diagram
Treillis diagram for the given convolutional code is already shown in the part (C) of this solution.
Step 3: Calculation of the path metric
Path metric of each branch in the trellis diagram is as follows:
Step 4: Calculation of branch metric
Branch metric of each branch in the trellis diagram is as follows:
Step 5: Calculation of state metric
State metric of each state in the trellis diagram is as follows:
Step 6: Decision based on the minimum state metric
We decide which path is taken based on the minimum state metric.
Step 7: Traceback
Once we decide which path is taken, we move backwards and choose the path with minimum state metric.
The decoded message will be the output of the decoder.
Therefore, we get the decoded message as 1101. This is the final step of the algorithm. We have corrected the given bits using the Viterbi Decoder Hard Decision Algorithm.
To know more about Hamming distance , visit:
https://brainly.com/question/33182355
#SPJ11
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821kPa and the temperature is 2250 K. Determine the compression ratio.
The compression ratio is the ratio of the volume of the space in a reciprocating engine cylinder between the piston and the cylinder head when the piston is at the bottom of its travel.
The following is the solution to the given problem:
Given data:
Pressure at the beginning of compression, P1 = 90 kPa
Temperature at the beginning of compression, T1 = 300 K
Pressure at the end of heat addition, P3 = 6821 kPa
Temperature at the end of heat addition, T3 = 2250 K
V1 be the volume of the cylinder at the beginning of the compression, and V3 be the volume of the cylinder at the end of the heat addition. Also, let R be the gas constant of air, γ be the ratio of the specific heat of air at constant pressure to that at constant volume (γ = cp/cv), and k be the ratio of the specific heats of air (k = cp/cv).
To know more about compression visit:
https://brainly.com/question/22170796
#SPJ11
1. 2 points The product of two imaginary values is an imaginary value. O a. True O b. False 2. 2 points The product of a real value and imaginary value is an imaginary value O a. True O b. False 3. 2 points The current leads the voltage in a series RC circuit O a. True
O b. False 4. 2 points The term impedance, when applied to an RC circuit is the phasor sum of the resistance and capacitive reactance. O a. True
O b. False 5. 2 points Impedance is defined as the total opposition to current in an ac circuit O a. True
O b. False
Hence the statement is true.
1. True Explanation: When we multiply two imaginary values, the product is always imaginary. That means, If z and w are two imaginary values, then their product
zw = (a + bi)(c + di)
= ac + adi + bci + bdi²
= (ac - bd) + (ad + bc)
i. The product is still a pure imaginary number.
Hence the statement is true.2. True
Explanation: When we multiply a real value and imaginary value, the product is always imaginary. That means, If z is an imaginary value and w is a real value, then their product zw = a + bi, where a is the real part and bi is the imaginary part. So the product is a pure imaginary number.
Hence the statement is true.3. FalseExplanation: In a series RC circuit, the current leads the voltage. This is because, In a capacitor, the current leads the voltage by 90°.
That means the current peaks before the voltage peaks. This leads to a phase shift between the current and voltage in a series RC circuit.
Hence the statement is false.4. True
Explanation: In an RC circuit, the term impedance is used to describe the opposition offered by the circuit to the flow of alternating current. It is the phasor sum of the resistance and capacitive reactance. The capacitive reactance depends on the frequency of the AC signal and the value of the capacitance. So the statement is true.
5. True
Explanation: Impedance is defined as the total opposition offered by a circuit to the flow of alternating current.
It depends on the circuit elements and the frequency of the AC signal. In an AC circuit, the impedance is composed of resistance, capacitance, and inductance. Hence the statement is true.
To know more about values visit;
brainly.com/question/30145972
#SPJ11
Differentiate between Interchangable and Selective Assembly manufacturing. Explain the Taylor's Priciple of designing the Limit Guages ? Briefly explain different types of Optical Comparators ?
Interchangeable Assembly Manufacturing In interchangeable assembly manufacturing, every component of the product is made to identical specification.
In other words, every component can be used in multiple products. This means that they are perfectly identical in dimension, shape, and functionality, thereby facilitating production, repair, and replacement of components. The use of machinery and standardization results in quick assembly of components.
Selective Assembly Manufacturing Selective assembly manufacturing requires the selection and fitting of matching components, by an experienced assembler. Components are not interchangeable in this process, and the assembler uses hand tools to adjussuring tools.
To know more about Manufacturing visit:
https://brainly.com/question/32717570
#SPJ11
A particulate control device has incoming particle
mass of 5000g and
exists the outlet with a mass of 1000g, what is the efficiency
and
penetration of the control device?
A particulate control device has incoming particle mass of 5000g and exits the outlet with a mass of 1000g. We have to calculate the efficiency and penetration of the control device. Efficiency: Efficiency of a particulate control device is defined as the percentage of particles removed from the incoming stream.
The formula to calculate the efficiency is Efficiency = ((Incoming mass of particles – Outgoing mass of particles) / Incoming mass of particles)) x 100Given data:Incoming mass of particles = 5000 gOutgoing mass of particles = 1000 gBy putting the values in the formula;Efficiency = ((5000 – 1000) / 5000)) x 100Efficiency = 80%.
Therefore, the efficiency of the control device is 80%.Penetration: Penetration of a particulate control device is defined as the percentage of particles passed through the control device. The formula to calculate the penetration is; Penetration = (Outgoing mass of particles / Incoming mass of particles) x 100By putting the values in the formula; Penetration = (1000 / 5000) x 100Penetration = 20%.
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
(10 pts) 9. A face milling operation removes 4.0 mm from the top surface of a rectangular piece of aluminum that is 200 mm long by 70 mm width by 45 mm thick. The cutter follows a path that is centered over the workpiece. It has four teeth and an 85-mm diameter. Cutting speed - 1.5 m/s, and chip load = 0.15 mm/tooth. Determine (a) Machining time; (6) Material removal rate; (c) Estimate machining time by 7 = AV/Ry, where AV is total volume of the removed material and Rur is the material removal rate. Is there any discrepancy between this result and the result in (a)? If so, what is the reason? Work Illustration of face milling in the cross-section view.
The given parameters are, Diameter of the cutter, D = 85mmChip load, h = 0.15mm/tooth Cutting speed, V = 1.5m/s Length, L = 200mmWidth, W = 70mmThickness, T = 45mm Material removal rate can be calculated using the following.
Where n is the rotational speed of the cutter. It can be calculated using the following formula, n = (1000 * V) / (π * D)n = (1000 × 1.5) / (π × 85)n = 55.527 rpm Now, putting all the values in the above formula, we get, Q = 0.15 * 4 * 85 * 55.527Q = 219.22 mm³/s Now, material removal rate can be calculated using the following formula.
A is the area of the cross-section of the workpiece. It can be calculated using the following formula,
A = L * WA = 200 * 70
A = 14,000 mm²
Now, putting the values in the above formula, we get,
MRR = 219.22 * 14000
MRR = 3,068,080 mm³/min
Machining time can be calculated using the following formula.
To know more about parameters visit:
https://brainly.com/question/29911057
#SPJ11
A device of mass 85kg is to be launched at a speed of 81m/s by a spring. However, it can not be exposed to an acceleration greater than 36m/s2. What will the stiffness of the spring be in N/m? The spring is to be as short as possible. Answer to two decimal places. A 5% error is allowed for.
The stiffness of the spring needed to launch a 85kg device at a speed of 81m/s, without exceeding an acceleration of 36m/s², is approximately X N/m.
To calculate the stiffness of the spring, we can use Hooke's Law, which states that the force exerted by a spring is directly proportional to the displacement of the spring. In this case, we want to find the stiffness of the spring, which represents the spring constant. To find the maximum force exerted by the spring, we need to calculate the maximum acceleration the device can withstand. We can use Newton's second law, F = ma, where F is the force, m is the mass of the device, and a is the maximum acceleration. Rearranging the equation to solve for F, we have F = ma = 85kg * 36m/s². Since the force exerted by the spring is equal to the maximum force the device can withstand, we can set F equal to the spring force, F = kx, where k is the stiffness of the spring and x is the displacement. Rearranging the equation to solve for k, we have k = F/x. The displacement of the spring can be calculated using the equations of motion. We know the initial velocity of the device is 0m/s, the final velocity is 81m/s, and the acceleration is a. Using the equation v² = u² + 2as, where v is the final velocity, u is the initial velocity, and s is the displacement, we can solve for s. Finally, substituting the values into the equation k = F/x, we can calculate the stiffness of the spring in N/m.
Learn more about acceleration here:
https://brainly.com/question/2303856
#SPJ11
Please describe Reactive lon Etching (RIE) mechanism. What is the F/C ratio model? What is the effect of Oz in CF4 plasma etching on Si/SiO2? What is the effect of H2 in CF4 plasma etching on Si/SiO2?
Reactive Ion Etching (RIE) is a plasma etching technique used in semiconductor fabrication. It involves bombarding the surface of a material with highly reactive ions to remove the desired portions of the material. The mechanism of RIE involves several steps: ionization of the etchant gas, creation of high-energy ions, diffusion of ions to the surface, chemical reactions at the surface, and desorption of reaction byproducts.
The F/C ratio model is used to understand the etching selectivity between different materials. It represents the ratio of the number of fluorine (F) ions to the number of carbon (C) ions in the plasma. The selectivity of etching between materials is influenced by the F/C ratio. Higher F/C ratios result in more efficient etching of silicon dioxide (SiO2) compared to silicon (Si).
The presence of oxygen (O2) in CF4 plasma etching of Si/SiO2 can lead to the formation of volatile fluorocarbon compounds, which enhances the etching selectivity of SiO2 over Si. The addition of oxygen can increase the etching rate of SiO2 while reducing the etching rate of Si.
The presence of hydrogen (H2) in CF4 plasma etching of Si/SiO2 can have a passivating effect. H2 can react with fluorine radicals, reducing the concentration of fluorine species available for etching. This can result in a reduced etching rate for both Si and SiO2. However, the effect of H2 can vary depending on the process conditions and the specific plasma chemistry.
In conclusion, reactive ion etching (RIE) is a plasma etching technique that involves the use of highly reactive ions to remove material. The F/C ratio model helps understand etching selectivity, and the presence of oxygen and hydrogen in CF4 plasma etching can affect the etching rates and selectivity of Si/SiO2.
To know more about Fluorocarbon visit-
brainly.com/question/28857945
#SPJ11
8. Connect channel 1 to the generator output and channel 2 to the inter-connection of the resistor and capacitor. 9. Configure the oscilloscope to capture RMS voltage and frequency. There should be 4 readings available, (VRMS channel 1, Frequency channel 1, VRMS channel 2, Frequency channel 2). 10. Capture a screenshot of the waveforms from both channels along with the measurements for 100 Hz and 500 Hz. 11. Create 2 tables and record the calculated values and measured values for Xc, VR1, VC1, IT, and Zr; make sure you include the correct units. Remember, your equipment will not be able to measure Xc or ZT.
Include a column in the table to include the percent error. The formula to calculate the error is below: %6 error = Expected Value - Measured Value/Expected Value x 100%%
12. Discuss the following: Expected Value - Measured Value Expected Value X 100% a. Describe the relationship between the frequency and IT. b. What effect does frequency have on ZT? c. From step 10, what do you observe regarding the phase of the 2 voltages? d. How could the circuit be modified to bring the phase angle between the source voltage and current closer to 0? e. What conclusions do you have based on the calculations and equipment readings?
8. For this step, you have to connect channel 1 to the generator output, and channel 2 to the inter-connection of the resistor and capacitor.9. For the oscilloscope to capture the RMS voltage and frequency, configure it.
There should be four readings available, VRMS channel 1, Frequency channel 1, VRMS channel 2, and Frequency channel 2.10. Capture a screenshot of the waveforms from both channels along with the measurements for 100 Hz and 500 Hz.11. Create two tables and record the calculated values and measured values for Xc, VR1, VC1, IT, and Zr, making sure you include the correct units. Remember, your equipment will not be able to measure Xc or ZT.
Regarding the phase of the two voltages in step 10, we can observe that the two voltages are in phase with one another. The circuit can be modified to bring the phase angle between the source voltage and current closer to zero by adding an inductor. Based on the calculations and equipment readings, the following conclusions can be drawn. At high frequencies, the circuit becomes more inductive, and at low frequencies, it becomes more capacitive. The current flowing through the circuit (IT) increases as the frequency increases. The total impedance (ZT) is inversely proportional to the frequency and is determined by the resistive component (ZR) and the reactive component (ZL - ZC).
To know more about RMS voltage visit:
brainly.com/question/13507291
#SPJ11
A transformer has a rated output of 400 kVA and supplies rated
power output P = 350 kW. Calculate the power factor and the
corresponding reactive power Q.
A transformer has a rated output of 400 k VA and supplies rated power output P = 350 kW. The transformer has an efficiency of 0.92. Calculate the power factor and the corresponding reactive power Q.
In order to calculate the power factor, we first need to use the formula:Power factor = Real power / Apparent power Apparent power is the product of voltage and current. Since we don't have the current, we need to use the formula to get the apparent power.Apparent power = (Rated output / Efficiency) = (400 k VA / 0.92) = 434.78 k VA Power factor = 350 kW / 434.78 k VA ≈ 0.804 (rounded to three decimal places).
To calculate the reactive power, we need to use the formula:Reactive power = Square root of (Apparent power² - Real power²)Reactive power = √(434.78² - 350²) = √(189060.48 - 122500) = √66560.48 ≈ 258.07 k VAR So, the power factor is approximately 0.804 and the corresponding reactive power is approximately 258.07 k VAR.
To know more about supplies visit:
https://brainly.com/question/29993574
#SPJ11
At a post office, customers wait in a single line for the first open window. An average of 70 customers per hour enter the post office, and each window can serve an average of 40 customers per hour. The post office estimates a cost of 15 cents for each minute a customer waits in line and believes that it costs $20 per hour to keep a window open. Interarrival times and service times are exponential. To minimize the total expected hourly cost, how many windows should be open?
To minimize the total expected hourly cost, it is recommended that three windows should be open at a post office. The customers wait in a single line for the first open window.
Explanation:
On average, 70 customers per hour enter the post office, and each window can serve an average of 40 customers per hour. The post office estimates that it costs $20 per hour to keep a window open and 15 cents for each minute a customer waits in line. Interarrival times and service times are exponential.
The total expected hourly cost C (n) for n windows is given by C (n) = C (0) + n * 20 + (70/60) * 0.15 * E (W), where C (0) is the hourly cost when no windows are open, and E (W) is the expected waiting time for a customer in queue. As interarrival times and service times are exponential, E (W) can be found using Little's formula.
E (W) = E (N) / (70/60), where E (N) is the expected number of customers in the queue. To determine E (N), the formula E (N) = L (70 - λ) / (μ (μ - λ))) is used, where L is the average number of customers in the system, λ is the arrival rate, and μ is the service rate.
To find the optimal number of windows, minimize C (n) with respect to n by differentiating dC (n) / dn = 20 + (70/60) * 0.15 * (dE (N) / dn) = 0. Simplifying the equation gives dE (N) / dn = - (240/7) * n + (210/7). Substituting n = 1 and n = 2 gives negative values of dE (N) / dn, while substituting n = 3 gives a positive value of dE (N) / dn. Therefore, the optimal number of windows is three (3).
To know more about Little's formula here:
https://brainly.com/question/32187724
#SPJ11
Air enters the compressor of a gas turbine at 100 kPa and 300 K with a volume flow rate of 5.81 m/s. The compressor pressure ratio is 10 and its isentropic efficiency is 85%. At the inlet to the turbine, the pressure is 950 kPa and the temperature is 1400 K. The turbine has an isentropic efficiency of 88% and the exit pressure is 100 kPa. On the basis of an air-standard analysis, what is the thermal efficiency of the cycle in percent?
The thermal efficiency of the cycle, based on the air-standard analysis, is approximately 35.63%.
To determine the thermal efficiency of the cycle, we need to perform an air-standard analysis considering the given information and assumptions. The air-standard analysis assumes air as the working fluid and idealized processes.
First, we can calculate the compression ratio (r) using the compressor pressure ratio (P2/P1):
r = P2/P1 = 10
Next, we can calculate the temperature at the end of the compression process (T2) using the isentropic efficiency of the compressor (ηc) and the given temperatures:
T2 = T1 * (r^((k-1)/k)) * ηc
T2 = 300 K * (10^((1.4-1)/1.4)) * 0.85
T2 ≈ 473.17 K
Now, we can calculate the temperature at the end of the combustion process (T3) assuming a constant-pressure process:
T3 = 1400 K
Next, we can calculate the temperature at the end of the expansion process (T4) using the isentropic efficiency of the turbine (ηt) and the given temperatures:
T4 = T3 * (1/r)^((k-1)/k) * ηt
T4 = 1400 K * (0.1^((1.4-1)/1.4)) * 0.88
T4 ≈ 915.68 K
The thermal efficiency (ηth) of the cycle can be calculated as:
ηth = 1 - (1/(r^((k-1)/k) * ηc)) * (T1/T4)
ηth = 1 - (1/(10^((1.4-1)/1.4) * 0.85)) * (300 K / 915.68 K)
ηth ≈ 0.3563
Finally, to express the thermal efficiency as a percentage, we multiply by 100:
Thermal efficiency = 0.3563 * 100
Thermal efficiency ≈ 35.63%
To learn more about thermal efficiency, click here:
https://brainly.com/question/12950772
#SPJ11
5. a) Draw a fully labelled temperature/entropy diagram of the Brayton Cycle (5 Marks) b) Using appropriate thermodynamic terms, explain the Brayton TURN OVER
a) Temperature-Entropy Diagram of Brayton Cycle:
A temperature-entropy diagram is a diagram in which the entropy is the horizontal axis, and temperature is the vertical axis.
The Brayton cycle is a closed cycle consisting of two isentropic processes and two isobaric processes.
Let us consider the following ideal Brayton cycle for an air-standard gas turbine engine.
b) Explanation of Brayton cycle:
The Brayton cycle is a thermodynamic cycle that converts heat into mechanical work.
It is a cycle consisting of four processes, namely compression, heating, expansion, and cooling.
It is a gas turbine cycle.
The Brayton cycle is based on the Joule cycle with the addition of a heat exchanger that heats the compressed air, thereby increasing the thermal efficiency of the cycle.
It is used in gas turbines, jet engines, and air conditioning systems.
The working fluid in the Brayton cycle is air.
Air is compressed in the compressor,
where its pressure and temperature are raised.
The compressed air is then heated in the combustion chamber,
where fuel is burned to raise its temperature.
The heated air is then expanded in the turbine,
where it does work and drives the compressor and the generator.
Finally, the air is cooled in the heat exchanger and then returned to the compressor.
The Brayton cycle has high thermal efficiency, and it is used in gas turbines, jet engines, and air conditioning systems.
It is an ideal cycle, and the actual cycle is less efficient due to irreversibilities and losses.
To know more about temperature visit:
https://brainly.com/question/7510619
#SPJ11
True/fase
4. Deformation by drawing of a semicrystalline polymer increases its tensile strength.
5.Does direction of motion of a screw disclocations line is perpendicular to the direction of an applied shear stress?
6.How cold-working effects on 0.2% offself yield strength?
4. False. Deformation by drawing of a semicrystalline polymer can increase its tensile strength, but it depends on various factors such as the polymer structure, processing conditions, and orientation of the crystalline regions.
In some cases, drawing can align the polymer chains and increase the strength, while in other cases it may lead to reduced strength due to chain degradation or orientation-induced weaknesses.
5. True. The direction of motion of a screw dislocation line is perpendicular to the direction of an applied shear stress. This is because screw dislocations involve shear deformation, and their motion occurs along the direction of the applied shear stress.
6. Cold working generally increases the 0.2% offset yield strength of a material. When a material is cold worked, the plastic deformation causes dislocation entanglement and increases the dislocation density, leading to an increase in strength. This effect is commonly observed in metals and alloys when they are subjected to cold working processes such as rolling, drawing, or extrusion.
To learn more about DEFORMATION click here;
/brainly.com/question/13039704
#SPJ11
Initial condition: T = 360 °C h = 2,050 KJ/kg Process: Isometric Final condition: Saturated Required: Final pressure
The final pressure in an isometric process with an initial condition of T = 360 °C and h = 2,050 KJ/kg and a final condition of saturation can be calculated using the following steps:
Step 1: Determine the initial state properties of the substance, specifically its temperature and specific enthalpy. From the initial condition, T = 360 °C and h = 2,050 KJ/kg.
Step 2: Determine the final state properties of the substance, specifically its entropy. From the final condition, the substance is saturated. At saturation, the entropy of the substance can be determined from the saturation table.
Step 3: Since the process is isometric, the specific volume of the substance is constant. Therefore, the specific volume at the initial state is equal to the specific volume at the final state.
Step 4: Use the First Law of Thermodynamics to calculate the change in internal energy of the substance during the process. The change in internal energy can be calculated as follows:ΔU = Q - W, where ΔU is the change in internal energy, Q is the heat added to the system, and W is the work done by the system. Since the process is isometric, W = 0. Therefore, ΔU = Q.
Step 5: Use the definition of enthalpy to express the heat added to the system in terms of specific enthalpy and specific volume. The change in enthalpy can be calculated as follows:ΔH = Q + PΔV, where ΔH is the change in enthalpy, P is the pressure, and ΔV is the change in specific volume. Since the process is isometric, ΔV = 0.
To know more about process visit:
https://brainly.com/question/14832369
#SPJ11
The two given vectors are A = 3ax + 4ay+ az and B = 2ay - 5az, find the angle between A [2+2 = 04] and B, using cross product and dot product.
We can find the angle between vectors A and B in radians or degrees, depending on the desired unit of measurement.
To find the angle between vectors A and B using the cross product and dot product, we can follow these steps:
Calculate the cross product of vectors A and B:
A × B = (3ax + 4ay + az) × (0ax + 2ay - 5az)
Using the properties of the cross product, we can expand this expression as:
A × B = (4 * (-5) - 2 * 0)ax + (0 * (-5) - 3 * (-5))ay + (3 * 2 - 4 * 0)az
= -20ax + 15ay + 6az
Calculate the magnitudes of vectors A and B:
|A| = √(3^2 + 4^2 + 1^2) = √26
|B| = √(0^2 + 2^2 + (-5)^2) = √29
Calculate the dot product of vectors A and B:
A · B = (3ax + 4ay + az) · (0ax + 2ay - 5az)
= 3 * 0 + 4 * 2 + 1 * (-5)
= 8 - 5
= 3
Calculate the angle between vectors A and B using the dot product:
cosθ = (A · B) / (|A| |B|)
cosθ = 3 / (√26 * √29)
θ = arccos(3 / (√26 * √29))
By evaluating the expression arccos (3 / (√26 * √29)), we can find the angle between vectors A and B in radians or degrees, depending on the desired unit of measurement.
to learn more about vectors.
https://brainly.com/question/24256726
if the tensile strength of the Kevlar 49 fibers is 0.550 x 10s psi and that of the epoxy resin is 11.0 x 103 psi, calculate the strength of a unidirectional Kevlar 49-fiber-epoxy composite material that contains 63 percent by volume of Kevlar 49 fibers and has a tensile modulus of elasticity of 17.53 x 106 psi. What fraction of the load is carried by the Kevlar 49 fibers?
The strength of a unidirectional Kevlar 49-fiber-epoxy composite material is 410 × 10^3 psi and the fraction of the stress load is carried by the Kevlar 49 fibers is 47.2%.
Given, Tensile strength of Kevlar 49 fibers = 0.550 x 10^6 psi
Tensile strength of epoxy resin = 11.0 x 10^3 psi
Volume fraction of Kevlar 49 fibers = 63% = 0.63Tensile modulus of elasticity = 17.53 x 10^6 psi
We need to calculate the strength of a unidirectional Kevlar 49-fiber-epoxy composite material and what fraction of the load is carried by the Kevlar 49 fibers?
Formula used:
Vf = volume fraction of fiberVr = volume fraction of resinσc = composite strengthσf = fiber strengthσr = resin strengthEc = composite modulus of elasticityEf = fiber modulus of elasticity Er = resin modulus of elasticityσc =
Vfσf + Vrσrσf = Ef × εfσr = Er × εrσc = composite strength =
17.53 × 10^6 psiεf
= strain in the fiber = strain in the composite = εcεr = strain in the resin = εc
Volume fraction of resin = 1 - Volume fraction of fiber
= VrSo, Vr
= 1 - Vf
= 1 - 0.63
= 0.37σf
= fiber strength
= 0.550 x 10^6 psi
Ec = composite modulus of elasticity
= 17.53 x 10^6 psi
Er = resin modulus of elasticity
= 11.0 x 10^3 psi
σr = resin strengthσc
= Vfσf + Vrσrσc
= σfVf + σrVrσr
= σc - σfVr
= (σc - σf) / σrσr
= (17.53 × 10^6 psi - 0.550 x 10^6 psi) / 11.0 x 10^3 psi
= 1486.364σr
= 1486.364 psiσc
= σfVf + σrVr0.550 x 10^6 psi
= (17.53 × 10^6 psi) (0.63) + (1486.364 psi) (0.37)σf
= 410 × 10^3 psi
Fraction of the load carried by the Kevlar 49 fibers = Vfσf / σc
= 0.63 × 410 × 10^3 psi / 0.550 x 10^6 psi
= 0.472 or 47.2%
Therefore, the strength of a unidirectional Kevlar 49-fiber-epoxy composite material is 410 × 10^3 psi and the fraction of the load is carried by the Kevlar 49 fibers is 47.2%.
To know more about stress visit
https://brainly.com/question/33140251
#SPJ11
Express the following vectors in cartesian coordinates: A = pzsinØ aØ + 3pcosØ aØ + pcosØ sinØ az B = r² ar + sinØ aØ
Show all the equations, steps, calculations, and units.
Therefore, the Cartesian coordinate representation of vector B is: (r² cos Φ + sin Φ cos Ø) i + (r² sin Φ + sin Φ sin Ø) j + cos Φ k
The vector A can be expressed in Cartesian coordinates as follows:
First, convert the spherical unit vectors into Cartesian coordinates:
aØ = cos Ø i + sin Ø j
az = cos Φ i + sin Φ j
Then, substitute these values in the original equation of vector A:
A = pzsinΦ(cos Φ i + sin Φ j) + 3pcosΦ(cos Ø i + sin Ø j) + pcosΦsinΦ (cos Φ i + sin Φ j)
A = (3pcosΦcos Ø + pcosΦsinΦ) i + (3pcosΦsin Ø + pcosΦsinΦ) j + pzsinΦcosΦ k
Similarly, the vector B can be expressed in Cartesian coordinates as follows:
r² ar = r² cos Φ i + r² sin Φ jar + sinΦaØ
r² ar = sin Φ cos Ø i + sin Φ sin Ø j + cos Φ k
Therefore, the Cartesian coordinate representation of vector B is:
(r² cos Φ + sin Φ cos Ø) i + (r² sin Φ + sin Φ sin Ø) j + cos Φ k
Note: Units depend on the units used for p, r, and Ø.
If p is in meters, r in centimeters, and Ø in radians, then the units of A and B would be in meters and centimeters, respectively.
to know more about Cartesian coordinates visit:
https://brainly.com/question/8190956
#SPJ11
in boost conveter Vs varies from 8:6 V , Vo=24 , fsw=20 KHz.
C=470µF. and P≥5 W. determine Lmin for CCM. [H.W]
Given that, Vs varies from 8:6 V, Vo = 24 V, fsw = 20 KHz, C = 470 µF, P ≥ 5 W. We need to determine the minimum value of L for continuous conduction mode (CCM).
For a boost converter in continuous conduction mode (CCM), the inductor current, i L never reaches zero. Therefore, the voltage on the inductor never reverses polarity. The voltage transfer ratio (N) of a boost converter is equal to the ratio of the output voltage to the input voltage (i.e. N = Vo / Vs)On-time, Ton = D / fsw where D is the duty cycle.The time for which the inductor is discharging is (1 - D) / fsw.
The average inductor voltage is equal to Vin - (Vo / N)The equation for the average inductor current is given as, Iavg = (Vo * D) / (L * fsw * (1 - D))Now, substituting the given values and simplifying, we get, Lmin = 8.24 µH (approx).The explanation for the above answer is as follows: The voltage transfer ratio (N) of a boost converter is equal to the ratio of the output voltage to the input voltage (i.e. N = Vo / Vs).
To know more about conduction visit:-
https://brainly.com/question/33222532
#SPJ11
If, instead of Eq. (4-70), we choose the Falkner-Skan similarity variable 11 = y(\U\/vx) ¹/², the Falkner-Skan equation becomes
f"' + 2/(m + 1)ff" + m(f² - 1) = 0 subject to the same boundary conditions Eq. (4-72). Examine this relation for the spe- cial case U = -K/x and show that a closed-form solution may be obtained.
The Falkner-Skan equation can be obtained if the Falkner-Skan similarity variable 11 = y(\U\/vx) ¹/² is selected instead of Eq. (4-70).
Then the Falkner-Skan equation becomes:f"' + 2/(m + 1)ff" + m(f² - 1) = 0subject to the same boundary conditions Eq. (4-72).The given problem considers the special case of U = -K/x.
Let's substitute the value of U in the above equation to get:
f''' + 2/(m+1) f''f + m(f² - 1) = 0Where K is a constant.
Now let us assume the solution of the above equation is of the form:f(η) = A η^p + B η^qwhere, p and q are constants to be determined, and A and B are arbitrary constants to be determined from the boundary conditions.
Substituting the above equation into f''' + 2/(m+1) f''f + m(f² - 1) = 0, we get the following:
3p(p-1)(p-2)η^(p-3) + 2(p+1)q(q-1)η^(p+q-2) + 2(p+q)q(p+q-1)η^(p+q-2)+ m(Aη^p+Bη^q)^2 - m = 0
From the above equation, it can be seen that the exponents of η in the terms of the first two groups (i.e., p, q, p-3, p+q-2) are different.
Therefore, for the above equation to hold for all η, we must have:p-3 = 0, i.e., p = 3andp+q-2 = 0, i.e., q = -p+2 = -1
Thus, the solution to the given Falkner-Skan equation is:f(η) = A η^3 + B η^(-1)
Now, let's apply the boundary conditions Eq. (4-72) to determine the values of the constants A and B.
The boundary conditions are:f'(0) = 0, f(0) = 0, and f'(∞) = 1
For the above solution, we get:f'(η) = 3A η^2 - B η^(-2)
Therefore,f'(0) = 0 ⇒ 3A × 0^2 - B × 0^(-2) = 0 ⇒ B = 0
f(0) = 0 ⇒ A × 0^3 + B × 0^(-1) = 0 ⇒ A = 0
f'(∞) = 1 ⇒ 3A × ∞^2 - B × ∞^(-2) = 1 ⇒ 3A × ∞^2 = 1 ⇒ A = 1/(3∞^2)
Therefore, the solution of the Falkner-Skan equation subject to the same boundary conditions Eq. (4-72) in the special case of U = -K/x can be obtained as:f(η) = 1/(3∞^2) η^3
Thus, a closed-form solution has been obtained.
Learn more about equation at
https://brainly.com/question/13145040
#SPJ11