Answer:
12.25m/s
Explanation:
[tex]d=v_ot+\dfrac{1}{2}at^2[/tex]
Since the initial velocity of the dropped rock is 0, you can write this as:
[tex]d=\dfrac{1}{2}(9.8)(3)^2=44.1m[/tex]
Now, you can set up the equation for the thrown rock:
[tex]44.1=v_o(2)+\dfrac{1}{2}(9.8)(2)^2 \\\\\\44.1=2v_o+19.6 \\\\\\2v_o=24.5 \\\\\\v_o=12.25m/s[/tex]
Hope this helps!
In 11.8 s, 151 bullets strike and embed themselves in a wall. The bullets strike the wall perpendicularly. Each bullet has a mass of 5 x 10^-3 kg and a speed of 1110 m/s.
Required:
a. What is the average change in momentum per second for the bullets?
b. Determine the average force exerted on the wall.
c. Assuming the bullets are spread out over an area of 3.0×10^−4m^2 obtain the average pressure they exert on this region of the wall.
Answer:
a. ΔP/Δt = 42.6 N
b. F = 42.6 N
c. P = 142042.4 Pa = 1.42 KPa
Explanation:
a.
First, we find the change in momentum of the bullets. For one bullet:
ΔP = m(Vf - Vi)
where,
ΔP = Change in Momentum = ?
m = mass of bullet = 5 x 10⁻³ kg
Vf = Final Speed = 1110 m/s
Vi = Initial Speed = 0 m/s (Since bullets are initially at rest)
Therefore,
ΔP = (3 x 10⁻³ kg)(1110 m/s - 0 m/s)
ΔP = 3.33 N.s
For 151 bullets:
ΔP = (151)(3.33 N.s)
ΔP = 502.83 N.s
Now, dividing this by time interval, Δt = 11.8 s
ΔP/Δt = 502.83 N.s/ 11.8 s
ΔP/Δt = 42.6 N
b.
According to Newton's Second Law, the force is equal to rate of change of linear momentum:
Average Force = F = ΔP/Δt
F = 42.6 N
c.
The pressure is given by:
Average Pressure = P = Average Force/Area
P = 42.6 N/ 3 x 10⁻⁴ m²
P = 142042.4 Pa = 1.42 KPa
What is the internal energy (to the nearest joule) of 10 moles of Oxygen at 100 K?
(Given, the universal gas constant = 8.315 J/(mol.k))
Answer:
U = 12,205.5 J
Explanation:
In order to calculate the internal energy of an ideal gas, you take into account the following formula:
[tex]U=\frac{3}{2}nRT[/tex] (1)
U: internal energy
R: ideal gas constant = 8.135 J(mol.K)
n: number of moles = 10 mol
T: temperature of the gas = 100K
You replace the values of the parameters in the equation (1):
[tex]U=\frac{3}{2}(10mol)(8.135\frac{J}{mol.K})(100K)=12,205.5J[/tex]
The total internal energy of 10 mol of Oxygen at 100K is 12,205.5 J
A 50 gram meterstick is placed on a fulcrum at its 50 cm mark. A 20 gram mass is attached at the 12 cm mark. Where should a 40 gram mass be attached so that the meterstick will be balanced in rotational equilibrium
Answer:
The 40g mass will be attached at 69 cm
Explanation:
First, make a sketch of the meterstick with the masses placed on it;
--------------------------------------------------------------------------
↓ Δ ↓
20 g.................50 cm.................40g
38 cm y cm
Apply principle of moment;
sum of clockwise moment = sum of anticlockwise moment
40y = 20 (38)
40y = 760
y = 760 / 40
y = 19 cm
Therefore, the 40g mass will be attached at 50cm + 19cm = 69 cm
12cm 50 cm 69cm
--------------------------------------------------------------------------
↓ Δ ↓
20 g.................50 cm.................40g
38 cm 19 cm
A heavy, 6 m long uniform plank has a mass of 30 kg. It is positioned so that 4 m is supported on the deck of a ship and 2 m sticks out over the water. It is held in place only by its own weight. You have a mass of 70 kg and walk the plank past the edge of the ship. How far past the edge do you get before the plank starts to tip, in m
Answer:
about 1 meter
Explanation:
The distance past the edge that the man will get before the plank starts to tip is; 0.4285 m
We are given;
Mass of plank; m = 30 kg
Length of plank; L = 6m
Mass of man; M = 70 kg
Since the plank has 2 supports which are the deck of the ship, then it means that, we can take moments about the right support before the 2m stick out of the plank.
Thus;
Moment of weight of plank about the right support;
τ_p = mg((L/2) - 2)
τ_p = 30 × 9.8((6/2) - 2)
τ_p = 294 N.m
Moment of weight of man about the right support;
τ_m = Mgx
where x is the distance past the edge the man will get before the plank starts to tip.
τ_m = 70 × 9.8x
τ_m = 686x
Now, moment of the board is counterclockwise while that of the man is clockwise. Thus;
τ_m = τ_p
686x = 294
x = 294/686
x = 0.4285 m
Read more at; https://brainly.com/question/22150651
The robot HooRU is lost in space, floating around aimlessly, and radiates heat into the depths of the cosmos at the rate of 13.1 W. HooRU's surface area is 1.55 m2 and the emissivity of its surface is 0.287. Ignoring the radiation that HooRU absorbs from the cold universe, what is HooRU's temperature T?
Answer:
The temperature is [tex]T = 168.44 \ K[/tex]
Explanation:
From the question ewe are told that
The rate of heat transferred is [tex]P = 13.1 \ W[/tex]
The surface area is [tex]A = 1.55 \ m^2[/tex]
The emissivity of its surface is [tex]e = 0.287[/tex]
Generally, the rate of heat transfer is mathematically represented as
[tex]H = A e \sigma T^{4}[/tex]
=> [tex]T = \sqrt[4]{\frac{P}{e* \sigma } }[/tex]
where [tex]\sigma[/tex] is the Boltzmann constant with value [tex]\sigma = 5.67*10^{-8} \ W\cdot m^{-2} \cdot K^{-4}.[/tex]
substituting value
[tex]T = \sqrt[4]{\frac{13.1}{ 0.287* 5.67 *10^{-8} } }[/tex]
[tex]T = 168.44 \ K[/tex]
A charged particle q moves at constant velocity through a crossed electric and magnetic fields (E and B, which are both constant in magnitude and direction). Write the magnitude of the electric force on the particle in terms of the variables given. Do the same for the magnetic force
Answer:
The magnitude of the electric force on the particle in terms of the variables given is, F = qE
The magnitude of the magnetic force on the particle in terms of the variables given is, F = q (v x B)
Explanation:
Given;
a charged particle, q
magnitude of electric field, E
magnitude of magnetic field, B
The magnitude of the electric force on the particle in terms of the variables given;
F = qE
The magnitude of the magnetic force on the particle in terms of the variables given;
F = q (v x B)
where;
v is the constant velocity of the charged particle
Answer:
The magnitude of the electric force acting on a charged particle moving through an electric field = |qE|
The magnitude of the magnetic force of a charged particle moving at a particular velocity through a magnetic field = |qv × B|
Explanation:
The electric force acting on a charged particle, q, moving through an electric field, E, is given as a product of the charge on the particle (a scalar quantity) and the electric field (a vector quantity).
Electric force = qE
The magnitude of the electric force = |qE|
That is, magnitude of the product of the charge and the electric field vector.
The magnetic force acting on a charged particle, q, moving with a velocity, v, through a magnetic field, B is a vector product of qv [a product of the charge of the particle (a scalar quantity) and the velocity of the particle (a vector quantity)] and B (a vector quantity).
It is given mathematically as (qv × B)
The magnitude of the magnetic force is the magnitude of the vector product obtained.
Magnitude of the magnetic force = |qv × B|
Hope this Helps!!!
Two metal spheres are hanging from nylon threads. When you bring the spheres close to each other, they tend to attract. Based on this information alone, discuss all the possible ways that the spheres could be charged. Is it possible that after the spheres touch, they will cling together? Explain.
Explanation:
In the given question, the two metal spheres were hanged with the nylon thread.
When these two spheres were brought close together, they attracted each other. The attraction between these spheres is the result of the opposite charges between them.
The possible ways by which these two metal spheres can be charged are by induction that is touching the metal or by rubbing them.
During induction, the same charges are transferred to each sphere. In this case, either both the spheres will be negatively charged or positively charged.
It is not possible that after the sphere touch each other they will cling together because the same charge repels each other and during touching, if one sphere is neutral, then the charged one will transfer the same charge. And as we know that same charge repel each other therefore they will repel each other.
The cart travels the track again and now experiences a constant tangential acceleration from point A to point C. The speeds of the cart are 4.50 m/s at point A and 5.00 m/s at point C. The cart takes 4.00 s to go from point A to point C, and the cart takes 1.60 s to go from point B to point C. What is the cart's speed at point B
Answer:
Vi = 4.8 m/s
Explanation:
First we need to find the magnitude of constant tangential acceleration. For that purpose we use the following formula between points A and C:
a = (Vf - Vi)/t
where,
a = constant tangential acceleration from A to C = ?
Vf = Final Velocity at C = 5 m/s
Vi = Initial Velocity at A = 4.5 m/s
t = time taken to move from A to C = 4 s
Therefore,
a = (5 m/s - 4.5 m/s)/4 s
a = 0.125 m/s²
Now, applying the same equation between points B and C:
a = (Vf - Vi)/t
where,
a = constant tangential acceleration from A to B = 0.125 m/s²
Vf = Final Velocity at C = 5 m/s
Vi = Initial Velocity at B = ?
t = time taken to move from B to C = 1.6 s
Therefore,
0.125 m/s² = (5 m/s - Vi)/1.6 s
Vi = 5 m/s - (0.125 m/s²)(1.6 s)
Vi = 4.8 m/s
If the magnitude of the magnetic field is 2.50 mT at a distance of 12.6 cm from a long straight current carrying wire, what is the magnitude of the magnetic field at a distance of 19.8 cm from the wire
Answer:
The magnetic field at a distance of 19.8 cm from the wire is 1.591 mT
Explanation:
Given;
first magnetic field at first distance, B₁ = 2.50 mT
first distance, r₁ = 12.6 cm = 0.126 m
Second magnetic field at Second distance, B₂ = ?
Second distance, r₂ = ?
Magnetic field for a straight wire is given as;
[tex]B = \frac{\mu I}{2 \pi r}[/tex]
Where:
μ is permeability
B is magnetic field
I is current flowing in the wire
r distance to the wire
[tex]Let \ \frac{\mu I}{2\pi} \ be \ constant; = K\\\\B = \frac{K}{r} \\\\K = Br\\\\B_1r_1 = B_2r_2\\\\B_2 =\frac{B_1r_1}{r_2} \\\\B_2 = \frac{2.5*10^{-3} *0.126}{0.198} \\\\B_2 = 1.591 *10^{-3}\ T\\\\B_2 = 1.591 \ mT[/tex]
Therefore, the magnetic field at a distance of 19.8 cm from the wire is 1.591 mT
A solenoidal coil with 23 turns of wire is wound tightly around another coil with 310 turns. The inner solenoid is 20.0 cm long and has a diameter of 2.20 cm. At a certain time, the current in the inner solenoid is 0.130 A and is increasing at a rate of 1800 A/s. For this time, calculate:
(a) the average magnetic flux through each turn of the inner solenoid;
(b) the mutual inductance of the two solenoids;
(c) the emf induced in the outer solenoid by the changing current in the inner solenoid.
Answer:
Explanation:
From the given information:
(a)
the average magnetic flux through each turn of the inner solenoid can be calculated by the formula:
[tex]\phi _ 1 = B_1 A[/tex]
[tex]\phi _ 1 = ( \mu_o \dfrac{N_i}{l} i_1)(\pi ( \dfrac{d}{2})^2)[/tex]
[tex]\phi _ 1 = ( 4 \pi *10^{-7} \ T. m/A ) ( \dfrac{310}{20*10^{-2} \ m }) (0.130 \ A) ( \pi ( \dfrac{2.20*10^{-2} \ m }{2})^ 2[/tex]
[tex]\phi_1 = 9.625 * 10^{-8} \ Wb[/tex]
(b)
The mutual inductance of the two solenoids is calculated by the formula:
[tex]M = 23 *\dfrac{9.625*10^{-8} \ Wb}{0.130 \ A}[/tex]
M = [tex]1.703 *10^{-5}[/tex] H
(c)
the emf induced in the outer solenoid by the changing current in the inner solenoid can be calculate by using the formula:
[tex]\varepsilon = -N_o \dfrac{d \phi_1}{dt}[/tex]
[tex]\varepsilon = -M \dfrac{d i_1}{dt}[/tex]
[tex]\varepsilon = -(1.703*10^{-5} \ H) * (1800 \ A/s)[/tex]
[tex]\varepsilon = -0.030654 \ V[/tex]
[tex]\varepsilon = -30.65 \ V[/tex]
Light rays from stars bend toward smaller angles as they enter Earth's atmosphere. a. Explain why this happens using Snell's law and the speed of light. b. Where are the actual stars in relation to their apparent position as viewed from the Earth's surface?
Answer:
Following are the answer to this question:
Explanation:
In option (a):
The principle of Snells informs us that as light travels from the less dense medium to a denser layer, like water to air or a thinner layer of the air to the thicker ones, it bent to usual — an abstract feature that would be on the surface of all objects. Mostly, on the contrary, glow shifts from a denser with a less dense medium. This angle between both the usual and the light conditions rays is referred to as the refractive angle. Throughout in scenario, the light from its stars in the upper orbit, the surface area of both the Earth tends to increase because as light flows from the outer atmosphere towards the Earth, it defined above, to a lesser angle.In option (b):
Rays of light, that go directly down wouldn't bend, whilst also sun source which joins the upper orbit was reflected light from either a thicker distance and flex to the usual, following roughly the direction of the curve of the earth. Throughout the zenith specific position earlier in this thread, astronomical bodies appear throughout the right position while those close to a horizon seem to have been brightest than any of those close to the sky, and please find the attachment of the diagram.Two narrow slits, illuminated by light consisting of two distinct wavelengths, produce two overlapping colored interference patterns on a distant screen. The center of the eighth bright fringe in one pattern coincides with the center of the third bright fringe in the other pattern. What is the ratio of the two wavelengths?
Answer:
The ration of the two wavelength is [tex]\frac{\lambda_1}{\lambda_2} = \frac{8}{3}[/tex]
Explanation:
Generally two slit constructive interference can be mathematically represented as
[tex]\frac{y}{L} = \frac{m * \lambda}{d}[/tex]
Where y is the distance between fringe
d is the distance between the two slit
L is the distance between the slit and the wall
m is the order of the fringe
given that y , L , d are constant we have that
[tex]\frac{m }{\lambda } = constant[/tex]
So
[tex]\frac{m_1 }{\lambda_1 } = \frac{m_2 }{\lambda_2 }[/tex]
So [tex]m_1 = 8[/tex]
and [tex]m_2 = 3[/tex]
=> [tex]\frac{m_2}{m_1} = \frac{\lambda_1}{\lambda_2}[/tex]
=> [tex]\frac{8}{3} = \frac{\lambda_1}{\lambda_2}[/tex]
So
[tex]\frac{\lambda_1}{\lambda_2} = \frac{8}{3}[/tex]
A man stands on a platform that is rotating (without friction) with an angular speed of 1.2 rev/s; his arms are outstretched and he holds a brick in each hand.The rotational inertia of the system consisting of the man, bricks, and platform about the central vertical axis of the platform is 6.0 k g times m squared. If by moving the bricks the man decreases the rotational inertia of the system to 2.0 k g times m squared, what is the resulting angular speed of the platform in rad/s
Answer:
resulting angular speed = 3.6 rev/s
Explanation:
We are given;
Initial angular speed; ω_i = 1.2 rev/s
Initial moment of inertia;I_i = 6 kg/m²
Final moment of inertia;I_f = 2 kg/m²
From conservation of angular momentum;
Initial angular momentum = Final angular momentum
Thus;
I_i × ω_i = I_f × ω_f
Making ω_f the subject, we have;
ω_f = (I_i × ω_i)/I_f
Plugging in the relevant values;
ω_f = (6 × 1.2)/2
ω_f = 3.6 rev/s
Potential difference of a battery is 2.2 V when it is connected
across a resistance of 5 ohm, if suddenly the potential difference
falls to 1.8V, its internal resistance will be
Answer:
1.1ohms
Explanation:
According to ohms law E = IR
If potential difference of a battery is 2.2 V when it is connected across a resistance of 5 ohm and if suddenly the voltage Falls to 1.8V then the current in the 5ohms resistor I = V/R = 1.8/5
I = 0.36A (This will be the load current).
Before we can calculate the value of the internal resistance, we need to know the voltage drop across the internal resistance.
Voltage drop = 2.2V - 1.8V = 0.4V
Then we calculate the internal resistance using ohms law.
According to the law, V = Ir
V= voltage drop
I is the load current
r = internal resistance
0.4 = 0.36r
r = 0.4/0.36
r = 1.1 ohms
Set the battery to a value between 0.0 V and 1.5 V. Now drag the voltage meter toward the capacitor and move the red and black leads to measure the voltage. Determine the potential difference between the two plates and whether the top plate is at higher or lower voltage than the bottom plate
Answer:
the positive terminal has higher potential(voltage) than the negative. Any terminal at the positive terminal has higher potential
Explanation:
ΔV =Vtop - Vbottom
Cart A, with a mass of 0.20 kg, travels on a horizontal air trackat 3.0m/s and hits cart B, which has a mass of 0.40 kg and is initially traveling away from Aat 2.0m/s. After the collision the center of mass of the two cart system has a speed of:____________.A. zeroB. 0.33m/sC. 2.3m/sD. 2.5m/sE. 5.0m/s
Answer:
[tex]\large \boxed{\text{C. 2.3 m/s}}[/tex]
Explanation:
Data:
[tex]m_{\text{A} } = \text{0.20 kg};\,v_{\text{Ai}} = \text{3.0 m/s}\\m_{\text{B} } = \text{0.40 kg};\,v_{\text{Bi}} = \text{2.0 m/s}\\[/tex]
Calculation:
This is a perfectly inelastic collision. The two carts stick together after the collision and move with a common final velocity.
The conservation of momentum equation is
[tex]\begin{array}{rcl}m_{\text{A}}v_{\text{Ai}} +m_{\text{B}} v_{\text{Bi}}&=&(m_{\text{A}} + m_{\text{B}})v_{\text{f}}\\0.20\times 3.0 + 0.40\times 2.0 & = & (0.20 + 0.40)v_{\text{f}}\\0.60 + 0.80 & = & 0.60v_{\text{f}}\\1.40 & = & 0.60v_{\text{f}}\\v_{\text{f}}&=& \dfrac{1.40}{0.60}\\\\& = & \textbf{2.3 m/s}\\\end{array}\\\text{The centre of mass has a velocity of $\large \boxed{\textbf{2.3 m/s}}$}[/tex]
While sitting in your car by the side of a country road, you see your friend, who happens to have an identical car with an identical horn, approaching you. You blow your horn, which has a frequency of 260 Hz; your friend begins to blow his horn as well, and you hear a beat frequency of 5.0 Hz. Part A How fast is your friend approaching you
Answer:
-6.49 m/s
Explanation:
This is doppler effect.
The equation is;
F_l = [(v + v_l)/(v + v_s)]F_s
Where;
F_l is frequency observed by the listener
v is speed of sound
v_l is speed of listener
v_s is speed of source of the sound
F_s is frequency of the source of the sound
In this question, the source of the sound is the moving vehicle.
Thus;
F_l = F_beat + F_s
We are given beat frequency (f_beat) as 5 Hz while source frequency (F_s) as 260 Hz.
So,
F_l = 5 + 260
F_l = 265 Hz
Since listener is sitting by car, thus; v_l = 0 m/s
Thus,from our doppler effect equation, let's make v_s the subject;
v_s = F_s[(v + v_l)/F_l] - v
Speed of sound has a value of v = 344 m/s
Thus;
v_s = 260[(344 + 0)/265] - 344
v_s = -6.49 m/s
This value is negative because the source is moving towards the listener
13. Under what condition (if any) does a moving body experience no energy even though there
is a net force acting on it?
(2 marks)
Answer:
When the Net Forces are equal to 0
Explanation:
Momentum of a body can be defined as product of mass and velocity. It is in the same direction as in velocity. When the momentum of a body doesn't change, it is said to be conserved. If the momentum of a body is constant, the the net forces acting on a body becomes zero. When net forces acting on a body is zero, it means that no kinetic energy is being lost or gained, hence the kinetic energy is also conserved. If no energy is being gained or lost, it means that the body will experience no energy.
A 4.5 kg ball swings from a string in a vertical circle such that it has constant sum of kinetic and gravitational potential energy. Ignore any friction forces from the air or in the string. What is the difference in the tension between the lowest and highest points on the circle
Answer:
88.29 N
Explanation:
mass of the ball = 4.5 kg
weight of the ball will be = mass x acceleration due to gravity(9.81 m/s^2)
weight W = 4.5 x 9.81 = 44.145 N
centrifugal forces Tc act on the ball as it swings.
At the top point of the vertical swing,
Tension on the rope = Tc - W.
At the bottom point of the vertical swing,
Tension on the rope = Tc + W
therefore,
difference in tension between these two points will be;
Net tension = tension at bottom minus tension at the top
= Tc + W - (Tc - W) = Tc + W -Tc + W
= 2W
imputing the value of the weight W, we have
2W = 2 x 44.145 = 88.29 N
A block slides down a ramp with friction. The friction experienced by the block is 21 N. The mass of the block is 8 kg. The ramp is 6 meters long (meaning, the block slides across 6 meters of ramp with friction). The block is originally 2 meters vertically above the ground (the bottom of the ramp). What is the change in energy of the block due to friction, expressed in Joules
Complete Question
The complete question is shown on the first uploaded image
Answer:
the change in energy of the block due to friction is [tex]E = -126 \ J[/tex]
Explanation:
From the question we are told that
The frictional force is [tex]F_f = 21 \ N[/tex]
The mass of the block is [tex]m_b = 8 \ kg[/tex]
The length of the ramp is [tex]l = 6 \ m[/tex]
The height of the block is [tex]h = 2 \ m[/tex]
The change in energy of the block due to friction is mathematically represented as
[tex]\Delta E = - F_s * l[/tex]
The negative sign is to show that the frictional force is acting against the direction of the block movement
Now substituting values
[tex]\Delta E = -(21)* 6[/tex]
[tex]\Delta E = -126 \ J[/tex]
3.Cuanto Calor pierden 514 ml de agua si su temperatura desciende de 12°C a 11°C. Expresa el resultado en calorias.
514 cal
51.4 Kcal
514J/cal
5.149 Cal
Answer:
514 cal
Explanation:
In order to calculate the lost heat by the amount of water you first take into account the following formula:
[tex]Q=mc(T_2-T_1)[/tex] (1)
Q: heat lost by the amount of water = ?
m: mass of the water
c: specific heat of water = 1cal/g°C
T2: final temperature of water = 11°C
T1: initial temperature = 12°C
The amount of water is calculated by using the information about the density of water (1g/ml):
[tex]m=\rho V=(1g/ml)(514ml)=514g[/tex]
Then, you replace the values of all parameters in the equation (1):
[tex]Q=(514g)(1cal/g\°C)(11\°C-12\°C)=-514cal[/tex]
The amount of water losses a heat of 514 cal
The temperature difference between the inside and the outside of an automobile engine is 434 C°. Express this temperature difference on:
a. The Fahrenheit scale.
b. The Kelvin scale.
Answer:
434°C=813.2 °F
434°C=707.15 K
Explanation:
Fahrenheit is a temperature scale that sets the freezing point of water to 32 degrees Fahrenheit (° F) and the boiling point to 212 ° F (at normal atmospheric pressure). The conversion from degrees celsius to gradis fahrenheit is done by: ℉ = ℃ * 1.80+ 32.00
So, being 434°C: ℉ = 434℃ * 1.80+ 32.00= 813.2
Then: 434°C=813.2 °F
Kelvin is the temperature unit of the International System. It is one of the seven basic temperature units. Its symbol in the international system of units is K. Zero on the Celsius scale or degrees Celsius (0 ° C) is defined as the equivalent of 273.15 K. Then the conversion of Census degrees to Kelvin degrees is done by: K = ℃ + 273.15
Being 434 °C: K=434 °C+273.15=707.15
Then: 434°C=707.15 K
A long cylindrical rod of diameter 200 mm with thermal conductivity of 0.5 W/m⋅K experiences uniform volumetric heat generation of 24,000 W/m3. The rod is encapsulated by a circular seeve having an outer diameter of 400 mm and a thermal conductivity of 4 W/m⋅K. The outer surface of the sleeve is exposed to cross flow air at 27∘C with a convection coefficient of 25 W/m2⋅K.
(a) Find the temperature at the interface between the rod and sleeve and on the outer surface.
(b) What is the temperature at the center of the rod?
Answer:
a, 71.8° C, 51° C
b, 191.8° C
Explanation:
Given that
D(i) = 200 mm
D(o) = 400 mm
q' = 24000 W/m³
k(r) = 0.5 W/m.K
k(s) = 4 W/m.K
k(h) = 25 W/m².K
The expression for heat generation is given by
q = πr²Lq'
q = π . 0.1² . L . 24000
q = 754L W/m
Thermal conduction resistance, R(cond) = 0.0276/L
Thermal conduction resistance, R(conv) = 0.0318/L
Using energy balance equation,
Energy going in = Energy coming out
Which is = q, which is 754L
From the attachment, we deduce that the temperature between the rod and the sleeve is 71.8° C
At the same time, we find out that the temperature on the outer surface is 51° C
Also, from the second attachment, the temperature at the center of the rod was calculated to be, 191.8° C
If the number of loops in a coil around a moving magnet doubles, the emf created:_________
a. Doubles
b. Halves
c. Remains the same
Answer is a. Doubles
when the loops are increased in the coil then the magnetic field created doubles
A satellite in the shape of a solid sphere of mass 1,900 kg and radius 4.6 m is spinning about an axis through its center of mass. It has a rotation rate of 8.0 rev/s. Two antennas deploy in the plane of rotation extending from the center of mass of the satellite. Each antenna can be approximated as a rod of mass 150.0 kg and length 6.6 m. What is the new rotation rate of the satellite (in rev/s)
Answer:
6.3 rev/s
Explanation:
The new rotation rate of the satellite can be found by conservation of the angular momentum (L):
[tex] L_{i} = L_{f} [/tex]
[tex] I_{i}*\omega_{i} = I_{f}*\omega_{f} [/tex]
The initial moment of inertia of the satellite (a solid sphere) is given by:
[tex] I_{i} = \frac{2}{5}m_{s}r^{2} [/tex]
Where [tex]m_{s}[/tex]: is the satellite mass and r: is the satellite's radium
[tex] I_{i} = \frac{2}{5}m_{s}r^{2} = \frac{2}{5}1900 kg*(4.6 m)^{2} = 1.61 \cdot 10^{4} kg*m^{2} [/tex]
Now, the final moment of inertia is given by the satellite and the antennas (rod):
[tex] I_{f} = I_{i} + 2*I_{a} = 1.61 \cdot 10^{4} kg*m^{2} + 2*\frac{1}{3}m_{a}l^{2} [/tex]
Where [tex]m_{a}[/tex]: is the antenna's mass and l: is the lenght of the antenna
[tex] I_{f} = 1.61 \cdot 10^{4} kg*m^{2} + 2*\frac{1}{3}150.0 kg*(6.6 m)^{2} = 2.05 \cdot 10^{4} kg*m^{2} [/tex]
So, the new rotation rate of the satellite is:
[tex] I_{i}*\omega_{i} = I_{f}*\omega_{f} [/tex]
[tex]\omega_{f} = \frac{I_{i}*\omega_{i}}{I_{f}} = \frac{1.61 \cdot 10^{4} kg*m^{2}*8.0 \frac{rev}{s}}{2.05 \cdot 10^{4} kg*m^{2}} = 6.3 rev/s[/tex]
Therefore, the new rotation rate of the satellite is 6.3 rev/s.
I hope it helps you!
Consider two identical springs. At the start of an experiment, Spring A is already stretched out 3 cm, while Spring B remains at the zero position. Both springs are then stretched an additional three centimeters. What conclusion can you draw about the force required to stretch these springs during the experiment
Answer:
Explanation:
In this interesting exercise we have that spring A is 3 cm longer, due to previous experiments if these experiments did not reach the non-linear elongation point, the cosecant Km of the spring must remain the same, therefore when we lengthen the two springs these the longitudinal are lengthened.
As a consequence of the above according to Hockey law, the prediction of lengthening is the same, therefore the outside is the same in two two systems
F = K Δx
A swimmer of mass 64.38 kg is initially standing still at one end of a log of mass 237 kg which is floating at rest in water. He runs toward the other end of the log and dives off with a horizontal speed of 3.472 m/s relative to the water. What is the speed of the log relative to water after the swimmer jumps off
Answer:
0.9432 m/s
Explanation:
We are given;
Mass of swimmer;m_s = 64.38 kg
Mass of log; m_l = 237 kg
Velocity of swimmer; v_s = 3.472 m/s
Now, if we consider the first log and the swimmer as our system, then the force between the swimmer and the log and the log and the swimmer are internal forces. Thus, there are no external forces and therefore momentum must be conserved.
So;
Initial momentum = final momentum
m_l × v_l = m_s × v_s
Where v_l is speed of the log relative to water
Making v_l the subject, we have;
v_l = (m_s × v_s)/m_l
Plugging in the relevant values, we have;
v_l = (64.38 × 3.472)/237
v_l = 0.9432 m/s
One kind of baseball pitching machine works by rotating a light and stiff rigid rod about a horizontal axis until the ball is moving toward the target. Suppose a 144 g baseball is held 82 cm from the axis of rotation and released at the major league pitching speed of 87 mph.
Required:
a. What is the ball's centripetal acceleration just before it is released?
b. What is the magnitude of the net force that is acting on the ball just before it is released?
Answer:
a. ac = 1844.66 m/s²
b. Fc = 265.63 N
Explanation:
a.
The centripetal acceleration of the ball is given as follows:
ac = v²/r
where,
ac = centripetal acceleration = ?
v = speed of ball = (87 mph)(1 h/ 3600 s)(1609.34 m / 1 mile) = 38.9 m/s
r = radius of path = 82 cm = 0.82 m
Therefore,
ac = (38.9 m/s)²/0.82 m
ac = 1844.66 m/s²
b.
The centripetal force is given as:
Fc = (m)(ac)
Fc = (0.144 kg)(1844.66 m/s²)
Fc = 265.63 N
minerals all have a ___ structure with the same ___ composition. 1. a. heterogeneous b. homogeneous 2. a. physical b. chemical
Explanation:
1 b. homogenous.
2 b. chemical.
Hope this helps
g A 10.0 g bullet is fired into and embeds itself in a 1.65 kg block attached to a spring with a spring constant of 17.2 N/m and whose mass is negligible. How far is the spring compressed if the bullet has a speed of 300 m/s just before it strikes the block, and the block slides on a frictionless surface? (Note: You must use conservation of momentum in this problem.
Answer:
the compression of the spring is 0.5613 m
Explanation:
Given;
mass of bullet, m₁ = 0.01 kg
mass of block, m₂ = 1.65 kg
initial velocity of the block, u₂ = 0
initial velocity of the bullet before hitting the block, u₁ = 300 m/s
Final speed of the bullet-block system after collision, v = ?
spring constant, K = 17.2 N/m
Apply the principle of conservation of linear momentum;
m₁u₁ + m₂u₂ = v( m₁ + m₂)
0.01 x 300 + 1.65 x 0 = v(0.01 + 1.65)
3 = 1.66v
v = 3 / 1.66
v = 1.807 m/s
Apply the principle of conservation of mechanical energy to determine the compression of the spring;
KE₁ + PE₁ = KE₂ + PE₂
¹/₂mu² + ¹/₂Kx₁² = ¹/₂mv² + ¹/₂Kx₂²
where;
m is mass of bullet and block embedded together
u is the initial velocity of the bullet-block system = 1.807 m/s
v is the final velocity of the bullet-block system = 0
x₁ is the initial compression of the spring = 0
x₂ is the final compression of the spring = ?
¹/₂(1.65 + 0.01) (1.807)² + ¹/₂(17.2)(0)² = ¹/₂(1.65 + ).01)(0)² + ¹/₂(17.2)(x₂)²
2.71 + 0 = 0 + 8.6(x₂)²
(x₂)² = 2.71 / 8.6
(x₂)² = 0.3151
x₂ = √0.3151
x₂ = 0.5613 m
Therefore, the compression of the spring is 0.5613 m