A spring of spring constant 25 N/m is hung vertically and a 0.300 kg mass is attached to one end, causing a displacement of the end of the spring of _____ m.
a. 0.01
b. 0.12
c. 0.77
d. all of the above

Answers

Answer 1

Answer:

The displacement of the spring is 0.12 m.

Explanation:

Given;

spring constant, k = 25 N/m

mass attached to the spring, m = 0.300 kg

displacement of the spring, x = ?

Apply Hook's law, weight of the mass attached (applied force) is directly proportional to the extension of the spring.

F = kx

mg = kx

0.3 x 9.8 = 25x

2.94 = 25x

x = 2.94 / 25

x = 0.12 m

Therefore, the displacement of the spring is 0.12 m.


Related Questions

Help me please..

When the slope of a velocity vs. time graph is negative and constant,
what type of motion is occurring?

A) No motion

B) Constant speed

C) Acceleration

D) Constant Velocity

E) Going in circles

Answers

The answer is Acceleration!

which of the following is true? for this graph.

a. the object increase its velocity.
b. the object decrease its velocity.
c. the objects velocity stays unchanged.
d. the object stays at rest.
e. more information is required.​

Answers

Answer:

b.  The objects velocity is decreasing.

Explanation:

I know this because if you read a graph left to right it will tell u whether it is increasing or decreasing.

WHAT DOES DENSITY HAVE TO DO WITH PLATE TECTONICS?
Explain

Answers

Answer: The reason for the differences in density is the composition of rock in the plates. When two plates come in contact with each other through plate tectonics, scientists can use the density of the plates to predict what will happen. Whichever plate is more dense will sink, and the less dense plate will float over it.

Explanation:

Hope this helps ( not copied and pasted, this answer was done by me so I don't know if it's good or not)

A particular engine has a power output of 2 kW and an efficiency of 27%. If the engine expels 9085 J of thermal energy in each cycle, find the heat absorbed in each cycle. Answer in units of J.

Answers

Answer:

12445 J

Explanation:

Given that

Power output, P = 5 kW

efficiency of the engine, e = 27% = 0.27

Thermal energy expelled, Q(c) = 9085 J

Heat absorbed, Q(h) = ?

Using the formula

e = W/Q(h)

e = [Q(h) - Q(c)] / Q(h)

e = 1 - Q(c)/Q(h)

Now, substituting the values into the formula, we have

0.27 = 1 - 9085/Q(h)

9085/Q(h) = 1 - 0.27

9085/Q(h) = 0.73

Q(h) = 9085 / 0.73

Q(h) = 12445 J

Thus, the heat absorbed is 12445 J

A stone dropped from a bridge strikes the water 5.6 seconds later. What is the final velocity in meters/s?
A) 179.78 meters/s
B) 5.71 meters/s
C) 1.75 meters/s
D) 54.88 meters/s

Answers

Answer: 54.88 meters/s

Explanation:

The final velocity will be calculated by using the formula:

v = u + at

where,

v = final velocity

u = initial velocity = 0

a = 9.8

t = 5.6

Therefore, we slot the value back into the formula. This will be:

v = u + at

v = 0 + (9.8 × 5.6)

v = 0 + 54.88

v = 54.88 meters per second

Therefore, the final velocity is 54.88m/s

20 pts

Which of the following statements is true?
1..LIghtning is a form of statlc energy.

2..Water Is a conductor of electricIty.

3Electricity must flow in a complete circuit.

4 all of the above

Answers

Answer: 2

Explanation:

:}

which factor does not affect the strength of an electromagnet

Answers

Factors Affecting the Strength of the Magnetic Field of an Electromagnet: Factors that affect the strength of electromagnets are the nature of the core material, strength of the current passing through the core, the number of turns of wire on the core and the shape and size of the core.

Pls give Brainiest

Answer:

the placement of the ammeter in the circuit

Explanation:

Can I get help on this question please

Answers

it would be the 3rd one. so C

It would be the 3rd one

An aluminum baking sheet with a mass of 225 g absorbs 2.4 x 104 J from an oven. If its temperature was initially 25 C, what will its new temperature be?

Answers

Answer:

The value is [tex]T_2 =416.9 \ K[/tex]

Explanation:

From the question we are told that

     The mass of the aluminum baking sheet is  [tex]m = 225 \ g = 0.225 \ kg[/tex]

      The energy absorbed is [tex]E = 2.4 *10^{4} \ J[/tex]

       The initial  temperature is  [tex]T_1 = 25 ^oC = 25 + 273 = 298 \ K[/tex]

   

Generally the heat absorbed is mathematically represented as

         [tex]Q = m * c_a * [T_2 - T_1][/tex]

Here  [tex]c_a[/tex] is the specific heat capacity of  aluminum with value  [tex]c_a = 897 \ J / kg \cdot K[/tex]

So

           [tex]2.4 *10^{4 } =0.225 * 897 * [ T_ 2- 298][/tex]

=>         [tex]T_2 - 298 = 118.915[/tex]

=>          [tex]T_2 =416.9 \ K[/tex]

g You heard the sound of a distant explosion (3.50 A/10) seconds after you saw it happen. If the temperature of the air is (15.0 B) oC, how far were you from the site of the explosion

Answers

Answer:

The answer is "1557 meters".

Explanation:

speed of sound in ([tex]\frac{m}{s}[/tex]) [tex]= 331.5 + 0.60 \ T^{\circ}\ C\\\\[/tex]

[tex]\to V = 331.5 + 0.6 \times 24 = 346 \frac{m}{s}\\\\\to t = 4.5 \ seconds \\\\\to S = vt = 346 \times 4.5 = 1557 \ meters[/tex]

A pmdc has a stall torque of 10 and maximum mechanical power of 200. What is the maximum angular velocity?

Answers

Answer:

The maximum angular velocity is 20 rad/s

Explanation:

Given;

torque, τ = 10 N

maximum mechanical power, P = 200 J/s

The output power of the pmdc is given as;

P = τω

where;

P is the maximum mechanical power

ω is the maximum angular velocity

ω = P / τ

ω = (200) / (10)

ω = 20 rad/s

Therefore, the maximum angular velocity is 20 rad/s

A 5 kg block rests on an inclined plane with a coefficient of static friction equal to 0.30. What is the minimum angle at which the block will begin to slide

Answers

Answer:

[tex]\theta = 16.70 ^{\circ}[/tex]

Explanation:

The coefficient of static friction is equal to the tangent of the minimum angle at which an object will begin to start sliding down a ramp.  

[tex]\displaystyle u_s=\frac{F_f}{F_N} = \frac{F_g\ \text{sin}\theta}{F_g\ \text{cos} \theta} = \text{tan} \theta[/tex]

Since we are given the coefficient of static friction we can solve for the minimum angle that the block will begin to slide.

Let's solve for the force of gravity that is acting on the block. The force of gravity is also known as the weight force, which can be calculated by using w = mg.

[tex]w=mg[/tex]

We are given the mass of the block (kg) and we know that g = 9.8 m/s².

[tex]w=(5)(9.8) = 49 \ \text{N}[/tex]

Now we can use this force in the equation:

[tex]\displaystyle u_s = \frac{F_g \ \text{sin} \theta }{F_g \ \text{cos} \theta}[/tex]

Plug [tex]\displaystyle u_s = 0.30[/tex] and 49 N into the equation.

[tex]\displaystyle 0.30 = \frac{(49) \ \text{sin} \theta }{(49) \ \text{cos} \theta}[/tex]  [tex]0.30=\text{tan} \theta[/tex]

Notice that the gravitational force cancels out in the end, so we can actually start with [tex]0.30=\text{tan} \theta[/tex].

Evaluate this equation by taking the inverse tangent of both sides of the equation.

[tex]\text{tan}^-^1 (0.30) = \text{tan}^-^1 (\text{tan}\theta)[/tex] [tex]\text{tan}^-^1 (0.30) =\theta[/tex] [tex]\theta = 16.69924423[/tex]

The minimum angle at which the block will begin to slide is about 16.70 degrees.

10. A boy weighs 475 N. What is his mass? (acceleration due to gravity on Earth is 9.8m/s2 = g)


Answers

Answer: mass = 48.47 kg.

Explanation:

Formula : Weight = mg  , where m = mass of body , g= acceleration due to gravity .

Given: Weight  = 475 N

[tex]g= 9.8\ m/s^2[/tex]

Substitute all values in formula ,  we get

[tex]475= m \times9.8\\\\\Rightarrow\ m = \dfrac{475}{9.8}\\\\\Rightarrow\ m \approx 48.47\ kg[/tex]

Hence, his mass = 48.47 kg.

ANSWER THIS FOR 16 POINTS!!!!!!!!!!

When hitting the ski slopes when does the skier has the most potential energy??

Answers

Answer:

As the ski jumper starts moving downhill, some of his potential energy changes into kinetic energy (KE). Kinetic energy moves him down the slope to the ramp. When the ski jumper takes off from the ramp, some of his kinetic energy is changed back into potential energy as he rises in the air.

Explanation: hope this helps

Answer:

at the top of the slope

Explanation:

A school bus has a mass of 18,200 kg. The bus moves at 13.5 m/s. How fast must a 0.142-kg baseball move in order to have the same momentum as the bus?

Answers

Answer:

bus momentum

p_bus= m_bus x v_bus

=18,200 x 16.5

basball momentum

pball=mball x vball

=0.142 x v

p_bus = pball

18200 x 16.5 = 0.142 x v

v=(18200 x 16.5)/0.142

v is the answer for baseball

Explanation:

⚠️not my answer tryna be honest here⚠️

The momentum of the bus of 18200 kg and velocity of 13.5 m/s is 245700 Kg m/s. To have equal momentum the base ball with 145 g have to throw in a speed of 1.7 × 10 ⁶  m/s.

What is momentum?

Momentum of a moving body is the product of mass and velocity. Thus it have the unit of g m/s or Kg m/s. Momentum is a vector quantity and thus having magnitude and direction.

Given that one bus is having a mass of  18200 Kg and 13.2  m/s speed. The momentum is:

p = mv

 =18200 kg × 13.5  m/s

 = 245700 Kg m/s

To have a momentum of 245700 Kg m/s   the base ball with 0. 142 g have to have a velocity  = 245700 Kg m/s   / 0.142 g

                          =1.7 × 10 ⁶  m/s

Hence, the baseball weighs0. 142 g have to move in 1.7 × 10 ⁶  m/s

To find more on momentum, refer here:

http://brainly.com/question/24030570

#SPJ2

A balloon contains 0.075 m^3 of
gas. The pressure is reduced to
100kPa and fills a box of 0.45 m^3.
What is the initial pressure inside the
balloon if the temperature remains
constant?

Answers

Answer:

600 KPa.

Explanation:

From the question given above, the following data were obtained:

Initial volume (V1) = 0.075 m³

Final volume (V2) = 0.45 m³

Final pressure (P2) = 100 KPa

Initial pressure (P1) =?

Temperature = constant

The initial pressure can be obtained by using the Boyle's law equation as shown below:

P1V1 = P2V2

P1 × 0.075 = 100 × 0.45

P1 × 0.075 = 45

Divide both side by 0.075

P1 = 45 / 0.075

P1 = 600 KPa.

Thus, the initial pressure in the balloon is 600 KPa.

A 1 200-kg automobile moving at 25 m/s has the brakes applied with a deceleration of 8.0 m/s2. How far does the car travel before it stops?

Answers

Answer:

Δx = 39.1 m

Explanation:

Assuming that deceleration keeps constant during the braking process, we can use one of the kinematics equations, as follows:

        [tex]v_{f} ^{2} - v_{o} ^{2} = 2* a * \Delta x (1)[/tex]

        where  vf is the final velocity (0 in our case), v₀ is the initial velocity

        (25 m/s), a is the acceleration (-8.0 m/s²), and Δx is the distance

        traveled since the brakes are applied.

Solving (1) for Δx, we have:

        [tex]\Delta x = \frac{-v_{o} ^{2} }{2*a} = \frac{-(25m/s)^{2}}{2*(-8.0m/s2} = 39.1 m (2)[/tex]        

The car will travel a distance of 39.1 m before its stops.

To solve the problem above, use the equations of motion below.

Equation:

v² = u²+2as................... Equation 1

Where:

v = final velocity of the automobileu = initial velocity of the automobilea = accelerations = distance covered

From the question,

Given:

v = 0 m/s (before its stops)u = 25 m/sa = -8 m/s² (decelerating)

Substitute these values into equation 1

⇒ 0² = 25²+2(-8)(s)

Solve for s

⇒ 0²-25² = -16s⇒ -16s = -625⇒ s = -625/16⇒ s = 39.1 m

Hence, The car will travel a distance of 39.1 m before its stops.

Learn more about acceleration here: https://brainly.com/question/605631

A bullet fired into a fixed target loses half of its velocity after penetrating 3 cm. How much further it will penetrate before coming to rest assuming that it faces constant resistance to motion​

Answers

[tex]{\mathfrak{\underline{\purple{\:\:\: Given:-\:\:\:}}}} \\ \\[/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{First \: penetrating \: length\:(s_{1}) = 3 \: cm}[/tex]

[tex]\\[/tex]

[tex]{\mathfrak{\underline{\purple{\:\:\:To \:Find:-\:\:\:}}}} \\ \\[/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{Left \: Penetration \: length \: before \: it \: comes \: to \: rest \:( s_{2} )}[/tex]

[tex]\\[/tex]

[tex]{\mathfrak{\underline{\purple{\:\:\: Calculation:-\:\:\:}}}} \\ \\[/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{Let \: Initial \: velocity = v\:m/s} \\\\[/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{Left \: velocity \: after \: s_{1} \: penetration = \dfrac{v}{2} \:m/s} \\\\ [/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{s_{1} = \dfrac{3}{100} = 0.03 \: m}[/tex]

[tex]\\[/tex]

☯ As we know that,

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ {v}^{2} = {u}^{2} + 2as }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ \bigg(\dfrac{v}{2} \bigg)^{2} = {v}^{2} + 2a s_{1}}[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ \dfrac{ {v}^{2} }{4} = {v}^{2} + 2 \times a \times 0.03 }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ \dfrac{ {v}^{2} }{4} - {v}^{2} = 0.06 \times a }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{\dfrac{ - 3{v}^{2} }{4} = 0.06 \times a }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{a = \dfrac{ - 3 {v}^{2} }{4 \times 0.06} }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ a = \dfrac{ - 25 {v}^{2} }{2}\:m/s^{2} ......(1) }[/tex]

[tex]\\[/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{ Initial\:velocity=v\:m/s} \\\\ [/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{ Final \: velocity = 0 \: m/s }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ {v}^{2} = {u}^{2} + 2as}[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{{0}^{2} = {v}^{2} + 2 \times \dfrac{ - 25 {v}^{2} }{2} \times s }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ - {v}^{2} = - 25 {v}^{2} \times s }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ s = \dfrac{ - {v}^{2} }{ - 25 {v}^{2} }}[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ s = \dfrac{1}{25} }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ s = 0.04 \: m }[/tex]

[tex]\\[/tex]

☯ For left penetration (s₂)

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{s = s_{1} + s_{2} }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ 0.04 = 0.03 + s_{2}}[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ s_{2} = 0.04 - 0.03 }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{s_{2} = 0.01 \: m = {\boxed{\sf{\purple{1 \: cm }}} }}[/tex]

[tex]\\[/tex]

[tex]\star\:\sf{Left \: penetration \: before \: it \: come \: to \: rest \: is \:{\bf{ 1 \: cm}}} \\ [/tex]

A book is sitting on a table. Which of the following is true about the table?

Answers

Answer:

Its pulling down on the book

Explanation: if it was pushing up the book would be floating and the other choices don't make sense

Answer:
C


Hope this helps!! :D

Part A:
The primary coil of a transformer contains 100 turns; the secondary has 200 turns. The primary coil is connected to a size-AA battery that supplies a constant voltage of 1.5 volts. What voltage would be measured across the secondary coil?
Part B:
A transformer is intended to decrease the value of the alternating voltage from 500 volts to 25 volts. The primary coil contains 200 turns. Find the necessary number of turns N2 in the secondary coil.
Part C:
A transformer is intended to decrease the value of the alternating current from 500 amperes to 25 amperes. The primary coil contains 200 turns. Find the necessary number of turns N2 in the secondary coil.
Part D:
In a transformer, the primary coil contains 400 turns, and the secondary coil contains 80 turns. If the primary current is 2.5 amperes, what is the secondary current I2?
Part E:
The primary coil of a transformer has 200 turns and the secondary coil has 800 turns. The power supplied to the primary coil is 400 watts. What is the power generated in the secondary coil if it is terminated by a 20-ohm resistor?
Part F:
A transformer supplies 60 watts of power to a device that is rated at 20 volts. The primary coil is connected to a 120-volt ac source. What is the current I1 in the primary coil?
Part G:
The voltage and the current in the primary coil of a nonideal transformer are 120 volts and 2.0 amperes. The voltage and the current in the secondary coil are 19.4 volts and 11.8 amperes. What is the efficiency e of the transformer? The efficiency of a transformer is defined as the ratio of the output power to the input power, expressed as a percentage: e=100Pout/Pin.

Answers

Answer:

a) 0 V

b) 10 turns

c) 4000 turns

d) 12.5 A

e) 400 W

f) 0.5 A

g) 95.4%

Explanation:

A

0

B

To solve this, we would be using the simple relationship between voltage and number of turns

V1/V2 = N1/N2

500/25 = 200/N2

20 = 200/N2

N2 = 200/20

N2 = 10 turns

C

Here also, we would be using the relationship between current and the number of turns

I1/I2 = N2/N1

500/25 = N2/20

20 = N2/20

N2 = 20 * 20

N2 = 4000 turns

D

Like in the previous question, current and the number of turn relationship is used

N1/N2 = I2/I1

400/80 = I2/2.5

5 = I2/2.5

I2 = 5 * 2.5

I2 = 12.5 A

E

The power remains unchanged at 400 W

F

Power = Voltage * Current

P = VI

I = P/V

I = 60/120

I = 0.5 A

G

95.4%

The transformer is a device used to step up or step down voltage.

Part A;

Given that;

Es/Ep = Ns/Np

Es = voltage in the secondary coil

Ep = voltage in primary coil

Ns = Number of turns in secondary coil

Np = Number of coils in primary coil

Es = Ns/Np ×  Ep

Es = 200/100  × 1.5 V

Es = 3 V

Part B

Ns = Es/Ep × Np

Ns = 25/500 × 200

Ns = 10 turns

Part C

Ns/Np = Ip/Is

Ns = Ip/Is × Np

Ns = 500/25 × 200

Ns = 4000 turns

Part D

Ns/Np = Ip/Is

NsIs = NpIp

Is = NpIp/Ns

Is = 400 × 2.5/80

Is =12.5 A

Part E

The power in the primary coil is the same as the power in the secondary coil. The power in the secondary coil is 400 watts.

Part F

Power supplied = 60 watts

Voltage of primary coil = 120 V

Since;

P = IV

I = P/V = 60/120 = 0.5 A

Part G

Since;

E = 100Pout/Pin

Pin = 120 V × 2 A = 240 W

Pout =  19.4 V ×  11.8 A = 228.92 W

E = 100(228.92/240)

E = 95.4%

Learn more: https://brainly.com/question/8646601

A truck pushes a pile of dirt horizontally on a frictionless road with a net force of
20

N
20N20, start text, N, end text for
15.0

m
15.0m15, point, 0, start text, m, end text.
How much kinetic energy does the dirt gain?

Answers

Answer:

300 Joules

Explanation:

This is a common question on Khan Academy's "Calculating change in kinetic energy from a force" practice exercises. (AP Physics 1)

The simplest method to use is the following: [tex]W = F * d * cos(theta)[/tex], where W represents work (joules), F represents force (newtons), d represents distance (meters), and theta represents the angle of the force that's being applied.In this scenario, the force being applied is horizontal, so we can remove the [tex]cos(theta)[/tex] from our equation.So, our equation is now: [tex]W = F * d[/tex]. This would mean that [tex]W = 20 * 15[/tex], which is equal to [tex]300[/tex]. Our answer is 300 joules. (this value is positive and not negative because kinetic energy is being GAINED, not LOST)

Here's the real question without all the formatting:

A truck pushes a pile of dirt horizontally on a frictionless road with a net force of 20 N for 15.0 m. How much kinetic energy does the dirt gain?

A truck pushes a pile of dirt in the horizontal direction with a force of 20 N to a distance of 15 m then the kinetic energy of the dirt is 300 J.

What is work?

In physics, the term "work" refers to the measurement of energy transfer that takes place when an item is moved over a distance by an externally applied, at least a portion of which is applied inside the direction of the displacement.

The duration of the path is multiplied by the component of a force acting along the path to calculate work if the forces are constant. The work W is theoretically equivalent to the pressure f times the range d, or W = fd, to represent this idea. Work is done when a force is applied at an angle of to a displacement, or W = fd cos.

The work done, [tex]W = Force * Displacement[/tex]

W = 15× 20

W = 300 J

To know more about Work:

https://brainly.com/question/18094932

#SPJ3

Two clear but non-mixing liquids each of depth 15 cm are placed together in a glass container. The liquids have refractive indices of 1.75 and 1.33. What is the apparent depth of the combination when viewed from above?

Answers

Answer:

The apparent depth d = 19.8495 cm

Explanation:

The equation for apparent depth can be expressed as:

[tex]d = \dfrac{d_1} {\mu_1}+\dfrac {d_2}{\mu_2}[/tex]

here;

[tex]d_1 = d_2 = 15 \ cm[/tex]

[tex]\mu_1[/tex] = refractive index in the first liquid = 1.75

[tex]\mu_2[/tex] = refractive index in the second liqquid= 1.33

[tex]d = \dfrac{15}{1.75}+\dfrac{15}{1.33}[/tex]

[tex]d = 15( \dfrac{1}{1.75}+\dfrac{1}{1.33})[/tex]

[tex]d = 15( 0.5714 +0.7519)[/tex]

d = 15(1.3233 ) cm

d = 19.8495 cm

What differentiates galaxy groups from clusters?
A.
Clusters are bigger than groups.
B.
Clusters are more massive than groups.
C.
Clusters contain a hot intracluster medium, whereas groups do not.
D.
Clusters are collections of galaxy groups, whereas groups are collections of galaxies.
E.
Clusters don't gravitationally bind galaxies together, while groups bind galaxies gravitationally.

Answers

Answer:

A

Explanation:

Galaxy clusters are basically very large (>50 galaxies) groups

Answer:

The correct answer would be:

C.

Clusters contain a hot intracluster medium, whereas groups do not.

#PLATOFAM

Have a nice day!

a cyclist accelerates at a rate of 7.0 m/s2. how long will it take the cyclist to go from a velocity of 4 m/s to a velocity of 18 m/s?​

Answers

Answer:

2.57 seconds  (rounded to 2.6 Seconds)

Step-by-step explanation:

Great question, it is always good to ask away and get rid of any doubts that you may be having.

Before we can solve this question we need to create a formula that calculates the final speed. The formula will be the following,

Where:

Vf is the final Velocity

Vi is the initial velocity

A is the acceleration

t is the time in seconds

Now that we have the formula we can plug in the values given to us in the question and solve for the amount of time (t).

Finally, we can see that it would take the cyclist 2.57 seconds (approximately) to reach a speed of 18 m/s

I hope this answered your question. If you have any more questions feel free to ask away at Brainly.

A speeding race car primarily contains potential energy.

:True
False

Answers

True because is aid sooooo

The image below shows four boxes that each contain a different sample of gas. The atoms of each gas are represented by dots, 1 2 3 4 Which box contains the gas with the greatest density?

A. 1
B. 2
C. 3
D. 4​

Answers

4 there r more dots

The speed of revolution of particle going around a circlr is doubled and its angular speed is havled. What happen to the centripetal acceleration?
a) unchanged
b) doubles
c) halves
d) becomes four times​

Answers

Answer: The correct answer is C

Explanation:

A ball is throw at an angle of 30 degrees off the horizontal, with an initial velocity of 28 m/s. what is the maximum height the ball will reach?​

Answers

[tex]{\mathfrak{\underline{\purple{\:\:\: Given:-\:\:\:}}}} \\ \\[/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{Angle \ of \ projection = 30^{\circ} }[/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{Initial \ velocity \ of \ projectile = 28 \: m/s^{-1} }[/tex]

[tex]\\[/tex]

[tex]{\mathfrak{\underline{\purple{\:\:\:To \:Find:-\:\:\:}}}} \\ \\[/tex]

[tex]\:\:\:\:\bullet\:\:\:\sf{Height_{\:(max)}\: reached\: by \:the \:projectile }[/tex]

[tex]\\[/tex]

[tex]{\mathfrak{\underline{\purple{\:\:\: Calculation:-\:\:\:}}}} \\ \\[/tex]

As we know that,

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ H = \dfrac{u^2\;sin^2\theta}{2\;g} }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{H = \dfrac{(28)^2\;sin^2 30^{\circ}}{2\;(9.8)} }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{H = \dfrac{784 \times \;sin^230^{\circ}}{19.6} }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ H = \dfrac{784}{19.6}\times sin^2 30^{\circ}}[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ H = \dfrac{784}{19.6}\times \bigg(\dfrac{1}{2}\bigg)^2 }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: \sf{ H = \dfrac{784}{19.6}\times \dfrac{1}{4} }[/tex]

[tex]\\[/tex]

[tex]\dashrightarrow\:\: {\boxed{\sf{H=10\:m }}}[/tex]

why do feet smell and noses run?

Answers

Answer:

Nose has mucous glands with hairs which helps the body in trapping pollutants and infectants from entering inside the body. On the other hand,our feet is composed of millions of sweat pores when dirt and other things accumulate,it smells because of sweat mixed with the dirt and other dirty things of the ground.

Explanation:

Hope this helps

Bob Beamon's 1968 Olympic long jump set a world record which remains unbroken to this day. This amazing jump resulted from an initial velocity of 9.5 m/s at an angle of 40 degrees from the horizontal.
1. Calculate the initial horizontal velocity (V_ix) to two significant figures:

2. Calculate the initial vertical velocity (V_iy) to two significant figures:

3. Calculate the time needed to reach the highest point of the jump (t_1/2) to two significant figures:

4. Calculate the total time (t_TOT) needed to complete the jump to two significant figures:

5. Calculate the maximum height (h) reached during the jump to two significant figures:

6. Calculate the range (total horizontal distance) of his jump to two significant figures:

Please answer today! Thanks!

Answers

Answer:

1.) 7.3 m/s 2.) 6.1 m/s

Explanation:

To calculate the initial horizontal velocity with just degrees and velocity alone is pretty simple. The formula is     Velocity*cos(degrees)

eg 9.5*cos(40)

2.  To calculate the initial vertical velocity with just degrees and velocity alone is pretty simple. The formula Velocity*sin(degrees)

eg 9.5*sin(40)

Other Questions
8-4x for x = 9The expression equals I what is 6+ 4 - 2 first to answer gets brainlist Bone deformities occur due to the excess intake ofA) Phosphore B) PotassiumC) Fatty acid D) Fluorine Find the slope of the line that passes through A(2, 1), B(1, 1) A)1/2 B)-1/2 C)-2/1 D)2/1 write sentences about political parties in which you use the following terms : political party, two-party system, third party, platform, plank (31) The rough endoplasmic reticulum (A) has ribosomes bound to it(B) is part of the membrane system found throughout the cells cytoplasm (C) is connected to the nuclear envelope(D) all of the above can u pls help me with this question aWhich of the following would be considered a short term goal?Becoming a teacher06 Failing an examOc Resolving a conflictodLosing 20 pounds Find the measure of each angle indicated I need the answers, help please! Mistletoe is a green plant that can make its own food, but also derives food from the mesquite tree on which it lives. In this way mistletoe is able to steal water and valuable minerals from the tree. 1. What is the advantage and disadvantage of this relationship to each organism? 2. What would happen to the mistletoe population if mesquite trees increase in number? 3. What type of symbiosis is this? Match the Chinese holiday to the correct date HELP PLEASE!!!!!!!!!! HELPPPP PLEASEEEE!!!!! Why does Salva describe volleyball as a language? Use evidence from the text to support your response. Why is deforestation an issue for the climate? Can someone pls help me How does the nervous system and cardiovascular system interact?This is a question for my semester exam so someone PLEASE ANSWER THIS!!! Can someone help me on this? this one is confusing.... Write a linear function f with the values f(0) = -4 and f (5) = 11. answer these 2 questions for 50 points please