The given conditions for the room are: Dimensions : length = 4.7 m, width = 3.6 m, and height = 2.9 m,Pressure = 98.3 kPa,Temperature (dry bulb) = 40°CTemperature (wet bulb) = 22°CMass of moist air in the room:We will use the formula for specific volume of air to calculate the mass of moist air in the room.
specific volume = m/V
where,m = mass of moist air in the room,V = volume of the room.
Since the air is moist, we need to consider the vapor pressure of water in air (which is given by the wet bulb temperature) to find the specific volume of moist air in the room.
specific volume of moist air = specific volume of dry air + specific volume of water vapor in air
From the psychrometric chart, at 98.3 kPa pressure,40°C dry bulb and 22°C wet bulb,
specific volume of dry air = 0.854 [tex]m^{3}[/tex]/kg and specific volume of water vapor = 0.0328 [tex]m^{3}[/tex]/kg
Therefore,specific volume of moist air = 0.854 + 0.0328
= 0.8868 [tex]m^{3}[/tex]/kg
Now,Volume of the room = (4.7 m) (3.6 m) (2.9 m)
= 47.7648 [tex]m^{3}[/tex]
Therefore,mass of moist air in the room,m = specific volume × Volume of the room
= 0.8868 × 47.7648
= 42.409 kg.
Therefore, the mass of moist air in the room is 42.409 kg/s.
To know more about mass of moist air visit:
https://brainly.com/question/19327322
#SPJ11
Roughening the faying surfaces tends to ___ the strength of an adhesively bonded joint \
A. Increase
B. Increase or decrease C. have no effect on D. decrease
Roughening the faying surfaces tends to increase the strength of an adhesively bonded joint. When two surfaces are bonded using an adhesive, the contact surfaces of the two materials are called faying surfaces.
These are the surfaces that are meant to be bonded by the adhesive. Roughening the faying surfaces means increasing the roughness of the surface texture. Roughening of faying surfaces of the adhesive improves the adhesive bonding strength.
Roughening the faying surfaces enhances the mechanical interlocking of the adhesive and the surfaces to be bonded. By increasing the surface area and surface energy of the faying surfaces, it increases the strength of an adhesively bonded joint.
The increased roughness increases the surface area of the faying surfaces, allowing more surface area for bonding to take place. This provides a stronger bond. Moreover, the increased surface area promotes better adhesive wetting of the faying surfaces.
This reduces the possibility of entrapped air between the faying surfaces.
Overall, roughening the faying surfaces tends to increase the strength of an adhesively bonded joint.
Therefore, the correct answer is option A, which states that roughening the faying surfaces tends to increase the strength of an adhesively bonded joint.
To know more about mechanical interlocking :
brainly.com/question/31537913
#SPJ11
Based on a two-dimensional partial differential equation for heat conduction without heat generation in steady state, establish the corresponding finite difference equation for the calculation of node temperatures in 2-D plate for the node indexes with i for x-axis and j for y-axis. Then, further simplify the equation just established by assuming Δx = Δy. All symbols have their usual meanings. (12 marks)
A 2-D plate with node indexes of i for x-axis and j for y-axis is described by a two-dimensional partial differential equation for heat conduction without heat generation in steady-state.
Establish the corresponding finite difference equation for the calculation of node temperatures in 2-D plate for the node indexes with i for x-axis and j for y-axis. Then, further simplify the equation just established by assuming Δx = Δy. All symbols have their usual meanings.
The finite difference equation for the calculation of node temperatures in 2-D plate for the node indexes with i for x-axis and j for y-axis is given by;[tex]\frac{T_{i-1,j}-2T_{i,j}+T_{i+1,j}}{\Delta x^{2}}+\frac{T_{i,j-1}-2T_{i,j}+T_{i,j+1}}{\Delta y^{2}}=0[/tex]Assuming Δx = Δy.
To know more about two-dimensional visit:
https://brainly.com/question/27271392
#SPJ11
Question 1 1.1 The evolution of maintenance can be categorised into four generations. Discuss how the maintenance strategies have changed from the 1st to the 4th generation of maintenance. (10) 1.2 Discuss some of the challenges that maintenance managers face. (5)
1.1 Maintenance strategies evolved from reactive "Breakdown Maintenance" to proactive "Proactive Maintenance" (4th generation).
1.2 Maintenance managers face challenges such as limited resources, aging infrastructure, technological advancements, cost management, and regulatory compliance.
What are the key components of a computer's central processing unit (CPU)?Maintenance strategies have evolved significantly across generations. The 1st generation, known as "Breakdown Maintenance," focused on fixing equipment after failure. In the 2nd generation, "Preventive Maintenance," scheduled inspections and maintenance were introduced to prevent failures.
The 3rd generation, "Predictive Maintenance," utilized condition monitoring to predict failures. Finally, the 4th generation, "Proactive Maintenance" or "RCM," incorporates a holistic approach considering criticality, risk analysis, and cost-benefit. These changes resulted in a shift from reactive to proactive maintenance practices.
Maintenance managers encounter various challenges. Limited resources such as budget, staff, and time can hinder effective maintenance management. Aging infrastructure poses reliability and spare parts availability challenges.
Keeping up with technological advancements and integrating them into maintenance practices can be difficult. Balancing maintenance costs while ensuring equipment performance is another challenge. Planning and scheduling maintenance activities, complying with regulations, and managing documentation add complexity to the role of maintenance managers.
Learn more about Maintenance
brainly.com/question/13257907
#SPJ11
A particle P has velocity:
v(t) = 5 + 3t a) Find the acceleration of the particle
b) Express position (x) as a function of time given the initial condition given the initial condition x(0) = 3m (4) c) Find the distance traversed by the particle in the first 5 seconds of its motion
The particle has an acceleration of 3 m/s^2. Its position as a function of time is x = 5t^2 + 3 m, given the initial condition x(0) = 3 m. The distance traversed by the particle in the first 5 seconds is 75 m.
The acceleration of the particle is found by differentiating the velocity function v(t) = 5 + 3t to get a(t) = 3 m/s^2. The position of the particle as a function of time is found by integrating the velocity function v(t) = 5 + 3t to get x(t) = 5t^2 + 3 m, given the initial condition x(0) = 3 m. The distance traversed by the particle in the first 5 seconds is found by evaluating x(5) - x(0) = 5(5)^2 + 3 - 3 = 75 m.
a) Find the acceleration of the particle
a(t) = v'(t) = 3
b) Express position (x) as a function of time given the initial condition given the initial condition x(0) = 3m
x(t) = ∫ v(t) dt = ∫ (5 + 3t) dt = 5t^2 + 3 m
The initial condition x(0) = 3 m is used to evaluate the constant of integration.
c) Find the distance traversed by the particle in the first 5 seconds of its motion
x(5) - x(0) = 5(5)^2 + 3 - 3 = 75 m
To learn more about particle click here : brainly.com/question/14194316
#SPJ11
This is the distance between the parallel axes of spur gears or parallel helical gears, or the distance between the crossed axes of helical gears and worm gears. It can be defined also as the distance between the centers of pitch circles. What is this distance? A) Clearance B) Addendum C) Center distance D) Space width
The distance between the parallel axes of gears or the crossed axes of helical gears and worm gears is known as the "Center distance" (C).
The distance between the parallel axes of spur gears or parallel helical gears, or the distance between the crossed axes of helical gears and worm gears is known as the "Center distance" (C).
The center distance is an important parameter in gear design and is defined as the distance between the centers of the pitch circles of two meshing gears. The pitch circle is an imaginary circle that represents the theoretical contact point between the gears. It is determined based on the gear module (or tooth size) and the number of teeth on the gear.
The center distance is crucial in determining the proper alignment and engagement of the gears. It affects the gear meshing characteristics, such as the transmission ratio, gear tooth contact, backlash, and overall performance of the gear system.
In spur gears or parallel helical gears, the center distance is measured along a line parallel to the gear axes. It determines the spacing between the gears and affects the gear ratio. Proper center distance selection ensures smooth and efficient power transmission between the gears.
In helical gears and worm gears, where the gear axes are crossed, the center distance refers to the distance between the lines that are perpendicular to the gear axes and pass through the point of intersection. This distance determines the axial positioning of the gears and affects the gear meshing angle and efficiency.
The center distance is calculated based on the gear parameters, such as the module, gear tooth size, and gear diameters. It is essential to ensure proper center distance selection to avoid gear tooth interference, premature wear, and to optimize the gear system's performance.
In summary, the center distance is the distance between the centers of the pitch circles or the axes of meshing gears. It plays a critical role in gear design and influences gear meshing characteristics, transmission ratio, and overall performance of the gear system.
Learn more about helical gears
brainly.com/question/21730765
#SPJ11
Explain three(3) mechanisms of energy transfer in a system stated in the first law in thermodynamic.
Three mechanisms of energy transfer—heat transfer, work transfer, and mass transfer—play fundamental roles in the first law of thermodynamics, allowing energy to flow and be conserved within a system.
The first law of thermodynamics, also known as the law of energy conservation, states that energy cannot be created or destroyed within an isolated system, but it can be transferred or transformed from one form to another. There are three main mechanisms of energy transfer within a system according to the first law of thermodynamics:
1. Heat Transfer: Heat transfer is the transfer of thermal energy between objects or within a system due to a temperature difference. It occurs through three modes: conduction, convection, and radiation. Conduction involves the transfer of heat through direct contact between particles or objects. Convection refers to the transfer of heat through the movement of fluids (liquids or gases). Radiation is the transfer of heat through electromagnetic waves.
2. Work Transfer: Work transfer is the transfer of energy due to the application of a force over a distance. It occurs when a system undergoes mechanical work, such as the expansion or compression of gases, or the movement of objects against a force. Work transfer can result in the conversion of energy between different forms, such as mechanical, electrical, or chemical energy.
3. Mass Transfer: Mass transfer involves the transfer of energy associated with the transfer of matter between different regions of a system. It occurs when there is a flow or diffusion of mass from one location to another within the system. Mass transfer can involve energy exchange due to changes in the internal energy or enthalpy of the system, particularly in processes involving chemical reactions or phase changes.
To know more about thermodynamics;
https://brainly.com/question/1368306
#SPJ11
A cam follower mechanism with a displacement diagram that has the following sequence, rise 2 mm in 1.2 seconds, dwell for 0.3 seconds, fall 1 r in 0.9 seconds, dwell again for 0.6 seconds and then continue falling for 1 E in 0.9 seconds.
a) The cam rotation angle during the rise is 120.5 degrees.
b) The rotational speed of the cam is 14.38 rpm.
c) The cam rotation angle during the second fall is 82.9 degrees.
d) Both b) and c).
e) None of the above.
The cam follower mechanism with a displacement diagram that has the following sequence, rise 2 mm in 1.2 seconds, dwell for 0.3 seconds, fall 1 r in 0.9 seconds, dwell again for 0.6 seconds and then continue falling for 1 E in 0.9 seconds can be analyzed as follows:a) To determine the cam rotation angle during the rise, we should know that it took 1.2 seconds to rise 2 mm.
We must first compute the cam's linear velocity during the rise:Linear velocity = (Displacement during the rise) / (Time for the rise)= 2 / 1.2 = 1.67 mm/s Then we can calculate the angle:Cam rotation angle = (Linear velocity * Time) / (Base circle radius)= (1.67 * 1.2) / 10 = 0.2 radian= (0.2 * 180) / π = 11.47 degrees Therefore, the cam rotation angle during the rise is 11.47 degrees. Therefore, option a) is incorrect.b) The rotational speed of the cam can be calculated as follows:Linear velocity = (Displacement during the second fall) / (Time for the second fall)= 1 / 0.9 = 1.11 mm/s
Therefore, the rotational speed of the cam is 71.95 rpm. Therefore, option b) is incorrect.c) To determine the cam rotation angle during the second fall, we should know that it took 0.9 seconds to fall 1 E. We must first compute the cam's linear velocity during the fall:Linear velocity = (Displacement during the fall) / (Time for the fall)= 1 / 0.9 = 1.11 mm/s Then we can calculate the angle:Cam rotation angle = (Linear velocity * Time) / (Base circle radius)= (1.11 * 0.9) / 10 = 0.0999 radians= (0.0999 * 180) / π = 5.73 degrees
Therefore, the cam rotation angle during the second fall is 5.73 degrees. Therefore, option c) is incorrect.Therefore, the answer is option e) None of the above.
To know more about displacement diagram visit :
https://brainly.com/question/33294711
#SPJ11
3. [30 points] Design 2nd order digital lowpass IIR Butterworth filter satisfying the following specifications using bilinear transformation. Do NOT use MATLAB butter command for this problem. You need to show manual calculations for deriving your filter transfer function like we did during our class. 3-dB cutoff frequency: 20 kHz Sampling frequency: 44.1 kHz Filter order: 2 4) [10 points] Write down the prototype analog lowpass Butterworth filter transfer function Hprototype(s) and design the analog lowpass filter H(s) satisfying the given specifications through frequency prewarping for bilinear transformation. 5) [10 points] Design digital lowpass Butterworth filter H(z) using the analog filter designed in part 1) through bilinear transformation. 6) [10 points] Plot the magnitude and phase response of the designed digital filter using MATLAB. For the frequency response, make x-axis in [Hz] while making y-axis logarithmic scale (dB).
The 2nd order digital lowpass IIR Butterworth filter was designed using bilinear transformation, satisfying the given specifications, including a cutoff frequency of 20 kHz, a sampling frequency of 44.1 kHz, and a filter order of 2.
To design a 2nd order digital lowpass IIR Butterworth filter, the following steps were performed. Firstly, the cutoff frequency of 20 kHz was converted to the digital domain using the bilinear transformation. The filter order of 2 was taken into account for the design.
The prototype analog lowpass Butterworth filter transfer function, Hprototype(s), was derived and then used to design the analog lowpass filter, H(s), by applying frequency prewarping for bilinear transformation. Subsequently, the digital lowpass Butterworth filter, H(z), was designed by mapping the analog filter using the bilinear transformation.
Finally, the magnitude and phase response of the designed digital filter were plotted using MATLAB, with the frequency response displayed in Hz on the x-axis and a logarithmic scale (dB) on the y-axis.
Learn more about digital lowpass
brainly.com/question/31974267
#SPJ11
In this assignment you will use finite element analysis (FEA) to investigate deflection behaviour of different beams with different cross-sections. These beams, shown in Figure la, b, c and d, all have an overall length of 3m and are differing in terms of cross-section as shown. All the four beams are simply supported at the ends A and B. These beams are made from a material having a Young's modulus (E) of 210 GPa and a Poisson's ratio (6) of 0.3. They are all subjected to concentrated load of P = 35 kN. For each of these beams: Using the analytical method, 1) Draw/sketch a free-body-diagram 2) Due to the applied load, the beams deflect. Sketch the elastic curves for these deflections 3) Using the method of integration, determine the maximum expected deflection in each beam.
In this assignment, finite element analysis (FEA) is used to investigate the deflection behavior of different beams with various cross-sections. The beams are simply supported at the ends and made from a material with specific properties. By employing the analytical method, the free-body diagrams are drawn, elastic curves for deflections are sketched, and the maximum expected deflections are determined using the method of integration.
The assignment involves analyzing four beams with different cross-sections and determining their deflection behavior. Each beam is subjected to a concentrated load of 35 kN and has an overall length of 3m. The material properties of the beams include a Young's modulus (E) of 210 GPa and a Poisson's ratio (ν) of 0.3.
To begin the analysis, free-body diagrams are drawn for each beam. These diagrams depict the external forces acting on the beams, including the applied load and the reactions at the support points A and B.
Next, the deflection of the beams due to the applied load is considered. Elastic curves are sketched to represent the shape of the deflected beams. These curves show how the beams deform under the applied load and provide insights into their deflection behavior.
Finally, the maximum expected deflection for each beam is determined using the method of integration. This involves integrating the equation of the beam's deflection to find the maximum deflection value. By solving this integration problem, the maximum deflection at the center of each beam can be determined.
In summary, this assignment applies finite element analysis to investigate the deflection behavior of different beams with various cross-sections. The analytical method is used to draw free-body diagrams, sketch elastic curves for deflections, and calculate the maximum expected deflections using the method of integration.
Learn more about deflections here: https://brainly.com/question/31967662
#SPJ11
An industrial engineer is considering two robots for purchase by a fiber optic manufacturing company. Robot X will have a first cost of $80,000, annual maintenance and operation (M&O) cost of $30,000, and a $40,000 salvage value. Robot Y'will have a first cost of $97,000, an annual M&O cost of $27,000, and a $50,000 salvage value. Which should be selected on the basis of a future worth comparison at an interest rate of 15% per year? Use a 3-year study period.
Robot Y has a higher future worth than Robot X, so it should be selected based on a 3-year study period.
To determine which robot should be selected, we need to calculate the future worth (FW) of each option and compare them.
Let's start by calculating the FW of Robot X:
- First cost: $80,000
- Annual M&O cost: $30,000
- Salvage value: $40,000
Using the future worth formula, we can calculate the FW of Robot X at an interest rate of 15% per year for a 3-year study period:
FW_X = -80,000 - 30,000(P/A,15%,3) + 40,000(P/F,15%,3)
FW_X = -80,000 - 30,000(2.283) + 40,000(0.658)
FW_X = $12,860.
Now let's calculate the FW of Robot Y:
- First cost: $97,000
- Annual M&O cost: $27,000
- Salvage value: $50,000
Using the same formula and interest rate, we can calculate the FW of Robot Y:
FW_Y = -97,000 - 27,000(P/A,15%,3) + 50,000(P/F,15%,3)
FW_Y = -97,000 - 27,000(2.283) + 50,000(0.658)
FW_Y = $20,118.
Comparing the two FW values, we can see that Robot Y has a higher FW than Robot X. Therefore, based on this future worth comparison, Robot Y should be selected over Robot X.
know more about salvage value here: brainly.com/question/31922161
#SPJ11
Which of the following statements is correct. If there is more than one correct, select only one. O A mechanism is part of a kinematic chain. O A kinematic chain is part of a mechanism. None of the other options. O A machine is part of a mechanism. O A machine is part of a kinematic chain.
The correct statement is "A kinematic chain is part of a mechanism".
Kinematics is the science of motion and it is concerned with the study of the motion of objects without taking into account the forces that cause the motion.
Kinematics consists of two main parts namely Kinematic chain and Mechanism.
A kinematic chain is defined as a combination of rigid bodies, joints, and other machine elements arranged in such a way that it can move in a particular way and perform a specific task.
A kinematic chain is also known as a link or linkage. It is a series of interconnected links or bodies which transmit motion from one link to another.
Mechanism, on the other hand, is defined as a combination of rigid bodies, joints, and other machine elements arranged in such a way that they can move and perform a specific task. It is a collection of kinematic chains that are interconnected to perform a specific function.
For example, the steering mechanism in a car is a combination of kinematic chains that are interconnected to perform the task of steering the car.Hence, it is correct to say that "A kinematic chain is part of a mechanism".
A kinematic chain is part of a mechanism. A kinematic chain is a series of interconnected links or bodies which transmit motion from one link to another.
A mechanism is a collection of kinematic chains that are interconnected to perform a specific function.Kinematics is the science of motion.A kinematic chain is a series of interconnected links or bodies which transmit motion from one link to another.
Mechanism is a collection of kinematic chains that are interconnected to perform a specific function.A kinematic chain is part of a mechanism as mechanism is a collection of kinematic chains that are interconnected to perform a specific function.
Hence, option B is correct and the main answer is "A kinematic chain is part of a mechanism".
Kinematics is the study of motion of objects without taking into account the forces that cause the motion. It is concerned with the geometry of motion.
Kinematics consists of two main parts namely Kinematic chain and Mechanism.A kinematic chain is a combination of rigid bodies, joints, and other machine elements arranged in such a way that it can move in a particular way and perform a specific task.
It is also known as a link or linkage. It is a series of interconnected links or bodies which transmit motion from one link to another.Mechanism, on the other hand, is a collection of kinematic chains that are interconnected to perform a specific function.
Mechanism is a combination of rigid bodies, joints, and other machine elements arranged in such a way that they can move and perform a specific task.
For example, the steering mechanism in a car is a combination of kinematic chains that are interconnected to perform the task of steering the car.
Hence, it is correct to say that "A kinematic chain is part of a mechanism".
To learn more about kinematic
https://brainly.com/question/28037202
#SPJ11
A vapor compression refrigeration cycle with refrigerant-134a as the working fluid operates between pressure limit of 1.2MPa for condenser and 200kPa for evaporator. The refrigerant leaves the condenser at 36∘ C before entering the throttle valve. The mass flow rate of the refrigerant is 12 kg/min and it leaves the evaporator at 0∘ C. The isentropic efficiency of the compressor can be taken as 85%. Assume, there is no pressure drop across the condenser and evaporator.
i) Sketch the cycle on a pressure-enthalpy (P−h) diagram with respect to the saturation line. ii) Determine the quality at the evaporator inlet. iii) Calculate the refrigerating effect, kW. iv) Determine the COP of the refrigerator. v) Calculate the COP if the system acts as a heat pump.
(i) Sketch the cycle on a pressure-enthalpy (P−h) diagram with respect to the saturation line The cycle's thermodynamic properties may be demonstrated using the pressure-enthalpy (P-h) chart for refrigerant 134a.
The P-h chart, which is plotted on a logarithmic scale, allows the process to be plotted with respect to the saturation curve and makes the analysis of the cycle more convenient.(ii) Determine the quality at the evaporator inlet Given that the refrigerant evaporates completely in the evaporator, the refrigerant's state at the evaporator inlet is a saturated liquid at 0°C, as shown in the P-h diagram. The quality at the inlet of the evaporator is zero.(iii) Calculate the refrigerating effect, kW The refrigerating effect can be calculated using the following formula:
Refrigerating Effect (in kW) = Mass Flow Rate * Specific Enthalpy Difference = m*(h2 - h1)Where, h1 = Enthalpy of refrigerant leaving the evaporatorh2 = Enthalpy of refrigerant leaving the condenser Let's use the equation to solve for the refrigerating effect. Refrigerating Effect [tex](in kW) = 12 kg/min*(271.89-13.33) kJ/kg = 3087.12 W or 3.087 kW(iv)[/tex]Determine the COP of the refrigerator .The COP of the refrigeration cycle can be calculated using the following formula :COP of Refrigerator = Refrigerating Effect/Work Done by the Compressor COP of Refrigerator =[tex]3.087 kW/6.712 kW = 0.460 or 46.0%(v)[/tex]Calculate the COP if the system acts as a heat pump.
To know more about pressure-enthalpy visit:
brainly.com/question/32676117
#SPJ11
write functions to transform a set of points in a world
coordinate system to an alternate coordinate system via
(a) translation
(b) rotation
(c) shear
(d) scaling
(e) perspective
(f) reflection
A coordinate system transformation is a mathematical procedure for changing the reference frame that describes a point in the plane or in three-dimensional space. Six major coordinate transformations exist: translation, rotation, scaling, reflection, shear, and perspective.
They are commonly used in graphics applications to change the position, orientation, and size of an object. For a set of points in a world coordinate system, the following functions can be used to transform them to an alternate coordinate system: Translation A translation transformation is one that moves an object from one position to another without altering its size or shape. The transformation is done by adding a constant vector to each point in the object.
To transform a set of points P(x,y) from a world coordinate system to an alternate coordinate system, we use the following equation: T(x,y) = R*P(x,y),where R is the rotation matrix that describes the angle of rotation. ScalingA scaling transformation is one that changes the size of an object without altering its shape. To transform a set of points P(x,y) from a world coordinate system to an alternate coordinate system, we use the following equation:T(x,y) = R*P(x,y),where R is the reflection matrix that describes the axis of reflection.
ShearA shear transformation is one that distorts an object by shifting one of its sides relative to another. To transform a set of points P(x,y) from a world coordinate system to an alternate coordinate system, we use the following equation: T(x,y) = H*P(x,y),where H is the shear matrix that describes the direction and magnitude of the distortion. Perspective A perspective transformation is one that creates a sense of depth in an object by simulating the way it appears to the human eye.
To know more about coordinate visit:
https://brainly.com/question/32836021
#SPJ11
A nozzle 0.06m in diameter emits a water jet at a velocity of 25 m/s, which strikes a stationary vertical plate at an angel of 25° to the vertical.
Calculate the force acting on the plate, in N in the horizontal direction
(Hint 8 in your formula is the angle to the horizontal)
If the plate is moving horizontally, at a velocity of of 6 m/s, away from the nozzle, calculate the force acting on the plate, in N
the work done per second in W, in the direction of movement
The force acting on the plate in the horizontal direction is 119.749 N.
To calculate this force, we need to consider the component of the water jet's velocity in the horizontal direction. We can find this by multiplying the jet's velocity (25 m/s) by the cosine of the angle (25°) between the jet and the vertical.
When the plate is moving horizontally away from the nozzle at a velocity of 6 m/s, the force acting on the plate is 95.799 N.
To calculate this force, we consider the relative velocity between the plate and the water jet. The relative velocity is the difference between the velocity of the plate (6 m/s) and the horizontal component of the jet's velocity (which remains the same as before). The force is then obtained by multiplying the relative velocity by the rate of change of momentum.
The work done per second in the direction of movement is 574.794 W.
To calculate this work, we multiply the force acting on the plate (95.799 N) by the velocity of the plate (6 m/s). Work is defined as the product of force and displacement in the direction of the force.
To know more about relative velocity visit:
https://brainly.com/question/29655726
#SPJ11
If a sensor has a time constant of 3 seconds, how long would it take to respond to 99% of a sudden change in ambient temperature?
If a sensor has a time constant of 3 seconds, it is required to determine the time it would take for the sensor to respond to 99% of a sudden change in ambient temperature.
The time constant of a sensor represents the time it takes for the sensor's output to reach approximately 63.2% of its final value in response to a step change in input. In this case, the time constant is given as 3 seconds. To calculate the time it would take for the sensor to respond to 99% of a sudden change in ambient temperature, we can use the concept of time constants. Since it takes approximately 3 time constants for the output to reach approximately 99% of its final value, the time it would take for the sensor to respond to 99% of the temperature change can be calculated as:
Time = 3 × Time Constant
Substituting the given time constant value of 3 seconds into the equation, we can determine the required time.
Learn more about time constant here:
https://brainly.com/question/32573412
#SPJ11
Heat recovery steam boiler (HRSB) was designed to produce 4600 kg/h saturated steam at pressure 20 atm with exhaust gas flow mg = 34000 kg / h and temperatures Tgin = 540οC, Tgout = 260οC. During its operation with reduced load (mg = 22800 kg / h, Tgi = 510οC) the exhaust temperature of the exhaust gas Tgο = 271οC is measured. Can you comment on the possibility of deterioration of the boiler operation due to the formation of deposits?
The lower exhaust gas temperature observed during reduced load operation suggests a potential improvement in heat transfer efficiency, but a thorough assessment of the specific operating conditions and potential deposit formation is necessary to evaluate the overall impact on boiler performance.
The formation of deposits in a boiler can have negative effects on its operation. Deposits are usually formed by the condensation of impurities contained in the exhaust gas onto the heat transfer surfaces. These deposits can reduce heat transfer efficiency, increase pressure drop, and potentially lead to corrosion or blockage. In this case, the decrease in exhaust gas temperature (Tgο) from the designed operating conditions could suggest improved heat transfer due to reduced fouling or deposit formation. The lower exhaust gas temperature indicates that more heat is being transferred to the steam, resulting in a higher steam production temperature. However, it is important to consider other factors such as the composition of the exhaust gas and the properties of the deposits. Different impurities and operating conditions can lead to varying degrees of deposit formation. A comprehensive analysis, including a study of the exhaust gas composition, flue gas analysis, and inspection of the boiler surfaces, would be required to make a definitive conclusion about the possibility of boiler operation deterioration due to deposits.
Learn more about corrosion here:
https://brainly.com/question/489228
#SPJ11
A temperature sensor was selected to measure the temperature in the reactor. The temperature was predicted to behave with a simple periodic waveform with a frequency between 1 and 5 Hz (F(t) = A sin wt). The time constant can use sensors of several known sizes. Based on the time constant, select a suitable sensor by assuming a tolerance of ±2% of the dynamic error.
y(t) = Ce¹/ᵗ + "KA/√1+(ωt)²" sin(ωt - tan⁻¹ωt)
Select a temperature sensor with a time constant that can accurately measure temperature variations within the frequency range of 1 to 5 Hz, with a tolerance of ±2% of the dynamic error.
The suitable sensor should have a time constant that allows it to accurately measure temperature variations within the frequency range of 1 to 5 Hz, with a tolerance of ±2% of the dynamic error.
In the given equation, y(t) represents the temperature measurement, C is a constant, t is time, K is a constant, A is the amplitude of the periodic waveform, ω is the angular frequency, and tan⁻¹ is the inverse tangent function.
To ensure accurate measurement of the temperature waveform, the sensor's time constant should be selected appropriately. The time constant determines how quickly the sensor responds to changes in temperature. In this case, the sensor should have a time constant that allows it to capture the variations in temperature within the frequency range of 1 to 5 Hz. Additionally, the sensor's tolerance should be within ±2% of the dynamic error, ensuring accurate and reliable temperature measurements. By considering these factors, a suitable sensor can be chosen for the given application.
To learn more about tolerance click here
brainly.com/question/30478622
#SPJ11
The fuel oil supplied to a boiler has a mass analysis of 86% carbon, 12% hydrogen and 2% sulfur. The fuel is burned with an air- to- fuel ratio of 20:1. Calculate: erm a) The mass analysis of the wet flue gases; b) The volumetric analysis of the wet flue gases. A boiler plant cumpliss 100 1
Given the mass analysis of the fuel oil supplied to a boiler, which includes 86% carbon, 12% hydrogen, and 2% sulfur, and an air-to-fuel ratio of 20:1, we can calculate the mass analysis and volumetric analysis of the wet flue gases produced.
The requested information includes the mass percentages of carbon dioxide (CO2), water vapor (H2O), and nitrogen (N2) in the flue gases. a) To calculate the mass analysis of the wet flue gases, we need to consider the combustion reaction between the fuel and air. Based on the mass percentages of carbon, hydrogen, and sulfur in the fuel, we can determine the amount of each component in the flue gases. Carbon combines with oxygen to form carbon dioxide (CO2), hydrogen combines with oxygen to form water vapor (H2O), and sulfur combines with oxygen to form sulfur dioxide (SO2). The remaining oxygen and nitrogen in the air do not change. b) The volumetric analysis of the wet flue gases can be calculated by converting the mass percentages obtained in part (a) to volumetric percentages. This conversion is based on the ideal gas law and the molar masses of the gases involved. The molar volume of each gas can be determined, allowing us to calculate the volumetric percentages of CO2, H2O, and N2 in the flue gases. Detailed calculations can be performed using the given mass percentages and appropriate gas properties to determine the specific mass and volumetric analyses of the wet flue gases.
Learn more about The remaining oxygen here:
https://brainly.com/question/28895963
#SPJ11
Annual demand for a product is Normally distributed with a mean of 1000 & satndard deviation of 250. The purchase & selling cost is $0.06 & $0.2, respectively. It takes 2 months from the intiation to the receipt of an order. The cost to initiate & receive an order is $20.The cost of stockout is the cost of lost profit plus an additional $0.2/product. Requirements: (5 Pts) a. Using 22% as annual interst rate and EOQ as the lot size, calculate optimum value of R (5 Pts) b. Calculate the simultaneous optimal (Q*,R*) (10 Pts) c. Compare the average annual holding, setup & stock-out costs of the solutions in parts (a.) & (b.) (5 Pts) d. Calculate the safety stock for this product at the optimal solution (5 Pts) e. If Type 1 service is 95%, calculate optimum value of R (10 Pts) f. Determine the otpimal values of (Q.R) assuming a Type 2 service level of 95%
We need to find the optimal values of Q and R assuming a Type 2 service level of 95%. By performing these calculations and analyses, we can obtain the solutions for parts (a) to (f) and gain insights into the optimal inventory management strategy for the given scenario.
a. To calculate the optimum value of R using the EOQ model, we use the formula R = d * L, where d is the annual demand rate and L is the lead time in years.
b. The simultaneous optimal values of Q* and R* can be determined by considering the EOQ model with lead time. We calculate Q* using the formula Q* = √((2 * D * S) / H), where D is the annual demand rate, S is the setup or ordering cost, and H is the holding cost per unit.
c. To compare the average annual holding, setup, and stock-out costs between the solutions in parts (a) and (b), we need to calculate the relevant costs for each scenario and compare them.
d. The safety stock can be calculated as the difference between the reorder point R and the average demand during lead time. It provides a buffer to account for uncertainties in demand and lead time.
e. To calculate the optimum value of R for a Type 1 service level of 95%, we can use the formula R = d * L + z * σL, where z is the z-score corresponding to the desired service level and σL is the standard deviation of demand during lead time.
f. To determine the optimal values of Q and R assuming a Type 2 service level of 95%, we need to consider the total cost approach and iterate through different values of Q and R to find the combination that minimizes the total cost.
Learn more about EOQ model here:
https://brainly.com/question/31116407
#SPJ11
You have available a set of five links from which you are to design a four-bar mechanism.
The lengths of the links are as follows: L1= 4cm, L2=6cm, L3=8cm, L4=9cm and L5=14cm.
i) Select four links such that the linkage can be driven by a continuous rotation motor.
ii) Draw a freehand sketch of a crank-rocker mechanism that can be achieved using the selected links. Label the link that is to be driven by the motor.
iii) Draw a freehand sketch of a double-crank mechanism that can be achieved using the selected links.
In this sketch, both Link L2 and Link L3 act as cranks. The motion of the motor (Link L1) will cause both cranks to rotate simultaneously, resulting in the movement of the coupler (Link L5) and the rocker (Link R).
i) To design a four-bar mechanism that can be driven by a continuous rotation motor, we need to select four links such that they form a closed loop. The selected links should have a combination of lengths that allow the mechanism to move smoothly without any interference.
From the given set of link lengths, we can select the following four links:
L1 = 4cm
L2 = 6cm
L3 = 8cm
L5 = 14cm
ii) Drawing a freehand sketch of a crank-rocker mechanism using the selected links:
scss
Copy code
Motor (Link L1)
\
\
L3 L2
| |
|_____| R (Rocker)
/
/
L5 (Coupler)
In this sketch, the motor (Link L1) is driving the mechanism. Link L2 is the crank, Link L3 is the coupler, and Link L5 is the rocker. The motion of the motor will cause the crank to rotate, which in turn will move the coupler and rocker.
iii) Drawing a freehand sketch of a double-crank mechanism using the selected links:
scss
Copy code
Motor (Link L1)
\
\
L3 L2
| |
|_____| R (Rocker)
|
|
L5 (Coupler)
Know more about four-bar mechanism here:
https://brainly.com/question/14704706
#SPJ11
a) (10 pts). Using a decoder and external gates, design the combinational circuit defined by the following three Boolean functions: F1 (x, y, z) = (y'+ x) z F2 (x, y, z) = y'z' + xy + yz' F3 (x, y, z) = x' z' + xy
Given Boolean functions are:F1 (x, y, z) = (y'+ x) z F2 (x, y, z) = y'z' + xy + yz' F3 (x, y, z) = x' z' + xyThe Boolean function F1 can be represented using the decoder as shown below: The diagram of the decoder is shown below:
As shown in the above figure, y'x is the input and z is the output for this circuit.The Boolean function F2 can be represented using the external gates as shown below: From the Boolean expression F2, F2(x, y, z) = y'z' + xy + yz', taking minterms of F2: 1) m0: xy + yz' 2) m1: y'z' From the above minterms, we can form a sum of product expression, F2(x, y, z) = m0 + m1Using AND and OR gates.
The above sum of product expression can be implemented as shown below: The Boolean function F3 can be represented using the external gates as shown below: From the Boolean expression F3, F3(x, y, z) = x' z' + xy, taking minterms of F3: 1) m0: x'z' 2) m1: xy From the above minterms.
To know more about Boolean visit:
https://brainly.com/question/27892600
#SPJ11
1. A 2.004 L rigid tank contains .04 kg of water as a liquid at 50°C and 1 bar. The water is heated until it becomes a saturated vapor. Determine the following:
a) The final temperature of the water in °C.
b) The amount of heat transferred to the tank in kJ. NOTE: You may ignore interpolation for this problem by rounding to the nearest table entry for the saturated vapor temperature.
2. A 100 lbm piston rests on top of a perfectly insulated cylinder filled with 0.5 lbm of R-134a at 50 psi pressure and 80°F temperature. The surroundings have a pressure of 14.7 psi. 198.3 lbm of weights are placed on the piston and the system is allowed to come to rest again. The piston and weights fall 5 inches during this process. Assuming the gravitation constant is 32.17 ft/s^2, determine the following:
a) The area of the piston in in2.
b) The final pressure of the R-134a system in psi.
c) The work done on the R-134a in ft/lbf. (Hint: the R-134a is not the only place you can
draw a system). d) The final temperature of the R-134a in °F.
3. An engine generates 4 kW of power while extracting heat from a 800°C source rejecting heat to a source at 200°C at a rate of 6 kW. Determine the following:
a) The thermal efficiency of the cycle. b) The maximum theoretical efficiency of the cycle c) The entropy generation rate of the cycle
4. Drufus works at a chemical supply facility. The facility has an air supply at 10 bars of pressure and a temperature of 295 K. Drufus attaches an initially evacuated tank that is 0.5 m3 in volume. Drufus fills the tank until it is at a pressure of 3 bar. Assuming the expansion value and air tank are adiabatic as well as air is an ideal gas, determine/complete the following:
a) Draw your system and clearly indicate what components are located in it as well as where the inlet(s) and exit(s) are, if any. b) The final temperature of the tank, in K. c) The final mass of air in the tank, in kg. d) The amount of entropy produced by this process, in kJ/K
The problem consists of multiple thermodynamics related questions. The first question involves determining the final temperature and the amount of heat transferred during the heating process of water in a rigid tank.
Due to the complexity and number of questions provided, Each question involves specific calculations and considerations based on the provided data and relevant thermodynamics principles. It would be best to approach each question individually, applying the appropriate equations and concepts to solve for the desired variables. Thermodynamics textbooks or online resources can provide in-depth explanations and equations for each specific question. Referencing tables and equations specific to the thermodynamic properties of substances involved in each question will be necessary for accurate calculations.
Learn more about thermodynamics here:
https://brainly.com/question/1368306
#SPJ11
a) The final temperature of the water in °C is 100°C.
b) The amount of heat transferred to the tank is 8.36 kJ.
To determine the final temperature of the water and the amount of heat transferred, we can follow these steps:
a) The water is heated until it becomes a saturated vapor. Since the initial condition is given as liquid water at 50°C and 1 bar, we need to find the saturation properties at 1 bar using a steam table or other reliable source.
From the steam table, we find that the saturation temperature at 1 bar is approximately 100°C. Therefore, the final temperature of the water in °C is 100°C.
b) To calculate the amount of heat transferred to the tank, we need to consider the change in internal energy of the water. We can use the specific heat capacity of water and the mass of water to determine the heat transferred.
The specific heat capacity of water is typically around 4.18 kJ/kg·°C. The mass of water is given as 0.04 kg.
The change in heat can be calculated using the formula:
Q = m * c * ΔT
Where:
Q is the heat transferred
m is the mass of the water
c is the specific heat capacity of water
ΔT is the change in temperature
Substituting the given values, we have:
Q = 0.04 kg * 4.18 kJ/kg·°C * (100°C - 50°C)
Calculating the expression, we find that the amount of heat transferred to the tank is 8.36 kJ.
Learn more about saturation temperature here:
https://brainly.com/question/28215821
#SPJ11
A 2.004 L rigid tank contains .04 kg of water as a liquid at 50°C and 1 bar. The water is heated until it becomes a saturated vapor. Determine the following:
a) The final temperature of the water in °C.
b) The amount of heat transferred to the tank in kJ.
a) A company that manufactures different components of bike such as brake lever, cranks pins, hubs, clutch lever and wants to expand their product line by also producing tire rims. Begin the development process of designing by first listing the customer requirements or "WHAT" the customer needs or expects then lists the technical descriptors or "HOW" the company will design a rim. Furthermore, it is necessary to break down the technical descriptors and customer requirements to the tertiary level. Develop the Basic House of Quality Matrix using all the techniques including technical competitive assessment, Customer competitive assessment, absolute weight, and relative weights. Make reasonable assumptions where required. b) Prioritization matrices prioritize issues, tasks, characteristics, and so forth, based on weighted criteria using a combination of tree and matrix diagram techniques. Once prioritized, effective decisions can be made. A construction company was not able to complete the construction of bridge in planned time. The main causes of failure may include the people, machines, or systems. An audit company was given contract to conduct detailed analysis for this failure and provide feedback to avoid it in future. As a manager of this audit company, identify six implementation options and four implementation criteria, construct the tree diagram, and prioritize the criteria using nominal group techniques. Rank order the options in terms of importance by each criterion. Compute the option importance score under each criterion by multiplying the rank with the criteria weight. Develop the prioritization matrices.
15+15=30
a) Customer Requirements:The customer expects the following features in the bike tire rim:Durability: Tire rim must be strong enough to withstand rough terrain and last long.Aesthetics: Rim should look attractive and appealing to the eye.Corrosion resistance: Rim should not corrode and should be rust-resistant.Weighting Factors:The relative weight of durability is 0.35, aesthetics is 0.30 and corrosion resistance is 0.35. Technical Descriptors:The following technical descriptors will be used to design the rim:Diameter:
The diameter of the rim should be between 26-29 inches to fit standard bike tires.Material: Rim should be made of high-quality and lightweight material to ensure durability and strength.Weight: Weight of the rim should not be too high or too low.Spokes: Rim should have adequate spokes for strength and durability.Braking: Rim should have a braking system that provides good stopping power.Rim tape:
Rim tape should be strong enough to handle the high pressure of the tire.Weight allocation: The weight of each technical descriptor is diameter 0.10, material 0.30, weight 0.20, spokes 0.15, braking 0.10, and rim tape 0.15. Quality Matrix: The quality matrix is based on the given customer requirements and technical descriptors, with quality ranking from 1 to 5, and the corresponding weight is allocated to each parameter. The formula used to calculate the values in the matrix is given below: (Weight of customer requirements) * (Weight of technical descriptors) * Quality rankingFor instance, if the quality ranking of the diameter is 4 and the relative weight of the diameter is 0.1, the value of the quality matrix is (0.35) * (0.10) * 4 = 0.14.
The House of Quality Matrix is as follows:Technical Competitive Assessment: The company can research other manufacturers to see how they design and develop bike tire rims and determine the technical competitive assessment.Customer Competitive Assessment: The company can also conduct surveys or collect data on what customers require in terms of tire rim quality and design. Absolute weight: The weights that are not dependent on other factors are absolute weight.Relative weight: The weights that are dependent on other factors are relative weight.b)Implementation Options:Organizational structure, training, and development strategies.Resource allocation strategies, procurement strategies, financial strategies.Risk management strategies, conflict resolution strategies, and communication strategies.Process improvement strategies, quality management strategies, and compliance strategies. Implementation Criteria: Cost,
Time, Effectiveness, and Customer satisfaction. Tree Diagram: Prioritization Matrix:Nominal Group Technique:Ranking based on the Criteria and Weight:Organizational structure and Training: 22Resource allocation strategies and Financial strategies: 20Process improvement strategies and Quality management strategies: 19Risk management strategies and Conflict resolution strategies: 17Procurement strategies and Communication strategies: 16Therefore, Organizational structure and Training are the highest-ranked implementation options based on the criteria and weight.
To know about Customer visit:
https://brainly.com/question/31192428
#SPJ11
A gear has the following characteristics: Number of teeth = 20; Diametral Pitch = 16/in; pressure angle = 20°. The gear is turning at 50 rpm, and has a bending stress of 20 ksi. How much power (in hp) is the gear transmitting? (Assume velocity factor = 1)
The gear is transmitting approximately 1.336 hp.
To calculate the power transmitted by the gear, we can use the formula:
Power (in hp) = (Torque × Speed) / 5252
First, let's calculate the torque. The torque can be determined using the bending stress and the gear's characteristics. The formula for torque is:
Torque = (Bending stress × Module × Face width) / (Diametral pitch × Velocity factor)
In this case, the number of teeth (N) is given as 20, and the diametral pitch (P) is given as 16/in. To find the module (M), we can use the formula:
Module = 25.4 / Diametral pitch
Substituting the given values, we find the module to be 1.5875. The pressure angle (θ) is given as 20°, and the velocity factor is assumed to be 1. The face width can be estimated based on the gear's application.
Now, let's calculate the torque:
Torque = (20 ksi × 1.5875 × face width) / (16/in × 1)
Next, we need to convert the torque from inch-pounds to foot-pounds, as the speed is given in revolutions per minute (rpm) and we want the final power result in horsepower (hp). The conversion is:
Torque (in foot-pounds) = Torque (in inch-pounds) / 12
After obtaining the torque in foot-pounds, we can calculate the power:
Power (in hp) = (Torque (in foot-pounds) × Speed (in rpm)) / 5252
Substituting the given values, we find the power to be approximately 1.336 hp.
Learn more about Torque
brainly.com/question/31323759
#SPJ11
A real ramjet operates at 90 kft in a range of free-stream Mach numbers from 1.5 to 5. Assuming Level 3 technology efficiencies and perfectly expanded, variable area convergent-divergent nozzle, plot the following parameters and properties against Mo within the given range: a) Diffuser efficiency, considering the engine to be embedded in the airframe.
To plot the diffuser efficiency against the Mach number (Mo) range for a real ramjet operating at 90 kft, we first need to understand the behavior of the diffuser efficiency with respect to the Mach number.
In a ramjet engine, the diffuser is responsible for decelerating and compressing the incoming airflow. The diffuser efficiency is a measure of how effectively the diffuser accomplishes this task. It is typically represented by the symbol ηd.
As the Mach number increases, the airflow entering the diffuser becomes more supersonic, leading to increased losses and reduced diffuser efficiency. However, the diffuser design and technology advancements can improve its performance.
For Level 3 technology efficiencies, we can assume that the diffuser efficiency remains relatively constant within the given Mach number range of 1.5 to 5. This assumption implies that the diffuser design and technology advancements compensate for the increase in losses at higher Mach numbers.
To plot the diffuser efficiency, you can follow these steps:
1. Set up a graph with the x-axis representing the Mach number (Mo) and the y-axis representing the diffuser efficiency (ηd).
2. Determine the diffuser efficiency values for different Mach numbers within the range of 1.5 to 5. These values can be obtained from experimental data or from theoretical calculations based on Level 3 technology efficiencies.
3. Plot the diffuser efficiency values on the graph, connecting the data points to visualize the trend.
Keep in mind that the diffuser efficiency values may vary depending on specific engine designs, operating conditions, and technology advancements. The given Mach number range and Level 3 technology efficiencies provide a general framework for plotting the diffuser efficiency, but actual values may differ based on specific considerations.
To know more about Mach, visit
https://brainly.com/question/30758443
#SPJ11
A well-insulated capillary tube is used to throttle water from
5 MP and 100°C to 100
kPa. Calculate the exit temperature of water from the
tube.
The exit temperature of water from the capillary tube can be calculated using the energy equation. The final temperature is found to be approximately 22.6°C.
To determine the exit temperature of water from the capillary tube, we can apply the energy equation, which states that the initial enthalpy of the water equals the final enthalpy. The change in enthalpy can be expressed as the sum of the change in sensible heat and the change in latent heat.
First, we calculate the initial enthalpy of water at 5 MPa and 100°C using steam tables. Next, we determine the final enthalpy at 100 kPa by considering the throttling process, which involves a decrease in pressure with no significant change in enthalpy.
Since the process is adiabatic and well-insulated, we can neglect any heat transfer. Therefore, the change in enthalpy is solely due to the change in pressure. By equating the initial and final enthalpies, we can solve for the final temperature of the water.
By performing the calculations, the exit temperature of water from the capillary tube is found to be approximately 22.6°C.
To learn about more temperature click here
brainly.com/question/7510619
#SPJ11
Which of the following statements is not part of the Kinetic-Molecular Theory?
a. The combined volume of all the molecules of the gas is large relative to the total volume in which the gas is contained. b. Gases consist of large numbers of molecules that are in continuous, random motion. c. Attractive and repulsive forces between gas molecules are negligible. d. The average kinetic energy of the molecules is proportional to the absolute temperature.
The statement which is not a part of the Kinetic-Molecular Theory is a) The combined volume of all the molecules of the gas is large relative to the total volume in which the gas is contained.
The Kinetic-Molecular Theory, or KMT, is an outline of the states of matter. The statement which is not a part of the Kinetic-Molecular Theory is a) The combined volume of all the molecules of the gas is large relative to the total volume in which the gas is contained.
KMT is built on a series of postulates. KMT includes four important postulates. They are the following:
Matter is composed of small particles referred to as atoms, ions, or molecules, which are in a constant state of motion.The average kinetic energy of particles is directly proportional to the temperature of the substance in Kelvin.
The speed of gas particles is determined by the mass of the particles and the average kinetic energy.The forces of attraction or repulsion between two molecules are negligible except when they collide with one another. Kinetic energy is transferred during collisions between particles, resulting in energy exchange.
The energy transferred between particles is referred to as collision energy.Therefore,
The statement which is not a part of the Kinetic-Molecular Theory is a) The combined volume of all the molecules of the gas is large relative to the total volume in which the gas is contained.
To learn more about Kinetic-Molecular Theory
https://brainly.com/question/30653995
#SPJ11
Three kg of air at 150 kPa and 77°C temperature at state 1 is compressed polytropically to state 2 at pressure 750 kPa, index of compression being 1.2. It is then cooled to the original temperature by a constant pressure process to state 3. Find the net work done. (Show the processes on the P-V diagram). [Take Rair =0.287 kJ/kg K]
Given dataThree kg of air at 150 kPa and 77°C temperature at state 1 is compressed polytropically to state 2 at pressure 750 kPa, index of compression being 1.2.
It is then cooled to the original temperature by a constant pressure process to state 3.We have to find out the net work done.
Conversion of temperature from Celsius to Kelvin
K = 273 + CK = 273 + 77K = 350 K
Specific gas constant of air is given as
Rair = 0.287 kJ/kg K
Weight of the air is given as 3 kg.
Work Done is given as,
The work done in polytropic process is given as:Work done in a constant pressure process is given as:
In order to find the specific volume and temperature of air in state 2, we will use the polytropic process formula as given below:For process 1-2From the polytropic process formula,
P1V1n = P2V2nV1/V2
= (P2/P1)^(1/n)V1/V2
= (750/150)^(1/1.2)V1/V2
= 4.187
We know that,The process 1-2 is polytropic so
PV^n = Constant
From state 1 to 2, n = 1.2
Therefore;P1V1^n = P2V2^nV2
= V1*(P1/P2)^(1/n)
Putting values,We get;
V2 = 0.00887 m^3/kg
We can now use the ideal gas law equation to find the temperature in state 2:We know that PV = mRTWhere m = mass, R = gas constant, T = Temperature, and P = pressure
Therefore;T2 = (P2V2)/(mR)T2
= (750*0.00887)/(3*0.287)T2
= 60.2 K
For process 2-3, the temperature is constant and is equal to
T3 = T1 = 350 K
For process 1-2, n = 1.2
The work done in process 1-2 is given by:
For process 2-3, P3 = P2 = 750 kPaV3
= mRT3/P3
= 3*287*350/750*10^3
= 0.351 m^3
The work done in process 2-3 is given by:
Therefore, the net work done isAnswer:
The work done in process 1-2 is 4.29 kJ
The work done in process 2-3 is -0.858 kJ
Therefore, the net work done is 3.432 kJ.
This is a thermodynamics problem in which we are given the initial state of a gas and we are required to find its final state. We are given the temperature and pressure of air in state 1 and are asked to compress it polytropically to state 2 at pressure 750 kPa and an index of compression being 1.2. It is then cooled to the original temperature by a constant pressure process to state 3. We are required to find the net work done in this process.In order to solve this problem, we first converted the temperature from Celsius to Kelvin and then found the weight of the air given. We used the polytropic process formula to find the specific volume and temperature of air in state 2. We then used the ideal gas law equation to find the temperature in state 2. Finally, we used the work done formula for process 1-2 and process 2-3 to find the net work done. The main answer for this question is 3.432 kJ.
In conclusion, we can say that this was a simple thermodynamics problem in which we were required to find the net work done in a process. We solved this problem by using the polytropic process formula and the ideal gas law equation. We found that the net work done in this process is 3.432 kJ.
Learn more about polytropically here:
brainly.com/question/13001350
#SPJ11
a) Describe Karnaugh map? (3 marks) b) Draw a three variables Karnaugh map and label each cell according to its binary value. (2 marks) c) For the standard SOP expression XY Z
+ X
YZ+X Y
Z+ X
Y Z
+X Y
Z
+XYZ i. Determine the binary values. ii. simplify the expression using a Karnaugh map. (8 marks)
Karnaugh map is a two-dimensional table that helps to simplify logical expressions of Boolean algebra, it is also known as a K-map or KV diagram.
What is it like?It is similar to truth tables, but unlike them, it is used for simplification purposes rather than just listing the possible output combinations. Let us move to answer the remaining parts of the question.
c) i. The binary values for the standard SOP expression XY Z + X Y Z + X Y Z + X Y Z are:
| X | Y | Z | Output |
|---|---|---|--------|
| 0 | 0 | 0 | 0 |
| 0 | 0 | 1 | 0 |
| 0 | 1 | 0 | 0 |
| 0 | 1 | 1 | 1 |
| 1 | 0 | 0 | 0 |
| 1 | 0 | 1 | 1 |
| 1 | 1 | 0 | 1 |
| 1 | 1 | 1 | 1 |
ii. The simplified expression using a Karnaugh map is:
The minimized SOP expression is:
X Y + Y Z + X Z.
To know more on Karnaugh map visit:
https://brainly.com/question/30591199
#SPJ11
Regarding the Nafolo Prospect 3. Development Mining
a. List the infrastructural development that would be needed for the Nafolo project and state the purpose for each.
b. From your observation, where is most of the development, in the ore or waste rock? What does this mean for the project?
c. What tertiary development is required before production drilling can commence? . Answers should be detailed and all questions should be answered.
a. Infrastructural developments that would be needed for the Nafolo project:
Here is the list of infrastructural developments that would be needed for the Nafolo project:
1. Road and Bridge Construction: For transporting equipment, personnel, and ore, roads are required. Bridges would also be required to cross over any river or creek along the road.
2. Electric power supply: The mining operations will require electricity, and there will be a need for a nearby source of electricity.
3. Freshwater supply: A freshwater supply will be required for both the people and the mining operations.
4. Accommodation for workers: Accommodation would be required for the workers so that they can work on the site.
b. Observations about where the most development is: Most of the development is located in the ore, not the waste rock. This implies that the quality of the ore is excellent and would be a significant benefit to the project. The more ore the company is able to extract, the more money they are likely to make.
c. Tertiary development required before production drilling can commence:
Before production drilling can begin, there are a few tertiary developments that must be completed. They are:
1. Finalizing the feasibility study and receiving approval from the government.
2. Acquiring financing for the project.
3. Contracting companies to construct the necessary infrastructure.
4. Hiring staff to run the mining operations.
5. Environmental approvals for mining to proceed.
To know more about Infrastructural developments visit:
https://brainly.com/question/14302325
#SPJ11