A satellite orbits the earth at a distance of 1.50 × 10^{7} m above the planetʹs surface and takes 8.65 hours for each revolution about the earth. The earthʹs radius is 6.38 × 10^{6} m. The acceleration of this satellite is closest to

Answer:

The tension in the cable is 18371.9 newtons.

Explanation:

Physically speaking, the tension can be calculated with the help of the Second Newton's Law. The upward acceleration means that magnitude of tension must be greater than weight of elevator, whose equation of equilibrium is described below:

[tex]\Sigma F = T - m\cdot g = m \cdot a[/tex]

Where:

[tex]T[/tex] - Tension in the cable, measured in newtons.

[tex]m[/tex] - Mass of the elevator, measured in kilograms.

[tex]g[/tex] - Gravity constant, measured in meters per square second.

[tex]a[/tex] - Net acceleration of the elevator, measured in meters in square second.

Now, tension is cleared and resultant expression is also simplified:

[tex]T = m \cdot (a + g)[/tex]

If [tex]m = 1700\,kg[/tex], [tex]a = 1\,\frac{m}{s^{2}}[/tex] and [tex]g = 9.807\,\frac{m}{s^{2}}[/tex], the tension in the cable is:

[tex]T = (1700\,kg)\cdot \left(1\,\frac{m}{s^{2}}+9.807\,\frac{m}{s^{2}} \right)[/tex]

[tex]T = 18371.9\,N[/tex]

The tension in the cable is 18371.9 newtons.

Answer:maximum

Explanation:

Answer:

If a key is pressed on a piano, the frequency of the resulting sound will determine the ___PITCH_____, and the amplitude will determine the _____LOUDNESS___ of the perceived musical note.

Explanation:

The frequency of a vibrating string is primarily based on three factors:

The sounding length (longer is lower, shorter is higher)

The tension on the string (more tension is higher, less is lower)

The mass of the string, normally based on a uniform density per unit length (higher mass is lower, lower mass is higher)

To make a shorter string (such as in an upright piano) sound the same fundamental frequency as a longer string (such as in a 9' grand piano), either the thickness of the string must be increased (which increases the density and the mass) or the tension must be decreased, and usually it's a bit of both.

Thicker strings are often stiffer and that creates more inharmonic partials, and lower tension is associated with other problems, so the best way to make a string sound lower is the make it longer, but it is not practical to make a piano from strings that are all the same density and tension, because the lowest strings would have to be ridiculously long. Nine feet is already a great demand on space for a single musical instrument, and of course those pianos are extremely expensive and difficult to move.

And alsoBesides the pitch of a musical note, perhaps the most noticeable feature in how loud the note is. The loudness of a sound wave is determined from its amplitude. While loudness is only associated with sound waves, all types of waves have an amplitude. Waves on a calm ocean may be less than 1 foot high. Good surfing waves might be 10 feet or more in amplitude. During a storm the amplitude might increase to 40 or 50 feet.

Many things can influence the amplitude.

What is producing the sound?

How far are you from the source of the sound? The farther away the smaller the amplitude.

Intervening material. Sound does not travel through walls as well as air.

Depends on what is detecting the wave sound. Ear vs. microphone.

Answer:

The frequency will determine the pitch

the amplitude will determine the loudness

Explanation:

The frequency of a sound refers to the number of vibrations made by the sound wave produced in a unit of time. This usually affects how high or how low a note is perceived in music. High-frequency sounds have higher pitches, while low-frequency sounds have lower pitches.

The amplitude of a sound wave refers to the height between the wave crests and the equilibrium line in a sound wave. It shows how loud a sound will be. High amplitude sounds are loud while low amplitude sounds are quiet.

Answer:

P' = 4 P

Therefore, the power dissipated by the circuit will becomes four times of its initial value.

Explanation:

The power dissipation by an electrical circuit is given by the following formula:

Power Dissipation = (Voltage)(Current)

P = VI

but, from Ohm's Law, we know that:

Voltage = (Current)(Resistance)

V = IR

Substituting this in formula of power:

P = (IR)(I)

P = I²R   ---------------- equation 1

Now, if we double the current , then the power dissipated by that circuit will be:

P' = I'²R

where,

I' = 2 I

Therefore,

P' = (2 I)²R

P' = 4 I²R

using equation 1

P' = 4 P

Therefore, the power dissipated by the circuit will becomes four times of its initial value.

What is the velocity of a 900-kg car initially moving at 30.0 m/s, just after it hits a 150-kg deer initially running at 18.0 m/s in the same direction? Assume the deer remains on the car.

28.29m/s

In this situation, linear momentum is conserved. And since the deer remains on the car after collision, the linear momentum is given as;

([tex]m_{C}[/tex] x [tex]u_{C}[/tex]) + ([tex]m_{D}[/tex] x [tex]u_{D}[/tex]) = ([tex]m_{C}[/tex] + [tex]m_{D}[/tex]) v            -----------------(i)

Where;

[tex]m_{C}[/tex] = mass of car

[tex]u_{C}[/tex] = initial velocity of car before collision

[tex]m_{D}[/tex] = mass of deer

[tex]u_{D}[/tex] = initial velocity of the deer before collision

v = common velocity with which the car and the deer move after collision

From the question;

[tex]m_{C}[/tex] = 900kg

[tex]u_{C}[/tex] = +30.0m/s    (direction of the motion of the car taken positive)

[tex]m_{D}[/tex] = 150kg

[tex]u_{D}[/tex] = +18.0m/s    (relative to the direction of the car, the velocity of the deer is also positive )

Substitute these values into equation (i) as follows;

(900 x 30.0) + (150 x 18.0) = (900 + 150)v

27000 + 2700 = 1050v

29700 = 1050v

v = [tex]\frac{29700}{1050}[/tex]

v = 28.29m/s

Therefore, the velocity of the car after hitting the deer is 28.29m/s. This is also the velocity of the deer after being hit by the car.

Answer:

Explanation:

For sound level in decibel scale the relation is

dB = 10 log I / I₀ where I₀ = 10⁻¹² and I is intensity of sound whose decibel scale is to be calculated .

Putting the given values

61 = 10 log I / 10⁻¹²

log I / 10⁻¹² = 6.1

I = 10⁻¹² x 10⁶°¹

[tex]=10^{-5.9}[/tex]

intensity of sound of 5 persons

[tex]I=5\times 10^{-5.9}[/tex]

[tex]dB=10log\frac{5 X 10^{-5.9}}{10^{-12}}[/tex]

= 10log 5 x 10⁶°¹

= 10( 6.1 + log 5 )

= 67.98

sound level will be 67.98 dB .

Answer:

The magnitude of the current in the wire is 5.5A, and the direction of the current is in the positive y direction.

Explanation:

- To find the direction of the conventional current in the wire you use the following formula:

[tex]\vec{F}=i\vec{l}\ X\ \vec{B}[/tex]       (1)

i: current in the wire = ?

F: magnitude of the magnetic force on the wire = 15.1N

B: magnitude of the magnetic field = 6.1T

l: length of the wire that is affected by the magnetic field = 0.45m

The direction of the magnetic force is in the x direction (+^i) and the direction of the magnetic field is in the +z direction (+^k).

The direction of the current must be in the +y direction (+^j). In fact, you have:

^j X ^k = ^i

The current and the magnetic field are perpendicular between them, then, you solve for i in the equation (1):

[tex]F=ilBsin90\°\\\\i=\frac{F}{lB}=\frac{15.1N}{(0.45m)(6.1T)}=5.5A[/tex]

The magnitude of the current in the wire is 5.5A, and the direction of the current is in the positive y direction.

Answer:

I can help

Explanation:

Answer:

r = 0.405m = 40.5cm

Explanation:

In order to calculate the length of the string between Wanda and the ball, you take into account that the tension force is equal to the centripetal force over the ball. So, you can use the following formula:

[tex]F_c=ma_c=m\frac{v^2}{r}[/tex]       (1)

Fc: centripetal acceleration (tension force on the string) = 12N

m: mass of the ball = 60g = 0.06kg

r: length of the string = ?

v: linear speed of the ball = 9.0m/s

You solve for r in the equation (1) and replace the values of the other parameters:

[tex]r=\frac{mv^2}{F_c}=\frac{(0.06kg)(9.0m/s)^2}{12N}=0.405m[/tex]

The length of the string between Wanda and the ball is 0.405m = 40.5cm

Answer:

The charge stored in the capacitor will stay the same. However, the electric potential across the two plates will increase. (Assuming that the permittivity of the space between the two plates stays the same.)

Explanation:

The two plates of this capacitor are no longer connected to each other. As a result, there's no way for the charge on one plate to move to the other. [tex]Q[/tex], the amount of charge stored in this capacitor, will stay the same.

The formula [tex]\displaystyle Q = C\, V[/tex] relates the electric potential across a capacitor to:

While [tex]Q[/tex] stays the same, moving the two plates apart could affect the potential [tex]V[/tex] by changing the capacitance [tex]C[/tex] of this capacitor. The formula for the capacitance of a parallel-plate capacitor is:

[tex]\displaystyle C = \frac{\epsilon\, A}{d}[/tex],

where

Assume that the two plates are separated with vacuum. Moving the two plates apart will not affect the value of [tex]\epsilon[/tex]. Neither will that change the area of the two plates.

However, as [tex]d[/tex] (the distance between the two plates) increases, the value of [tex]\displaystyle C = \frac{\epsilon\, A}{d}[/tex] will become smaller. In other words, moving the two plates of a parallel-plate capacitor apart would reduce its capacitance.

On the other hand, the formula [tex]\displaystyle Q = C\, V[/tex] can be rewritten as:

[tex]V = \displaystyle \frac{Q}{C}[/tex].

The value of [tex]Q[/tex] (charge stored in this capacitor) stays the same. As the value of [tex]C[/tex] becomes smaller, the value of the fraction will become larger. Hence, the electric potential across this capacitor will become larger as the two plates are moved away from one another.  

Answer:

Yes the monkey will get hit and it will not avoid the dart.

Explanation:

Yes, the monkey will be hit anyway because the dart will follow a hyperbolic path and and will thus fall below the branches, so if the monkey jumps it will be hit.

No, the monkey will not avoid the dart because dart velocity doesn't matter. The speed of the bullet doesn’t even matter in this case because a faster bullet will hit the monkey at a higher height and while a slower bullet will simply hit the monkey closer to the ground.

Answer:

  315,000 ft·lb

Explanation:

At 300 ft and 5 lb/ft, the weight of the cable is (300 f)(5 lb/ft) = 1500 lb. The work done to raise it is equivalent to the work done to raise the cable's center of mass. Since the cable is of uniform density, its center of mass is half the cable length below the winch.

  total work done = work to raise cable + work to raise load

  = (1500 lb)(150 ft) +(300 lb)(300 ft) = 315,000 ft·lb

The position of a particle is r(t)= (4.0t²i+ 2.4j- 5.6tk) m. (Express your answers in vector form.)

(a) Determine its velocity (in m/s) and acceleration (in m/s²) as functions of time. (Use the following as necessary: t. Assume t is seconds, r is in meters, and v is in m/s, Do not include units in your answer.)

v(t)= ________m/s

a(t)= ________m/s²

(b) What are its velocity (in m/s) and acceleration (in m/s²) at time t 0?

v(0) =_______ m/s

a(0)=_______ m/s²

(a)

v(t)= [tex]8ti - 5.6k[/tex] m/s

a(t)= 8i m/s²

(b)

v(0) = -5.6k m/s

a(0)= 8i m/s²

From the question, the position of the particle is given by;

r(t)= (4.0t²i+ 2.4j- 5.6tk)        -----------------(i)

(a)

(i)To get the velocity, v(t), of the particle, we'll take the first derivative of the position of the particle (given by equation (i)) with respect to time, t, as follows;

v(t) = [tex]\frac{dr(t)}{dt}[/tex] = [tex]\frac{d(4.0t^2i + 2.4j - 5.6tk)}{dt}[/tex]

v(t) = [tex]\frac{dr(t)}{dt}[/tex] = [tex]8ti +0j - 5.6k[/tex]

v(t) = [tex]8ti - 5.6k[/tex]          --------------------(ii)

(ii) To get the acceleration, a(t), of the particle, we'll take the first derivative of the velocity of the particle (given by equation (ii)) with respect to time, t, as follows;

a(t) = [tex]\frac{dv(t)}{dt}[/tex]  = [tex]\frac{d(8ti - 5.6k)}{dt}[/tex]

a(t) = 8i                    --------------------(iii)

(b)

(i) To get the velocity of the particle at time t = 0, substitute the value of t = 0 into equation (ii) as follows;

v(t) = [tex]8ti - 5.6k[/tex]  

v(0) = 8(0)i - 5.6k

v(0) = 0 - 5.6k

v(0) = -5.6k

(ii) To get the acceleration of the particle at time t = 0, substitute the value of t = 0 into equation (iii) as follows;

a(t) = 8i

a(0) = 8i

Answer:

Fermat's principle states that the path taken by a ray between two given points is the path that can be traversed in the least time.

Thus this least distance being the same as least time will only apply to reflection alone because in reflection light travels In the same direction so least distance will also mean least time. But for refraction light travels in different mediums at different speeds so least distance and least time paths will definately not be the same

Complete question:

Two cars start moving from the same point. One travels south at 28 mi/h and the other travels west at 21 mi/h. At what rate is the distance between the cars increasing four hours later.

Answer:

The rate at which the distance between the cars is increasing four hours later is 35 mi/h.

Explanation:

Given;

speed of one car, dx/dt = 28 mi/h South

speed of the second car, dy/dt = 21 mi/h West

The distance between the cars is the line joining west to south, which forms a right angled triangle with the two positions.

Apply Pythagoras theorem to evaluate this distance;

let the distance between the cars = z

x² + y² = z² -------- equation (1)

Differentiate with respect to time (t)

[tex]2x\frac{dx}{dt} + 2y\frac{dy}{dt} = 2z\frac{dz}{dt}[/tex] ----- equation (2)

Since the speed of the cars is constant, after 4 hours their different distance will be;

x: 28(4) = 112 mi

y: 21(4) = 84 mi

[tex]z = \sqrt{x^2 + y^2} \\\\z = \sqrt{112^2 + 84^2} \\\\z = 140 \ mi[/tex]

Substitute in the value of x, y, z, dx/dt, dy /dt into equation (2) and solve for dz/dt

[tex]2x\frac{dx}{dt} + 2y\frac{dy}{dt} = 2z\frac{dz}{dt} \\\\2(112)(28) + 2(84)(21) = 2(140)\frac{dz}{dt} \\\\9800 = 280\frac{dz}{dt} \\\\\frac{dz}{dt} = \frac{9800}{280} \\\\\frac{dz}{dt} = 35 \ mi/h[/tex]

Therefore, the rate at which the distance between the cars is increasing four hours later is 35 mi/h

Answer:

Wmax = 63.65 ≈ 64 lb

Explanation:

Answer:

the kinetic energy lost in the collison is a) 30 J

Explanation:

given data

mass of door m1 = 35 kg

width a = 90 cm = 0.9 m

the mass of ball  m2 = 500 g = 0.5 kg

initial speed of ball  u = 20 m/s

final speed of ball  v = 16 m/s

r = 60 cm = 0.6 m

soluion

we will consider here final angular speed of the door = w

so now we use conservation of angular momentum  that is

Li = Lf    ........................1

that is express as

m2 × u × r = I × w + m2 × v × r

put here value and we get  

0.5 × 20 × 0.6 = [tex](m1 \times \frac{a^2}{12})[/tex] × w + 0.5 × 16 × 0.6

solve it we get

w = 0.508 rad/s

so that here

the kinetic energy lost in the collison,

KE = KE initial - KE final     ..................2

put here value

KE = 0.5 × m2 × u² - (0.5 × I × w² + 0.5 × m2 × v²)

KE = 0.5 × (0.5 × 20² - (35 × 0.9² ÷ 12) × 0.508² - 0.5 × 16²) J

KE = 30 J

the kinetic energy lost in the collison is a) 30 J

Answer:

375 and 450

Explanation:

The computation of the initial and the final temperature is shown below:

In condition 1:

The efficiency of a Carnot cycle is [tex]\frac{1}{6}[/tex]

So, the equation is

[tex]\frac{1}{6} = 1 - \frac{T_2}{T_1}[/tex]

For condition 2:

Now if the temperature is reduced by 75 degrees So, the efficiency is [tex]\frac{1}{3}[/tex]

Therefore the next equation is

[tex]\frac{1}{3} = 1 - \frac{T_2 - 75}{T_1}[/tex]

Now solve both the equations

solve equations (1) and (2)

[tex]2(1 - T_2/T_1) = 1 - (T_2 - 75)/T_1\\\\2 - 1 = 2T_2/T_1 - (T_2 - 75)/T_1\\\\ = (T_2 + 75)/T_1T_1 = T_2 + 75\\\Now\ we\ will\ Put\ the\ values\ into\ equation (1)\\\\1/6 = 1 - T_2/(T_2 + 75)\\\\1/6 = (75)/(T_2 + 75)[/tex]

T_2 + 450 = 75

T_2 = 375

Now put the T_2 value in any of the above equation

i.e

T_1 = T_2 + 75

T_1 = 375 + 75

= 450

Answer:

The test charge will take the south-west direction indicated in option 6.

Explanation:

The image is shown below.

Since all the charges are positively charged, they will all repel each other. If we consider the force on +q due to +Q and +Q, then we can proceed as follows

The +Q particle at the top left corner of the cube will exert a vertical downward force on +q in the -ve y-axis.

The +Q particle at the bottom right corner of the cube will exert a force on +q towards the horizontal left on the -ve x-axis.

Both of these forces will act at angle of 90°, and therefore, the resultant force will act at an angle of 45° to horizontal and vertical forces.

The result is that the +q charge will move in a south-west direction of the cube.

Explanation:

As per Rayleigh criterion, the angular resolution is given as follows:

[tex]\theta=\frac{1.22 \lambda}{D}[/tex]

From this expression larger the size of aperture, smaller will be the value of angular resolution and hence, better will be the device i.e. precision for distinguishing two points at very high angular difference is higher.

Answer:

P= 2414.9 Pa

Explanation:

given

density of air , p = 1.29 kg/m³

speed of air over the upper surface , v₁ = 125 m/s

speed of air over the lower surface , v₂ = 109 m/s

the pressure difference on an airplane wing , P = 0.5 × p × ( v₁² - v₂²)

P = 0.5 × 1.29 × ( 125² - 109²)

P= 0.645(3744)

P = 2414.9 Pa

the pressure difference on an airplane wing is 2414.9 Pa

. . . is carrying more energy than a wave in the same medium with a lower amplitude.

Answer: the direction of the magnetic force on the electron will be moving out of the screen, perpendicular to the magnetic field.

Explanation:

The magnetic force F on a moving electron at right angle to a magnetic field is given by the formula:

F = BqVSinØ

If an electron moves in the plane of this screen toward the top of the screen. A magnetic field is also in the plane of the screen and directed toward the right. Then, the direction of the magnetic force on the electron will be perpendicular to the magnetic field

According to the Fleming's left - hand rule, the direction of the magnetic force on the electron will be moving out of the plane of the screen.

Answer:

the angular momentum is 1015.52 kg m²/s

Explanation:

given data

mass of each flywheel, m = 65 kg

radius of flywheel, r = 1.47 m

ω1 = 8.94 rad/s

ω2 = - 3.42 rad/s

to find out

magnitude of the net angular momentum

solution

we get here Moment of inertia that is express as

I = 0.5 m r²    .................1

put here value and we get

I = 0.5 × 65 × 1.47 × 1.47

I = 70.23 kg m²

and

now we get here Angular momentum that is express as

L = I × ω    ...........................2

and Net angular momentum will be

L = 2 × I x ω1 - I × ω2

put here value and we get

L = 2 × 70.23 × 8.94 - 70.23 × 3.42

L = 1015.52 kg m²/s

so

the angular momentum is 1015.52 kg m²/s

The magnitude of the net angular momentum of the system will be "1015.52 kg.m²/s".

According to the question,

Flywheel's mass, m = 65 kg

Flywheel's radius, r = 1.47 m

ω₁ = 8.94 rad/s

ω₂ = 3.42 rad/s

We know,

The moment of inertia (I),

= 0.5 m r²

By substituting the values,

= 0.5 × 65 × 1.47 × 1.47

= 70.23 kg.m²

hence, The angular momentum be:

→ L = I × ω or,

     = 2 × I × ω₁ - l × ω₂

     = 2 × 70.23 × 8.94 - 70.23 × 3.42

     = 1015.52 kg.m²/s

Thus the above answer is correct.

Find out more information about momentum here:

https://brainly.com/question/25121535

Answer:

Due to flipping of polarity

Explanation:

During the changing of polarity, the current on the one side is maximum as the polarity change then the current is gradually reducing toget from another end.

Explanation:

A projectile is usually launched by an initial force, is influenced by gravity forces and air resistance, and takes a parabolic, or more accurately, an  elliptical path. At the beginning of the launch of a rocket, the rocket is mostly under the effect of its engine thrust, and takes a vertical flight path upwards; using engine thrust to maneuver itself to remain in this vertical flight till it is almost at its required orbit. At this stage, the rocket can't be said to follow a projectile path. When the rocket gets to the pitchover stage, at which it is almost ready to enter its atmosphere, the engine thrust is maneuvered to turn the rocket by an angle of attack. At this stage, the flight path is no longer vertical. At this point after pitchover, in which the flight path is no longer vertical, gravity tends to pull the rocket down in a parabolic path. This is the point where the rocket acts as a projectile, but is countered by engine thrust.

Answer:

E= 71dB

Explanation:

See attached file for step by step calculation

Explanation:

Ohms law states that the electrical current present in a metallic conductor is directly proportional to the potential difference between the metallic conductor and inversely proportional to the resistance therefore if the voltage is increased resistance also increases provided that temperature and other physical properties remains constant V=IR

Answer:

Surface tension is the tendency of liquid surfaces to shrink into the minimum surface area possible. Surface tension allows insects (e.g. water striders), usually denser than water, to float and slide on a water surface.

Explanation:

Answer:

It is the tension of the surface film of a liquid caused by the attraction of the particles in the surface layer by the bulk of the liquid, which tends to minimize surface area.

Answer:

Final pressure 0.105atm

Explanation:

Let V1 represent the initial volume of dry air at NTP.

under adiabatic condition: no heat is lost or  gained by the system. This does not implies that the constant temperature throughout the system , but rather that no heat gained or loss by the system.

Adiabatic expansion:

[tex]\frac{T_1}{T_2} =(\frac{V_1}{V_2} )^{\gamma -1}[/tex]

273/T2=(5V1/V1)^(1.4−1)

273/T2=5^0.4

Final temperature  T2=143.41 K

Also

P1/P2=(V2/V1)^γ

1/P2=(5V1/V1)^1.4

Final pressure P2=0.105atm