Answer:
The average force on the bullet will be "2607.43 N".
Explanation:
The given values are:
Mass of the bullet,
m = 4.2 g
Final speed,
v = 965 m/s
Initial speed,
u = 0
Distance,
S = 0.75 m
According to the Energy theorem,
⇒ [tex]Work \ done = Change \ in \ kinetic \ energy[/tex]
⇒ [tex]F S = (\frac{1}{2} )m(v^2 - u^2)[/tex]
On substituting the values, we get
⇒ [tex]F\times 0.75=0.5\times 0.0042 [(965)^2 - 0][/tex]
⇒ [tex]0.75 F = 0.5\times 0.0042\times 931225[/tex]
⇒ [tex]0.75F=1955.57[/tex]
⇒ [tex]F=\frac{1955.57}{0.75}[/tex]
⇒ [tex]=2607.43 \ N[/tex]
Geologists know the past temperature of the planet based on rock and fossil evidence. Why do you think it is difficult to determine what has caused climate change in the distant past?
Answer:
I think it is difficult to determine what has caused climate change in the distant past because it must have been a long time ago so geologists can't carry out different experiments and figure out what gases the planet had conjured, so geologists can only make predictions based off the evidence they currently have from what the planet looked like before. The planet must have changed over the years, therefore the climate has also changed in the future, so they cannot work with how the planet looked in the past.
Why do specific heat capacity of objects differ ?
Answer:
substances have different melting and boiling points to one another.
Explanation:
Explanation:
Each substance will have a different mass, so when the amount of heat and the change in temperature are held constant, the only variable is the mass. Therefore, because mass is the only variable, so because substances have different masses, they will have different specific heats.
How many joules of heat energy are needed to raise the temperature of 10.0 g (0.0100 kg) of aluminum from 22 K to 55 K, if the specific heat of aluminum is 897 J/kg * K. Explain your answer
Answer:
296.01 J
Explanation:
From the question,
Q = cm(t₂-t₁)....................... Equation 1
Where Q = quantity of heat, c = specific heat capacity of aluminium, m = mass of aluminium, t₁ = Initial temperature, t₂ = Final temperature
Given: c = 897 J/kg.K, m = 0.01 kg, t₁ = 22 K, t₂ = 55 k
Substitute these values into equation 1
Q = 897×0.01×(55-22)
Q = 897×0.01×33
Q = 296.01 J
Hence 296.01 Joules of heat is required.
Which are advantages of renewable resources? Check all that apply.
Renewable energy supplies are completely reliable everywhere.
Some renewable resources will never be used up.
Little or no waste is produced by renewable resource plants.
Electricity can be generated in large quantities.
Many renewable energy facilities have lower operating costs.
Answer:
Some renewable resources will never be used up.
Little or no waste is produced by renewable resource plants.
Many renewable energy facilities have lower operating costs.
Explanation:
just did on edge
Answer:
B,C, and E are correct
Explanation:
A train A travelled a distance of 150 km in 3 hours, whereas, train 'B"
travelled a distance of 180 km in 4 hours. Which train travelled faster?
Answer:
Therefore, Train A is faster with 50km/h and a 5km/h difference
Explanation:
train A
150km/3h = 50km/h
train B
180km/4h = 45km/h
2 kg
T2
5 kg
2.1.1 State Newton's Second Law of Motion in words.
.1.2 Draw a labelled free body diagram for the 2 kg mass.
1.3 Determine the magnitude of the tension force T2.
1.4 Calculate the magnitude of the normal force exerted on the 2 kg mass,
Answer:
2500 and kg its is very easy do with method
if a car exerts a area of 3m and a force of 9N what is the pressure exerted by car
Answer:
P = 3 Pa
Explanation:
Given that,
Force exerted by the car, F = 9 N
The area of the car, A = 3 m²
We need to find the pressure exerted by the car. We know that pressure is equal to the force per unit area such that,
[tex]P=\dfrac{F}{A}\\\\P=\dfrac{9\ N}{3\ m^2}\\\\P=3\ Pa[/tex]
So, the pressure exerted by the car is equal to 3 Pa.
If a person perceives that he has some control over his environment, he most likely will handle stress:
a.poorly
b.by retreating from the stress
c.the same as everyone else
d.better than if he doesn't feel in control
X=Y=MC scourer that would be the answer for you mam or sir
Me das mas información?
Answer:
jello
Explanation:
it jiggles
4) A drag racer starts her car from rest and accelerates at 10.0 m/s² for a distance of 400 m (1/4 mile). (a) How long did it take the race car to travel this distance? (b) What is the speed of the race car at the end of the run?
Answer:
A) s=1/2at^2
t=√(2s/a)=√(2x400)/10.0)=9.0s
B) v=at
v=10.0x9=90m/s
PLEASE HELP!!!!!!!!!!!!!
a. A light wave travels through glass (n=1.5) at an angle of 28°. What angle does it have when
it passes from the glass into water (n = 1.33)?
B. Draw a ray diagram to locate the image of the object below. Write one or two sentences to describe the type of image, it’s size relative to the object, and it’s position with respect to the lens.
C. An object is located 94.0 cm from a concave mirror. The focal length is 34.0 cm. What is the image distance? Is the image real or virtual??
D. An Object is located 65.0 cm from a concave lens. The image distance is -11.8 cm. What is the magnification?
E. For a person who is nearsighted, seeing objects that are far away is difficult. The light from these objects does not get focused far enough back in the eye. Write one or two sentences to identify the type of lens that can be used to correct nearsightedness and describe why it works.
PLEAAAASE HELP MEEE
Answer:
A. The angle with which the light passes from glass into water is approximately 31.97°
B. The image formed is, real, inverted, and smaller than the object
C. The image distance is 53.2[tex]\overline 6[/tex] cm
The image is real
D. The magnification is approximately 0.182
E. The type of lens required is a concave lens which corrects the focus of a powerful eye lens or a long eyeball
Explanation:
The given parameters for the light wave are;
The refractive index of the glass medium, n₁ = 1.5
The angle of incidence of the light, θ₁ = 28°
The refractive index of water, n₂ = 1.33
A. Let θ₂ represent the angle with which the light passes from glass into water
Snell's law is mathematically stated as follows;
n₁·sin(θ₁) = n₂·sin(θ₂)
According to Snell's law, we have;
1.5 × sin(28°) = 1.33 × sin(θ₂)
sin(θ) = (1.5 × sin(28°))/1.33 = 0.52947920615
∴ θ₂ = arcsin(0.52947920615) ≈ 31.97°
The angle with which the light passes from glass into water, θ₂ ≈ 31.97°
B. Please find attached the drawing of the image created with Microsoft Visio
From the drawing, we have that the image formed is real inverted smaller than the object and between the focus and radius of curvature
C. The location of the object from the mirror, u = 94.0 cm
The focal length of the mirror, f = +34.0 cm
The mirror formula for a concave mirror is given as follows;
[tex]\dfrac{1}{f} = \dfrac{1}{u} + \dfrac{1}{v}[/tex]
Therefore, we have;
[tex]\dfrac{1}{34.0} = \dfrac{1}{94.0} + \dfrac{1}{v}[/tex]
[tex]\dfrac{1}{v} = \dfrac{1}{34.0} - \dfrac{1}{94.0} = \dfrac{15}{799}[/tex]
[tex]\therefore \dfrac{v}{1} = v =\dfrac{799}{15} = 56.2\overline 6[/tex]
The image distance, v = 799/15 = 53.2[tex]\overline 6[/tex] cm
Therefore the image is in front of the mirror, which is a real image
The image is real
D. The given parameters of the object and lens are;
The distance of the object from the lens, u = 65.0 cm
The distance of the image formed from the lens, i = -18 cm
The magnification, M, is given as follows;
[tex]M = \dfrac{-v}{u}[/tex]
Therefore;
[tex]M = \dfrac{-(-11.8)}{65.0} = \dfrac{59}{325} \approx 0.18153846153[/tex]
The magnification, M ≈ 0.182
E. For a person who is near sighted, the light from objects from distant location are almost parallel and are brought to a focus in front of the retina and therefore, they appear blurred
The use of a concave lens is required to correct nearsightedness as it causes the light to appear come from a point before the focus such that the divergent rays of the object refracted through the concave lens comes to a focus at the.
A 0.15-m straight wire moves with a constant velocity of 7.0 m/s perpendicularly
through a magnetic field. If the magnetic field has a strength of 0.40 T, what is the
electromotive force?
Answer: force is 0.42 N
Explanation: F = l·v·B
Hahah I look pregnant don’t I
If you place apiece of foil, a piece of black fabric, and a white sheet of paper all the same size in the sun for five minutes, which would absorb the most heat. Which would absorb the least heat? Briefly explain why.
A spinning wheel on a fireworks display is initially rotating in a counterclockwise direction. The wheel has an angular acceleration of -4.20 rad/s2. Because of this acceleration, the angular velocity of the wheel changes from its initial value to a final value of -26.0 rad/s. While this change occurs, the angular displacement of the wheel is zero. (Note the similarity to that of a ball being thrown vertically upward, coming to a momentary halt, and then falling downward to its initial position.) Find the time required for the change in the angular velocity to occur.
Answer:
The time it takes for the change in the angular velocity to occur is 6.5 seconds
Explanation:
From the question, we have;
The angular acceleration of the wheel, α = -4.20 rad/s²
The final angular velocity of the wheel, ω = -26.0 rad/s
From the information, we have the initial direction of rotation of the wheel = Counterclockwise
The angular displacement while the change occurs = 0 rad/s
Therefore, the initial angular velocity of the wheel, ω₀ = 0 rad/s
We have;
[tex]\alpha = \dfrac{\omega -\omega _0 }{t - t_0}[/tex]
Where;
t - t₀ = The time it takes for the change to occur
[tex]\alpha = \dfrac{\omega -0 }{t - 0}[/tex]
When t₀ = 0, we have;
t - t₀ = t
[tex]\alpha = \dfrac{\omega }{t}[/tex]
[tex]\therefore t = \dfrac{\omega}{\alpha }[/tex]
[tex]\therefore t = \dfrac{-26 \, rad/s}{-4 \, rad/s^2 } \approx 6.5 \, seconds[/tex]
The time it takes for the change in the angular velocity to occur is t - t₀ = 6.5 seconds
Exercising at light, moderate, or vigorous level is referring to the
a
frequency
b
intensity
c
time
d
type
Answer is in the file below
tinyurl.com/wpazsebu
Brainliest for correct answers :)
Please look at both pictures and answer correctly for brainliest
Answer:
a. 1100 meters.
b. Between B and C
c.1. Between point D and E
c2. Between point D and E
d. 3.7 m/s.
Explanation:
The girl travels the distance of 1100 meters from starting to the end. There is no motion occurs between B and C due to no change of distance value from 200 meters. Between point D and E, the girls covers 500 meters long distance and also covers fastest distance between point D and E because between point D and E, the girl covers 500 meters distance in 30 seconds which is the highest of all. The average speed of the girls is 3.7 meter/seconds if we divide total distance i.e. 1100 meters by time which is 300 seconds.
AWARDING BRAINLIEST
Compared to water, most metals have low specific heats.
Please select the best answer from the choices provided
T
F
Answer:
it is true
Explanation:
i think so
not really sure
It is common for creatures to be able to live in both the spray zone and low-tide zone.
True or False
Hii!!! The correct answer is true. (:
A seller on the internet claims to have pieces of a wooden statue that are 2000 years old. You are asked to date the wood to see whether the age is correct. The 20g sample you receive has an activity of 15 counts per second. For living wood. 20g would have an activity of 16 counts per second. Estimate the age of the wood and women’s on weather the sellers claims are true
Two waves have the same amplitude and are traveling through the same medium, but the first wave has a higher frequency. The energy of the first wave is greater than that of the second.
True or false?
Two waves have the same amplitude but they can have different frequencies. The wave with a higher frequency will have greater energy. Therefore, the given statement is correct.
What are frequency and wavelength?The frequency of electromagnetic waves or any wave can be described as the number of oscillations in one second. The frequency can be represented as per second or hertz.
The wavelength of the wave can be defined as the distance between two crests or troughs on a wave that is separated by a distance known as wavelength. The wavelength of the waves is expressed in meters.
The relationship between frequency (ν) and energy of the wave:
E = hν
The frequency of the waves has a direct relation with the energy of the waves. Therefore, the wave which has a higher frequency will carry greater energy whether they have the same amplitude.
Learn more about wavelength and frequency, here:
brainly.com/question/18651058
#SPJ2
When solar energy is converted to thermal energy, how is the thermal energy used? Check all that apply.
to provide air conditioning
to cool refrigerators
to heat spaces in buildings
to heat water
Answer:
to heat spaces in buildingss
Explanation:
An object moves from point A to point B to point C, then back to point B and then to point C along the line
Answer:
Rectilinear propagation of light
Why is this statement false?
As the temperature of water is decreased from 4C to 0C contraction occurs.
The statement is false because as the temperature of water is decreased from 4C to 0C, expansion occurs.
You should understand that this is very weird behavior for any compound ... within a small temperature range, the stuff actually gets bigger as it gets colder. That's why cubes float in your sody, and bergs float in the ocean.
Water is one of only two known substances that do this. And if water didn't do it, then life on Earth would not be possible.
Hmmm....
There is not contraction, Instead expansion occurs .
We know density of water is temperature dependant .
at 4°C water has max density so least volume as density is indirectly proportional to volume.
at 0°C density decreases so volume increases
Derive, with full working, the symbol equation for the power output P watts of the energy transfer that occurs when a mass of m kg falls through a height of h metres in t seconds.
an organism that cannot make its own food called
Answer:
heterotroph
Explanation:
Answer:
a predator cannot make its own food
An athlete whirls a 8.00 kg hammer m from the axis of rotation in a horizontal circle, as shown in the figure below . The hammer makes one revolution in s. What is the centripetal force on the hammer ?
Answer:
[tex]mv \div r \\ mass \times velocity \div radius[/tex]
what is the equation for net force
Answer:
Is to add all forces, for example either the gf = gravitational force
Ff= force fiction
Fn= normal force
Thus, fg + ff + fn = y will give you results
Well then the forces you use in your exercises or questions.
The equation for net force is: ΣF = ma
or, ΣF = Δp/Δt.
What is force?The definition of force in physics is: The push or pull on a massed object changes its velocity.
An external force is an agent that has the power to alter the resting or moving condition of a body. It has a direction and a magnitude. The application of force is the location at which force is applied, and the direction in which the force is applied is known as the direction of the force.
A spring balance can be used to calculate the Force. Newton is the SI unit of force.
Hence, net force applied on the object = mass × acceleration
ΣF = ma
It can be written in another from as:
net force applied on the object = change in momentum ÷ time interval
ΣF = Δp/Δt
So, the equation for net force is: ΣF = ma
or, ΣF = Δp/Δt.
Learn more about force here:
https://brainly.com/question/13191643
#SPJ2
The two objects we need to make electricity are
Answer:
Explanation:
.
You have two rocks made of the same material that are at the same
temperature. The first rock has three times the mass of the second rock. How
does the thermal energy of the two rocks compare?
A. The second rock has three times the thermal energy of the first rock
B. The first rick has six times the thermal energy of the second rock
C. The second rock has one-third as much thermal energy as the first rock
D. The rocks have the same amount of thermal energy
Answer:
the rocks have the same amount of thermal energy